RMA Status: Internal Error?!

]Hello all,
Is anyone else having trouble checking their return status?
Upon typing in my RMA#/Phone# and submitting, I get a page that says an Internal Error has occured.
I have been trying to check the status for about 3 days now. Same thing every time.....
Any suggestions?

I have already sent in my product for warranty service. Consequently, I do not have the serial number etc. on hand and am therefore unable to fill out the the form on the link you posted.
I still receive this error when trying to check my RMA, can you help me?
Thank you

Similar Messages

OnDemand after Source Clocked give "internal error status -88700"

Hi,
I am using Analog Input and Counter Input simultaneously with a shared internal clock source on the NI PCIe-6363
I'm running on WinXP, with NIDAQmx Driver 9.1.1f0
I start off by doing some OnDemand acquisitions and it all works.
Then I configure the task for Sample Clocked acquisitions and everything works.
Then I try to configure the task back to OnDemand using DAQmxSetSampTimingType, but when I start the task I get "DAQmx Error: An internal error occurred. Status Code : -88700"
If I ignore the error and try to acquire samples, I get a blue screen of death and the PC reboots.
DAQmx Error: An internal error occurred.
Task Name: MyTaskCI
Status Code: -88700
I tried unreserving the task, and setting the sampling timing type back to on demand, with input buffer size to 0 (also tried 1, and 1000, neither worked). I noticed that going to sample clocked mode changed various properties. I tried manually setting the data transfer mechanism back to programmed io, and disabling CI memory mapping but that did not help. Additionally I tried setting the sampling mode to finite, and number of samples per channel to 1 but that didn't help either. I also tried setting the sample clock source back to blank, but that didn't help. I am not sure if there's something else I am missing. I tried reading all the properties I thought might be getting changed by sample clocked mode, and re-applying them - but that didn't work either.
Please find attached a simplified peice of code (adapted from the NIDAQmx ANSI C Example program: ContAcq-IntClk-EveryNSamplesEvent.c) to reproduce the issue.
Your feedback is greatly appreciated.
Thanks,
hemdanw
The MathWorks
Attachments:
BufferedAICI.c ‏9 KB

Hi Falk,
Change detection does two things:
Reads digital input channels when a change occurs on a set of digital input lines.
Optionally provides a (non-periodic) trigger or clock for another task, such as digital output, analog input, analog output, or counters.
This secondary functionality is only useful when you want to detect changes on multiple input lines and treat them as if they are the same, or if you want the input lines to be sensitive to both rising and falling edges. Since you only want your digital output task to look at rising edges on a single line, you can use a PFI line instead of using change detection. The cDAQ-9172 supports PFI lines in slots 5 and 6, so move the NI 9421 to slot 5 or 6.
> Suppose I connect a button to the digital input an I want the output to be triggered when I press the button.
Okay, that partially explains what you're trying to do. How many samples do you want to output when the button is pressed?
If you want each button press to output one sample, then run "Write Dig Chan-Ext Clk.vi" with "Physical Channels" set to "cDAQ1Mod1/port0/line0:7" and "Clock Source" set to "/cDAQ1Mod5/PFI0" (with the NI 9421 in slot 5). Every time you press the button, the output will change once, assuming that the button is debounced.
If you want each button press to output a waveform containing many samples, then ideally you would be able to run "Write Dig Chan-Int Clk-Dig Start.vi", but this uses DIO triggering functionality that isn't supported by the cDAQ-9172. To emulate this functionality on the cDAQ-9172, you would need a combination of "Gen Dig Pulse-Finite-Dig Start.vi" and "Write Dig Chan-Ext Clk.vi". Start the DO task first because it will wait for the sample clock.
If the button is not debounced, you may also want to enable digital filtering on PFI0 (or build a debounce circuit). I don't know of a good example showing how to do this. Maybe someone else has an example to recommend?
Brad
Brad Keryan
NI R&D

Error sending DAV request. HTTP code 500, status 'Internal Server Error'

Hi All,
I am getting the error On SCCM R2 Environment .. on the client machine we are getting the below issue and software center
is not showing any information..
While checking on the client's DatatransferService.log.. i am getting the below issues..
Successfully sent location services HTTP failure message.
Error sending DAV request. HTTP code 500, status 'Internal Server Error'
GetDirectoryList_HTTP('http://MachineName:80/SMS_DP_SMSPKG$/7ea0b105-5592-48cd-8b8e-81777537c34f') failed with code 0x87d0027e.
i realize it because of Isapi filter issues.. can any one guide me to resolve the issues..
KJSUBBU

Hi,
In addition, I recommend you check whether you have additional Authentication methods (like ASP.NET Impersonation) enabled.
Disable the authentication method and try again.
Also, please review the link below, here is a article about troubleshoot ISAPI filter issue.
Error message when you visit a Web site that is hosted on IIS 7.0: "HTTP Error 500.0 – Internal Server Error"
http://support.microsoft.com/kb/942031
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

The server encountered an internal error () - HTTP status 500

Hi
I am working with the Tomcat 5.5 on Eclipse, and is getting the error when my servlet calls the jsp using request dispatcher, the error is:
HTTP status 500
The server encountered an internal error () that prevented it from fulfilling this request.
and the log of the exception is:
Oct 27, 2008 9:41:15 AM org.apache.catalina.core.StandardWrapperValve invoke
SEVERE: Servlet.service() for servlet Controller threw exception
java.lang.NullPointerException
at Controller.doGet(Controller.java:46)
at javax.servlet.http.HttpServlet.service(HttpServlet .java:627)
at javax.servlet.http.HttpServlet.service(HttpServlet .java:729)
at org.apache.catalina.core.ApplicationFilterChain.in ternalDoFilter(ApplicationFilterChain.java:269)
at org.apache.catalina.core.ApplicationFilterChain.do Filter(ApplicationFilterChain.java:188)
at org.apache.catalina.core.StandardWrapperValve.invo ke(StandardWrapperValve.java:213)
at org.apache.catalina.core.StandardContextValve.invo ke(StandardContextValve.java:172)
at org.apache.catalina.core.StandardHostValve.invoke( StandardHostValve.java:127)
at org.apache.catalina.valves.ErrorReportValve.invoke (ErrorReportValve.java:117)
at org.apache.catalina.core.StandardEngineValve.invok e(StandardEngineValve.java:108)
at org.apache.catalina.connector.CoyoteAdapter.servic e(CoyoteAdapter.java:174)
at org.apache.coyote.http11.Http11Processor.process(H ttp11Processor.java:875)
at org.apache.coyote.http11.Http11BaseProtocol$Http11 ConnectionHandler.processConnection(Http11BaseProt ocol.java:665)
at org.apache.tomcat.util.net.PoolTcpEndpoint.process Socket(PoolTcpEndpoint.java:528)
at org.apache.tomcat.util.net.LeaderFollowerWorkerThr ead.runIt(LeaderFollowerWorkerThread.java:81)
at org.apache.tomcat.util.threads.ThreadPool$ControlR unnable.run(ThreadPool.java:689)
at java.lang.Thread.run(Unknown Source)
and when I go to the line in the controller.java which is giving me the exception, I do not find anything wrong with it, this is the line:
RequestDispatcher dispatcher = getServletConfig().getServletContext().getRequestD ispatcher("/view.jsp");
dispatcher.forward(request, response);
Any clarifications highly appreciated.
When I debug my code, I find that the config is null just before the RequestDispatcher line. What does that mean ?
thanks.

Looks like you have a space in "D ispatcher"?
RequestDispatcher dispatcher = getServletConfig().getServletContext().getRequestD ispatcher("/view.jsp");If that's not the solution than going by your error you need to check your variable because somehow you're pointing to nothing:
java.lang.NullPointerException

Workflow internal status - Suspended - Error 401

Hi All,
I have created a simple workflow in SharePoint 2013 Designer
When I start the workflow manually, and when I click on it to see the status of workflow it shows - Internal Status - Suspended
Details are as follows :
RequestorId: 16f7a305-4450-46c2-0000-000000000000. Details: An unhandled exception occurred during the execution of the workflow instance. Exception details: System.ApplicationException: HTTP 401 {"error_description":"The server was unable to
process the request due to an internal error. For more information about the error, either turn on IncludeExceptionDetailInFaults (either from ServiceBehaviorAttribute or from the <serviceDebug> configuration behavior) on the server in order to send
the exception information back to the client, or turn on tracing as per the Microsoft .NET Framework SDK documentation and inspect the server trace logs."} {"x-ms-diagnostics":["3001000;reason=\"There has been an error authenticating
the request.\";category=\"invalid_client\""],"SPRequestGuid":["16f7a305-4450-46c2-a317-044d8178b412"],"request-id":["16f7a305-4450-46c2-a317-044d8178b412"],"X-FRAME-OPTIONS":["SAMEORIGIN"],"SPRequestDuration":["3130"],"SPIisLatency":["1"],"Server":["Microsoft-IIS\/8.5"],"WWW-Authenticate":["Bearer
realm=\"e57a12ef-af95-439f-ab00-b14d4c799098\",client_id=\"00000003-0000-0ff1-ce00-000000000000\",trusted_issuers=\"00000005-0000-0000-c000-000000000000@*,[email protected]4c799098\"","NTLM"],"X-Powered-By":["ASP.NET"],"MicrosoftSharePointTeamServices":["15.0.0.4569"],"X-Content-Type-Options":["nosniff"],"X-MS-InvokeApp":["1;
RequireReadOnly"],"Date":["Mon, 20 Apr 2015 06:57:51 GMT"]} at Microsoft.Activities.Hosting.Runtime.Subroutine.SubroutineChild.Execute(CodeActivityContext context) at System.Activities.CodeActivity.InternalExecute(ActivityInstance
instance, ActivityExecutor executor, BookmarkManager bookmarkManager) at System.Activities.Runtime.ActivityExecutor.ExecuteActivityWorkItem.ExecuteBody(ActivityExecutor executor, BookmarkManager bookmarkManager, Location resultLocation)
This is not a system account, even then it is giving the same error.
My User Profile services are also working fine, Times & Admin service are also working fine
Please help

Hi,
Please do as follows:
1.Navigate to the site that the workflow is on in SharePoint 2013 Designer.
2.Go to All Files -> Lists
3.Right click on Workflow History
4.Select Properties
5.Click on Permissions for this list under the ‘Customization’ section (This should open up the edit permissions page in the browser)
6.Break inheritance on this list by selecting Stop Inheriting Permissions in the new opened browser window
7.Use the check box next to the appropriate group (probably the visitors group) to select the group that needs updated permissions
8.Select Edit User Permissions
9.Grant the group 'Contribute' permissions
10.Select OK
More information is here:
https://sharepointcreations.wordpress.com/2014/02/18/sharepoint-2013-workflow-cancels-automatically/
If the issue still exists, please check the link below with the troubleShooting steps:
http://blog.bugrapostaci.com/2014/02/01/sharepoint-2013-workflows-are-not-working-issue/
Best Regards
TechNet Community Support
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact
[email protected]

SECSTORE Status after KERNEL Update: Internal error in secure store

We just updated the Kernel 700 to the patch 159 and, in the transaction SECSTORE, we have the error: "Internal error in secure store".
This error cause, for example, that we can't configure the STMS...
The entry id BC_INIT is missing, and when trying to add this entry using the report SECSTORE01, the system response is "Entry BC_INIT is not in the registered namespace"
What can we do to solve this problem?
Thanks in advance!

Please create an official SAP Support Ticket - and best: enable remote access to the effected system so that the problem can be analyzed, there.

OWB 11gR2 - Internal ERROR: Can not find the ACL containter

OWB 11gR2 - Internal ERROR: Can not find the ACL containter
=======================================
I am using OWB 11gR2 (11.2.0.1) on Win XP 32 bit. I have 3.23 GB RAM. OWB design center is ver slow on my desktop. We have our OWB repository is on Unix server.
We applied the patch 10270220.
We are getting
Internal ERROR: Can not find the ACL containter for object:CMPPhysicalMap@19654/id=104020/owningFCO=104020/proxyFor=(CMPPhysicalMapGen@19f99ae/id=104020/stname=null/pname=MAPPING_1/lname=MAPPING_1/status=POSTED/committed=true/persistent=true/propsLoaded=true)
What is happening here?
Thanks in helping.

We have a map with 3 sources and 1 target. The 3 sources pass through Joiner then Expression then Target.
We are getting this error, during deployment. It shows compling for awhile, then through this error.
Here is the piece from detail window:
===========
at oracle.wh.repos.pdl.security.SecurityPolicyManager.getAccessCharMapOfPrivilegeOwner(SecurityPolicyManager.java:174)
     at oracle.wh.repos.impl.foundation.CMPElement.getAccessCharMapOfPrivilegeOwner(CMPElement.java:2806)
     at oracle.wh.repos.pdl.security.OWBSecurityImpl.hasPrivilege(OWBSecurityImpl.java:914)
     at oracle.wh.repos.pdl.security.OWBSecurityImpl.internalSecurityCheck(OWBSecurityImpl.java:1542)
     at oracle.wh.repos.pdl.security.OWBSecurityImpl.securityCheck(OWBSecurityImpl.java:694)
     at oracle.wh.repos.pdl.security.SecurityModuleImpl.securityCheck(SecurityModuleImpl.java:959)
     at oracle.wh.repos.pdl.security.SecurityModuleImpl.securityCheck(SecurityModuleImpl.java:924)
     at oracle.wh.repos.pdl.dispatcher.EventDispatcherImpl.beforeReadObject(EventDispatcherImpl.java:824)
     at oracle.wh.repos.pdl.foundation.OWBRoot.beforeRead(OWBRoot.java:1785)
     at oracle.wh.repos.owbGen.CMPStringPropertyValueGen.getValue(CMPStringPropertyValueGen.java:217)
     at oracle.wh.repos.impl.properties.CMPStringPropertyValue.getValue(CMPStringPropertyValue.java:117)
     at oracle.wh.repos.impl.extended.PropertyFactory.getStringValue(PropertyFactory.java:440)
     at oracle.wh.repos.impl.extended.CMPWBPrimitiveProperty.rawStringValue(CMPWBPrimitiveProperty.java:260)
     at oracle.wh.repos.sdk.mapping.WBMapHelper.getStringProperty(WBMapHelper.java:716)
     at oracle.wh.repos.sdk.mapping.WBMapHelper.getStringProperty(WBMapHelper.java:733)
     at oracle.wh.repos.sdk.mapping.WBMapHelper.getReferencedLocations(WBMapHelper.java:1361)
     at oracle.wh.service.impl.runtime.EnvironmentUtils.getReferencedLocations(EnvironmentUtils.java:284)
     at oracle.wh.service.impl.runtime.EnvironmentUtils.getReferencedLocations(EnvironmentUtils.java:141)
     at oracle.wh.service.impl.runtime.EnvironmentUtils.getReferencedLocations(EnvironmentUtils.java:135)
     at oracle.wh.service.impl.runtime.RuntimePlatformServiceImpl.getReferencedLocations(RuntimePlatformServiceImpl.java:1238)
     at oracle.wh.ui.runtime.application.WHRuntimeCommandUtil.addConnectorLocations(WHRuntimeCommandUtil.java:477)
     at oracle.wh.ui.runtime.application.WHRuntimeCommandGenerateDeploy.getSingleDeployLocations(WHRuntimeCommandGenerateDeploy.java:3408)
     at oracle.wh.ui.runtime.application.WHRuntimeCommandGenerateDeploy.getLocationsAndNewConnectors(WHRuntimeCommandGenerateDeploy.java:3517)
     at oracle.wh.ui.runtime.application.WHRuntimeCommandGenerateDeploy.doPreDeploymentActions(WHRuntimeCommandGenerateDeploy.java:3224)
     at oracle.wh.ui.runtime.application.WHRuntimeCommandGenerateDeploy._internalDeploy(WHRuntimeCommandGenerateDeploy.java:2420)
     at oracle.wh.ui.runtime.application.WHRuntimeCommandGenerateDeploy.doDeploymentAsynch(WHRuntimeCommandGenerateDeploy.java:2117)
     at oracle.wh.ui.runtime.application.WHRuntimeCommandHandler$1.construct(WHRuntimeCommandHandler.java:1005)
     at oracle.wh.ui.runtime.SwingWorker$2.run(SwingWorker.java:124)
     at java.lang.Thread.run(Thread.java:595)
===========
Did anyone receive such errors?

Msg 8631 Internal error: Server stack limit has been reached on SQL Server 2012 from T-SQL script that runs on SQL Server 2008 R2

I have an Script mostly that is generated by SSMS which works with-out issue on SQL Server 2008, but when I attempt to run it on a new fresh install of SQL Server 2012 I get an Msg 8631. Internal error: Server stack limit has been reached. Please look for
potentially deep nesting in your query, and try to simplify it.
The script itself doesn't seem to be all that deep or nested. The script is large 2600 lines and when I remove the bulk of the 2600 lines, it does run on SQL Server 2012. I'm just really baffled why something that SQL Server generated with very
few additions/changes AND that WORKS without issue in SQL Server 2008 R2 would suddenly be invalid in SQL Server 2012
I need to know why my script which is working great on our current SQL Server 2008 R2 servers suddenly fails and won't run on an new SQL Server 2012 server. This script is used to create 'bulk' Replications on a large number of DBs saving a tremendous
amount of our time doing it the manual way.
Below is an 'condensed' version of the script which fails. I have removed around 2550 lines of specific sp_addarticle statements which are mostly just copy and pasted from what SQL Management Studio 'scripted' for me went I when through the Replication
Wizard and told it to save to script.
declare @dbname varchar(MAX), @SQL nvarchar(MAX)
declare c_dblist cursor for
select name from sys.databases WHERE name like 'dbone[_]%' order by name;
open c_dblist
fetch next from c_dblist into @dbname
while @@fetch_status = 0
begin
print @dbname
SET @SQL = 'DECLARE @dbname NVARCHAR(MAX); SET @dbname = ''' + @dbname + ''';
use ['+@dbname+']
exec sp_replicationdboption @dbname = N'''+@dbname+''', @optname = N''publish'', @value = N''true''
use ['+@dbname+']
exec ['+@dbname+'].sys.sp_addlogreader_agent @job_login = N''DOMAIN\DBServiceAccount'', @job_password = N''secret'', @publisher_security_mode = 1, @job_name = null
-- Adding the transactional publication
use ['+@dbname+']
exec sp_addpublication @publication = N'''+@dbname+' Replication'', @description = N''Transactional publication of database
'''''+@dbname+''''' from Publisher ''''MSSQLSRV\INSTANCE''''.'', @sync_method = N''concurrent'', @retention = 0, @allow_push = N''true'', @allow_pull = N''true'', @allow_anonymous = N''false'', @enabled_for_internet
= N''false'', @snapshot_in_defaultfolder = N''true'', @compress_snapshot = N''false'', @ftp_port = 21, @allow_subscription_copy = N''false'', @add_to_active_directory = N''false'', @repl_freq = N''continuous'', @status = N''active'', @independent_agent = N''true'',
@immediate_sync = N''true'', @allow_sync_tran = N''false'', @allow_queued_tran = N''false'', @allow_dts = N''false'', @replicate_ddl = 1, @allow_initialize_from_backup = N''true'', @enabled_for_p2p = N''false'', @enabled_for_het_sub = N''false''
exec sp_addpublication_snapshot @publication = N'''+@dbname+' Replication'', @frequency_type = 1, @frequency_interval = 1, @frequency_relative_interval = 1, @frequency_recurrence_factor = 0, @frequency_subday = 8,
@frequency_subday_interval = 1, @active_start_time_of_day = 0, @active_end_time_of_day = 235959, @active_start_date = 0, @active_end_date = 0, @job_login = N''DOMAIN\DBServiceAccount'', @job_password = N''secret'', @publisher_security_mode = 1
-- There are around 2400 lines roughly the same as this only difference is the tablename repeated below this one
use ['+@dbname+']
exec sp_addarticle @publication = N'''+@dbname+' Replication'', @article = N''TABLE_ONE'', @source_owner = N''dbo'', @source_object = N''TABLE_ONE'', @type = N''logbased'', @description = null, @creation_script =
null, @pre_creation_cmd = N''drop'', @schema_option = 0x000000000803509F, @identityrangemanagementoption = N''manual'', @destination_table = N''TABLE_ONE'', @destination_owner = N''dbo'', @vertical_partition = N''false'', @ins_cmd = N''CALL sp_MSins_dboTABLE_ONE'',
@del_cmd = N''CALL sp_MSdel_dboTABLE_ONE'', @upd_cmd = N''SCALL sp_MSupd_dboTABLE_ONE''
EXEC sp_executesql @SQL
SET @dbname = REPLACE(@dbname, 'dbone_', 'dbtwo_');
print @dbname
SET @SQL = 'DECLARE @dbname NVARCHAR(MAX); SET @dbname = ''' + @dbname + ''';
use ['+@dbname+']
exec sp_replicationdboption @dbname = N'''+@dbname+''', @optname = N''publish'', @value = N''true''
use ['+@dbname+']
exec ['+@dbname+'].sys.sp_addlogreader_agent @job_login = N''DOMAIN\DBServiceAccount'', @job_password = N''secret'', @publisher_security_mode = 1, @job_name = null
-- Adding the transactional publication
use ['+@dbname+']
exec sp_addpublication @publication = N'''+@dbname+' Replication'', @description = N''Transactional publication of database
'''''+@dbname+''''' from Publisher ''''MSSQLSRV\INSTANCE''''.'', @sync_method = N''concurrent'', @retention = 0, @allow_push = N''true'', @allow_pull = N''true'', @allow_anonymous = N''false'', @enabled_for_internet
= N''false'', @snapshot_in_defaultfolder = N''true'', @compress_snapshot = N''false'', @ftp_port = 21, @allow_subscription_copy = N''false'', @add_to_active_directory = N''false'', @repl_freq = N''continuous'', @status = N''active'', @independent_agent = N''true'',
@immediate_sync = N''true'', @allow_sync_tran = N''false'', @allow_queued_tran = N''false'', @allow_dts = N''false'', @replicate_ddl = 1, @allow_initialize_from_backup = N''true'', @enabled_for_p2p = N''false'', @enabled_for_het_sub = N''false''
exec sp_addpublication_snapshot @publication = N'''+@dbname+' Replication'', @frequency_type = 1, @frequency_interval = 1, @frequency_relative_interval = 1, @frequency_recurrence_factor = 0, @frequency_subday = 8,
@frequency_subday_interval = 1, @active_start_time_of_day = 0, @active_end_time_of_day = 235959, @active_start_date = 0, @active_end_date = 0, @job_login = N''DOMAIN\DBServiceAccount'', @job_password = N''secret'', @publisher_security_mode = 1
-- There are around 140 lines roughly the same as this only difference is the tablename repeated below this one
use ['+@dbname+']
exec sp_addarticle @publication = N'''+@dbname+' Replication'', @article = N''DB_TWO_TABLE_ONE'', @source_owner = N''dbo'', @source_object = N''DB_TWO_TABLE_ONE'', @type = N''logbased'', @description = null, @creation_script
= null, @pre_creation_cmd = N''drop'', @schema_option = 0x000000000803509D, @identityrangemanagementoption = N''manual'', @destination_table = N''DB_TWO_TABLE_ONE'', @destination_owner = N''dbo'', @vertical_partition = N''false''
EXEC sp_executesql @SQL
fetch next from c_dblist into @dbname
end
close c_dblist
deallocate c_dblist
George P Botuwell, Programmer

Hi George,
Thank you for your question.
I am trying to involve someone more familiar with this topic for a further look at this issue. Sometime delay might be expected from the job transferring. Your patience is greatly appreciated.
Thank you for your understanding and support.
If you have any feedback on our support, please click
here.
Allen Li
TechNet Community Support

Error 0000: internal error with Apply Transform Module

Hello:
I get an internal error message when attempting to use a previously saved data transform (namely missing value processing using MICE). What is strange is that using the previously saved model works if I feed the exact same data that was used for training
it but generates an internal error whenever I use a sample - even a 90% sample of the original. This is the output log:
Record Starts at UTC 04/02/2015 10:30:53:
Run the job:"/dll "Microsoft.Analytics.Modules.ApplyITransform.Dll, Version=6.0.0.0, Culture=neutral, PublicKeyToken=69c3241e6f0468ca;Microsoft.Analytics.Modules.ApplyITransform.Dll.ApplyITransformModule;ApplyITransform" /Output0 "..\..\Transformed dataset\Transformed dataset.dataset" /transform "..\..\Transformation\Transformation.itransform" /data "..\..\Dataset\Dataset.dataset" "
Starting Process 'C:\Resources\directory\870595a63cd0452da2f3767b831099d7.SingleNodeRuntimeCompute.Packages\AFx\6.2\DllModuleHost.exe' with arguments ' /dll "Microsoft.Analytics.Modules.ApplyITransform.Dll, Version=6.0.0.0, Culture=neutral, PublicKeyToken=69c3241e6f0468ca;Microsoft.Analytics.Modules.ApplyITransform.Dll.ApplyITransformModule;ApplyITransform" /Output0 "..\..\Transformed dataset\Transformed dataset.dataset" /transform "..\..\Transformation\Transformation.itransform" /data "..\..\Dataset\Dataset.dataset" '
[ModuleOutput] DllModuleHost Start: 1 : Program::Main
[ModuleOutput] DllModuleHost Start: 1 : DataLabModuleDescriptionParser::ParseModuleDescriptionString
[ModuleOutput] DllModuleHost S[ModuleOutput] DllModuleHost Start: 1 : DllModuleMethod::DllModuleMethod
[ModuleOutput] DllModuleHost S[ModuleOutput] DllModuleHost Start: 1 : DllModuleMethod::Execute
[ModuleOutput] DllModuleHost Start: 1 : DataLabModuleBinder::BindModuleMethod
[ModuleOutput] DllModuleHost Verbose: 1 : moduleMethodDescription Microsoft.Analytics.Modules.ApplyITransform.Dll, Version=6.0.0.0, Culture=neutral, PublicKeyToken=69c3241e6f0468ca;Microsoft.Analytics.Modules.ApplyITransform.Dll.ApplyITransformModule;ApplyITransform
[ModuleOutput] DllModuleHost Verbose: 1 : assemblyFullName Microsoft.Analytics.Modules.ApplyITransform.Dll, Version=6.0.0.0, Culture=neutral, PublicKeyToken=69c3241e6f0468ca
[ModuleOutput] DllModuleHost Start: 1 : DataLabModuleBinder::LoadModuleAssembly
[ModuleOutput] DllModuleHost Verbose: 1 : Trying to resolve assembly : Microsoft.Analytics.Modules.ApplyITransform.Dll, Version=6.0.0.0, Culture=neutral, PublicKeyToken=69c3241e6f0468ca
[ModuleOutput] DllModuleHost Verbose: 1 : Loaded moduleAssembly Microsoft.Analytics.Modules.ApplyITransform.Dll, Version=6.0.0.0, Culture=neutral, PublicKeyToken=69c3241e6f0468ca
[ModuleOutput] DllModuleHost S[ModuleOutput] DllModuleHost Verbose: 1 : moduleTypeName Microsoft.Analytics.Modules.ApplyITransform.Dll.ApplyITransformModule
[ModuleOutput] DllModuleHost Verbose: 1 : moduleMethodName ApplyITransform
[ModuleOutput] DllModuleHost Information: 1 : Module FriendlyName : Apply Transformation
[ModuleOutput] DllModuleHost Information: 1 : Module Release Status : Release
[ModuleOutput] DllModuleHost S[ModuleOutput] DllModuleHost Start: 1 : ParameterArgumentBinder::InitializeParameterValues
[ModuleOutput] DllModuleHost Verbose: 1 : parameterInfos count = 2
[ModuleOutput] DllModuleHost Verbose: 1 : parameterInfos[0] name = transform , type = Microsoft.Analytics.MachineLearning.ITransform`2[Microsoft.Numerics.Data.Local.DataTable,Microsoft.Numerics.Data.Local.DataTable]
[ModuleOutput] DllModuleHost Start: 1 : DotNetSerializationHandler::HandleArgumentString
[ModuleOutput] DllModuleHost S[ModuleOutput] DllModuleHost Verbose: 1 : parameterInfos[1] name = data , type = Microsoft.Numerics.Data.Local.DataTable
[ModuleOutput] DllModuleHost Start: 1 : DataTableDatasetHandler::HandleArgumentString
[ModuleOutput] DllModuleHost S[ModuleOutput] DllModuleHost S[ModuleOutput] DllModuleHost Verbose: 1 : Begin invoking method ApplyITransform ...
[ModuleOutput] InputDataStructure
[ModuleOutput]
[ModuleOutput] {
[ModuleOutput] "InputName":Dataset
[ModuleOutput] "Rows":385338
[ModuleOutput] "Cols":105
[ModuleOutput] "ColumnTypes":System.Nullable`1[System.Double],99,System.Nullable`1[System.Int32],5,System.String,1
[ModuleOutput] }
[ModuleOutput] DllModuleHost S[ModuleOutput] DllModuleHost Error: 1 : Program::Main encountered fatal exception: Microsoft.Analytics.Exceptions.ErrorMapping+ModuleException: Error 0000: Internal error ---> System.Reflection.TargetInvocationException: Exception has been thrown by the target of an invocation. ---> System.ArgumentException: Source array was not long enough. Check srcIndex and length, and the array's lower bounds.
Module finished after a runtime of 00:00:27.6131405 with exit code -2
Module failed due to negative exit code of -2
Record Ends at UTC 04/02/2015 10:31:38.
Experiment URL:
https://studio.azureml.net/Home/ViewWorkspace/ffac4490b5e448fa8778ceadc74a0b97?#Workspaces/Experiments/Experiment/ffac4490b5e448fa8778ceadc74a0b97.f-id.0c2caa16ad4b46b08449bcfaf4a71e57/ViewExperiment
Thanks for your help

It's pretty clear no-one at Microsoft is interested in answering this on this forum. With a paid subscription plan would I be able to get a response for these types of incidents/follow up questions? You know - so I can stop throwing money away
running experiments with modules that haven't been fixed in almost a month in hope that magically they will start to work some day...

Internal Error 7204, 6107874, 7775428, 0

I've seen that I'm not the only one faced with the same problem of Internal Error 7202 but I'm getting rather annoyed because it is now nearly impossible to update a book without a crash. Typical error message as shown below.
Error
Internal Error 7204, 6107874, 7775428, 0. FrameMaker has detected a serious problem and must quit.
A file named "c:\program files\adobe\framemaker7.2\FrameLog_07.09.10_08.44.05.txt" has been generated which contains information that may help Frame development improve the product for future releases.
Please describe your recent actions and send this, along with the generated file, to [email protected]. Due to the volume of feedback, we are unable to respond to technical questions. For support, please refer to http://www.adobe.com/support.
OK
And after OK has been pressed
Adobe FrameMaker (Structured): FrameMaker.exe - Application Error
The instruction at "0x0034199f" referenced memory at "0x00000000". The memory could not be "read".
Click on OK to terminate the program
OK
I'm using FrameMaker 7.2b158 in an XP Windows computer including all the latest patches. I've implemented some of the suggestions made in the forum like saving all documents in MIF format and then in fm-format again but nothing helps. So far I've been a quite happy user of FrameMaker because of its stability and capability of handling large documents / books but the status now is worse I ever had with any other Microsoft product. The problem is not new for me, I had it also when I used FrameMaker 7.1 and in the beginning of using FrameMaker 7.2 but it happened very infrequent.
Sometimes, if I close FrameMaker and then re-start FrameMaker again before the update process, it works but it doesn't seem to be reproducible. Please not that I'm still working on the same document, a satellite user manual, although it's now much larger (about 20 files in book with a total page count of about 2500 pages).
Of course there is also a crash log, but I cannot interpret this.
Any ideas what is going wrong?
Cheers
Tommy Strandberg
EADS Astrium GmbH / Germany

My crash is related to conditional text and XRef tags, possibly in
tables. I am using XP-pro SP2, plenty of RAM (almost 500MB available
after opening all files), plenty of swap, etc. I have all files open,
etc. This has nothing to do with generating PDF (which always seems
to work for me). I have tried doing .fm->.mif->.fm and the symptoms
did not change. Using Frame 7.1p114, non-structured.
The key is that everything works with all conditional test shown (not
hidden). Hide some conditions, click certain links and BOOM!.
When I Show all conditional text I can update the book, and all
XRefs are resolved (no errors). When I Hide some conditions and update
the book all XRefs are again resolved (no errors). But, I can reliably
crash Frame 7.1 just by double-clicking on certain links, in certain
source files, to an XREF tag located in a table (my book has 50+
files, 10+ conditional text options, thousands of XRef tags, etc.).
I can choose a specific link and confirm that the XRef tag exists and
is not hidden, both before and after hiding any text. Somehow, I think
that Frame gets confused when hiding some other tag... but even so, it
shouldn't crash.
The crash symptom indicates attempting to access address 0x0..00
(sometimes 0x0..04), which is correctly illegal (I have some sofware
experience). This is a classic software problem, caused by coding
flaws. Could be a NULL pointer (a software thing which remembers were
something is stored) or by not checking a designed-in static
limit... when the limit is exceeded the code executes into data space
(i.e. address 0x0..00). In either case (and there are other potential
causes), the root cause is a Frame implementation error; i.e. bug,
flaw, etc.
So, having said all this, I could use some advice on how to approach
Adobe about fixing this. I have a 100% reproducable problem but,
except for sending in the crash log, have not yet tried to contact
Adobe.
Advice welcome.
Thanks

Urgent: SQLException: Internal Error: Image is not in 8.1 format

Hello there,
I have never come accross such error.
Scenario
1 using JDeveloper EA1, Database 9i (9.2.0.6)
2 calling Oracle package procedure with in/out parameters.
3 Package has been imported into jDeveloper (jPublisher) with defaults settings.
4 procedure call is successfull, but when accessing out value getting this error
Code
try{
// imported package
PailinWebPolicy webPolicy=new PailinWebPolicy(conn);
System.out.println("web issue policy");
// call of package procedure both parameters are in/out
webPolicy.issuepolicy(policyData,errors,processStatus);
System.out.println("web issue policy done");
result=processStatus[0];
System.out.println("result assigned policy length "+policyData.length);
Wtpolicycore resultPolicy=policyData[0];
System.out.println("policy data assigned");
// error at accessing getPolicyno
String policyRef =resultPolicy.getPolicydata().getPolicyno();
System.out.println("policy ref assigned");
catch(SQLException e)
System.out.println("Exception "+e);
System.out.println("Exception "+e.getErrorCode()+" state "+e.getSQLState());
opus.close();
output:
web issue policy
web issue policy done
result assigned policy length 1
policy data assigned
Exception java.sql.SQLException: Internal Error: Image is not in 8.1 format
Exception 17001 state null
Any idea what might be wrong? I dont see any error on db side at all.
ferdo
Message was edited by:
frpkoo

I found similar bug reported on Metalink on April 8,2005
Bug no 4294423
Getting java.sql.SQLException: Internal Error: Image is not in 8.1 format Error Code: 17001 When running JDBC program that access many User defined Types .
But cannot find out what is the status of it.
Any idea?
ferdo

A fatal error occurred while creating an SSL client credential. The internal error state is 10011.

Need help. I have my pilot lync 2013 pool up (in coexistence with 2010 production environment) and can log into Lync 2013 environment with a lync 2010 client but am not able to with a lync 2013 client. It just prompts for password but will not
take it. I'm sseeing this on my front end server multiple times:
A fatal error occurred while creating an SSL client credential. The internal error state is 10011.
Came across this http://www.logicspot.net/index.php?id=50 and tried disabling TLS 1.2, which I did and verified but yet the issue still exists.
All my certs are good coming from internal CA. My signin logs show below but keep in mind, this works just fine if using a 2010 lync client to my lync 2013 servers. Issue only occurs when trying to connect using a lync 2013 client.
1 Login: FAIL (hr = 0x1)
this request needs authentication, trying webticket from: https://domain.com/WebTicket/WebTicketService.svc
1.1 Get-NewWebTicket: FAIL (hr = 0x1)
CLogonCredentialManager::QueryForSpecificCreds() Credential user 0x069B64A0 id=15 querying for specific credentials, credSuccess=2, targetName=Microsoft_OC1:[email protected]:specific:LAD:1
1.1.1 ExecuteWithMetadataInternal: FAIL (hr = 0x3d0000)
Executing wws method with windows auth auth, asyncContext=0A4FC348,
context: WebRequest context@ :173931816
MethodType:4
ExecutionComplete? :1
Callback@ :0A5A1864
AsyncHResult:80f10041
TargetUri:https://domain.com/WebTicket/WebTicketService.svc
OperationName:http://tempuri.org/:IWebTicketService
Error:
There was an error communicating with the endpoint at 'https://domain.com/WebTicket/WebTicketService.svc'.
The server returned HTTP status code '401 (0x191)' with text 'Unauthorized'.
The requested resource requires user authentication.
1.1.2 ExecuteWithWindowsOrNoAuthInternal: PASS
1.1.3 ExecuteWithWindowsOrNoAuthInternal: FAIL (hr = 0x3d0000)
Executing wws method with windows auth auth, asyncContext=0A4FC348,
context: WebRequest context@ :173931816
MethodType:4
ExecutionComplete? :1
Callback@ :0A5A1864
AsyncHResult:80f10041
TargetUri:https://domain.com/WebTicket/WebTicketService.svc
OperationName:http://tempuri.org/:IWebTicketService
Error:
There was an error communicating with the endpoint at 'https://domain.com/WebTicket/WebTicketService.svc'.
The server returned HTTP status code '401 (0x191)' with text 'Unauthorized'.
The requested resource requires user authentication.
1.1.4 ExecuteWithWindowsOrNoAuthInternal: FAIL (hr = 0x3d0000)
Discovery task(0A4FF830) sent to URL http://domain.com completed with hr=0x80f10045
1.1.5 ExecuteWithWindowsOrNoAuthInternal: FAIL (hr = 0x3d0000)
Executing wws method with windows auth auth, asyncContext=0A4FC348,
context: WebRequest context@ :173931816
MethodType:4
ExecutionComplete? :1
Callback@ :0A5A1864
AsyncHResult:80f10041
TargetUri:https://domain.com/WebTicket/WebTicketService.svc
OperationName:http://tempuri.org/:IWebTicketService
Error:
There was an error communicating with the endpoint at 'https://domain.com/WebTicket/WebTicketService.svc'.
The server returned HTTP status code '401 (0x191)' with text 'Unauthorized'.
The requested resource requires user authentication.
1.1.6 ExecuteWithWindowsOrNoAuthInternal: FAIL (hr = 0x3d0000)
CLogonCredentialManager::QueryForSpecificCreds() Credential user 0x069B64A0 id=15 querying for specific credentials, credSuccess=2, targetName=Microsoft_OC1:[email protected]:specific:LAD:1
Rich

Hi,
Please check the server role and Web Services for Internet Information Services (IIS) are set correctly.
For the detailed IIS configuration, please check:
http://technet.microsoft.com/en-us/library/gg412871.aspx
As Lync client 2013 attempt to query in order to perform autodiscover of the Lync registration server. First
lyncdiscoverinternal.<sipdomain> Host (A) record and then
lyncdiscover.<sipdomain> Host (A) record. If neither of these records are resolvable then the legacy DNS SRV and A record fall-back process is used. So make sure you have add the two A record in DNS server.
More details:
http://blog.schertz.name/2012/12/lync-2013-client-autodiscover/
Note: Microsoft is providing this information as a convenience to you. The sites are not controlled by Microsoft. Microsoft cannot make any representations regarding the quality, safety, or suitability of any software or information found there. Please make
sure that you completely understand the risk before retrieving any suggestions from the above link.
Best Regards,
Eason Huang
Eason Huang
TechNet Community Support

Internal error while joining a pc to domain

hi, when i want to join the pc to the domain it says "an internal error occured" and the join process fail.
i can ping the domain using fqdn and dns is working ok and the client is pointing to the appropriate dns server. also i have no anti virus installed and firewall is off. here is the netsetup.log file here.
Note: when i prestage the computer the join process is ok with no problem
can anyone help me?
08/04 17:30:45 -----------------------------------------------------------------
08/04 17:30:45 NetpValidateName: checking to see if 'vivaldi.au' is valid as type 3 name
08/04 17:30:45 NetpCheckDomainNameIsValid [ Exists ] for 'vivaldi.au' returned 0x0
08/04 17:30:45 NetpValidateName: name 'vivaldi.au' is valid for type 3
08/04 17:30:54 -----------------------------------------------------------------
08/04 17:30:54 NetpDoDomainJoin
08/04 17:30:54 NetpMachineValidToJoin: 'OMM-7687492'
08/04 17:30:54 NetpGetLsaPrimaryDomain: status: 0x0
08/04 17:30:54 NetpMachineValidToJoin: status: 0x0
08/04 17:30:54 NetpJoinDomain
08/04 17:30:54 Machine: OMM-7687492
08/04 17:30:54 Domain: vivaldi.au
08/04 17:30:54 MachineAccountOU: (NULL)
08/04 17:30:54 Account: vivaldi.au\administrator
08/04 17:30:54 Options: 0x25
08/04 17:30:54 OS Version: 5.1
08/04 17:30:54 Build number: 2600
08/04 17:30:54 ServicePack: Service Pack 3
08/04 17:30:54 NetpValidateName: checking to see if 'vivaldi.au' is valid as type 3 name
08/04 17:30:55 NetpCheckDomainNameIsValid [ Exists ] for 'vivaldi.au' returned 0x0
08/04 17:30:55 NetpValidateName: name 'vivaldi.au' is valid for type 3
08/04 17:30:55 NetpDsGetDcName: trying to find DC in domain 'vivaldi.au', flags: 0x1020
08/04 17:30:59 NetpDsGetDcName: failed to find a DC having account 'OMM-7687492$': 0x525
08/04 17:30:59 NetpDsGetDcName: found DC '\\001-002-001-204.vivaldi.au' in the specified domain
08/04 17:30:59 NetpJoinDomain: status of connecting to dc '\\001-002-001-204.vivaldi.au': 0x0
08/04 17:30:59 NetpGetLsaPrimaryDomain: status: 0x0
08/04 17:30:59 NetpGetDnsHostName: Read NV Hostname: omm-7687492
08/04 17:30:59 NetpGetDnsHostName: PrimaryDnsSuffix defaulted to DNS domain name: vivaldi.au
08/04 17:30:59 NetpLsaOpenSecret: status: 0xc0000034
08/04 17:30:59 NetpGetLsaPrimaryDomain: status: 0x0
08/04 17:30:59 NetpLsaOpenSecret: status: 0xc0000034
08/04 17:30:59 SamLookupNamesInDomain on OMM-7687492$ failed with 0xc0000073
08/04 17:30:59 NetpJoinDomain: status of setting machine password: 0x534
08/04 17:30:59 NetpJoinDomain: initiaing a rollback due to earlier errors
08/04 17:30:59 NetpLsaOpenSecret: status: 0x0
08/04 17:30:59 NetpJoinDomain: rollback: status of deleting secret: 0x0
08/04 17:30:59 NetpJoinDomain: status of disconnecting from '\\001-002-001-204.vivaldi.au': 0x0
08/04 17:30:59 NetpDoDomainJoin: status: 0x534
08/04 17:30:59 -----------------------------------------------------------------
08/04 17:30:59 NetpDoDomainJoin
08/04 17:30:59 NetpMachineValidToJoin: 'OMM-7687492'
08/04 17:30:59 NetpGetLsaPrimaryDomain: status: 0x0
08/04 17:30:59 NetpMachineValidToJoin: status: 0x0
08/04 17:30:59 NetpJoinDomain
08/04 17:30:59 Machine: OMM-7687492
08/04 17:30:59 Domain: vivaldi.au
08/04 17:30:59 MachineAccountOU: (NULL)
08/04 17:30:59 Account: vivaldi.au\administrator
08/04 17:30:59 Options: 0x27
08/04 17:30:59 OS Version: 5.1
08/04 17:30:59 Build number: 2600
08/04 17:30:59 ServicePack: Service Pack 3
08/04 17:30:59 NetpValidateName: checking to see if 'vivaldi.au' is valid as type 3 name
08/04 17:30:59 NetpCheckDomainNameIsValid [ Exists ] for 'vivaldi.au' returned 0x0
08/04 17:30:59 NetpValidateName: name 'vivaldi.au' is valid for type 3
08/04 17:30:59 NetpDsGetDcName: trying to find DC in domain 'vivaldi.au', flags: 0x1020
08/04 17:31:03 NetpDsGetDcName: failed to find a DC having account 'OMM-7687492$': 0x525
08/04 17:31:03 NetpDsGetDcName: found DC '\\001-002-001-201.vivaldi.au' in the specified domain
08/04 17:31:03 NetpJoinDomain: status of connecting to dc '\\001-002-001-201.vivaldi.au': 0x0
08/04 17:31:03 NetpGetLsaPrimaryDomain: status: 0x0
08/04 17:31:03 NetpGetDnsHostName: Read NV Hostname: omm-7687492
08/04 17:31:03 NetpGetDnsHostName: PrimaryDnsSuffix defaulted to DNS domain name: vivaldi.au
08/04 17:31:03 NetpLsaOpenSecret: status: 0xc0000034
08/04 17:31:03 NetpGetLsaPrimaryDomain: status: 0x0
08/04 17:31:03 NetpLsaOpenSecret: status: 0xc0000034
08/04 17:31:03 NetpManageMachineAccountWithSid: NetUserAdd on '\\001-002-001-201.vivaldi.au' for 'OMM-7687492$' failed: 0x54f
08/04 17:31:03 NetpJoinDomain: status of creating account: 0x54f
08/04 17:31:03 NetpJoinDomain: initiaing a rollback due to earlier errors
08/04 17:31:03 NetpLsaOpenSecret: status: 0x0
08/04 17:31:03 NetpJoinDomain: rollback: status of deleting secret: 0x0
08/04 17:31:03 NetpJoinDomain: status of disconnecting from '\\001-002-001-201.vivaldi.au': 0x0
08/04 17:31:03 NetpDoDomainJoin: status: 0x54f

repadmin /showreps shows successfull. i can attach the log or any other thing u want. time is sync between clients and domain controllers. we have 4 domain controllers and there are 2500 users in it. the problem suddenly appears since we found out
we can not join the clients to the domain at all. only the clients can be joined to the domain if the computer account is pre-created before in the domain..
You're not just simply hitting the quota limit of 10 machine accounts?
http://support.microsoft.com/kb/243327/
Enfo Zipper
Christoffer Andersson – Principal Advisor
http://blogs.chrisse.se - Directory Services Blog

Ora-00600: internal error on 11g database in windows 2007 environment

Hello , i have these problems please help me to solve it.
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:\Windows\system32>emctl status dbconsole
Environment variable ORACLE_SID not defined. Please define it.
C:\Windows\system32>set ORACLE_SID=testsid
C:\Windows\system32>emctl status dbconsole
Oracle Enterprise Manager 11g Database Control Release 11.1.0.6.0
Copyright (c) 1996, 2007 Oracle Corporation. All rights reserved.
https://local:1158/em/console/aboutApplication
Oracle Enterprise Manager 11g is not running.
Logs are generated in directory C:\app\23333941\product\11.1.0\db_3/local_testsid/sysman/log
C:\Windows\system32>sqlplus sys/@**** as sysdba
SQL*Plus: Release 11.1.0.6.0 - Production on Fri Jul 5 09:27:37 2013
Copyright (c) 1982, 2007, Oracle. All rights reserved.
SQL*Plus: Release 11.1.0.6.0 - Production
Copyright (c) 1982, 2007, Oracle. All rights reserved.
Use SQL*Plus to execute SQL, PL/SQL and SQL*Plus statements.
Usage 1: sqlplus -H | -V
    -H             Displays the SQL*Plus version and the
                   usage help.
    -V             Displays the SQL*Plus version.
Usage 2: sqlplus [ [<option>] [<logon>] [<start>] ]
<option> is: [-C <version>] [-L] [-M "<options>"] [-R <level>] [-S]
    -C <version>   Sets the compatibility of affected commands to the
                   version specified by <version>. The version has
                   the form "x.y[.z]". For example, -C 10.2.0
    -F             Enables the failover mode for a RAC environment.
    -L             Attempts to log on just once, instead of
                   reprompting on error.
    -M "<options>" Sets automatic HTML markup of output. The options
                   have the form:
                   HTML [ON|OFF] [HEAD text] [BODY text] [TABLE text]
                   [ENTMAP {ON|OFF}] [SPOOL {ON|OFF}] [PRE[FORMAT] {ON|OFF}]
    -R <level>     Sets restricted mode to disable SQL*Plus commands
                   that interact with the file system. The level can
                   be 1, 2 or 3. The most restrictive is -R 3 which
                   disables all user commands interacting with the
                   file system.
    -S             Sets silent mode which suppresses the display of
                   the SQL*Plus banner, prompts, and echoing of
                   commands.
<logon> is: (<username>[/<password>][@<connect_identifier>] | /)
              [AS SYSDBA | AS SYSOPER | AS SYSASM] | /NOLOG | [EDITION=value]
    Specifies the database account username, password and connect
    identifier for the database connection. Without a connect
    identifier, SQL*Plus connects to the default database.
    The AS SYSDBA, AS SYSOPER and AS SYSASM options are database
    administration privileges.
    <connect_identifier> can be in the form of Net Service Name
    or Easy Connect.
      @[<net_service_name> | [//]Host[:Port]/<service_name>]
        <net_service_name> is a simple name for a service that resolves
        to a connect descriptor.
        Example: Connect to database using Net Service Name and the
                 database net service name is ORCL.
           sqlplus myusername/mypassword@ORCL
        Host specifies the host name or IP address of the database
        server computer.
        Port specifies the listening port on the database server.
        <service_name> specifies the service name of the database you
        want to access.
        Example: Connect to database using Easy Connect and the
                 Service name is ORCL.
           sqlplus myusername/mypassword@Host/ORCL
    The /NOLOG option starts SQL*Plus without connecting to a
    database.
    The EDITION specifies the value for Application
    Edition
<start> is: @<URL>|<filename>[.<ext>] [<parameter> ...]
    Runs the specified SQL*Plus script from a web server (URL) or the
    local file system (filename.ext) with specified parameters that
    will be assigned to substitution variables in the script.
When SQL*Plus starts, and after CONNECT commands, the site profile
(e.g. $ORACLE_HOME/sqlplus/admin/glogin.sql) and the user profile
(e.g. login.sql in the working directory) are run. The files may
contain SQL*Plus commands.
Refer to the SQL*Plus User's Guide and Reference for more information.
C:\Windows\system32>sqlplus sys/1118@testsid as sysdba
SQL*Plus: Release 11.1.0.6.0 - Production on Fri Jul 5 09:29:03 2013
Copyright (c) 1982, 2007, Oracle. All rights reserved.
ERROR:
ORA-12154: TNS:could not resolve the connect identifier specified
Enter user-name: sysdba
Enter password:
ERROR:
ORA-01033: ORACLE initialization or shutdown in progress
Process ID: 0
Session ID: 0 Serial number: 0
Enter user-name: sys
Enter password:
ERROR:
ORA-01033: ORACLE initialization or shutdown in progress
Process ID: 0
Session ID: 0 Serial number: 0
SP2-0157: unable to CONNECT to ORACLE after 3 attempts, exiting SQL*Plus
C:\Windows\system32>sqlplus/nolog
SQL*Plus: Release 11.1.0.6.0 - Production on Fri Jul 5 09:32:59 2013
Copyright (c) 1982, 2007, Oracle. All rights reserved.
SQL> connect/as sysdba
Connected.
SQL> create table test(id number, id1 number);
create table test(id number, id1 number)
ERROR at line 1:
ORA-01109: database not open
SQL> select status from v$instance;
STATUS
MOUNTED
SQL> alter database open;
ERROR at line 1:
ORA-00600: internal error code, arguments: [kcrfr_update_nab_2], [0x51434A54],
[2], [], [], [], [], []
SQL> exit
Disconnected from Oracle Database 11g Enterprise Edition Release 11.1.0.6.0 - Production
With the Partitioning, OLAP, Data Mining and Real Application Testing options
C:\Windows\system32>startup mount
'startup' is not recognized as an internal or external command,
operable program or batch file.
C:\Windows\system32>sqlplus/nolog
SQL*Plus: Release 11.1.0.6.0 - Production on Fri Jul 5 10:05:42 2013
Copyright (c) 1982, 2007, Oracle. All rights reserved.
SQL> connect/as sysdba
Connected.
SQL> startup mount;
ORA-01081: cannot start already-running ORACLE - shut it down first
SQL> recover database;
Media recovery complete.
SQL> select GROUP#,SEQUENCE#,ARCHIVED,STATUS from v$log order by SEQUENCE#;
    GROUP# SEQUENCE# ARC STATUS
         2        539 NO INACTIVE
         3        540 NO ACTIVE
         1        541 NO CURRENT
SQL> recover database;
ORA-00283: recovery session canceled due to errors
ORA-00264: no recovery required
SQL> exit
Disconnected from Oracle Database 11g Enterprise Edition Release 11.1.0.6.0 - Production
With the Partitioning, OLAP, Data Mining and Real Application Testing options
C:\Windows\system32>sqlplus/nolog
SQL*Plus: Release 11.1.0.6.0 - Production on Fri Jul 5 10:17:10 2013
Copyright (c) 1982, 2007, Oracle. All rights reserved.
SQL> connect / as sysdba
Connected.
SQL> startup mount
ORA-01081: cannot start already-running ORACLE - shut it down first
SQL> shutdown immediate;
ORA-01109: database not open
Database dismounted.
ORACLE instance shut down.
SQL> startup;
ORACLE instance started.
Total System Global Area 313860096 bytes
Fixed Size                  1332892 bytes
Variable Size             276826468 bytes
Database Buffers           29360128 bytes
Redo Buffers                6340608 bytes
Database mounted.
Database opened.
SQL> recover database;
ORA-00283: recovery session canceled due to errors
ORA-01124: cannot recover data file 1 - file is in use or recovery
ORA-01110: data file 1:
'C:\APP\23333941\ORADATA\TEST\DATAFILE\O1_MF_SYSTEM_8XB8TY3S_.DBF'
SQL> select GROUP#,SEQUENCE#,ARCHIVED,STATUS from v$log order by SEQUENCE#;
    GROUP# SEQUENCE# ARC STATUS
         3        540 NO INACTIVE
         1        541 NO INACTIVE
         2        542 NO CURRENT
SQL> restore database;
SP2-0734: unknown command beginning "restore da..." - rest of line ignored.
SQL> recover database;
ORA-00283: recovery session canceled due to errors
ORA-01124: cannot recover data file 1 - file is in use or recovery
ORA-01110: data file 1:
'C:\APP\23333941\ORADATA\TEST\DATAFILE\O1_MF_SYSTEM_8XB8TY3S_.DBF'
SQL>
Thanks with regards Ganaa;

What happened prior that resulted in the disaster scenario that you posted/
When was the last time the DB opened with out error?
What changed since then?

APP-MRP-22075: An internal error has occurred (mrnspia, 2, 8170, )

EBS 12.1.3
Database Version 11.2.0.2
APP-MRP-22075: An internal error has occurred (mrnspia, 2, 8170, )
@ERRORTEXT Cause: The current routine encountered the specified@ERRORTEXT x Action: Contact your customer supportrepresentative.
APP-MRP-22075: An internal error has occurred (main, 19, MSCNSP, )
@ERRORTEXT Cause: The current routine encountered the specified@ERRORTEXT x Action: Contact your customer supportrepresentative.
{Code}
Steps to reproduce the issue isAdvanced Supply Chain Planner > Supply Chain Plan > Launch. Select P:BUIEH and select SP-TEST plan. Hit OK and Submit
Error Log Contents
Advanced Supply Chain Planning: Version : 12.0.0
Copyright (c) 1979, 1999, Oracle Corporation. All rights reserved.
MSCNSP module: Memory-Based Snapshot
Current system time is 23-JUL-2012 21:08:58
===================================================================
Debug Mode : Disabled
Output to Terminal : No
Argument Method : Database Fetch
Trace Mode : Disabled
===================================================================
Argument 1 (PLAN_ID) = 1026
Argument 2 (LAUNCH_CRP_PLANNER) = 2
Argument 3 (SNAPSHOT_WORKER) = 0
Argument 4 (MON_PNAME) = 0
Argument 5 (MON_REQUEST_ID) = 0
Argument 6 (SNAPSHOT_MODE) = 1
Argument 7 (SNAP_STATIC_ENTITIES) = 1
===================================================================
plan_id:1026 plan_type:1 planning_engine_type:1
Setting up flat file directories: Checking for DIR: /app/oracle/EBSCRP2/inst/apps/EBSCRP2_houebsap2/logs/appl/conc/out/data1026/
Directory is already there or can not be opened
Setting up flat file directories: Checking for mbpinput and mbpoutput directories
mbp input/output directory existing.. check it out
mbp flat file dir /app/oracle/EBSCRP2/inst/apps/EBSCRP2_houebsap2/logs/appl/conc/out/data1026/
before call to calculate plan buckets
success in calculate plan buckets
MRNSPIA: Constraine_mode :1
Planning Engine Type: ASCP Plan_type:1
The value of profile option 'MRP_RETAIN_DATES_WTIN_CAL_BOUNDARY' is Y
SELECT TO_NUMBER(TO_CHAR(MIN(calendar_date),'j')),
TO_NUMBER(TO_CHAR(MAX(calendar_date),'j'))
FROM msc_calendar_dates
WHERE calendar_code = :calendar_code
AND seq_num IS NOT NULL
AND to_number(to_char(calendar_date, 'J')) >=
to_number(to_char(sysdate, 'J')) - 365
AND exception_set_id = :exception_set_id
AND sr_instance_id = :instance_id
Loading workday calendar. Please wait ..
SELECT TO_CHAR(calendar_date, 'j')
FROM msc_calendar_dates
WHERE calendar_code = :calendar_code
AND sr_instance_id = :instance_id
AND to_number(to_char(calendar_date, 'j')) >=
to_number(to_char(sysdate, 'J')) - 365
AND exception_set_id = :exception_set_id
AND seq_num IS NOT NULL
ORDER BY calendar_date
Loading workday calendar. Please wait ...
Loading workday calendar. Please wait . 0:00
APP-MRP-22075: An internal error has occurred (mrnspia, 2, 8170, )
@ERRORTEXT Cause: The current routine encountered the specified@ERRORTEXT x Action: Contact your customer supportrepresentative.
APP-MRP-22075: An internal error has occurred (main, 19, MSCNSP, )
@ERRORTEXT Cause: The current routine encountered the specified@ERRORTEXT x Action: Contact your customer supportrepresentative.
***** End Of Program - No title available *****
Executing request completion options...
Output file size:
0
Output is not being printed because:
The print option has been disabled for this report.
Finished executing request completion options.
Concurrent program returned no reason for failure.
Exceptions posted by this request:
Concurrent Request for "Memory-Based Snapshot" has completed with error.
Concurrent request completed
Current system time is 23-JUL-2012 21:08:58

Hi;
Thanks for sharing soluiton for other forum user and thanks to Hussein Sawwan for his great posts.
PS:Please dont forget to change thread status to answered if it possible when u belive your thread has been answered, it pretend to lose time of other forums user while they are searching open question which is not answered,thanks for understanding
Regard
Helios

RMA Status: Internal Error?!

Similar Messages

Maybe you are looking for