Server recieved a message of an unititialized connection error

I received the following error in the log file (wl 6.1)
<Feb 12, 2004 3:56:22 PM EST> <Error> <ConnectionManager> <Closing:
\'weblogic.rjvm.t3.T3JVMConnection@5c6e36\' because of: \'Server received a
message over an uninitialized connection: \'JVMMessage from: \'null\' to:
\'-487357524724585114S:24.30.208.161:[80,80,443,443,80,443,-1]:starman:star\'
cmd: \'CMD_REQUEST\', QOS: \'101\', responseId: \'1\', invokableId: \'9\', flags:
\'JVMIDs Not Sent, TX Context Not Sent\', abbrev offset: \'174\'\'\'>
I searched the site and found similar but not exact matches to this.
Can someone give me some insite as to what this means or point me
to a place where I can read about it?
Thanks,
Jimmy

Similar Messages

Sun Messaging Queue (Sun MQ) Connectivity Error - recv failed

Dear Readers
I am using following code to connect to SUN MQ Server.
I only have IP Address, Port number and username password of server. JMS Server has three brokers having their own ports.
com.sun.messaging.ConnectionFactory myConnFactory = new com.sun.messaging.ConnectionFactory();
myConnFactory.setProperty(com.sun.messaging.ConnectionConfiguration.imqBrokerHostName,"19.11.12.3");
myConnFactory.setProperty(com.sun.messaging.ConnectionConfiguration.imqBrokerHostPort,"141");
myConnFactory.setProperty(com.sun.messaging.ConnectionConfiguration.imqDefaultUsername,"ad1min");
myConnFactory.setProperty(com.sun.messaging.ConnectionConfiguration.imqDefaultPassword,"ad1min");
Connection myConn = myConnFactory.createConnection();
but when i try to run this code the exception comes given below
After then i just commented Hostname and Port section and added following to it:
myConnFactory.setProperty(com.sun.messaging.ConnectionConfiguration.imqAddressList, "mq://19.11.12.3:141");
but i got same exception with slight difference:
Exception:
+15 Feb, 2013 12:32:08 PM com.sun.messaging.jmq.jmsclient.ExceptionHandler throwConnectionException+
+Exception occurred : com.sun.messaging.jms.JMSException: [C4003]: Error occurred on connection creation [19.11.12.3:141]. - cause: java.net.SocketException: Software caused connection abort: recv failed+
+WARNING: [C4003]: Error occurred on connection creation [19.11.12.3:141]. - cause: java.net.SocketException: Software caused connection abort: recv failed+
+com.sun.messaging.jms.JMSException: [C4003]: Error occurred on connection creation [19.11.12.3:141]. - cause: java.net.SocketException: Software caused connection abort: recv failed+
at com.sun.messaging.jmq.jmsclient.ExceptionHandler.throwConnectionException(ExceptionHandler.java:274)
at com.sun.messaging.jmq.jmsclient.ExceptionHandler.handleConnectException(ExceptionHandler.java:220)
at com.sun.messaging.jmq.jmsclient.PortMapperClient.readBrokerPorts(PortMapperClient.java:241)
at com.sun.messaging.jmq.jmsclient.PortMapperClient.init(PortMapperClient.java:150)
at com.sun.messaging.jmq.jmsclient.PortMapperClient.<init>(PortMapperClient.java:92)
at com.sun.messaging.jmq.jmsclient.protocol.tcp.TCPConnectionHandler.<init>(TCPConnectionHandler.java:164)
at com.sun.messaging.jmq.jmsclient.protocol.tcp.TCPStreamHandler.openConnection(TCPStreamHandler.java:135)
at com.sun.messaging.jmq.jmsclient.ConnectionInitiator.createConnection(ConnectionInitiator.java:778)
at com.sun.messaging.jmq.jmsclient.ConnectionInitiator.createConnectionNew(ConnectionInitiator.java:254)
at com.sun.messaging.jmq.jmsclient.ConnectionInitiator.createConnection(ConnectionInitiator.java:208)
at com.sun.messaging.jmq.jmsclient.ConnectionInitiator.createConnection(ConnectionInitiator.java:158)
at com.sun.messaging.jmq.jmsclient.ProtocolHandler.init(ProtocolHandler.java:816)
at com.sun.messaging.jmq.jmsclient.ProtocolHandler.<init>(ProtocolHandler.java:1529)
at com.sun.messaging.jmq.jmsclient.ConnectionImpl.openConnection(ConnectionImpl.java:2327)
at com.sun.messaging.jmq.jmsclient.ConnectionImpl.init(ConnectionImpl.java:1024)
at com.sun.messaging.jmq.jmsclient.ConnectionImpl.<init>(ConnectionImpl.java:418)
at com.sun.messaging.jmq.jmsclient.UnifiedConnectionImpl.<init>(UnifiedConnectionImpl.java:60)
at com.sun.messaging.BasicConnectionFactory.createConnection(BasicConnectionFactory.java:147)
at com.sun.messaging.BasicConnectionFactory.createConnection(BasicConnectionFactory.java:132)
at demo.JAMS.main(JAMS.java:31)
Caused by: java.net.SocketException: Software caused connection abort: recv failed
at java.net.SocketInputStream.socketRead0(Native Method)
at java.net.SocketInputStream.read(SocketInputStream.java:129)
at java.io.BufferedInputStream.fill(BufferedInputStream.java:218)
at java.io.BufferedInputStream.read(BufferedInputStream.java:237)
at com.sun.messaging.jmq.io.PortMapperTable.readLine(PortMapperTable.java:310)
at com.sun.messaging.jmq.io.PortMapperTable.read(PortMapperTable.java:266)
at com.sun.messaging.jmq.jmsclient.PortMapperClient.readBrokerPorts(PortMapperClient.java:235)
+... 17 more+
I also used imqadmin command and tried same credentials from console but i got same error
Anyone please guide me what issue is actually?
Is this server side issue? Is this access rights issue.
Tried to google it but unable to find correct solutions

>
I also used imqadmin command and tried same credentials from console but i got same errorTry using imqcmd
imqcmd query bkr -b 19.11.12.3:141
(you will be prompted for user and password)
Try running this command from your client machine and also from 19.11.12.3 (i.e. locally to the broker)
This command simply displays a few lines of info about the broker, and is a simple way to confirm that you can connect to the broker.
>
Anyone please guide me what issue is actually?
Is this server side issue? Is this access rights issue.
Tried to google it but unable to find correct solutionsCan you confirm that the broker listening on 19.11.12.3:141 has started correctly? Have you looked at the broker log? If the broker has started successfully there should be a message something like "Broker "19.11.12.3:141" ready".
Nigel

Firefox periodically shows "server not found" message for Verizon/Yahoo email. Often self corrects in 5 to 10 minutes ?

System is Windows VISTA. While on Verizon/Yahoo mail Firefox will lose the connection and shoe a "server not found" message. Explorer will connect with no problem to the email server. The problem self corrects with in 5 or 10 minutes but this may happen 5 or 6 time in a day.
Is this a Firefox problem with proxy access. Settings appear to be the same.

i forgot to mention , that when i striped this machine back down to 10.3.7 and before i re built i did do a hardware check with the original install Disks [3] and every thing came back clean.
the weird ness with the colors on window, if i pass a app like text edit over the area , the color will not cover the app but stay in the background.
when i first saw this color thing i had the preference pane out and was moving it around on screen and the colors were bleeding off of the preference pane onto the screen.
if you have any idea as to what is going on here let me know.
thank you

Disable/Hide Data connection error pop ups in InfoPath 2010

Hi All ,
I am trying to hide/Disable Error Messages Shown by data connection error. I do not want user to see the error , rather I would check through rules and query the Data source again.
Is this scenario possible at all.
For ex: I have a data connection to user profile server , if it gives and error on form load , I do not want to see the error popup instead i will query the data connection again.
Thanks and Regards,
Nandini

Hello,
what would you expect to change between the first call to the data connection and the second call?
How would you "check through rules"?
I don't think the error message can be suppressed. If you don't want to query the data connection on form load, untick the box in the data connection settings.
cheers, teylyn

JVM Connection error

Hi
I have two instances of weblogic server and Oracle database 8.1.7 server. The moment
I start my server I get the following error continuosly. Any idea on what could be
the reason for such an error?
####<Jul 4, 2002 3:53:51 PM IST> <Error> <ConnectionManager> <hsn191> <myserver>
<ExecuteThread: '11' for queue: 'default'> <> <> <000000> <Closing: 'weblogic.rjvm.t3.T3JVMConnection@6671de'
because of: 'Server received a message over an uninitialized connection: 'JVMMessage
from: 'null' to: '-7506254702625708730S:139.85.249.191:[7001,7001,7002,7002,7001,7002,-1]:mydomain:myserver'
cmd: 'CMD_REQUEST', QOS: '101', responseId: '1', invokableId: '284', flags: 'JVMIDs
Not Sent, TX Context Not Sent', abbrev offset: '20'''>
Thanks Brett

Look for .tlog files that are not empty (on your system prob under the WL
Root dir)...try deleting them or renaming them to .sav
Tom
"Brett" <[email protected]> wrote in message
news:3d242739$[email protected]..
>
Hi
I have two instances of weblogic server and Oracle database 8.1.7server. The moment
I start my server I get the following error continuosly. Any idea on whatcould be
the reason for such an error?
####<Jul 4, 2002 3:53:51 PM IST> <Error> <ConnectionManager> <hsn191><myserver>
<ExecuteThread: '11' for queue: 'default'> <> <> <000000> <Closing:'weblogic.rjvm.t3.T3JVMConnection@6671de'
because of: 'Server received a message over an uninitialized connection:'JVMMessage
from: 'null' to:'-7506254702625708730S:139.85.249.191:[7001,7001,7002,7002,7001,7002,-1]:myd
omain:myserver'
cmd: 'CMD_REQUEST', QOS: '101', responseId: '1', invokableId: '284',flags: 'JVMIDs
Not Sent, TX Context Not Sent', abbrev offset: '20'''>
Thanks Brett

Just upgraded to Lion an am discovering that I cannot send email photos from within iPhoto. Error message says bad Internet connection or server not working, when that's not the case. Never happened in Snow Leopard! Help!!!

Just upgraded to Lion an am discovering that I cannot send email photos from within iPhoto. Error message says bad Internet connection or server not working, when that's not the case. Never happened in Snow Leopard! Help!!!

what email service - Yahoo mail have been acting up lately
you can try setting Mail as your email client - it resolves this pfoblem for some people
LN

Since upgrade to iOS 7 Email error on over 100KB emails "Cannot Send Mail The message was rejected by the server because it is too large." Connecting to Exchange via Activesync

Hi,
Following the upgrade to iOS 7.0.3 on all our iPhone and iPad devices, it has been identified that when sending emails around 100KB in size and over an error message appears on the device stating “Cannot Send Mail The message was rejected by the server because it is too large.” See error message below. The send/receive limit is over 10MB so this is not the issue.
We are in an Exchange Environment using Microsoft Activesync. This issue is not evident in iOS 6. This has been tested on an iPhone 3GS running version iOS 6.1.3. We have been unable to repeat the issues seen on iOS 7 on the older OS. It is not possible to roll back to the older operating system as Apple are no longer signing the software.
We use Microsoft Active Sync to connect to our Exchange servers through a TMG. The issue is very inconsistent, some identical emails go through, some fail. This is not an issue with the send/receive limit as this is over 10MB. The error message when it fails on the TMG is Status: 413 Request Entity Too Large, which we believe is from IIS on the CAS server.
Does anyone have any suggest course of actions to take?
Many Thanks

This resolution have to attend at the server not with the ios device. My employer's mail administrator reject me to correct it from the server. As his concern is, if ither ios devices works why don't mine? So I am helpless than changing my iphone. It works fine for early versions of ios and with androids. And also one of my friends iphone4 with ios 7 (similar as mine) works too. So I guess it's something wrong with my iPhones settings. But basic question I cannot understand is it works in my phone before this ios7 upgrading. And currently working with my yahoo account too. Favourable reply expected.

TS1814 I had to restore my Ipod Touch and now I can't connect to anything on it. When it asks for my Apple ID it comes up with an error message and says that it can't connect to the server. I have checked my WiFi connection and its connected.

I have had to restore my Ipod Touch and now I can't connect to anything on it. When it asks for my Apple ID it comes up with an error message and says that it can't connect to the server. I have checked my WiFi connection and its connected.

Hi there,
I would recommend taking a look at the troubleshooting steps found in the article below.
Can't connect to the iTunes Store
http://support.apple.com/kb/ts1368
-Griff W.

My mini iPad will not connect to the internet. Getting a message that it cannot connect to the server. What is this and how do I fix it?

My mini iPad suddenly will not connect to the internet or retrieve my email. I'm getting an error message that says "cannot connect to the server". How do I fix this?

Nevermind. I found the answer from someone else's question. Thank you.

I have just switched over to iCloud and I am now getting an error message in iCal which is the following: The server is currently unable to handle the connection due to a temporary overloading or maintenance of the server. If this continues you should con

I have recently switched from MobileMe to iCloud and I now getting an error message in iCal :
"The server is currently unable to handle the connection due to a temporary overloading or maintenance of the server. If this continues you should contact the server administrator.
You may try to connect to the server again or take the account offline."
Since I am working from home and I am not on a server other than iCloud I don't understand why I am getting this message. (for 3 days). How do I fix it?

TomCT60,
Is your MacBook using Mac OS X 10.6.8 as indicated in your post? If so you will not be able to fully integrate with iCloud.
iCloud and Snow Leopard, by Roger Wilmut describes what iCloud options are available for Snow Leopard.
If you are using Lion, go to iCal>Preferences...>Accounts, and delete/re-add your iCloud CalDAV server.

Error Message: The attempt to connect to the report server failed. Check your connection information and that the report server is a compatible version. The request failed with HTTP status 404: Not Found.

I have a web page that contains a ReportViewer control. I am trying to display a report, which is an .rdl file located on the SSRS server, in this ReportViewer control. I have set the ReportPath and ReportServerUrl correctly. I am
getting an error message.
Am I suppose to use an .rdlc file rather than a .rdl file? Does the web server configuration need to use a certain account?
I am getting the following error message:
The attempt to connect to the report server failed. Check your connection information and that the report server is a compatible version.
The request failed with HTTP status 404: Not Found.

Hi bucaroov,
The error "The request failed with HTTP status 404: Not Found." means the ReportServerURL configured in the ReportViewer control is invalid.
Please follow these steps to solve the issue:
Logon the Report Server machine.
Open the Reporting Services Configuration Manager.
Copy the Report Server URL from 'Web Services URL'.
Logon the application server(in this case, it is the server that host the web page), check if we can use the URL we got from step 3 to access the Report Server. If so, please replace the ReportServerURL in the ReportViewer control with this URL. If it is
not available, could you please post the error message.
Additionaly, we don't need to provide the extension for a server report. The ReportPath should be like: /<reports folder>/<report name>
For more information, please see:
Walkthrough: Using the ReportViewer Control in Remote Mode:
http://msdn.microsoft.com/en-us/library/ms251669(VS.80).aspx
If you have any more questions, please feel free to ask.
Thanks,
Jin Chen
Jin Chen - MSFT

I recently updated to iOS 8.0 on my Ipad however when i try to agree to the new terms and conditions i get an error message saying either 'Cannot connect to server' or 'Your session has timed out please try again' what can be done to resolve this?

Hi, I recently updated to iOS 8.0 on my Ipad mini however when i try to agree to the new terms and conditions i get an error message saying either 'Cannot connect to server' or 'Your session has timed out please try again' what can be done to resolve this problem? Also i cannot download anything from the App store as a result of this.

Can you check the Object Security for the Analysis Menu and Export button and see if it is restricted?
Also, is this a Oracle DB? IF so, has the following 32 bit Oracle Client components been isntalled:
Oracle Objects for OLE
Oracle Data Provider for .NET
Oracle Providers for ASP.NET

Keep gettig this error message when trying to connect to Firefox The proxy server is refusing connections.

Redownloaded Firefox and continue to get this error message when trying to connect: The proxy server is refusing connections
Firefox is configured to use a proxy server that is refusing connections.
Check the proxy settings to make sure that they are correct.
Contact your network administrator to make sure the proxy server is
working.

Go to Options > Advanced > Network > Connection > Settings and choose "No proxy".
'''If this reply solves your problem, please click "Solved It" next to this reply when <u>signed-in</u> to the forum.'''
Not related to your question, but...
It is important that you keep IE updated. The information included with your question, indicates that you are using IE7; you should update to IE8 for your own protection. IE9 will not be made available for Windows XP.
*http://windows.microsoft.com/en-US/internet-explorer/products/ie/home

Error message when loading "The connection to the server was reset while the page was loading" I have to hit "try again and then it connects.

I get the following message when trying to connect to firefox:
"The connection to the server was reset while the page was loading." I have to click on "try again" and then it connects.

Did you check your security software (firewall)?
A possible cause is security software (firewall) that blocks or restricts Firefox without informing you about that, possibly after detecting changes (update) to the Firefox program.
Remove all rules for Firefox from the permissions list in the firewall and let your firewall ask again for permission to get full unrestricted access to internet for Firefox.
See [[Server not found]] and [[Firewalls]] and http://kb.mozillazine.org/Firewalls

HT1420 I am trying to rent a movie on my Apple TV and I keep getting the error message "Apple TV cannot connect to the server" What can I do to correct this problem?

Why does my Apple TV keep giving me the message "Apple TV cannot connect to the server" when I try and rent a movie to watch?

Hello dprice3885,
Thanks for using Apple Support Communities.
Take a look at the Wi-Fi troubleshooting since you can access the network but not the content.
Apple TV: Basic troubleshooting
http://support.apple.com/kb/HT6106
Apple TV (2nd and 3rd generation): Troubleshooting Wi-Fi networks and connections
http://support.apple.com/kb/TS4546
Have a nice day,
Mario

Server recieved a message of an unititialized connection error

Similar Messages

Maybe you are looking for