WRV200 not passing VPN
I have setup for a customer a WRV200 and they have one subtenant that needs to connect to her corporate office via Cisco VPN, but the router is not allowing her to do so and gives a connection error both the primary connection and secondary. I have even opened port triggering to see if that helps and no go. Please let me know why it's not doing the VPN Pass-through. Thanks
P.S. Will be providing screen shot of error once I receive it.
Hi Scott,
As a first step, verify you have the latest release of code on the WRV200, Firmware version 1.0.39 ?
You can check this by viewing the top right side of the management GUI within the WRV200.
Dumb question maybe, but have you also enabled IPSec passthru on the router.
Has she 'enabled transparent tunneling' on her client
If your answer is yes, you better have a chat to the folks the Small business TAC (S-TAC). Contact Link to this new Small business support center is below.
http://www.cisco.com/en/US/partner/support/tsd_cisco_small_business_support_center_contacts.html#csb
http://www.cisco.com/en/US/partner/support/tsd_cisco_small_business_support_center_contacts.html#csbhttp://www.cisco.com/en/US/partner/support/tsd_cisco_small_business_support_center_contacts.html#csb
Similar Messages
-
Server 2003 routing and remote access not passing VPN traffic
I've inherited a network that has two IP scopes that are routed through a Windows 2003 server with Routing and Remote Access. I can ping both sides (we'll call them HQ and Plant) internally. My firewall has an IP from the HQ IP scope and when
I connect via VPN, I can see all the devices on the HQ network including the network card that is in the routing server for that "side". However, if I'm connected via VPN, I cannot get to any of the IPs on the Plant side, not even the card
in the routing server. The buck stops on the server.
I should mention, that the firewall assigns IP addresses that are on the HQ scope, so all VPN connections will have an address from that side.
I'm lost on how to get this set up so my VPN traffic coming in from the HQ side can be routed to the Plant devices.Hi,
To be honest, your statement confused me a bit.
VPN is used for external client get access to internal resource. When we setup VPN server, we usually have two NICs. We need choose a NIC that will be used when client initiate
a connection request. I prefer to call it external NIC card. The internal one will work as DHCP relay agent. So this is a single way connection. You cannot dial from internal to external.
If I misunderstood you, please elaborate what you are trying to do.
Hope this helps. -
Cisco 881 ISR IPSec VPN Tunnel does not pass traffic from the vlan.
I have a cisco 881 ISR Router with a site-to-site IPsec vpn tunnel to a mikrotik device on the other end (I inherited this from my client). The tunnel is constructed properly and is up, however traffic does not pass or get routed to the FA4 interface. I see in my packet captures that it hits the vlan1 interface (vlans are required on the L2 ports) and does not pass to the tunnel.
This is my configuration:
141Kerioth#sh config
Using 3763 out of 262136 bytes
! Last configuration change at 01:02:41 UTC Mon May 26 2014 by admin
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname 141Kerioth
boot-start-marker
boot-end-marker
logging buffered 51200 warnings
aaa new-model
141Kerioth#do wr mem
^
% Invalid input detected at '^' marker.
141Kerioth#wr mem
Building configuration...
[OK]
141Kerioth#sh run
Building configuration...
Current configuration : 5053 bytes
! Last configuration change at 01:38:06 UTC Mon May 26 2014 by admin
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname 141Kerioth
boot-start-marker
boot-end-marker
logging buffered 51200 warnings
aaa new-model
aaa authentication login default local
aaa authentication ppp default local
aaa session-id common
memory-size iomem 10
crypto pki trustpoint TP-self-signed-580381394
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-580381394
revocation-check none
rsakeypair TP-self-signed-580381394
crypto pki certificate chain TP-self-signed-580381394
certificate self-signed 01
30820229 30820192 A0030201 02020101 300D0609 2A864886 F70D0101 05050030
30312E30 2C060355 04031325 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 35383033 38313339 34301E17 0D313430 35323231 38323333
365A170D 32303031 30313030 30303030 5A303031 2E302C06 03550403 1325494F
532D5365 6C662D53 69676E65 642D4365 72746966 69636174 652D3538 30333831
33393430 819F300D 06092A86 4886F70D 01010105 0003818D 00308189 02818100
B001A012 2CA6970C 0648798B 2A786704 84F2D989 83974B19 9B4287F2 4503D2C9
173F23C4 FF34D160 202A7565 4A1CE08B 60B3ADAE 6E19EE6E 9CD39E72 71F9650E
930F22FE C4441F9C 2D7DD420 71F75DFC 3CCAC94E BA304685 E0E62658 A3E8D01C
D01D7D6A 5AF0B0E6 3CF6AF3A B7E51F83 9BF6D38E 65254E1F 71369718 ADADD691
02030100 01A35330 51300F06 03551D13 0101FF04 05300301 01FF301F 0603551D
23041830 168014D6 24878F12 1FFADF2F 537A438E 6DD7FB6B D79E4130 1D060355
1D0E0416 0414D624 878F121F FADF2F53 7A438E6D D7FB6BD7 9E41300D 06092A86
4886F70D 01010505 00038181 00771667 FCA66002 8AB9E5FB F210012F C50B586F
9A9640BB 45B4CEFD 030A38C0 E610AAC8 B41EF3C4 E55810F9 B2C727CF C1DEFCF1
0846E7BC 1D95420E 5DADB5F8 EFE7EB37 B5433B80 4FF787D4 B1F2A527 06F065A4
00522E97 A9D2335C E83C4AE1 E68D7A41 9D0046A7 ADCC282B 7527F84D E71CC567
14EF37EA 15E57AD0 3C5D01F3 EF
quit
ip dhcp excluded-address 10.0.16.1
ip dhcp pool ccp-pool
import all
network 10.0.16.0 255.255.255.0
default-router 10.0.16.1
dns-server 8.8.8.8
lease 0 2
ip domain name kerioth.com
ip host hostname.domain z.z.z.z
ip name-server 8.8.8.8
ip name-server 4.2.2.2
ip cef
no ipv6 cef
license udi pid CISCO881-K9 sn FTX180483DD
username admin privilege 15 secret 4 CmmfIy.RPySmo4Q2gEIZ2jlr3J.bTBAszoe5Bry0z4c
username meadowbrook privilege 0 password 0 $8UBr#Ux
username meadowbrook autocommand exit
policy-map type inspect outbound-policy
crypto isakmp policy 1
encr 3des
authentication pre-share
group 5
crypto isakmp key 141Township address z.z.z.z
crypto isakmp keepalive 10
crypto ipsec transform-set TS esp-3des esp-sha-hmac
mode tunnel
crypto map mymap 10 ipsec-isakmp
set peer z.z.z.z
set transform-set TS
match address 115
interface Loopback0
no ip address
interface Tunnel1
no ip address
interface FastEthernet0
no ip address
interface FastEthernet1
no ip address
interface FastEthernet2
no ip address
interface FastEthernet3
no ip address
interface FastEthernet4
description $FW_OUTSIDE_WAN$
ip address 50.y.y.y 255.255.255.240
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
crypto map mymap
interface Vlan1
description $ETH_LAN$
ip address 10.0.16.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
ip tcp adjust-mss 1452
ip forward-protocol nd
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip nat inside source list 115 interface Vlan1 overload
ip nat inside source list 199 interface FastEthernet4 overload
ip nat inside source route-map nonat interface FastEthernet4 overload
ip route 0.0.0.0 0.0.0.0 50.x.x.x
access-list 110 deny ip 10.0.16.0 0.0.0.255 10.0.1.0 0.0.0.255
access-list 110 permit ip 10.0.16.0 0.0.0.255 any
access-list 115 permit ip 10.0.16.0 0.0.0.255 10.0.1.0 0.0.0.255
access-list 144 permit icmp host c.c.c.c host 10.0.1.50
access-list 144 permit icmp host p.p.p.p host 10.0.16.105
access-list 199 permit ip a.a.a.a 0.0.0.255 any
no cdp run
route-map nonat permit 10
match ip address 100
line con 0
no modem enable
line aux 0
line vty 0 4
access-class 1 in
exec-timeout 30 0
privilege level 15
transport preferred ssh
transport input ssh
line vty 5 15
access-class 23 in
privilege level 15
transport input telnet ssh
cns trusted-server all-agents x.x.x.x
cns trusted-server all-agents hostname
cns trusted-server all-agents hostname.domain
cns id hardware-serial
cns id hardware-serial event
cns id hardware-serial image
cns event hostname.domain 11011
cns config initial hostname.domain 80
cns config partial hostname.domain 80
cns exec 80
endWhy do you have following command on the PIX?
crypto map outside_map 40 set transform-set 165.228.x.x
Also you have this transform set on the PIX:
crypto ipsec transform-set 10.112.60.0 esp-aes-256 esp-sha-hmac
This does not match the transfor set on the router:
crypto ipsec transform-set tritest esp-3des esp-md5-hmac
Where are you using the access-list/route-map
101 ? -
DHCP Server is not passing out DHCP Leases
I can't seem to figure out why DHCP server is not passing out DHCP lease a client?
Also I can't seem to figure out why NVI0 interface is UP? I have setup another box similarly and NVI0 is down on that and the DHCP server is working fine on that too. Strange!
I am working on CISCO 881 VPN Router...Please have a look at it and let me know. Thanks
Here is the configuration in the box...
sh run
Building configuration...
Current configuration : 6543 bytes
! Last configuration change at 17:09:54 CST Fri Sep 14 2012 by XXXXX
version 15.0
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname XXXXX
boot-start-marker
boot-end-marker
logging buffered 51200 warnings
aaa new-model
aaa authentication login default local
aaa authentication login vpn_xauth_ml_1 local
aaa authentication login sslvpn local
aaa authorization network vpn_group_ml_1 local
aaa session-id common
memory-size iomem 10
clock timezone CSTime -6
clock summer-time CST recurring
crypto pki trustpoint TP-self-signed-3079619067
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-3079619067
revocation-check none
rsakeypair TP-self-signed-3079619067
crypto pki certificate chain TP-self-signed-3079619067
certificate self-signed 01
30820252 308201BB A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 33303739 36313930 3637301E 170D3132 30393134 31393231
32375A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D33 30373936
31393036 3730819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100993C D622004B F3AEA1E5 81106C28 36EC52D0 5435ABC3 8912095F 3641168A
B67D97AF AEB43CF3 00A00EB5 702FA355 9F58EBEF F42294DC 0E32CF40 E17D372A
3BC36401 55EDBA5C 910B7A51 89D709A8 7EAB3FF0 E4C99D34 CBE3F316 069C0E16
BC284055 35E3D762 463DABF6 852C4E7A D2EF45A4 21F08689 4DF17870 9E2A6C27
1BFB0203 010001A3 7A307830 0F060355 1D130101 FF040530 030101FF 30250603
551D1104 1E301C82 1A506F70 6C617276 696C6C65 2E796F75 72646F6D 61696E2E
636F6D30 1F060355 1D230418 30168014 64EA4CAE 2029E4C2 702584C6 B5732464
5C9DA38A 301D0603 551D0E04 16041464 EA4CAE20 29E4C270 2584C6B5 7324645C
9DA38A30 0D06092A 864886F7 0D010104 05000381 81006C27 96E06B83 04DBDA81
EEB0AF35 84ED370E A8C9694E F9B9326D 69CB1043 9C396D7B 760D252F 4881926D
878E434F 9AFC3E6D A5BF43F2 E619D6EC F45C039A 5FFB478F A99F7EE5 274E37D5
11976FDE 823FD1A9 700203E5 67A329B3 F4CF45F0 245757C8 E2349276 B13414D1
017616FA 38A40BA8 42545AC5 C7676D21 29E4F491 CADB
quit
ip source-route
ip dhcp excluded-address 10.10.10.1
ip dhcp excluded-address 192.168.1.1 192.168.100.101
ip dhcp excluded-address 192.168.1.254
ip dhcp pool ccp-pool
import all
network 10.10.10.0 255.255.255.248
default-router 10.10.10.1
lease 0 2
ip dhcp pool Internal_Network
network 192.168.1.0 255.255.255.0
dns-server 192.168.100.254
default-router 192.168.1.254
ip cef
ip domain name yourdomain.com
ip name-server 192.168.100.254
no ipv6 cef
license udi pid CISCO881-K9 sn FTX1604828T
username XXXXX privilege 15 secret 5 $1$QEcR$96cmvs/h/.05G6BnorcWG/
username XXXXX secret 5 $1$PQQ1$3.Vin0i/2uZ/KD0xEJ8GC.
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
crypto isakmp policy 2
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp client configuration group YYYYYYY
key XXXXX_XXXXX_XXXXX
pool VPN-Pool
acl VPN-Access-List
crypto isakmp profile vpn-isakmp-profile-1
match identity group YYYYYYY
client authentication list vpn_xauth_ml_1
isakmp authorization list vpn_group_ml_1
client configuration address respond
virtual-template 2
crypto ipsec transform-set encrypt-method-1 esp-3des esp-sha-hmac
crypto ipsec profile VPN-Profile-1
set transform-set encrypt-method-1
interface FastEthernet0
interface FastEthernet1
interface FastEthernet2
interface FastEthernet3
interface FastEthernet4
description WAN_INTERFACE
ip address 192.168.100.3 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
interface Virtual-Template2 type tunnel
ip unnumbered FastEthernet0
tunnel mode ipsec ipv4
tunnel protection ipsec profile VPN-Profile-1
interface Vlan1
description VLAN1_INTERFACE
ip address 192.168.1.254 255.255.255.0
no ip redirects
no ip unreachables
ip nat inside
ip virtual-reassembly
ip tcp adjust-mss 1452
ip local pool VPN-Pool 192.168.1.151 192.168.1.200
ip forward-protocol nd
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip nat inside source list 100 interface FastEthernet4 overload
ip nat inside source static tcp 192.168.1.100 21 192.168.100.3 21 extendable
ip nat inside source static tcp 192.168.1.100 80 192.168.100.3 80 extendable
ip route 0.0.0.0 0.0.0.0 192.168.100.254
ip access-list extended VPN-Access-List
permit ip 192.168.1.0 0.0.0.255 any
permit tcp host A.B.C.D host 192.168.1.100 eq ftp
permit tcp host A1.B1.C1.D1 host 192.168.1.100 eq ftp
permit tcp host A2.B2.C2.D2 host 192.168.1.100 eq ftp
permit tcp 192.168.1.0 0.0.0.255 host 192.168.1.100 eq ftp
permit tcp host A3.B3.C3.D3 host 192.168.1.100 eq ftp
permit tcp any host 192.168.1.100 eq XXX
access-list 23 permit 10.10.10.0 0.0.0.7
access-list 23 permit 192.168.1.0 0.0.0.255
access-list 100 permit ip 192.168.1.0 0.0.0.255 any
no cdp run
control-plane
banner exec ^C
% Password expiration warning.
Cisco Configuration Professional (Cisco CP) is installed on this device
and it provides the default username "cisco" for one-time use. If you have
already used the username "cisco" to login to the router and your IOS image
supports the "one-time" user option, then this username has already expired.
You will not be able to login to the router with this username after you exit
this session.
It is strongly suggested that you create a new username with a privilege level
of 15 using the following command.
username <myuser> privilege 15 secret 0 <mypassword>
Replace <myuser> and <mypassword> with the username and password you
want to use.
^C
banner motd ^C XXXXX-XXXXX VPN Router ^C
line con 0
exec-timeout 30 0
logging synchronous
no modem enable
line aux 0
line vty 0 4
access-class 23 in
privilege level 15
password 7 124A50424A5E5550
transport input telnet ssh
scheduler max-task-time 5000
endHi Jennifer,
I have gotten it resolved. Per your suggestion, I have turned on debug ip dhcp events and found that POOL EMPTY message. After little research, I found out that I have made a mistake in my excluded-address range.
I have had it as
ip dhcp excluded-address 192.168.1.1 192.168.100.101
It should have been
ip dhcp excluded-address 192.168.1.1 192.168.1.101.
It was a typo.
Thank you for the suggestion.
Srini -
GRE traffic can not pass through LRT224 IPSec Tunnel
Hi,
We have a trouble when using Cisco Router GRE tunnel plus LRT224 IPSec Gateway-Gateway Tunnel.
We found after reboot, GRE packets can not pass trough LRT224 IPSec tunnel. need to restart serval time then gre will back to normal.
Besides that, GRE keepalive packets can not pass trough LRT224 IPSec Tunnel.
please help. I had tried to upgrade to latest firmware version.
Firmware Version : v1.0.3.09 (Dec 26 2014 14:28:46)
A-END:
interface Tunnel1
ip address 10.216.80.105 255.255.255.252
ip mtu 1400
ip nat outside
ip virtual-reassembly in
ip tcp adjust-mss 1360
ip ospf network point-to-point
ip ospf hello-interval 3
ip ospf cost 10000
tunnel source 10.216.81.2
tunnel destination 10.216.80.90
end
B-END:
interface Tunnel11
ip address 10.216.80.110 255.255.255.252
ip mtu 1400
ip tcp adjust-mss 1360
ip ospf network point-to-point
ip ospf cost 10000
ip ospf hello-interval 3
tunnel source 10.216.80.91
tunnel destination 10.216.81.3
end
CISCO2911 <> LRT224 <> INTERNET <> LRT224 <> CISCO 2621
SanCan you post the results from the below command for the Cisco Routers?
IOS Command: "sh version"
Why not static route without NAT through the LRT224 IPSec VPN?
Just curious why did you use LRT224's for the Site to Site VPN instead of the Cisco Routers?
Please remember to Kudo those that help you.
Linksys
Communities Technical Support -
RV042 not annoucing vpn routes over rip v2
Problem: RV042 is not announcing a class C VPN route via RIP to other routers. It announces the gateway public address via rip, but not the VPN route.
I am attempting to use a pair of RV042 as a redundant links between our home office and a branch. The home office and branch is already connected via a T1. Each location also has an additional cable internet connection with public IP address and a cisco 1921 router controlling the traffic.
The 1921 routers are using OSPF to route traffic over the T1 and have RIPv2 enabled to talk to their local respective RV042s. Here is a description of how the network is set up.
MainRouter - cisco 1921
Eth0 - Network is 192.168.41.0/24
IP address is 192.168.41.20
Eth0/1 - Network 10.1.1.1 255.255.255.254
T1 connection to branch router
MainRV - RV042 v3 with fw 4.2.1.02
Wan1 - Public IP A X.X.X.X
LAN- Network 192.168.41.0/24
IP 192.168.41.11 255.255.255.0
BranchRouter - cisco 1921
Eth0/0 - Network is 192.168.46.0/24
IP address is 192.168.46.10
Eth0/1 - Network 10.1.1.2 255.255.255.254
T1 connection to main router
BranchRV - RV042 v3 with fw 4.2.1.02
Wan1 - Public IP B Y.Y.Y.Y
LAN - Network 192.168.46.0/24
IP 192.168.46.11 255.255.255.0
I have established a VPN from BranchRV to MainRV and it passes traffic correctly. My "MainRouter "
rip database looks like this....
192.168.41.0/24 auto-summary
192.168.41.0/24 directly connected, GigabitEthernet0/0
X.X.X.X/24 auto-summary
X.X.X.Z/30
[1] via 192.168.46.11, 00:00:01, GigabitEthernet0/0
Notice that there is no route to 192.168.46.0/24 in there....
Now here is the kicker, just messing around, I changed the VPN settings to use subnets 10.0.10.0/24 on MainRV and 10.0.11.0/24 on BranchRV instead of 192.168.41.0/24 and 192.168.46.0/24 respectivly. After I tried that the routes for the 10.0.3.0 were announced via RIP
Here is what the MainRouter's rip database looked like after I tried that
10.0.0.0/8 auto-summary
10.0.11.0/24
[2] via 192.168.41.11, 00:00:18, GigabitEthernet0/0
192.168.41.0/24 auto-summary
192.168.41.0/24 directly connected, GigabitEthernet0/0
X.X.X.X/24 auto-summary
X.X.X.Y/30
[1] via 192.168.41.11, 00:00:18, GigabitEthernet0/0
What gives? This really looks like a bug to me...
Anyhow I'm thinking a workaround might be to set up a GRE tunnel across those 10.0.X.X subnets to the other side so I can at least dynamically route traffic accross.... Without the RIP routes being announced I don't have automatic failover!
Thanks for your help,
CurtisYes as was explained to me previously.... by Jason Nickle multicast does not cross a site-to-site tunnel.
That is not what I want to have happen. What I want is for my RV042 to announce it's VPN routes to other routers on the same physical network. Which it currently is not doing.
Site 1
Cisco IOS Router X - main router, local network traffic runs across this
RVO42 X - has VPN link to RVO42 Y at Site 2
Site 2
Cisco IOS Router Y - main router, local newtok traffic runs acress this
RVO42 Y - has VPN link to RVO42 X at Site 1
The problem is that RV042 Y doesn't tell Router Y that it has a route to Site 1. And RV042 X doesn't tell Router X that it has a route to Site 2. So they are not locally announcing via RIP, the routes they have TO the respective remote sites.
What I was trying to say in my original post, is that the router will announce VPN routes if the vpn subnets are a class A 10.X.X.X subnet, but it doesn't announce them if they are a class C 192.168.X.X subnet. So what I am doing should be working, however it is not. -
Captivate 6 Text Entry Events Do Not Pass
I am a long-time user of Captivate going back to version 2. I've created a simulation course with numerous text entry events that do not validate correctly. I am typically using the TAB key to validate the text entered. I have several lessons where everything works fine, but many that have problems.
Typically when TAB is used at the end of a key press, you will see focus shift to the first button on the Play bar - and this does not cause any problems. I see this behavior on the events in my course that work. However, for the ones that do not work, I see the focus shifting to the Address Bar and the event will not pass.
The only workaround I have employed is to use On Focus Lost: Go to Next. This is not a great solution because the text no longer validates with this setting. These events will pass no matter what is entered.
I would really appreciate your help with this! My course is due soon. I would be happy to provide more information or upload my file for your inspection. Thank you!For anyone who might be experiencing the same problem and looking for an answer - this is still 100% broken in Captivate version 6. None of the fixes discussed in the above referenced thread work. I tried playbar widgets, editing the playbars in Flash. No luck.
Adobe just moves forward from version to version not fixing the bugs they create in prior versions. That's your incentive to upgrade, folks.
Best workaround I can offer is Use ENTER as your validation keystroke. It doesn't have the same problems associated with TAB. Good luck! -
Scheduling Agreement -Schedule line should not pass the requirement to MRP
Hi Friends!
As we all know the scheduling agreements is outline agreement with future schedule lines, with this system will pass the requirements to MRP for the schedule line which is even after 5 years, so my requirement is if the schedule line date is above 15 days from the current date then requirement should not pass to MRP.
solution which we gave is, SA initially will determine the schedule line category as CN (which will not transfer the requirement) and a batch job program will run daily and it will check for each schedule line if any of the schedule is with in the 15 days from the current date then it will change the schedule line category from CN to CP.
Now the problem is , by using Batch Job which program I have to call to change the schedule line category?????
1. we tried BAPI_SALESORDER_CHANGE but when we are changing the CN to CP it is not performing ATP where as if we do manually it is performing.
2. we tried BDC but here also we facing some strange problem i.e. while recording the ATP screen is not populating where it is coming while doing manual.
Can someone let me know which one program we should call in Batch job to do this change.
Regards
NathHi nath,
i also failed in changing shedule line category in userexit and in BAPI.
in one case, i succeded in doing it with a bdc after MV45AFZZ / userexit_save just bevore the datas are reset but after the commit-work is processed.
the other possibility is, to change the accepted amount in userexit RV03VFZZ / USEREXIT_AVAILABILITY_OUT.
3. possibility is, to block the order with a delivery - block , same as the credit-control-block. This block can be set in MV45AFZZ or perhaps in BAPI too.
hans -
Dashboard prompt value is not passing into the report
Hi,
I am using OBIEE 10g. The problem is in Oracle BI Answers
I have a prompt and its related report. In the prompt, in one of the column, I am using sql result. The sql query is a co-related sub query where i have used 2 tables. employee_data and employee_region. The reason for using sub-query is that there is no data_center column in the employee_data table. It has the records for all the data_center e.g USA, UK,IND,AUSTRALIA etc So, I used the sub query with condition which will give the result on a particular data center (here it is USA) and this sub query's output is input for the main query. And the prompts works fine and gives correct result
The sql query used for the column in the prompt (in Oracle BI Answers) as
SELECT EMPLOYEE_DATA.ENAME FROM EMPLOYEE WHERE EMPLOYEE_DATA.ENAME IN (SELECT EMPLOYEE_REGION.ENAME FROM EMPLOYEE WHERE EMPLOYEE_REGION.DATA_CENTER = 'USA')Now in the report, there are 2 coulmns. - EMPLOYEE_DATA.ENAME and EMPLOYEE_REGION.DATA_CENTER
I have used the main column EMPLOYEE_DATA.ENAME for filter as 'prompted'.
The problem is the value from the prompt is not passing from the prompt to the report, what I found. Because, instead of showing the result for 'USA' data_center, It also shows other data_center 's (UK,IND,AUSTRALIA) data.
How filter condition I should use for EMPLOYEE_DATA.ENAME column in the report so that the prompt value will pass to the report properly ?
Thanks
Edited by: Kuldip on Feb 21, 2013 6:17 AMHi Kuldip,
There are 2 ways of doing it.
1. Nice and good: For the section where the report is put have a condition to display only if it returns rows. For details please refer to :
http://bischool.wordpress.com/category/guided-navigation/
2. The easy way: Add a "No Result" view to your report and add few spaces in the text.
Let me know if this helped.
Regards,
Jay -
Filters 'OR' function not passing the values to the sql
Hi,
I am facing an issue with the 'OR' function on the filters that are used in the reports.
The report needs to fetch all the records on the three tables as the user enters the value in the dashboard prompts.
eg: [ update_dt_A1 is prompted
and user_name_A1 is prompted ]
or
[ update_dt_B1 is prompted
and user_name_B1 is prompted ]
or
[ update_dt_C1 is prompted
and user_name_C1 is prompted ]
The values entered in the dashboard prompt gets passed to the filter, but the vaules are not passed over to the SQL that runs on the database, hence the reports shows all values and does not reflect the values entered.
When the 'OR' function is replaced with 'AND' the values get passed to the SQL.
Can anyone help on what is the issue on the filters?
ThanksHere is how my Filters are set up
Vendor Name is Prompted
AND
Vendor Number is Prompted
AND
[ [Last_update_date_Vendor is prompted
AND
User_name_Vendor is prompted]
OR
[Last_update_date_Site is prompted
AND
User_name_Site is prompted]
OR
[Last_update_date_Bank is prompted
AND
User_name_Bank is prompted]
The values from the dashboard prompts gets passed to the filter, but the sql that runs does not take the values in the where clause. -
While updating my ipad to ios7, I could not pass the terms and conditions screen where I had to agree or disagree. It just didn't move pass that screen. I can't do anything to go forward or back. It's just stuck there.
Try to reset the device:
Device Reset (won't affect settings/data/music/apps/etc)
1. Press and hold (& continue to hold) BOTH the Sleep/Wake button & the Home button.
2. Continue to hold BOTH (ignoring any other messages that may show) until you see the Apple logo on the screen.
3. Release BOTH buttons when you see the Apple logo and allow the device to boot normally. -
Smb error -36 on one server but not another (vpn)
Here goes:
I'm connecting using the built-in Apple VPN client to work.
Once connected, I try to mount two Windows servers using the finder:
* The first one asks my username/password and mounts no problem.
* The 2nd doesn't seem to ask for username/password, and just gives me the dreaded "error -36"
The console says:
Unknown host
mount_smbfs: can't get server address: syserr = Network is down
mount_smbfs: can't get server address 'XXXXXXXXXXX'
But the network is up (I know, since I am moving files from the other server).
When connecting from inside the office (not via VPN) all is well.
What gives?Here goes:
I'm connecting using the built-in Apple VPN client to work.
Once connected, I try to mount two Windows servers using the finder:
* The first one asks my username/password and mounts no problem.
* The 2nd doesn't seem to ask for username/password, and just gives me the dreaded "error -36"
The console says:
Unknown host
mount_smbfs: can't get server address: syserr = Network is down
mount_smbfs: can't get server address 'XXXXXXXXXXX'
But the network is up (I know, since I am moving files from the other server).
When connecting from inside the office (not via VPN) all is well.
What gives? -
How to resolve a Lenovo PC that will not pass the Lenovo Splash screen with no access to Windows
Here is my problem and here is the solution!!!
My B540 Ideacentre would not pass the Lenovo splash screen. The only operational keys I had was F1 (BIOS) and F12 (BIOS options). F2 went to a light blue screen so no chance of even a one key recovery. Warrenty had expired four and a half months ago. I contacted Lenovo and after the guy told me to try F2 twice he said it was a HDD or other hardware failure and would cost around £200 maybe and also would take about two weeks.
AT THIS POINT YOU SHOULD NOT BE ANGRY FRUSTRATED OR PANIC. REMAIN CALM AND STOP AND THINK WHAT ACTUALLY WAS HAPPENING WHEN YOU LAST USED YOUR PC.
For me I remembered Windows had auto downloaded 8.1 and was asking me to install. Also my keyboard had lost shift W T Y keys. This told me that it was not a hardware issue but a software issue and perhaps from this update. My HDD was not clicking or beeping and this PC has a 2TB Seagate Barracuda which has a good reputation. Luckly for me I also have a Seagate external expansion 2TB and a 500MB expansion which was the HDD from my old HP Touchsmart which I converted into an external hard drive by buying a HDD enclosure with cooling fan and all leads from eBay for £25 and this is where the solution is.
If you can create an expansion drive so easily and access the HDD then why cant I do it with the HDD from my Ideacentre and of course you can. So first unplug your PC or laptop. Next remove the cover and unclip the HDD (which is easy with the B540. See user instructions). Next I removed my HP HDD from the enclosure and fitted my Ideacentre HDD in its place. Next you need a laptop or another PC. Switch it on and then connect your HDD to the laptop or PC via highspeed USB cable. My laptop is running Windows 7 Ultimate and of course has all the repair tools required. When the software has loaded you may get a box that will have two options. The first will ask you if you want to repair your files and the second to scan for bad sectors and to attempt repair recovery of sectors. Tick both boxes and click start. This is a long slow process but worth the wait. Nine hours later my HDD was ready. I connected my Seagate expansion to my laptop and moved all new files that I had not backed up. So at this point you should create a folder and move all your photos music videos documents etc to it. This can take upto three hours if you have never backed up before and are moving everything. Once completed I shut everything down and replaced the HDD into my Ideacentre. Make sure do not have any external devices connected such as expansions external drives headphones etc. Connect the power and switch on. The Ideacentre booted up and there was a pause at the splash screen then it went to a black screen and then by the miracle of logical thinking I was at my lock screen. I was never so glad to see the map of my home land "Ukraine". After jumping up and down with joy I then went in and all was as normal but to be sure I went into safemode and started a complete restore. This is the option where you completely format your HDD and restore as new. It takes a long time but it is the best option because you do not want this to happen again. When this has completed and you are in Windows do not wait a moment longer by playing with your photos or creating your desktop picture. Go to create a recovery drive (use a 32GB stick) and after that also make a copy to disc. Next go to command prompt (cmd) Admin and change a setting by typing bcdedit /set {default} bootmenupolicy legacy. This will now enable your F8 key to boot straight into safemode just incase you need to in the future. It will slow boot time a little but better to be able to get in to Windows than not at all for the sake of a few seconds.
Well I hope this helps someone out there and I know you may think its a lot to do but it is not. Ask a friend to borrow a laptop or PC and perhaps a HDD encloser. The rest is just time but when you see your lock screen you will not care trust me.
Cлава Україні!!! Героям слава!!!I thought this was the method I used before but I followed through it and it was a horrific fail. "Operating system not found". Can anyone help?
http://superuser.com/questions/421402/how-to-create-a-bootable-usb-windows-os-us ing-mac-os-x
Steps To Achieve Victory
Download the ISO you want to use
Open Terminal (in /Applications/Utilities)
Convert .iso to .img using hdiutil:
hdiutil convert -format UDRW -o /path/to/target.img /path/to/source.iso
Rename if OS X gave it a .dmg ending:
mv /path/to/target.img.dmg path/to/target.img
Type diskutil to get a list of currently connected devices
Insert USB drive you want to use
Run diskutil again to see what your USB stick gets assigned eg - /dev/disk3
Run diskutil unmountDisk /dev/diskN (where N is the number assigned to your USB stick, in previous example it would be 3)
Run sudo dd if=/path/to/target.img of=/dev/diskN bs=1m (if you get an error, replace bs=1m with bs=1M
Run diskutil eject /dev/diskN and remove your USB stick
The USB stick will now be ready to use
Also similarly described here: http://www.tomshardware.co.uk/answers/id-1733410/creating-microsoft-bootable-usb -mountain-lion.html#. -
The Joomla content management system version 1.0.15 provides a content editor which uses pop-up windows to select images and files. When using any of these pop up editor windows since 3.6.9 the URLs selected in the pop-up are not passed back to the main editor window.
Up until FF 3.6.8 there were no problems, but FF 3.6.9 and 3.6.10 both exhibit this same problem, as does FF 4 Beta 6. (Support Question raised on this forum in early September when 2.6.9 was released but no response)Do you have that problem when running in the Firefox SafeMode?
[http://support.mozilla.com/en-US/kb/Safe+Mode]
''Don't select anything right now, just use "Continue in SafeMode."''
If not, see this:
[http://support.mozilla.com/en-US/kb/troubleshooting+extensions+and+themes] -
Cancel Credit Memo Not passed to Accounting
Hi, All
My client have a Issue there raised Credit memo request with reference to billing document later there convert into Credit Memo, later there found amount there given is wrong credit memo request, there cancel credit memo the problem is that system not generate any accounting document Due to the Number range Issue and we fix the issue ( Same Series of number ranges RV and accounting ) previous it was the other Series of number ranges
The problem is Cancellation of credit memo not passed to accounting and credit memo already passed to accounting
Can we delete Billing document not passed to Accounting So i can again Cancel the Credit memo
it very urgentt
Thanks
RajeshHi,
to cance a cancellation document, check note 388489.
But the status of the original document won't change thus you cannot cancel it again. The solution is creating a debit memo.
Balazs
Maybe you are looking for
-
I have a EJB SLSB and I can deploy it to OC4J 10.1.2.0.2. However upon deployment OC4J is telling me: Note: Some input files use or override a deprecated API. Note: Recompile with -deprecation for detailsCan somebody tell me how I can make OC4J recom
-
Xws-security and fault messages
Hi, I have a problem with xws-security and fault messages. It seems that the security policy is not applied to fault messages. This results in a "javax.xml.rpc.soap.SOAPFaultException: Message does not conform to configured policy: No Security Header
-
Image = JAI.create("stream",bass) problem
I get the exception "Stream - Parameter value`s class (com.sun.media.jai.codec.ByteArraySeekableStream) is not an instance of the parameter class (com.sun.media.jai.codec.SeekableStream) for parameter "stream". " with the following code - not sure wh
-
How do I stop all the emails from ASC, I went to the privacy policy and shut it off there but it says it takes 10 days to kick in, meanwhile I'm getting 100's off emails and was only interested in a specific topic, but I'm getting emails on everythin
-
Hi All! I am really struggling with Java these days, as I am not good at programming but need to finish an assignment at college by using it. Could somebody tell me how I could set the size of fonts on a String and how I would be able to format it, a