Signals in/out Control (0..3) and Enable (D..0) of PCI 1424

Hellow!!
How can I use the signal Control(0..3) and Enable(A..D) of PCI 1424 card. I have a DALSA 256 camera conected to my PCI 1424 and I need to generate a trigger and sense the frame enable signal to this camera.

The Control(0...3) lines of the PCI 1424 card are used to set camera attributes such as shutter speed and frame rate through pulse trains. These lines aren't accessable in software, but are configured in each digital camera's camera file (.icd). Once it is configured as an attribute, the attribute can be set in the Measurement & Automation Explorer (MAX) or in LabVIEW using the IMAQ Get/Set Camera Attribute VIs.
The Enable(A...D) lines are used to input a camera's sync signals. For instance, on a typical area scan camera, Enable A is used for the Frame Enable and Enable B for the Line Enable. These lines are also inaccessable from a programming environment.

Similar Messages

How to control HP 33120A and output a DC signal?

Hellow!
I'd like to control HP 33120A function generator,right now i have use the HP 33120A-WFM Config EX.VI and i can output Sin,Squart...wave,but when i try to output the DC signal,the amplitude control seems not work,what shall i do to output a DC signal and control its amplitude,Thanks!

I haven't worked with this generator or its driver, but sometimes the DC level is controlled by changing the offset instead of the amplitude. You might want to check this out.
Hope that this helps,
Bob
Bob Young - Test Engineer - Lapsed Certified LabVIEW Developer
DISTek Integration, Inc. - NI Alliance Member
mailto:[email protected]

Can I control the in and out point of a layer with a keyframe?

Hi all, I'm working in a sort of template for a series of mograph videos. Some sort of motion typography work.
The animation is always the same but the only thing that changes is the length of the video (for legibility purposes).
I was wondering if I can control the in and out points of a layer with the keyframes from another layer.
Lets say Layer's A keyframe from slider 1 position in time is the out point (plus/minus an offset would be also great) of layer B.
I've been playing with expressions on a regular basis but I don't really know where and how to write an expression like that or if it's possible.
Thanks in advance

This should probably be moved to the expression forum then.
I'm not sure I understood the details of your project but here's a basis: you can do that with an expression in the layer's time remapping property. So if you want a layer to start playing at the second keyframe on another layer, you can try something like (writing in my browser, watch for mistakes):
//   The "number" of the keyframe (first, second, third, etc)
var index = 2;
//   The layer with the keyframes
var l = {pick-whip the layer with keyframes here};
//   Just a safety, check the layer has at least enough keyframes
if (l.numKeys >= index)
     //   If yes, the new time is the difference between the keyframe's time and the current time
    max(0, l.key(index).time-time);
else
     //   Doesn't matter, let's return 0
    0;

Hi, I was working at home with my iPad, everything was going well. It went out battery and after this I am unable to connect to the wifi at home. Before getting out battery no problem, and now it sees the router signal but it is unable to connect to it.

Hi, I was working at home with my iPad, everything was going well. It went out battery and after this I am unable to connect to the wifi at home. Before getting out battery no problem, and now it sees the router signal but it is unable to connect to it.

Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
iOS 6 Wifi Problems/Fixes
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Boost Your Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
Troubleshooting a Weak Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
Wi-Fi or Bluetooth settings grayed out or dim
http://support.apple.com/kb/TS1559
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

How to sign and enable rights

I know there have been some discussions about Reader Extensions and the like, so please forgive me. I'm new to all of this and I just don't understand.
Is there a very simple, plain English guide on signing and enabling rights? My agency has finally informed me that we don't have Reader Extensions, and likely won't be getting it at any point in the near future. In order to enable user rights for people that only have Reader, is it pointless now for me to design forms in LiveCycle? Filling in forms seems to work out OK with Reader, but there are some things I can't restrict (markup, comments, etc). And there are some things I can't enable (adding attachments, for example).
As really the only guy working here that seems interested in Adobe products (IT didn't even know Reader has the ability to add attachments to a document), what are my options for restricting/enabling usage rights for forms created in LiveCycle, but without the aid of Reader Extensions? Can some/all of these rights be controlled via Acrobat X Pro? In other words, can I create a form in LiveCycle, and manage the rights enabling/restricting in Acrobat X Pro? I would imagine that would require a digital signature or certificate. I went over to Verisign and got lost. If I can do such things with a digital certificate, where and how would I go about obtaining one?
Sorry, again, for such basics. Most of the literature and discussions seem to aim at those more familiar with the products and services.

I'm sure that others on the forum would have a better answer for you but I'm going to take a stab at this.
Once you create the form in LiveCycle, open it in Adobe Acrobat Pro. Once open, select File/Save as and from the fly out menu select "Reader Extended PDF" and from that flyout menu, select "Enable Additional Features". Then it will ask you to save it again.
Once you do this, the form can be filled in with the regular Adobe Reader, the form can be saved, and the form can be used for Markup tools, such as sticky notes, redaction, digital stamps with the users' name and date, and digital signatures.
When the person selects to sign the document in the "Extended" section of Adobe Reader X, they will create a self signed signature certificate. Each signature generates it's own serial number. Unfortunately, Adobe doesn't restrict the creation of digital signatures so you can make one in your name, your dog's name, etc and yet all the signatures will validate and look absolutely legitimate.
And unfortunately, the same is true of digital stamps. All you have to do is right click the stamp and you can change the sign on id and forge another's stamp.
I hope this helped for what you are trying to do. Good luck.

How to disable and enable a Hardware Card on my Mac

Hi all,
I have a system with2 BlackMagicDesign (BMD) Decklink cards in it. One HD Extreme and one HD Extreme 3D+ card.
I use it to capture multiple video streams at once and it works perfectly. I can choose to input and output card for audio, etc...
But I have software that can use a BMD Decklink card as 3th monitor or VideoOut Monitor.
That software always chooses the HD Extreme Card, and I cant choose it manually...
I need the software to use the Decklink 3D+ card (because it has a HDMI 1.4 out and works in Stereo3D)
If I remove the second card, all works perfectly, but I want to avoid to do that...
In Windows you can easily disable hardware....
But, can we do that in MacOSX 10.7??
thx for your hrlp,
Steven.

Don't know if this will work for your specific setup or not, but SwitchResX is a unique utility for controlling video configurations (including enabling/disabling multiple monitors).

Fuzzy control using Labview and arduino

Dear all,
I have been trying to control the output of an LED using a fuzzy logic controller, based on temperature and humidity values that I receive from the DHT22 sensor via arduino in the LABVIEW setup, but the problem is, I am not sure how to set up the PWM pin of arduino for that purpose. I have used an arrangement for the setup but it has not given any LED signal so far. The VI is attached herewith. PS- I have connected the LED to pin 6 (PWM pin) of the arduino UNO board.
As far as the data acquisition part is concerned, the setup is working fine and I am being able to get the values of temp, humidity and light intensity.
Any help in this regard would be highly appreciated.
Attachments:
temhumlightctrl1.vi ‏48 KB

Just start with a simple VI commanding a PWM, and put a meter or a scope to see if the output changes. If you can't get any output there is likley a problem with your setup. If you are driving more than an LED you'll need some kind of buffer circuit or opamp to increase the current capabilities. These micros can't drive much power so if you intend on using this PWM for controlling temperature and humidity you won't be able to drive it directly.
Also be aware that your loop time is going to be relativly slow, and not deterministic. Most control systems like PIDs need to have tight timing to ensure that the system stays stable while having a decent response time. Since temperature and humidity change pretty slowly this will likely work just fine. But know that the time it takes to send a command to the Arduino, have it go out, take a sample and then send it back over serial won't be consistent.
Unofficial Forum Rules and Guidelines - Hooovahh - LabVIEW Overlord
If 10 out of 10 experts in any field say something is bad, you should probably take their opinion seriously.

Not null and enable or disable column in tabular form

Hi,
Using apex version 4.1 and working on tabular form.
ACT_COA_SEGMENT_MAS is Master table
and
ACT_SEGMENT_VALUES_MAS is detail table
I have entered 8 rows in master table and PARENT_SEGMENT_ID is column in master table which is null able. If i specified PARENT_SEGMENT_ID with value in master table then in detail table there is column PARENT_ID that should not be null and enable.
How i can enable or disable column when in master table PARENT_SEGMENT_ID column is null then in detail table PARENT_ID column should disable and vice versa.
I have created tabular form on Detail table. before insert into the tabular form Check in master table in first entry if PARENT_SEGMENT_ID is not null in first row of master table then in tabular form PARENT_ID should enable and not null able in corresponding to this first row id's lines in tabular form.
Same should check for second row in master table if PARENT_SEGMENT_ID is not null then entered rows with PARENT_ID into tabular form corresponding to 2nd id in master table should not nullable and column should enable in tabular form.
Thanks & Regards
Vedant
Edited by: Vedant on Jan 9, 2013 9:12 PM

Vedant,
You need to create you own manual tabular form and not use the wizard.
Using APEX_ITEM api you should be build you own form and you will be able to control how you wan to display the rows. (See Link [Apex Item Help|http://docs.oracle.com/cd/E37097_01/doc/doc.42/e35127/apex_item.htm#CACEEEJE] )
select case when PRIMARY_TABLE_COLUMN is null then APEX_ITEM.DISPLAY_AND_SAVE(3 , DETAIL_COLUMN ) else APEX_ITEM.TEXT(2,detail_column) end "ALIAS" from detail table
Hope that help.
Vivek

Help. I have a Google Hangout in 40mins and my sound seems to have vanished. I went to Sys Prefs and it came up with Digital Out....and the Internal Speakers option is no longer there. How do I reboot, or fix this please?

help. I have a Google Hangout in 40mins and my sound seems to have vanished. I went to Sys Prefs and it came up with Digital Out....and the Internal Speakers option is no longer there. How do I reboot, or fix this please?

There are many possible causes for this issue. Take each of the following steps that you haven't already tried. Some may not apply to your model. Back up all data before making any changes.
1. Start with the steps recommended in this support article. Don't skip any of the steps. It's the starting point for further efforts to solve the problem.
2. Make sure you have a fully up-to-date installation of OS X.
3. If you've installed an application called "Memory Clean" or any other third-party software that is supposed to "clean" or "purge" memory automatically, remove it according to the developer's instructions and restart. You should do that even if the software is not causing the problem, because it's useless.
4. Other third-party software that has been reported to interfere with sound output includes "Boom" and "Samsung Kies." If applicable, uninstall according to the developer's instructions (not by dragging something to the Trash.)
5. If an AirPlay device is selected for sound output from iTunes (or from other applications via third-party software such as "Airfoil"), deselect it.
6. Launch the application "Audio MIDI Setup" by entering the first few letters of its name in a Spotlight search and selecting it in the results (it should be at the top.) Select Built-in Output from the list on the left. If the Mute boxes are checked, uncheck them.
7. If a red light is visible in the audio-out port when sound should be playing, the internal switch is stuck in the position for digital output. You may be able to free it by inserting and removing a mini-stereo jack of the proper size. If not, the machine needs to be serviced. Inserting any kind of tool in the port may cause damage that won't be covered by the warranty.
If there's no red light, the switch may still be stuck in the headphone position. Try to free it the same way.
8. Disconnect all wired peripherals except keyboard and mouse, if applicable. If more than one display is connected, disconnect all extra ones. Restart and test.
9. If you have a MacBook Air, turn off Bluetooth and restart.
10. Start up in safe mode. Don't log in; just restart as usual when the login screen appears. When you do, make sure the words "Safe Boot" do not appear in the login screen. If they do, the system is still in safe mode and sound won't work.
11. Reset the NVRAM.
12. Reset the SMC.
13. Triple-click anywhere in the line below on this page to select it:
/Library/Preferences/Audio
Right-click or control-click the highlighted line and select
Services ▹ Reveal in Finder (or just Reveal)
from the contextual menu.* A folder should open with an item selected. Move the selected item to the Trash. You may be prompted for your administrator login password. Restart the computer and empty the Trash. Recreate your settings in the Sound preference pane.
*If you don't see the contextual menu item, copy the selected text to the Clipboard by pressing the key combination command-C. In the Finder, select
Go ▹ Go to Folder...
from the menu bar and paste into the box that opens by pressing command-V. You won't see what you pasted because a line break is included. Press return.
14. Reinstall OS X after backing up all data.
15. Make a "Genius" appointment at an Apple Store.

Can you print all the tab control's contents and include the tabs?

We are trying to generate a report that includes the contents of a tab control (graphs, text). Using the Append Control Image to Report.vi, we are only able to print out the active tab and the tab is cut off of the image. How can we generate reports that include all the tab pages and their contents and include the labeling tabs?
Thanks in advance.
Jim

I do have a workaround for makinging the prints but it looks like some sort of cropped screensave that cuts off the tabs. In my sample I was printing out 3 of the tab controls and you can see there are three by the cut off tabs. Is there a setting to allow for more of the graph and its surroundings to be "captured"?
Attachments:
Document.pdf ‏53 KB
Document (2).pdf ‏51 KB
Document (3) (2).pdf ‏58 KB

As a stockholder, I would like see the development of iTV with Retina display and integrating Siri control, internet access, and iTunes apps. This new product would be a large screen, thin wall mounted television, much like a oversided iPad.

As a stockholder, I would like see the development of iTV with Retina display and integrating Siri control, internet access, and iTunes apps. This new product would be a large screen, thin wall mounted television, much like a oversided iPad.
Do you think this product is possible?

In general theory, one now has the Edit button for their posts, until someone/anyone Replies to it. I've had Edit available for weeks, as opposed to the old forum's ~ 30 mins.
That, however, is in theory. I've posted, and immediately seen something that needed editing, only to find NO Replies, yet the Edit button is no longer available, only seconds later. Still, in that same thread, I'd have the Edit button from older posts, to which there had also been no Replies even after several days/weeks. Found one that had to be over a month old, and Edit was still there.
Do not know the why/how of this behavior. At first, I thought that maybe there WAS a Reply, that "ate" my Edit button, but had not Refreshed on my screen. Refresh still showed no Replies, just no Edit either. In those cases, I just Reply and mention the [Edit].
Also, it seems that the buttons get very scrambled at times, and Refresh does not always clear that up. I end up clicking where I "think" the right button should be and hope for the best. Seems that when the buttons do bunch up they can appear at random around the page, often three atop one another, and maybe one way the heck out in left-field.
While I'm on a role, it would be nice to be able to switch between Flattened and Threaded Views on the fly. Each has a use, and having to go to Options and then come back down to the thread is a very slow process. Jive is probably incapable of this, but I can dream.
Hunt

My imac spits out the Cd-r and I can't burn a disc

My iMac spits out the CD-R and I can't burn a disc

Hello deneye2112,
Thank you for providing the details of the burning issue you are experiencing. I found some resources that I think might help:
First, I recommend resetting the System Management Controller (SMC) on your Mac (I wasn't sure if you had a removable battery or a built in battery, so I listed the steps for both):
Resetting the SMC on Mac portables with a battery you can remove
Note: Learn about removing the battery on MacBook and MacBook Pro.
Shut down the computer.
Disconnect the MagSafe power adapter from the computer, if it's connected.
Remove the battery.
Press and hold the power button for 5 seconds.
Release the power button.
Reconnect the battery and MagSafe power adapter.
Press the power button to turn on the computer.
Resetting the SMC on portables with a battery you should not remove on your ownNote: Portable computers that have a battery you should not remove on your own include MacBook Pro (Early 2009) and later, all models of MacBook Air, and MacBook (Late 2009).
Shut down the computer.
Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected.
On the built-in keyboard, press the (left side) Shift-Control-Option keys and the power button at the same time.
Release all the keys and the power button at the same time.
Press the power button to turn on the computer.
Note: The LED on the MagSafe power adapter may change states or temporarily turn off when you reset the SMC.
You can find the full article here:
Intel-based Macs: Resetting the System Management Controller (SMC)
http://support.apple.com/kb/HT3964
If you are still having trouble with burning after that step, I recommend reviewing the section titled "Top troubleshooting tips" in the following article:
Disc Burning Quick Assist
http://support.apple.com/kb/HT1152
Thank you for posting in the Apple Support Communities.
Best,
Sheila M.

Control of brightness and contrast of HP Pavilion G4-1310au

Hello. I just got a new HP Pavilion G4-1310au. My problem is that it did not have any OS installed and so no system drivers were installed either. In the box I only got a CD that has HP manual in it and nothing else and the notebook of course, the power cord, bag, and some printed manual. I was expecting to see a System Disk CD so I could install the system drivers, but I didn't find one.
So I installed the OS and then installed the network driver which I downloaded from another computer and also the audio. My problem is that I cannot find a laucher that would help me control the brightness and contrast of the screen. I tried FN key plus F3 or F2 keys but it didn't work.
Anybody can help me how I can control the brightness and contrrast or better yet if there is a Launcher software where I can control all the features of this notebook? By the way, I don't know how to enable the bluetooth either.
Any help is much appreciated.
This question was solved.
View Solution.

You're very welcome.
You can get the latest version of the HP Support Assistant from the link below:
The download link is on the upper right side of the page (Download HP Support Assistant - Notebooks, Laptops, Netbooks)
http://www8.hp.com/us/en/campaigns/hpsupportassistant/hpsupport.html?jumpid=reg_r1002_usen_c-001_tit...

After buying a new Macbook pro and opening an iTunes Match account most of my music is grayed out on my Mac and iPhone. I have not turned on iTunes match on my iPad and all my music is fine. How do I get my music back????

After buying a new Macbook pro and opening an iTunes Match account most of my music is grayed out on my Mac and iPhone. I have not turned on iTunes match on my iPad and all my music is fine. How do I get my music back????

The most efficacious way to get your music and other personal data onto your new Mac is to restore it from the backup you made of your old computer. Once that is done you can re-enable iTM on the new Mac and your iPhone.

Mic mini to IIyama ProLite E431S: signal frequency out of range

Hi, I've just got a problem with the display (despite everything worked well together for more than a year): the screen is black, with only the following message:
Attention signal frequency out of range
H: 05.2 KHz V: 05.2 Hz
Please change signal timing
It suddenly happened yesterday, but everything was OK since I bought it, except some quick shutdown of the display from times to times
I don't know what to do, since I've got only one display so I can't modify the parameters of the mac mini
Thank goodness I also have a laptop to write this message.

Try starting in Safe mode. To do this, hold down the shift key during a restart. Hopefully you will get a working screen back. Then change the display settings to what you had before and restart normally.

Signals in/out Control (0..3) and Enable (D..0) of PCI 1424

Similar Messages

Maybe you are looking for