Without 'MLS QOS' in 6500 does any interface queueing and trusting take place?
I have a 6500 that does not have 'mls qos' global configured, although the interfaces do have 'mls qos trust dscp' on them as in:
interface GigabitEthernet3/3
switchport
switchport access vlan 536
switchport mode access
switchport voice vlan 910
logging event link-status
mls qos trust dscp
spanning-tree portfast
When I 'show queueing int gx/x', it does show the default queueing structure of the interface as in:
LLT-6509AS-A#sh queueing int g3/3
Interface GigabitEthernet3/3 queueing strategy: Weighted Round-Robin
QoS is disabled globally
Port is untrusted
Extend trust state: not trusted [COS = 0]
Default COS is 0
Queueing Mode In Tx direction: mode-cos
Transmit queues [type = 1p3q8t]:
Queue Id Scheduling Num of thresholds
01 WRR 08
02 WRR 08
03 WRR 08
04 Priority 01
---- snip ----
queue thresh cos-map
1 1 0 1 2 3 4 5 6 7
1 2
1 3
1 4
1 5
1 6
1 7
1 8
Packets dropped on Transmit:
BPDU packets: 0
queue dropped [cos-map]
1 0 [0 1 2 3 4 5 6 7 ]
2 0 []
3 0 []
4 0 []
Packets dropped on Receive:
BPDU packets: 0
queue dropped [cos-map]
1 0 [0 1 2 3 4 5 6 7 ]
So just what does the global 'mls qos' do? Without it is the command 'mls qos trust dscp' ignored?
I'm trying to track down where in our network dscp settings are being stripped out of packets and this is when I noticed the 'mls qos' was not configured.
it enables QOS on the switch, without it no QOS is being used.
Sent from Cisco Technical Support iPhone App
Similar Messages
-
How does Avilability check and TOR takes place in SD
How does Avilability check and TOR takes place in SD? if you have any Tax configuration notes please send it to my mail ID?
[email protected]
GopalATP
Types of Availability Check in Sales and Distribution
Processing
There are three types of availability check:
_ Check on the basis of the ATP quantities
_ Check against product allocation
_ Check against planning
The following SD-specific control features need to be maintained in Customizing:
_ Checking group
The checking group controls whether the system is to create individual or collective
requirements in sales and shipping processing. In addition, a material block for the
availability check with transfer of requirements can be set here. The checking group can
also be used to deactivate the availability check. This option was created especially for
the assembly order so that when the bill of material is exploded in the assembly order,
the individual components, if necessary, can be classified as non-critical parts as far as
procurement is concerned.
The checking group specifies in combination with the checking rule the scope of the
availability check. It is proposed in the material master record on the basis of the material
type and the plant, and copied into the sales and distribution documents.
_ Checking Rule
You use the checking rule to control the scope of the availability check for each
transaction in sales and distribution. You also specify whether the check should be
carried out including or excluding replenishment lead time. The individual checking rules
define by transaction, which stock and inward and outward movement of goods should
be taken into account for the availability check.
_ Schedule line category
You can control with the schedule line category whether an availability check and
transfer of requirements should be carried out in the sales documents. The possible
settings for this at schedule line level are dependent on the settings in the requirements
class which is determined from the requirements type of the material.
_ Delivery item category
The delivery item category can be used to control whether an availability check takes
place in deliveries.
Requirements type
The various requirements are identified by their requirements type. The requirements
type refers to the requirements class and its control features.
_ Requirements Class
The requirements class contains all control features for planning such as relevance for
planning, requirements planning strategy and requirements consumption strategy. In
addition, it is specified at a global level whether an availability check is to take place for
the material in the sales and distribution documents on the basis of the ATP quantity
(ATP = available to promise) and whether requirements are to be passed on. A finer
degree of control can be obtained for sales documents using the schedule line category.
Replenishment lead time is only included in the check performed on the basis of the
ATP quantity.
Prerequisites
An availability check can only be carried out if the following prerequisites have been fulfilled:
_ The control elements described above for the availability check must be maintained in
Customizing for Sales and the relevant assignments made to the sales transactions
_ The availability check must be switched on at requirements class level and - for the
availability check in the sales documents - at schedule line category level
A requirements type must exist by which the requirements class can be found
_ A plant must be defined. It can either be proposed from the customer or material master
record or can be entered manually in the document.
_ A checking group must be defined in the material master record on the Sales/plant data
screen in the Availability check field
Configuring entries of the Availability Check
IMGSDBasic fncsAvailability check and TORAvailability checkAvailability check with ATP logic or against planningDefine checking groups
You can use SAP std checking groups of 01 for summarized reqts or 02 for daily reqts or u can create ur own.
The columns total sales and total deliveries are selection options whereby u can configure a checking rule to sum up reqts to post to MRP either individually or by day or week.
Column 5, Block qty; set this block if u want several users to be able to process the material simultaneously in different transactions without blocking each other. The No Check indicator is used when u want a material to not be relevant for an ATP check.
Defining a material block for other users. The Block checkbox is an indicator that enables u to block the particular material from being checked for availability if it is already being checked at the same time by another user.
Defining the default value for checking groups. However should no entry exist for the checking group in the material master record, one can set a default value per material type and plant.
Controlling the availability check. In this section, u tell the system what stock on hand and what inward and outward movements of stock it must take into account when performing the availability check. These settings are based on the checking group that is assigned to the material master record and the checking rule that is predefined and assigned to the sd transaction. The carry out control for the availability check must be maintained for both the sales order and delivery.
TOR
IMG  SD  Basic fncs  Availability check and TOR  TOR
A line item in the sales order creates a schedule line. The schedule lines in the sales order transfer the requirements through to MRP. You can select the docs on which you want the TOR to happen. For ex, not for quotations.
The TOR aims to ensure the ordered materials are available for the requested delivery date. The TOR can be set for individual or for collective requirements (materials mastersales/plant view).
The TOR is dependent on the following data:
The reqts type, reqts class, checking group and schedule line category.
The reqts type and class are determined in the strategy group (material masterMRP3)
For TOR to be carried out, a few criteria need to be met:
Plant assigned to line item level, schedule line category should be switched on at TOR, TOR must be switched on at the reqts class level, checking group must be defined and allocated to the material master record (sales/plant view in the availability check field)
The reqts class is the controlling factor for the availability check and the TOR for all sd types.
Configuring the TOR:
1) Use std 041 reqts class or copy and rename it. Use the indicators to select if this reqts class must carry out an availability check and/or a TOR.
2) Define the reqts types. A reqts type is allocated to a single reqts class and not vice versa. It is based on the item category and the MRP type of the material.
3) Assign the rqts type to the relevant item category in the sales order and the MRP type found on the material master record.
You can select an alternative search strategy where u assign the reqts type to item category and MRP type. Can select source as 0, 1 or 2. (1 = Item type and MRP type strategy).
4) The TOR and Availability check can be selected/de-selected at the schedule line category level.
5) Block qty confirmation in delivery blocks. This is used to block the reservation of the TOR from MRP.
6) Maintain requirements for TOR. Requirements can be used to determine that the TOR to MRP is not carried out unless a number of conditions are met.
Availability Overview = CO09  order qty, sd doc no, item no, requirements class.
Stock requirements list = MD04  sd no or dly no, line item, schedule line placing the demand
Stock overview = MMBE  total stock per company, then plant followed by storage location, and finally a breakdown per batch
this is the customising as weel as the knowledge part.
PLease award pints if helpful
thanks -
How much space does MacBook Air OS and software take up?
Greetings,
I am looking to replace my aging 2008 MacBook with a new MacBook Air. I want to get the 11 inch model most likely with the 128GB of storage. I will use it mostly for email, web surfing and other light duty work.
While I don't intend to load it up with various software, I will probably put a half dozen peices of software on it, over and above the Apple software it comes with. But, no biggies like PhotoShop. My question is this:
About how much space does the Apple OS and the assorted Apple software that comes standard take up?
I cannot spend a lot and would like to avoid buying the bigger drive if possible.
Thanks.new from box it will have 121 GB available.
I cannot spend a lot and would like to avoid buying the bigger drive if possible.
Thats a bad working premise, no computer is a data storage device. You dont need a huge SSD, just an external HD for data backups and for putting tons of big media files on.
128GB is plenty for almost everyone, IF they know very very simple rules of drive management. -
The question about Firefox not printing directly from the Internet has been asked before-but no useful solutions have been offered. It came up in 2010 and was under discussion until Jan 30 when it was locked.. I would like to re open the issue to further discussion or be notified by Firefox that they cannot solve it.
call them, tell them you NEED a new battery installed, and they need to tell you when they can do it. That is their job to help you! Give pushback if necessary.
-
My old ID has this TV show I wanted to watch. But I wanted to transfer the show from that id to my new one which has most of my apps, music, and books. Does anyone have any advice for me?
You cannot.
Authorize your computer for both accounts. -
How long does erase all content and setting take
Hello,
Hi, i want to ask about "erase all content and setting", i have this ipad mini, and its already about an hour from the first time i choose that option, and till now there's nothing happened except this loading screen. Is it normal? Or do I have to connect it to my computer?
Thank you.Ohh, okay then, but the progress bar on my ipad hasn't appear yet, just that circle thingy going round and round again.
Do i have to let it be or there's something i could do about it?
thank you. -
How does the CRM to BW extraction takes place...????
Hi Experts,
i need a detailed explaination about crm-bw extraction. what are the steps followed & pre-requisites required. how it will be different from other extractions...???
cheers
swapsHi,
Pls chk this link; CRM
/people/swapna.gollakota/blog/2008/01/14/one-stage-stop-to-know-all-about-bw-extractors-part1
regarding bw crm extraction
Regards
Raj -
Mls qos trust cos vs mls qos cos in cat6k
Hello
I am trying to configure basic qos topology with two 6k connected to each other by the trunk port.
According to the documentation, if I set the mls qos cos value at the interface level I should modify the default cos on it, and all packets leaving incoming to this port, should be marked with the new cos value.
http://www.cisco.com/c/en/us/support/docs/switches/catalyst-6000-series-switches/24055-173.html
Unfortunately, when I set such config, all incoming packets transmitted through this interface was tagged with cos = 0 until I set the "mls qos trust cos" on the same interface.
Does anybody can explain to me this strange behavior?
I would like to mention that both 6k was connected to each other with ws-x6548-GE-TX modules.
Thank you in advance.
Ragards
LukasSarah
1) L2 switches can trust the dscp marking as well. The 2960 is a layer 2 only switch and the default is untrusted but if you then enter
"mls qos trusted" you have a choice of 'cos|dscp|ip-precedence'. The default if no choice is entered is DSCP.
2) If "mls qos trust dscp" is entered then the switch will use the DSCP marking found in the packet. This will then be used as the internal DSCP marking that all switches use. Unless you have a DSCP-DSCP mutation map the value used will be the value received in the packet.
Jon -
Good Morning, everyone. I am looking for some clarification with an existing 3750x Switch configuration.
I am reviewing the configuration of my network switches and found the following MLS QoS configuration on one of my switches and a partial of this same config on another switch. Can someone please explain what function, this line of code, is performing; and is it necessary?
mls qos map policed-dscp 0 14 24 30 38 to 8
mls qos map policed-dscp 10 to 12
mls qos map policed-dscp 12 to 14
mls qos map policed-dscp 26 to 28
mls qos map policed-dscp 28 to 30
mls qos map policed-dscp 32 to 34
mls qos map policed-dscp 34 to 36
mls qos map policed-dscp 36 to 38
mls qos map cos-dscp 0 8 16 24 34 46 48 56
mls qos srr-queue input bandwidth 70 30
mls qos srr-queue input threshold 1 80 90
mls qos srr-queue input threshold 2 80 90
mls qos srr-queue input priority-queue 2 bandwidth 30
mls qos srr-queue input dscp-map queue 1 threshold 2 16 24
mls qos srr-queue input dscp-map queue 1 threshold 3 48 56
mls qos srr-queue input dscp-map queue 2 threshold 1 36 38
mls qos srr-queue input dscp-map queue 2 threshold 2 32 34
mls qos srr-queue input dscp-map queue 2 threshold 3 40 46
mls qos srr-queue output cos-map queue 1 threshold 2 4
mls qos srr-queue output cos-map queue 1 threshold 3 5
mls qos srr-queue output cos-map queue 2 threshold 1 2
mls qos srr-queue output cos-map queue 2 threshold 2 3
mls qos srr-queue output cos-map queue 2 threshold 3 6 7
mls qos srr-queue output cos-map queue 3 threshold 3 0
mls qos srr-queue output cos-map queue 4 threshold 3 1
mls qos srr-queue output dscp-map queue 1 threshold 2 32 34
mls qos srr-queue output dscp-map queue 1 threshold 3 40 46
mls qos srr-queue output dscp-map queue 2 threshold 1 18 20 22 26 28 30
mls qos srr-queue output dscp-map queue 2 threshold 2 16 24
mls qos srr-queue output dscp-map queue 2 threshold 3 48 56
mls qos srr-queue output dscp-map queue 3 threshold 3 0
mls qos srr-queue output dscp-map queue 4 threshold 1 8
mls qos srr-queue output dscp-map queue 4 threshold 2 12 14
mls qos srr-queue output dscp-map queue 4 threshold 3 10
mls qos queue-set output 1 threshold 1 100 100 100 100
mls qos queue-set output 1 threshold 2 80 90 100 400
mls qos queue-set output 1 threshold 3 100 100 100 400
mls qos queue-set output 1 threshold 4 90 100 100 400
mls qos queue-set output 1 buffers 15 30 35 20
mls qos
If more information is required for a response, please let me know.
Thank you, E.Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
The function of each command is perhaps best explained by the Command Reference and Software Configuration Guide for your IOS version. If you have a question that's unanswered by those, please post another question. BTW, Cisco also publishes whitepapers that further explain some subjects. There are a couple on 3750 QoS.
Regarding whether a particular command is necessary would depend on what your QoS policy is attempting to accomplish. -
Catalyst 3550 & 3560/3750 command 'show mls qos interface statistics'
On the Catalyst 3550 the command 'show mls qos interface statistics' will show ingress packet (or byte) counts with DSCP values. If you have policers configured then it also shows a count of packets that have been marked down to another DSCP value due to policing or any that have been dropped (obviously 'mls qos monitor dscp x' needs configuring). The same command on the 3560/3750 only shows the ingress & egress DSCP values, there is no column that shows packets (or bytes) that have been policed or dropped. Is there any command to display the same information with the 3560/3750?
Neither platform show counters when the command 'show policy-map interface x/x' is used so this won't work.
Thanks
AndyHi, I believe there is a command on the 3560 'sh mls qos interface policers' may be what you are looking for.
Here is what the command says it outputs:
To display QoS information at the interface level. This information includes:
The configuration of the egress queues and the CoS3-to-egress-queue map
Which interfaces have configured policers
Ingress and egress statistics, which includes the number of bytes that have been dropped -
3750 - Show mls qos interface statistics
Hi All,
Sorry if this is posted in the wrong place but can anyone shed any light on the meaning of the five columns given in the output for the following command on a 3750 ?
Show Mls Qos Interface <interface id> Statistics
Many Thanks
ShaunI think that this is my first post, so I hope it will be useful ;-)
It's indeed very strange, I faced the same problem before, so I tried to check older switches, and I was able to find what these values are, for example, if You check the link :
Understanding QoS Policing and Marking on the Catalyst 3550
http://www.cisco.com/en/US/products/hw/switches/ps646/products_tech_note09186a00800feff5.shtml
You will find that these five fields mean:
incoming no_change classified policed dropped (in pkts)
This is a description of the fields in the example:
Incoming—shows how many packets arrive from each direction
NO_change—shows how many packets were trusted (such as QoS level not changed)
Classified—shows how many packets have been assigned this internal DSCP after classification
Policed—shows how many packets were marked down by policing; DSCP shown before markdown.
Dropped—shows how many packets were dropped by policing -
I deleted all my playlist by mistake from itunes. tried copying them to on the go on ipod and thought it would copy it on to my itune but it didn't. does any one know how i can do this without redoing all my playlists. thanks
Are the playlists still on the iPod? If so I can probably cook up a script to read them back into iTunes, or you can check the features of the various tools listed at the end of this user tip to see if you can find one that you want to use.
tt2 -
Can I convert a proxy for a class that does not has any interfaces?
Can I convert a proxy for a class that does not has any interfaces?
Hi.
I can hardly understand your question: what do you want your proxy (what kind of proxy?) to be converted into?
All I can tell you is the following: Proxies created using java.lang.reflect.Proxy can only be created using an interface. This interface has to be implemented by the proxied object. So: no interface, no java.lang.reflect.Proxy.
Bye. -
Why does mls qos trust dscp dissapear after reboot?
The command takes but after reboot, Invlaid inputs detected show up and "mls qos tust dscp" is gone from every interface.
Happens on both 2960-24PC-S / 2960-48PST-S switches.Hi,
thanks for your reply.
mls qos
interface GigabitEthernet3/34
description *** DATA VLAN 35 - VOICE VLAN 34 ***
switchport
switchport trunk native vlan 36
switchport trunk allowed vlan 34,36
switchport mode trunk
mls qos trust dscp
no cdp enable
spanning-tree portfast trunk
If i don't include the global 'mls qos' command then the voice packets keep the dscp 46 value. If I add the mls qos command this causes the switch to set the dscp values to zero.
Thanks again
ps. there are some other mls commands on the switch... i don't know if these could interfere but they were already on there so i'm reluctant to remove them.. -
I find it ABSOLUTELY unacceptable that since recently safari opens up random "commercial websites" without me clicking on any link. And it does that without allowing me to go (back) to the site I really clicked on. STOP THAT!!!!!!
There is no need to download anything to solve this problem. You may have installed a variant of the "VSearch" ad-injection malware. Follow Apple Support's instructions to remove it.
If you have trouble following those instructions, see below.
Malware is always changing to get around the defenses against it. This procedure works as of now, as far as I know. It may not work in the future. Anyone finding this comment a few days or more after it was posted should look for a more recent discussion, or start a new one.
The VSearch malware tries to hide itself by varying the names of the files it installs. To remove it, you must first identify the naming pattern.
Triple-click the line below on this page to select it, then copy the text to the Clipboard by pressing the key combination command-C:
/Library/LaunchDaemons
In the Finder, select
Go ▹ Go to Folder...
from the menu bar and paste into the box that opens by pressing command-V. You won't see what you pasted because a line break is included. Press return.
A folder named "LaunchDaemons" may open. Look inside it for two files with names of the form
com.something.daemon.plist
and
com.something.helper.plist
Here something is a variable string of characters, which can be different in each case. So far it has always been a string of letters without punctuation, such as "cloud," "dot," "highway," "submarine," or "trusteddownloads." Sometimes it's a meaningless string such as "e8dec5ae7fc75c28" rather than a word. Sometimes the string is "apple," and then you must be especially careful not to delete the wrong files, because many built-in OS X files have similar names.
If you find these files, leave the LaunchDaemons folder open, and open the following folder in the same way:
/Library/LaunchAgents
In this folder, there may be a file named
com.something.agent.plist
where the string something is the same as before.
If you feel confident that you've identified the above files, back up all data, then drag just those three files—nothing else—to the Trash. You may be prompted for your administrator login password. Close the Finder windows and restart the computer.
Don't delete the "LaunchAgents" or "LaunchDaemons" folder or anything else inside either one.
The malware is now permanently inactivated, as long as you never reinstall it. You can stop here if you like, or you can remove two remaining components for the sake of completeness.
Open this folder:
/Library/Application Support
If it has a subfolder named just
something
where something is the same string you saw before, drag that subfolder to the Trash and close the window.
Don't delete the "Application Support" folder or anything else inside it.
Finally, in this folder:
/System/Library/Frameworks
there may an item named exactly
v.framework
It's actually a folder, though it has a different icon than usual. This item always has the above name; it doesn't vary. Drag it to the Trash and close the window.
Don't delete the "Frameworks" folder or anything else inside it.
If you didn't find the files or you're not sure about the identification, post what you found.
If in doubt, or if you have no backups, change nothing at all.
The trouble may have started when you downloaded and ran an application called "MPlayerX." That's the name of a legitimate free movie player, but the name is also used fraudulently to distribute VSearch. If there is an item with that name in the Applications folder, delete it, and if you wish, replace it with the genuine article from mplayerx.org.
This trojan is often found on illegal websites that traffic in pirated content such as movies. If you, or anyone else who uses the computer, visit such sites and follow prompts to install software, you can expect more of the same, and worse, to follow. Never install any software that you downloaded from a bittorrent, or that was downloaded by someone else from an unknown source.
In the Security & Privacy pane of System Preferences, select the General tab. The radio button marked Anywhere should not be selected. If it is, click the lock icon to unlock the settings, then select one of the other buttons. After that, don't ignore a warning that you are about to run or install an application from an unknown developer.
Then, still in System Preferences, open the App Store or Software Update pane and check the box marked
Install system data files and security updates (OS X 10.10 or later)
or
Download updates automatically (OS X 10.9 or earlier)
if it's not already checked.
Maybe you are looking for
-
Indesign Loses Text Gradient After Export To PDF SWF
I have some Indesign files from a client and everytime I export from indesign to pdf and then convert to a swf, it removes the text gradient and adds black instead. Images attached for reference. <---PDF <---SWF I've tried numerous export options. Is
-
Hello To All Experts !! I wanna looking for some help in displaying image in my text area when should i type ":)" in text field..... I got some program through forums.... import java.util.*; import javax.swing.ImageIcon; public class TokenizeSmiley {
-
Seeking 8.1.7.4 download for Linux x86 - urgent
Does anyone know where I can download a copy of this? We are down right now and waiting for the CD is going to be too costly (that is, after someone from Oracle decides to call me back). Thanks for any help.
-
Illustrator CS5.1 has stopped working
Hi, I just bought CS 5.5 and am having a lot of issues with Illustrator. I was working on a drawing and I was able to save it until I tried to change the colors on my lines and now everytime I try to save it the program says Adobe Illustrator CS 5.1
-
RTMP Live Stream does not resume with Spark VideoPlayer Component
Hi all The Flex 4 framework brought along the VideoPlayer component, which supposedly can automatically choose the best stream in terms of bitrate from a list of available multi-bitrate streams, play live videos and everything. See http://help.adobe.