Win 8 is unsupported on late 2013

Hi,
For some reason when I run Bootcamp to install Winodws 8 it comes up with a message that says its not supported. I have a Late 2013 iMac 27" which by all acounts is supposed to be supported. Does anyone know how to overcome this? My About info is:-
Hardware Overview:
Model Name:          iMac
Model Identifier:          iMac14,2
Processor Name:          Intel Core i7
Processor Speed:          3.5 GHz
Number of Processors:          1
Total Number of Cores:          4
L2 Cache (per Core):          256 KB
L3 Cache:          8 MB
Memory:          8 GB
Boot ROM Version:          IM142.0118.B00
SMC Version (system):          2.15f2
Serial Number (system):          DGKLJ2JBF8JC
Hardware UUID:          2284E0DB-42FB-529B-86D2-FD3A57EE3683
I can't get past Bootcamp to install it, if I ignore the message and try it then runs Bootcamp and can't find a disc drive to install Windows 8 on due to a GPT error?
I have the iMac 27" 1Tb Fusion Drive.
I have read loads of info on this GPT error but seems to only be a problem for 3Tb hard drives, mines only 1Tb so i'm not sure whats wrong.
Lee

That's a bit odd. Maybe keep trying. There have been one or two problems downloading support drivers but usually with a different error message.
You could try phoning Apple Support.
Good luck

Similar Messages

Cannot install Win 8 on a late 2013 iMac using bootcamp on 10.9

I'm trying to install Win 8 on a late 2013 iMac (purchased a couple of months ago)
I have a win 8 pro DVD, but obviously there is no DVD in this iMac. I usally use the DVD drive in my older 2009 iMac for any disk based installs but I can't appear to use it here.
I followed the instructions and downloaded a Win 8 Pro ISO from Microsoft to use with my authentication code, created a bootable USB using bootcamp, created the partition and rebooted. Once I'd entered the code I get to the install location but it says I cannot install on the partition created by bootcamp. Even if I format the partition it says I need a GPT drive but I have MBR, so won't let me install.
I tried several suggestions including creating aprtitions in various other programs and once I even got past that screen, but as soon as it tried to install I got another error saying the MBR was formatted incorrectly and it failed.
I had no issues installing Win 7 via bootcamp on the older iMac, but this one has me stumped. I used to think I knew a bit about computers, but I'm fairly new to Mac related issues as the older iMac has always just worked.
Any help would be greatly appreciated.

Hello,
I just installed Windows 8.1 on my Late 2013.
There are just a couple of things I had to do that deviated from the Boot Camp Installation Manual.
1. I downloaded my copy of Windows 8.1 as an ISO image AND as a bootable USB from the Microsoft site.
Not sure why I did that but it came in handy because Bootcamp was taking a very long time to copy the ISO onto the USB stick..
The ISO copying seemed to freeze up, but it's likely that it was just taking a long time, probably 20mins.
So, instead of waiting, I took the contents of the the USB startup stick and simply moved them over to the stick that Bootcamp had formatted for the ISO copy (I cancelled that copy function and deleted any files that had copied but didnt complete).
Once that was done, the machine rebooted from the USB stick and began the normal Windows setup process.
All went very smoothly except that my mouse was not working.
2. To get around the mouse issue, I simply plugged in a MS USB Mouse and it worked immediately.
The Bootcamp manual advised that the way around this was to 'click in upper right corner and search for Bootcamp'. Problem was, it was nowhere to be found.
So, using my MS mouse, I navigated to the 'DESKTOP' icon in Win 8.1 and found File Explorer, which showed my USB stick connected along with Bootcamp and the MS Support File (i.e. All the Apple Drivers).
I began manually clicking on all the driver files until realizing that there IS a Bootcamp executable which will automatically install the drivers for the Nvidia card, keyboard, camera, mouse, etc....
Once that was done, my installation was completed.
The entire process took about an hour, but now that I've done it, it really shouldnt take much more than 45 mins.
I have the late 2013 iMAC, with the GTX780M and 1TB Fusion Drive i5 Quad Core.
For those who are leery about doing this, please note that I'm a PC 'lifer' and this is my very first go-around with doing anything on an Apple product.
It all went much more smoothly than I could have imagined, but if you are not a PC person, you might be a little challenged finding the Bootcamp in File Explorer or doing anything in Win 8.1 to get over these minor hurdles.
Good luck!
I'm looking forward to getting STEAM up and running to see how this thing games!

Late 2013 MBP "Boot Camp x64 is unsupported on this computer model"

Hey yall, some help would be fantastic.
Got my brand new Late 2013 MBP (top end model with the Nvidia GeForce GT 750M) on Thursday and had no problems getting it set up. Having gotten the OSX side all set up, last night I Bootcamped it. The new Bootcamp Assistant did a great job of loading my Windows 7 ISO onto one Flash drive and Bootcamp Assistant 5.0.5433 on the other Flash drive.
Had no problems during installation but the Bootcamp Support Tools didn't install, so I went to install it (attempted to run the setup file) and received this error:
Uh oh.
Using the internet (on my iPad) I was able to learn of a workaround to call the installation by negotiating to "Bootcamp\Drivers\Apple\" and executing the Bootcamp.msi as admin. It appeared to install everything.
However, when I went to change the resolution, I noticed that Windows was using a generic driver and that my max resolution was 1600x1200.
If I could launch a game w/out it immediately crashing, I would have chalked it up to Windows being Windows, but they did and I started digging (assuming that it was an application issue). Tried installing drivers downloaded from Nvidia's website for the 750M but they failed to find applicable hardware. Now concerned, I validated that I had received the correct version of MBP.
Eventually used a tool from M$'s website to remove the Bootcamp Support Software and then downloaded Bootcamp Support Software version 5.0.5033, where I ran into the exact same issue. Perhaps related, perhaps not, but the wireless on the Windows side takes a long time to connect and appears unreliable/periodically slow. That suggests that the wireless drivers weren't installed correctly either.
I have no problem reinstalling Windows, but I'm not convinced that its the problem. The initial error message suggests to me that the Bootcamp Support Software isn't recognizing my MBP. Any thoughts?
Thanks!

Hi,
it took me finally 4 days to setup Windows 7 via bootcamp. The drivers that are downloaded via bootcamp do not work when installing from a flash drive. Here is what I did to fix the issue with "CD/DVD driver missing...." which would show right after you select the language during installation.
While in OS X, go to the intel website and download the the driver for USB 3.0. Place the file on your windows partition. Boot again, hold the option key and select your flash drive which has the Windows 7 installer on it. Once you get the error message, click browse and locate the driver on your windows partition. Once installed, Windows 7 installs without any problems.

Problem installing Windows 7 64-bit on late 2013 iMac 27"

Is Windows 7 64-bit compatible with this computer?
Hardware and software:
• Late 2013 iMac 27", 3.5 GHz I7, 16 GB memory, 1 TB hard drive (no fusion drive)
• Mac OS 10.9.1
• USB thumb drive
• Boot Camp Assistant 5.1.0
• Windows 7 64-bit install disk iso image downloaded from Microsoft
Install steps:
1. Use Boot Camp Assistant to install Windows 7 install (from iso image) and Apple Support Software (creates WININSTALL USB drive)
2. Use Boot Camp Assistant to create 50 GB Windows partition on iMac internal drive and start Windows install
3. Complete initial install steps until given option to select install partition
4. Select 50 GB partition. Error message that partition is not formatted correctly. Use Advance Options to format (presumably to NTFS)
5. Select 50 GB partition again and click "Next"
6. Get error message "Setup was unable to create a new system partition or locate an existing system partition. See the Setup log files for more information."
7. Install quits at this point
I have successfully installed Win 7 on another computer (2010 Mac Pro) using these steps. I also tried installation on the iMac using an iso image created from my original Win 7 64-bit install disk, with the same installation error as above.
I'm wondering if Windows 7 and/or Boot Camp is compatible with this iMac. Any suggestions will be appreciated.

I am awaiting delivery on the exact model you have and have been researching how much trouble it will be to put 64 bit windows 7 ultimate on my machine when it gets here. I'm not pleased at what I've been reading so far. I have not seen the two other posts but yours is enough to concern me.
Have you also seen that 10.9.1 update may be responsible for this? I've seen where 10.9 caused some problems with the bootcamp app but then the process was completely hosed with the 10.9.1 update. Are you seeing this as well?
Being a life-long mac dude, it pains me when their stuff just doesn't work because it usually just does. ****, that's why I started on a mac in the first place.
The support site says that they come with 90 days of complimentary support. Is this not an issue they should be responsible for addressing via support? Or is that just one long wait on hold waiting to talk to somebody that won't consider this a pure apple issue?
I was also curious if your install .iso contains both 32 and 64 bit versions?

How to get new Macbook Pro Retina (late 2013) to detect external monitor via HDMI?

Hi everyone, this is my first Mac and for the most part it's been really, really wonderful.
This is my first major glitch: I cannot get it to detect my external display: It is an ASUS PA248Q, manufactured Aug 2012.
The HDMI cable according to my Amazon history is at least 1.3c from 2010, "Fanatic Digital Imperial Series Gold-Plated HDMI Cable (6 feet)".
It works with perfectly connecting an AmazonTV box to an old Samsung TV, with vivid clarity, unlike our cableTV signal.
Just in case, I have a new HDMI cable on order, which claims to be of newest standards.
The Macbook Pro Retina (late 2013) has the standard Intel Iris from the Haswell chips, as well as Nvidia GT 750M, the latter which I don't think has been used yet.
The ASUS display says: HDMI NO SIGNAL.
I have tried shutting them down and replugging the cable. I don't know what the ideal order is. The Macbook Pro is plugged into AC power, as suggested.
In System Preferences>Display, I press the Option key to select "Detect Displays" option (seriously unintuitive).
I have also tried resetting the NVRAM:
I shut the machine down. Pressed the power button, then quickly held the quadruplet: Option-Command-P-R (a double handful) and waited for the machine to chime a 2nd time. Tried to detect external display no luck.
Next, I reset the SMC:
I shut the machine down. Then I pressed Shift-Control-Option-Power for about 5 to 10s. Then I turned on the machine normally.
NVRAM & SMC steps were from an old youtube video, as the instructions I had did not explain how to do so clearly.
Please let me know if I"m doing something wrong.
Seems so exorbitant to pay $350 for Apple Care; that's a the cost for a whole new cheap laptop.
I will search the forums again. If anyone answers this, thank so much!

Hello there, willr314.
It sounds like you've covered most of the practical steps found in this Knowledge Base article:
Apple computers: Troubleshooting issues with video on internal or external displays
http://support.apple.com/kb/ht1573#1
No video or no signal, image distortion, "snow," or flickering
Check connections
When using an external display be sure to check the following:
If you're using an Apple notebook, confirm the AC power cable or adapter is securely connected to the computer and the cable providing power to the display is also secure. It is always good to have your notebook connected to AC power when an external display is in use.
Confirm display adapters are fully seated in their respective connections and that they are supported models and for the computer and display. Refer to these articles to assist you with adapter compatibility and further configuration information:
Monitor and Display Adapter Table
About Mini DisplayPort to HDMI adapters
Apple Mini DisplayPort adapters: Frequently asked questions (FAQ)
Thunderbolt ports and displays: Frequently asked questions (FAQ)
Remove all display cable extenders, KVM switches, or other like devices and retest to determine if the issue is resolved.
Try unplugging the video adapter or cable and then plug it back in.
If more than one video adapter is in use (or "daisy-chained"), troubleshoot by using only one adapter.
Example: A mini DisplayPort to DVI adapter connected to a DVI to HDMI adapter is an unsupported configuration because there is a series of adapters in use.
If available, try using a different display and or adapter (or use a different connector by using DVI instead of VGA, for instance).
Reset the system
You can reset the Mac's parameter RAM and SMC.Reset the resolutionStart by resetting the Mac's parameter RAM. If the display does not come up, was previously set to an unsupported resolution, and still results in no video:
Start up in Safe Mode.
From the Apple () menu, choose System Preferences.
Choose Displays from the View menu to open the preferences pane.
Select any resolution and refresh rate that your display supports.
Restart your computer.
The article does offer some additional links and recommendations as well:
These articles may offer additional assistance and information about displays and video adapters:
Apple Portables: How to use your computer in closed lid mode with an external display
Apple Cinema Display (30-inch DVI) has 1280 x 800 as the maximum available resolution
Mac Pro (Early 2009), Mac Pro (Mid 2010): Supported display configurations
For assistance with Retina displays, please see Frequently asked questions about using a Retina display.
If you tried all of these steps for your display and the video issues persist, contact Apple technical support or take your Apple computer to the nearest Apple Store or Apple Authorized Service Provider (AASP) for diagnosis. If you plan to visit an Apple Retail Store, make a reservation at the Genius Bar using http://www.apple.com/retail/geniusbar/ (available in some countries only).
Note: Diagnostic fees may apply for issues not covered under warranty or the AppleCare Protection Plan (APP).
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

Why do USB drives plugged into USB hubs make my Mac Book Pro (Retina late 2013) wake from sleep?

I have 2 x USB hubs, a Logitech USB 2.0 hub and a Broway USB 3.0 hub. Tested both and both seem to be the cause of my late 2013 Mac Book Pro waking from sleep. I ran syslog to find out why (syslog |grep -i "Wake reason") and the reason I got back was "kernel[0] <Notice>: Wake reason: XHC1" - this means nothing to me, but it didn't take too much mucking about to hunt the problem down and figure out it was the USB hub with any USB drive attached. If the drive is attached directly to the computer. No problem, computer sleeps fine.
This was a problem I encountered (and never solved) with OSX 10.6.8, a 2008 Macbook Pro the same Logitech USB 2.0 hub, but with different drives. I put the problem down to a bug that never got solved in an old system. But I am simply AMAZED after my update to a new MBP and new system that it is still about almost 6 years, a dozen MBP's and 4 systems later.
The other problem is that not only does the USB drive/ USB hub combo wake the computer it also loses the drive upon sleep and mounts it again upon wake. Then repeats this process every couple of minutes. And it obviously doesn't eject the drives properly because each time I return to the computer after I put it to sleep or let it go to sleep I get a giant list of "Disk Not Ejected Properly" notifications about it. Which I'm guessing could eventually cause some file damage.
I've tried combinations of different drives, different hubs (a Belkin and a no-name Chinese brand 2.0 hub) and the problem persists. Is there a solve to this problem? I'm surprised to see so little posts on forums about this. Am I just unlucky and got another combination of faulty/problematic hardware, or is this a real problem that exists for everyone? If not I would love to know if people have found winning combos of USB hubs and drives. But if it is, then it HAS to be solved.
If you have a Macbook Pro, then you are limited to 2 USB outlets, this is obviously a bare minimum and I would say that 95% of people using their laptop computer in the office or at home have a hub, and very likely a USB drive attached to it. I know actual Apple reps don't really pay much attention to the community support posts, but I've got 6 months worth of Applecare left and would like suggestions about how to get Apple's attention about this problem.
BTW Jettison (a 3rd party app that ejects drives properly before sleep) is not a solve. It is a 3rd party app that tries to fill a hole in a broken system. I don't want to eject my drive upon sleep, I want it to got the **** to sleep.

Is there a pattern to the time of day or other detail that may be
traced back to a OS X system cause of this odd phenomenon?
Are there any copies of system files on any of the attached USB
external drives? Any libraries, such as iTunes, iPhoto, etc?
Once the drives are indexed by Spotlight, are their permissions
ignored by the OS X? Content, if neutral, should not affect the
wake or sleep cycle; especially if they're ignored by the OS X.
Could there be a bad cable or other component? If so that would
be a difficult process of elimination to detect it. Usually replacing
most suspect components in the USB stream (external to Macs)
is a rote way to mechanically test that idea; & not 100% sure.
Does the equipment all have a good ground to the utility or house
electrical field? An intermittent ground may affect more than sleep.
Hard to say at this point. Maybe a late-night talk radio guru on
remote viewing could peer into your situation and sleuth it out?
Sorry to have run out of ideas, but the process must be electrical
& mechanical to some extent. - Or perhaps odd software inspired.
Do you have any phone-home spyware items inside, just jumping
at the chance to spill your information? Little Snitch may help.
PS: Perhaps the computer needs to go into Apple & have a genius
or product specialist at AASP test the unit thoroughly... BlueTooth?
see:
https://www.google.com/?gws_rd=ssl#q=Wake+reason:+XHC1
Good luck & happy computing!
edited 2x

Installing Windows 7 on Late 2013 iMac w/ Fusion Drive

Sorry in advance for the long post, but I have tried to exhaust all possibilities, and bring as much knowledge about our environment to the table to avoid confusion.
Here's our goal: Install Mac & Windows on a Late 2013 iMac with a 1TB Fusion Drive
Install our Mac Image with Deepfreeze on Partition 1
Install our Windows 7 x64 Image with DeepFreeze on Partition 2
Here's why our goal cannot work out of the box:
Deepfreeze for Mac, is not supported on a Fusion Drive. Now before anyone says "just don't use deepfreeze"...we are using it, and that is that.
In order to get our existing image to work on the iMac, we had to split the Fusion Drive.
Splitting Up the Fusion Drive
We booted into Recovery, Opened up terminal, retrieved the LvGUID, deleted it, and split up the SSD from the HD.
So now, we have a 128GB SSD, and 1TB HD showing up under Diskutilitiy.
We then partitioned the 1TB HD, into two, 500GB Partitions. One for Mac OSX 10.9.4, and the other for Windows.
The 128GB SSD is going to be used for scratch space, temp, etc. And is irrelevant at this time.
Deploying our Mac Image
After splitting the Fusion Drive, we netbooted and installed a "NetRestore" of our image. Worked completely fine, no issues. DeepFreeze Works fine, the 128GB SSD shows up just fine, and the other 500GB Windows Partition shows up fine. All drives / partitions can be written to with no problem.
Deploying our Windows Image
Deployed our Windows Partition image as we have done in the past, by booting into a windows PE Disk. (We have other various 2009, 2010, and 2011 iMacs across campus, with NO FUSION DRIVES installed, and dual boot them successfully using the same procedure. Minus the splitting of the fusion drive part of course) After the Windows image is deployed to the windows partition, we then boot it up to a Windows 7 Install disk to fix the MBR, Bootrec, and BCD options to allow it to boot properly. Here's where we run into issues: Upon getting the Windows 7 Install screen, the USB Keyboard and Mouse, DO NOT WORK.
Here's the options we've tried to get them to work properly
1. Tried another known working Mac USB Keyboard & Mouse = Failed
2. Tried a known working Windows Keyboard & Mouse = Failed
3. Plugged Just a known working Mac Keyboard into each USB Port to see if recognized = Failed
4. Plugged Just a known working Windows Keyboard into each USB Port to see if recognized = Failed
5. Plugged Just a known working Mac Mouse into each USB Port to see if recognized = Failed
6. Plugged Just a known working Windows Mouse into each USB Port to see if recognized = Failed
7. A Windows 8.1 Recovery USB will boot and the USB Mouse & Keyboard are recognized and installed! (YAY!!) However, we cannot repair a Windows 7 install with Windows 8.1..
BootCamp Drivers & Support Media
Downloaded the Current BootCamp Support drivers to enable the USB and other various drivers to be loaded during setup (Placed the $WinPEDriver$ and AutoUnattend.xml, and BootCamp folder on the Root of a USB, and modified a Windows7 Installation disk and placed on the root as well) The drivers do not load. Have also placed on a brand new USB2, and USB3 flash drive formatted at FAT32, to see if that made a difference, which it did not. The BootCamp USB made within Mac, it loads saying "Now booting into Boot Camp Assistant Created USB Drive..." or something like that (Don't remember the exact Message)
Side Note:
Restored Fusion Drive to its original State, and booted from the BootCamp USB drive, still no usb Mouse & Keyboard Support.

I have same issue
Tried everything differend hdd,ssd as well
Basically when trying instal win 7 via iOS maverick when reboting and windows booting to the first scree everything freezing cant do much.
Also tried install clear ssd without any system, but soon after format ssd or hdd I have error that I cant use this disk to install windows!!!!!!!!!!!!!!!!!
What is funny Windows 8 installing without any problem!!!
what is going on APPLE??wher is support
This issue I have only on Late 2013 on my other Late 2012 this issue not exist and everything working as should.

Installing windows 7 on mac book pro late 2013

Installing Windows 7 on Mac Book Pro Late 2013
Background
Mac Book Pro Late 2013 uses a USB 3.0 hub for the external ports, the keyboard and mouse devices.
Windows 7 does not have the drivers to support USB 3.0 ports so these must be integrated into the boot.wim and install.win files so that Win7 can be installed and used on a Mac. If these drivers are not integrated when win7 is booted up then the mouse and keyboard will not function.
Requirements:
Two USB Flash drives
Access to a Mac computer
Bootcamp Assistant application
Access to a Windows computer with windows 7 installed
Windows 7 install disk or ISO file
WinUSB application
Windows Automated Installation Kit for Windows 7 (WAIK)
Method
On a Mac
First prepare a USB Flash drive by formatting it using disk util app, found in Application Utility folder, to FAT format this will store the Apple drivers that can be downloaded from Apple using BootCamp.
This will be called USB1
Using Boot Camp Assistant select 'Download the latest windows support software from Apple' to get the files from apple for win7 for your particular machine these will be downloaded and copied to the USB Flash drive called USB1.
On a PC
Using a PC download a copy of WinUSB from www.joshcellsoftwares.com this software can create a bootable USB with the win 7 files copied on to it.
Obtain a copy of Windows 7 either in DVD or ISO format.
Using WinUSB and the Win7 DVD create a second bootable USB Flash drive. This will be called USB 2.
About DISM
DISM is a windows application that allows the editing of windows image files with the extension of WIM.
If DISM is not installed on the PC it can be downloaded from windows website.
To test to see if DISM is installed, open up a command prompt. Then type 'dism' without the quotes this will display the help description of DISM.
Drivers
The apple drivers need to be added to the boot.wim file so that mouse and keyboard can function during the setup phase.
The apple drivers need to be added to the install.wim so that mouse and keyboard can function after the setup phase.
The video drivers are also added as it appears to cause problems if they are not included.
Create a directory structure like this:
c:\appleboot\
drvrs
mount
win7x64install
win7x64boot
Create the following files in c:\appleboot\ with the following code:
adddrivers.cmd
color 0a
dism /image:c:\appleboot\mount /add-driver /driver:c:\appleboot\drvrs /recurse
================================================================================ ==========
mountboot.wim.cmd
color 0a
dism /mount-wim /wimfile:c:\appleboot\boot.wim /index:2 /mountdir:c:\appleboot\mount
================================================================================ ==========
mountinstall.wim.cmd
color 0a
dism /mount-wim /wimfile:c:\appleboot\install.wim /index:4 /mountdir:c:\appleboot\mount
================================================================================ ==========
unmountcommitfiles.cmd
color 0a
dism /unmount-wim /mountdir:c:\appleboot\mount /commit
================================================================================ ==========
Copy the following files into their respective directories:
Copy from USB 1 into drvrs the $WinPEDriver$ directory
Copy from USB 2 \sources\boot.wim to win7x64boot directory, this will store the original file
Copy from USB 2 \sources\install.wim to win7x64install directory, this will store the original file
Then copy boot.wim from win7x64boot directory to the c:\appleboot\ directory
Then copy install.wim from win7x64install directory to the c:\appleboot\ directory
Once all the copying is completed then run the following cmd files in this order:
For boot.wim
mountboot.wim.cmd - this will mount the file for adding of drivers
adddrivers.cmd - this will add the apple drivers to the mounted boot.wim
unmountcommitfiles.cmd – this will commit the changes and unmount the boot.wim
For install.wim
mountinstall.wim.cmd- this will mount the file for adding of drivers
adddrivers.cmd - this will add the apple drivers to the mounted install.wim
unmountcommitfiles.cmd – this will commit the changes and unmount the install.wim
Copy the files back to USB 2
Copy the boot.wim and install.wim files from c:\appleboot\ directory to USB 2 sources directory and overwrite the files.
BOOTABLE USB
You will now have a bootable USB Flash Drive that has the additional drivers needed to install Win7 on Mac Book Pro Late 2013.
Mac Preparation
On your Mac using Disk Util reduce the size of the partition of Macintosh HD so that there is approx. 80GB free for the use of Win7.
Add a second partition, label it win7 and format it to FAT. This is so that win 7 setup can identify the correct partition.
Installing Windows 7
Insert USB 2 into your Mac and reboot, whilst holding the option key down.
After reboot there will be three icons displayed one is the Mac operating system, the second is the recovery partition and the third is an orange icon indicating a bootable USB drive.
Select this and win7 setup application will proceed to boot up with the keyboard and mouse functioning.
Follow the prompts and when the drive selection appears select the win7 partition and format it to NTFS so that win7 can be installed. When windows setup reboots press and hold down the option key and select the windows partition so that setup can continue to install.
After completion of installation of win7 insert USB 1 with the additional apple drivers. Goto the bootcamp directory and click on setup.exe file this will install additional drivers needed to use Win7 on a Mac.
Once completed reboot your Mac and select windows to allow the drivers to update in windows.

Yes this is correct that the /index:4 refers to the ultimate version of windows in mountinstall.wim.cmd
dism /mount-wim /wimfile:c:\appleboot\install.wim /index:4 /mountdir:c:\appleboot\mount
Users should do what applekryzzle suggested if you have a different version of windows. Thanks for the tip applekryzzle.
With regards to the Intel(R) USB 3.0 eXtensible Host Controller drivers they are the ones that are provided by apple via boot camp assistant.
These appear to work correctly and downloading as per instructions simplifies the procedure.
For those that are interesred the updated drivers can be found here https://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=22824&ProdId=346 7&lang=eng&OSVersion=Windows%207%20%20*&DownloadType=Drivers
I have also seen in other discussions that some users get black screens i believe that it is the lack of video drivers which is included in the download from apple using boot camp assistant.
I'm certain that this works on Mac Book Pro Late 2013 models and i feel confident that this will work with other models.
I will appreciate any feedback if this works on other models.

Is it possible to install windows 8.1 on macbook pro late 2013?

hi ,
Is it possible to install windows 8.1 on late 2013 macbook pro?
I have tried installing it twice but both of the time i got an error
Windows could not update the computer's boot configuration. Installation cannot proceed.

Maybe people have found a solution already but yesterday I managed to install Win 8.1 as a BootCamp on my new 15" retina MBP. I followed the steps John Guo described but with a couple of changes as his approach failed for me.
1. Make sure you are starting from a single partition.
2. Create the Windows install USB from the ISO and also allow BootCamp Assistant to create download the drivers - but untick the option to install windows.
3. Open Disk Utility and create a new partition and format as MS-DOS (FAT) rather than leave as free space.
4. Restart your Mac and use the option to boot into the Windows part of the USB not the EFI-boot.
5. Follow the install
6. When it comes to the drive selection select the FAT drive. Windows installer will say it cannot install here as it needs to be and NTFS partitiion (in previous atempts I always got the message to say the partitiion was using GUI partition table so could not install even though it was formatted to NTFS).
7. The format to NTFS should work fine and install proceed.
8. When the installer reboots the machine you will need to use the boot option to ensure you boot back into Windows.
9. Once installed the bootcamp driver install runs automatically and for me all drivers run fine even the NVIDIA, which I've seen some people mention having issues with.
I was inpressed with Windows automatically scaling the text to 200%, which meant it was using the full 2880x1800 resolution so everything was crisp but the windows and text was scaled nicely. I changed this 150% to give me some more real estate.
I'm guessing that by formatting the new partition as FAT it creates a MBP within the new drive that is writable by windows but I'm not a windows guru so this is a guess. But anyway, this work perfectly.
hope this helps some people.

Cannot install Windows 8.1 on Late 2013 iMac

Attempting to install Windows 8.1 (retail) using Boot Camp Assistant but when I get to the "Select disk to install windows" screen, nothing appears.
I'm using a retail copy of the Windows 8.1 full installer DVD and I have the midrange 21.5" late-2013 iMac.

Installed my retail copy of Windows 8.1 from Windows 7 without any hiccups or hacks. Windows 7 can be installed in trial mode for free and easily by downloading a legal ISO from Digital River. Create a USB installation with Boot Camp Assistant and proceed as normal using the Windows 7 ISO. During Installtion, skip entering a license. After Windows 7 is successfuly installed, boot back into OSX and create just a drivers USB using Boot Camp Assistant. Boot back into Windows, insert your retail Windows 8.1 disc or use your download and let it install. Be prepared to do several "Hold-Option" boots to kick it into windows. Installation probably had 6 reboots.
Digital River ISOs
Windows 7 Home Premium 32Bit:
http://msft.digitalrivercontent.net/win/X17-58996.iso
Windows 7 Home Premium 64Bit:
http://msft.digitalrivercontent.net/win/X17-58997.iso
Windows 7 Professional 32Bit:
http://msft.digitalrivercontent.net/win/X17-59183.iso
Windows 7 Professional 64Bit:
http://msft.digitalrivercontent.net/win/X17-59186.iso
Windows 7 Ultimate 32Bit:
http://msft.digitalrivercontent.net/win/X17-59463.iso
Windows 7 Ultimate 64Bit:
http://msft.digitalrivercontent.net/win/X17-59465.iso
Thanks, and I hope this helps whoever needs it. I always hate when someone finds a fix and never reports back.

Installing windows 8.1 on new mac pro (late 2013)

Greetings,
First time poster so forgive me if I mess up protocol.
I'm trying to install Window 8.1 on my new late 2013 Mac Pro via bootcamp.
I have followed all the steps in bootcamp and the installation fails saying "cannot update boot configuration".
I tried using a few methods I saw people on here had success with creating their own partitions with disk utility, but I still have not had success.
My system is the 6 core version, 16gb RAM, 512gb flash storage, D500 graphics cards
Any help would be greatly appreciated.

I have the same problem with my brand new MacPro (6-Core, D700, 1tb SSD)
I have called Apple support to report this issue, in the mean time I've done the following tests:
Windows 7/8 tests NO Joy...
I have also tried tricking the windows 8 installer by doing the following.
1)Boot of Windows 8 installation (USB)
2)At the setup screen it will ask you to format your boot camp created drive to NTFS so that windows can be installed.
After the formatting is done and windows is ready to install i swap the Windows 8 USB stick for a Windows 7 USB stick then I click on next.
3)Windows starts copying the files just like it did on the Windows 8 installation and I get the same error.
"Can't update boot configuration"
I guess it has nothing to do with the Windows USB Stick since I've tried installing Win 7/8 and 8.1 with the exact same error.
I have not received any news from Apple support on this issue.
Any other ideas or suggestions ?
Thanks!

Can I install Windows 7 (64 bit) on late 2013 edition of MacBook Pro?

Can I install Windows 7 (64 bit) on late 2013 edition of MacBook Pro using Bootcamp? Before today, I would have never even asked this question due to the large number of users who continue to use Windows 7 in the PC world! However, there seems to be two conflicting links on the Apple site.
http://support.apple.com/kb/ht3986
http://support.apple.com/kb/HT5634
From the first link, there is a statement as follows: Mac Pro (Late 2013) only supports Windows 8 (64-bit).
From the second link, the table (under MacBook Pro) clearly states that the Retina, 13 inch, late 2013 edition supports BOTH Windows 8 64 bit and Windows 7 64 bit.
So the above information is conflicting; and as a result, I am confused! Thanks for any responses.

As far as I am aware your computer supports Win 7 and Win 8 - 64-bit.
Windows on Intel Macs
There are presently several alternatives for running Windows on Intel Macs.
   1. Install the Apple Boot Camp software. Purchase Windows 7
         or Windows 8. For Boot Camp 4.0 and above you can only use
         Windows 7 or later. Follow instructions in the Boot Camp documentation on
         installation of Boot Camp, creating Driver CD, and
         installing Windows. Boot Camp enables you to boot the
         computer into OS X or Windows.
     2. Parallels Desktop for Mac and Windows XP, Vista Business,
         Vista Ultimate, or Windows 7. Parallels is software
         virtualization that enables running Windows concurrently
         with OS X.
     3. VM Fusion and Windows XP, Vista Business, Vista Ultimate,
         or Windows 7. VM Fusion is software virtualization that
         enables running Windows concurrently with OS X.
     4. CrossOver which enables running many Windows
         applications without having to install Windows. The
         Windows applications can run concurrently with OS X.
     5. VirtualBox is an Open Source freeware virtual machine such
         as VM Fusion and Parallels that was developed by Solaris.
         It is not as fully developed for the Mac as Parallels and VM
         Fusion.
Note that VirtualBox, Parallels, and VM Fusion can also run other operating systems such as Linux, Unix, OS/2, Solaris, etc. There are performance differences between dual-boot systems and virtualization. The latter tend to be a little slower (not much) and do not provide the video performance of the dual-boot system. See MacTech Labs- Virtualization Benchmarks, January 2013 | MacTech for comparisons of Boot Camp, Parallels, and VM Fusion. Benchmarks of all of the above except Crossover can be found in Benchmarking Parallels, Fusion, and VirtualBox Against Boot Camp - The Mac Observer. Boot Camp is only available with Leopard or later. Except for Crossover and a couple of similar alternatives like DarWine you must have a valid installer disc for Windows.
You must also have an internal optical drive for installing Windows. Windows cannot be installed from an external optical drive.

GPT partition inhibiting windows 8.1 install on MBP retina late 2013

Hi there, looking for some help!
Trying to install win 8.1 on my MPB retina late 2013 using bootcamp.
Bootcamp makes the partition but then the windows installer does not automatically start (Bootcamp help says it should.. Original full windows disk is in superdrive).
Restarting pressing "option/alt" gives me the choice to start "windows".
This starts the windwows installer.
Seems fine untill I need to select a disk to install windows onto.
Choosing "Drive 0 Partition 4: BOOTCAMP" Does not work.
it says "windows cannot be installed on drive 0 partition 4"
Same after pressing "Format"
Details show:
"Windows cannot be installed to this disk. The selected disk is of the GPT partition style"
I saw a solution to a problem like this:
https://discussions.apple.com/message/23545484#23545484
But I expect that this would not be nessecary anaymore.
Windows 8.1 is supposed te be supported by Bootcamp nowadays.
My Bootcamp is:
Boot Camp Assistant 5.1.1, Copyright © 2013 Apple Inc. All rights reserved
Software update says no updates are available for my machine.
Anyone?

delete partition bootcamp created in windows installer
and let windows installer create new one (it will create 4)
after that, IF installer won't to able to write on partition created, reset pram http://support.apple.com/kb/ht1379 start installer again by booting with ALT + Option
it will be able to write to the partition it created

Please help on installing windows 7 on late 2013 imac 27"!!!

I am using imac 27" late 2013. I tried installing windows 7 64bit using boot camp assistant and it went well. I also download the latest bootcamp 5.
However i cant install bootcamp on the new windows 7. Anyone have the same problem?

I have same issue
Tried everything differend hdd,ssd as well
Basically when trying instal win 7 via iOS maverick when reboting and windows booting to the first scree everything freezing cant do much.
Also tried install clear ssd without any system, but soon after format ssd or hdd I have error that I cant use this disk to install windows!!!!!!!!!!!!!!!!!
What is funny Windows 8 installing without any problem!!!
what is going on APPLE??wher is support
This issue I have only on Late 2013 on my other Late 2012 this issue not exist and everything working as should.

MBP late 2013 i7 2.3gHZ restart problems and major input lags

Since I've updated my MBP i7 2.3 Ghz late 2013 to OSX Yosemite (10.10.1) I can't restart the macbook with my promise harddrive and apple cinema display still connected via thunderbolt. When I restart it keeps hanging on the grey screen without the apple logo. When I unplug the thunderbolt and usb cable, hold down the power button and turn it back it everything is fine. Just the restart won't work.. Any ideas?
Further more, I receive major input lags in different programs. For example I use Final Cut Pro (10.1.3) a lot for my job. I use managed media library all stored on the promise harddrive via thunderbolt. The footage I use is raw of the SD card from a Nikon D800 (h2.64 mov), of course i let everything import first before editing. Though I get major input lags (0,5-1,5 sec) when pressing the spacebar to play for example. Ive used this workflow exactly the same on my previous MBP (17" late 2011 I think) without any lags.
Specs of my MBP:
MacBook Pro (Retina, 15-inch, Late 2013)
Processor 2,3 GHz Intel Core i7
Memory 16 GB 1600 MHz DDR3
Graphics NVIDIA GeForce GT 750M 2048 MB
Storage 512 GB SSD
Hope anyone can help me.

Your original configuration is an HDD. Have you considered replacing it with an SSD. It helps quite a bit.
The current 2013 (and now the 2014) MBPs are excellent machines, and can run Bootcamp via native EFI (Win 8/8.1 - Win7 has some driver challenges), rather than the CSM-BIOS layer and you will get very good performance. I would recommend a 16GB MBP. If you do a lot of external display work, dual GPUs may work better for you.
I use the TB-to-FW for accessing external disks, not sound cards, but the storage works fine. This machine can support 8GB RAM, which may also be worth considering.

Win 8 is unsupported on late 2013

Similar Messages

Maybe you are looking for