Stupid network question - adding second nic for inside network

Solaris 10 06/06
Server: V210
Has 4 nic's
Currently have the system setup with 1 nic setup and running to normal outside IP on a business network. Works find, no issues.
I want to use a second nic to allow connection to an internal 192.168.... network so that I can access it from a workstation inside.
IP would be 192.168.1.17 gateway 192.168.1.1
So...
ifconfig bge1 plumb up
ifconfig 192.168.1.17 netmask 255.255.255.0
ifconfig -a shows...
bge1: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 4
        inet 192.168.1.17 netmask ffffff00 broadcast 192.168.1.255
        ether 0:3:ba:5a:5c:52 netstat -rn shows....
Routing Table: IPv4
Destination           Gateway           Flags Ref   Use   Interface
XXX.XXX.176.160      XXX.XXX.176.162      U         1    806 bge0
192.168.1.0          192.168.1.17         U         1      2 bge1
224.0.0.0            XXX.XXX.176.162      U         1      0 bge0
default              XXX.XXX.176.161      UG        1 334165
127.0.0.1            127.0.0.1            UH        5    142 lo0Note: the xxx.xxx... interface is the working main interface to the outside world.
I can ping the 192.168.1.17 which is the nic in the server, but can't ping say the gateway 192.168.1.1
Seems like I need a default route for it, but I already have a default for the normal network.
Clue as to what I am overlooking.
Note: this is in the global zone. I plan on letting a zone access this as well.

Odd, i would expect the ifconfig -a output from the bge1 interface to contain "RUNNING", such as.
bge0: flags=1100843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
Are you certain the card got link? And that the router is pingable?
.7/M.

Similar Messages

Although I'm connected to my WIFI network my computer keeps "looking for new networks" How can I stop it from doing so when I'm working at home and don't want another network?

Although I'm connected to my Wi-Fi network my computer keeps "looking for new networks." How can I stop it from doing so when I'm working at home and don't want another network?

You might want to update Safari to 3.12. I would empty the safari cache. (Safari>Empty Cache). Then quit Safari. System Preferences>Network>Show:Airport>TCP/IP. Insert the following into the DNS Servers box;
208.67.222.222
208.67.220.220
then hit apply. Now launch Safari. You should also try powering down modem, router and Mac and power up in 2 minute sequence; modem, router, Mac.

My wifi will not detect networks and will not search for other networks when I search for them. Do I need a new iPhone or can I fix it myself?

My wifi is on and when it tries to find a wifi connection, the gray little circle just keeps spinning and will not detect our home wifi. I have tried to search for it and connect to it manually, but it will not search for the network name. I'm hoping I don't need a new phone so please help.

The following may have something that will help: http://support.apple.com/kb/TS1398

Added second laptop to home network and first laptop connection GONE

Help! I have a WRT54G2 v1.5 wireless-G broadban router set up on my hard-wired computer (XP) and had my new Sony Vaio laptop (Windows 7) connected wirelessly. Everything worked great! Then, yesterday, I added a Dell laptop to the network and my Sony got kicked off the network. I have tried to "add a device" but when I click on the link to do that from Network Magic, I get an error page on the Internet. I saw that someone else had a connection problem so I read the answer posted to their question and clicked on the link and again, get an Internet error. I am connected to the Internet: I checked! What is going on? I need the Dell laptop on the network as it is my new laptop for my job. Help!

Let mw know the model number of router …also tell me the Operating system on laptop.

Network question. Use coax for ethernet?

I heard there's a way to use an existing coaxial cable for an ethernet connection? I have my iMac in our converted garage out back of the main house, and the airport/. internet connection inside the main house. I have them communicate wirelessly now and it's fine, but drops out now and then and I wanted to hook it up by wire.
There's a coax cable laid between the two houses, but no room/facility for adding an ethernet cable, easily anyway. I was told you can get adapaters to use the coax for this purpose. I looked around online and there's a variety of things available, from simple adapaters for $10 or $20, to complex boxes that cost a hundred to several hundred. Anybody know if this is possible, and if it is, what kind of adapter I need?

Meetoo wrote:
I heard there's a way to use an existing coaxial cable for an ethernet connection? I have my iMac in our converted garage out back of the main house, and the airport/. internet connection inside the main house. I have them communicate wirelessly now and it's fine, but drops out now and then and I wanted to hook it up by wire.
There's a coax cable laid between the two houses, but no room/facility for adding an ethernet cable, easily anyway. I was told you can get adapaters to use the coax for this purpose. I looked around online and there's a variety of things available, from simple adapaters for $10 or $20, to complex boxes that cost a hundred to several hundred. Anybody know if this is possible, and if it is, what kind of adapter I need?
Coax ("10base2') was the second-generation Ethernet connection technique. (The first was "thicknet"; the third "twisted pair" - "10baseT"). Do a Google search for "10base2".

Using Server X as a screen for inside network?

I searched for information on this and wasn't able to turn up anything useful, but it's possible I missed it, so pardon me if I'm bringing something up that's already discussed at length and just point me in the right direction.
I'm managing a small network that operates a radio station's automation software. It is the desire of the managers to keep this system isolated to keep it from coming under attack and to keep the music from getting stolen. (the automation computers and servers are PC WXP) However, I need to have some access to certain things on the outside, and I'm having trouble figuring out how to make that work. At this point, I have two requirements:
1. FTP Server that is accessable from the outside, and from the inside without exposing the inside to the outside.
2. Access to an online database (for song info,titles, etc, basically like CDDB), again without exposing the inside computers to the outside.
My idea is to set up a mac with OSX Server on it with two NIC and have it run the ftp server. Then to use it as a "screen" for accessing the music database, like a proxy server or something.
I hope what I'm getting at is clear here.
Any ideas, suggestions? Any help would be greatly appreciated. Thank you.
Radio Josh

VPN on the really simple side is a key system to a locked door. That door being the firewall. What is on the other side? Your whole network as if you where plugged in right next to your PC's except for LAN speed you get WAN speed, lol.
Now on the surface that may sound dangerous but VPN's provide a very secure way to get access to your network of PC's behind the firewall. On some firewalls they can be a bit tricky to setup but nowadays firewalls have it so a kid can set it up.
On the firewall you set the Virtually Private Network (VPN) up and you will in the process generate a "key". You then use this key w/software or OS add-on that will allow you from your home PC to get to the firewall and see the other side. Then you can connect to any local PC in the office that is setup to let you.
Hope that clears it up for you.
BTW, If at some later date you where planning on doing web-hosting for the office, e-mail hosting, database shares, Calendar collaboration, or any other type of server related thinks I would say get OS X Server cause it can do just about everything.

Adding second airport express to network problem

Hi all. I currently have and airport extreme and airport express in range extending mode which have been working flawlessly for 3 years. I am trying to add an additional, newer airport express to put in another location. After setting the new one up in airport utility the light on the new express is green but in airport utilities in shows yellow. Troubleshooting said I needed to update firmware, which I have done. Still have the same issue. Now when I click continue in the airport utility it tells me the unit is setup and working, yet it still shows yellow in airport utility window. Quite confused. Any ideas?

Never mind. I figured it out.

Time Capsule - Can it run as DHCP router, create a wireless network and plug into switch for wired network all at the same time?

I have a closet with Wired connections from all over the house terminating in it. I also have the internet modem and a switch in this closet. My old setup was a netgear in the closet creating a wireless network and also feeding the Ethernet ports all over the house. In my room, I had an Airport express (a month old) bridging the wifi to make the wifi network larger. The Express was hard wired from the wall and my mac mini was using it's wifi (printer was plugged into other ethernet port). Everything was working great.
Fast forward to last week. My Netgear died. So, I bought a time capsule. My plan was to move the Express to the closet and have it create the wifi network and also then run cat 5 cord from express to the switch to feed all the wired wall plugs. Reset it and set it up to create the wifi network as well as DCHP NAT. Wireless was running great on it. Then I plugged in the Cat 5 in the second Ethernet Port to the switch. Wifi stopped working and none of the computers would connect using wired connections either. They would see a 'network' but nothing would work. I would unplug the Cat 5 feeding the swtich and the wireless would start working again. Plug the Cat 5 back in and wireless would stop.
So I thought I would try the Time Capsule in the closet and see if I could get it to work. Pretty much the same thing, except at this point I figured out if I went in and told it NOT to create a wifi network the wired portion worked fine and all the wired computers in the house worked fine. Of course, then I didn't have Wifi.
I'm not clueless when it comes to networking, but I can NOT figure this out! Can either the Time Capsule or Express Create the wifi network AND also feed the data to the switch for all the wired computers?
To simplify this is what I want my end result to be. I prefer the Time Capsule to be the wireless connection extender, but if I have to have the Express do it, I'm fine with that.
1. Express in the closet creating the wifi network as well as feeding the data to the wired connections via my switch.
2. have the Time capsule in my room at the opposite end of the house plugged into the hard wired connection to extend the wrieless network as well as have wired connections such as my printer and my Mac Mini.
If I can get #1 to work, I don't think I'll have any problems with #2. Help!

I have an equally complex setup with a managed switch actually but I have never seen the TC have this kind of issue.
What I do notice is you have changed the TC from defaults.. you are using a non-default IP range.
I have run across issues like this where people move things from default.
I would like you to start over.. factory reset the TC. That will set it back to default router mode.
Do the min setup on the TC..
1. Change all names from what you were using. That includes the TC name and wireless name/s
Make them short, no spaces and pure alphanumeric because that is the correct way to network. Apple default names with spaces and apostrophes are fundamentally bad.
2. With just the TC plugged into the switch.. and a single computer connected by ethernet. Power cycle the whole network.. this allows the switch to clear all the old MAC address.
3. Test on the computer just ethernet. Turn the wireless off.
The computer must use dhcp and must get an ip from the TC.
It has to get the correct Router.. ie Gateway.. I wish apple could stick with proper network terminology.
And it must get same address or valid DNS server address/es.
If it fails.. please plug ethernet directly to the TC.. bypassing the switch.
You should get the standard IP addressing and internet connection.
If not please post the screenshot from the Mac of the network preferences showing the ethernet setup.
I need to see what address it does get. I need you to make sure the ethernet is the TOP of the list. So rearrange the order of network connection. With the airport off it should just go to the top of the list.
If it appears to be working .. but a browser cannot connect, open a terminal and ping an internet address.
Ping the actual gateway address the ISP gives you and ping the ISP dns address.

Best Practice setting up NICs for Hyper V 2008 r2

I am looking at some suggestions for best practice for setting up a hyper V 2008 r2 at a remote location with 5 nics, one for managment vlan and other 4 on the data vlan. This server will host 2 virtual machines, one is a DC and the other
is a member local DHCP server. The server is setup now with one nic on the management Vlan and the other nic's set to get there ip from the local dhcp server on on the host. We have the virtual networks setup in Hyper V to
point to each of the nics using the "external connection". The virtual servers 'DHCP and AD" have there own ip set within them. Issues we are seeing, when the site looses external connections for a while they cannot get ip
addresses from the local dhcp server anymore.
1. NIC on management Vlan -- IP Static -- Physical host
2. NIC on the Data network Vlan -- DHCP linked as a connection "external" in Hyper V -- virtual server DHCP
3. NIC on the Data network Vlan -- DHCP linked as a connection "external" in Hyper V -- Virtual server domain controller
4. NIC on the Data network Vlan -- DHCP linked as a connection "external" in Hyper V -- extra
5. NIC on the Data network Vlan -- DHCP linked as a connection "external" in Hyper V -- extra
Thanks in advance

Looks like you may be over complicating things here. More and more of the recommendations from Microsoft at this point would be to create a Logical Switch and then layer on Logical Networks for your management layers, but here is what I would do for
you simple remote office.
Management NIC: Looks good (Teaming would be better, but only if you had 2 different switching to protect against link failures at the switch level. Doesn't seem relevant in this case however.
NIC for Data Network VLAN: I would use one NIC in your case if you can have the ability to Trunk multiple VLANs at the switch level to the NIC. That way you are setting the VLAN on the VMs NIC that you want to access and your
Virtual Switch configuration is very simple. On this virtual switch however, I would uncheck IPv4 and IPv6. There is no need to give this NIC an address as you are just passing traffic through them from the VMs that are marked with VLAN tags. Again,
if you have multiple physical switches in the building teaming could be an option, but probably adds more complexity than is necessary for a small office.
Even if you keep your Virtual Switches linked to separate NICs unchecking IPv4 and IPv6 makes sense.
Disable all the other NICs
Beyond that, check your routing. Can you ping between all hosts when there is not interruption? What DHCP server are they getting there addresses on normally? Where are your name resolution servers (DNS, WINS)?
No silver bullet here, but maybe a step in the right direction.
Rob McShinsky (VirtuallyAware.com)
VirtuallyAware - Experiences in a Virtual World (Microsoft MVP - Virtual Machine)

Oracle VM Server for SPARC - network multipathing architecture question

This is a general architecture question about how to best setup network multipathing
I am reading the "Oracle VM Server for SPARC 2.2 Administration Guide" but I can't find what I am looking for.
From reading the document is appears it is possible to:
(a) Configure IPMP in the Service Domain (pg. 155)
- This protects against link level failure but won't protect against the failure of an entire Service LDOM?
(b) Configure IPMP in the Guest Domain (pg. 154)
- This will protect against Service LDOM failure but moves the complexity to the Guest Domain
- This means the there are two (2) VNICs in the guest though?
In AIX, "Shared Ethernet Adapter (SEA) Failover" it presents a single NIC to the guest but can tolerate failure of a single VIOS (~Service LDOM) as well as link level failure in each VIO Server.
https://www.ibm.com/developerworks/mydeveloperworks/blogs/aixpert/entry/shared_ethernet_adapter_sea_failover_with_load_balancing198?lang=en
Is there not a way to do something similar in Oracle VM Server for SPARC that provides the following:
(1) Two (2) Service Domains
(2) Network Redundancy within the Service Domain
(3) Service Domain Redundancy
(4) Simplify the Guest Domain (ie single virtual NIC) with no IPMP in the Guest
Virtual Disk Multipathing appears to work as one would expect (at least according the the documentation, pg. 120). I don't need to setup mpxio in the guest. So I'm not sure why I would need to setup IPMP in the guest.
Edited by: 905243 on Aug 23, 2012 1:27 PM

Hi,
there's link-based and probe-based IPMP. We use link-based IPMP (in the primary domain and in the guest LDOMs).
For the guest LDOMs you have to set the phys-state linkprop on the vnets if you want to use link-based IPMP:
ldm set-vnet linkprop=phys-state vnetX ldom-name
If you want to use IPMP with vsw interfaces in the primary domain, you have to set the phys-state linkprop in the vswitch:
ldm set-vswitch linkprop=phys-state net-dev=<phys_iface_e.g._igb0> <vswitch-name>
Bye,
Alexander.

Problem with nat / access rule for webserver in inside network asa 5505 7.2

Hello,
i have trouble setting up nat and access rule for webserver located in inside network.
I have asa 5505 version 7.2 and it has to active interfaces, inside 192.168.123.0 and outside x.x.x.213
Webserver has ip 192.168.123.11 and it needs to be accessed from outside, ip x.x.x.213.
I have created an static nat rule with pat (as an appendix) and access rules from outside network to inside interface ip 192.168.123.11 (tcp 80) but no luck.
What am i doing wrong?

Command:
packet-tracer input outside tcp 188.x.x.213 www 192.168.123.11 www detailed
Phase: 1
Type: FLOW-LOOKUP
Subtype:
Result: ALLOW
Config:
Additional Information:
Found no matching flow, creating a new flow
Phase: 2
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in   192.168.123.0   255.255.255.0   inside
Phase: 3
Type: ACCESS-LIST
Subtype:
Result: DROP
Config:
Implicit Rule
Additional Information:
Forward Flow based lookup yields rule:
in id=0x35418d8, priority=500, domain=permit, deny=true
    hits=1, user_data=0x6, cs_id=0x0, reverse, flags=0x0, protocol=0
    src ip=188.x.x.213, mask=255.255.255.255, port=0
    dst ip=0.0.0.0, mask=0.0.0.0, port=0
Result:
input-interface: outside
input-status: up
input-line-status: up
output-interface: inside
output-status: up
output-line-status: up
Action: drop
Drop-reason: (acl-drop) Flow is denied by configured rule

How to configure oracle dataguard for connecting to the second nic.

hi
i want deploy my oracle dataguard on a remote site on a separate lease line
and on the second nic of the primary. i just have a concern that what
configurations should be made in the primary or standby to make sure the replication can work as the first nic is connected to receive the general database
data and the second nic is being planned for replication only.
so how standby will come to know that it has to pick which one of then.
waiting for an early reply
manish lall
[email protected]

thanks for the reply
does that mean nothing is to be needed to configure for oracle standby as such.
can you give me some idea of how this ip routing configuration will be done

As soon as I keep the iPhone (iPhone 5) on the desk the network goes off and when I swipe it then only it starts searching for the network and get it in 30 seconds. If someone is calling me during that time it says mobile is either switched off or outsid

As soon as I keep the iPhone (iPhone 5) on the desk the network goes off and when I swipe it then only it starts searching for the network and get it in 30 seconds.
If someone is calling me during that time it says mobile is either switched off or outside the coverage area.
Please help

You may need to force it into recovery mode. See here: https://discussions.apple.com/message/17766427#17766427

I've just bought an ipod touch. I cannot get beyond the question asking me for a network name. I don't have a mobile telephone which I think this question is referring to. All I want from an ipod is to listen to music. What should I do?

I've just bought an ipod touch but I cannot get beyond the question asking me for a network name. I don't have a mobile telephone which I think this question is referring to. All I want from an ipod is to listen to music. What should I do?

You have to activate a new iPod by either setting it up via wifi network that has an internet connection on to connect to a computer that has iTunes and an internet connection.
You can go to an Apple store or or to a friend's house if necessary

Need help adding second laptop to network

Please help. I am so frustrated. I setup our new gateway wirelessly using the WRT160N router. Had to call the help line and they helped me go online and configure the router settings. Now I am trying to add a second older laptop (HP Pavilion ZE4400). When I use the disc to install the router info, it stops after it says waiting for the router. Then I get an error message telling me to restore the router to it's default settings. I don't want to undo all that I did with support on the phone. It took forever. Why can I not install the router software on the HP? Can someone help me fix this problem?
Thanks in advance

If your router is already configured then,do not run the CD on the computer to connect the Wireless Network...Make sure that wi-fi switch is turn ON.
For XP...Click on Start and goto the Control Panel and double click on Network Connections, Right click on the Wireless Network Connection and click on View Available Wireless Networks and select your Wireless Network and click Connect...Now it will give you the opportunity to put the network/wep key, make sure you enter the correct network key and confirm it...It will connect.
For Vista...Click Start >> Control Panel >> Network and Sharing Center >>Click on Connect to a Network and select your Wireless Network and click Connect, it should ask for your Network Key/Password, enter the correct password/network key and click Connect...It should connect...Once you are connected you should restart the computer, it should connect to Internet...

Stupid network question - adding second nic for inside network

Similar Messages

Maybe you are looking for