SRW2048 serial console is read-only
I have connected my SRW2048 to a serial port and I can see the boot process of the router but I cannot write anything, I see the login prompt but cannot login.
- I use the original cable which was shipped with the switch
- I have uses 3 differenet PCs
- I can use telnet and ssh, but I need the serial also.
It sounds like your getting to the switch just fine. The issue seems to be you don't have the password to get into it.
If that is the case, you can reset the password and login to the switch using the following steps.
The password will be admin and the username is admin.
Q. How do I recover the password of my switch?
A.If you do not know or have forgotten your password to get into the switch's configuration interface, you may try running the Password Recovery. This is a solution which allows the user login to the switch using its default username ("admin").
Performing Password Recovery (Accton Switches - SRW224P, SRW2024P)
Step 1:
Connect to the console port using terminal emulation parameters (typically 38400, 8, 0, 1, None).
Step 2:
Reboot switch by unplugging the power.
Step 3:
Hold down Ctrl U while rebooting to display Menu.
Step 4:
Select [D] Delete file.
Step 5:
Type "startup-config" (be sure that this is the ONLY file that you delete - if you delete other files, you will have to reload the firmware)
Step 6:
Now, you have erased the configuration file and you should be able to reboot and login with the default username and password.
Performing Password Recovery (Marvell Switches - SRW2016, SRW2024, SRW2048, SRW224G4, SRW248G4)
Step 1:
Connect to the console port using terminal emulation parameters (typically 38400, 8, 0, 1, None).
Step 2:
Reboot the switch by unplugging the power.
Step 3:
After viewing PASS on the screen, Press ESC on your keyboard to display the BOOTmenu.
Step 4:
Select [3] Password Recovery Procedure.
Step 5:
You can now login to the switches with the default username and password.
Note: Be sure to change the password to something you can easily remember. After rebooting, the default password will not be accessible unless you add it back to the list of passwords. The passwords will be restored to the passwords configured on the switch.
Similar Messages
-
Console Access - Read Only Permissions
How would I go about granting read-only access to a particular set of driver packages and read-write access to others? I understand the concept of security roles and scopes, but I'm not seeing a way to adjust read-only/read-write based on
scope.
Appreciate the help!The first thing that pops-up in my mind, is two security roles and two security scopes.
Scope 1 is scoped to a few driver packages and role 1 only provides read-access to driver packages. Attach these two to the administrative user/group that should have read-only access.
Scope 2 is scoped to the other driver packages and role 2 provides read-write access to driver packages. Attach these two to the administrative user/group that should have read-write access.
My Blog: http://www.petervanderwoude.nl/
Follow me on twitter: pvanderwoude -
Read only user creation for Oracle EM Console 11.1.1.5
Dear All.
I have created Read only user for Oracle EM Console.
I have followed below link to do the same
http://moshe-soa.blogspot.com/2011/09/blog-post.html.
I have noticed with read only user is that TEST button in EM Console is active means user with read only user can create a trans, in Prod scenario it is a risk.
Raised a CR with Oracle and found that it is a bug
Bug 14082464 - CANNOT DISABLE TEST/TEST WEB SERVICE BUTTON IN SOA EM COSOLE is there in Metalink.
So my question is there any way by which i can disable the TEST button in EM Conasole.
I think there are some WLST script or servlet java class available to resolve this issue.
Can any one confirm this and please suggest if any one aware of any alternative method.
Thanks,Hi, have you got any solution to this problem? I am having exact the same issue in 11.1.1.6.
-
How to create a user with read only access for ESB / BPEL Console
I need to create a user with read only access to ESB Console & BPEL Console. I have created a user
(esbreadonly) and assigned ascontrol_monitor role but user is still able to
delete services from ESB systems (such as DefaultSystem). Is there any way to
create a user that has strickly read only access to ESB Console & BPEL
Console
Thanks
Dinesh PatelCheck out this post.. I'm in the process of testing.
http://chintanblog.blogspot.com/2007/12/i-saw-numerous-people-asking-about-bpel_290.html -
Hi
For SOA Suite 10.1.3.5.1 on weblogic, Is there any way to restrict certain users to some pages in bpel console.. e.g. read only access to bpel console.
I have found articles on web regarding this but they all are for SOA Suite 10.1.3.3 (and 3.4) on Oracle app server. Article provides a hack by using servlet filters.
How to do a similar thing in SOA Suite 10.1.3.5.1 on weblogic ?
Can somebody provide step by step instructions?
ThanksHi James,
I have already seen this link and several refined versions of it but it wont work for weblogic. For example
There is no j2ee/oc4j_soa/applications/orabpel/console directory (i looked into home directory as well but could not found orabpel/console dir).
So question is where to put filter class and how to make changes in web.xml as this file is not present in j2ee/oc4j_soa/applications/orabpel/console/WEB-INF/
I checked deployments in weblogic admin console and seems BPELConsole is deployed as a module under BPELPM ear.
Any idea?
Thanks. -
Read-only user for Weblogic 6.1 sp2 console
Is there a way to restrict a user to read-only priv. on the weblogic
console? Either by using acl's or other means.
Thanks in advance,
Brown"Seb" <[email protected]> wrote in message news:3f33c3e2$[email protected]..
>
Hello,
I'd like to create a read-only user for a customer that gives him acces tothe
Console only for reading all the configuration. I don't him to modifyanything
Is there a simple way to do this ?A previous post mentioned that this is not possible in 6.1.
Brown,
This functionality is not available in 6.1. The newest version of wls
8.1 has this feature depending on the role that the user is in.
~satya -
Read only user for Weblogic Server Console (6.1)
Hello,
I'd like to create a read-only user for a customer that gives him acces to the
Console only for reading all the configuration. I don't him to modify anything
Is there a simple way to do this ?
Thanks in advance.
--Seb"Seb" <[email protected]> wrote in message news:3f33c3e2$[email protected]..
>
Hello,
I'd like to create a read-only user for a customer that gives him acces tothe
Console only for reading all the configuration. I don't him to modifyanything
Is there a simple way to do this ?A previous post mentioned that this is not possible in 6.1.
Brown,
This functionality is not available in 6.1. The newest version of wls
8.1 has this feature depending on the role that the user is in.
~satya -
Read-only access to the console
Anyone know how to set up a user to allow read-only access to the WLS console?
simon.This is not possible with WLS6.1. There is an enhancement request filed
for this issue.
- Utpal
"Simon Spruzen" <[email protected]> wrote in message
news:3c751f2c$[email protected]..
>
Anyone know how to set up a user to allow read-only access to the WLSconsole?
And does anyone know whether the console can be 'zoned'? e.g. only allowaccess
to the security part of the tree.
Thanks, WLS people,
simon. -
Read-only access to weblogic console in WL 6.1sp2
Is there a way to restrict a user to read-only priv. on the weblogic
console? Either by using acl's or other means.
Thanks in advance,
BrownBrown,
This functionality is not available in 6.1. The newest version of wls
8.1 has this feature depending on the role that the user is in.
~satya
Mr. Brown wrote:
Is there a way to restrict a user to read-only priv. on the weblogic
console? Either by using acl's or other means.
Thanks in advance,
Brown -
Read only access to Console Application ...
We have deployed development best practice examples in one WLS instance. So, all
developer can run our sample examples. All developer doesn't have admin privileges.
Some times, developer would like to get "READ ONLY " access to console application.
They can see JDBC / JMS / connection pool information.
Is it possible to allow READ ONLY Access to CONSOLE application ?
TIA
WlstechI don't think this is possible in the current release.
Kumar
"Wlstech" <[email protected]> wrote in message
news:3af30e21$[email protected]..
>
We have deployed development best practice examples in one WLS instance.So, all
developer can run our sample examples. All developer doesn't have adminprivileges.
Some times, developer would like to get "READ ONLY " access to consoleapplication.
They can see JDBC / JMS / connection pool information.
Is it possible to allow READ ONLY Access to CONSOLE application ?
TIA
Wlstech -
In wls8.1 or in wls6.1/wls7.0 ..........is there any way out to make the console
to be "READ-ONLY" ....any field or parameter that i need to set ?
any workaround may be ???
-sabgitaThis concept has been introduced in 7.0 and you'll find that a read-only
role is available called Monitor.
http://e-docs.bea.com/wls/docs70/adminguide/secsysadm.html
Patrick
"chris" <[email protected]> wrote in message
news:3d908557$[email protected]..
>
Hi all!
I would like to introduce a read-only console user on our weblogic 6.1 SP1app
server! Does anyone know how to configure such a user (respectively cananyone
give me a docu reference according to this problem)?
Is it possible anyway?
Thanks for every serious response,
Chris. -
Hi all!
I would like to introduce a read-only console user on our weblogic 6.1 SP1 app
server! Does anyone know how to configure such a user (respectively can anyone
give me a docu reference according to this problem)?
Is it possible anyway?
Thanks for every serious response,
Chris.Add the user to the Monitors group, so they have the Monitor role. This will
give them read-only access to the console.
"chris" <[email protected]> wrote in message
news:[email protected]..
>
Hi all!
I would like to introduce a read-only console user on our weblogic 6.1 SP1app
server! Does anyone know how to configure such a user (respectively cananyone
give me a docu reference according to this problem)?
Is it possible anyway?
Thanks for every serious response,
Chris. -
Read only access to Admin Console in WL 6.1
Hi,
I've seen a couple of questions already posted about this... but so far no answers!
Does anyone know how to grant read only access to the WL 6.1 Admin Console? The
supplied user "guest" doesn't seem to have any access, so I was wondering what
needs to be edited to enable this.... I've tried adding ACL's with "read" permission,
but that doesn't seem ot help.
Any thoughts would be most appreciated.
JimBrown,
This functionality is not available in 6.1. The newest version of wls
8.1 has this feature depending on the role that the user is in.
~satya
Mr. Brown wrote:
Is there a way to restrict a user to read-only priv. on the weblogic
console? Either by using acl's or other means.
Thanks in advance,
Brown -
I wan't setup for sccm 2012 read only console
i wan't setup for sccm 2012 read only console
There is role read only analyst please assign same to user or group.
-
SOA Suite read only console in 11g
Hi All,
Is there a possibility to create a user with read only role on EM in 11g? We want to create a user to monitor production environment with out having options for deploy/undeploy.
Thank You.By assigning an appropriate role to a user, you can limit his access -
http://download.oracle.com/docs/cd/E17904_01/integration.1111/e10226/appx_roles_privs.htm#BABIHDFJ
http://download.oracle.com/docs/cd/E17904_01/web.1111/e13747/secroles.htm#i1206135
Regards,
Anuj
Edited by: Anuj Dwivedi on Feb 22, 2011 9:12 PM
Maybe you are looking for
-
HT4437 i want to air play and apple tv in one device. Is that possible
I am finding it all a little confusing. I like the functionality of the airport express but wonder if the apple tv device allows the same with music and also adds the option to display on the tv? I currently use an ethernet connection to link my SON
-
SSIS: Why do columns become misaligned when importing flat files?
Hi All I am stumped with the following. When I try to load a fixed length flat file into a table, the first few thousand records load correctly but then the columns start going out of sync. Visually it looks like the data is drifting off to the right
-
Can't get Itunes to play continuously
Itubes stops playing after each song. Even in Party Shuffle not songs appear. Is there setting to change this?
-
How can i make more room on my 6-year old MacBook Pro?
How can I make more room on my 6-year old MacBook Pro? I already have an external hard drive.
-
Which framework(s)/tool(s) for a web 2.0 application ?
Hello, I'm new to Java, so excuse my stupid questions... I have to port a win32 GUI application to a web application using Java. The original application is not written with Java and is a full blown multitier win32 GUI application accessing a SQL ser