The current i/o channels

i have ni6229
what is maximum current for digital output channel
whatis the solution for :
if i need use mechanical relay (input volt 5 vDc) but it has input current grater then 20 mA

Hello engmoh,
The maximum current for the digital output channels on the 6229 can be found in the following KnowledgeBase article:
http://digital.ni.com/public.nsf/websearch/383AE78B7744B3E686256F26005B3F42?OpenDocument
The information in that article can be found in the M Series Help which can be found here:
http://digital.ni.com/manuals.nsf/websearch/9477D6DF1FE5A72986256FAB00633DE4?opendocument
I hope this helps!
E.Lee
Eric
DE For Life!

Similar Messages

Which is the best wi-fi channel to use if I'm getting interference

According to my network settings, the current wi-fi channel is 802.11g. In the past I have had no trouble with wi-fi transmissions in the house but recently I have been having trouble with the wi-fi connection between my computer and my Apple TV. The picture and sound on my computer screen is sometimes 'delayed' on the TV and/or the TV screen becomes grossly pixelated and then often just freezes. I have searched the internet for possible reasons for this and wonder whether my problems are related to my neighbour just having had a baby (apparently baby monitors can be a cause of wi-fi interference). If a device such as a baby monitor is causing my recent and ongoing wi-fi problems, what can I do to fix this? I have read somewhere that changing the wi-fi channel to 802.11n might improve things (5GHz?) but I am not game to manually re-set my Airport Express just on the offchance that things might improve because I am worried that I might do something wrong and completely muck up my wireless set-up. Has anyone similar problems and can anyone give me some advice as to what I should do?

According to my network settings, the current wi-fi channel is 802.11g.
Wi-Fi operates on two different radio bands: 2.4 & 5 GHz. Around these two bands are several radio modes: 802.11a, 802.11b, 802.11g, 802.11n, & the latest, 802.11ac. These modes operate on one band or the other with the exception of 801.11n which can operate on either. Finally, each band has a set number of frequencies (radio channels) that can be used. Which channels are dependent on where you live. In the US, the 2.4 GHz band uses channels 1-11. For the 5 GHz band, there are two segments of channels and your AirPort Express can access four channels in each of these segments: 36, 40, 44, 48, & 149, 153, 157, 161
With that said, currently the 5 GHz band is less "crowded" than the 2.4 GHz band ... and thus, less chance of issues with Wi-Fi interference. If your current radio mode is set to 802.11g then it is operating on the 2.4 GHz band. Changing to 802.11n may help as it, again, can operate on either. The important thing to take from this is that the higher frequency band has more difficulty traveling over longer distance and through objects like walls ... so you are pretty much limited to either a single room or to the immediatly adjacent rooms when using this band.
There are a number of things to try:
Determine if there is other forms of Wi-Fi interference in the area. If they are caused by other Wi-Fi operating nearby you will want to change the radio mode's channel to be at least 3-5 channels away from the other Wi-Fi that has the strongest signal. To determine if other Wi-Fis are nearby you can use utilities like iStumbler, or AirRadar to find them, and then, radio channel on your network to reduce the interference. If switching channels resolves the problem you don't need to go on to the next option.
Switch the radio mode from 802.11g to 802.11n. Which exact radio mode you will want to use will depend on two things: 1) Will you still need to support non-802.11n wireless clients, and 2) Which exact model of the AirPort Express that you have. If you can provide both of these, I can offer a recommendation on what radio mode to try.

I have a FP-1600 and a FP-AO-200 module, 0-20 ma. When I use Field Point Explorer 3.0.1, I can not command any of the channel output current. The current remains in the lowest value 0.0035 A. What is the problem ?

I have a FP-1600 and a FP-AO-200 module, 0-20 ma. When I use Field Point Explorer 3.0.1, I can not command any of the channel output current. The current remains in the lowest value 0.0035 A. What is the problem ? The communications with the module are OK, because it shows when the current are open or closed.

Jorg,
I noticed that you claimed to be using the module in 0-20mA mode, yet the reading you are seeing is 3.5mA. This is the minimum value (with overranging) when the module is set to 4-20mA mode. My guess is that your module is defaulting back to 4-20mA mode, but your IAK file still thinks the module is in 0-20mA mode. You can verify this by using the find devices button in FieldPoint Explorer and then trying to write to the channel.
To fix this problem, you should use the snapshot feature to change the default power-up mode for that channel.
Regards,
Michael Shasteen
Applications Engineering
National Instruments
www.ni.com/ask
1-866-ASK-MY-NI

Details of open invoices for the current year/ material price analysis

Hi,
I'm very new to SAP SD,MM modules. Can any one help me in the following of my requirements?
1. How to get the details of open invoices for the current year? Which table should I look into?
2. I have to create a report to display material price analysis. How should I do that?
3. How to develope a report to list out all the Open Sales Order with earliest ship date and requested ship date
4.How to create an interactive report for displaying plant status to know the status of a particular material
5. How to develope a report on Sales Order displaying Sales order Number, Sales order date, Material, PO Date and Customer requested date
Thanks in advance!!
Uma.
Message was edited by:
        Uma Ravi

Hi Ravi,
for 3, 4, 5 --> u can go through the code ...
REPORT ZEX2 MESSAGE-ID arc NO STANDARD PAGE HEADING.
Tables :kna1,vbak.
SELECT-OPTIONS : so_vkorg FOR vbak-vkorg OBLIGATORY,
                 so_vtweg FOR vbak-vtweg OBLIGATORY,
                 so_spart FOR vbak-spart,
                 so_kunnr FOR kna1-kunnr.
DATA : BEGIN OF sales_open OCCURS 0 ,
       vbeln LIKE vbak-vbeln,
       auart LIKE vbak-auart,
       kunnr LIKE kna1-kunnr,
       bstnk LIKE vbak-bstnk,
       lfstk LIKE vbuk-lfstk,
       fkstk LIKE vbuk-fkstk,
       gbstk LIKE vbuk-gbstk,
       END OF sales_open.
DATA : BEGIN OF itm_sales OCCURS 0,
       vbeln LIKE vbap-vbeln,
       posnr LIKE vbap-posnr,
       matnr LIKE vbap-matnr,
       kwmeng like vbap-kwmeng,
       lfsta LIKE vbup-lfsta,
       lfgsa LIKE vbup-lfgsa,
       fksta LIKE vbup-fksta,
       fksaa LIKE vbup-fksaa,
       gbsta LIKE vbup-gbsta,
       END OF itm_sales.
DATA : l_kunnr LIKE kna1-kunnr,
       l_vkorg LIKE vbak-vkorg,
       l_vtweg LIKE vbak-vtweg,
       l_spart LIKE vbak-spart.
DATA: v_statusl(20) TYPE c,
      v_statusb(20) TYPE c,
      v_statusf(20) TYPE c,
      v_statusg(20) TYPE c,
      v_status(20) TYPE c,
      v_field(1) TYPE c.
data : v_openqty like vbap-kwmeng.
**Selection Screen Validations.
AT SELECTION-SCREEN.
PERFORM validations.
*&      Form Validations
*       text
* --> p1        text
* <-- p2        text
FORM validations.
**Customer
IF NOT so_kunnr[] IS INITIAL.
    SELECT SINGLE kunnr INTO l_kunnr
           FROM kna1
           WHERE kunnr IN so_kunnr.
    IF sy-subrc NE 0.
      MESSAGE e002 WITH text-005.
    ENDIF.
ENDIF.
**Sales Organization
IF NOT so_vkorg[] IS INITIAL.
    SELECT SINGLE vkorg INTO l_vkorg
           FROM tvko
           WHERE vkorg IN so_vkorg.
    IF sy-subrc NE 0.
      MESSAGE e003 WITH text-006.
    ENDIF.
ENDIF.
**Distribution Channel
IF NOT so_vtweg[] IS INITIAL.
    SELECT SINGLE vtweg INTO l_vtweg
            FROM tvkov
            WHERE   vkorg IN so_vkorg
             AND    vtweg IN so_vtweg.
    IF sy-subrc NE 0.
      MESSAGE e004 WITH text-007.
    ENDIF.
ENDIF.
**Division
IF NOT so_spart[] IS INITIAL.
    SELECT SINGLE spart INTO l_spart
            FROM tvta
            WHERE   vkorg IN so_vkorg
            AND     vtweg IN so_vtweg
            AND     spart IN so_spart.
    IF sy-subrc NE 0.
      MESSAGE e005 WITH text-008.
    ENDIF.
ENDIF.
ENDFORM.                    " Validations
Top-of-page.
PERFORM sales_top_of_page.
Start-of-selection.
PERFORM sales_sel.
*&      Form sales_sel
*       text
* --> p1        text
* <-- p2        text
FORM sales_sel.
SELECT vbeln auart kunnr bstnk
     lfstk fkstk gbstk
     INTO TABLE sales_open
     FROM vbakuk
     WHERE vkorg IN so_vkorg
     AND   vtweg IN so_vtweg
     AND   spart IN so_spart
     AND   kunnr IN so_kunnr
     AND gbstk NE 'C'.
LOOP AT sales_open.
    WRITE:/4 sy-vline,
           5 sales_open-vbeln HOTSPOT ON COLOR 2 INTENSIFIED OFF,
           16 sy-vline,
           17 sales_open-auart COLOR 2 INTENSIFIED OFF,
           27 sy-vline,
           28 sales_open-kunnr COLOR 2 INTENSIFIED OFF,
           40 sy-vline,
           41 sales_open-bstnk COLOR 2 INTENSIFIED OFF,
           55 sy-vline,
           56 sales_open-lfstk,
           76 sy-vline,
           77 sales_open-fkstk,
           96 sy-vline,
           97 sales_open-gbstk ,
           117 sy-vline.
    HIDE sales_open-vbeln .
ENDLOOP.
ENDFORM.                    " sales_sel
*&      Form sales_top_of_page
*       text
* --> p1        text
* <-- p2        text
FORM sales_top_of_page.
WRITE:/4 sy-uline(114),
     50 'OPEN SALES ORDERS' COLOR 7 INTENSIFIED ON .
WRITE: /4 sy-vline,
          5 'SalesOrder' COLOR 1 ,
          16 sy-vline,
         17 'OrderType' COLOR 1,
         27 sy-vline,
         28 'Customer' COLOR 1,
         40 sy-vline,
         41 'PoNumber' COLOR 1,
         55 sy-vline,
         56 'Delivery Status' COLOR 1,
         76 sy-vline,
         77 'Billing Status' COLOR 1,
         96 sy-vline,
         97 'Processing Status' COLOR 1,
         117 sy-vline .
WRITE:/4 sy-uline(114).
ENDFORM.                    " sales_top_of_page
AT LINE-SELECTION.
SELECT       a~vbeln
               a~posnr
               a~matnr
               a~kwmeng
               b~lfsta
               b~lfgsa
               b~fksta
               b~fksaa
               b~gbsta
               INTO TABLE itm_sales
               FROM vbap AS a JOIN vbup AS b
               ON a~vbeln EQ b~vbeln
               AND a~posnr EQ b~posnr
               AND b~gbsta NE 'C'
               WHERE a~vbeln EQ sales_open-vbeln.
IF NOT sales_open IS INITIAL.
    LOOP AT itm_sales.
      at end of vbeln .
      sum.
      v_openqty = itm_sales-kwmeng.
      endat.
      WRITE:/5 itm_sales-vbeln,
                itm_sales-posnr,
                itm_sales-matnr,
                itm_sales-kwmeng,
                itm_sales-lfsta,
                itm_sales-lfgsa,
                itm_sales-fksta,
                itm_sales-fksaa,
                itm_sales-gbsta.
    ENDLOOP.
ENDIF.
skip 2.
write:/ 'open Quantity for the order is ', v_openqty .
for 1.
open invoices..
SELECT vbeln
         fkart
         kunag
         gbstk
         INTO TABLE it_billing_h
         FROM vbrkuk
         WHERE vkorg IN so_vkorg
         AND vtweg IN so_vtweg
*        AND spart IN so_spart
         AND kunag IN so_kunnr
        and   year in p_year                  ---->"parameter for year..
         AND gbstk NE 'C'.                   "----> open invoices
for 2..
2. refer TABLES mara, EINA ..
regards,
VIjay

How can I set the parameters of global channels and tasks previously created inside my application?

Hi everyone !
Before proceeding to the description below I think it´s important to say that I´m using NI USB-6008 as DAQ device and the driver used is DAQmx 7.5.
I´m currently developing an application into which I intend to be able to have complete control of the DAQ device being used, i.e, I´ll be able to create, delete and change the configuration of global channels and tasks previously created, among other things.
To achieve the ends specified above I´ve already developed two vis, one to create global channels and the other to create tasks, and these two are doing a fine job. After this, I thought I came to the easy part ... I think I couldn´t be far for the truth! I thought that everything I should do was to specify which channel or task I´d like to configure and then use a property node to get the results I wanted, but it´s not working ...there are some DAQmx property nodes I thought I could use to do it but I didn´t find a way to change the configuration of the global channels, and none of these property nodes seemed to work, i.e, although the simple vis used to test them ran the chosen parameters didn´t alter at all, after each execution I used MAX to see if they had changed, and to my chagrin they hadn´t.
Can anybody lend me a hand with this problem? As always, any help would be deeply appreciated !

Hi Giovani,
There is a developer zone tutorial that discussus some advanced data acquisition features including programmatic saves of NI-DAQmx tasks, global channels, and scales. This tutorial also includes an example program.
I wrote a short program that creates tasks in MAX. Whenever I wanted to change a part of the task, I would just change that feature in the example program. Take a look at the examples and please let me know if you have any further questions.
Regards,
Hal L.
Attachments:
create task example.vi ‏33 KB

What should be done to include the current controlfile in the database copy

Hi
When trying to create a copy of the database it always fails copying the controlfile
What should be done to include the current controlfile in the database copy with the %b format
RMAN> backup as copy database format 'd:\backup\%b'
2> ;
Starting backup at 13-SEP-10
using channel ORA_DISK_1
channel ORA_DISK_1: starting datafile copy
input datafile file number=00001 name=D:\ORACLE\ORADATA\ORCL\SYSTEM01.DBF
output file name=D:\BACKUP\SYSTEM01.DBF tag=TAG20100913T204940 RECID=16 STAMP=729636617
channel ORA_DISK_1: datafile copy complete, elapsed time: 00:00:45
channel ORA_DISK_1: starting datafile copy
input datafile file number=00003 name=D:\ORACLE\ORADATA\ORCL\UNDOTBS01.DBF
output file name=D:\BACKUP\UNDOTBS01.DBF tag=TAG20100913T204940 RECID=17 STAMP=729636660
channel ORA_DISK_1: datafile copy complete, elapsed time: 00:00:35
channel ORA_DISK_1: starting datafile copy
input datafile file number=00002 name=D:\ORACLE\ORADATA\ORCL\SYSAUX01.DBF
output file name=D:\BACKUP\SYSAUX01.DBF tag=TAG20100913T204940 RECID=18 STAMP=729636692
channel ORA_DISK_1: datafile copy complete, elapsed time: 00:00:35
channel ORA_DISK_1: starting datafile copy
*copying current *control file**
RMAN-03009: failure of backup command on ORA_DISK_1 channel at 09/13/2010 20:51:36
ORA-19715: invalid format b for generated name
ORA-27302: failure occurred at: slgpn
continuing other job steps, job failed will not be re-run
channel ORA_DISK_1: starting datafile copy
input datafile file number=00004 name=D:\ORACLE\ORADATA\ORCL\USERS01.DBF
output file name=D:\BACKUP\USERS01.DBF tag=TAG20100913T204940 RECID=19 STAMP=729636697
channel ORA_DISK_1: datafile copy complete, elapsed time: 00:00:01
channel ORA_DISK_1: starting full datafile backup set
channel ORA_DISK_1: specifying datafile(s) in backup set
*including current SPFILE in backup set*
channel ORA_DISK_1: starting piece 1 at 13-SEP-10
RMAN-00571: ===========================================================
RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
RMAN-00571: ===========================================================
RMAN-03009: failure of backup command on ORA_DISK_1 channel at 09/13/2010 20:51:38
ORA-19715: invalid format b for generated name
ORA-27302: failure occurred at: slgpnEdited by: hrishy on Sep 13, 2010 8:26 AM

hrishy wrote:
Allright your trick configure controlfile autobackup on does the trick but i am cluless why it worksWhy clueless? That's a documented and a perfectly normal behavior!
http://download.oracle.com/docs/cd/E11882_01/backup.112/e10642/rcmconfb.htm#BRADV89408
HTH
Aman....

Search Query that shows articles based on the current logged in users Office location

Hi,
I've set up a "news" channel that shows articles targeted to the current user. Basicly this on done by queryting the property of the custom "Office Location" termset.
My setup is something like the following in my term store:
The setup works perfect now. countries are not taggable so at the moment the user needs to choose City 1.. City 2 etc. for their articles which works fine since sometimes articles are also only targeted to cities and not countries.
Anyways now we have got 2 users in City 4. Here it makes no sense that articles should be targeted City 3 and City 4 in order to show articles to entire Country 2. Basicle what I want here is that if an article is targeted with City 3 it should also be shown
to City 4 users.
How is this archived best? I have tried to make the Countries available for tagging as well, however it not show anything since the user property of course still is City 3 or City 4.
Thanks for your time

Hi,
You can not get hold of the parent in your scenario. You want the parent of the tagged term in the user profile, and there is no built-in mechanism in search to get this. So as I mentioned you have to use JSOM to get the parent term, and then use that in
your owstaxIdOfficex0020Location:term query.
owstaxIdOfficex0020Location:{User.SPS-Location.IDWithChildren}
would be a valid query, except it won't help you much :)
Thanks,
Mikael Svenson - Search Enthusiast
SharePoint MVP/MCT/MCPD - If you find an answer useful, please up-vote it.
http://techmikael.blogspot.com/
Author of Working with FAST Search Server 2010 for SharePoint

Set-IRMConfiguration failed with error "Cou ld not establish trust relationship for the SSL/TLS secure channel."

Hi, experts
I'm trying to configure a lab environment according tutorial http://www.msexchange.org/articles-tutorials/exchange-server-2010/compliance-policies-archiving/rights-management-server-exchange-2010-part3.html
After completing configuration, I execute cmdlet Set-IRMConfiguration -InternalLicensingEnabled $true, but get error
The remote certificate is invalid according to the validation procedure. ---> The underlying connection was closed: Cou
ld not establish trust relationship for the SSL/TLS secure channel. ---> Failed to get Server Info from https://exhv-65
94/_wmcs/certification/server.asmx.
+ CategoryInfo : InvalidOperation: (:) [Set-IRMConfiguration], Exception
+ FullyQualifiedErrorId : C810E449,Microsoft.Exchange.Management.RightsManagement.SetIRMConfiguration
Then I run cmdlet Test-IRMConfiguration -Sender [email protected] and get error
Results : Checking Exchange Server ...
- PASS: Exchange Server is running in Enterprise.
Loading IRM configuration ...
- PASS: IRM configuration loaded successfully.
Retrieving RMS Certification Uri ...
- PASS: RMS Certification Uri: https://server1/_wmcs/certification.
Verifying RMS version for https://server1/_wmcs/certification ...
- WARNING: Failed to verify RMS version. IRM features require AD RMS on Windows Server 2008 SP2 with the
hotfixes specified in Knowledge Base article 973247 (http://go.microsoft.com/fwlink/?linkid=3052&kbid=973247)
or AD RMS on Windows Server 2008 R2.
Microsoft.Exchange.Security.RightsManagement.RightsManagementException: Failed to get Server Info from https:
//server1/_wmcs/certification/server.asmx. ---> System.Net.WebException: The underlying connection was clos
ed: Could not establish trust relationship for the SSL/TLS secure channel. ---> System.Security.Authenticatio
n.AuthenticationException: The remote certificate is invalid according to the validation procedure.
at System.Net.Security.SslState.StartSendAuthResetSignal(ProtocolToken message, AsyncProtocolRequest async
Request, Exception exception)
at System.Net.Security.SslState.ProcessReceivedBlob(Byte[] buffer, Int32 count, AsyncProtocolRequest async
Request)
at System.Net.Security.SslState.StartReceiveBlob(Byte[] buffer, AsyncProtocolRequest asyncRequest)
at System.Net.Security.SslState.ProcessReceivedBlob(Byte[] buffer, Int32 count, AsyncProtocolRequest async
Request)
at System.Net.Security.SslState.StartReceiveBlob(Byte[] buffer, AsyncProtocolRequest asyncRequest)
at System.Net.Security.SslState.ProcessReceivedBlob(Byte[] buffer, Int32 count, AsyncProtocolRequest async
Request)
at System.Net.Security.SslState.StartReceiveBlob(Byte[] buffer, AsyncProtocolRequest asyncRequest)
at System.Net.Security.SslState.ForceAuthentication(Boolean receiveFirst, Byte[] buffer, AsyncProtocolRequ
est asyncRequest)
at System.Net.Security.SslState.ProcessAuthentication(LazyAsyncResult lazyResult)
at System.Threading.ExecutionContext.Run(ExecutionContext executionContext, ContextCallback callback, Obje
ct state)
at System.Net.TlsStream.ProcessAuthentication(LazyAsyncResult result)
at System.Net.TlsStream.Write(Byte[] buffer, Int32 offset, Int32 size)
at System.Net.PooledStream.Write(Byte[] buffer, Int32 offset, Int32 size)
at System.Net.ConnectStream.WriteHeaders(Boolean async)
--- End of inner exception stack trace ---
at System.Web.Services.Protocols.WebClientProtocol.GetWebResponse(WebRequest request)
at System.Web.Services.Protocols.HttpWebClientProtocol.GetWebResponse(WebRequest request)
at System.Web.Services.Protocols.SoapHttpClientProtocol.Invoke(String methodName, Object[] parameters)
at Microsoft.Exchange.Security.RightsManagement.SOAP.Server.ServerWS.GetServerInfo(ServerInfoRequest[] req
uests)
at Microsoft.Exchange.Security.RightsManagement.ServerWSManager.ValidateServiceVersion(String featureXPath
--- End of inner exception stack trace ---
at Microsoft.Exchange.Security.RightsManagement.ServerWSManager.ValidateServiceVersion(String featureXPath
at Microsoft.Exchange.Management.RightsManagement.IRMConfigurationValidator.ValidateRmsVersion(Uri uri, Se
rviceType serviceType)
at Microsoft.Exchange.Management.RightsManagement.IRMConfigurationValidator.TryGetRacAndClc()
OVERALL RESULT: PASS with warnings on disabled features
From the error message, this issue seem to related with SSL/TLS connection. So I go back to check configuration and find out a difference to tutorial. Current SCP url is https://server1/_wmcs/certification, but in tutorial it is https://server1:433/_wmcs/certification.
On my opinion, I don't think it is the real reason.
So, how can I resolve this error? Could you give me some suggestion? Thanks in advance.
System Info:
Windows Server 2008 R2 + Exchange Server 2010 SP3 RTM

Hi
Please have a try with the solution on this KB article
“Error message when you try to test access from the Microsoft Dynamics CRM E-mail Router: "Incoming Status: Failure - The underlying connection was closed: Could not establish trust relationship for the SSL/TLS secure channel"”
http://support.microsoft.com/kb/954584/en-us
Cheers
Zi Feng
TechNet Community Support

"Could not establish trust relationship for the SSL/TLS secure channel"

During the configuration of DUET_E , when calling the DUET Application from SharePoint, the following error is shown :
"Could not establish trust relationship for the SSL/TLS secure channel with authority 'MYSAPNW702SERVER:8001'"
I have already seen the Post :
Error in DUET Configuration at SSL
This mentions the error, but does not provide any answers on resolution.
The DUET_E troublshooting guide suggests that the SAP Standard SSL Certificate is added to SharePoint Central Admin > Security > Manage Trusts
This has also been done.
We are using the Standard SAP SSL Self signed certificate - not one signed by an external CA.
Can anyone provide any guidance ?
Thanks in advance.

Hi Min,
reading through your first post the problem might be the CN of the certificate. If you used the Wizard or the default way to create a self signed certicate, it is probably created with the CN server.domain (the fully qualified name of the server).
However, when you created the BDC models the URLs pointing to the WSDL is probably only the servername (at least that is what I would assume after seeing your error message).
Because of that SharePoint calls the SAP Duet server with the severname, but the certificate presented by the SAP system is not the servername, but the fully qualified servername. Because of that -- although SharePoint trusts the certificate -- the URL and certificate do not match and you get the error "Could not establish trust relationship for the SSL/TLS secure channel with authority 'MYSAPNW702SERVER:8001"
If that is the case you have two options:
1) you go to STRUST and create a new SSL certificate that has a CN of only the servername. Then you export this certificate and trust it in SharePoint
2) or -- and this is the way I would recommend -- you try to adjust the URL used in the BDC model. Usually you get only the servername (and not the fully qualified DNS name) when you have not specified the profile parameter icm/host_name_full. Which URL is currently used when you start transaction SAML2 or SOAMANAGER? If you have not yet set icm/host_name_full, then give this a try.
Regards,
Holger.

Could not establish trust relationship for the SSL/TLS secure channel with authority

Hello everyone, I need to establish a connection between my HTTPS WCF hosted in Windows Azure Web Role and my Windows Store App Client. The service is actually exposed for testing purposes using a self-signed certificate.
I have installed the certificate in Personal and Trusted Root Certification Authorities in Current User and Local Manchine.
In the Windows Store App, I create the service reference pointing to the cloud https service, then edit the manifest and create a new declaration to Add a New Certificate, I checked Exclusive Trust and Auto select, pointing to Root storage name and
my self-signed certificate.cer.
The result is the following exception in the IntelliTrace stack:
Exception:Caught: "The remote certificate is invalid according to the validation procedure." (System.Security.Authentication.AuthenticationException)
A System.Security.Authentication.AuthenticationException was caught: "The remote certificate is invalid according to the validation procedure."
Time: 19/01/2015 04:42:33 p. m.
Thread:Worker Thread[17080]
Exception:Thrown: "Could not establish trust relationship for the SSL/TLS secure channel with authority 'appchallengewhi.cloudapp.net'." (System.ServiceModel.Security.SecurityNegotiationException)
A System.ServiceModel.Security.SecurityNegotiationException was thrown: "Could not establish trust relationship for the SSL/TLS secure channel with authority 'appchallengewhi.cloudapp.net'."
Time: 19/01/2015 04:42:34 p. m.
Thread:Worker Thread[17080]
Appreciate any help, to solve this with the approach of WCF Service Reference in Windows Store App.
Note:
If I call the HTTPS service using a Console App it works very good using the following the code:
ChannelFactory<IAgentService> factory = new ChannelFactory<IAgentService>("basicHttpBinding_IAgentService");
ServicePointManager.ServerCertificateValidationCallback = (sender, cert, chain, error) => true;
IAgentService wcfProxy = factory.CreateChannel();
Thanks in advance,
RC

Maybe not implemented.
https://social.msdn.microsoft.com/Forums/windowsapps/en-US/2dab2818-8f4c-4474-a7a1-db2cbfb40d40/accepting-client-certificate-for-https-connections?forum=winappswithcsharp

Problem with the right and left Channel

Hey Guys,
i bought a few days ago the X-Fi Titanium PCIe Card. Now my problem:?
After i installed the drivers i noticed that i can hear the sounds of the left speaker also in the right speaker of my Headphone (Sennheiser PC60). I made a channel test and here the same. The guy sais "Left Channel" and i hear it on both speakers. The same with the right channel.
I made a clean restart and uninstalled all Drivers and Applications and reinstalled them: -> Same problem
I made a clean Windows installation (Vista x64): -> Same problem
i tried the Daniel_K-Driver: -> Same problem
Have someone an idea to solve that problem?
greets
kybo

When Soundbooth was first developed, it had a few extra things than what were not available in Audition. However, Audition remained the more high end sound editing tool. Soundbooth was locked to a multiple channel editing approach. In Audition, single editing is easy - you simply click the L or R at the right end of the sound channel to lock it and then you can edit the other channel only.
Soundbooth has been discontinued and Audition now has taken its place from CS6 to the Creative Cloud.
The above is some background info. To your current situation, you can use a workaround like:
* Export your audio file to separate channels by File > Export > Channels to mono files.
You will get 2 files with _L and _R suffix.
You can then edit them separately. You can go from Mono to Stereo by the following step.
Or
* Choose - Edit > Insert > Channels into New Multitrack file.
That will separate the Left and Right Channels and add them to a new multitrack file.
You can then click the Edit link at the top right of the channel to edit it.
You can then save that file as a new audio file.
Dean

HT5958 Audio prevents relinking to original media -- can I manually change the number of audio channels for a video clip?

I recently updated to Final Cut X 10.1. I had a project for which I was heavily editing the audio, so I was using the "detach audio" feature and in some cases deleting the audio track. Now, when I try to go into the timeline and relink the movie files (which weren't linked automatically after update), the original media won't relink because "the original file didn't have audio, but the new file does."
Is there anyway to edit the misreferenced file so it beleives it has an audio track?
Thank you for any and all suggestions. I really don't want to start this edit over from scratch.
Ben

Thanks for the responses, guys. I guess I wasn't really all that clear. Something to do with FCP 6 and the Kona III card is telling FCP to set up each project with 16 channels of audio - and ONLY 16 channels of audio. Anywhere that there is a drop-down or check box, the drop-down or check box is either grayed out or only provides choices centered around 16 channels of audio. So, for example, let's say I go to the "Capture Presets" tab under "Audio/Video Settings" and click on "Edit" to modify the current preset. Under "QuickTime Audio Settings," I select "AJA Kona" as my device. Then, under the "Format" drop-down, I have four possible audio formats to choose from - ALL of them showing 16 channels (e.g. - "48.000 khz 24-bit 16-channel"). Nowhere is there an option of selecting, say "48.000 khz 24-bit 2-channel." Everything under every tab specifies 16-channel. So, as a result, I can't tell it to disable the fourteen tracks that I'll NEVER use. I even tried starting with the "Generic" settings tab, used to create your own presets, and even that would ONLY allow me 16-channels - and I couldn't over-ride it!
So far, the only way I've found to work around this is to manually go in and turn off the little green nodes indicating which audio track(s) you don't want to capture. The problem is, every time I have to do this, I'm manually turning of FOURTEEN audio channels.
Hope this helps clarify...
Tim Walton
KVIE Public Television

How do I share / unlink the right and left channel, so I can work with them individually ?

I use "Adobe Sound Booster CS5"
I have a stereo soundtrack, which I only want to remove noise in only one channel (right).
How do I share / unlink the right and left channel, so I can work with them individually ?

When Soundbooth was first developed, it had a few extra things than what were not available in Audition. However, Audition remained the more high end sound editing tool. Soundbooth was locked to a multiple channel editing approach. In Audition, single editing is easy - you simply click the L or R at the right end of the sound channel to lock it and then you can edit the other channel only.
Soundbooth has been discontinued and Audition now has taken its place from CS6 to the Creative Cloud.
The above is some background info. To your current situation, you can use a workaround like:
* Export your audio file to separate channels by File > Export > Channels to mono files.
You will get 2 files with _L and _R suffix.
You can then edit them separately. You can go from Mono to Stereo by the following step.
Or
* Choose - Edit > Insert > Channels into New Multitrack file.
That will separate the Left and Right Channels and add them to a new multitrack file.
You can then click the Edit link at the top right of the channel to edit it.
You can then save that file as a new audio file.
Dean

How Do I Link To The Current Date/Month In iCal?

I have a link on my website which points to a published iCal calendar. The link remains static, for instance, I created the link in January, and it pointed to the January view of the calendar.
Now that its February, I'd like the link to point to the February month view (and so on throughout the year), but it remains linked to January.
How do I make the link dynamic so that it points to the current month/date? Thanks in advance.
G5 Dual 2.0 Mac OS X (10.4.4)

JFKrohn, Welcome to the discussion area!
To get the current month, use a link like this:
http://ical.mac.com/WebObjects/iCal.woa/wa/default?u=UserName&v=1&n=CalendarName.ics
Where
UserName = .Mac user name
CalendarName = name of published calendar

How to load a class dynamically in the current/system class loader

I need to dynamically load a new jdbc driver jar to the current/system class loader... Please note that creating a new classloader will not help since the DriverManager refers to the systemclassloader itself.
Restarting the application by appending the jar to its classpath will solve the problem but I want to avoid doing this.

Did you then create a ClassLoader to load the JDBC
driver and then install it into the system as
directed by the JDBC specification (ie
Class.forName(someClassName))?
And then try to use it from a class loaded fromsome
other ClassLoader (i.e. the system class loader)?
If you did not try this please explain why not.O.K. I just looked at the source to
java.sql.DriverManager. I did not know what I was
talking about, as what I suggested above will not
work.
This is my new Idea:
Create a URLClassLoader to load the JDBC driver also
in this ClassLoader you need to place a helper class
that does the following:
public class Helper {
public Driver getJDBCDriver(String driverClassName,
String url) {
try {
Class.forName(driverClassName);
Driver d = DriverManager.getDriver(url);
return d;
catch(Exception ex) {
ex.printStackTrace();
return null;
}Now create an instance of the Helper class in the new
ClassLoader, and call its getJDBCDriver method to get
an instance of the driver (you will probably have to
create an interface in the root class loader that the
Helper implements so that you can easily call it).
Now from the root classloader you can make calls
directly to the returned Driver and bypass the
DriverManager and its restrictions on cross
ClassLoader access.
The only catch here is that you would have to call to
the returned Driver directly and not use the Driver
Manager.This sounds like will work but I did not want to load DriverManager in a new classloader.. I did a hack
I unzip the jar dynamically in a previously known location (which I included in my classpath when launching the app). The classLoader finds the class now though it did not exist when the app was launched !
A hack of-course but works eh ..

The current i/o channels

Similar Messages

Maybe you are looking for