Remove Drivers added from Sysprep's auditSystem method.

I need to replace a conflicting driver from a Windows 7 image that was added using sysprep's Pass5/auditSystem section (using 'amd64_Microsoft-Windows-PnpCutomizationsNonWinPE_neutral' > 'DriverPaths' section)
I have the replacement driver but when I attempted to run auditsystem mode in the past (for a previous driver) I was unable to get Windows to remove the driver and it would BSOD during the first setup phase (Installing Devices...) even removing the
files manually from the INF folder and the source folder would cause them to come back again. (from where? I have no clue.)
I ended up in that situation starting the image over from scratch but would like a way to avoid that when this pops up again (3rd time now)
I can find info all day on how to add drivers with this method but not remove or replace.
I have tried bot Audit and Generalize mode using both Microsoft's official sysprep and a 3rd-party one (both have the same result.)
What is the proper way to remove clean an already loaded driver? (I build these images in VMWare and transfer them to various models.)

Hi,
Try following the instructions as mentioned in the article below
https://technet.microsoft.com/en-us/library/hh825070.aspx
Regards,
D. Wu
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Similar Messages

How do you remove a folder from an itunes library once it's been added?

How do you remove a folder from an itunes library once it's been added?

When you delete the song, a menu will come up and ask you if you want to trash or keep the file. Select "keep file." It will no longer be in your song list but it will remain on your harddrive. To add it back in use the --"add to library"-- command in the drop down "File" Menu (you have to navigagte to where the song is stored on your hard drive and select it-- to add it back in.
Re: it ended up in the wrong album
If your songs are going in the wrong place go to the "Get Info" command and check the information under all the tabs (look at a song that's in the right album to see how it's listed) -- one or more of the boxes is incorrect or empty. Just put in the right information and close the info window. That should put it back in the right spot for you.

I recently removed an outlook account and now all of my calendar events are missing. The majority of them were added from my iphone 4s. How do I retrieve the events? Backing up with iCloud did not help, as I assumed it would.

I recently removed an outlook account and now all of my calendar events are missing. The majority of them were added from my iphone 4s. How do I retrieve the events? Backing up with iCloud did not help, as I assumed it would.

Outlook is a mail client for PC's (and Macs). It is not a type of account. Do you mean an "Exchange Account"?
If so, then re-add it. The calendar events live on the Exchange Server. The only way to get them back is to re-add the account to the phone. The contents of Exchange and IMAP accounts are not part of the 'backup' as they already exist elsewhere.

How to remove the recursion from the following method

Hi All,
Can u plz help me to remove the recursion from the following method.
The problem here is that recursion cann't be removed easily here as there is no any end condition.
hopefully waiting for the help....
Reema.
private FilterStatement processCustomExpressions(FilterStatement statement,
          DistinguishedName tenant, LdapDao ldapDao)
          throws NameNotFoundException,
          LDAPServerException, NamingException {
     HashMap relMap = new HashMap();
     HashMap replaceMap = new HashMap();
     Vector relVec = null;
          FilterSubExpressions expressions = statement.getExpressions();
          FilterPartIterator it = (FilterPartIterator)expressions.iterator();
          while (it.hasNext()) {
               FilterExpression e = (FilterExpression)it.next();
               if (e instanceof CustomExpression) {
                    CustomExpression ce = (CustomExpression)e;
                    try {
                         FilterExpression fe = ce.createExpression();
                         if (fe instanceof RelationshipExpression) {
                              RelationshipExpression re = (RelationshipExpression)fe;
                              it.replace(re);
                              relVec = (Vector) relMap.get(re.name);
                              if(relVec == null) {
                                   relVec = new Vector();
                                   relVec.add(re);
                              }else {
                                   relVec.add(re);
                                   it.remove();
                              relMap.put(re.name, relVec);
                         } else if (fe instanceof SystemExpression) {
     SystemExpression se = (SystemExpression)fe;
     it.replace(se);
                    } catch (FilterEvaluationException fe) {
                         traceLogger.exception(Level.DEBUG_MIN, this,
                              "processCustomExpressions(" + statement.toString() + ")", fe);
                         SystemLog.getInstance().logError(this,
                              "processCustomExpressions(" + statement.toString() + ")", fe.getMessage());
          replaceRelationshipExpressions(statement, tenant, ldapDao, relMap);
          processContainerBasedExpressions(tenant, ldapDao, relMap, replaceMap);
          FilterSubStatements statements = statement.getStatements();
          FilterStatement temp = null;
          if (statements.size() != 0) {
               FilterPartIterator iter = (FilterPartIterator)statements.iterator();
               while (iter.hasNext()) {
                    temp = (FilterStatement)iter.next();
                    temp = processCustomExpressions(temp, tenant, ldapDao);
                    iter.replace(temp);
          if(!replaceMap.isEmpty())
               return replaceContainerBasedExpressions(statement, replaceMap);
          return statement;
     }

I think one of the reasons that noone will reply to your posting is that you take it a bit too easy. First of all, please use the "code" button to format your code listings. Then it will look like this (see below) and everybody can at least read it!
private FilterStatement processCustomExpressions(FilterStatement statement,
                                                DistinguishedName tenant,
                                                LdapDao ldapDao)
        throws NameNotFoundException, LDAPServerException, NamingException {
    HashMap relMap = new HashMap();
    HashMap replaceMap = new HashMap();
    Vector relVec = null;
    FilterSubExpressions expressions = statement.getExpressions();
    FilterPartIterator it = (FilterPartIterator) expressions.iterator();
    while (it.hasNext()) {
        FilterExpression e = (FilterExpression) it.next();
        if (e instanceof CustomExpression) {
            CustomExpression ce = (CustomExpression) e;
            try {
                FilterExpression fe = ce.createExpression();
                if (fe instanceof RelationshipExpression) {
                    RelationshipExpression re = (RelationshipExpression) fe;
                    it.replace(re);
                    relVec = (Vector) relMap.get(re.name);
                    if (relVec == null) {
                        relVec = new Vector();
                        relVec.add(re);
                    else {
                        relVec.add(re);
                        it.remove();
                    relMap.put(re.name, relVec);
                else if (fe instanceof SystemExpression) {
                    SystemExpression se = (SystemExpression) fe;
                    it.replace(se);
            catch (FilterEvaluationException fe) {
                traceLogger.exception(Level.DEBUG_MIN, this,
                            "processCustomExpressions("
                            + statement.toString()
                            + ")",
                        fe);
                SystemLog.getInstance().logError(this,
                            "processCustomExpressions("
                            + statement.toString()
                            + ")",
                        fe.getMessage());
    replaceRelationshipExpressions(statement, tenant, ldapDao, relMap);
    processContainerBasedExpressions(tenant, ldapDao, relMap, replaceMap);
    FilterSubStatements statements = statement.getStatements();
    FilterStatement temp = null;
    if (statements.size() != 0) {
        FilterPartIterator iter = (FilterPartIterator) statements.iterator();
        while (iter.hasNext()) {
            temp = (FilterStatement) iter.next();
            temp = processCustomExpressions(temp, tenant, ldapDao);
            iter.replace(temp);
    if (!replaceMap.isEmpty())
        return replaceContainerBasedExpressions(statement, replaceMap);
    return statement;
}Second, when you cannot understand your own code anymore, simplify it! As far as I can see, there are two "main" processes (i.e. loops) in your method, where the second one calls the method recursively. Split the method into two. Furthermore, write a third method that processes the iterated elements and call that method from out of the loops.
I did'nt analyse your method and have no idea what it does at all. I'm merely telling my first impression.
Good luck.

Adding mail ids & Removing mail ids from the last step of process chain

Hi
Can you please guied me how to do this.
Adding mail ids & Removing mail ids from the last step of process chain.
Thanks
Subbu

You can refer the following thread.
email alert for process chain
Still I would suggest to search the forum. There will be many threads and articles on this which can help you out.

[svn:fx-trunk] 5067: In preparation for adding ASDoc version tags for Flex, remove old tags from AIR files

Revision: 5067
Author: [email protected]
Date: 2009-02-25 08:21:22 -0800 (Wed, 25 Feb 2009)
Log Message:
In preparation for adding ASDoc version tags for Flex, remove old tags from AIR files
QE Notes: None
Doc Notes: None
Bugs: -
Modified Paths:
flex/sdk/trunk/frameworks/projects/airframework/src/mx/controls/FileSystemComboBox.as
flex/sdk/trunk/frameworks/projects/airframework/src/mx/controls/FileSystemDataGrid.as
flex/sdk/trunk/frameworks/projects/airframework/src/mx/controls/FileSystemEnumerationMode .as
flex/sdk/trunk/frameworks/projects/airframework/src/mx/controls/FileSystemHistoryButton.a s
flex/sdk/trunk/frameworks/projects/airframework/src/mx/controls/FileSystemList.as
flex/sdk/trunk/frameworks/projects/airframework/src/mx/controls/FileSystemSizeDisplayMode .as
flex/sdk/trunk/frameworks/projects/airframework/src/mx/controls/FileSystemTree.as
flex/sdk/trunk/frameworks/projects/airframework/src/mx/controls/FlexNativeMenu.as
flex/sdk/trunk/frameworks/projects/airframework/src/mx/controls/HTML.as
flex/sdk/trunk/frameworks/projects/airframework/src/mx/core/FlexHTMLLoader.as
flex/sdk/trunk/frameworks/projects/airframework/src/mx/core/IWindow.as
flex/sdk/trunk/frameworks/projects/airframework/src/mx/core/Window.as
flex/sdk/trunk/frameworks/projects/airframework/src/mx/core/WindowedApplication.as
flex/sdk/trunk/frameworks/projects/airframework/src/mx/core/windowClasses/StatusBar.as
flex/sdk/trunk/frameworks/projects/airframework/src/mx/core/windowClasses/TitleBar.as
flex/sdk/trunk/frameworks/projects/airframework/src/mx/events/AIREvent.as
flex/sdk/trunk/frameworks/projects/airframework/src/mx/events/FileEvent.as
flex/sdk/trunk/frameworks/projects/airframework/src/mx/events/FlexNativeMenuEvent.as
flex/sdk/trunk/frameworks/projects/airframework/src/mx/events/FlexNativeWindowBoundsEvent .as
flex/sdk/trunk/frameworks/projects/airframework/src/mx/events/WindowExistenceEvent.as
flex/sdk/trunk/frameworks/projects/airframework/src/mx/managers/NativeDragManagerImpl.as
flex/sdk/trunk/frameworks/projects/airframework/src/mx/managers/WindowedSystemManager.as
flex/sdk/trunk/frameworks/projects/airframework/src/mx/skins/halo/ApplicationTitleBarBack groundSkin.as
flex/sdk/trunk/frameworks/projects/airframework/src/mx/skins/halo/StatusBarBackgroundSkin .as
flex/sdk/trunk/frameworks/projects/airframework/src/mx/skins/halo/WindowBackground.as
flex/sdk/trunk/frameworks/projects/airframework/src/mx/skins/halo/WindowCloseButtonSkin.a s
flex/sdk/trunk/frameworks/projects/airframework/src/mx/skins/halo/WindowMaximizeButtonSki n.as
flex/sdk/trunk/frameworks/projects/airframework/src/mx/skins/halo/WindowMinimizeButtonSki n.as
flex/sdk/trunk/frameworks/projects/airframework/src/mx/skins/halo/WindowRestoreButtonSkin .as
flex/sdk/trunk/frameworks/projects/airframework/src/mx/utils/DirectoryEnumeration.as
flex/sdk/trunk/frameworks/projects/airframework/src/mx/utils/DirectoryEnumerationMode.as

I'm also having this problem. I'm using Flash Builder 4.6, AIR 3.4 and I've made a DLL (e.g. ExtensionDll.dll) which needs to call functions in another DLL (e.g. DllUsedByExtensionDll.dll) . I've made sure my ANE is working with the ExtensionDll.dll already, so there are no issues with my actionscript code or my ANE packaging or my DLL compilation. However, once I start calling functions from the other DLL, it starts throwing me Error #3500. Even if I call this function (e.g. abc()) in ExtensionDll.dll, but I never actually use the function from actionscript, and I call another function (e.g. def()) from actionscript, the Error #3500 still appears, so it does not seem to depened on the whether the code is used or not.
It's similar to this problem.
http://stackoverflow.com/questions/9823504/how-to-use-external-dll-in-air-native-extension
Does anyone have a solution or at least a way to debug this?

[svn] 4694: Don't remove text lines from the container if it isn' t the container the lines were added to.

Revision: 4694
Author: [email protected]
Date: 2009-01-27 14:35:21 -0800 (Tue, 27 Jan 2009)
Log Message:
Don't remove text lines from the container if it isn't the container the lines were added to. When there is a state change the displayObject can be switched out from under the TextGraphic and TextBox.
QE Notes: need to add tests - will attach my test program to bug
Doc Notes:
Bugs: SDK-18923
Reviewers: Gordon
Ticket Links:
http://bugs.adobe.com/jira/browse/SDK-18923
Modified Paths:
flex/sdk/trunk/frameworks/projects/flex4/src/mx/graphics/graphicsClasses/TextBlockCompose r.as
flex/sdk/trunk/frameworks/projects/flex4/src/mx/graphics/graphicsClasses/TextFlowComposer .as

Yup, you guys pointed me in the right direction.
I changed my adjustmentListener to the following:
JScrollBar scrollBar = (JScrollBar) e.getSource();
int endLoc = document.getLength();
try {
    Rectangle end = outputArea.modelToView(endLoc);
    if (end != null) {
        int n = scrollBar.getValue() + scrollBar.getVisibleAmount();
        boolean locked = (end.y >= n && n <= (end.y + end.height));
} catch (BadLocationException ex) {
}By comparing scrollbar position with the visible rectangle of the end of the document, I can now easily tell if the user has moved the tracker back or not.
To go to the next step of automatically pausing scrolling whenever the user is moving the slider back, I also had to disable the automatic scrolling performed by DefaultCaret. Because there was no way to tell if the user was scrolling or if the output was adjusting from the adjustmentListener, I also had to flag whenever I was autoscrolling.
The end result is a JTextPane that can be appended to at all, and locked by the user by using the slider. If new data arrives, the window is not scrolled, and any text selection the user has is not cleared. Perfect!

Purchasing new iMac (27 i5), what is best method to transfer programs/files/documents from 24" iMAC? What is the best method to remove personal data from OS?

Purchasing a new iMac (27 i5), what is the best method to transfer programs/files,documents from a 24" iMac?
What is the best method to remove personal data from the 24" iMac?

Use setup assistant which is offered when you setup your new Mac. It will transfer information from a Time Machine backup, Clone or another Mac.
It's best to do this during setup to avoid issues with duplicate IDs.
Regards

Approved method of removing memory card from reader

In the past, I have just removed the memory card from the reader when I was finished with it, but I have since read that that is not good practice. The method mentioned in my book is "Click the tiny Eject button next to the card's name in the Source list, and then remove the card from the reader". The problem with that is that I have no such Eject button in my Source list, and no card name appears there, either. First of all, is it wrong to just remove the memory card without any preliminaries? Second, what do you do when there is no Eject button and no card name?

<but there is a link reading "CANON,,,DC>
what do you mean by "link"?
<....icons for 12 files appears>
are the 12 files =12photos or 12 folders?
if you see the photos, (usually DSC000143.jpg or similar) then create an empty folder on the desktop and drag & drop theses 12 photos on the empty folder. And that's it you now have uploaded the pics from card to computer.
Eject the card reader, drag to trash.
Then you can launch iPhoto.
Drag & drop that empty folder over iPhoto et vloia all your pics are imported to iPhoto.
You can now delete the empty folder to the trash.
or it's up to you where you want to put them. In iPhoto or anywhere else.
and that's it!
michel

For some reason, when my Macbook Pro starts up, all of the MS Office applications open. This was not happening when I first purchased the laptop, and I never added these apps to the startup menu. How do I remove these apps from startup?

For some reason, when my Macbook Pro starts up now, all of the MS Office applications open. This was not happening when I first purchased the laptop, and I never added these apps to the startup menu. How do I remove these apps from startup?

By default Mac apps do not close when you close the window you were working in. Unlike in Windows when you click the top right X icon in any program is closes the window and the program shuts down. On Mac OS X clicking the X in the top left hand corner only closes that windows and leave the program running in the background. If they are left open and you reboot they will restart with the system and load a window for them.

[svn:osmf:] 9866: Adding '@throws' clauses to ILayoutRenderer add/ remove target methods, and adding a 'targets(target:ILayoutTarget)' method that allows checking addition/removal validity up front.

Revision: 9866
Author:   [email protected]
Date:     2009-09-01 00:56:48 -0700 (Tue, 01 Sep 2009)
Log Message:
Adding '@throws' clauses to ILayoutRenderer add/remove target methods, and adding a 'targets(target:ILayoutTarget)' method that allows checking addition/removal validity up front.
Modified Paths:
    osmf/trunk/framework/MediaFramework/org/openvideoplayer/layout/ILayoutRenderer.as
    osmf/trunk/framework/MediaFramework/org/openvideoplayer/layout/LayoutRendererBase.as

Removing prev added keywords from main Query HUD

Can anybody help with this ....
I've been keywording a back-catalogue in Aperture over the last 2-3 days, mostly with a dedicated keywords I've prepared in the Keyword HUD, but also some misc ones. I can see that every keyword I've used to-date is logged in the Keyword section of the main library Query HUD, and it's packed with them.
Does anybody know how I can selectively remove applied keywords from the Query HUD list (not the Keyword HUD)?
(Hope that makes sense!!)

I see this as a bug and I've reported it as such.
If you start a Query HUD from a folder or project and then look at the keywords, it only shows keywords that exist among pictures within that folder or project.
If you start a Query HUD from "Library", however, it shows every single keyword ever entered, even if you are no longer using the keyword. This clutters up the HUD big time.

[SOLVED] Enabling debug for ath9k in compat-drivers-patched from AUR

Wireless card: TP-LINK TL-WN951N. lspci says that it is an Atheros AR5416 adapter [AR5008].
Some background: I'm having the same issues as the OP in this thread, which references this bug report. The problem is that I get a 2000 ms ping every 30 seconds. So 2 seconds of inactivity every 30 seconds. I have the same wireless PCI card, as well. I need to fix this, because it's making online gaming impossible. I should also note that the card is working just fine in Windows 8, however. I am using net-auto-wireless. I have tried using wicd, enabling ath9k's nohwcrypt option, toggling the card's power save, installing the latest compat-drivers-patched from the AUR, toggling different settings in my motherboard's BIOS, and removing the antennae from the card. But nothing has made a significant difference.
I think I'm really close now. I just have to disable ANI. But in order to do that, it seems that I need to enable debugging for ath9k. But this means that I need to either recompile a custom kernel, or somehow enable debug for ath9k in compat-drivers-patched from the AUR. I'd prefer the latter, as that means that I will have a more bleeding-edge driver. That, and I won't have to touch the kernel as much. What I want is described on this page. But it seems too complicated to me. Please let me explain.
I've installed things from the AUR before, as mentioned above, and have properly configured my makepkg.conf for my system. So I'd like to use the CFLAGS and such that I've set. I don't understand how everything works in the PKGBUILD; I don't have much experience with sed and awk and regular expressions, and haven't done much shell scripting at all. It seems that at some point in the PKGBUILD, I need to enable debugging for ath9k before it is compiled. Apparently on the last page I linked to, I need to add:
export CONFIG_ATH_DEBUG=y
export CONFIG_ATH9K_DEBUG=y
export CONFIG_ATH9K_DEBUGFS=y
to some config.mk file. I can only get access to the config.mk file after I install the package with pacman. I've tried adding those lines to my /etc/profile file, and checked, after a reboot, with "set", that those variables are indeed set. But the thing is, with these variables set in /etc/profile, when I run makepkg, makepkg fails with an error 2. I tried again and got the same error. I removed those lines from my /etc/profile, rebooted, tried makepkg again, and everything worked. So putting those lines in my /etc/profile is not the solution, and I feel like I'm doing something very stupid. What am I doing wrong?
I should also note that I've tried to read the wiki page on compiling a custom kernel using ABS, but it seems to just say "get your custom configuration files" and then just continue (so it assumes that I should already be familiar with the configuration part). The PKGBUILD and Creating Packages wiki pages also seem to be a little... too advanced for me at this point in time.
So how do I enable debugging for ath9k in compat-drivers-patched from the AUR? I'd prefer to stick with only editing the PKGBUILD and using makepkg, if possible.
I've really tried to search the web and the arch forums on how to fix this problem myself, but alas, it seems that I need help this time. I greatly appreciate your time for reading my long post.
UPDATE:
I've made a lot of progress. I ended up removing the AUR package with pacman by invoking "pacman -Rsn compat-drivers-patched".
Instructions for [almost] success: First, download compat-drivers-patched from AUR. Then move it to the "builds" directory (or "local", if using ABS). Extract the tarball. After the new directory is created, cd into it. Now here's the important part: run
$ makepkg -so
Then cd into src, cd into the directory inside src, then edit the config.mk file. Make sure these lines are uncommented (or created, if not already there):
export CONFIG_CFG80211_DEBUGFS=y
export CONFIG_MAC80211_DEBUGFS=y
export CONFIG_ATH_DEBUG=y
export CONFIG_ATH9K_DEBUG=y
export CONFIG_ATH9K_DEBUGFS=y
(source)
Now run "cd ../.." to go back up two directories. Now run:
$ makepkg -e
# pacman -U <file that was produced>
And I ran "mkinitcpio -p linux" just in case, but I'm not sure if that is necessary at all. I'm... not touching the kernel, right?
Now I ran:
echo 1 > /sys/kernel/debug/ieee80211/phy0/ath9k/disable_ani
But bash would say that the file or directory doesn't exist. Even if I prepend it with "sudo", I get the same results. I was only able to get the command to work if I logged in as root. I even put the line in my /etc/profile. The 2000 ms ping every 30 seconds is now GONE. HOWEVER! If I reboot and log in as a normal user, the problem is there again. If I reboot and log in as root, the problem is gone. If I then log out and then log back in as a normal user, the problem does not come back.
So really, I can avoid the problem if I first log in as root, log out, and then log back in as a normal user. But this is a great inconvenience. I would much prefer if I could just log in as a normal user right after boot, and have everything working.
Now, how do I get the command to automatically run at boot as root (without me having to log in as root), and work?
UPDATE 2:
I got it working. Putting the line in /etc/profile is not the solution. I created a custom systemd .service file.
Put this into /etc/systemd/service (name it "disable_ani.service"):
EDIT: Wow. I made a glaring typo here. It should be /etc/systemd/system/disable_ani.service
[Unit]
Description=disable_ani
[Service]
Type=oneshot
ExecStart=/bin/sh -c "echo 1 > /sys/kernel/debug/ieee80211/phy0/ath9k/disable_ani"
[Install]
WantedBy=multi-user.target
Then make sure to "sudo chmod 755 /etc/systemd/service/disable_ani.service", since root owns this file.
Then run "sudo systemctl enable disable_ani.service".
EDIT: It has been brought to my attention that there is a much simpler way than creating a custom service.
Using a tmpfile:
/etc/tmpfiles.d/disable_ani.conf
w /sys/kernel/debug/ieee80211/phy0/ath9k/disable_ani - - - - 1
Done.
Now ANI is persistently disabled between boots, even if I log in as a normal user right after boot.
Thanks for reading.
Last edited by vyu223 (2013-03-12 10:20:19)

So zsh is telling you that the command didn't work, since it claims that there is no such file or directory. I had a lot of trouble with getting the echo command to work, as well. I found that if out of these lines:
export CONFIG_CFG80211_DEBUGFS=y
export CONFIG_MAC80211_DEBUGFS=y
export CONFIG_ATH_DEBUG=y
export CONFIG_ATH9K_DEBUG=y
export CONFIG_ATH9K_DEBUGFS=y
If the first and second line above were not uncommented in the config.mk file, I couldn't leave the last line above uncommented as well, or else makepkg would fail and give me an error. So originally I had only the 3rd and 4th lines above uncommented/inserted in my config.mk. With that configuration, I could not get the echo command to work, no matter what. Have you uncommented or inserted all of the above 5 lines into your config.mk?
After making sure all of the above 5 lines were in my config.mk, the echo command still didn't work, even if I preceded the command with sudo, or entered a su session. Bash would tell me that there was no such file or directory. I found that if I actually logged out of my normal user, and then logged back into the computer as root, the command would work. If your shell does not give you any feedback (particularly, "no such file or directory"), then the command worked. In order to get the command to run every time the computer boots, I used a systemd service, so that the command is issued as root. For some reason, it doesn't work if you put the command into /etc/profile.
Oh, and it would probably be helpful to mention that for the compat-drivers-patched package from the AUR, the PKGBUILD checks to see what your _selected_drivers variable is before compilation. If you set _selected_drivers=ath9k, your compile times will be much shorter.

Removal of error from psa

hi friends
can any one tell me how can we remove an error from psa
thanks in advance
with regards
kalyan

Hi,
   Using the Error Handling function on the Update Parameters tab page in the scheduler, you can control the behavior of the BI system if data records with errors occur in the data flow with 3.x objects (use of transfer and update rules) when you are loading data using the PSA.
The system checks for data records with errors:
      in the transfer rules
      in the update rules
      when data is updated to the master data tables, text tables, or hierarchy tables
      when data is updated to the InfoCube
      when checking for referential integrity within an InfoObject against the master data tables or DataStore objects on the communication structure level.
Features
Incorrect records arising in transfer rules, update rules, when updating to a data target, or when checking for referential integrity, are highlighted and returned to the error handler. The error handler locates the original PSA records and writes the corresponding log. This function is not yet available for updating to DataStore objects.
Using the Error Handling function on the Update Parameters tab page in the scheduler, you can control how the system responds to incorrect data records.
Activities
       1.      Define how the system should react to incorrect data records
a.       No update, no reporting (default)
If errors occur, the system terminates the update of the entire data package. The request is not released for reporting. However, the system continues to check the records.
b.       Update valid records, no reporting (request red)
This option allows you to update valid data. This data is only released for reporting after the administrator checks the incorrect records that have not been updated and manually releases the request (using a QM action, that is, by setting the Overall status on the Status tab page in the monitor).
c.       Update valid records, reporting possible
Valid records can be reported immediately. Automatic follow-up actions, such as adjusting the aggregates, are also carried out.
With option a), the incorrect records are marked in red in the PSA maintenance. You can display the relevant error messages amodally, edit the records, and update the request manually. If it was not possible to write to the PSA (hierarchy or transfer method IDoc), an application log is written instead.
With options b) and c), a new request that is only updated to the PSA is formed from the incorrect records. Here you can edit the records of the new request in the PSA and start the update manually.
If errors arise when an InfoCube is updated, new requests are generated for incorrect records for each InfoCube combination. Among these requests, the incorrect records are updated to the PSA. These new requests have entered as data targets the InfoCubes for which there were incorrect records. If, for example, a record was updated to two InfoCubes by mistake, a request is generated for this record that contains both InfoCubes as data targets. In the PSA tree, the requests appear as successfully updated in the PSA. These new requests can then be triggered again for updating to the InfoCubes.
       2.      Specify the maximum number of incorrect data records that are allowed before the system terminates the load process. In the PSA, you can display the errors that have arisen up to that point. If you do not specify the maximum number of incorrect records after which termination should occur, the handling of incorrect data records is inactive and the update terminates after the first error.
       3.      Define how the BI system should react if the number of data records received by the BI system is not the same as the number of data records updated in BI.
A difference between the number of received and updated records can occur:
         in the transfer rules
         in the update rules
         when updating
Records are sorted, aggregated, or added.
If you set the No Aggregation Permitted indicator, the request is deemed incorrect if the number of received records is not the same as the number of updated records.
Regardless of this indicator, an error occurs if the number of selected records is not the same as the number of records received in the BI system.
Result
The monitor directs the user to the relevant error case and enables a direct navigation into the PSA or the respective error request.
If you want to continue processing the incorrect data records in a program that you have written yourself, you can use the method GET_ERRORS of class CL_RSSM_ERROR_HANDLER. The use of this method is documented in the RS_ERRORLOG_EXAMPLE.
To perform complex checks on data records, or to carry out specific changes to data records regularly, you can use delivered function modules (PSA-APIs) to program against a PSA table.
If you want to execute data validation with program support, select Tools ® ABAP Workbench ® Development ® ABAP Editor and create a program.
If you use transfer routines or update routines it may be necessary to read data in the PSA table afterwards.
Employee bonuses are loaded into an InfoCube and sales figures for employees are loaded into a PSA table. If an employees bonus is to be calculated in a routine in the transformation, in accordance with his/her sales, the sales must be read from the PSA table.
       1.      Call up the function module RSSM_API_REQUEST_GET to get a list of requests with request ID for a particular InfoSource of a particular type. You have the option of restricting request output using a time restriction and/or the transfer method.
You must know the request ID, as the request ID is the key that makes managing data records in the PSA possible.
       2.      With the request information received so far, and with the help of the function module, you can
         read RSAR_ODS_API_GET data records from the PSA table
         write RSAR_ODS_API_PUT changed data records in the PSA table.
RSAR_ODS_API_GET
You can call up the function module RSAR_ODS_API_GET with the list of request IDs given by the function module RSSM_API_REQUEST_GET. The function module RSAR_ODS_API_GET no longer recognizes InfoSources on the interface, rather it recognizes the request IDs instead. With the parameter I_T_SELECTIONS, you can restrict reading data records in the PSA table with reference to the fields of the transfer structure. In your program, the selections are filled and transferred to the parameter I_T_SELECTIONS.
The import parameter causes the function module to output the data records in the parameter E_T_DATA. Data output is unstructured, since the function module RSAR_ODS_API_GET works generically, and therefore does not recognize the specific structure of the PSA. You can find information on the field in the PSA table using the parameter E_T_RSFIELDTXT.
RSAR_ODS_API_PUT
After merging or checking and subsequently changing the data, you can write the altered data records into the PSA table with the function module RSAR_ODS_API_PUT. To be able to write request data into the table with the help of this function module, you have to enter the corresponding request ID. The parameter E_T_DATA contains the changed data records.

Remove ALL Images from PDF Export?

I'd like to remove ALL images from a PDF export (Indesign CS6), with the intention of having the smallest file size possible for review. All the images are Photoshop PSDs.
I have created a PDF Preset (PDF 1.7) that omits EPS, PDF and Bitmap.
That covers any PSDs that contain opaque backgrounds, i.e. are considered to be non-transparent. However, any PSDs that do NOT contain such backgrounds still appear in the exported PDF. I assume they are NOT considered to be Bitmaps?!?
I've gone for maximal compression of images (in the Preset) also just to see how small I can get the file, but it's still over a meg, and I'd really like even smaller. I live in a rural part of England where net access is painfully slow, and even a few meg of data takes far too long to upload, not to mention the constant drop-outs. Consider further that my document is likely to grow by several orders of magnitude and hopefully you can see why I'd like to sort this issue out as soon as possible.
I've not done any scripting but assume it would be trivial to hide images with a script. However, I'm not sure how such a script might know how to make visible only the images that were previously hidden by the script. Obviously I would not wish to unhide images that must stay hidden. Maybe some form of image/object tagging, if that's even possible in this product, i.e. tag them "temp hide" on first pass of the script, and so forth.
Any suggestions much appreciated.
Regards,
James

@James – to mark the container frames of the nonprinting images by a fill color, you could add the following lines of code in the for loop:
allGraphicsArray[n].nonprinting = true;
//The parent of the graphic is the container that holds it.
//We could use it to fill it with a tint of e.g. 20% of black:
allGraphicsArray[n].parent.fillColor = "Black";
allGraphicsArray[n].parent.fillTint = 20;
But this approach will add a new problem for images, that only use a portion of the holding graphic frame. Or are only partly visible due to a clipping path or a clipping mask or totally transparent areas due to transparent pixels.
Already colored backgrounds will be recolored…
@Sandee – I see the advantage of the PostScript to Distiller way in this situation, but there are two disadvantages:
1. Live transparency will be flattened (could be no issue in this use case, but you never know).
2. The gray area with the big X will be applied also to parts of the images where no pixels are present (transparent pixels in PhotoShop or TIFF files).
To work around all these issues we need a more complex script that is building a path object around the transparent parts of an image or using an applied clipping path for that purpose and fill that with a gray tint (and maybe with an X).
Here some screen shots to illustrate the problems (with or without using PostScript/Distiller):
1. Original set up:
One placed PhotoShop file with transparency stacked upon the text frame.
The image inside its holding frame is selected.
The visibility of one of its layers depicting a second chair on the left side is switched off.
2. The same setup in a different view:
3. After running the script with the two additional lines of code:
Using the PostScript method would do nearly the same plus adding a cross using the area of the selected image.
Uwe

Remove Drivers added from Sysprep's auditSystem method.

Similar Messages

Maybe you are looking for