Default configuration parameters

'Show run' don't show default configuration parameters, interface specific default parameters. It only shows manually entered commands only.
Is there any way to find out default all hidden configuration commands and values?

It's been seven years since someone else asked this question, so I'm looking for an update.
We just bought a UC560, mainly intending it as our new VoIP phone controller:
Cisco IOS Software, UC500 Software (UC500-ADVIPSERVICESK9-M), Version 15.0(1)XA2, RELEASE SOFTWARE (fc2)
Compiled Sat 06-Mar-10 04:52 by prod_rel_team
ROM: System Bootstrap, Version 15.0(1r)XA, RELEASE SOFTWARE (fc1)
Apparently it can also do routing, NAT, DHCP, and a basic firewall. I wasn't planning to use it for that, and was planning to migrate from Netware 6.5 routing/firewall to Microsoft RRAS, but I guess if this Cisco box can do it, might as well.
But I am not (yet?) a Cisco certified tech so I don't have the 1000 command line options and defaults all memorized.
If I enable DHCP, can it tell me the default address lease time? Does the Cisco DHCP ping addresses before assigning them, to avoid accidental overlaps? "show running_config" only shows what we have configured, not what the any of the defaults are..

Similar Messages

Syntax error in profile relation while retreiving configuration parameters

Trying to get our Directory Services properly functioning after an IP change. Running
# kadmin.local -q listprincs
yesterday revealed that all service principals weren't set up properly. Dig dig dig... found that I might (since this server was originally 10.3--now it's 10.4.4) try
# slapconfig -kerberize diradmin
That pointed me in the direction of using Workgroup Manager to fix a couple things with the KerberosClient record for the server. Did that. Reran the command. It complained about an improperly formatted configuration file because it wiped the contents of edu.mit.Kerberos (took out the DNS bits). Then ran
# kerberosautoconfig -u
which resulted in
MergeLoggingInfo: creating default logging info
At this point, edu.mit.Kerberos looked good. Then I tried
# /usr/sbin/kdcsetup -f /LDAPv3/127.0.0.1 -w -a diradmin -p ** -v 1 REALM
which resulted in
Contacting the Directory Server
Authenticating to the Directory Server
Creating Kerberos directory
Creating KDC Config File
Creating Admin ACL File
Creating Kerberos Master Key
Creating Kerberos Database
Syntax error in profile relation while retreiving configuration parameters
SendInteractiveCommand: failed to get pattern
Creating Kerberos Admin user
kadmin.local: Syntax error in profile relation while initializing kadmin.local interface
Adding kerberos auth authority to admin user
Creating keytab for the admin tools
kadmin.local: Syntax error in profile relation while initializing kadmin.local interface
Adding KDC & kadmind to launchd
Adding the new KDC into the KerberosClient config record
edu.mit.kadmind: Already loaded
com.apple.kdcmond: Already loaded
Finished
Now when I try
# kadmin.local -q listprincs
I get
Authenticating as principal root/admin@REALM with password.
kadmin.local: Syntax error in profile relation while initializing kadmin.local interface
And now I'm getting this in kdc.log
Feb 07 09:41:26 od.master.fqdn krb5kdc[21234](info): AS_REQ (7 etypes {18 17 16 23 1 3 2}) xx.xx.xx.xx: LOOKINGUPCLIENT: diradmin@REALM for krbtgt/REALM@REALM, Database is locked or in use--try again later
Feb 07 09:41:26 od.master.fqdn krb5kdc[21234](info): DISPATCH: repeated (retransmitted?) request from xx.xx.xx.xx, resending previous response
Help!
Thanks,
Rich
ps. The typo in the error message is MIT's, not mine. I guess their engineering departments are better than their English department.
Xserve G5 Mac OS X (10.4.4)

Look at the two config files:
/Library/Preferences/edu.mit.Kerberos
/var/db/krb5kdc/kdc.log
the Database is locked or in use message is due to a missing lock file.
Look in /var/db/krb5kdc/ for principal.kadm5.lock
Hope this gets you started
- Leland

NEW 9I RMAN: PERSISTENT CONFIGURATION PARAMETERS - INTRODUCTION

제품 : RMAN
작성날짜 : 2001-11-09
NEW 9I RMAN: PERSISTENT CONFIGURATION PARAMETERS - INTRODUCTION
===============================================================
오라클 9i 부터는 RMAN 에서 항상 사용되는 파라미터 세팅을 고정적으로 할 수 있게
되어 매번 파라미터를 주어야 하는 수고를 하지 않아도 된다.
Persistent Configuration Parameters 기능은 RMA 에 다음과 같은 변화를 주었다:
* RMAN 에서 파라미터의 디폴트를 DBA 가 커스터마이징 할 수 있게 되어 사용이 편리해졌다.
* 한번 커스터마이징한 파라미터는 모든 Job 에 적용이 된다.
* DBA 는 'BACKUP DATABASE' 명령어 하나만으로 RMAN 에서 데이터베이스 백업을 수행
할 수 있게 되었다.
* 오라클 9i 의 CONFIGURE 명령어는 RMAN 의 default setting 을 영구적으로 바꾸어 준다.
* 파라미터의 값은 컨트롤파일에 저장이 되며 필요한 경우에는 리커버리 카다로그와 맞추어
주는 과정이 필요하다.
오라클 9i RMAN 에서는는 'show' 명령어로 현재의 파라미터 세팅을 확인 할 수 있다.
SHOW show_operand [,show_operand ...];
show_operand: RETENTION POLICY |
EXCLUDE |
BACKUP COPIES |
CHANNEL |
DEFAULT DEVICE TYPE |
DEVICE TYPE |
SNAPSHOT CONTROLFILE |
ALL
'show all' 명령어로 현재의 모든 세팅을 확인 한다.
RMAN> show all;
using target database controlfile instead of recovery catalog
RMAN configuration parameters are:
CONFIGURE RETENTION POLICY TO REDUNDANCY 1; # default
CONFIGURE BACKUP OPTIMIZATION OFF; # default
CONFIGURE DEFAULT DEVICE TYPE TO DISK; # default
CONFIGURE CONTROLFILE AUTOBACKUP OFF; # default
CONFIGURE CONTROLFILE AUTOBACKUP FORMAT FOR DEVICE TYPE DISK TO '%F'; # default
CONFIGURE DEVICE TYPE DISK PARALLELISM 1; # default
CONFIGURE DATAFILE BACKUP COPIES FOR DEVICE TYPE DISK TO 1; # default
CONFIGURE ARCHIVELOG BACKUP COPIES FOR DEVICE TYPE DISK TO 1; # default
CONFIGURE MAXSETSIZE TO UNLIMITED; # default
CONFIGURE SNAPSHOT CONTROLFILE NAME TO '/beta/app/oracle/product/9.0.1/dbs/snapc
f_V901.f'; # default
이렇게 Persistent Configuration Parameters 를 세팅하기 위해서는 스크립트를 만들어
수행 하는 것이 좋다:
run {
# Use the configure commands to create your backup policy.
# When complete these will be the new persistent
# configuration parameters for RMAN in the controlfile
# of the target datbase.
CONFIGURE RETENTION POLICY TO REDUNDANCY 3;
CONFIGURE BACKUP OPTIMIZATION OFF;
CONFIGURE DEFAULT DEVICE TYPE TO DISK;
CONFIGURE CONTROLFILE AUTOBACKUP ON;
CONFIGURE CONTROLFILE AUTOBACKUP FORMAT FOR DEVICE TYPE DISK TO
'/proj/SME9i/backup/%F';
CONFIGURE DEVICE TYPE DISK PARALLELISM 2;
CONFIGURE DATAFILE BACKUP COPIES FOR DEVICE TYPE DISK TO 1;
CONFIGURE ARCHIVELOG BACKUP COPIES FOR DEVICE TYPE DISK TO 1;
CONFIGURE MAXSETSIZE TO UNLIMITED;
CONFIGURE SNAPSHOT CONTROLFILE NAME TO '/proj/SME9i/backup/snapf_prod9.f';
이렇게 스크립트를 수행 한 후에 결과를 확인 하기 위해서는:
RMAN> show all;
RMAN configuration parameters are:
CONFIGURE RETENTION POLICY TO REDUNDANCY 3;
CONFIGURE BACKUP OPTIMIZATION OFF;
CONFIGURE DEFAULT DEVICE TYPE TO DISK;
CONFIGURE CONTROLFILE AUTOBACKUP ON;
CONFIGURE CONTROLFILE AUTOBACKUP FORMAT FOR DEVICE TYPE DISK TO
'/proj/SME9i/backup/%F';
CONFIGURE DEVICE TYPE DISK PARALLELISM 2;
CONFIGURE DATAFILE BACKUP COPIES FOR DEVICE TYPE DISK TO 1;
CONFIGURE ARCHIVELOG BACKUP COPIES FOR DEVICE TYPE DISK TO 1;
CONFIGURE MAXSETSIZE TO UNLIMITED;
CONFIGURE SNAPSHOT CONTROLFILE NAME TO '/proj/SME9i/backup/snapf_prod9.f';
결과는 위와 같다.
--------------THE END------------------------------------------------------

Search button?!?!
Re: seek some good documents on Recovery MANager to start with
Aron

How to configure some of VMX file configurations / VM Configuration Parameters via vCloudDirector REST API

Hi
We need to configure some settings for VM using vCloudDirector REST API other wise which can be down in 2 following ways.
1. On VCenter -> select VM ( in Power Off Mode ) -> Edit Settings -> Options -> Advanced -> General -> Configuration Parameters
     Add row with values like below
           ethernet0.ctxPerDev = 1
2. -OR- directly login to Esxi Shell .. Open VMX file ( of the VM - which can be located in /etc/vmware/hostd/vmInventory.xml ) and add entries manually.
      Follow this KB http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1714
      for editing VMX file.
We would like to know how this can be achieved using vCloud Director REST. We are using 5.5 versions for both VCD and VCenter.
Thanks for help.
Regards,
Murali G D

This level of modification is not available via vCloud Director's API afaik. A similar question came up recently about modifying the amount of Video Memory on a VM, which you have to create some sort of custom workflow directly to vCenter/ESXi about.

How to restrict changes in Tabs: Defaults and Parameters in tcode: SU3

Good Morning Everybody.
Do you know how to restrict End Users can change data stored in Tabs Defaults and Parameters of tcode: SU3.
I was checking Authorization Objects related this transaction but I did not find a way to fix this issue.
Thanks for your comments.
Mauricio Cardozo.
BASIS Consultant.

I've been looking into this same question. I don't think there's any way to protect individual user parameters, which is what we really wanted to do, but it is possible to protect the Parameters tab as a whole while still granting access to the Address and Defaults tabs (if desired). SU3, which is usually given to all users, gives change access to all three tabs in the User Data, but to make it more fine-grained, as the last person said, take away SU3 and instead grant whatever combination of SU0, SU1, or SU2 makes sense for your organization. SU0 gives access to the Defaults tab, SU1 to the Address tab, and SU2 to the Parameters tab.
So, in your case, you would grant SU1 only, so users can change their name or phone number, etc, but not Defaults or Parameters. They won't even be able to see defaults or parameters if you do this, though.
I hope this helps.
--Matt

XI 3.0 Sender SOAP Adapter Default XI Parameters

Hi all,
I've noticed when posting to an inbound comm channel using the sender SOAP adapter that unless I specify a namespace and interface under the 'Default XI Parameters', an error is returned indicating I need to specify default values for the namespace and interface.
This doesn't make sense. I don't want to set up a new inbound comm channel for every interface for the same sender service. As long as the SOAP address location is correct, i.e. sender service and interface are specified correctly, why should I need to set a default namespace and interface? Also, what is the expected behavior of the default XI parameters? Should it override what's passed in the SOAP location string?

Hi,
I think you have to add:
Optional: xml.addHeaderLine 0
Obligatory: try to put the ; between quotation marks like:
Hope this helps.
Cheers,
Paul

Default XI parameters in 7.1, soap sender.

Hi,
I have a quick question about Default XI Parameters in Soap sender adapter in PI 7.1.
Why are they not present in PI 7.1( sender interface and sender NS )?
which are mandatory parameters in 7.0.
I was guessing that , this ways we can create a generic soap sender CC.
Does anyone have a exact answer as why it was removed?
Regards,
Venkat..

> Even in PI 7.0 we will add interface name and CC to the URL.
> 1. Do you mean that we are supposed to have NS too along with above entries?
Yes, you should add interface and namespace as it is mentioned in SAP Note 856597
> 2. What do you mean by aligning behavior of SOAP adapter with other adapters?
Other adapters (File, JMS) get interface and namespace from a sender agreement connected to a sender channel. The behaviour of the SOAP adapter was different before.
I was told by development that migrated channels from 7.0 work without any change. If this is not the case, open an OSS ticket for this.
For new channels you have to call the SOAP adapter always with interface name and namespace. The online help is not correct.
Regards
Stefan

JSF 1.2 web.xml configuration parameters

Actually, I know these JSF 1.2 web.xml configuration parameters:
javax.faces.CONFIG_FILES
javax.faces.DEFAULT_SUFFIX
javax.faces.LIFECYCLE_ID
javax.faces.STATE_SAVING_METHOD
Are there any more available?
(I have to study its performance implications in conjunction with RichFaces ones).

The JSF 1.2 specification document would contain the information you're looking for.

HT4505 Is it possible to save default scan parameters for Preview?

When I open Preview, the default scan parameters are stupid: text/custom size/jpeg. I want Preview to remember my usual settings and just open with those. Is that possible?
Preview 7.0
OSX 10.9.1
MacBook Pro
2.4 GHz Intel Core 2 Duo
4 GB Memory

Yep, download and install Aperture 2.1.
Select an adjustment that is already showing, and click on the small "gear" menu in the upper right hand corner of the adjustment and either choose "Remove from Default Set" or "Add to Default Set", whichever you want. From each new image selection onwards that setting will dictate if the adjustment shows or not.

Setting Default Configuration in 1.4.2

Previous versions of Java Web Start had a default configuration file javaws.cfg which contained the default preferences. When JWS was installed on PCs in our intranet, we could switch the cfg file to one which, amongst other things, set the proxy correctly and disabled shortcut creation. Then when any other user logged on to the PC, they would get a copy of this cfg file.
But in JWS 1.4.2 there no longer seems to be a default cfg file. When a user logs on they get defaults which are incorrect for our environment. This is a problem when several different users share the same PC. Whenever a new user logs on to the PC and uses Java Web Start, we must set up the preferences manually.
Our users are in a call center and are not capable of setting preferences themselves. In fact in the past we have removed the JWS icon from the desktop because we don't want them to even know it exists. All they know how to do is click a link (to a jnlp document) on a web page.
Is there some way to set the default preferences at install time that I've missed?
Thanks,
Simon.

Educated guesswork mostly; read over the JavaOne "whats new with web start" to get a feel for the changes yourself (http://servlet.java.sun.com/javaone/sf2003/conf/sessions/display-1486.en.jsp). Several things here will lead to internal changes. While it's location isn't likely to change (they're in the right place now - in the user profile dir) the contents, structure and config files certainly will.
Biggest single change is the unification of Java Plugin and Web Start, according to the slides this includes the merging of the applet & web start caches and configuration dialogs (it's not a big leap to assume this means merging their config files also). The new 1.5 Jar Hyper Compression format will also doubtless come into play changing the very format of the Jars getting cached. The other big change is to the security system - both opening up the sandbox model and a new central administration system will mean that the preferences on a users machine may be overridden at any time by the administrator. The cache structure itself undergos a big change with the new 'System Cache' - given that users cannot read from another users profile, this system cache will need to be stored in some shared directory elsewhere. A move that will split normal operation into a pair of active caches further obfuscates assumptions about the internal structure somewhat. This only scratches the surface here - needless to say, big changes ahead.
For the 'system cache' It'll be interesting to see how the web start team get around the default privileges assigned to a domain user under XP typically doesn't allow writing to a directory outside of their user profile folder (default privs are restricted). Similarly I'd like to see how well the new JNLP file associations work out in a similar scenario. Adding a file association requires writing to the registry; this again is typically a prohibited operation requiring local administrator rights to the machine. I hope the web start team have come up with answers to these problems and not just take the Java update line of only working while the user is logged on as a local administrator (http://www.javadesktop.org/forums/thread.jspa?threadID=184&tstart=0). This severely limits your user base to non-networked single user machines (home users), the network admins machine and windows 98 & me boxes which don't share the security model.
Finally it's not a good idea to make any assumptions about the internal layout and contents of any of Sun's undocumented services, it's always going to be prone to change without warning. Developers make changes to these at their own peril and only have themselves to blame when their code suddenly stops working.
- Richard

Load default configuration in BIOS to fix sound, caused another problem

Hey !
I have had problem to get sound in my T61, and used Lenovo support, Troubleshooting, to fix it.
I did as it told in Lenovo Support.
In BIOS Setup utility menu setup I pressed F9.
Then I selected YES to load the default configuration.
After that I pressed F10 key and YES to save the configuration.
But after that when I start the computer it says that a failur has occured, and windows has shot down to avoid problems with the computer.
Is there any way of going back in the BIOS setup, so I should get it work again ?
Thanks in advance/ Kurt
Moderator edit: Subject edited for clarity.

Hi !
I solved it with money !
I went to a company, and they fixed it, Don't ask me how ! I did not understand when they described it.
Anyway I have another problem with the sound, as you can see in the other message !
They tried to fix that to, but could not solve the problem.
George

Report program to find the configuration parameters of the system?

Hi,
Is there any standard program in SAP to find out the configuration parameters or the configuration settings of the system and any program to find the configuration settings across systems?
thanks & regards,
siddhartha.
P.S : Points will be rewarded.

Can you concretize your question ? For what purposes ? The "system" is the front-end or server where sap are installed? Chek the RZ20 and ST06. Regards.

Showing RMAN configuration parameters 8.1.7

Hi group
What is the RMAN command in 8.1.7 to show RMAN configuration parameters, I know (SHOW ALL;) command is used in 9i version but it doesn't work on 8.1.7.
Thanks you very much

If I remember correctly, you could NOT configure and preserve parameters in 8.1.7 (so CONFIGURE and SHOW are not present in 8.1.7 RMAN).
You could create scripts with all the required commands and save them to the OS or to the Catalog -- preferably at the OS level so that they can be viewed and edited if the Catalog becomes unavailable.
Hemant K Chitale

MS ssis service: registry setting specifying configuration file does not exist. attempting to load default configuration file. SQLIService100 - event id 274

window 2008 R2 server ---- after installing SQL 2008 R2 then applying sp2 / sp3 I noted a warning -
Note this server had SQL 2008 R2 uninstalled previously.
MS ssis service: registry setting specifying configuration file does not exist. attempting to load default configuration file.
SQLIService100 - source
event id- 274
user - N/A
Task category - service control.
Do we need to fix something and how do we fix this warning event?
dsk

You could search online for this warning. I was able to find http://superuser.com/questions/346264/event-log-warning-registry-setting-specifying-configuration-file-does-not-exist
where the fix is "in your registry, go to:
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\MSDTS\ServiceConfigFile
or
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Microsoft SQL Server\100\ServiceConfigFile
if value is empty then add in:
C:\Program Files\Microsoft SQL Server\100\DTS\Binn\MsDtsSrvr.ini.xml"
Arthur
MyBlog
Twitter

Hiding default report parameters in XLS template& password for analyzer

Hi,
I created a xls report in that report i don't have any parameters.But when i open that xls template i am getting the default Report Parameters at the top of the report
with a column1(under this we have a drop down with options All,Top10,Custom...) like this
When i open the Excel Analyzer from xls(Alt+F11) when i double click on the excelAnalyzer its asking password what is the default password??
If any one knows please share it!!
Thanks,
Saichand.V
Edited by: saichand on Jun 26, 2009 4:34 PM

See the following document on creating a workbook template with an image: [http://www.researchsummary.ca/bw/Sample_Ch10.pdf]
In BW, there is a table that stores the default workbook. The following snippet of code allows you to identify a custom workbook template as the default template for all end users.
*& Report Z_SET_BEX_USER_TEMPLATE *
*& Program to update all user's default template *
REPORT Z_SET_BEX_USER_TEMPLATE.
TABLES: rsrwbtemplate,
        usr01.
PARAMETER: wbid LIKE rsrwbindex-workbookid.
SELECT
FROM
usr01.
MOVE: usr01-bname TO rsrwbtemplate-templateuser,
        wbid TO rsrwbtemplate-workbookid = wbid.
UPDATE
    rsrwbtemplate.
IF sy-subrc 0.
    INSERT
      rsrwbtemplate.
ENDIF.
ENDSELECT.

Default configuration parameters

Similar Messages

Maybe you are looking for