Use of ldm add-config

I am looking to add a new guest domain onto an existing LDOM system with existing guest domains. I am right in thinking that at the end of creating the new guest domain I must run "ldm add-config (newConfigName)" in order for the new domain to remain visible after a reboot of the primary domain server?
Ewan

Hi ,
You can configure any scenario through wizard or manually.
<i>
How to do configuration setps for the scenario using wizard and manually</i>
Create one by one step which is specified in the weblog with respect to source and target business system.
1)Create new configure scenario in ID
2)Import your BPM from IR.
3)Create communication channels in business systems under service without party.
4)Create three interface determinations
three reciever determinations and one sender agreement(For file system) and one two reciver agrements(one for file system and other for DataBase).
Check this blog for reference...
/people/arpit.seth/blog/2005/06/27/rfc-scenario-using-bpm--starter-kit
Sekhar

Similar Messages

When To Use redirect/ In faces-config.xml

In what situations should I use <redirect/> in faces-config. I understand what that using it causes it to generate a HTTP redirect instead of redirection through the view handler.
I have ran into situations where if I don't use redirect, evein in a request scoped bean data isn't completely cleared out of a form. IE I have a list of users with a list of their addresses. If I look at an address on user 1 I see the right details, if I then move to user2 and look at one of his addresses it reflects the information from user1. As soon as I add <redirect/> the problem disappears.

You normally use it to fire a brand new request.
If I look at an address on user 1 I see the right details, if I then move to user2 and look at one of his addresses it reflects the information from user1. As soon as I add <redirect/> the problem disappears.This rather sounds like faulty code logic. Debug it.

How to use the same services-config for the local and remote servers.

My flex project works fine using the below but when I upload my flash file to the server I doesn't work, all the relative paths and files are the same execpt the remote one is a linux server.
<?xml version="1.0" encoding="UTF-8"?>
<services-config>
    <services>
        <service id="amfphp-flashremoting-service"
            class="flex.messaging.services.RemotingService"
            messageTypes="flex.messaging.messages.RemotingMessage">
            <destination id="amfphp">
                <channels>
                    <channel ref="my-amfphp"/>
                </channels>
                <properties>
                    <source>*</source>
                </properties>
            </destination>
        </service>
    </services>
    <channels>
    <channel-definition id="my-amfphp" class="mx.messaging.channels.AMFChannel">
        <endpoint uri="http://localhost/domainn.org/amfphp/gateway.php" class="flex.messaging.endpoints.AMFEndpoint"/>
    </channel-definition>
    </channels>
</services-config>
I think the problem is the line
        <endpoint uri="http://localhost/domainn.org/amfphp/gateway.php" class="flex.messaging.endpoints.AMFEndpoint"/>
but I'm not sure how to use the same services-config for the local and remote servers.

paul.williams wrote:
You are confusing "served from a web-server" with "compiled on a web-server". Served from a web-server means you are downloading a file from the web-server, it does not necessarily mean that the files has been generated / compiled on the server.
The server.name and server.port tokens are replaced at runtime (ie. on the client when the swf has been downloaded and is running) not compile time (ie. while mxmlc / ant / wet-tier compiler is running). You do not need to compile on the server to take advantage of this.
Hi Paul,
In Flex, there is feature that lets developer to put all service-config.xml file configuration information into swf file. with
-services=path/to/services-config.xml
IF
services-config.xml
have tokens in it and user have not specified additional
-context-root
and this swf file is not served from web-app-server (like tomcat for example) than it will not work,
Flash player have no possible way to replace token values of service-config.xml file durring runtime if that service-config.xml file have been baked into swf file during compilation,
for example during development you can launch your swf file from your browser with file// protocol and still be able to access blazeDS services if
-services=path/to/services-config.xml
have been specified durring compilation.
I dont know any better way to exmplain this, but in summary there is two places that you can tell swf about service confogiration,
1) pass -services=path/to/services-config.xml parameter to compiler this way you tell swf file up front about all that good stuff,
or 2) you put that file on the webserver( in this case, yes you should have replacement tokens in that file) and they will be repaced at runtime .

Airport setup asst. doesnt work. Is there way to use Windows to add airpor

Airport setup asst. doesnt work. Is there way to use Windows to add airport express to my current linksys network so that my iTunes will play through my stereo?
Previously the air-assit recognized the air-exp unit but kept asking for a password to continue. I tried passwords like admin and public but nothing worked. Then Windows network connections kept trying to connect my laptop to the internet using the air-exp. Don't remember what I did to fix that problem but now my laptop doesn't try using it to connect me to internet anymore.
However, now air-asst. doesn't read the air-exp anymore. Windows network connections DOES read it now but doesn't try to use it anymore to connect me to the internet.
I have a linksys WAP and separate linksys router. If memory serves, when I firt got the air-exp about 6 months ago I could not connect either and Apple tech support had to help me. I think, but not sure, they had me use Windows to add the air-exp to my wireless network. Also if my memory serves me, but not sure, I had to type in either some IP or MAC addresses in order to get the air-exp to connect to my existing network. I DO remember thinking after it was finally working that "Wow, this is definately NOT a plug and play thing." It wasn't very easy to set up.
I lost my laptops wireless connection last week and couldn't connect to my network and had to call linksys tech support. They had me input a new IP and DNS address because somehow my laptop "lost" the previous ones. Since then I have not been able to use my air-exp to connect to my stereo.
I have called Apple tech support but since my 90 days is up they want to charge me $49.95 for up to five days worth of tech support. Which I think is a rip off becau linksys will help you out at anytime for fee but that's a topic for another discussion group. Common Apple, how about a $10 charge for one day of tech support, or even just 15 minutes worth to get my gear working again?
Anyway, if anyone knows of any on-line walkthroughs of how to deal with these airport express set-ups or problems please let me know. Or, of course if anyone can walk me through this that would be even better. THANKS

Thank you for your help.
When I run air-util a window called base station chooser comes up and all the fields are blank. When I push "re-scan" nothing happens. When I push "other" a window pops up asking for IP address and password. I typed in the IP address given to me from Linksys tech and tried to move on but it came back asking me to fill in the password. I tried the default linksys password "admin" but it came back with an error.
Do I hard (factory) reset the air-express by simply pushing the reset button or do I have to hold it in while I plug it in or simply push the button for a certain length of time?
Thanks again.

How to use *MonitorManager* to add custom messages in channel monitoring?

Hi experts,
How to use MonitorManager to add custom messages in channel monitoring for custom adapter development(Not in audit log).
like
Type Time Stamp Message ID Explanation
6/25/11 6:39:47 AM 00199942-6e43-02df-96ca-8b538c63dd98 Message processing completed successfully
6/25/11 6:39:47 AM 00199942-6e43-02df-96ca-8b538c63dd98 Message with ID 00199942-6e43-02df-96ca-8b538c63dd98 processed
6/25/11 6:39:46 AM 00199942-6e43-02df-96ca-8b538c63dd98 Message processing started
6/24/11 6:43:26 AM 00199942-6e43-02ef-96b1-7650f3495e03 Message processing completed successfully
6/24/11 6:43:26 AM 00199942-6e43-02ef-96b1-7650f3495e03 Message with ID 00199942-6e43-02ef-96b1-7650f3495e03 processed
6/24/11 6:43:24 AM 00199942-6e43-02ef-96b1-7650f3495e03 Message processing started
6/23/11 6:45:52 AM 00199942-6e43-02df-9698-5be345a9ddf5 Message processing completed successfully
6/23/11 6:45:52 AM 00199942-6e43-02df-9698-5be345a9ddf5 Message with ID 00199942-6e43-02df-9698-5be345a9ddf5 processed
6/23/11 6:45:50 AM 00199942-6e43-02df-9698-5be345a9ddf5 Message processing started
6/22/11 6:43:30 AM 00199942-6e43-02ef-95ff-2c03493dc078 Message processing completed successfully
Edited by: SAP_PI_D on Jun 28, 2011 12:10 PM

Solve by myself

Use DISM to add drivers returns an error on an image which has profiles and programdata on a seperate volume

Hi,
We capture and modify W7 Ent and Pro OS images on a regular base by using DISM to add drivers for example. Until now we never had a problem because we always had images which only had 1 OS volume captured. DISM works fine to mount the image to a mount
folder, add drivers, and save the changes in the image.
However now we encounter an issue when doing the same actions on an image where the \Windows folder was located on the C:\ volume and \programdata and \users folders where redirected to a D:\ volume.
When mounting the C:\ volume image (including everything except \programdata and \users folders) the error we receive when trying to add or get drivers is:
Error 3 - the \Windows folder is not a valid Windows directory.
The DISM.Log file show right before this error that the remote registry could not be contacted.
This is caused I think because the registry files are located on the \Users folder, but since this folder is not captured in the image (located on another volume during capture) it cannot find the registry.
My question is: how can we resolve this?
What we have now is 1 WIM file where index1 is the OS (C:\ volume) and index2 is the \ProgramData and \Users folders (D:\ volume). Probably the way of capturing the image and redirecting programdata/users is not done in a correct way...
Note: the image index1 and index2 restore works fine - the unattended.xml contains also redirection to the folders paths for \programdata and \users...
Any help or advice would greatly be appreciated!
Thx.
Steve
Wkr, Steve

Hi Steve,
You can be right that DISM don’t support the scenario that User profile and System are in the separated volumes.
As a workaround, we should use the defaults to put the profile on C: during capture image, and then set the profile path to be on the D: drive after the image deploying.
Please refer to below KB for how to using Sysprep to redirect profiles’ locations.
Customize the default local user profile when preparing an image of Windows
http://support.microsoft.com/kb/973289/en-hk
Hope these could be helpful.
Kate Li
TechNet Community Support

How to use FNDLOAD to add program to request group?

Is there a way to use FNDLOAD to add a program to System administrators > security > responsilibity > request.
I have try to use the following command to downlod this information to load it to other place but no record saved in ldt file:
FNDLOAD apps/apps1234 O Y DOWNLOAD $FND_TOP/patch/115/import/afcpreqg.lct PO_RESQUEST_GROUP_2.ldt REQUEST_GROUP REQUEST_GROUP_NAME="All Reports" APPLICATION_SHORT_NAME="XXPO"
OR
FNDLOAD apps/apps1234 O Y DOWNLOAD $FND_TOP/patch/115/import/afcpreqg.lct PO_RESQUEST_GROUP_3.ldt REQUEST_GROUP APPLICATION_SHORT_NAME="Purchasing" REQUEST_GROUP_NAME="All Reports" UNIT_NAME="XXPO_PUR_REQ"
if i delete APPLICATION_SHORT_NAME="Purchasing" , it downloaded many seemingly not relevant data as follow:
Downloading REQUEST_GROUP to the data file PO_RESQUEST_GROUP_3.ldt
Downloaded REQUEST_GROUP All Reports CUN
Downloaded REQUEST_GROUP All Reports IGS
Downloaded REQUEST_GROUP All Reports PSB
Downloaded REQUEST_GROUP All Reports CSE
Downloaded REQUEST_GROUP All Reports AHL
Downloaded REQUEST_GROUP All Reports ENI
Downloaded REQUEST_GROUP All Reports OFA
Downloaded REQUEST_GROUP All Reports XTR
Downloaded REQUEST_GROUP All Reports SQLAP
Downloaded REQUEST_GROUP All Reports PO
Downloaded REQUEST_GROUP All Reports CHV
Downloaded REQUEST_GROUP All Reports QA
Downloaded REQUEST_GROUP All Reports CE
Downloaded REQUEST_GROUP All Reports POA
Downloaded REQUEST_GROUP All Reports MFG
Downloaded REQUEST_GROUP All Reports CRP
Downloaded REQUEST_GROUP All Reports WIP
How can I confine "Application"? which is under the field "Group" and how can I download all application named "custom puchasing" next to "Name"?

When migrating to another instance and want to add a concurrent program to a request group, I do it in two steps. Within a shell script, I call
1 - FNDLOAD to load ldt file (concurrent program definition)
2 - SQLPLUS to run an sql file that call FND API that install concurrent program into proper request group.
ex # 1 :
FNDLOAD $apps_user/$apps_pswd@$dbsid 0 Y UPLOAD $XDO_TOP/patch/115/import/xdotmpl.lct $XX_TOP/XX_PGM.ldt - WARNING=YES CUSTOM_MODE=FORCE >> $LOG_FILE 2>&1
ex # 2 :
sqlplus -s $apps_user/$apps_pswd@$dbsid @$XX_TOP/XX_PGM_REQ_GROUP.sql >> $LOG_FILE 2>&1
XX_PGM_REQ_GROUP.sql content.
IF NOT fnd_program.program_in_group('XX_PGM','Business Online','GL Concurrent Program Group','General Ledger' ) THEN
fnd_program.add_to_group(program_short_name => 'XX_PGM',
program_application => 'Business Online',
request_group => 'GL Concurrent Program Group',
group_application => 'General Ledger');
COMMIT;
END IF;
Hope this might help.

I was running Foxfire 3.6.9 and wanted to use FTP Program add-on and it did not appear to load but appeared but then would be installed but not run or appear under tools. So I deleted Foxfire 3.6.9 and down loaded to 3.5.9 so it could get FTP and it is do

I was running Foxfire 3.6.9 and wanted to use FTP Program add-on and it did not appear to load but appeared but then would be installed but not run or appear under tools. So I deleted Foxfire 3.6.9 and down loaded to 3.5.9 so it could get FTP and it is doing the same could not install. Even after I registered my copy. The last time I used this program it showed up under tools and worked great. any suggestions on whats going on and how I can get around this?.by ralphd3g

Delete the files extensions.* (extensions.rdf, extensions.cache, extensions.ini) and compatibility.ini in the Firefox [[Profiles|profile folder]] to reset the extensions registry.
See "Corrupt extension files": http://kb.mozillazine.org/Unable_to_install_themes_or_extensions
If you see disabled extensions that are not compatible on the next start in "Tools > Add-ons > Extensions" then click the "Find Updates" button to do a compatibility check.

How to use BAPI to add a new version for a claim number in WTY transaction.

How to use BAPI to add a new version for a claim number in WTY transaction.
I am using function module " BAPI_WARRANTYCLAIM_ADD_VERSION ".
It needs to copy all contents of previous version to a new version.
While doing so i am unable to copy fields like valic valoc etc. Any ways by which i can copy this values.
WTY will update PNWTYH , PNWTYV and PVWTY tables.
Thanking you,
Lokesh.

Hi Vishnu,
You can do that through EEWB. Please go through SAP Note 484597. You would get the details of using Easy Enhancement Work bench.
Rewards point if you think this info is useful
Regards,
Dipender Singh

How can you detect irregular edges using the IMAQ add on?

Im currently trying to use the IMAQ add-on for LabView to detect the edges of an irregular image. I have attached the image I am trying to detect the edges of. I have tried using everything in the "locate edges" sub-pannel (i.e.. imaq find edge, imaq find circular edge etc.) but none of them have yielded any favorable results. I think the "IMAQ edge tool 3 IV" might be what im trying to find however I don't understand how to get any usable data out of it.
Thank you, all comments and help are greatly appreciated.
Attachments:
waveguide.png ‏516 KB

Hi Dander,
I am not sure exactly what types of edges you are trying to acquire, but I used one of the examples from our Example Finder and was able to detect edges on your image. I will say that with the image that you are using, the edges are not very well defined, so you may not get a 100% accurate measurement. The example that I was using uses the IMAQ Edge Tool 3 VI and the example can be found by going in LabVIEW to Help>>Find Examples... From there, you will go to Toolkits and Modules>>Vision>>Functions>>Edge Detection Example.vi. After that, you will remove the build path function and input a path to the image. I hope this helps!
Kim W.
Applications Engineer
National Instruments

I have the 4.0 and I use the greasemonkey add ons. They worked fine on the 3.0, but when I updated to the 4.0, it freezes up, I need help please.

When I upgraded to the 4.0 Firefox, I have been having severe issues w/ Firefox not responding & freezing up. I use the GreaseMonkey add ons w/ it. I am leery about going to the 5.0 as of the problems I am having and that of my friends problems with the 5.0 & GreaseMonkey. I want to go back to the 3.0 Firefox. I need to fix this.

I get the add-on manager start to load up but then it crashes after a few seconds, if I try to click extentions or something else it still has the same effect of the browser crashing! Please help

Can you explain when using keywords and addding them to various clips pressing ctrl and a number eg. 1 or 2 it simply closes down FCPX. Just to the dock as would th yellow -sign. As you gather I am new to this program having only used Final Cut Express 4

Can you explain when using keywords and addding them to various clips pressing ctrl and a number eg. 1 or 2 it simply closes down FCPX. Just to the dock as would the yellow -sign. I am new to this program having only used Final Cut Express 4 previously.
iMac (early 2009) 24in 2.93GHz 4GB 1066MHz DDR3 SDRAM (To be upgraded ot 8GB in the nextfew days) os x 10.7.2 Lion
Re: Why don't my arrows on the time line operate and allow me to move to the start and end of the timeline. Iam using the trial version

Check System Preferences. I think Control-1 is used by something in the OS now. Switch it off. It's a major p[ain the way the OS is taking over more and more of the keyboard, allowing less options for application use.

How can i use excel's add-ins, solvers, .xla etc...?

I want to use excel solvers(add-ins, .xla documents) with numbers. Is it possible ?

No.
http://www.apple.com/feedback/numbers.html

[svn:bz-trunk] 17931: Add config suite test for BLZ-540.

Revision: 17931
Revision: 17931
Author:   [email protected]
Date:     2010-09-29 11:28:46 -0700 (Wed, 29 Sep 2010)
Log Message:
Add config suite test for BLZ-540. BlazeDS configuration files should not allow external entities.
Ticket Links:
    http://bugs.adobe.com/jira/browse/BLZ-540
Added Paths:
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/services/ExternalEntityInConfigT est/
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/services/ExternalEntityInConfigT est/error.txt
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/services/ExternalEntityInConfigT est/services-config.xml

If you include the xalan.jar library to the build.xml execution classpath everything works!!!!!!.
I hope it will be userfull.

[svn:bz-trunk] 9570: Add config suite test for BLZ-361.

Revision: 9570
Author:   [email protected]
Date:     2009-08-25 07:29:50 -0700 (Tue, 25 Aug 2009)
Log Message:
Add config suite test for BLZ-361.
Ticket Links:
    http://bugs.adobe.com/jira/browse/BLZ-361
Added Paths:
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/channels/clientLoadBalancing/
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/channels/clientLoadBalancing/NoU RLsTest/
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/channels/clientLoadBalancing/NoU RLsTest/error.txt
    blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/channels/clientLoadBalancing/NoU RLsTest/services-config.xml

If you include the xalan.jar library to the build.xml execution classpath everything works!!!!!!.
I hope it will be userfull.

Use of ldm add-config

Similar Messages

Maybe you are looking for