SSCC Generation

Hello All,
I am implementing HUM with SSCC generation during shipping.
I am maintaining the following settings:
SU number range : 00000000400000000000 - 00000000999999999999 (12 Digits)
HU Number Range : 00000000400000000000 - 00000000999999999999 (12 Digits)
Here when I look at the status of Number range SU number is still at Zero where has HU number range is moving along. I believe since HU management is active the HU's are being generated and stored as SU's in the warehouse, so the HU number range is used utilized.
Now I have also done the Config for SSCC generation and the Object I created has 9 numerics
000700000-000799999 since I have 16 Characters to work with i.e. 7 for ILN number and 9 for Serial number to form a SSCC leaving out the Extension digit i.e. pallet, carton and the Check digit(Which is calcuated using an Algorithm).
The question I have is once I convert the HU's into SSCC's during the final step of my of Delivery before PGI. The SSCC are being generated and Printed, but when I look up the SU's the SU is being saved with the last 12 digits(This has the config set in Conversion of storage unit numbers, I set the length of SU as 12, this was something done in the past). But when I click on it it says no SU does not exist.
Is this because my SU number is 12 characters and mu SSCC number is 18 Characters. the only problem I have is returns, how do I take the SSCC back into inventory that was retuned.
What if I had my SU number to be 18 or 20 Charactes. Would I get this error then? ?
Thanks in advance...

Hi,
if the storage location is full-WM and HU-managed, the storage unit management is always active and HU numbers are taken over as SU numbers. In all other cases HUM and SUM are independent from each other and number ranges must be set a way that they are not overlapping.
Do you use a handling unit managed storage location? (You can check this in table T001L, when xhupf is X, the sloc is handling unit managed).
Regards,
Ely
Edited by: Eleonora Juhasz on Aug 30, 2010 1:44 PM

Similar Messages

LE-HUM SSCC generation Config

Hi Experts
I am doing LE-HUM config for SSCC generaion.
Could you pls let me know what are the Configuration nodes involved/config to be done & also what config to be done wrt Check digit logic?
Quick responses will be highly appreciated.
Rgds
Ramesh

SPRO>LO>HUM>External identification>Set unique number assignment for HU identification/SSCC geenration acc to EAN 128

SSCC number with HU management

Hi Gurus,
One of our client haven't activate the HU management, and it is using SU management for his finish good. We want to generate the GS1 compliance label with SSCC number.
Is there a way here generate the SSCC number without HU management?
Cheers,

Hello Richard,
It seems that you need big custom development as there is no std provision to generate SSCC number in SAP without handling unit management. My suggestion is as below.
(1) First of all you should understand the logic of SSCC generation.
(2) After creation of TO, capture your SU number in custom table with all details of plant, sloc, WH, TO number and item number, SU number etc. You can use user exit of TO creation to update your custom table.
(3) Write a program to create new SSCC SU number by referring current SU corresponding to plant,SLOC,WH,TO number and item as per your logic and update it in another column of your custom table. This number would be your SSCC number which would corresponds to original SU. Once SSCC is created it should be printed in barcoded form. You can write program accordingly.
(4) You can create background job and run in 5-10 min interval time to update new SU as SSCC in custom table.
My purpose is to use above logic so that all std things would remin undisturbed. I might have missed out some steps which you will catch at the time of actual enhancement.
All the Best!!
Milind Chaudhari

User-exit number range SSCC-number

For some private lable products we need to use another LE_SSCC number range than for our own articles.
It is produced from the same plant and storage location.
Both the fixed ILN number range and the running number range need to be different.
Does anyone know a user-exit for handling this issue?
Best regards,
Terje

Have a look at the IMG path:
Logistics - General > Handling Unit Management > External Identification > SSCC Generation Acc. to EAN128 > Maintain SSCC Generation for Each Warehouse Number
Here you can set up:
Whse Seq.nr ILN basis nr Number range Internal External
When you can assign the external number ILN+number range to the private label products, you might be there. In WM set up under number ranges In- and external number assignment.
Hope this sets you on the right track.
Good luck
Frank

Regarding:Return process of Packaging material to Vendor

Dear SAP Experts,
When we purchase consumables material it come in packaging material from vendor.
Then we send packaging material back to vendor.But this process is mannual.
Now we want this process by system.
Please help to configure this procedure in my system.
With Regards
Mukul Kumar

hI,
I hope you are looking for packaging instruction for vendor.
As vendor will send the materiel in packaging and after delivering the material will take back the packaging material. if this is yes. Then it can be deal with Handling unit the benefit you would have of this is, harmonized way of packaging the material. And even you can create packaging instruction to vendor with weight and seize of the product .
Configuration as below for handling unit.
Go to SPRO> Logistics - General>Handling Unit Management--step1)>Define Packaging Material Types
Step 2) Define Material Group for Packaging Materials-
Step 3) Define Allowed Packaging Materials- By assigning packaging material types to the material groups for packaging materials, you define which packaging materials are allowed for packing.
Step 4) Use Handling Unit Supplements
SPRO> Logistics - General>Handling Unit Management>External Identification>Set Unique Number Assignment for HU Identification--It is only possible to indicate a storage location as HU-managed if you have set this indicator. The use of non-assigned handling units without unique number assignment is not supported
Step 2) Number Range Maintenance for HU Identification--You can maintain number ranges for number assignment for handling unit identification via number range intervals which is consists of 9 digits without overlapping
step 3) SSCC Generation Acc to EAN128
3 a) Maintain Number Range Object for SSCC-- Number range object "LE_SSCC" is provided with interval "01" and a 9-digit number length. Create the number range objects and intervals necessary for your organization and country dependent.
3 b) Maintain SSCC Generation for Each Plant / Storage Location-
4) SPRO> Logistics - General>Handling Unit Management>Automatic Packing> Packing Instructions Master Data-->Define Number Ranges for
Packing Instructions.
All your setting is in place
Then go to POP1 to create packaging instruction.
And maintain determination record using POF1 with key combination as vendor /Plant/ material, for condition type RCPT For incoming material & SHIP-Ship to party material.
Or even you can send back the returnable packaging material by using 501M > MIGO>Other Movt type--> 501M.
Hope this clear.
Rgs

HUINV01 Error

I get this message when I try to select Handling Units for inclusion in a Physical Inventory document via the HUINV01 transaction.
For object HUINV , number range interval 01 does not exist OHU_INV (message no. NR751).
I cannot find anywhere in SPRO where I can set the number range for Handling Unit Physical Inventory documents. I know I can do this using SNRO but this is not transportable. I need to move the solution from a DEV client to a QA client and won't have access to SNRO in QA.. Can anyone help where I could do this in SPRO? I have looked at all the obvious places but nothing seems to work.
Regards,
Liam.
NB: We are using Handling Units without WMS hence why the HUINV* transactions for physical inventory

I found that by using SPRO menu: Logistics General->Handling Unit Management->External Identification->SSCC Generation to EAN128->Maintain Number Range Object for SSCC.
Here I was able to enter the HUINV object and then selecting the Number Range tab, I could enter a range for the interval '01'

VL74 - Outputing E128 gives error

On VL74 (output from handling units) E128 output it shown.
Certain E128 outputs works fine whilst other do not work as follows :-
When using preview the following message is returned :-
Preview = Output could not be displayed (it may not be complete)
Message no. VN069
When trying to output the log shows the following error :-
Note: Log not from current processing run
Processing log for program RLE_EAN128_LABEL routine ENTRY
Check digit for value 1000013650 is incorrect -- 1000013656 would be correct
Message no. LE_SHP_BF_BARCODE016
Diagnosis
In certain circumstances, the handling unit does not have a SSCC number.
Procedure
Check in Customizing for the handling unit whether a SSCC number was assigned during number assignment to the packaging material type.
R/3 Customizing IMG -> Logistics - General -> Handling Unit Management -> Basics -> Define Packaging Material Types
Regards.
Phil.

Hi
Make sure you have maintained correct settings in below IMG:-
1) SSCC Generation Acc. to EAN128-->Maintain SSCC Generation for Each Plant / Storage Location
2) HUM>Basics>Technical Basics
3) And maintain the settings for Output determination for HU in NACE transaction
Rgds
Ramesh
Edited by: ramesh04 on Nov 29, 2010 5:40 PM

Error while activating Inbound Delivery Notification

Hi,
I have created and Inbound delivery in ERP, the material is batch managed and packed with HU. Once saved on ERP system, I find the Inbound Delivery Notification in SCM EWM system with HU, material and batch number appearing. Up to this point all good.
However, when I am trying to hit the button 'Activate' so that I can create Inbound delivery, system comes up with error message - 'Please specify an external number range' (message NR753) I have no idea where it's coming from.
For further information - I am using standard Doc Type INB with Doc Cat. PDI and it's assigned with an Internal Number Range.
What's missing?
I help will be rewarded.
Thanks,
Amit

Thanks Virendra,
You have pointed to the right direction. Basically, without checking for the posts here, which are really helpful, I went to system one more time only to find that I have made a configuration error. I am just sharing if anyone else in future faces same situation, he/she can be benefited out of it.
In EWM system - I had created number range with transaction SNRO for object /SCWM/SSCC putting 01 (from 1 - 1999999) as internal and 02 (from 2000000 - 2999999) as external number range.
In EWM system - I had assigned the number range in following place:
Extended Warehouse Management > Cross Process Settings > Handling Units > External Identification > SSCC Generation Acc. to EAN128 > Maintain SSCC Generation for Each Warehouse Number
In ERP system - I had created number range with SNRO for object LE_SSCC with same attributes as above. i.e. 01 as internal and 02 as external.
Now when I packed the inbound delivery in ERP system, I used packaging material for which the number range is internal (i.e. 01) and it created HU with SSCC number. Up to this all were good. But when the same HU transferred from ERP to EWM system, SAP treated the HU number coming from ERP system as external HU number (which is logical) but it was looking at number range 02 (since it was marked as external) but was failing to match as the allowed numbers doesn't fit along with the number transferred from ERP system. Hence it was giving error.
As a solution I declared 01 as external and 02 as internal and also inverted the number range assignment for SSCC generation in EWM system.
It created Inbound Delivery successfully.
Thanks all of you for helping on it.
Cheers,
Amit

HUM in IM Location

Hello All,
This questions only involves Outbound Deliveries.
I am trying to implement HUM at an IM location.
I am trying to generate SSCC when I pack the delivery and it is letting me do so.
I maintained the config LO->HUM->External Identification-> SSCC generation Acc to EAN 128 -> Maintain SSCC generation for each plant/Storage location. This is allowing me to generate SSCC numbers at a St location level.
But now I am looking at this SAP documentation that says,
You can use all the functions from Inventory Management. The following are the exceptions:
The EAN128 functionality is not supported.
http://help.sap.com/saphelp_erp60_sp/helpdata/en/1f/7f6d36f74c7505e10000009b38f839/frameset.htm
Can anyone please explain what this means?
Thank You,
Rakesh Yarlagadda

You can generate SSCC on HU's that are maintained even at IM locations. So not sure what SAP is trying to say.

How an SSCC number gets generated

Hi Gurus,
I am now learning HUM. Actually I dont have access to client system. I am working on sandbox and I want to know how an SSCC number gets generated. I checked Number range object LE_SSCC. I did not not understand the relevence because in LE_SSCC, current number is 290 and the Internal HU number is 1500. Number range object HU_VEKP is working fine with internal HU Number. The SSCC numbers are incremented some times with 7 and some times with 17. No where I could see the source settings for this.
I hope that SSCC Number is copied from the box sent by vendor through bar code readear. If that is the case it should be randomly changing. There should not be any fixed increment. What is the guarentee that it is not repeated?
Please throw some light on SSCC Number generation.

Hi Nagesh,
You define the number range in t-code SNRO. You can define an external number range there for you vendor received SSCC numbers. The skipping in the number range can occur baseed upon what is in the number range buffer in SAP. When you log in you are assigned numbers from the number range and when someon else signs in they are assigned numbers from the range. These numbers may not be sequential.
Regards,
Steve

Open vi error for report generation toolkt

Originally it works fine.
Now I upgrade to win7, LV9 and office2010.
To open the old program by 8.6.1, I reinstalled LV 8.6.1 and report generation toolkit.
But still got the error as attached.
Any suggestion, thanks.
Attachments:
ss.png ‏184 KB

1. MS Office 2010 is not yet supported, since it's still just a beta. I believe there are couple of changes that Microsoft make, and it could cause a problem.
2. LabVIEW 8.6.1, and all its toolkit is not supported on Windows 7. This could cause a problkem also.
In conclusion, you should use LabVIEW 2009, Report Generation Toolkit 2009, Windows 7, and downgrade office to XP, 2003 or 2007.
More information: http://digital.ni.com/public.nsf/allkb/C9408B9F08D711E786256F3300701D01

1st Generation iPod Touch No Longer Recognized by Windows 7 PC

I have a 1st generation iPod Touch (no camera) that can no longer connect to my Windows 7 pc. Plugging in the iPod via USB does not trigger any sort of dialog box in Windows and it doesn't trigger a message saying a device has been connected; the iPod does not show up in either iTunes, Computer, Device Manager or Devices and Printers, either as an Apple mobile device or an unrecognized device, and does not charge when connected to USB (though the wall-charger still works). As far as my computer is concerned this iPod does not exist. I had successfully synced this iPod as recently as one week ago and am ready to pitch the thing in the garbage if I can't find a solution.
I have the latest version of iTunes as well as the most up-to-date Windows updates. I have already followed all the steps listed here (iOS: Device not recognized in iTunes for Windows) multiple times with no success.
I also have tried following the instructions listed here (Re: For those Windows users who suddenly cannot see their device in iTunes. Here's a solution that has worked.) but this also hasn't worked since the iPod isn't recognized in the Device Manager and I am not given the option of updating the drivers, manually or otherwise.
I have uninstalled/re-installed iTunes and all related Apple services multiple times. The Apple Mobile Device Service is functioning normally. iTunes diagnostics indicate that there is no device connected no matter what I do. I have reinstalled my Windows USB drivers and changed the settings on the USB Root Hub in the Windows Device Manager to disable power saving options.
I have tried connecting the device to another PC which detects and syncs another apple device (iPhone 5) with no issues, and had the exact same result: the computer doesn't even recognize an iPod is connected.
I can't update the Apple Mobile Device Drivers because the device is not recognized by my machine in any way.
I even completely reset my iPod and that just left me with a unactivated iPod that still isn't detected.
I am really unbelievably fed-up with the useless "try checking your USB cable"-style advice that people seem to offer on this forum. If anybody has dealt with this issue and has any serious advice other than "re-install iTunes," it would be much appreciated.

You said "I am really unbelievably fed-up with the useless "try checking your USB cable"-style"
- Did you try another cable?
- Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
Try on another computer

Issue with PTO (Paid Time Off) quota generation

Hi All,
We have an issue with quota generation of PTO for our employees.
The issue goes like this:
We have a Paid time off for employees 5weeks( 200 hrs) for employees who have worked less than 5 years.
we have paid time off for employees 6 weeks ( 240 hrs) for employees who have worked more than 5 years.
we have the following logic that has to go in this config:
-- Our fiscal year starts on Feb 1st and ends on Jan end or Feb starts which has a full week of working days. ( ex: if 01/31/2012 falls on a Thursday the following Monday which has full 5 day working week would be the end of the fiscal year).
-- Depending on the working hours of the employees and the date of joining for the first year ( for new hires)0041 info type the eligibility gets varied and reduced. Ex( employees who joins on start of fiscal year and works 40hrs per week schedules is eligible for 200hrs of PTO. Employees who join in the month of august and works for 35 hrs per week ( i.e mid of fiscal year) would get 91 hrs of PTO.
I need to put this in the system. I am thinking this could be done with out tweaking PCR.I need help in configuring this in Absence quotas as to what are the things i need change in system config and how do i do it. Please help with some screen shots if possible. I really need this to get it done ASAP. Looking forward for help.
Thanks,
Chowdary.

We use TM00 schema. Can i call TS15 and TS 12 rules into TM00 acheieve my issue of quota entilements?
Iam doing this because my businees needs to see if an employee chages his work schedule from 40 to 30 or 20 etc.. the PTO has to vary accordingly.
As the minimum eligibility is to work for 20 hrs to avail the PTO days. If at any point the employee drops it under 20 he will not be eligible till he work any this >= 20hrs per month so the evaluation has to check periodically to update the quota availability.... I need help plz suggest ...

I'm trying to get the ios 4.2.1 on my second generation iPod . Is there a way to install it directly on my iPod touch because my iTunes on my computer is not working. Please help Apple! I need the update. Just give me a link.

Im trying to get the ios 4.1.2 on my iPod touch 2nd generation. Can I install it directly on my iPod . My iTunes on my computer isn't working!

you have to have itunes installed but check out http://support.apple.com/kb/ht4623.

Report generation toolkit and signal express user step : problem of closing reference in "Stop" event

Hi all,
I'm trying to make a package of Vis to easily make Excel reports with Signal Express. I'm working on LabVIEW 8.2.1.
I'm using the report generation toolkit, so I build a .llb from my project which contains all the hierarchy of my steps, but also the hierarchy of dynamic VIs called.
I have made some steps, like "Open Workbook", "Write Data", etc.
My steps run well, excepts one step : "Close Workbook".
If my "Close Workbook" step is firing on "Run" Signal Express event, I have no error, so my reference is properly closed.
But if my "Close Workbook" step is firing on "Stop" Signal Express event, I have an error "1", from "Generate Report Objectrepository.vi".
I feel that I'm trying to use a reference which has been killed in the "Stop" step...
I would like to know what exactly do Signal Express on "Stop" event and why my close function does'nt run well.
Thanks,
Callahan

Hi Callahan,
SignalExpress (SE for short) does the following on the Stop event:
1. Takes the list of parameters that SE found on your VI's connector pane, and sets the values that the user set from the "Run LabVIEW VI" configuration page, if any.
2. Then tells the VI that SE is running the Stop event by setting the Enum found on your VI's front panel. This in turn should produce some boolean values telling your VI to execute the Stop case.
3. The VI is then run, with those values and states.
4. SE checks to see if any errors where returned.
5. Since this is the Stop event, SE releases the reference to the VI which it possesses.
Questions for you would be, is the reference to your Workbook linked to a control on your connector pane, or held in a uninitialized Shift Register. If it's held in a Shift Register, SE would not be aware of it, and would not be able to affect that reference.
Hope that helps. Feel free to post your LLB if it doesn't.
Phil

SSCC Generation

Similar Messages

Maybe you are looking for