When listening to an audio book it freezes after about 10 minutes. I have done a soft reset, I have deleted the audio book and re- installed. My music plays with no problem.

Using my ipod nano -when listening to an audio book it freezes after about 10 minutes. I have done a soft reset, I have deleted the audio book and re- installed. My music plays with no problem.

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

Similar Messages

Arch freezes after about 10 minutes with new kernel [SOLVED]

As the title says: Arch freezes after about 10 minutes with new kernel (2.6.27). I can only move a mouse, but everything else is frozen. Even restarting X doesn't do a trick. It doesn't work at all. Frozen.
I don't get any kind of error message (oh really?), so what's the problem..?
Last edited by Exitium (2008-10-22 15:29:27)

juan_sck wrote:
Exitium wrote:
test1000 wrote:I had an issue with only being able to move the mouse after logging in from gdm and nothing happening but i don't know if thats the same error Sooo, are you using the right nvidia drivers? their driverpolicy just changed, and we now have 4 different official nvidia drivers in repo :S
Yeah... I'm using nvidia... So the problem is nvidia drivers, not the Linux kernel?
Edit: My card is nVidia GeForce 8800 Ultra. I can't get driver information now, because I'm using WinXP right now. I'll check it later.
Did you make a new install or just updated?
You can try to reinstall old kernel with:
pacman -U /var/cache/pacman/pkg/kernel(version you want).pkg.tar.gz
if you made a new install you may have to install the xorg keyboard driver and so.
By the way, there are a few diferent packages for nvidia drivers. Check wich is yours.
Also check /var/log/ folder for errors.
Updated kernel.
And as I said, I'll check the driver later.

My imac 17' core duo 1.8ghz a1173 freezes after about 1 minute of running

My imac 17" core duo 1.8ghz A1173 freezes after about 1 minute of running. I re-start the imac about a half a dozen times and it stays running and will re-start from the sleep mode and will continue to operate properly until I put it in sleep mode or it goes to sleep mode. If I turn it off, I must go through the same hassle. Advise/suggestions. Thanks.

Hello arty102
Welcome to Apple Support Communities
Reset the SMC > http://support.apple.com/kb/HT3964
+1. Shut down the computer.+
+2. Unplug the computer's power cord.+
+3. Press and hold the power button for 5 seconds.+
+4. Release the power button.+
+5. Attach the computers power cable.+
+6. Press the power button to turn on the computer.+
Then if that doesn't help,
Run the Extended Apple Hardware Test > http://support.apple.com/kb/HT1509
Dennis

TS3354 Cannot downloading TV movies. Itune attempts download but then freezes after about 1 minute into the download. Download status first states video will take 37 then 45 hours to download

Cannot downloading TV movies. Itune attempts download but then freezes after about 1 minute into the download. Download status first states video will take 37 then 45 hours to download. My computer more than meets the minimum requirement for HD downloads...not sure about the HDCP capability

Hi 1611kjb,
Please refer to the solution mentioned in the following threads :
http://forums.adobe.com/message/5396792#5396792
http://forums.adobe.com/message/5409050#5409050

So , It was Late At Night And I Put My Ipad On The Chager , And When I Woke Up It Is Not Turning On , Or It Is Not Charging , I Tried To Reset It By Holding The lock button And The Home Button But It Is Not Working

So , It was Late At Night And I Put My Ipad On The Chager , And When I Woke Up It Is Not Turning On , Or It Is Not Charging , I Tried To Reset It By Holding The lock button And The Home Button But It Is Not Working

Hello ipadisbroken,
Thank you for using Apple Support Communities.
For more information, take a look at:
iOS: Not responding or does not turn on
http://support.apple.com/kb/ts3281
Have a nice day,
Mario

ITunes freezing after about 5 minutes on one account, works on other accounts

background info: I have a 2008 black Intel Macbook 2.4 GHz with 2GB RAM.
the problem that I'm having is when I run iTunes , after about 5 minutes even if I'm not downloading or playing music, the program starts to slow down and I get the rainbow beach ball on my screen. If I'm playing music, it starts and then stops, starts, and stops. Other programs respond for about a minute, and then nothing responds, no force quit, no nothing. The only way to get my computer back is to hard restart.
**I have a feeling that gapless playback has something to do with it, the problem started when I added an album collection of around 800 songs at once, and I did notice that it starts going through the gapless playback analysis or whatever and then freezes.
I've tried reinstalling iTunes etc. and searching forums and websites, but all problems that sound similar are from years ago and different iTunes versions. The iTunes is the version before 10.4, I'm not sure if its 10.3 or 10.2, since I'm afraid to open it and have my computer crash again.
One annoying fix I did was when I need to have music I made a separate account on my mac that runs iTunes fine with no problems. I had this problem in Snow Leopard, and just upgraded to Lion hoping it would fix itself, but it still has the same problem.
If anybody has help or has a similar problem please let me know.

Scanning from other than admin account has always been a problem for me. The only solution that I found out working is using the Vuescan software. It has something to do with that the scanning software trying to access some part of OS X that is locked to others but not for the owner (admin).
To give the other accounts admin access doesn't help.
//Peter

After Replacing Hard Drive, iMac Freezes after about 40 Minutes.

I have a flat panel 15" iMac which had a bad hard drive. I replaced it with a 250 gig Seagate ATA drive. I used the Disck utility to format it and the computer recognized the correct size of the Drive. After installing OS 10.4.7 on the drive I found that the computer locks-up or frezzes after about 45 minute. I have run apple diagnoxtics and the computer hardware and ram checks out fine. I found that the computer does not lock up if I runit form an external firewire drive with os 10.x and it did not lock-up when I booted form the OS 9 Hardware test cd. I then thought that maybe I had loaded the OS x poorly on th e new drive so I reloaded the OS. The system agin freezes agter the system is on for about 30 + minutes.
Do I need a special drive or size for the G4 flat panel iMac? Is there a setting on the Segate Drive I need to set.
Any Thoughts\
Jim
G4 Dual 1.25 Mac OS X (10.2.x)

Hello,
There should be a Master / Slave setting on the drive. If it shares the same "channel" with your CD-ROM drive, then you may need to set the Hard Drive as Master.
Check your original drive, and see what it was set to. There is a Master, Slave, and Factory setting.
Look at the label on the drive, and compare that to the jumpers (little caps) on the back of the drive by the data cable connector.
Set your new drive to match the same setting your original drive was set to.
If that doesn't work, try your new drive in the external drive enclosure. See if it works right there.
If it still doesn't work right, then perhaps you got a drive with a defect.
If it works fine in the external case, and you have verified that your settings are right when used internally, then you may have damage in the iMac's logic board or hard drive controller somewhere.
But, take a look at the Jumper Settings, and try it in the external enclosure as well. See if either of those fixes it.
Hopefully you just got the jumper settings wrong.
I hope this helps.

I am having problems with my Mac Book Pro Retina locking up after updating from Lion to Maverick. I was having no trouble until I did the upgrade, and now it is locking up, freezing after about 5 minutes, and getting hot. Any suggestions?

A while back I had an upgrade available to me. I had Lion when I bought this Pro. The upgrade is Maverick. After downloading and installing the upgrade, my computer started freezing while doing anything. I might not get this completely written before it freezes. The keyboard is getting hot, and I have to use the power button to turn it off. After it has sat for at least 10 minutes, I can turn it back on. I might be able to do some work for 5 minutes, or up to 30 minutes before it freezes again. Some of my programs are not working, either.
I would appreciate any suggestions anyone might have, or even go back to Lion, if I can figure out how to.
Thanks.

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

Hi I have a newish MBA approx 1 year old that was running mountain lion. I think i have deleted the entire system and any partitions it boots and says no bootable drive when i try cont R it starts internet recovery but just sits there

Hi during playing around with my MBA i think i have despite all the warnings deleted everything from my laptop. I do not have a back up or usb start up. when i boot the laptop it says no bootable device found, i have tried various configerations of alt cntr r etc the best i can get it to is a spinning grey globe that says looking for internet connection. it does not see my wifi so i do have a usb-rj45 adapter that if i plug into the R/H side usb port lets it see the internet (i think) it then brings up a down load bar but this never moves and in the end brings an error nummber up i think it was -0007 or -0002.
Do i have to buy new mountain lion or usb start up stick
I have access to a windows PC (not mac) so can use this to create a usb if someone helps an idiot out
thanks Martin

I had just finished backing everything up and was about to hit the wipe button when I found a solution that worked for me: here: https://discussions.apple.com/thread/4144252?tstart=0
It gdisk to be installed, and a bit of terminal knowledge, but it fixed the problem for me. For this step:
add partion 5 to the MBR
It was partition 4 for me. You should first use gdisk's 'p' command to find the number of your bootcamp partition, and then use that number.

I keep getting old settings when I try to install Firefox again. I have deleted the program files and the profile, but the program is finding the old bookmarks and settings somewhere. How do I delete this information to make a clean installation?

I have a corrupted bookmark file and want to totally delete any information on the bookmarks and settings. I have deleted any files which reference Mozilla and Firefox from my hard drive and have gone into the Registry and deleted all references to Firefox. But every time I reinstall Firefox the program finds this information. Is it in the sync folder and how do I clear out that folder?

http://support.mozilla.com/en-US/kb/Backing+up+your+information

Firefox was working fine and suddenly it could not access the proxy server; I deleted the program, downloaded and re-installed. same problem - what gives?

I have Opera, internet explorer, and safari on my pc. they are still fully functional buy firefox has become unable to connect

You can find the connection settings in Tools > Options > Advanced : Network : Connection
If you do not need to use a proxy to connect to internet then select "No Proxy"
See "Firefox connection settings":

Zen Sleek Photo Freezes/Locks Up after about 5 minutes usage (need to drain battery to recov

Hi,
My 20G Zen Sleek Photo has just recently transformed itself into a useless brick.
No matter what I try and do, it always ends up freezing after about 5 minutes usage. When you force a reset it does unlock but when it comes back on it sticks on the Creative "copyright" start up screen.
I've reformatted and re-installed the firmware several times but with the same result.
font face="comic sans ms,sans-serif">
The only time it totally unlocks is when you either:
() let the battery fully drain and then recharge it or
(2) you disconnect the battery lead and then press the On/Off switch for several minutes.
I've looked everywhere for a solution/reason but nothing. You find plenty of people with the same problem but no answers. Surely someone knows how to fix the problem
Is it a faulty battery (unlikely because mine charges up fine and holds it charge well)
Is it the hard dri've (very unlikely since the player can start up correctly [given the above recovery procedure] and play tracks within the 5-0 minutes you have available)
Is it the firmware (I doubt it, I can't see what the firmware's got to do with a delayed lock up, having worked fine up to that point)
Is it the motherboard (maybe....., to my mind it points to a component failure that allows an electric charge to build up and not dissipate, the only way to discharge it is to short the battery pins [with, I hasten to add, the battery removed!])
font face="comic sans ms,sans-serif">
Has anyone within the Creative community successfully solved this problem Has anyone received a decent answer from Creative
I find it staggering that the guys at Creative have washed their hands of this problem. They, after all, are the most likely people to identify the problem - only they have a schematic of the motherboard that would allow them to investigate and locate the problem.
For the record the firmware I'm using is v .0.0.
Any guidance would be much appreciated,
Victor

Is there really no one with an answer to this problem or have I overlooked a previous post that explained the fault.
BR
Victor

TS2755 When I click on a IPhone number in contacts to send a message. It keeps trying to send the message to the land line. I deleted the whole contact and re-entered it. But, still wants to send to the land line instead of the IPhone.

When I try to send messages to another IPhone.
I go to contacts.
Touch IPhone number.
Type message.
Hit send.
Comes back to me.
"Can not send messages to land line"
Well I did not touch the land line number - I touched the IPhone number.
I have deleted the whole contact, and re-entered it.
I have turned the IPhone off and on.
Still I get this message on only two of my contacts.
HELP

I can't delete my question, so I'll just say that you press on the type of number written in the box to the left of the box you typye the number into. Dumb or what?

HT204291 Since downloading 8.1.3 onto my iPad, video streaming through my Apple TV freezes after a few minutes whilst audio continues as usual. Anyone experienced this and if so, is there a fix?

Since downloading 8.1.3 onto my iPad, video streaming through my Apple TV freezes after a few minutes whilst audio continues as usual. Anyone experienced this and if so, is there a fix?

8.2 is out...perhaps that will address your problem.
Barry

I'm having trouble updating my iphone 4 since i updated to 4.3.3 i can't update it anymore. right now when i connect it to my itunes, itunes freezes for about 5 minutes then says something like "could not load sync service" any ideas on what i shud do?

I'm having trouble updating my iphone 4 since i updated to 4.3.3 i can't update it anymore. initially itunes would let me go so far as downloadin the new software then an error poped up as soon as the download finished, and now when i connect it to my itunes, itunes freezes for about 5 minutes then says something like "could not load sync service, reconnect or try again later" any ideas on what i shud do?

Did you try to connect in recovery mode? iPhone and iPod touch: Unable to restore

When listening to an audio book it freezes after about 10 minutes. I have done a soft reset, I have deleted the audio book and re- installed. My music plays with no problem.

Similar Messages

Maybe you are looking for