Regarding Barcode dimm module

Hi
Anybody has come accross the scenario, where we have to install a barcode dimm module on the printer , for barcode printing??

Check out this OSS Note #121305
it might give you information.

Similar Messages

T23 and 512 MB - DIMM - modules don't work with each other, getting only beeps

Hi there,
I searched the whole web, but nowhere getting the answer.
I'm having an Thinkpad T23 2647 with XP.
Actually it works without problems with 2 kind of 256 MB modules.
When I try to change it to one ore more 512MB modules, it comes the known beep-signal for dimm-failure (there is no combination possible, even standalone doesn't work).
I've the newest BIOS (1.20) and Embedded Controller (1.06a) installed.
The dimm-modules are 512 MB SDR PC133 with 144 pins bought via Ebay from CSL Computers in germany.
I had the same problems a year before, but there I thougt it was the DIMM defect.
I need further help please.
Thanks and best wishes

It is possible that the T23 motherboard has a problem with some bad solder connections of the memory module sockets. I have personally have had at least two T23 systems with this problem (out of about 60 that have been in my hands - all purchased quite used from eBay). Your options are to change out the motherboard or to attempt to re-solder the sockets; not that easy to do but it can be possible with a steady eye and good hands (or is that the other way around ).
As a double-check, could you please list the TYPE number from the "System-unit serial number" in the main BIOS setup screen? It's only seven characters long and will start with 2647 or 2648. Don't list anything past the seventh character as that's the system's serial number and that's not needed here. I know that you've listed the 1.20 BIOS, which appears to be the latest for the T23, but I want to make sure that somebody hasn't put a T23 keyboard onto a T22 (or earlier) system. That would be one explanation as to why a 512MB module does not work and what fmyhr may have been thinking about earlier (systems older than the T23 will not work with "high density" modules).
Ray Kawakami
X22;X24;X31;X41;X41T;X60;X60s;X61s;X300;X301;Z60m;Z61t;Z61p;560Z;600E;600X;T21;T22;T23;T41;R50;A21p;A22p;A31 and A31p
Not a Lenovo employee; just a volunteer helping out here
All personal links to PC-Doctor software removed 8/2012 by mfg request

Dump regarding 'Error in module RSQL 'in dynamic internal table

Here is a Dump regarding 'Error in module RSQL of the database interface'.My program runs fine if 100 rows is getting selected from SAP Table.But for mass selection program is giving Dump. The program has dynamic selection of any SAP Table with dynamic selection ranges.I have attached below snippet code for your understanding and analysis.
Looking forward your kind support.
* Select Data from table using field symbol which points to dynamic table with packet size
SELECT *
 INTO CORRESPONDING FIELDS OF TABLE <fs_table_tmp>
 FROM (p_table) PACKAGE SIZE p_packet.
 INSERT LINES OF <fs_table_tmp> INTO TABLE <fs_table> .
 UNASSIGN <fs_table_tmp> .
ENDSELECT.

Hello Salmali,
Are you checking in the debugger mode?
Error CX_SY_OPEN_SQL_DB comes when there is any pause between select and endselect.
one more thing use INTO in place of APPENDING.
SELECT (i_field_select)
 FROM (p_table)
 into CORRESPONDING FIELDS OF TABLE <fs_table_tmp>
 PACKAGE SIZE p_packet.
 append LINES OF <fs_table_tmp> INTO TABLE <fs_table> .
 Refresh <fs_table_tmp> .
ENDSELECT.
Please let me know what is the value of p_packet.
also have you created the table <fs_table_tmp> and <fs_table> of same type . Please check
Thanks,
Gaurav

Regarding Lightroom Slideshow module: When I click on the preview button I get the following error: An internal error has occurred: ?:0: attempt at index a nil value. This occurs with any group of images I select in my catalog.

Regarding Lightroom Slideshow module: When I click on the preview button I get the following error: An internal error has occurred: ?:0: attempt at index a nil value. This occurs with any group of images I select in my catalog.

Jeannine,
If you follow the advice of the previous poster Julie Kmoch and then gradualy add presets back in one at a time you might be able to find the one that is causing the issue. I may be guessing, but I believe the issue has something to do with either an incompatible Preset setting (eg a older preset in newer version of LR) or a corrupt Preset.
Say you bought LR2 and imported a bunch of Presets from the internet, cuz 'Hey these effects are cool and I don't have to recreate the wheel', and then you upgraded to LR3 (not a clean install) and now one of the Presets that calls a certain slider setting or value that is different in LR3 doesn't work anymore. This might be why it throws the error, but again I am just speculating.
Location of LR Preset folder in Windows Vista/ Windows 7
C:/Users/<YourUserName>/AppData/Roaming/Adobe/Lightroom/Develop Presets
If you do not see the folder AppData, you may need to change the settings in Windows Explorer to 'Show Hidden Files and Folders'. To do that in Windows Vista/ Windows 7, open a Windows Explorer window, Click on Organize, then Foler and Search Options. Then click on the View tab and select the option button next to Show hidden files, folders and drives.
Hope this helps a bit,
Glenn

Same FB-DIMM modules for all MacPro models?

Is the same FB-DIMM module use for 2.0GHz and 3.0GHz Mac Pros, or are they different Apple parts? Thanks.
blakespot

Nope… the FB-DIMM spec is the same for all models.

Function Module regarding Barcode

Hello Everybody,
Please tell some FM which take input and generate barcode.
Regards.
Sarbajit.

Hi Anup ,
In OAC5, I have set Object Type VBRK as
BCodeType:- UPC_A
and checked all the checkbox.
And trying to run the BDSBARIN with input Bar code type : UPC_A
                                                                  Object type   : VBRK
                                                                  Object key    : 1
                                                               Document type : BDS_IMAGE
                                                               Bar code : Bar code
ad left other input field blank.Now I'm getting error like SAP ArchiveLink: Objects not assigned to a storage system(Customizing).
Need your help.
Thanks in Advance.
Regards.
Sarbajit

Regarding Barcode Type....

Hi friends...
     How can I get the information about the attributes of different barcode types   used in Smartforms?
Kindly Suggest me the solution for this query???
Points will be rewarded to the useful answer...
Thanx,
Rahul.

Hi Rahul,
You can use barcodes types already created or you can create new one if
these types does not satisfy you requirement.
If you create a new system bar code for the "new bar code technology" in transaction SE73, you must specify the following parameters:
Bar code name (used in Smart Styles)
Short text for system bar code (documentation)
Bar code symbology:
    Code39
    Code128
    Interleaved 2of5
    PDF417
    Code93
This selection determines the technical bar code type that is used to format the bar code data (also called bar code symbology). The symbology also determines which characters are allowed in the bar code data.
Bar code alignment:
Normal (that is, the scan direction is "from left to right")
Rotated (the scan direction is rotated by 90 degrees "from top to bottom")
Inverted (the scan direction is rotated by 180 degrees "from right to left")
Bottom-up (the scan direction is rotated by 270 degrees "from bottom to top")
Code39 ******************
Code39 is an alphanumeric code that can represent the following characters in the bar code data:
Numbers:        1234567890
Capital letters: ABCDEFGHIJKLMNOPQRSTUVWXYZ
Special characters: - . $ / + %
Blank characters (space characters)
The start and stop character for the Code39 bar code is usually represented by an asterix (*) in the text view of the bar code data (also called "human-readable text" or "interpretation line").
Parameters for Code39:
Narrow module width
Value range: 1 to 10
This is the width for the narrowest module of a bar code, measured in pixels. It controls the width of the bar code. Value 1 generates the "narrowest", value 10 the widest bars or spaces.
Linear height
Value range: 1 to 9999
Controls the height of the bars of the bar code, measured in pixels. A value of 600 is equal to a height of one inch.
Mod-43 check digit
Value range: X equals YES, blank character equals No
With this indicator, you can determine whether a Modulo-43 check digit is to be generated.
Bar ratio
Value range: 20 to 30
This value controls the ratio between wide and narrow bars. This value controls the ratio between wide and narrow bars.Value 20 means a ratio of 2.0:1, value 30 means a ratio of 3.0 to 1 (that is, 3:1).
Parameters for Interleaved 2of5:
Narrow module width
Value range: 1 to 10
This is the width for the narrowest module of a bar code, measured in pixels. It controls the width of the bar code. Value 1 generates the "narrowest", value 10 the widest bars or spaces.
Linear height
Value range: 1 to 9999
Controls the height of the bars of the bar code, measured in pixels. A value of 600 is equal to a height of one inch.
Mod-10 check digit
Value range: X equals YES, blank character equals No
With this indicator, you can determine whether a Modulo-10 check digit is to be generated.
Bar ratio
Value range: 20 to 30
This value controls the ratio between wide and narrow bars. This value controls the ratio between wide and narrow bars.Value 20 means a ratio of 2.0:1, value 30 means a ratio of 3.0 to 1 (that is, 3:1).
Code 128 *****************
Code128 is an alphanumeric code that can encode three different character sets. Each of the three character sets can represent 106 different characters. Within a bar code, you can alternate between the character sets.
The three Code128 character sets are named as follows:
Subset A) (contains, for example, digits, capital letters and control characters)
Subset B) (contains, for example, digits, uppercase and lowercase letters)
Subset C) (digit pairs from 00 to 99)
Parameters for Code128:
Narrow module width
Value range: 1 to 10
This is the width for the narrowest module of a bar code, measured in pixels. It controls the width of the bar code. Value 1 generates the "narrowest", value 10 the widest bars or spaces.
Linear height
Value range: 1 to 9999
Controls the height of the bars of the bar code, measured in pixels. A value of 600 is equal to a height of one inch.
Code128 mode
Value range: N (default value), A, U
In default mode N (None), the Code128 bar code works in subset B. If you want to switch to another subset, you must trigger the change explicitly with a control command ("invocation code") in the bar code data.
In mode A (automatic), the software analyzes the transferred bar code data and recognizes automatically which subset is the most adequate for the bar code data. Subsets are swapped automatically in the bar code data. A sequence of four or more digits initiates an automatic change in subset C.
In mode U (UCC case mode), you must transfer 19 digits in the bar code data. Subset C is set automatically and an FNC1 character is added as prefix.
Note: If fewer than 19 digits are transferred, the bar code is filled with zeros to the left until it contains 19 digits.
UCC check digit
Value range: X equals YES, blank character equals No
Note: This parameter has no effect becaues Code128 always generates a check digit, even in UCC mode. The parameter will be removed in the future.
Code93 is an alphanumeric code that can represent the following characters directly in the bar code data:
Numbers:        1234567890
Capital letters: ABCDEFGHIJKLMNOPQRSTUVWXYZ
Special characters: - . $ / + %
Blank characters (space characters)
The start and stop characters in the Code93 bar code are represented as # sign in the text view of the bar code data (also called "human-readable text" or "interpretation line").
Parameters for Code93:
Narrow module width
Value range: 1 to 10
This is the width for the narrowest module of a bar code, measured in pixels. It controls the width of the bar code. Value 1 generates the "narrowest", value 10 the widest bars or spaces.
Linear height
Value range: 1 to 9999
Controls the height of the bars of the bar code, measured in pixels. A value of 600 is equal to a height of one inch.
Check digit
Value range: X equals YES, blank character equals No
With Code93 bar codes, a pair of check digits is always used and is always generated in the bar code. This parameter has no effect.
PDF417 is a two-dimensional bar code to represent datasets that are larger as the usual datasets in one-dimensional bar codes (for example, more than 1,000 characters). The entire 7-Bit ASCII character set is generally processed (binary values 1 - 127, the value 0 is not permitted).
A PDF417 bar code consists of 3 to 90 consecutive rows. Every row consists of a start/stop indicator and "code words". A code word consists of 4 bars and 4 spaces. The minimum number of code words per row is three.
Parameters for PDF417:
Narrow module width
Value range: 1 to 10
This is the width for the narrowest module of a bar code, measured in pixels. Value 1 generates the "narrowest", value 10 the widest bars or spaces.
Linear height
Value range: 1 to 9999
This parameter currently has no effect on PDF417. The height of a PDF417 symbol is controlled by parameter "Single Row Height" and the number of columns and rows, in conjunction with the length of text data to be encoded.
Single row height
Value range: 1 to 32000
This value, multiplied by the narrow module width, returns the height of the individual rows of a PDF417 symbol, measured in pixels. Caution: Do NOT use the value 1 for this parameter
Security level
Value range: 0, 1-8
This parameter controls the number of code words that are generated for error recognition and error correction. The default value 0, however, only permits error recognition but no automatic correction. If you increase the security level, the level of error correction increases with it (this increases the size of the bar code).
Number of columns
Here, you can define the number of the code word columns which you can use to check the width of the bar code.
Value range:
0 (default value) : A row/column ratio of 1:2 is used.
Permitted values: 1 to 30
Number of rows
Here, you can define the number of rows which can be used to check the height of the bar code.
Value range:
0 (default value) : A row/column ratio of 1:2 is used.
Permitted values: 3 to 90
For example: If you leave both parameters set to the default value 0, the system would convert 72 code words in a bar code symbol with 6 columns and 12 rows.
Truncation
Value range: X equals YES, blank character equals No
This indicator determines if the right row indicator and the stop pattern are to be truncated (this saves space).
The following character combinations in the transferred bar code data have the special function:
\&    - This represents the end of a line (Carriage Return + Newline)
    - This represents a backslash (5C hexadecimal)
\0xYY - This represents a single byte with the value YY (hexadecimal)
        For example: \0x1E is output as a single byte with the value 1E (hex)
        or 30 (decimal).
The souce for this information is OSS Note 645128.
Still if u face any problem feel free to ask.
Regards,
Vivek
-Reward if useful

Need detail information regarding Barcode Integration with SAP

Hi All,
Wanted to know the steps in integrating SAP system with the existing barcode reader. I need to know how to read and attatch the barcode reader and how to process the barcode. It will also be helpful if relevant documents are supplied.

If I'm understand your question correctly, you want to send the order you receive on your web to the manufacturer. Then manufacturer will create a sales order and delivery order on their side and deliver the good to the clinic.
In this case,
1,2) It would be better for you to send the order to them instead of creating the wsdl for them to call. There is a standard format EDI for sales order that SAP use to interface with legacy system. You cna generate the data in this format and send to each manufacturer so they can configure the system on their side.
3) The module is called SAP order fullfillment or SAP order-to-cash or SAP SD (Sales & distribution). It means the same thing just some people call it differnetly. SAP SD is the common one.
4) Surely there will be some effort for each manufacture to integrate their system with you. However, If you use the standard EDI, the effort would be minimal for the manufaturer that already implement this with other partner.
5) you can pass along the address in sales order. If the manufacturer system implemented SAP SD, they should be able to create sales order, delivery order and invoice from their side.
Regards,
Chaiphon

Barcode in module pool

Hi All,
My client requirment is to add new field for Barcode in Tcode AS01 and also display the barcode near by.
how to achive this issue.
Regards,
Arasukumar

Hello,
Please try the Function modules in Function Group ALINK_BARCODE_BDS
BDS_BARCODE_CREATE
BDS_BARCODE_CREATE_VIA_RFC
BDSBARIN
This program is used for Generating, Creating and inserting Barcode.
Normally take on lable in disable mode and move the barcode value to that label.

Regarding Seeburger Classifier Module

Dear Expert,
I am using Seeburger EDI Adapter to handle EDI plain file into SAP XI. As I just want to use the Seeburger build-in mappings start with "See_", I did not set the parameter classifierMappingID of Seeburger Classifier Module, but always get the output of Seeburger Functional Acknowlegement. How can I set the parameters to use the build-in mappings like "See_E2X_ANSIX12_810_V4010"?
Any suggestion or idea are appreciated!
Thanks and Regards,
Nick

Hi Nick,
you need to choose if you want to use classifier or predefined mapping name. The purpose of classifier is to classify your message (exp. ANSI 12, EDIFACT etc.) and than to find the mapping specified in Seeburger Message splitter (from http://<XI Host>:<J2EE port>/seeburger/index.html -> Message splitter).
In Message splitter you need to choose you sender agreement from XI, Mapping name and sender number (for ANSIX12 it's the value of ISA06 from inbound ANSI message).
Please check Seeburger manual SAPXI_FunctionalAck_en.pdf.
If you need your communication channel to process only ANSIX12_810_V4010 messages than you don't need classifier and you can hardcoded parameter mapping name "See_E2X_ANSIX12_810_V4010".
Regards
Naycho

Questions regarding update function module

Hello experts,
I am on customer site to help them investigate one issue: they have a background job which runs periodically.
In the report database table A is changed firstly ( new entries are inserted ), then a update function module is called via keyword CALL FUNCTION ... IN UPDATE TASK.
Inside the function module database table B is updated. ( existing entries are updated )
Customer issue:
sometimes they find A is updated as expected, however B remains unchanged at the same time.
customer could not find exact steps to reproduce the issue. However the issue does exist there and occur from time to time.
the issue could only be reproduced in their production system, but works perfectly well in dev & Q system. It is difficult to debug in their production system for trouble shooting.
After analyzing related code, I have one doubt: according to ABAP help on CALL FUNCTION aaa IN UPDATE TASK, I know the function module aaa is called in a new update work process. I wonder whether there is any possibility there this issue might be caused because the update function module fails to get called at all? ( perhaps due to heavy system load so no free update function module could serve the table B update ? )
If update function module fails to execute, is there any system utility to record this? That is to say, will it be recorded in such as SM13 or SM21?
Looking forward to your expertise on this topic!
Best regards,
Jerry

Hello friends,
Thanks a lot for your interests on this issue. I update all my findings:
1. issue background: this issue occurs in SAP CRM Channel manageement Solution, software component CRM-CHM-POS.
2. due to some limitations, the table CMSD_CI_HISTORY and history table are not updated in the same LUW. Instead the first one is updated in normal work process while the other is done in update work process. Since I am not the original developer I didn't know the whole complex scenario ( I did see this is done delibrately in note 1764006 - CMS:Sell In Release creating PB with zero available quantity ).
So for the moment we have to accept this design.
3. during our testing ,we ensure COMMIT WORK is always called.
4. So why sometimes the first table update fails, however there is no hint at all for this failure in the system like ST22 and SM21 ?? ( forget SM13, since it is updated in normal work process ).
The root cause is the flaw of SAP code below.
The code has planned to raise exception if insertion failed due to duplicate records to be inserted.
Unfortunately, the fact is if we use "INSERT db FROM TABLE xxx" to insert records into database and some record already exists with the same key, it will result in a termination but SY-SUBRC is STILL 0; Just compare it with single insertion using "INSERT db FROM <work area>", in the same error situation, processing does not terminate, and SY-SUBRC is set to 4.
As a result in this case even the insertion fails, line 29 will never be executed as sy-subrc is always 0. Since the insertion fails and the exception is caught without any notification, so customer sufferred because they do not know what has happened.
Best regards,
Jerry

Help regarding the Function Module GUID_CREATE

Hi Experts,
Can some one explain the functionality of GUID_CREATE function module.Thanks in advance.
With regards,
Srini...

Hello,
Guid for unique identification assigned list
It think it will generate the one unique key in the program.
DATA: con_log_guid TYPE guid_16.
CALL FUNCTION 'GUID_CREATE'
IMPORTING
ev_guid_16 = con_log_guid.
WRITE con_log_guid .
Try this example it is generating a 16number id.

Regarding The Function Module SXMS_ASYNC_EXEC strucking In Queue

Dear All,
I have Written an Enhancement for standard Program MB52, I have written an Outbound Proxy and scheduled the job in background the Job is running successfully but default the the Function module SXMS_ASYNC_EXEC is also scheduled and is it showing an Error SYS-Fail.
Queue Block : Action OPEN_PSA_DATAPACKAGE/2 IS NOT SUPPORTED Iam Trying to Apply the Note Pls help me in this Regards
Regards
Naresh

Hi Amit,
if you are working with abap proxies there is an error in the proxy code that you have implemented.
Use the tcode SPROXY -> Proxy -> Test Interface (F8)
Best Regards,
Francesco

Regarding hr function modules

if to read the data from a RT table which of the following function module will be best
. pyxx_read_payroll_result or RP_FILL_WAGE_TYPE_TABLE
what i am doing is i am filling the rgdir table using the function module cu_read_rgdir
as looking at the query you can see i am totally confused in these function modules
can anone please let me know that how i can get data from rt using these function modules coz i am not using ldb PNP in my program and i have got all the data wihtout using it now the only issue left is PF that i can get only from RT TABLE.
if there is any other way also for that please let me know
the wage types for pf are /3f1,/3f2./3f3
if anynobdy can help me in this i can complete rest of the parts by today ..
sorry for disturbing you all have asked too many questions on rt table
please dont mind
just wanted to have a grip on it thats y asking so many queries and thanks for all your replies that you all have given
pelase help me in this last one also:)

Hi,
refer
Retrieve record from RT
Re: regarding RT tables
Hope this solves your purpose.
Award points if it helps.
-Gaurang

Regarding bapi function module

Hi to all,
Tell me how to test this function module
BAPI_CAR_PRVD_NUMBER_RANGE
if possible please provide any example based on this FM .
thanks and regards,
surya.

hi vishnu,
actually i don't now anything about this fm bcz of that reason only i am asking how to test this fm,what type of input required to test this fm
if u know please provide solution asap.
thanks and regards,
surya

Regarding Barcode dimm module

Similar Messages

Maybe you are looking for