WRV210- Can't establish Remote Desktop Connection over IPSec

Hi there,
I changed the BEFVP41 with WRV220 and configure the VPN the same way, succeed to establish IPSec VPN connection with TGB VPN client with no problems but now Remote Desktop Doesn't work. I changed the firmware that didn't help. That didn't help as well, the answer is the same:The client could not connect to the remote computer. Remote connection might not be enabled or the computer might be too busy to accept new connections.The Remote connection works fine in local and with BEFVP41 (even thou I had different problems with this one) the only change is the WRV210....Did you have this issue?
Thank you
Vesna

As a sort of work around, you could configure a dhcp reservation for that pc. Leave the machine as dhcp but know that it will always "recieve" a specific address. I think the problem the WRV210 experiences in this situation, is the mac address table times out and it flushes the pc's mac to ip binding. Therefore, it does not know who to send the request for X ip address to, because it no longer has a mac to port mapping.
However, when the router has the client via DHCP, the dhcp protocol takes care of making sure the mac does not time out in the CAM table. When the lease is somewhat close to expiration, the client renews and everything works fine. You can staticly map up to 20 addresses in the WRV210 (confirmed with configuration in lab).
With this solution, your RDP sessions and port forwardings will continue to work, and your mac will never timeout of the CAM table.
Bill

Similar Messages

Problem Establishing Remote Desktop Connection from Win 7 64Bit

I just got a new Lenovo laptop running Windows 7 Pro 64 Bit with Service Pack 1. I have installed all Win 7 Updates.
When I try to connect to other Windows 7 Ultimate (32 bit) desktops through Remote Desktop Connection over my LAN, I get the following error:
"An authentication error has occurred. The requested security package does not exist"
I can connect to a Windows Small Business Server 2003 32 bit server from the laptop without problem.
All machines are members of the same Windows domain.
The Windows 7 machines I am trying to connect to can connect to each other without issue. NLA is set as not required on each of the desktops, though I have tried turning the NLA setting on, and received the same error.
I have even tried running the 32 bit version of mstsc.exe and disabling the 64 bit version as discussed here:
http://www.davidmoore.info/2009/12/02/running-32-bit-remote-desktop-connection-on-windows-64-bit/
This had no effect either.

Hi,
Based on my research, please check whether the value of HKLM\SYSTEM\CurrentControlSet\Control\Lsa\Security Packages is
kerberos
msv1_0
schannel
wdigest
tspkg
pku2u
If not, please correct it and see how it works.
Note: Serious problems might occur if you modify the registry incorrectly. Therefore, make sure that you follow these steps carefully. For added protection, back up the registry before you modify it. Then, you can restore the registry if a problem occurs. For
more information about how to back up and restore the registry, please refer to
How to back up and restore the registry in Windows.
Hope this helps.
Jeremy Wu
TechNet Community Support

Can I use Remote Desktop Connection (windows server 2008) even if no user is logged in?

I'm configuring a Server, running Windows Server 2008, to be accessed remotely. Suppose no user is logged in in the server (if it was just turned
on, for instance). Can I use the "Remote Desktop Connection" feature to log in remotely in this case? Or is it always necessary to have a user locally logged in, to remotely log in to one of the users available?

If its a fresh installation, RDM might not work at first.
1. You need to check firewall and allow Remote Desktop. To be specific, communication to port 3389 TCP
2. Right click My Computer --> Properties --> Remote tab
Enable Remote Desktop
Allow connections to this computer
Click users and grant the permissions for the users. By default, Administrators do have the permission. An also, the users who are members of the 'Remote Desktop Users' security group also have the permission

Unable to establish Remote Desktop Connection (RDC)

Hi all,
I had activated my account for Instance of SAP Business Warehouse 7.4 SP5 incl. SAP Business Objects BI 4.1 SP2 on SAP HANA 1.0 SP7 but while trying to connect using remote desktop connection, I am unable to connect. Its throwing up the error, "Remote desktop can't connect to the remote computer for one of these reasons". The screen shot of the error message is attached to this post.
I am trying to connect to the servers 54.204.35.135 (SAP Frontend) and 54.225.249.36 (SAP Server). Both of them I am getting the same message.
After I activate the instance on CAL, I see that on Amazon Cloud these instances are automatically started. Then I go to elastic IP and hit on associate these IPs to associate them.
Please let me know if I need to do anything else.I am using a company laptop and am afraid if these IP addresses are being blocked somewhere.
Please advise how to establilsh the RDC.
Thank you.
Regards,
Pavan.

Hi Pavan,
the following comment in your initial question draw my attention:
After I activate the instance on CAL, I see that on Amazon Cloud these instances are automatically started. Then I go to elastic IP and hit on associate these IPs to associate them.
So you started the solution (that contains 2 images) in CAL and then changed some configuration settings in the EC2 web console, correct?
It is important to understand, that changes to the configuration of the instances, that are made outside of CAL will have a severe impact. Only CAL knows how to configure both instances correctly, especially when it comes to the network and communication between each other.
If you don't mind, would you be able to shutdown and terminate all running instances of this Trial solution in CAL and start from scratch without using the EC2 web console. We have throusands of users of this system and all of them get the same software - all works. I suspect the changes in the EC2 console to be a culprit here.
All these activities should be done in CAL, not in the EC2 console:
So please terminate all instances of this solution and wait until they are completely removed.
Then go to the Solution tab and click on create instance
go through the guided procedure and pay attention on the firewall / port settings in step 3
finish and wait 30 minutes until the solution is fully started
try to connect.
Please let us know the result.
Regards,
Hannes

REMOTE DESKTOP CONNECTION (Questions For Experts)

Q1) Is it possible to connect remotely to a computer even if the user is in one country and computer is in another (without internet? If Yes Please tell HOW.
Q2) Is it possible to use hardware like printer while in remote connection with a tab or lets say I am connected with a tablet which has a USB port so if I connect a USB in my TAB will it work for the remote
desktop? (usb connected to the tab but should work as if its connected to remote computer -any possibility) If Yes Please Tell how to implement.
Q3) For ex. If I am connected to a remote computer and since my computer is not good for gaming and I want to use the remote computer to play games while the DVD is in my physical computer.....Is there any possibility
FINAL QUESTION : Can I connect to windows with an android or IOS devices without internet (PLEASE TELL HOW IF POSSIBLE) and I want to use my local Internet is the remote computer.
Friends whosoever has any knowledge regarding any question please answer me, help required. I will be really thankful to you .

A1- its possible to establish a remote desktop connection even if the user and remote computer in differerent countries but NOT possible without internet coonection... as you will have to use public ip of remote computer.
A2- To redirect devices and resources
Open Remote Desktop Connection by clicking the Start button , In the search box, type Remote
Desktop Connection, and then, in the list of results, click Remote Desktop Connection.
Click Options, and then click the Local
Resources tab.
Under Local devices and resources, select the devices or resources you want to redirect.
To see additional devices, or to redirect Plug and Play devices or drives and devices that you plug in later, click More.
To redirect supported Plug and Play devices, under Local devices and resources, double-click Other
supported Plug and Play (PnP) devices.
The Plug and Play devices that support redirection and are currently plugged in appear in this list.
To redirect supported USB devices, under Local devices and resources, double-click Other
supported RemoteFX USB devices. The USB devices that support redirection and are currently plugged in appear in this list.
Select the check box next to each device that you want to redirect.
To automatically redirect drives or devices that you plug in or connect to in the future, under Local devices and
resources, double-click Drives, and then click Drives
that I plug in later.
– or –
Double-click Other supported Plug and Play (PnP) devices, and then click Devices
that I plug in later.
A3 - not possible to mountDVD drive on remote desktop.
Yes you can establish remote desktop connection from android... there is an app called, Microsoft Remote desktop app, its very good , ı use it myself too...

Remote Desktop Connection Not Going To Full Screen on EIZO MX340 Monitor 1536x2048 Resolution

I am using a EIZO Rx-340 as a secondary monitor. So far I am only able to get into full screen by using Ctrl-Alt-Fn-Pause but it does not change the resolution. It does not help to move the slider to large. There is a black space at the top and bottom
of the display.

Hi,
Please take a try with the steps below:
1. Start "Remote Desktop Connection".
2. Click on "Options".
3. Click on the "Display" tab.
4. On "Display configuration" settings, you can change the "Remote Desktop Connection" display by moving the slider from "Small to Large".
5. By moving the "Slider" all the way to large, the display settings will automatically set to "Full Screen".
Here is the screenshot:
Also please take a check if the monitor itself is configured well.
Hope this may help
Best regards
Michael Shao
TechNet Community Support

Can 1 instance of Windows 8.1 ENTERPRISE host multiple Remote Desktop connections?

I am shopping for the components for building a machine with fair, high-performance hardware. I have Windows 8.1 Professional. I wanted to know if either Windows 8.1 Professional or Windows 8.1 Enterprise can support multiple remote connections
from users outside the local network. For example, my brother is based in San Diego, CA and has an underpowered laptop. Is there any way to make a remote connection over that much distance, from San Diego to Northern Virginia, from a RDP client running Windows
8.1 Professional to a RDP "server" Windows 8.1 Professional/Enterprise machine, and run a modern, single- or multiplayer- game over smoothly that connection? At the very least, is it possible to run common
apps (e.g. Microsoft Office 2013 IE 11, Adobe Acrobat XI) smoothly on a Windows 8.1 Pro RDP client connected to a Windows 8.1 RDP "server" located 2250+ miles away?
Would upgrading my installation from Professional to Enterprise improve the responsiveness and display quality for my remote users?
I know Windows Server R2 2012 has features specific for handling remote connections, but I am trying to keep a Windows 8.1 user experience. Still, if anyone can show some evidence that Windows Server 2012 R2 Remote Desktop Services (RDS) improves display
and responsiveness over long-distances for remote (RDS) connections, then I will shop for Windows Server 2012 R2 Standard instead. The huge drawback of Windows Server 2012 R2 Standard CALs is the enormous cost to enable 3-5
remote connections for family, non-commercial use.
Has anyone attempted to host long-distance remote access, non-commercially, for 3-5 connections? Has it worked well? What, in general, is required?
T. Webster

Hi,
It depends on the quality of the network connection to run the software smoothly throuth RDP. And I don't think the quality would be better if you upgrade to Windows 8.1 Enterprise.
Windows 8.1 allow only one session of RDP, the Remote Desktop Server in Windows other than the Windows Server edition has a limitation to allow only one concurrent user per session by default, i.e. if someone remotely connects to the computer over RDP then
whoever was logged in at that moment will be automatically logged off, even if that user is physically present at the computer. This is by design.
Regarding more information about RDP, please take a look at the following articles:
Remote Desktop app help
Remote Desktop Connection: frequently asked questions
Best regards
Michael Shao
TechNet Community Support

Installed the RDS 2012 Server License per user CAL (5pcs) after not allow over two users remote desktop connection problem

I have successfully to installed the RDS 2012 Server R2 per user CAL (5pcs) Open License after is found not allow over two users to remote desktop connection on this Server problem, I try to uninstall the license and then (internet on-line & telephone
call Microsoft Activate Center get the activate key) to reinstall is still same of the result on below problem.
Select a user disconnect so that you can sign in.
There are too many users signed in
User1 Active
User2 Active
() Force disconnect of the user

Hi,
In addition you can also refer following article for RDL configuration.
RD Licensing Configuration on Windows Server 2012
http://blogs.technet.com/b/askperf/archive/2013/09/20/rd-licensing-configuration-on-windows-server-2012.aspx
Hope it helps!
Thanks.
Dharmesh Solanki
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Firefox 7.0.1 crashes over Remote Desktop Connection

Firefox has been crashing very often over a Remote Desktop Connection in Windows 7 (Client: Windows XP, Host: Windows 7). The problem used to occur infrequently before, but has worsened since the last few updates.

I do not have a crash ID because Firefox just freezes (hourglass on the window) and then I have to kill the process from Task Manager in Windows 7. No message, no IDs, just freezes. Then Firefox starts with the "Oops this is embarrassing" message, asking which tabs to restore. This happens randomly when accessing sites like Facebook and YouTube and playing videos.
Can I check the log to see if there is a crash ID?

Remote Desktop Connection Manager can only open 6 sessions at a time on Server 2012

I am only able to open, and view thumbnails, for a maximum of 6 RDP sessions on my Server 2012 box at a time in Remote Desktop Connection Manager (RDCM). If I add more sessions I just get a variety of connection errors for the additional sessions. If I activate
a 7th session one of the existing 6 sessions goes off-line with a connection error message. Sometimes the error says 3334, sometimes the error says 0x8345000E, and sometimes it just says there is a connection error.
I have checked Group Policy on the server to ensure I don't have any settings restricting the number of RDP sessions.
In fact, I will often have 30 or 40 RDP simultaneous sessions opened, I am just not able to view them all in RDCM. I have seen reviews of RDCM with screenshots showing dozens of thumbnails so it seems to be something that's possible to do.
Are there any settings I should make on the server to allow RDCM to connect to more than 6 simultaneous RDP sessions?
Just to be clear, all these RDP sessions are running on the same server. Also, I am just using the trial license for Server 2012 and Remote Desktop Services right now. I don't think that should have an impact, but I wanted to be thorough.

Thanks Jakub for "corflags" info.
Unfortunatelly it doesn't work because running mRemoteNG.exe process in 64bit can't load MSTSC ActiveX component (referenced assemblies) because original files were assembled from 32bit dll [mstscax.dll]?
Error message when making RDP connection:
Could not load file or assembly 'Interop.MSTSCLib, Version=1.0.0.0, Culture=neutral, PublicKeyToken=null' or one of its dependencies. An attempt was made to load a program with an incorrect format.
I was able to create new AxInterop.MSTSCLib.dll and Interop.MSTSCLib.dll assemblies from 64bit dll version and now it works with "AnyCPU":-)
http://www.filedropper.com/axinteropmstsclib-mremoteng
Using AxImp.exe and TlbImp.exe didn't worked for me because it creates assemblies in wrong namespace "MSTSCLib" instead of "Interop.MSTSCLib" (AxImp.exe) and TlbImp.exe for changing namespace generated many "marshaled errors"
so final .dll wasn't working.
Adding MSTSCAX.dll reference in Visual Studio directly created correct and functional assemblies. Who don't know how to create 64bit compatible assemblies or don't have Visual Studio, feel free to check linked file.
Hope it helps
P.S. Sorry for possible technical misinterpretation, I am not programmer so creating new assemblies was trial-error process...

Remote desktop connection manager on windows 8.1, can't connect to windows server 2012 R2, Socket closed

remote desktop connection manager on windows 8.1, can't connect to windows server 2012 R2, Socket closed each time i try to open remote connection to the server,
does remote desktop connection manager V2.2 not compatible with windows 8.1, and if so, is there are any other compatible versions
or what's the problem,
Mahmoud Sabry IT System Engineer

this issue maybe will be fix by latest version, we still waiting for it
maybe your issue can be fix using this methods
https://social.technet.microsoft.com/Forums/windowsserver/en-US/61f218a5-5ef8-49da-a035-90cdd64fc9a0/problem-with-remote-desktop-connection-manager-error-3334?forum=winserverTS
http://shawn.meunier.com/?p=1#comment-43

Remote Desktop Connection Times Out With "Can't Connect" From One Specific Computer Only

This is an odd one... I manage several servers from this computer. This particular server, 2012 Essentials, won't allow for remote desktop connections to either the server or attached workstations. I can get into the server's remote web page but when I
attempt a remote desktop connection, it hangs on "Initiating remote connection..." and then times out with the error response that remote desktop can't connect. But... if I attempt the same connections from any other computer, I am able to get in
and utilize remote desktop. Does this mean that there is a certificate issue with the computer unable to connect and if so, how does one remedy this? Or is it some other issue? I've attempted everything within my technical ability to no avail. Any suggestions
are greatly appreciated.

Hi,
Before going further, would you please let me know the RDC version that used in the problematic computer? Was it the same with other computers?
Please temporarily disable firewall and then check if this issue can be solved. Based on your current description, it’s hard to say the root reason of this issue.
So, I suggest that you should check relevant log files and get some clues. It will help us to narrow down and solve your issue.
Hope this helps.
Best regards,
Justin Gu

I have a time capsule connected directly to fiber connection. I have connected a windows server directly to TC and configured it for remote desktop connection. From my interanet I can access srvr but not from my home. What config I need on TC?

I have a time capsule directly connected to fibre optic point out. All pcs and macs are connected wirelessly to the internet. I have connected a windows server pc to TC. When configured for Remote desktop connection, I can access windows server from within interanet but don't know how to access it from internet. I guess I need to change some settings in TC to get some ip adress for the remote desktop connection from my home. Anyone who can help me out? Appreciate it.
Narmin

I am a little lost now.. I have read again your title and your first post.. and they seem inconsistent.
In the title you state.
From my interanet I can access srvr but not from my home.
Interanet is not a word I know.. I assumed intranet...are you talking about internet or intranet? And just to be clear say WAN or LAN.. !! Is your home part of the interanet??
In the first post you state,
I can access windows server from within interanet but don't know how to access it from internet.
Now this is more normal.. the issue is not in the home at all, it is accessible from there but fails from internet. If this is correct, then you can do a few obvious things to determine where the problem is.
But first I need to know are you actually testing from a different internet connection to your home lan.. you are not just trying the public IP from inside the LAN as that will fail due to the TC not doing NAT Loopback.
I am also assuming the TC is the only router in the network, and has the public IP on the WAN interface.
And I am also assuming you have turned on the ping responder and you can actually ping your public ip from the internet and get a response. This helps no end in figuring out where there are issues. Strange but I have no idea if there is a ping responder in the TC WAN so you might need to forward that as well. Also if you have a dynamic public ip address are you using dyndns or no-ip or some other service to connect.
1. Test bypassing the TC.. plug the internet connection straight into the windows server,, and test if you have access. If yes, the TC is the problem.. if not, your setup on the windows server is wrong.. look at firewall in particular.
2. Assuming from test 1 the TC is the problem, Post the screen shots of the port forwarding setup for us to look at.. that is by far the easiest way to check it out.
There are lots of references to port forwarding in the TC.. eg
http://must-know-mac.blogspot.com/2008/07/how-to-port-forward-time-capsule.html
The things that generally go wrong are firewall on the computer that is accepting the port.
The ISP doesn't allow connections on a particular port. (not likely in your case)
The router is behind another router.. double NAT will kill any port forward.
Upnp has already allocated a port.. not an issue as TC doesn't use upnp although a reboot of everything after you set port forwards is well worth it.. amazing how things don't stick properly without a reboot.
IP on the receiving device is not static and so changes.
Not enough or right type of ports are opened. This is always messier than it looks as one port is often not enough for two way communications.

Can't connect to windows 7 machine using microsoft remote desktop connection

I am unable to connect from my home network to the Windows 7 Professional machine at my office, using either Microsoft Remote Desktop Connection (2.1.1) for Mac or the open source CoRD program.
When connected to the office network (which is running MS Small Business Server 2011 Standard) both CoRD and MS RDC will connect to my desktop machine just fine! (My MacBook Pro runs Mountain Lion.)
From my home network, MS RDC will complain that it cannot find the Windows computer if I just use the Windows computer name. If I use the Windows machine's iPV4 address, it works on it for a minute and then tosses up this error message:
Using the IP address of the Windows machine, CoRD just grinds away for a minute or so and then times out.
I should add that using Internet Exporer under Parallels from home, I can get a little closer to success (after fidding around with ActiveX controls for a bit). I will get to the Windows login screen, but then I am told that my user password is wrong (which makes no sense at all)!
Okay, geniuses, have at it, and thanks in advance!!

The genius for Microsoft products an be found onthe Microsoft forums for their Mac software:
http://answers.microsoft.com/en-us/mac

IS at work told me I need to upggrade my home Macbook Pro operating system , 10.6.8, to a new version in order to remote desktop connect to my windows 7.1 machine at work. I want to know if I can skip prior upgrades and go to Yosemite or if I have

Since my work machine was upgraded to a Windows 7.1 pc, I can no longer connect remotely with my Macbook Pro with 10.6.8. I need to know the most efficient and economical way of doing this and if I can skip versions to get where I need to be. Supposedly, I need the very latest remote desktop connection software, and it is not compatible with 10.6.8. Help please.
Thanks

Open the Mac App Store and try downloading Yosemite. If you get told it's incompatible, choose About this Mac from the Apple menu, check if the computer has at least a Xeon or Core 2 Duo(not Core Duo) CPU and 2GB of RAM, and if it does, click here and order a download code for Lion 10.7.
Back up your data and check your applications for compatibility before upgrading. In particular, Mac OS X 10.7 and newer don't support PowerPC programs such as versions of Microsoft Office prior to 2008.
(119310)

WRV210- Can't establish Remote Desktop Connection over IPSec

Similar Messages

Maybe you are looking for