Configure iSCSI multipath in OVM 3.1.1 with storage plug-in not possible ?
I have a configuration with 4 iSCSI paths to storage system. All is working fine if the discover and login
process was performed manual. Multipath is working well with 4 paths.
# iscsiadm -m session
tcp: [13] 192.168.10.1:3260,25 iqn.2000-09.com.fujitsu:storage-system.eternus-dx400:CM0CA3P0
tcp: [14] 192.168.20.1:3260,26 iqn.2000-09.com.fujitsu:storage-system.eternus-dx400:CM0CA3P1
tcp: [15] 192.168.10.2:3260,27 iqn.2000-09.com.fujitsu:storage-system.eternus-dx400:CM1CA3P0
tcp: [16] 192.168.20.2:3260,28 iqn.2000-09.com.fujitsu:storage-system.eternus-dx400:CM1CA3P1
# multipath -ll
3600000e00d10000000100000000c0000 dm-2 FUJITSU,ETERNUS_DX400
size=30G features='1 queue_if_no_path' hwhandler='0' wp=rw
|-+- policy='round-robin 0' prio=50 status=enabled
| |- 25:0:0:1 sdg 8:96 active ready running
| `- 26:0:0:1 sdi 8:128 active ready running
`-+- policy='round-robin 0' prio=10 status=enabled
|- 27:0:0:1 sdk 8:160 active ready running
`- 28:0:0:1 sdm 8:192 active ready running
I want to configure iSCSI multipath in OVM manager using specific storage plug-in.
I proceed “Discover SAN Server” with following parameter:
Name: Storage-Name
Storage Type: iSCSI Storage Server
Storage Plug-in: Fujitsu ETERNUS
Admin Host: IP-Addr. of storage system
Admin Username: user name to access storage system
Admin Password: password
Access Host (IP) Address: 192.168.10.1
After this configuration I see my storage system and assigned physical volumes to an access group.
Now the volumes are available on the OVM storage server, >>>> but I lost the multipath functionality <<<<<.
# multipath -ll
3600000e00d1000000010000000120000 dm-1 FUJITSU,ETERNUS_DX400
size=30G features='1 queue_if_no_path' hwhandler='0' wp=rw
`-+- policy='round-robin 0' prio=50 status=active
`- 33:0:0:1 sdd 8:48 active ready running
The reason for this behavior is that only one Access Host (IP) Address can be specified.
With this IP address a session was established … but only 1 session and not 4 !!
How can I specify the remaining 3 paths to have proper multipath functionality?
I know that Citrix XenServer accepts more Access Host (IP) Addresses,
e.g. 192.168.10.1,192.168.10.2,192.168.20.1,192.168.20.2
Thanks for help.
@user12273962
Yes, you are right. The storage plug-in is for management of the storage within OVM.
This is working well, but I'm still missing the multipath fuctionality. This storage plug-in is not responisble
for establish the multipath, but OVM should take care of this.
@budachst
Yes, OVM did only open one session and loggin only to one target, because only one Access Host (IP) Address: 192.168.10.1
can be specified.
# iscsiadm -m session
tcp: [21] 192.168.10.1:3260,25 iqn.2000-09.com.fujitsu:storage-system.eternus-dx400:CM0CA3P0
In my point of view it is not possible to configure the remaining targets, so this is a design problem.
Any new inputs and informations are welcome.
Similar Messages
-
ESX 5.1 and iSCSI multipathing
Hello.
I have a problem in configuring vSphere Cluster with iSCSI multipathing.
Host in cluster have four physical interfaces. Host have four vmk interfaces for iSCSI, which mapped to individual physical interface.
Storage is IBM Storwize 3700 with four configured targets (10.78.2.2 - 10.78.2.5).
Why I see only 4 paths to storage? I think there should be 16, I am right? (4if from storage * 4if from host).
Rescan HBA not resolve this problem.
P.S. All paths on storage work properly on another host not in cluster.Actually found the reference , its in the firmware upgrade guide itself:
All connectivity may be lost during firmware upgrades if you have configured both Enable Failover on one
or more vNICs and you have also configured NIC teaming/bonding at the host operating system level. Please
design for availability by using one or the other method, but never both.
Is this still valid? Whats the setting to be done on ESX nic teaming if we wanna use Enable failover on UCS? -
OVM 3.3.1: NFS storage is not available during repository creation
Hi, I have OVM Manager running on a separate machines managing 3 servers running OVM server in a server pool. One of the server also exports a NFS share that all other machines are able to mount and read/write to. I want to use this NFS share to create a OVM repository but so far unable to get it to work.
From this first screen shot we can see that the NFS file system was successfully added under storage tab and refreshed.
https://www.dropbox.com/s/fyscj2oynud542k/Screenshot%202014-10-11%2013.40.00.png?dl=0
But its is not available when adding a repository as shown below. What can I did to make it show up here.
https://www.dropbox.com/s/id1eey08cdbajsg/Screenshot%202014-10-11%2013.40.19.png?dl=0
No luck with CLI either. Any thoughts?
OVM> create repository name=myrepo fileSystem="share:/" sharepath=myrepo - Configurable attribute by this name can't be found.
== NFS file system refreshed via CLI ===
OVM> refresh fileServer name=share
Command: refresh fileServer name=share
Status: Success
Time: 2014-10-11 13:28:14,811 PDT
JobId: 1413059293069
== file system info
OVM> show fileServer name=share
Command: show fileServer name=share
Status: Success
Time: 2014-10-11 13:28:28,770 PDT
Data:
FileSystem 1 = ff5d21be-906d-4388-98a2-08cb9ac59b43 [share]
FileServer Type = Network
Storage Plug-in = oracle.generic.NFSPlugin.GenericNFSPlugin (1.1.0) [Oracle Generic Network File System]
Access Host = 1.2.3.4
Admin Server 1 = 44:45:4c:4c:46:00:10:31:80:51:c6:c0:4f:35:48:31 [dev1]
Refresh Server 1 = 44:45:4c:4c:46:00:10:31:80:51:c6:c0:4f:35:48:31 [dev1]
Refresh Server 2 = 44:45:4c:4c:47:00:10:31:80:51:b8:c0:4f:35:48:31 [dev2]
Refresh Server 3 = 44:45:4c:4c:33:00:10:34:80:38:c4:c0:4f:53:4b:31 [dev3]
UniformExports = Yes
Id = 0004fb0000090000fb2cf8ac1968505e [share]
Name = share
Description = NFS exported /dev/sda1 (427GB) on dev1
Locked = false
== version details ==
OVM server:3.3.1-1065
Agent Version:3.3.1-276.el6.7Kernel Release:3.8.13-26.4.2.el6uek.x86_64
Oracle VM Manager
Version: 3.3.1.1065
Build: 20140619_1065Actually, OVM, as is with all virtualization servers, is usually only the head on a comprehensive infrastructure. OVM seems quite easy from the start, but I'd suggest, that you at least skim trough the admin manual, to get some understanding of the conecpts behind it. OVS thus usually only provides the CPU horse power, but not the storage, unless you only want to setup a single-server setup. If you plan on having a real multi-server setup, then you will need shared storage.
The shared storage for the server pool, as well as the storage repository can be served from the same NFS server without issues. If you want to have a little testbed, then NFS is for you. It lacks some features that OCFS2 benefits from, like thin provisioning, reflinks and sparse files.
If you want to remove the NFS storage, then you'll need to remove any remainders of any OVM object, like storage repositories or server pool filesystems. Unpresent and storage repo and delete it afterwards… Also, I hope that you didn't create the NFS export directly on the root of the drive, since OVM wants to remove any file on the NFS export and on any root of ony volume there's the lost-found folder, which OVM, naturally, can't remove. Getting rid of such a storage repo can be a bit daunting…
Cheers,
budy -
How do I configure my Airport Extreme to see the printer I have plugged into the USB port?
How do I configure my Airport Extreme to see the printer I have plugged into the USB port?
OK. The 6.0 version no longer has a printer configuration that I could find. You might try Printer Sharing in the Sharing preferences.
I would also check the printer's user manual for help with the setup, and that failing check the manufacturer's website and/or tech support. -
I like it that I can save webpages with or without dependencies in a separated folder. And its implementation in Firefox (e.g. it remembers how I saved something before, and that way becomes the default) can also be good sometimes. But usually it is not.
Usually I want to save pages as HTML-only. Sometimes, but only sometimes I have to save a page as a whole (I don't know the name of the feature). But after I save something with dependencies, I often forget that, and don't care about this option. Firefox, however, doesn't forget it, and saves thousands of unimportant images, until I notice it and switch it off again.
This is not good.
I tried Google Chrome, which simply don't remember how I saves something before, and always select the complete page option for default. It is exactly the opposite of the perfect solution (in my opinion). The best would be if the browser would save everything as HTML only, if I don't change it. Or it would be even better if I could configure it manually (turn this remembering feature on/off).
This is not a beginner's problem, so it would be good if only a config option solved this. I imagine that already exists a config option for this, but I could not find it. I found only the "browser.download.save_converter_index" option, which depends on how I used it last time.
Is there a config option for this? Or should I report this in the Firefox brainstorm page?
Thank you for your time
D. J. S.That choice is remembered in the Integer pref <b>browser.download.save_converter_index</b>
0: Web Page, complete (default)
1: Web Page, HTML only
2: Text files
If you want to reset that choice to HTML only on every start of Firefox then you can use this line in the file [http://kb.mozillazine.org/user.js_file user.js]
<pre><nowiki>user_pref("browser.download.save_converter_index", 1);
</nowiki></pre>
See also http://kb.mozillazine.org/Editing_configuration#How_to_edit_configuration_files -
I am trying to consume a base model which is available in the Customer.jws (AppCmmnCompActivitiesPublicModelActivityManagement) to my Mobile UI project available in Sales.jws (SalesMobilePublicUi). We have added proper Databindings.cpx entry for accessing the applicationModule present in the model.
On deploying the sales mobile app, I get the following ConfigException:
JBO-33001: Configuration file /oracle/apps/crmCommon/activities/activityManagementService/applicationModule/common/bc4j.xcfg is not found in the classpath.
The bc4j.xcfg mentioned in the above path actually contains the entry. On checking about this issue, I found out that the prominent solution would be model project should be added as Dependencies to the UI project. But the UI is in different workspace (Sales.jws) and so the list of dependencies shown are those of this workspace only, whereas the model is present in Customer.jws and it does not come under the dependencies list.
How can this issue be resolved? Please let me know any pointers on solving this issue.Build an adfLibrary from the model in the Customers.jws and add this adfLibrary to the other ui project. This will get you the dependency.
Timo -
Configure New TM on a New Macbook pro with retina display Issue
I have bought a new New Macbook pro with retina display laptop (Lion moutain OS)and a new TM (2TB).
I have an internet router with wireless connect.
I plugged TM to the router with an ethernet cable.
Connect my TM to my macbook with an ethernet cable.(at this point I still cannot see TM on my Mac)
then I choose Time capsule from WiFi as shown below:
Then the airport utility (version 6.1) opened and start configuring TM but it gives an expected error when it is starting to join the TM!!!!
I have reset the TM several time but with no hope.
PS: I can configure the same TM on a normal laptop with windows 7 installed and Airport utility 5.6
I am struggling on this issue for weeks and I cannot yous TM on my macbook pro.
Help please.Time Capsule .. TC is the hardware box you bought.. Time Machine is the software you use in the Mac computer.. so what you generally refer to as TM is really TC.. !!
I can configure the same TM on a normal laptop with windows 7 installed and Airport utility 5.6
That is great.. you do not need to setup the Time Capsule at all then. It is already setup.. forget using 6.1 utility.. it is useless toy version.
Just use it.. open Time Machine and see if you can connect to the TC drive to do backup.. and to the wireless.
From your statements..
Connect my TM to my macbook with an ethernet cable.(at this point I still cannot see TM on my Mac)
You are trying to connect with both wireless and ethernet at once.. This can mess things up. choose wireless or ethernet.. not both.
If you keep running into issues.. reset the TC.. I know yet again.
Set it up using SMB names.. for both the TC itself and wireless.
Then lock the wireless channel for 2.4ghz.. use channel 1, 6, or 11 (13 in europe) and see how it goes. -
I'm getting this error and is there any way to resolve this without re-creating the service/s again, etc. Just curious if there are any suggestions/steps I may have missed, if not, I'll drop and recreate the services again
Anyway, I have a backup of the emkey.ora and put it in the sysman/config directory, but still doesn't work... please see below...
C:\Documents and Settings\abigail>emctl status emkey
Oracle Enterprise Manager 11g Database Control Release 11.2.0.1.0
Copyright (c) 1996, 2010 Oracle Corporation. All rights reserved.
Please enter repository password:
The Em Key is not configured properly or is corrupted in the file system and doe
s not exist in the Management Repository. To correct the problem:
1) Copy the emkey.ora file from another OMS or backup machine to the OH/sysman/c
onfig directory.
2) Configure the emkey.ora file by running "emctl config emkey -emkeyfile <emkey
.ora file location>".
C:\Documents and Settings\abigail>emctl config emkey -emkeyfile E:\app\abigail\p
roduct\11.2.0\dbhome_1\sysman\config
Oracle Enterprise Manager 11g Database Control Release 11.2.0.1.0
Copyright (c) 1996, 2010 Oracle Corporation. All rights reserved.
Please enter repository password:
The Em Key is already configured. To override the current configuration, run "em
ctl config emkey <options> -force".
C:\Documents and Settings\abigail>emctl config emkey -emkeyfile E:\app\abigail\p
roduct\11.2.0\dbhome_1\sysman\config -force -sysman_pwd ********
Oracle Enterprise Manager 11g Database Control Release 11.2.0.1.0
Copyright (c) 1996, 2010 Oracle Corporation. All rights reserved.
The Em Key could not be configured. Unable to access file E:\app\abigail\product
\11.2.0\dbhome_1\sysman\config.
C:\Documents and Settings\abigail>emctl secure dbconsole -sysman_pwd ********
Oracle Enterprise Manager 11g Database Control Release 11.2.0.1.0
Copyright (c) 1996, 2010 Oracle Corporation. All rights reserved.
http://ABIGAIL:5501/em/console/aboutApplication
DBCONSOLE already stopped... Done.
Agent is already stopped... Done.
Securing dbconsole... Started.
Please enter repository schema password:
Securing dbconsole... Failed.
EMKey is misconfigured.Sorry but I'll have to ignore your suggestion, and don't worry about how I spend my time
AND OHMYGODD IT WORKSS!!! For future reference, this is how I solved it based on my searches, actually based on one particular search:
http://franjv.blogspot.com/2013/08/emkey-problems-in-oracle-rac-11gr2.html
Thank youuu whoever wrote that and... is it the same "Fran" who helped me the last time?!? Coincidence??
ANyway, thank youuuu -
"Configuration not possible for material PC-2011 : Reason 3"
Hi any MM guys,
Please help me to solve the following thread.
"Configuration not possible for material PC-2011 : Reason 3 --> Help
Message no. V1360"
Thanks and regards
D.Srinivasa raoI believe you are trying use Sales order for services....and you have created material in services if I am not wrong.
Again sticking to basic rules, you can configure only materials with type KMAT. Further for services, I believe there is a concept called milestone billing...which I am not sure about.
Chk SAP notes, 625092, 26187
BR,
Krishna -
I want to install xp on my MacBook Pro with i5 processor, but that creates the partition and restart the computer just stays in the following message: The Setup is inspecting your hardware configuration of your computer, someone can help me with this ?
The answer has not changed since your last post here https://discussions.apple.com/thread/3230576?tstart=0
There are no XP or Vista drivers for the new Apple computer hardware. Apple stopped XP and Vista support. http://support.apple.com/kb/HT4410. -
Configuration not possible in mto process
hi
i am getting a error message configaration not possible for reason:3 when i am saving the sales order in make to order process.
Can anyone please answer this question.
regards
arunDear Arun
Probably, you would be trying to create a sale order for configurable material the settings for which has not been done properly.
Go through the link and check whether your settings are in line with the link
[Material Master Data for Configurable Materials |http://help.sap.com/saphelp_46c/helpdata/en/92/58c09b417011d189ec0000e81ddfac/frameset.htm]
Thanks
G. Lakshmipathi -
hi
i am getting a error message configaration not possible for reason:3 when i am saving the sales order in make to order process.
Can anyone please answer this question.
regards,
venkatDear Pingali
Check whether your configuration is in line with this link
<a href="http://help.sap.com/saphelp_47x200/helpdata/en/e0/71bb1f9c9f11d191920000e8a5f6e6/content.htm">Make To Order Sample Scenario</a>
Thanks
G. Lakshmipathi -
Hi,
I have another problem - after upgrade ios wirelles connection not work.
After reload i have :
Configuration of subinterfaces and main interface
within the same bridge group is not permitted
STP: Unable to get the port parameters.
Please configure the bridge group on this interface first.
Please configure the bridge group on this interface first.
Please configure the bridge group on this interface first.
SETUP: new interface NVI0 placed in "shutdown" state
my old configuration work propertly in the old software, but after update i have notificatio.
Old thread:
https://supportforums.cisco.com/discussion/12379491/cisco-877w-no-wireless-connection
my current sh run:
version 12.4
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime
service timestamps log datetime msec localtime
service password-encryption
hostname cisco
boot-start-marker
boot system flash:c870-advipservicesk9-mz.124-24.T6.bin
boot-end-marker
logging message-counter syslog
logging buffered 4096 informational
enable secret 5 $1$eCNp$rWuBfZ/cexnwnkm7L447s.
aaa new-model
aaa session-id common
dot11 syslog
dot11 ssid ciscowifi
vlan 1
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 7 050D031D26595D0617
dot11 wpa handshake timeout 500
ip source-route
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.56.1
ip dhcp pool CLIENT
import all
network 192.168.56.0 255.255.255.0
default-router 192.168.56.1
dns-server 8.8.8.8 194.204.159.1 194.204.152.34
lease 0 2
ip cef
no ip domain lookup
no ipv6 cef
multilink bundle-name authenticated
username marek password 7 00121A0908500A
archive
log config
hidekeys
ip tcp path-mtu-discovery
bridge irb
interface ATM0
description Polaczenie ADSL do ISP$ES_WAN$
no ip address
no atm ilmi-keepalive
pvc 0/35
encapsulation aal5mux ppp dialer
dialer pool-member 1
hold-queue 224 in
interface FastEthernet0
description Edzia
interface FastEthernet1
description dom
interface FastEthernet2
description Dziadek
interface FastEthernet3
interface Dot11Radio0
no ip address
no ip redirects
ip local-proxy-arp
ip nat inside
ip virtual-reassembly
no dot11 extension aironet
encryption vlan 1 mode ciphers tkip
encryption mode ciphers aes-ccm tkip
broadcast-key change 3600
ssid ciscowifi
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
world-mode dot11d country AU indoor
no cdp enable
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.1
description ciscowifi
encapsulation dot1Q 1 native
no cdp enable
interface Vlan1
no ip address
bridge-group 1
interface Dialer0
description Interfejs dzwoniacy
ip address negotiated
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
dialer-group 1
ppp chap hostname [email protected]
ppp chap password 7 xxxxxxxxxxxxxxxxxxxxxx
interface BVI1
description Polaczenie dla sieci LAN
ip address 192.168.56.1 255.255.255.0
ip nat inside
ip virtual-reassembly
no ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer0
no ip http server
no ip http secure-server
ip nat inside source list 100 interface Dialer0 overload
ip nat inside source static tcp 192.168.56.10 80 interface Dialer0 80
ip nat inside source static tcp 192.168.56.10 22 interface Dialer0 22
logging trap debugging
logging 192.168.56.10
access-list 100 permit ip 192.168.56.0 0.0.0.255 any
access-list 100 deny ip any any
no cdp run
snmp-server community ciskacz RO
snmp-server chassis-id ciskacz
control-plane
bridge 1 protocol ieee
bridge 1 route ip
line con 0
no modem enable
line aux 0
line vty 0 4
exec-timeout 0 0
transport preferred ssh
transport input ssh
scheduler max-task-time 5000
end
please help - thanks!Hello Marek,
I suppose you are not planning to do any kinds of advanced config using several VLANs and multiple SSIDs so let's just make your configuration simple and working.
In short, you need to remove all references to VLAN 1 and to any subinterfaces possibly related to the VLAN 1. This means in particular (follow these steps in sequence):
Remove the Dot11Radio0.1 subinterface entirely
In the Dot11Radio0 section, remove the encryption vlan 1 mode ciphers tkip command
In the dot11 ssid ciscowifi section, remove the vlan 1 command
After performing these steps, make sure that the ssid ciscowifi and encryption mode commands are still present in the Dot11Radio0 configuration, and if not, reenter them.
Best regards,
Peter -
No Function Identifier maintained. Configuration check not possible
Dear PM team,
While doing the Equipment installation with goods movement through IE4N, transaction code, system throwing following error messages.
1. No function identifier maintained. Configuration check not possible
2. Message for the configuration check.
Please guide me where i did the mistake? and suggest me how to correct this error message, without doing the changes in message controls.
thanks & regards
JKJK,
My guess is that you are using Configuration Control.
If so, then have a look at these transactions:
PeteA -
Acquired airport Express, configured it, but how to create one that I could plug in other devices, it needs to register each new device that connects to it .... What to do?
Acquired airport Express, configured it, but how to create one that I could plug in other devices, it needs to register each new device that connects to it .... What to do?
Maybe you are looking for
-
hi ... i have downloaded the j2ee 1.5 from sun web site , but i am unable to compile a servelet programe but there is a error can not find package javax.servelet ..and i already have configured class path for jdk and other tool like javac, javap etc
-
Want to forward ports, but 'add' and 'default host' are grayed out! help!
Hey folks. Configuring my laptop to access a new airport express plugged in one floor below me. great signal connection works fine, but of course it isn't forwarding ports i want... so I go to set it up... now, the owner of the house set it up first,
-
C++ visual runtime error!
I'm really hoping you guys have an answer for me.In the last couple of days, I have been receiving a runtime error whenever i try to affect the variables in my brushes pallette. I mean any little tweak, be it the angle of the preset or even just the
-
Setting a price condition through a BAPI
Hi, I have the following problem - I am trying to set a condition on an item in a quotation using the BAPI_CUSTOMERQUOTATION_CHANGE. The error that I get back is "Requirements are not fulfilled for condition PN00". When I try to set the condition man
-
XI Installation: SAP System Account+Password- Login failed
Hi All, This is my first attempt in installing XI. I have installed SAP Web AS 6.40 ABAP+Java System and am trying to install XI now. I can also confirm that my J2EE engine is up and running. I ran the J2EE example on HTTP using port 50000. Here is m