Understand and configure CBQoS.-

Hi again, i'm trying configure CBQoS for monitoring QoS (jitter, delay and packet loss). And use PRTG to see it.
I'm frustrated with this CBQoS and IP SLA.
I have many 2960 (version15.0(2)SE5)
I try this:
http://www.cisco.com/c/en/us/td/docs/ios/12_4t/12_4t4/ht_cbqos.html
but didn't work.
Some one please can share some doc to undestand and configure CBQOS (i can't found anything else from Cisco)
Thanks for help.
PS:I try also IP SLA but i can't download IP services IOS for C3560 to use as source.

I realy sorry, i didn't realise for the IOS version. I'm replying myself:
Upgrade IOS:
c2960-lanbasek9-mz.122-55.SE8
to
c2960-lanbasek9-mz.150-2.SE4
Switch(config)#snmp mib ?
community-map     Community Mapping as per RFC-2576
notification-log Configure the Notification Log MIB
persist           Persistence for MIBS
target            target extention CLI from SNMP
Now, i wiil try to get work CBQoS.
Thanks

Similar Messages

Configure CBQoS for monitoring.

Hi, i want to configure CBQoS in a lot of 2960 switches (with snmp v1) for monitoring: jitter, delay and packets lost with PRTG software.
I not found documentation for understand CBQoS, but i see this doc:
http://www.cisco.com/en/US/docs/ios/ios_xe/qos/configuration/guide/cbqos_mib_xe.html
and when i put these commands:
1. enable
2. configure terminal
3. snmp-server ifindex persist
4. snmp mib persist [cbqos | v3mibs]
5. end
6. write mib-data
I can't do the step 4
Switch(config)#snmp mib ?
community-map     Community Mapping as per RFC-2576
notification-log Configure the Notification Log MIB
rep               Enable SNMP Resilient Ethernet Protocol options
target            target extention CLI from SNMP
PS: Or maybe is a simplest way to monitor QoS.
Thanks!

I realy sorry, i didn't realise for the IOS version. I'm replying myself:
Upgrade IOS:
c2960-lanbasek9-mz.122-55.SE8
to
c2960-lanbasek9-mz.150-2.SE4
Switch(config)#snmp mib ?
community-map     Community Mapping as per RFC-2576
notification-log Configure the Notification Log MIB
persist           Persistence for MIBS
target            target extention CLI from SNMP
Now, i wiil try to get work CBQoS.
Thanks

EIS Installation and Configuration

Hi Everybody,
I am trying to install EIS 9.31 on my laptop (i.e Win2k3 Server), I have successfully installed Essbase and EIS
But I have no idea how to configure(Creating DSN Catalog) in EIS.
I am using Oracle 10g. Can any one please help me on thsi installation.
Already I gone through the installation document but I didn't understand how to configure.
If anyone having installation and Configuring Screen shots please send me to my mail
Mail Id: [email protected]
This is very urgent I need to give presentation on the EIS
Thanks in Advance for your help
Awaiting for your quick Response

I'm not sure what version of software you are looking to install, but for 9.3.1, we just installed our application server (Weblogic), installed Shared Services, supplied the database info and we were good to go. I do believe; however, your mileage will vary depending on the application server you use as some of them have an option for 'automatic' installation and some are manual. (I went the 'automatic' route) You will need to refer to the installation documentation for all of the relevant details, though.

Hi, i have tryed to install os x leopard, (its a old imac) , disk utility is greyed out , my install dvd cant find any hdd to install on , my only way to format and configure is through terminal but dont know what commands to execute

hi, i have tryed to install os x leopard, (its a old imac) , disk utility is greyed out , my install dvd cant find any hdd to install on , my only way to format and configure is through terminal but dont know what commands to execute...
i tryed diffrent commands such as diskutil eraseDisk JHFS+ Disk1
diskutil list , wont show up my harddrive , i now its functionally cause it shows up in disk utility with name and i can get info about it , but everything is greyed out can only switch between "erase , partition , recover , Raid ,....
when i click the apple in the top left corner the whole menu is greyed out... what to do ? help me please
Sincerly AppleNoob92
p.s i have no experience in apple imac's at all never used before, but im kinda windows nerd so computers i understand but this imac make my insane, cant seem to find any solutions anywhere on the WWW....

Your HD may be crashed, so you probably should use the oringinal install discs to run Apple Hardware Test in extended mode. If error codes appear this confirms a hardware failure. In addition you cannnot repair the HD using Disk Utility from the startup disk, you have to use the origninal Install discs that shipped with the computer or the most up-to-date version of OS X on a disc that you have.

How to install and Configure sharepoint foundation on administrator account ??

Hi there guys dev
I want to try sharepoint foundation for first time .
I installed windows server 2012 ans sql server 2012 and then installed sharepoint foundation 2013 .
now when I want to create a new server farm enter my windows name as database name and then enter my administrator account name as username ans it's passwors as password but after then when I click on next to create new server farm give this error :
"the administrator account can't use for new server "
please help how can I create a new server farm with administrator account .
I don't want to create it with the active directory domain and add new forest and create it with my domain name ?
if does it a way to create a new server farm with administrator account so please help to create it ?
thanks dear
Great Regards :
Raha
whit the best regard : Raha

Hi Raha,
According to your description, my understanding is that you got an error when you created a new farm with the administrator account by runnning configuration wizard.
Is the SQL Server installed in the server that hosted SharePoint 2013 Foudation? If not, please make sure the server hosted SQL Server has the same account with the server hosted SharePoint 2013 Foudation.
Please run the SharePoint 2013 Products Configuration wizard with ‘Run as administrator’.When you entered the user’s name, please use the format ‘domain\user_name’.
In addition, please check the log file to find more information about this issue. The path is : C:\Program Files\Common Files\microsoft shared\Web Server Extensions\15\LOGS.
Also , you can use Event Viewer to find the log by Start->Run->event viewer.
Here is an article for installing and configuring SharePoint 2013, please take a look at:
http://sharepointv15.wordpress.com/2012/07/19/installing-sharepoint-2013-preview/
I hope this helps.
Thanks,
Wendy
Wendy Li
TechNet Community Support

SSRS - Installation and configuration

Hi ,
Am new to SQL Server and I need to setup SQL Server Repoting services on SQL server cluster where instance is already running.
Version : SQL Server 2008 SP1
I did some research online and found some links and videos on how to do it. My understanding is that I need to Install Reporting services and configure it. This is needed for Sharepoint. Here are the links which am planning to use.
http://technet.microsoft.com/en-us/library/ms143736(v=sql.105).aspx
http://technet.microsoft.com/en-us/library/cc281311(v=sql.105).aspx
http://technet.microsoft.com/en-us/library/bb326356(v=sql.105).aspx
http://msdn.microsoft.com/en-us/library/ms144292(v=sql.105).aspx
I got some doubts when going through the above links.
1) Which mode should I choose while installing it Native or Sharepoint integrated mode, am thinkning as we have sharepoint enviornment, I need to choose Sharepoint Integrated mode, please confirm.
2) Is downtime needed to do this. I mean I can install it when the instance is up and running right ?
3) As it's a clustered environment, I'm thinking I need to install SSRS on one server but what changes should I make on the second server to recognize this?
4) Can you please share me any more better links to do this on clustered enviornment, which has step-by-step procedure.
Thanks in advance

Hello,
1. It based on your requirement, if you want to use the features of SharePoint, you can configure the Reporting Services in SharePoint Integrated mode. Report server modes are mutually exclusive, you can switch a report server from one mode to the other.
2.No. SQL Server Reporting Services is independent SQL Server component which you can installed side by side with SQL Server instance.
3.Report Server service cannot participate in a failover cluster, you can install Reporting Services on a computer that has a SQL Server failover cluster installed and host the report server database on a SQL Server failover cluster. The report server runs
independently of the failover cluster.
Reference:Host a Report Server Database in a SQL Server Failover Cluster
4. The following threads are about similar requirement,please refer to:
http://social.msdn.microsoft.com/forums/sqlserver/en-US/b9db5c98-1b36-47a4-927d-c03e536f7cb7/reporting-services-on-failover-cluster-nodes
http://www.sqlservercentral.com/Forums/Topic849220-146-1.aspx
Regards,
Fanny Liu
Fanny Liu
TechNet Community Support

Install and configure Hyper V for VDI

Hi Everyone
I am trying to setup a POC lab using Hyper-V to demonstrate use case for VDI
I do understand you need to have 2012R2 connection brokers and RDSH servers as part of the VDI deployment.
Coming from a vmware background I have much to learn in this area. I have 4 HS22 blades installed with 2012R2 Datacentre and configured teaming for the management Network. All 4 2012R2 host presented with shared storage from our SAN. On each host there are
6 NIC . 2 is for management / migration ?? and the rest of the 4 Nic is for the VM data network
On the management Teaming Nic, I have setup 2 NIC in independent mode with load balancing Dynamic. The second nic is set as Standby Adapter.
Before I enable the Hyper V role , I would like to find out the best practice for setting up 2012R2 HyperV for VDI ? Do I need a seprate migration network or use the same management teaming Nic ? And Where do use specify in hyper to use this network for
vm migration between host.
In Vsphere we use port group to assign different Vlan for each VMs. You can have multiple Port groups (with vlan id) belongs to a vsphere distributed V switch. Host can be part of the distribute vswitch.
My understanding you have to manually enter the vlan id on each separate vm, there is no drop box to choose the vlan
is there any way we can achieve the similar result in Hyper V.
we do have license to use VMM
Many thanks

Here's an example of how I set up my networking for VDI using 2 hosts and a 10Gb connection. This configuration creates the team, the virtual switch with bandwidth mode, adds the different logical networks, sets the VLANs, and assigns the bandwidth
priority for each. You dont see a VLAN associated with the VM Traffic adapter because the switch ports include the VM Traffic Native VLAN for that network.
This is a fairly common setup for sharing the different networks over a 10GB pipe. Also, you don't see our storage network in there due to the way our FCoE is configured. Our FCoE configuration is a separate 10GB connection that uses the switch
to prioritize the bandwidth.
PS C:\Users\Administrator> New-NetLbfoTeam -name ClusterTeam -TeamMembers "Ethernet 2","Ethernet 6","Ethernet 8","Ethernet 9"
PS C:\Users\Administrator> New-VMSwitch "ClusterSwitch" -MinimumBandwidthMode weight -NetAdapterName "ClusterTeam" -AllowManagementOS 0
PS C:\Users\Administrator> Set-VMSwitch "ClusterSwitch" -DefaultFlowMinimumBandwidthWeight 20
PS C:\Users\Administrator> Add-VMNetworkAdapter -ManagementOS -name "VM Traffic" -SwitchName "ClusterSwitch"
PS C:\Users\Administrator> Add-VMNetworkAdapter -ManagementOS -name "Management" -SwitchName "ClusterSwitch"
PS C:\Users\Administrator> Add-VMNetworkAdapter -ManagementOS -name "Live Migration" -SwitchName "ClusterSwitch"
PS C:\Users\Administrator> Add-VMNetworkAdapter -ManagementOS -name "Cluster" -SwitchName "ClusterSwitch"
PS C:\Users\Administrator> Set-VMNetworkAdapterVlan -ManagementOS -VMNetworkAdapterName "Management" -Access -VlanId 153
PS C:\Users\Administrator> Set-VMNetworkAdapterVlan -ManagementOS -VMNetworkAdapterName "Live Migration" -Access -VlanId 13
PS C:\Users\Administrator> Set-VMNetworkAdapterVlan -ManagementOS -VMNetworkAdapterName "Cluster" -Access -VlanId 12
PS C:\Users\Administrator>
PS C:\Users\Administrator>
PS C:\Users\Administrator> Set-VMNetworkAdapter -ManagementOS -name "VM Traffic" -MinimumBandwidthWeight 40
PS C:\Users\Administrator> Set-VMNetworkAdapter -ManagementOS -name "Management" -MinimumBandwidthWeight 20
PS C:\Users\Administrator> Set-VMNetworkAdapter -ManagementOS -name "Live Migration" -MinimumBandwidthWeight 20
PS C:\Users\Administrator> Set-VMNetworkAdapter -ManagementOS -name "Cluster" -MinimumBandwidthWeight 20

EAS Startup issue after OEPM 11 Installation and Configuration

Hi All,
EAS server is not starting up after the successfull installation and configuration of OEPM 11.1.1.2
Provider Services and Shared Services started fine and i was able to login to Shared Services console
During eas startup individually from the startup script i see this catalina.out file with some errors..
By this i understand that there is some problem in selecting the required JRE as i see both JRE and JRE-64 under the
common folder. Anybody has come across this issue while startup of EAS 11.1.1.2
Any help would be accepted...
execve(): No such file or directory
Error trying to exec $HYPERION_HOME/common/JRE/Sun/1.5.0/bin/sparcv9/java.
Check if file exists and permissions are set correctly.
Failed to start a 64-bit JVM process from a 32-bit JVM.
Verify all necessary J2SE components have been installed.
(Solaris SPARC 64-bit components must be installed after 32-bit components.)
execve(): No such file or directory
Error trying to exec $HYPERION_HOME/common/JRE/Sun/1.5.0/bin/sparcv9/java.
Check if file exists and permissions are set correctly.
Failed to start a 64-bit JVM process from a 32-bit JVM.
Verify all necessary J2SE components have been installed.
(Solaris SPARC 64-bit components must be installed after 32-bit components.)
execve(): No such file or directory
Error trying to exec $HYPERION_HOME/common/JRE/Sun/1.5.0/bin/sparcv9/java.
Check if file exists and permissions are set correctly.
Failed to start a 64-bit JVM process from a 32-bit JVM.
Verify all necessary J2SE components have been installed.
(Solaris SPARC 64-bit components must be installed after 32-bit components.)
execve(): No such file or directory
Error trying to exec $HYPERION_HOME/common/JRE/Sun/1.5.0/bin/sparcv9/java.
Check if file exists and permissions are set correctly.
Failed to start a 64-bit JVM process from a 32-bit JVM.
Verify all necessary J2SE components have been installed.
(Solaris SPARC 64-bit components must be installed after 32-bit components.)
Thanks,

Hi,
1. I assume your system is 64 bit.
2. I think you are installing the 64 bit application. In that case you would get both the folders i.e JRE and JRE-64.
3. Seconldy, I would like to set the permissions of the folders to everyone and give full control and test again. ( to do this, right cick ->security ->add 'everyone' -> give him full control and test).
Sandeep Reddy Enti
HCC
http://hyperionconsultancy.com/

How to install and configure OIM with 11i Oracle Applications(11.5.10.2)

Hi,
We are currently having Oracle Applications 11i (11.5.10.2) Instance.
I need to install Identity Management (OIM), SSO and configure these to 11i instance.
Can you please provide me below,
- What are the documents to be followed.
- What are the pre-requisites to install OIM, SSO.
- Where can i get the software of OIM, SSO and any pre-reqs.
- What are the latest versions to be install to support 11i.
Thanks in advance.
Regards,
Kishore K.

What is the last Oracle support date of 11i (Oracle Applications 11.5.10.2) ? I mean no new patch for bug fixing, no Oracle Expert answering Customers' Questions via Metalink.
I understand that to use Extended Support of Oracle Applications 11.5.10.2, we need to pay additional fee. What are the fees? Are we free upgrading to Oracle Applications 12g and Database 11g at anytime? Any constraints? I believe you got an answer in your other thread -- what is the Lifetime of Extended Support of Oracle E-Business Suite Release
For the fees, no one can tell except your Oracle Sales representative.
If we want to upgrade to Applications 12, Database 11G from Oracle Applications 11.5.10.2 and Database 10.2.0.3, what are the hardware requirements and software requirements? Check the installation manual (which I believe you can find by yourself) and old threads for similar discussion -- http://forums.oracle.com/forums/search.jspa?threadID=&q=Hardware+AND+Requirements&objID=c3&dateRange=last90days&userID=&numResults=15&rankBy=10001
How long will it take Oracle to ship Software to us? Usually 3-5 business days.
Atif, please read the links/docs before posting similar questions, posting questions (which we already discussed many times in the forum before) across the forums is just a waste of your and our time.
Thanks,
Hussein

How to install and configure visual composer

hai experts,
any one help me to install and configure the visual composer. and also tell me the procedure for installation and configuration.plz help me.
regards,
puagzh.

Hi raj,
Installing Visual Composer.
Enterprise Portal 6.0
EP 6.0 SP2 (on Web AS 6.20): patch4 or higher
EP 6.0 on Web AS 6.40: SP Stack 05
Add-ons (integrated in EP 6.0 SP2 Patch 5 and higher and in EP 6.0 on Web AS 6.40 SP Stack 05 and higher)
2 Portal Add-ons for design time portal
2 Portal Add-ons for BI Kit (only in EP 6.0 on Web AS 6.40 SP Stack 05)
Runtime Add-on for run time portal
For VC BI Kit: Deploy BI UDI SP Stack 05 to the J2EE Engine of the Portal
Visual Composer Server (can be on same server as portal)
Windows 2000 Server
MS SQL Server 2000 SP3 as Data Persistence
MS IIS 5.0
Microsoft XML Parser 4.0
Visual Composer Client (design time)
Microsoft Internet Explorer 6.0 SP1 or higher
Microsoft XML Parser 4.0
Adobe SVG Viewer 3.0
Visual Composer Client (run time)
Content created by VC 6.0 runs on any clients supported by portal version it is running on (see PAM for Details)
The SAP NetWeaver Visual Composer for the EP 6.0 is installed in two steps:
SAP NetWeaver Visual Composer Storyboard Install for SAP EP 6.0
SAP NetWeaver Visual Composer Add-ons for SAP EP 6.0
Install the story Board
Assign IIS virtual Directories
You can install addins
The SAP NetWeaver Visual Composer Add-on for SAP EP 6.0 is installed on the Portal Server.
Main activities performed during the install are:
Installing a rar file (Resource Adaptor Archive) using EISConnector (Enterprise Information System Connector) in SAP J2EE
Installing a NetWeaver kit for SAP EP 6.0
Open the browser with the following url
http://<machine_name>.<domain>:<port>/VCServer
For more information How to eork check these links.
What is Visual Composer? User Guide
http://help.sap.com/saphelp_nw04/helpdata/en/01/4b7e40417c6d1de10000000a1550b0/frameset.htm
SAP NetWeaver Visual Composer - How to Guides
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/16244247-0a01-0010-3294-d81c21e7e86e
Creating Applications Using SAP NetWeaver Visual Composer
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/2456bf8a-0a01-0010-709a-ffc91ade9f42
How to Model Portal Content Using SAP Visual Composer No Programming Required!
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/ff65b5a2-0a01-0010-5b97-e747192a1d49
Troubleshooting VC:
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/8ee70a47-0a01-0010-d198-f94c2d7d320c
VC e-Learning:
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/5a35194b-0a01-0010-7598-a4bb10e0c5c9
For installation, u have to download from service market place only.
Check this thread,
Visual Composer 7.0 installation
I hope it will help you in understanding VC and its installation and How to work
Regards,
Rudradev Devulapalli.

Oracle Change and Configuration Management packs

Hi,
We are looking at implementing the Oracle Change and Configuration Management packs.
I would be very interested to hear from anybosy who is currently using these packs.
I have done some preliminary tests, and am getting what seems like a very simple error, but i am at a loss as to how to fix it.
Will respond to replies with exact error and scenario.
thanks in advance.
melvyn

Hi Nayab,
We are looking to implement the change and configuration management packs, to automate our change control.
As part of my initial testing i have the following scenario...
I have three database (namely TEST_DB, QA_DB and PROD_DB) all configured and manageable in EM.
I have create a sample test schema in TEST_DB with tables, views, sequences, procedures and triggers.
Using EM, i am able to transfer the sample schema (with all objects) from the TEST_DB to the PROD_DB.
If i manually create the sample schema in the QA_DB, i am able to transfer the sample schema from the QA_DB to the PROD_DBm using EM.
When i try to transfer the sample schema from the TEST_DB to the QA_DB i get an error in the synchronization phase.
The capturing of the baseline, and the dictionary comparison phase complete successfully, but when i do the synchronization phase, i get
the follwing error...
SQL> ERROR:
ORA-01034: ORACLE not available
ORA-27101: shared memory realm does not exist
SVR4 Error: 2: No such file or directory
Process ID: 0
Session ID: 0 Serial number: 0
This seems strange because, it must have been able to see the destination database for it to complete the dictionary comparison phase, so
i cannot understand now why it cannot connect to the destination database to complete the synchronization phase.
any assistance would be greatly appreciated.
thanks
Melvyn

Version control and configuration management

How is version control and configuration management done for iPlanet6 web
and app servers?

I'm not sure if I understand exactly what you are asking. Neither iWS or
iAS have built in version control or configuration management. But
pretty much everyone integrates them with version control or SCM in some
way. Ranging from the complex (say integrating iAS and Interwoven) to
the simplistic (using CVS to track HTML documents or source code).
David
Chris Valliere wrote:
How is version control and configuration management done for iPlanet6 web
and app servers?

Install vstf_testagent.exe and vstf_testcontroller.exe on remote machine and configure

Hi,
I am creating a form application where I want to install vstf_testagent.exe and vstf_testcontroller.exe on remote machine and configure it. I copied the files to the remote machine local directory, wanted to know how to install exe on remote machine and
configure it. could some one help me with code.
Thanks
Thanks,

Hi sayedfarhan,
Thank you for posting in MSDN forum.
>>I am creating a form application where I want to install vstf_testagent.exe and vstf_testcontroller.exe on remote machine and configure it.
According to your issue, as you said that you want to install vstf_testagent.exe and vstf_testcontroller.exe on remote machine and configure it.
So please you refer the following MSDN document to install and configure the test agent and test controller on this remote machine.
https://msdn.microsoft.com/en-us/library/dd648127.aspx?f=255&MSPPError=-2147217396
Generally, I know that we used this test controller and test agent to run automated tests on remote machine. Note:I know that if you want to install and configure test agent and test controller for automated test, it will not need to any code for
it.
So whether your issue is related to run your automated tests remotely with the test agent and test controller.
In addition, as you said that:
>>I am creating a form application where I want to install vstf_testagent.exe and vstf_testcontroller.exe on remote machine and configure it.
Could you please tell me whether you want to install and configure the test controller and test agent for your form app?
If I misunderstanding your issue, please tell me more detailed message about your issue.
Best Regards,
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

Integration Services 2012 - Parameters and configuration management

Our organization has implemented the project deployment model and it works great! It helps has helped us standardize deployment and configuration management. The big plus for us is the fact that we can now run reports on all SSIS
package configurations. There is one challenge though that we have come across. We haven’t found a good way to reuse the same ssis package while passing different parameters from different jobs and still be able to keep the configured parameter
values for each job documented in SSIDB; if you configure each job to pass different parameter values to the same package, the parameters are actually saved under the the job step’s command. The challenge is that there isn’t a clean way to retrieve
those parameters from msdb, unless someone out there has been able to? We need to retrieve the configured values to be able to build a report on all jobs and packages which contain all configured values. This makes our jobs easier when troubleshooting
a problem.
The only work around we have found is to simply create two different packages, one for each job. I have a problem with not being able to reuse a package from a conceptual stand point. I am sure there is someone out there that has come up with a
good solution. Can you please share it?
thank you,
Juan.

If I understand you correctly, you may be able to get what you want from catalog.execution_parameter_values catalog view
http://technet.microsoft.com/en-us/library/ff878152.aspx
Please Mark This As Answer if it helps to solve the issue Visakh ---------------------------- http://visakhm.blogspot.com/ https://www.facebook.com/VmBlogs

Re: BulletinBoard and configuration for Touchpad

Win7 x64
L505-10M
There ware all sorts of problems after a windows security update a few months ago for this system.
I have to put a backup of C:\ back, but various functions did not work .
I have most of them work again now. I installed Flashcard again but Bulletin Board and configuration for Touch pad are missing yet.
Mouse drivers are HID-mouse and PS/2 version: 6.1.7600.16385 of Microsoft.
I downloaded Touch Path Driver-20091202155841.zip but this cannot be installed.
C: \Program Line\TOSHIBA\Bulletin Board is present but probable damaged and not present in Windows Start-menu\Toshiba.
How can I repair this?
arnold12

I understand you that recovery installation is your last step and possibility.
What kind of backup do you have? How have you created this backup?
Obviously you have problems with typical Toshiba stuff so I dont understand what kind of backup do you use. Was your preinstalled OS screwed up and you try to install back up.
Anyway, bulletin board try to check Toshiba download page and install ReelTime for your notebook model, if it is offered.
What is wrong with touch pad driver? Why you cannot install it? Can you see some error message?
Have you tried to install both offered touchpad drivers? Which one cannot be installed?

Understand and configure CBQoS.-

Similar Messages

Maybe you are looking for