Which is the maximum number of simultaneous IP sessions on 7600 with/out SAMI?

Please I need help from someone who has ever wondered and get to know the maximum number of simultaneous IP sessions on 7600.
On the documentation, this is the applicable information that we find regarding the number of sessions:
http://www9.cisco.com/en/US/docs/ios/isg/configuration/guide/isg_acess_sub_sessns_ps6922_TSD_Products_Configuration_Guide_Chapter.html
Beginning in Cisco IOS Release 12.2(33)SRE, the Cisco 7600 router supports IP subscriber sessions only on the SIP400 and ES+ line cards
The Cisco 7600 router enforces limits on the number of IP subscriber sessions per line card and router chassis. If the number of active sessions exceeds the following limits, an error message displays:
- Cisco 7600 chassis—32,000 subscriber sessions (supported in Cisco IOS Release 12.2(33)SRE1 and later releases)
- ES+ line card—4000 subscriber sessions per port group; 16,000 sessions per line card (supported in Cisco IOS Release 12.2(33)SRE and later releases)
- SIP400 line card—8000 subscriber sessions (supported in Cisco IOS Release 12.2(33)SRD4 and later releases)
Let us suppose that we use the SIP400 line card, since ES+ is far from our networking requirements.
Please confirm/answer the following:
No special license is required to use ISG with SIP400.
Is the 8000 session limitation per SIP400 module or per SPA attached to it?
I read in the documentation, that the SAMI card enhances the maximum number of ISG sessions:
http://www.cisco.com/en/US/docs/ios/isg/configuration/guide/isg_sup_sami_blade.html
The ISG Support for SAMI Blade feature combines the subscriber management features and functions of the Cisco Intelligent Services Gateway (ISG) with the processing power of the Cisco Service Application Module for IP (SAMI). The Cisco SAMI blade has six PowerPC (PPC) processors and occupies just one slot in the Cisco 7600 series router. This means that you can support many ISG features for up to 600,000 subscribers on a single router. 
We then assume that the SAMI blade overcomes the limitations noted above: 32,000 session/chassis and 8,000 sessions/SIP400. Correct?
No extra license is required to use ISG with SAMI.

How I can load a license in a home agent (modulo SAMI), which is installed in a 7606-S router?.

Similar Messages

  • What is the maximum number of devices that can be connected with FaceTime?

    I have tried to find in theh Apple web pages the maximum number of devices that one can connect to with FaceTime. Specifically, how many iPad2 or iPad (new) devices can connect to each other with FaceTime? What about an older iMac running Mountain Lion with iPads? Or, iPhone4s and iPads? Thanks for any information you can provide.

    I don't know of any limit, as long as each device has its own individual identification ( e-mail address, or phone number for iphones)

  • What is the maximum number of samples that can be acquired with a single trigger using PCI-6036E DAQ card?

    1. My PCI-6036E card has a FIFO of 1024 bytes in AI. Maximum how many samples can be acquired with single trigger for digitizing a waveform?
    2. PCI-6036E DAQ card has got a AO with 10ks/s update rate? Can I generate a pulsed output with the AO of this card? I need a pulse of, say, 5 V and 1 kHz frequency.

    Giri,
    1.The trigger is usually for enabling the acquisition. I mean, when it is logic zero, you acquire nothing; however, when it is logic one, you start acquiring your waveform,and you can acquire continuously without having to worry about how many samples, unless you want to set your program for doing so. You can acquire continuously by implementing buffer acquisition. Finally, the FIFO that is in the board will not affect the buffer acquisition.
    2.Yes, you can do that! You can generate your 5V signal with that specific frequency, and you should not have any problems, because the freq fits in the update rate.
    I hope this information is helpful.
    L Aguila
    Applications Engineer
    National Instruments

  • How to change the maximum number of process per user in BW ?

    Hi,
    Do you know how to change the maximum number of process allowed per user ?
    With RSRT we can customize the number of process per query but I don't know where we can customize the maximum number of process per user.
    In fact, my production environment reach always the max number of process available in SM50...
    Thanks a lot

    Hi,
    A user is not have the No. of processor but a work process can handle N No. of users. If a user hit any transaction v acn say from  a list of N worl proceesor which has been taken the work.
    Correct if I am wrong.
    Regards
    Syed.

  • Maximum Number of Simultaneous Requests

    I want to update the Maximum Number of Simultaneous Requests
    from 4 to 6 or 8. A restart of ColdFusion Application Server is
    required for changes to take effect. Has anyone experienced
    problems with the change not taking effect and/or causing the
    service to not restart.
    This has not happened. Being precautionary. The reason for
    the question is that I made a change previously to the Max Heap
    size from 1023 to 1535 in CF Admin, but when I attempted to restart
    the CF service it would not. Finally had to change the Max Heap in
    jvm.config back to 1023. Unsure why that would not accept it. The
    variable is that the service is running with a non-admin user ID on
    the server. Thoughts?

    The prevailing wisdom from Adobe for simultaneous requests is
    very wrong and inaccurate. First off, editing the simultaneous
    requests in the CFAdmin is safe to do. Editing your JVM settings
    with the CFAdmin is very dangerous on Linux because the CF Admin
    code can mangle the xml file. I'm not sure if this is true on
    Windows.
    Now back to the simultaneous requests issue. If you have high
    traffic and enough server processing power you can greatly increase
    the request number. We currently run our CFMX 7.02 servers set to
    100 simultaneous requests. And yes we've been maxed out at that
    level. We see over 1.5 million page views per day on a single cf
    server with only one instance of CF. As of today we switched to a
    load balanced setup and split the load across two servers. The
    reason we went load balanced is that we're expecting to more than
    double our traffic. Anyways, the number of simultaneous requests
    can be much higher than the 'General Wisdom' at Adobe.
    Oh yeah, I almost forgot. I've seen the new setting for
    simultaneous requests take effect with out having to restart CFMX.
    Cheers,

  • What is the Maximum Number of Concurrent Sessions allowed on a Shared Exchange Mailbox ?

    Hi,
    I have a query that how many concurrent sessions are allowed on a Resource Mailbox ?
    E.g. I have a scenario in which i run a Helpdesk, and it has an email address ([email protected]), where company employees can email thier IT Issues/requests.
    Now I have hired say 50 Service Desk agents, now is it possible that all 50 can access the IThelpdesk mailbox at one time ? Are there any limits on the number of the concurrent sessions of the mailbox ? What are the the permutations and combinations in this
    case ?
    ** The mailbox is on Exchange Server 2003**
    Regards,
    Tojo Thankachan
    +91 7875039665

    Hi,
    Exchange Server 2003 SP1 imposes a restriction on the number of permitted MAPI sessions per user. By default, the maximum number of permitted MAPI sessions per user is set to a hexadecimal value of 0x20 after you apply Exchange Server 2003 SP1.
    Generally, Event ID 9646 will be logged in the application event log of your Exchange Server 2003 computer when a client opens many MAPI sessions. Here is a KB descripted the details of it:
    http://support.microsoft.com/kb/842022
    For more information about MAPI session limit, please refer to:
    http://technet.microsoft.com/en-us/library/dd159906(v=exchg.80).aspx
    Thanks,
    Winnie Liang
    TechNet Community Support

  • Maximum Number of Concurrent User Sessions Limit?

    Please can you tell me if there is a limit for the maximum number of concurrent users sessions that can access the Portal? If so, where is the setting and how do I change it?
    By the way, I am not experiencing any issues; I am asking purely for information purposes
    Thanks.

    There used to be under one of the services in service configuration.  I thought it was under portal runtime, but I can´t see it now.  It mentioned it in the TZTEP1 course, but I haven´t got it with me.
    Having said that, I don´t know if it worked!
    Paul

  • How can we increase the maximum number of records which we export from UME

    Hi All,
             Is there any way to increase the maximum number of records which we can export from the UME.
    Please give your valuable suggestions as soon as possible.
    Thanks in Advance
    Regards,
    Ramalakshmi.S

    I didn’t find any configuration you can set to increase the number. I think it is related UI. The number is designed programmatically.
    Lisa Zheng
    TechNet Community Support

  • What is the maximum number of users that can be simultaneously connected to a shared drive on an Airport Extreme

    What is the maximum number of users that can be simultaneously connected to a shared drive on an Airport Extreme?

    50
    I haven't tried this, but imagine that things are going to be quite slow.

  • Stream analytics - Exceeded the maximum number of allowed receivers per partition in a consumer group which is 5

    Hi,
      I have configure stream analytics to read messages from eventhub and I am getting this error message:Correlation ID:
    e185534f-9e82-4efc-8050-5294796fb275
    Error:
    Exceeded the maximum number of allowed receivers per partition in a consumer group which is 5 TrackingId:4569eca8-cb70-4c50-96cd-5868bfbc3e37_B45,TimeStamp:1/7/2015 11:40:37 PM TrackingId:f408292e-0dab-40cc-8ae9-2730313c3241_B45, Reference:8fca3c6a-b0d1-41cf-a835-f7c74a2ea8c3,
    Timestamp:1/7/2015 11:40:37 PM
    Message:
    Exceeded the maximum number of allowed receivers per partition in a consumer group which is 5
    Message Time:
    2015-01-07 23:40:38Z
    Microsoft.Resources/EventNameV2:
    sharedNode92F920DE-290E-4B4C-861A-F85A4EC01D82.naveenevents_0_c76f7247_25b7_4ca6_a3b6_c7bf192ba44a#0.output
    Microsoft.Resources/Operation:
    Receive Events
    Microsoft.Resources/ResourceUri:
    /subscriptions/f122f431-ddc7-4e21-ae3a-f6a9e1273bcb/resourceGroups/StreamAnalytics-Default-Central-US/providers/Microsoft.StreamAnalytics/streamingjobs/Naveenstreamanalytics
    Type:
    EventHubInputAdapterEventHubFailure
    Any help on the same is appreciated.
    Thanks
    Naveen

    Hi Naveen,
    Thanks for reporting this issue. We are taking a look at this issue.
    Questions:
    Do you have multiple readers reading from this EventHub, or have you setup multiple Stream Analystics jobs reading from this event hub. You are hitting a limitation of how many readers are allowed per EH consumer group.
    What is the serialization format of your input (JSON/CSV)? Could you please verify the serialization format setup in the streaming job and if it matches your data?
    Thanks
    Zafar Abbas

  • Increasing the maximum number of sessions

    Hi,
    I am working on a web application which requires 3000 concurrent users as a part of the NFR and almost all of them would trigger operations which would require DB hits. Hence my Oracle server (10g) needs to support at least 3000 sessions. I checked the value in the V$parameter. Currently the value for sessions and process is set to 170.
    I guess to increase the value i would need to change it in the init ora file and restart the DB. I have the following doubts -
    1. What would be the basic system configuration (for the server machine) to support 3000 sessions?
    2. What are the other related parameters which need to changed? What values need to be set for the same and how do we calculate the same. Is there any model which can be used for calculations purposes.
    3. Are there any in built mechanisms supported by Oracle to handle such high load? I presume there should be available and i am blissfully unaware about of it !
    Request you to kindly guide me accordingly. Any help / pointers are greatly appreciated !!
    Thanks & Regards,
    Sriram

    The problem i face is if i limit the pool size to 300; then there is a good probability that while 3000 users access the application simultaneously reposes will be greatly delayed as the connections would be used up. This would affect the NFR.
    Also setting the increment value for the pool does not help pas the server limits the maximum number of connections. I am simultaneously checking the code to ensure that there is no connection leak. As this might also aggravate the probelm. On initial analysis i do not find any such issues.
    I am also parallely looking into the design to check if any of the frequently used data can be cached on the application server to improve performance and reduce the number of DB hits.
    Hope i am on the right track. Do let know your thoughts and suggestions.
    Thanks a lot for highlighting the issue.
    Thanks & Regards,
    Sriram

  • Maximum number of simultaneous Template requests

    I am running a CF-server (standard) on a
    Intel(R) Xeon(R) CPU           E5420  @ 2.50GHz, 8 cores
    I have read somewhere on the net that you can set 8-10 maximum number of simultaneous template requests per core, which in my case
    would be 64-80 simultaneous template requests.
    Is that a correct assumption?
    This does feel quite high considering the default value of the server is 10 simultaneous requests.
    //Toby

    It is the common rule of thumb, but that does not make it the correct or incorrect assumption.
    What it does make is a common and usefull starting point, with the strong assumption that one will then load test ones system to make sure the setting accually works well with ones applications and hardware.  And that one will then adjust accordingly based on the testing.

  • How to set up the maximum number of messages on a queue programmatically

    Hi,
    I am using IMQ 3.5 to implement a message layer for one of my projects. I created a "Job Status Queue", which receives job status report from a java application every minute. But I just want to keep the most current status report instead of all the job running history. How can I restrict the maximum number of messages to 1 programmatically?
    Any suggestion or help will be appreciated.
    Xiaoyun Tang

    You can't limit the destination size programmatically, but you can do it administratively and associate a behavior to occur when the limit is reached. In your case it sounds like you want a queue, 1 message deep, and to discard the oldest message when the queue is full. When you create the physical queue on the broker you can specify these attributes (you can also update them on an existing queue). For example:
    imqcmd create dst -t q -n StatusQ -o maxNumMsgs=1 -o limitBehavior=REMOVE_OLDESTFor more information see Chapter 6 of the Message Queue Administration Guide. In particular the "Managing Destinations" section:
    http://docs.sun.com/app/docs/coll/MessageQueue_35_SP1
    Joe

  • I am trying to setup iCloud account and when I login I see a popup. The Maximum number of free accounts have been activated on this iPhone. Pls, help me fix it. What other accounts? Thanks

    I am trying to setup iCloud account and when I login I see a popup. The Maximum number of free accounts have been activated on this iPhone. Pls, help me fix it. What other accounts? Thanks

    Then you'll have to use another iOS device or Mac running OS X Lion or higher to create a new account for you to use on your phone.  If you don't have one, perhaps a friend would allow you to create and account on their device (note: this will use one of their three maximum accounts).  To do this, they would need to go to Settings>iCloud, tap Delete Account (which will delete the account from their device but not from iCloud), then allow you to sign back in with your ID to create the new account.  Then tap Delete Account to delete the new account from their device, and finally, sign back in with their iCloud ID to restore their iCloud account to their device.  Then you can sign in with your ID on your phone in Settings>iCloud and use the new account.

  • What is the maximum number of pages (2-sided)?

    Hi,
    I am laying out a photo book with about 62 pages (which is 31 double-sided sheets), plus the covers. It contains 119 photos in total. When I try to add 1 more photo, a pop-up window tells me that I have more than 50 pages, so I have to delete some. The Apple web site says the large, double-sided books cost $29.99 for 20 pages (10 sheets), and a maximum of 100 pages (50 sheets) for an additional $0.99 per page. Why can't I add another photo, and why does it tell me I have too many pages?
    It also won't let me move the photo I want to add into the "unplaced photos" area. You would think it would so I could at least substitute it for an existing one. Very frustrating.
    I have the latest iPhoto 6 and am using OS 10.3.9. (Panther).
    Any suggestions?
    Thanks.

    papple:
    Welcome to the Apple Discussions. The maximum number of pages is 50. That would be 50 double-sided or single sided. Do you have any unused pages at the end that would be causing that warning? Contron-click on a page outside of any picture and select the option "Clean up book". That will automatically remove any empty pages and (warning) remove any empty frames for a partially finished page and change the layout, i.e. remove an empty frame from a 3/page and change it to 2/page. So don't run this if you have any partially finished pages. You can duplicate the book and then run tests on the duplicate copy.
    Are you sure you selected double-sided or it did not get unselected somehow?
    Do you Twango?
    TIP: For insurance against the iPhoto database corruption that many users have experienced I recommend making a backup copy of the Library6.iPhoto database file and keep it current. If problems crop up where iPhoto suddenly can't see any photos or thinks there are no photos in the library, replacing the working Library6.iPhoto file with the backup will often get the library back. By keeping it current I mean backup after each import and/or any serious editing or work on books, slideshows, calendars, cards, etc. That insures that if a problem pops up and you do need to replace the database file, you'll retain all those efforts. It doesn't take long to make the backup and it's good insurance.

Maybe you are looking for