System/fmd:default failed: transitioned to maintenance. Can't clear
Hi all.
After our latest patching window on our Sun Solaris 10 x86 systems (SunFire x4200M2's), we have found the following error occuring across all our hosts:
SunOS somehost 5.10 Generic_127112-10 i86pc i386 i86pc
+Mar 1 15:26:17 somehost svc.startd[7]: [ID 748625 daemon.error] system/fmd:default failed: transitioned to maintenance (see 'svcs -xv' for details)+
We are trying to isolate the cause of why the fmd would not start. So far, we've tried to:
[root@somehost:/] $ svcadm clear svc:/system/fmd:default
...and we've looked at the output:
svc:/system/fmd:default (Solaris Fault Manager)
State: maintenance since Sat Mar 01 18:05:29 2008
Reason: Start method failed repeatedly, last exited with status 1.
See: http://sun.com/msg/SMF-8000-KS
See: man -M /usr/share/man -s 1M fmd
See: /var/svc/log/system-fmd:default.log
Impact: This service is not running.
So at this point, we thought to check if any dependencies were problematic:
[root@somehost:/] $ svcs -d fmd
STATE STIME FMRI
online 15:25:46 svc:/system/filesystem/minimal:default
online 15:25:47 svc:/system/sysevent:default
online 15:26:07 svc:/network/rpc/bind:default
online 15:26:10 svc:/system/dumpadm:default
...unfortunately, it seems fine! At this point - we thought we'd try to reload the smf manifest for fmd:
1. svcadm disable system/fmd
2. svccfg
3. delete system/fmd
4. import /var/svc/manifest/system/fmd.xml
5. quit
...and it STILL doesn't appear to have helped. The service is always:
maintenance 18:06:34 svc:/system/fmd:default
...any help would be greatly appreciated!
Thanks.
z
OK. Here is some truss output. Hope it isn't too complex/messy for the thread:
execve("/usr/lib/fm/fmd/fmd", 0x08047C58, 0x08047C60) argc = 1
resolvepath("/usr/lib/ld.so.1", "/lib/ld.so.1", 1023) = 12
resolvepath("/usr/lib/fm/fmd/fmd", "/usr/lib/fm/fmd/fmd", 1023) = 19
sysconfig(_CONFIG_PAGESIZE) = 4096
xstat(2, "/usr/lib/fm/fmd/fmd", 0x08047A38) = 0
open("/var/ld/ld.config", O_RDONLY) Err#2 ENOENT
mmap(0x00000000, 4096, PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE|MAP_ANON, -1, 0) = 0xFEFC0000
xstat(2, "/usr/openwin/lib/libtopo.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/lib/fm/libtopo.so.1", 0x08047268) = 0
resolvepath("/usr/lib/fm/libtopo.so.1", "/usr/lib/fm/libtopo.so.1", 1023) = 24
open("/usr/lib/fm/libtopo.so.1", O_RDONLY) = 3
mmap(0x00010000, 32768, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_ALIGN, 3, 0) = 0xFEFB0000
mmap(0x00010000, 172032, PROT_NONE, MAP_PRIVATE|MAP_NORESERVE|MAP_ANON|MAP_ALIGN, -1, 0) = 0xFEF80000
mmap(0xFEF80000, 97805, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_TEXT, 3, 0) = 0xFEF80000
mmap(0xFEFA8000, 4642, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_INITDATA, 3, 98304) = 0xFEFA8000
munmap(0xFEF98000, 65536) = 0
memcntl(0xFEF80000, 14992, MC_ADVISE, MADV_WILLNEED, 0, 0) = 0
close(3) = 0
xstat(2, "/usr/openwin/lib/libdiagcode.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/lib/fm/libdiagcode.so.1", 0x08047268) = 0
resolvepath("/usr/lib/fm/libdiagcode.so.1", "/usr/lib/fm/libdiagcode.so.1", 1023) = 28
open("/usr/lib/fm/libdiagcode.so.1", O_RDONLY) = 3
mmap(0xFEFB0000, 32768, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0xFEFB0000
mmap(0x00010000, 81920, PROT_NONE, MAP_PRIVATE|MAP_NORESERVE|MAP_ANON|MAP_ALIGN, -1, 0) = 0xFEF60000
mmap(0xFEF60000, 11401, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_TEXT, 3, 0) = 0xFEF60000
mmap(0xFEF73000, 1433, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_INITDATA, 3, 12288) = 0xFEF73000
munmap(0xFEF63000, 65536) = 0
memcntl(0xFEF60000, 1912, MC_ADVISE, MADV_WILLNEED, 0, 0) = 0
close(3) = 0
xstat(2, "/usr/openwin/lib/libsysevent.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/lib/fm/libsysevent.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/lib/libsysevent.so.1", 0x08047268) = 0
resolvepath("/lib/libsysevent.so.1", "/lib/libsysevent.so.1", 1023) = 21
open("/lib/libsysevent.so.1", O_RDONLY) = 3
mmap(0xFEFB0000, 32768, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0xFEFB0000
mmap(0x00010000, 98304, PROT_NONE, MAP_PRIVATE|MAP_NORESERVE|MAP_ANON|MAP_ALIGN, -1, 0) = 0xFEF40000
mmap(0xFEF40000, 24682, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_TEXT, 3, 0) = 0xFEF40000
mmap(0xFEF57000, 849, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_INITDATA, 3, 28672) = 0xFEF57000
munmap(0xFEF47000, 65536) = 0
memcntl(0xFEF40000, 6344, MC_ADVISE, MADV_WILLNEED, 0, 0) = 0
close(3) = 0
xstat(2, "/usr/openwin/lib/libsmbios.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/lib/fm/libsmbios.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/lib/libsmbios.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/lib/libsmbios.so.1", 0x08047268) = 0
resolvepath("/usr/lib/libsmbios.so.1", "/usr/lib/libsmbios.so.1", 1023) = 23
open("/usr/lib/libsmbios.so.1", O_RDONLY) = 3
mmap(0xFEFB0000, 32768, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0xFEFB0000
mmap(0x00010000, 114688, PROT_NONE, MAP_PRIVATE|MAP_NORESERVE|MAP_ANON|MAP_ALIGN, -1, 0) = 0xFEF20000
mmap(0xFEF20000, 41737, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_TEXT, 3, 0) = 0xFEF20000
mmap(0xFEF3B000, 452, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_INITDATA, 3, 45056) = 0xFEF3B000
munmap(0xFEF2B000, 65536) = 0
mmap(0x00000000, 4096, PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE|MAP_ANON, -1, 0) = 0xFEF10000
memcntl(0xFEF20000, 5924, MC_ADVISE, MADV_WILLNEED, 0, 0) = 0
close(3) = 0
xstat(2, "/usr/openwin/lib/libuuid.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/lib/fm/libuuid.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/lib/libuuid.so.1", 0x08047268) = 0
resolvepath("/lib/libuuid.so.1", "/lib/libuuid.so.1", 1023) = 17
open("/lib/libuuid.so.1", O_RDONLY) = 3
mmap(0xFEFB0000, 32768, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0xFEFB0000
mmap(0x00010000, 86016, PROT_NONE, MAP_PRIVATE|MAP_NORESERVE|MAP_ANON|MAP_ALIGN, -1, 0) = 0xFEEF0000
mmap(0xFEEF0000, 13558, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_TEXT, 3, 0) = 0xFEEF0000
mmap(0xFEF04000, 656, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_INITDATA, 3, 16384) = 0xFEF04000
munmap(0xFEEF4000, 65536) = 0
memcntl(0xFEEF0000, 3236, MC_ADVISE, MADV_WILLNEED, 0, 0) = 0
close(3) = 0
xstat(2, "/usr/openwin/lib/libdoor.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/lib/fm/libdoor.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/lib/libdoor.so.1", 0x08047268) = 0
resolvepath("/lib/libdoor.so.1", "/lib/libdoor.so.1", 1023) = 17
open("/lib/libdoor.so.1", O_RDONLY) = 3
mmap(0xFEFB0000, 32768, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0xFEFB0000
mmap(0x00010000, 73728, PROT_NONE, MAP_PRIVATE|MAP_NORESERVE|MAP_ANON|MAP_ALIGN, -1, 0) = 0xFEED0000
mmap(0xFEED0000, 3595, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_TEXT, 3, 0) = 0xFEED0000
mmap(0xFEEE1000, 328, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_INITDATA, 3, 4096) = 0xFEEE1000
munmap(0xFEED1000, 65536) = 0
memcntl(0xFEED0000, 2048, MC_ADVISE, MADV_WILLNEED, 0, 0) = 0
close(3) = 0
xstat(2, "/usr/openwin/lib/libnvpair.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/lib/fm/libnvpair.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/lib/libnvpair.so.1", 0x08047268) = 0
resolvepath("/lib/libnvpair.so.1", "/lib/libnvpair.so.1", 1023) = 19
open("/lib/libnvpair.so.1", O_RDONLY) = 3
mmap(0xFEFB0000, 32768, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0xFEFB0000
mmap(0x00010000, 94208, PROT_NONE, MAP_PRIVATE|MAP_NORESERVE|MAP_ANON|MAP_ALIGN, -1, 0) = 0xFEEB0000
mmap(0xFEEB0000, 22818, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_TEXT, 3, 0) = 0xFEEB0000
mmap(0xFEEC6000, 588, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_INITDATA, 3, 24576) = 0xFEEC6000
munmap(0xFEEB6000, 65536) = 0
memcntl(0xFEEB0000, 6848, MC_ADVISE, MADV_WILLNEED, 0, 0) = 0
close(3) = 0
xstat(2, "/usr/openwin/lib/libexacct.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/lib/fm/libexacct.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/lib/libexacct.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/lib/libexacct.so.1", 0x08047268) = 0
resolvepath("/usr/lib/libexacct.so.1", "/usr/lib/libexacct.so.1", 1023) = 23
open("/usr/lib/libexacct.so.1", O_RDONLY) = 3
mmap(0xFEFB0000, 32768, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0xFEFB0000
mmap(0x00010000, 86016, PROT_NONE, MAP_PRIVATE|MAP_NORESERVE|MAP_ANON|MAP_ALIGN, -1, 0) = 0xFEE90000
mmap(0xFEE90000, 15007, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_TEXT, 3, 0) = 0xFEE90000
mmap(0xFEEA4000, 408, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_INITDATA, 3, 16384) = 0xFEEA4000
munmap(0xFEE94000, 65536) = 0
mmap(0x00000000, 4096, PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE|MAP_ANON, -1, 0) = 0xFEE80000
memcntl(0xFEE90000, 3232, MC_ADVISE, MADV_WILLNEED, 0, 0) = 0
close(3) = 0
xstat(2, "/usr/openwin/lib/libnsl.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/lib/fm/libnsl.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/lib/libnsl.so.1", 0x08047268) = 0
resolvepath("/lib/libnsl.so.1", "/lib/libnsl.so.1", 1023) = 16
open("/lib/libnsl.so.1", O_RDONLY) = 3
mmap(0xFEFB0000, 32768, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0xFEFB0000
mmap(0x00010000, 647168, PROT_NONE, MAP_PRIVATE|MAP_NORESERVE|MAP_ANON|MAP_ALIGN, -1, 0) = 0xFEDE0000
mmap(0xFEDE0000, 524633, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_TEXT, 3, 0) = 0xFEDE0000
mmap(0xFEE71000, 19869, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_INITDATA, 3, 528384) = 0xFEE71000
mmap(0xFEE76000, 30032, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_ANON, -1, 0) = 0xFEE76000
munmap(0xFEE61000, 65536) = 0
memcntl(0xFEDE0000, 57668, MC_ADVISE, MADV_WILLNEED, 0, 0) = 0
close(3) = 0
xstat(2, "/usr/openwin/lib/librt.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/lib/fm/librt.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/lib/librt.so.1", 0x08047268) = 0
resolvepath("/lib/librt.so.1", "/lib/librt.so.1", 1023) = 15
open("/lib/librt.so.1", O_RDONLY) = 3
mmap(0xFEFB0000, 32768, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0xFEFB0000
mmap(0x00010000, 94208, PROT_NONE, MAP_PRIVATE|MAP_NORESERVE|MAP_ANON|MAP_ALIGN, -1, 0) = 0xFEDC0000
mmap(0xFEDC0000, 22982, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_TEXT, 3, 0) = 0xFEDC0000
mmap(0xFEDD6000, 750, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_INITDATA, 3, 24576) = 0xFEDD6000
munmap(0xFEDC6000, 65536) = 0
memcntl(0xFEDC0000, 8548, MC_ADVISE, MADV_WILLNEED, 0, 0) = 0
close(3) = 0
xstat(2, "/usr/openwin/lib/libumem.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/lib/fm/libumem.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/lib/libumem.so.1", 0x08047268) = 0
resolvepath("/lib/libumem.so.1", "/lib/libumem.so.1", 1023) = 17
open("/lib/libumem.so.1", O_RDONLY) = 3
mmap(0xFEFB0000, 32768, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0xFEFB0000
mmap(0x00010000, 196608, PROT_NONE, MAP_PRIVATE|MAP_NORESERVE|MAP_ANON|MAP_ALIGN, -1, 0) = 0xFED80000
mmap(0xFED80000, 85709, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_TEXT, 3, 0) = 0xFED80000
mmap(0xFEDA5000, 19020, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_INITDATA, 3, 86016) = 0xFEDA5000
mmap(0xFEDAA000, 22088, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_ANON, -1, 0) = 0xFEDAA000
munmap(0xFED95000, 65536) = 0
memcntl(0xFED80000, 22832, MC_ADVISE, MADV_WILLNEED, 0, 0) = 0
close(3) = 0
xstat(2, "/usr/openwin/lib/libdevinfo.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/lib/fm/libdevinfo.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/lib/libdevinfo.so.1", 0x08047268) = 0
resolvepath("/lib/libdevinfo.so.1", "/lib/libdevinfo.so.1", 1023) = 20
open("/lib/libdevinfo.so.1", O_RDONLY) = 3
mmap(0xFEFB0000, 32768, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0xFEFB0000
mmap(0x00010000, 155648, PROT_NONE, MAP_PRIVATE|MAP_NORESERVE|MAP_ANON|MAP_ALIGN, -1, 0) = 0xFED50000
mmap(0xFED50000, 82102, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_TEXT, 3, 0) = 0xFED50000
mmap(0xFED75000, 1823, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_INITDATA, 3, 86016) = 0xFED75000
munmap(0xFED65000, 65536) = 0
mmap(0x00000000, 4096, PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE|MAP_ANON, -1, 0) = 0xFED40000
memcntl(0xFED50000, 12572, MC_ADVISE, MADV_WILLNEED, 0, 0) = 0
close(3) = 0
xstat(2, "/usr/openwin/lib/libc.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/lib/fm/libc.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/lib/libc.so.1", 0x08047268) = 0
resolvepath("/lib/libc.so.1", "/lib/libc.so.1", 1023) = 14
open("/lib/libc.so.1", O_RDONLY) = 3
mmap(0xFEFB0000, 32768, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0xFEFB0000
mmap(0x00010000, 876544, PROT_NONE, MAP_PRIVATE|MAP_NORESERVE|MAP_ANON|MAP_ALIGN, -1, 0) = 0xFEC60000
mmap(0xFEC60000, 772077, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_TEXT, 3, 0) = 0xFEC60000
mmap(0xFED2D000, 27239, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_INITDATA, 3, 774144) = 0xFED2D000
mmap(0xFED34000, 5392, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_ANON, -1, 0) = 0xFED34000
munmap(0xFED1D000, 65536) = 0
memcntl(0xFEC60000, 123384, MC_ADVISE, MADV_WILLNEED, 0, 0) = 0
close(3) = 0
xstat(2, "/usr/openwin/lib/libc.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libnvpair.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libelf.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/lib/libelf.so.1", 0x08047268) = 0
resolvepath("/lib/libelf.so.1", "/lib/libelf.so.1", 1023) = 16
open("/lib/libelf.so.1", O_RDONLY) = 3
mmap(0xFEFB0000, 32768, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0xFEFB0000
mmap(0x00010000, 176128, PROT_NONE, MAP_PRIVATE|MAP_NORESERVE|MAP_ANON|MAP_ALIGN, -1, 0) = 0xFEC30000
mmap(0xFEC30000, 103385, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_TEXT, 3, 0) = 0xFEC30000
mmap(0xFEC5A000, 2688, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_INITDATA, 3, 106496) = 0xFEC5A000
munmap(0xFEC4A000, 65536) = 0
memcntl(0xFEC30000, 9512, MC_ADVISE, MADV_WILLNEED, 0, 0) = 0
close(3) = 0
xstat(2, "/usr/openwin/lib/libumem.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libxml2.so.2", 0x08047268) Err#2 ENOENT
xstat(2, "/lib/libxml2.so.2", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/lib/libxml2.so.2", 0x08047268) = 0
resolvepath("/usr/lib/libxml2.so.2", "/usr/lib/libxml2.so.2", 1023) = 21
open("/usr/lib/libxml2.so.2", O_RDONLY) = 3
mmap(0xFEFB0000, 32768, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0xFEFB0000
mmap(0x00010000, 1196032, PROT_NONE, MAP_PRIVATE|MAP_NORESERVE|MAP_ANON|MAP_ALIGN, -1, 0) = 0xFEB00000
mmap(0xFEB00000, 1089648, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_TEXT, 3, 0) = 0xFEB00000
mmap(0xFEC1A000, 37260, PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_INITDATA, 3, 1089536) = 0xFEC1A000
munmap(0xFEC0B000, 61440) = 0
memcntl(0xFEB00000, 116324, MC_ADVISE, MADV_WILLNEED, 0, 0) = 0
close(3) = 0
xstat(2, "/usr/openwin/lib/libkstat.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/lib/libkstat.so.1", 0x08047268) = 0
resolvepath("/lib/libkstat.so.1", "/lib/libkstat.so.1", 1023) = 18
open("/lib/libkstat.so.1", O_RDONLY) = 3
mmap(0xFEFB0000, 32768, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0xFEFB0000
mmap(0x00010000, 73728, PROT_NONE, MAP_PRIVATE|MAP_NORESERVE|MAP_ANON|MAP_ALIGN, -1, 0) = 0xFEAE0000
mmap(0xFEAE0000, 3339, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_TEXT, 3, 0) = 0xFEAE0000
mmap(0xFEAF1000, 268, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_INITDATA, 3, 4096) = 0xFEAF1000
munmap(0xFEAE1000, 65536) = 0
mmap(0x00000000, 4096, PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE|MAP_ANON, -1, 0) = 0xFEAD0000
memcntl(0xFEAE0000, 1388, MC_ADVISE, MADV_WILLNEED, 0, 0) = 0
close(3) = 0
xstat(2, "/usr/openwin/lib/libuuid.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libdevinfo.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libsmbios.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/lib/libsmbios.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libc.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libc.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libnvpair.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libdoor.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libc.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libc.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libsocket.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/lib/libsocket.so.1", 0x08047268) = 0
resolvepath("/lib/libsocket.so.1", "/lib/libsocket.so.1", 1023) = 19
open("/lib/libsocket.so.1", O_RDONLY) = 3
mmap(0xFEFB0000, 32768, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0xFEFB0000
mmap(0x00010000, 114688, PROT_NONE, MAP_PRIVATE|MAP_NORESERVE|MAP_ANON|MAP_ALIGN, -1, 0) = 0xFEAB0000
mmap(0xFEAB0000, 43986, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_TEXT, 3, 0) = 0xFEAB0000
mmap(0xFEACB000, 2645, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_INITDATA, 3, 45056) = 0xFEACB000
munmap(0xFEABB000, 65536) = 0
memcntl(0xFEAB0000, 12080, MC_ADVISE, MADV_WILLNEED, 0, 0) = 0
close(3) = 0
xstat(2, "/usr/openwin/lib/libnsl.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libc.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libc.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libc.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libnsl.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libc.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libc.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libaio.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/lib/libaio.so.1", 0x08047268) = 0
resolvepath("/lib/libaio.so.1", "/lib/libaio.so.1", 1023) = 16
open("/lib/libaio.so.1", O_RDONLY) = 3
mmap(0xFEFB0000, 32768, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0xFEFB0000
mmap(0x00010000, 102400, PROT_NONE, MAP_PRIVATE|MAP_NORESERVE|MAP_ANON|MAP_ALIGN, -1, 0) = 0xFEA90000
mmap(0xFEA90000, 28365, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_TEXT, 3, 0) = 0xFEA90000
mmap(0xFEAA7000, 1378, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_INITDATA, 3, 28672) = 0xFEAA7000
mmap(0xFEAA8000, 1600, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_ANON, -1, 0) = 0xFEAA8000
munmap(0xFEA97000, 65536) = 0
memcntl(0xFEA90000, 5288, MC_ADVISE, MADV_WILLNEED, 0, 0) = 0
close(3) = 0
xstat(2, "/usr/openwin/lib/libmd.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/lib/libmd.so.1", 0x08047268) = 0
resolvepath("/lib/libmd.so.1", "/lib/libmd.so.1", 1023) = 15
open("/lib/libmd.so.1", O_RDONLY) = 3
mmap(0xFEFB0000, 32768, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0xFEFB0000
mmap(0x00010000, 126976, PROT_NONE, MAP_PRIVATE|MAP_NORESERVE|MAP_ANON|MAP_ALIGN, -1, 0) = 0xFEA60000
mmap(0xFEA60000, 56424, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_TEXT, 3, 0) = 0xFEA60000
mmap(0xFEA7E000, 552, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_INITDATA, 3, 57344) = 0xFEA7E000
munmap(0xFEA6E000, 65536) = 0
mmap(0x00000000, 4096, PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE|MAP_ANON, -1, 0) = 0xFEA50000
memcntl(0xFEA60000, 1464, MC_ADVISE, MADV_WILLNEED, 0, 0) = 0
close(3) = 0
xstat(2, "/usr/openwin/lib/libc.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libnvpair.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libsec.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/lib/libsec.so.1", 0x08047268) = 0
resolvepath("/lib/libsec.so.1", "/lib/libsec.so.1", 1023) = 16
open("/lib/libsec.so.1", O_RDONLY) = 3
mmap(0xFEFB0000, 32768, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0xFEFB0000
mmap(0x00010000, 143360, PROT_NONE, MAP_PRIVATE|MAP_NORESERVE|MAP_ANON|MAP_ALIGN, -1, 0) = 0xFEA20000
mmap(0xFEA20000, 49583, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_TEXT, 3, 0) = 0xFEA20000
mmap(0xFEA3D000, 12029, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_INITDATA, 3, 53248) = 0xFEA3D000
mmap(0xFEA40000, 8392, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_ANON, -1, 0) = 0xFEA40000
munmap(0xFEA2D000, 65536) = 0
memcntl(0xFEA20000, 8828, MC_ADVISE, MADV_WILLNEED, 0, 0) = 0
close(3) = 0
xstat(2, "/usr/openwin/lib/libc.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libgen.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/lib/libgen.so.1", 0x08047268) = 0
resolvepath("/lib/libgen.so.1", "/lib/libgen.so.1", 1023) = 16
open("/lib/libgen.so.1", O_RDONLY) = 3
mmap(0xFEFB0000, 32768, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0xFEFB0000
mmap(0x00010000, 94208, PROT_NONE, MAP_PRIVATE|MAP_NORESERVE|MAP_ANON|MAP_ALIGN, -1, 0) = 0xFEA00000
mmap(0xFEA00000, 20573, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_TEXT, 3, 0) = 0xFEA00000
mmap(0xFEA16000, 1655, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_INITDATA, 3, 24576) = 0xFEA16000
munmap(0xFEA06000, 65536) = 0
memcntl(0xFEA00000, 5192, MC_ADVISE, MADV_WILLNEED, 0, 0) = 0
close(3) = 0
xstat(2, "/usr/openwin/lib/libc.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libpthread.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/lib/libpthread.so.1", 0x08047268) = 0
resolvepath("/lib/libpthread.so.1", "/lib/libpthread.so.1", 1023) = 20
open("/lib/libpthread.so.1", O_RDONLY) = 3
mmap(0xFEFB0000, 32768, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0xFEFB0000
munmap(0xFEFB3000, 20480) = 0
close(3) = 0
mmap(0x00000000, 4096, PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE|MAP_ANON, -1, 0) = 0xFE9F0000
xstat(2, "/usr/openwin/lib/libz.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/lib/libz.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/lib/libz.so.1", 0x08047268) = 0
resolvepath("/usr/lib/libz.so.1", "/usr/lib/libz.so.1", 1023) = 18
open("/usr/lib/libz.so.1", O_RDONLY) = 3
mmap(0x00010000, 32768, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_ALIGN, 3, 0) = 0xFE9E0000
mmap(0x00010000, 126976, PROT_NONE, MAP_PRIVATE|MAP_NORESERVE|MAP_ANON|MAP_ALIGN, -1, 0) = 0xFE9B0000
mmap(0xFE9B0000, 58404, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_TEXT, 3, 0) = 0xFE9B0000
mmap(0xFE9CE000, 2602, PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_INITDATA, 3, 57344) = 0xFE9CE000
munmap(0xFE9BF000, 61440) = 0
memcntl(0xFE9B0000, 4104, MC_ADVISE, MADV_WILLNEED, 0, 0) = 0
close(3) = 0
xstat(2, "/usr/openwin/lib/libm.so.2", 0x08047268) Err#2 ENOENT
xstat(2, "/lib/libm.so.2", 0x08047268) = 0
resolvepath("/lib/libm.so.2", "/lib/libm.so.2", 1023) = 14
open("/lib/libm.so.2", O_RDONLY) = 3
mmap(0xFE9E0000, 32768, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0xFE9E0000
mmap(0x00010000, 352256, PROT_NONE, MAP_PRIVATE|MAP_NORESERVE|MAP_ANON|MAP_ALIGN, -1, 0) = 0xFE950000
mmap(0xFE950000, 271027, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_TEXT, 3, 0) = 0xFE950000
mmap(0xFE9A2000, 14852, PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_INITDATA, 3, 270336) = 0xFE9A2000
munmap(0xFE993000, 61440) = 0
memcntl(0xFE950000, 23396, MC_ADVISE, MADV_WILLNEED, 0, 0) = 0
close(3) = 0
xstat(2, "/usr/openwin/lib/libsocket.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libnsl.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libc.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libc.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libnsl.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libc.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libc.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libc.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libc.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libavl.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/lib/libavl.so.1", 0x08047268) = 0
resolvepath("/lib/libavl.so.1", "/lib/libavl.so.1", 1023) = 16
open("/lib/libavl.so.1", O_RDONLY) = 3
mmap(0xFE9E0000, 32768, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0xFE9E0000
mmap(0x00010000, 73728, PROT_NONE, MAP_PRIVATE|MAP_NORESERVE|MAP_ANON|MAP_ALIGN, -1, 0) = 0xFE930000
mmap(0xFE930000, 2788, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_TEXT, 3, 0) = 0xFE930000
mmap(0xFE941000, 204, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_INITDATA, 3, 4096) = 0xFE941000
munmap(0xFE931000, 65536) = 0
memcntl(0xFE930000, 1056, MC_ADVISE, MADV_WILLNEED, 0, 0) = 0
close(3) = 0
xstat(2, "/usr/openwin/lib/libc.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libc.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/openwin/lib/libc.so.1", 0x08047268) Err#2 ENOENT
mmap(0x00000000, 4096, PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE|MAP_ANON, -1, 0) = 0xFE920000
mmap(0x00010000, 24576, PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE|MAP_ANON|MAP_ALIGN, -1, 0) = 0xFE910000
munmap(0xFE9E0000, 32768) = 0
getcontext(0x080477F0)
getrlimit(RLIMIT_STACK, 0x080477E8) = 0
getpid() = 28936 [28935]
lwp_private(0, 1, 0xFE912A00) = 0x000001C3
setustack(0xFE912A60)
sysconfig(_CONFIG_PAGESIZE) = 4096
sigfillset(0xFED34250) = 0
sysconfig(_CONFIG_SEM_VALUE_MAX) = 2147483647
sysi86(SI86FPSTART, 0xFED34BC0, 0x0000133F, 0x00001F80) = 0x00000001
close(3) Err#9 EBADF
openat(-3041965, "/proc/self/fd", O_RDONLY|O_NDELAY|O_LARGEFILE) = 3
fcntl(3, F_SETFD, 0x00000001) = 0
fstat64(3, 0x08046AD0) = 0
getdents64(3, 0xFE914000, 8192) = 144
getdents64(3, 0xFE914000, 8192) = 0
close(3) = 0
sysinfo(SI_PLATFORM, "i86pc", 256) = 6
sysinfo(SI_ARCHITECTURE, "i386", 256) = 5
uname(0x0808BE68) = 1
open64("/dev/smbios", O_RDONLY) = 3
stat64("/dev/xsvc", 0x08047600) = 0
fstat64(3, 0x08047690) = 0
pread64(3, " _ S M _B21F0203CC\0\0\0".., 31, 0) = 31
pread64(3, " _ S M _B21F0203CC\0\0\0".., 31, 0) = 31
sysconfig(_CONFIG_NPROC_ONLN) = 4
issetugid() = 0
issetugid() = 0
brk(0x0809D000) = 0
brk(0x080AD000) = 0
pread64(3, "\018\0\00102\0F0030F90DA".., 3069, 32) = 3069
close(3) = 0
getpid() = 28936 [28935]
brk(0x080BD000) = 0
sysconfig(_CONFIG_PAGESIZE) = 4096
access("/usr/lib/fm/fmd/fmd.conf", F_OK) Err#2 ENOENT
access("/usr/platform/i86pc/lib/fm/fmd/fmd.conf", F_OK) Err#2 ENOENT
access("/usr/platform/i86pc/lib/fm/fmd/fmd.conf", F_OK) Err#2 ENOENT
access("/etc/fm/fmd/fmd.conf", F_OK) Err#2 ENOENT
brk(0x080CD000) = 0
sigaction(SIGTERM, 0x08047B90, 0x00000000) = 0
corectl(CC_SET_PROCESS_PATH, "/var/fm/fmd/core.fmd.%p", 24, 28936) = 0
setrlimit(RLIMIT_CORE, 0x080477A0) = 0
getprivimplinfo(0x08046AF0, 2076) = 0
mmap(0x00010000, 65536, PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE|MAP_ANON|MAP_ALIGN, -1, 0) = 0xFE8F0000
sysconfig(_CONFIG_NGROUPS) = 16
zone_lookup("") = 0
zone_getattr(0, ZONE_ATTR_PRIVSET, 0xFE910288, 12) = 12
setgroups(0, 0x00000000) = 0
setgid(0) = 0
getppriv(PRIV_PERMITTED, {ffffffffffffffffffffffff}) = 0
setppriv(PRIV_SET, PRIV_EFFECTIVE, {ffffffffffffffffffffffff}) = 0
setreuid(0, 0) = 0
setppriv(PRIV_SET, PRIV_LIMIT, {00f60043b858500000000000}) = 0
setppriv(PRIV_SET, PRIV_PERMITTED, {00f60043b858500000000000}) = 0
setppriv(PRIV_SET, PRIV_INHERITABLE, {00f60043b858500000000000}) = 0
getpid() = 28936 [28935]
corectl(CC_GET_PROCESS_PATH, "/var/fm/fmd/core.fmd.%p", 1024, 28936) = 0
setpflags(8, 0) = 0
schedctl() = 0xFE8E1000
lwp_sigmask(SIG_SETMASK, 0xFFBFFEDF, 0x0000FFF7) = 0xFFBFFEFF [0x0000FFFF]
pipe() = 3 [4]
fork1() = 28937
lwp_sigmask(SIG_SETMASK, 0xFFBFFEDF, 0x0000FFF7) = 0xFFBFFEFF [0x0000FFFF]
close(4) = 0
read(3, 0x08047BD8, 4) (sleeping...)
read(3, 0x08047BD8, 4) = 0
waitid(P_PID, 28937, 0x080476E0, WEXITED|WTRAPPED) = 0
_exit(1)
[root@qbi-mdcprod:/var/tmp] $ cat fmd.out
execve("/usr/lib/fm/fmd/fmd", 0x08047C58, 0x08047C60) argc = 1
resolvepath("/usr/lib/ld.so.1", "/lib/ld.so.1", 1023) = 12
resolvepath("/usr/lib/fm/fmd/fmd", "/usr/lib/fm/fmd/fmd", 1023) = 19
sysconfig(_CONFIG_PAGESIZE) = 4096
xstat(2, "/usr/lib/fm/fmd/fmd", 0x08047A38) = 0
open("/var/ld/ld.config", O_RDONLY) Err#2 ENOENT
mmap(0x00000000, 4096, PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE|MAP_ANON, -1, 0) = 0xFEFC0000
xstat(2, "/usr/openwin/lib/libtopo.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/lib/fm/libtopo.so.1", 0x08047268) = 0
resolvepath("/usr/lib/fm/libtopo.so.1", "/usr/lib/fm/libtopo.so.1", 1023) = 24
open("/usr/lib/fm/libtopo.so.1", O_RDONLY) = 3
mmap(0x00010000, 32768, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_ALIGN, 3, 0) = 0xFEFB0000
mmap(0x00010000, 172032, PROT_NONE, MAP_PRIVATE|MAP_NORESERVE|MAP_ANON|MAP_ALIGN, -1, 0) = 0xFEF80000
mmap(0xFEF80000, 97805, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_TEXT, 3, 0) = 0xFEF80000
mmap(0xFEFA8000, 4642, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_INITDATA, 3, 98304) = 0xFEFA8000
munmap(0xFEF98000, 65536) = 0
memcntl(0xFEF80000, 14992, MC_ADVISE, MADV_WILLNEED, 0, 0) = 0
close(3) = 0
xstat(2, "/usr/openwin/lib/libdiagcode.so.1", 0x08047268) Err#2 ENOENT
xstat(2, "/usr/lib/fm/libdiagcode.so.1", 0x08047268) = 0
resolvepath("/usr/lib/fm/libdiagcode.so.1", "/usr/lib/fm/libdiagco
Similar Messages
-
System Image Restore Fails "No disk that can be used for recovering the system disk can be found"
Greetings
- Our critical server image backup Fails on one
server -
Two 2008 R2 servers. Both do a nightly "Windows Server Backup" of Bare Metal Recovery, System State, C:, System Reserved partition, to another storage hard drive on the same machine as the source. Active Directory is on the C: The much larger D: data
partition on each source hard drive is not included.
Test recovery by disconnecting 500G System drive, booting from 2008R2 Install DVD, recovering to a new 500G SATA hard drive.
Server A good.
Server B fails. It finds the backed-up image, & then we can select the date we want. As soon as the image restore is beginning and the timeline appears, it bombs with "The system image restore failed. No disk that can be used for recovering the system
disk can be found." There is a wordy Details message but none of it seems relevant (we are not using USB etc).
At some point after this, in one (or two?) of the scenarios below, (I forget exactly where) we also got :
"The system image restore failed. (0x80042403)"
The destination drive is Not "Excluded".
Used diskpart clean to remove volumes from destination drive. Recovery still errored.
Tried a second restore-to drive, same make/model Seagate ST3500418AS, fails.
Tried the earliest dated B image rather than the most recent, fail.
The Server B backups show as "Success" each night.
Copied image from B to the same storage drive on A where the A backup image is kept, and used the A hardware to attempt restore. Now only the latest backup date is available (as would occur normally if we had originally saved the backup to a network location).
Restore still fails. It looks like its to do with the image rather than with the hardware.
Tried unticking "automatically check and update disk error info", still fail.
Server A SRP 100MB C: 50.6GB on Seagate ST3500418AS 465.76GB Microsoft driver 6.1.7600.16385 write cache off
Server B SRP 100MB C: 102GB on Seagate ST3500418AS 465.76GB Microsoft driver 6.1.7600.16385 write cache off
Restore-to hard drive is also Seagate ST3500418AS.
http://social.answers.microsoft.com/Forums/en-US/w7repair/thread/e855ee43-186d-4200-a032-23d214d3d524 Some people report success after diskpart clean, but not us.
http://social.technet.microsoft.com/Forums/en-US/windowsbackup/thread/31595afd-396f-4084-b5fc-f80b6f40dbeb
"If your destination disk has a lower capacity than the source disk, you need to go into the disk manager and shrink each partition on the source disk before restoring." Doesnt apply here.
http://benchmarkreviews.com/index.php?option=com_content&task=view&id=439&Itemid=38&limit=1&limitstart=4
for 0x80042403 says "The solution is really quite simple: the destination drive is of a lower capacity than the image's source drive." I cant see that here.
Thank you so much.Hello,
1. While recovering the OS to the new Hard disk, please don't keep the original boot disk attached to the System. There is a Disk signature for each hard disk. The signature will collide if the original boot disk signature is assigned to the new disk.
You may attach the older disk after recovering the OS. If you want to recover data to the older disk then they should be attached as they were during backup.
2. Make sure that the new boot disk is attached as the First Boot disk in hardware (IDE/SATA port 0/master) and is the first disk in boot order priority.
3. In Windows Recovery Env (WinRE) check the Boot disk using: Cmd prompt -> Diskpart.exe -> Select Disk = System. This will show the disk where OS restore will be attempted. If the disk is different than the intended 2 TB disk then swap the disks in
correct order in the hardware.
4. Please make sure that the OS is always recovered to the System disk. (Due to an issue: BMR might recover the OS to some other disk if System disk is small in size. Here the OS won't boot. If you belive this is the case, then you should attach the
bigger sized disk as System disk and/or exclude other disks from recovery). Disk exclusion is provided in System Image Restore/Complete PC Restore UI/cmdline.
5. Make sure that Number and Size of disks during restore match the backup config. Apart from boot volumes, some other volumes are also considered critical if there are services/roles installed on them. These disks will be marked critical for recovery and
should be present with minimum size requirement.
6. Some other requirements are discussed in following newsgroup threads:
http://social.technet.microsoft.com/Forums/en-US/windowsbackup/thread/871a0216-fbaf-4a0c-83aa-1e02ae90dbe4
http://social.technet.microsoft.com/Forums/en-US/windowsbackup/thread/9a082b90-bd7c-46f8-9eb3-9581f9d5efdd
http://social.technet.microsoft.com/Forums/en-US/windowsbackup/thread/11d8c552-a841-49ac-ab2e-445e6f95e704
Regards,
Vikas Ranjan [MSFT]
------- This information is provided as-is without any warranties, implicit or explicit.------- -
Is it possible to change your default video transition?
You can save a transition you want to use a lot as a "Favorite" and then it is easily accessible for frequent use.
Ian. -
I have a macbook pro and I want to use my canon firewire digital video camera on yahoo chat. When I sign on to chat and attempt to use a camera, the system automatically defaults to the built in camera on the notebook. Can I override that default?
You have 10.6 on that machine, I suggest you stick with it for performance, third party hardware and software reasons as long as possible.
Consider 10.8 (not 10.7) when it's released, because 10.7 and 10.8 will require a new investment in software and newer third party hardware as it requires newer drivers the old machines won't have. (forced upgrade because of software, really nice of them)
http://roaringapps.com/apps:table
Far as your Safari problem do these things until it's resolved:
1: Software Update fully under the Apple menu.
2: Check the status of your plug-ins and update (works for all browsers) also install Firefox and see if your problems continue. You should always have at least two browsers on the machine just in case one fails.
https://www.mozilla.org/en-US/plugincheck/
Flash install instructions/problem resolution here if you need it.
How to install Flash, fix problems
3: Install Safari again from Apple's web site
https://www.apple.com/safari/
4: Run through this list of fixes, stopping with #16 and report back before doing #17
Step by Step to fix your Mac -
i have a 10.6.8 mac os x system in a intel processor computer. how can I addressbook contacts to icloud. I tried exporting my import my addressbook and failed, then exportind a vcard from all contacts and failed and finale only one vcadr and failed. Something might i doing wrong
I just had the same problem, I've updated to 10.6.8 yesterday, and since then the browsing are very slow, no matter what broswer I am using, the upload download speed are still the same. But browsing just take forever, It takes for example google.com 30 seconds to load. I have Extream high speed internet connection, 3 other computers, and the only one is having this problem is the Mac after the update.
Something in this update screwed my browsing capabitilties, I tried downloading Crome browser, same issue.
I hope there is a way beside TimeMachine to revert the latest update. I don't want to reformat as I am sure as soon as I am going to do the update it will cause the same problem.
Model Name: iMac
Model Identifier: iMac11,3
Processor Name: Intel Core i7
Processor Speed: 2.93 GHz
Number Of Processors: 1
Total Number Of Cores: 4
L2 Cache (per core): 256 KB
L3 Cache: 8 MB
Memory: 12 GB
Processor Interconnect Speed: 4.8 GT/s
Boot ROM Version: IM112.0057.B00 -
Can't Reset Default Audio Transition
My default audio transition (cross fade) has been replaced by "None" and I can't select "Set Default" to reset it. I've tried manually applying the transition then selecting it but "Set Default" is still grayed out. I first noticed the problem when the shortcut optioncommandT stopped working.
This has been driving me nuts for a while now I'm hoping someone can tell me how the default could get deleted and how to reset it.
I'm running FCP 5.04 on a Dual 2GHz G5 PowerPC.
Thanks,
ShelbyI still don't know if this can be done from the Effects drop down menu but I was able to reset the default in the Effects tab in the Browser window, which I rarely use.
Thanks. -
System/webconsole:console failed fatally
Getting a failed service every time I boot that I can't seem to fix. Here is the error message:
Jun 3 12:24:14 rhea svc.startd[7]: system/webconsole:console failed fatally: transitioned to maintenance (see 'svcs -xv' for details)
I've tried looking at a few things, but I'm not sure what to try next. Any advice would be greatly appreciated. Here are the pertinent log files and svcs information:
bash-3.00# svcs -xv
svc:/application/print/server:default (LP print server)
State: disabled since Tue Jun 03 12:23:13 2008
Reason: Disabled by an administrator.
See: http://sun.com/msg/SMF-8000-05
See: man -M /usr/share/man -s 1M lpsched
Impact: 2 dependent services are not running:
svc:/application/print/rfc1179:default
svc:/application/print/ipp-listener:default
svc:/system/webconsole:console (java web console)
State: maintenance since Tue Jun 03 12:24:14 2008
Reason: Start method exited with $SMF_EXIT_ERR_FATAL.
See: http://sun.com/msg/SMF-8000-KS
See: man -M /usr/share/man -s 1M smcwebserver
See: /var/svc/log/system-webconsole:console.log
Impact: This service is not running.
bash-3.00# vi /var/svc/log/system-webconsole:console.log
[ May 30 17:01:09 Disabled. ]
[ May 30 17:01:09 Rereading configuration. ]
[ May 30 17:01:56 Enabled. ]
[ May 30 17:03:11 Executing start method ("/lib/svc/method/svc-webconsole start") ]
Starting Sun Java(TM) Web Console Version 3.0.2 ...
The console is running.
[ Jun 3 07:56:57 Executing start method ("/lib/svc/method/svc-webconsole start") ]
Starting Sun Java(TM) Web Console Version 3.0.2 ...
org.xml.sax.SAXParseException: Content is not allowed in prolog.
at com.sun.org.apache.xerces.internal.util.ErrorHandlerWrapper.createSAX
ParseException(ErrorHandlerWrapper.java:236)
at com.sun.org.apache.xerces.internal.util.ErrorHandlerWrapper.fatalError(ErrorHandlerWrapper.java:215)
at com.sun.org.apache.xerces.internal.impl.XMLErrorReporter.reportError(XMLErrorReporter.java:386)
at com.sun.org.apache.xerces.internal.impl.XMLErrorReporter.reportError(XMLErrorReporter.java:316)
at com.sun.org.apache.xerces.internal.impl.XMLScanner.reportFatalError(XMLScanner.java:1438)
at com.sun.org.apache.xerces.internal.impl.XMLDocumentScannerImpl$PrologDispatcher.dispatch(XMLDocumentScannerImpl.java:899)
"system-webconsole:console.log" 260 lines, 24468 characters (56 null)what about:
mkdir -p /usr/java/bin
cd /usr/java/bin
ln -s `which java`.
.7/M. -
System/webconsole:console fail fatally
Hi everyone,
please could you help me resolve this challenging issue encountered on SunOS Release 5.10 Version Generic_125100-09 64-bi at the client site,
the error is stated below
svc.startd[7]: system/webconsole:console fail
ed fatally: transitioned to maintenance (see 'svcs -xv' for details)FYI.
# svcs -l svc:/system/webconsole:console
fmri svc:/system/webconsole:console
name java web console
enabled true
state maintenance
next_state none
state_time Thu Jul 24 08:14:17 2008
logfile /var/svc/log/system-webconsole:console.log
restarter svc:/system/svc/restarter:default
contract_id
dependency require_all/none svc:/milestone/multi-user (online)
# tail /var/svc/log/system-webconsole:console.log
Shutting down Sun Java(TM) Web Console Version 3.0.2 ...
[ Jul 24 07:50:21 Enabled. ]
[ Jul 24 08:06:33 Executing start method ("/lib/svc/method/svc-webconsole start") ]
Starting Sun Java(TM) Web Console Version 3.0.3 ...
[ Jul 24 08:11:34 Method or service exit timed out. Killing contract 233 ]
[ Jul 24 08:11:34 Method "start" failed due to signal KILL ]
[ Jul 24 08:11:34 Executing start method ("/lib/svc/method/svc-webconsole start") ]
Starting Sun Java(TM) Web Console Version 3.0.3 ...
The console failed to start.
[ Jul 24 08:14:13 Method "start" exited with status 95 ]
# /usr/sbin/smcwebserver status
Sun Java(TM) Web Console is running
# /usr/sbin/smcwebserver stop
Shutting down Sun Java(TM) Web Console Version 3.0.3 ...
The console is stopped
# ps -efZ | grep java
PUBLIC root 800 26592 1 09:07:19 console 0:00 grep java
PUBLICnoaccess 14403 1737 0 08:36:28 ? 2:02 /usr/java/bin/java -server -Xmx128m -XX:+BackgroundCompilation -XX:PermSize=32m
# kill -15 14403
# ps -efZ | grep java
PUBLIC root 806 26592 1 09:08:17 console 0:00 grep java
# /usr/sbin/smcwebserver status
Sun Java(TM) Web Console is stopped
# /usr/sbin/smcwebserver start
Starting Sun Java(TM) Web Console Version 3.0.3 ...
The console is running
# /usr/sbin/smcwebserver status
Sun Java(TM) Web Console is running
# ps -efZ | grep java
PUBLIC root 1176 26592 1 09:12:22 console 0:00 grep java
PUBLICnoaccess 983 1737 6 09:10:47 ? 1:00 /usr/java/bin/java -server -Xmx128m -XX:+BackgroundCompilation -XX:PermSize=32m
# svcs -l svc:/system/webconsole:console
fmri svc:/system/webconsole:console
name java web console
enabled true
state online
next_state none
state_time Thu Jul 24 09:11:38 2008
logfile /var/svc/log/system-webconsole:console.log
restarter svc:/system/svc/restarter:default
contract_id 242
dependency require_all/none svc:/milestone/multi-user (online)
# -
Hard drive on HP notebook PC failed. After replacement, can I upgrade OS and memory?
I have an HP Pavilion Entertainment Notebook PC, Model dv9617nr (HP pn GS730UA). An error message on boot-up says "Operating System not found" so my Windows Vista Ultimate 32-bit (upgraded two years ago) will not load. I am assuming this means that my hard drive has failed. How can I verify this assumption? Again, assume I am correct, and I order the recommended replacement (HP pn 590736-001) from SpareParts Warehouse ($142.50 plus shipping). Are there instructions on the internet for doing this replacement? After I do this replacement, I thought I could install Windows 7 I already have and upgrade the memory to 4GB SODIMM from the 1GB SODIMM that was originally used. What problems would I have with Hardware Compatibility using Windows 7? If the memory module I use has the same specs as the HP recommended replacement (HP pn 598861-001), i.e. 800MHz, 200 pin, PC2-6400, SDRAM, but a larger 4GB memory capacity, would I have any compatibility problems using it? Please advise me on these issues. Thanks, Jeff
This question was solved.
View Solution.Hi, Jeff:
Let me break down your question...
First, to confirm your HDD died, go into your BIOS menu. There should be a hard drive and memory diagnostics utility. Run the HDD diagnostics utility and see what it reports. More than likely the HDD has crashed and is no longer usable.
You can order a replacement drive or you can get any SATA II hard drive --either 5400 RPM or 7200 RPM.
You could go to 250 to 500 GB if you choose. Unfortunately right now, HDD prices are unreasonably high due to the flooding in Thailand where many HDD manufacturing plants are located. Some were damaged heavily, causing HDD prices to triple almost overnight.
This is a drive you can get that I think is better than what you have now: This one is 7,200 RPM. Faster but uses more battery power.
http://www.newegg.com/Product/Product.aspx?Item=N82E16822136279
You can get the 5400 rpm version too...similar. Not as good as the caviar black. This is more along the line of what you would get from HP.
http://www.newegg.com/Product/Product.aspx?Item=N82E16822136387
Read the reviews on both or you are free to get the one from HP.
There are instructions to install the hard drive and memory on your notebook's support and driver page. Click on Manuals on the right side of the page.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01278446&tmp_task=prodinfoCategory&cc=us&dlc=en...
Then you want to look at the maintenance and service guide.
You can upgrade the memory to a maximum of 4 GB using 2 x 2GB of PC2-6400 memory. You can get it from HP or you can get it at the link below. This is the memory I use. As a matter of fact I just ordered this very same memory to install in my sister-in-law's dv6700.
http://www.newegg.com/Product/Product.aspx?Item=N82E16820148159
Now, you can install W7 just fine. I installed W7 Home Premium 64 bit on my dv6810us that has pretty much the same hardware as yours and 4 GB of memory (the same as I posted above).
Here is the catch though. It depends on what version of W7 you have. If you have a W7 upgrade version, you must install a qualifying operating system on the hard drive before you can upgrade it.
If you have a full version of Windows 7, then you can install it on a blank hard drive.
If you have the upgrade version, contact HP support and order a set of Vista recovery disks. Install Vista and then uprade to W7 if you have the upgrade version of W7.
You can use the vista drivers from your notebook's support page for any drivers you need that W7 didn't supply.
One thing...DO NOT flash (update) the BIOS when running Windows 7. You can only flash it using windows vista.
Hope this helps. If you have any other questions, please let us know.
Paul -
Warning: The system has not been taken off maintenance mode completely
After I enabled Maintenance mode using adadmin, I ran Compile Flexfields. Then I disabled Maintenance mode. But, on the 11i login page, I keep getting a warning message:
Warning
The system has not been taken off maintenance mode completely. Please contact your System Administrator.
I am sure I disabled the Maintenance mode in adadmin. Why I still get the warning? How to fix it? Thanks a lot.Thanks a lot. That is the fix.
One more question. After I ran "Compile Flexfields", I got
Number of successful descriptive flex compilations : 7520
Number of failed descriptive flex compilations : 1
How can I find the failed description flex? The log does not give info on this. And, how to fix it?
Thanks a lot for your help. -
Failed configuring Portal Server. can't run cacaoadm.bat
Hi,
I am trying to install Sun Java ES5 (2006Q4) on window XP. The configuration for portal server was failed. When I checked the logs, it complains cacao default instance was disabled and couldn't started. I went to the the directory and tried to manually run cacaoadm command. It returns:
C:\Sun\JavaES5\share\cacao_2\bin>cacaoadm.bat enable
This action cannot be performed by a non privileged user.
I logged on to the windows as a user who is in the administrators group. Any other components installations were fine. I really have no idea how to solve this problem as there is no user account as administrator. Can someone please help?
The portal config error from the log are as following:
[#|2007-06-26T15:22:14.821+1000|INFO|SJS Portal Server|debug.com.sun.portal.fabric.config|ThreadID=10; ClassName=com.sun.portal.fabric.config.PortalConfigurator; MethodName=configureHost; |PSFB_CSPFC0021:Waiting for Cacao Server to Startup|#]
[#|2007-06-26T15:22:15.696+1000|FINEST|SJS Portal Server|debug.com.sun.portal.fabric.util|ThreadID=37; ClassName=com.sun.portal.fabric.util.StreamLogger; MethodName=run; |PSFB_CSPFU0004: C:/Sun/JavaES5/share/cacao_2/bin/cacaoadm(Output)=default instance is DISABLED at system startup.|#]
[#|2007-06-26T15:22:15.712+1000|FINEST|SJS Portal Server|debug.com.sun.portal.fabric.util|ThreadID=37; ClassName=com.sun.portal.fabric.util.StreamLogger; MethodName=run; |PSFB_CSPFU0004: C:/Sun/JavaES5/share/cacao_2/bin/cacaoadm(Output)=default instance is not running.|#]
[#|2007-06-26T15:22:15.790+1000|INFO|SJS Portal Server|debug.com.sun.portal.fabric.tasks|ThreadID=10; ClassName=com.sun.portal.fabric.tasks.Cacao; MethodName=execCommand; |PSFB_CSPFT0342:<C:/Sun/JavaES5/share/cacao_2/bin/cacaoadm status> Returned <default instance is DISABLED at system startup.
default instance is not running.
|#][#|2007-06-26T15:23:45.790+1000|SEVERE|SJS Portal Server|debug.com.sun.portal.fabric.config|ThreadID=10; ClassName=com.sun.portal.fabric.config.PortalConfigurator; MethodName=configureHost; |PSFB_CSPFC0020:Cacao Server startup failed|#]
[#|2007-06-26T15:23:45.790+1000|SEVERE|SJS Portal Server|debug.com.sun.portal.fabric.config|ThreadID=10; ClassName=com.sun.portal.fabric.config.PortalConfigurator; MethodName=configureHost; |PSFB_CSPFC0024:Failed to configure the Host
com.sun.portal.fabric.tasks.ConfigurationException
at com.sun.portal.fabric.config.PortalConfigurator.configureHost(PortalConfigurator.java:635)
at com.sun.portal.fabric.config.ConfigurePortal.main(ConfigurePortal.java:166)
|#]
[#|2007-06-26T15:23:45.790+1000|SEVERE|SJS Portal Server|debug.com.sun.portal.fabric.config|ThreadID=10; ClassName=com.sun.portal.fabric.config.ConfigurePortal; MethodName=main; |PSFB_CSPFC0014:Failed configuring Portal Server!!
com.sun.portal.fabric.tasks.ConfigurationException: com.sun.portal.fabric.tasks.ConfigurationException
at com.sun.portal.fabric.config.PortalConfigurator.configureHost(PortalConfigurator.java:749)
at com.sun.portal.fabric.config.ConfigurePortal.main(ConfigurePortal.java:166)
Thank you very much
Regards,
TaraHi Deepak,
Thanks for the post.
Use cacaoadm restar gives me the same error.
I found out that is a limitation for the windows version I am using. Basically, the account for installation and configuration has to be an local administrator not in network.
Cheers,
Tara -
"Program terminated in remote system NONE: Logon failed" when adding a new table
Hello,
I set up a replication flow from a SAP ERP 6.0 EHP7 with SAP ASE 16.0 source to SAP HANA 1.0 rev 82 target
I am using a standalone SLT system NetWeaver 7.0 with DMIS 2011_1_731 (with SP 1 to 7).
I have 100 tables to replicate.
I succeeded to set up replication for 57 tables. These tables are replicating properly.
Whenever I try to add a new one (with LTRC transaction, Data Provisioning -> Start Replication), the new table is marked as 'Failed' after a little while.
When I press 'Show Error Log' button I got an obscure error message:
"Program terminated in remote system NONE: Logon failed "
I do not understand this message. I checked both on SAP ASE source and SAP HANA target. I am still able to connect against both source and target.
Can you please tell how to troubleshoot this error.
Thanks in advance,
ChristianFirst thank you for answering my questions. I really appreciate your answers.
I rechecked the documentation.
"Application Operations Guide SAP Landscape Transformation Replication Server Document Version: 2.3 – 2014-07-08"
Page 29 - 30
3.5.2.2 Data Transfer Jobs
This section explains the relationship between the number of data transfer jobs and the number of available background work process.
Data transfer and data transformation processing on SLT server system is accomplished by the background work processes of the underlying SAP NetWeaver ABAP application server. Each job occupies 1 background work process in the SAP LT Replication Server system. For each configuration, the parameter Data Transfer Jobs restricts the maximum number of data load job for each mass transfer ID (MT_ID). In total, a mass transfer ID (MT_ID) requires at least 4 background jobs to be available:
One monitoring job (master job)
One master controller job
At least one data load job
One additional job either for the migration objects definition, access plan calculation or to change configuration settings in the Configuration & Monitoring Dashboard
Example
If you set the parameter Data Transfer Jobs to 04 in a configuration “SCHEMA1”, a mass transfer ID 001 is assigned. As a result, the following jobs should be in the system:
1 Master controller job: /1LT/IUC_REP_CNTR_001
At most 4 parallel jobs for MT_ID 001: /1LT/IUC_LOAD_MT_001_001/~002/~003/~004
When configuring your data load or replication scenario, consider the following:
Do not define more data transfer jobs than the number of available application server background work processes. If all available background work processes are already occupied by jobs, any other job will have to wait until a free work process becomes available. This can lead to long wait times until a new activity (for example creating triggers) can start, and can also result in significantly increased latency times for data replication.
The number of dialog work processes in the source system corresponds 1:1 with the number of data transfer jobs in the SAP LT Replication Server system.
Besides the work processes allocated by the data transfer jobs you need to provide additional available work processes for controller and monitoring jobs, the migration objects definition, access plan calculation or to perform configuration changes, and so on.
Sizing for SAP LT Replication Server involves determining how many work processes are required to perform the initial load of data into the target system within an acceptable timeframe, and accomplish the change capturing and the transfer of data changes to the target system within expected latency times.
Ensure that you add enough additional work processes to allow other required SAP LT Replication Server jobs to run.
Finally, you map the number of required application server work processes to their system resource consumption (CPU, memory, disc space) using the formulas provided by the SLT Sizing Guide.
With the simple formula below, you can calculate the number of required application server work processes (WPs) on the SLT Server for each active SLT configuration.
The number of required work processes can be determined by adding
The Number of required data transfer jobs ,
plus one background work process for Central Master (Monitoring) Job (only one per system!),
plus one background work process for Master Controller Job,
plus 3-5 additional empty background work processes (recommended per configuration),
plus approx. 3 dialog work processes (recommended for each configuration).
Note: A lack of available free application server work processes can negatively affect the data load or data replication processes.
To summarize everything, the number of 'Data Transfer Jobs' must be set depending of the number of source tables, it is not the actual number of tables.
Assume that for my 100 tables I use 10 'Data Transfer Jobs' :
- The number of work processes on the SLT server would be 20. I took the simple formula of the documentation:
10 data transfer jobs ,
+ 1 background work process for Central Master (Monitoring) Job (only one per system!),
+ 1 background work process for Master Controller Job,
+ 5 additional empty background work processes (recommended per configuration),
+ 3 dialog work processes (recommended for each configuration).
- The number of dialog processes on the source server would be 10 ( equal to the number of 'Data Transfer Jobs')
Am I correct ?
Regards,
Christian -
How do I connect my Home Theatre System to Apple TV such that I Can Play the Music on my iPhone through the Home Theatre System?
Thanks for the reply. I tried but failed. There's no sound through the Home Theatre system ( Bose 3.2.1 GS). The audio audio always come through the TV which is connected to the ATV. Please help. Thanks
-
I tried to create a new google calendar in ical, but they did not show up, I tried this several times.
Now when I sync my iPad via iTunes all these failed attempts are showing up under the ical sync list in iTunes, how can I clear them from this list?See https://bugs.downthemall.net/ticket/2147
Google Search Bug
Reported by: openid:nathan wride Owned by:
Priority: major Milestone:
Component: Polish/Usability Version: 2.0.10
Keywords: Google search instant save bug Cc:
Operating System: Windows
Description
Hi Guys
I have found a bug/annoying thing that occurs frequently on google. When searching, DTA trys to download the search...
I'll try to attach a screenshot.
Attachments
[https://bugs.downthemall.net/attachment/ticket/2147/Screenshot.png Screenshot.png] Download (113.0 KB) - added by openid:nathan wride 4 weeks ago.
The screenshot that shows the bug. -
SSRS report throwing error :- system.web.aspnethostingpermission failed
Hi,
I am facing an issue with SSRS report after implementing HTTPHandler in its web.config file of Report manager.
My reports were working fine. I deployed a dll in report manager BIN folder and added below tag in the web.config
<add verb="*" path="*.aspx" type="ISHandler.SyncHandler, ISHandler" />
ISHandler is the assembly/namespace and SyncHandler is the class name.
I am getting error when I try to access the report
error :- system.web.aspnethostingpermission failed.
Currently web.config contains below settings.
<securityPolicy>
<trustLevel name="RosettaMgr" policyFile="rsmgrpolicy.config" />
</securityPolicy>
<trust level="RosettaMgr" originUrl="" />
Can you please help where the security permission is missing ?
sanmayI am unable to see that. Please check.
sanmay
Maybe you are looking for
-
How do I get an new 10.3 client license
I have an iMac G3 (Ruby w/ slot-load CD drive, & USB) that I believe to be 10.3 compatible based on docs here in Apple.com (am I right about that?). I'm handing this down to the grandkids, so I don't need to spend the money for a full 10.4 and go thr
-
Google search results won't open automatically new tab in firefox 6.0.2
Clicking on google search results won't open automatically new tabs in firefox 6.0.2, although it was working until today!
-
How many characters can be in filenames
There seems to be a difference in how the MAC and PC handle filename length in our photo department. Is there a maximum character length for filenames. Where does one find out this kind of information?
-
Zero Block Corruption in SE Environment.
Environment: 11g Using Standard Edition of Rracle in Windows environment. I'm having difficulties finding any article or support documents for Zero block corruption issues at logical level. If i took Export of the full database, and have no errors. d
-
hi, i need to get the WSDL document that describes the service that the user selects. but some how, my codes now does get a WSDL document but it does not describes the web seervice... more like describing the organization... the following is my codes