I updated the IPAD with the latest update and now when I turned on and I get the Itunes log and nothing elser
I updated the IPAD with the latest update and now when I turned the IPAD on, I get the itunes logo and then nothing else. How can I fix this to let me use my IPAD?
Hi ....
"I get the itunes logo and then nothing else"
Use Recovery Mode > If you can't update or restore your iPhone, iPad, or iPod touch
Similar Messages
-
My backup got interrupted and now when I try to backup I get the following message: The backup disk image “/Volumes/Data/Macintosh.sparsebundle” is already in use. What should I do so that I can start backing up again?
1. Restart your MBP and try the back up again. If this fails try step #2 below
2. Unplug your Time Capsule from the AC giving it thirty seconds or so to discharge, plug it back in and retry the back up again once you're back online.
3. if step #1 and #2 fails, go here:
http://pondini.org/TM/C12.html -
When I send a message to the ipad, from my iphone, I get the same message to my phone from my own number. He also gets one to his iphone when he sends me a message from his ipad. I know this has something to do with the apple id; we do use the same one. Is there a way to turn off the multiple messages? We don't want to get separate apple ids because the guy at the apple store told us we wouldn't be able to share the music we have....meaning music on my id wouldn't show up with the music on his id in our itunes. So we switched to using one account. Is there a way to fix this problem without having to create a separate apple id?
Apple ID cannot be merged or transfered.
Read this tips
iOS 5 & iCloud Tips: Sharing an Apple ID With Your Family -
I updated the IPAD with the latest update and now when I turned the IPAD on, I get the itunes logo and then nothing else. How can I fix this to let me use my IPAD?
YOU ARE IN RECOVERY MODE
1. Turn off iPad
2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
3. Plug USB cable into computer's USB port
4. Hold Home button down and plug the other end of cable into docking port.
DO NOT RELEASE BUTTON until you see picture of iTunes and plug
5. Release Home button.
ON COMPUTER
6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
7. Select "Restore iPad"...
Note:
1. Data will be lost if you do not have backup
2. You must follow step 1 to step 4 VERY CLOSELY.
3. Repeat the process if necessary. -
What's the go with this latest update. Half my apps don't work and the iPad runs slower? How do I go back to the old operating system?
Make sure your apps are updated. You might try Settings > iTunes & App Store > Automatic Downloads - Updates = "On".
You cannot go back to an old operating system. -
I have just updated my ipad to 7.0.2 but now when I want to watch a download on BBC IPLAYER when I am off line it will not play the download.
I can only watch the download when I am on line . The funny thing is I can watch it then if I turn off my modem untill I shut down my i pad . Before the update I didnt need to be conected to watch my down load . Can any one help please ?Here you are "the strange draft logos"...
-
Last night I did an update and now when I turn on my macbook it just goes to the white screen with the apple and stays like that. How do I fix this issue?
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
i was updating to ios7 and my phone turned off and now it wont turn back on. it shows the apple sign but it slowly fades away and so on. Help!
Hello there, RFJA2211.
The following Knowledge Base article offers up some great troubleshooting steps for unexpected power off of your iOS device:
iPhone: Hardware troubleshooting
http://support.apple.com/kb/ts2802
Will not turn on, will not turn on unless connected to power, or unexpected power off
Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion. Learn about LCIsand corrosion.
Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
After at least 30 minutes, if:
The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
If the display turns on, go to step 4.
If the display remains black, go to next step.
Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro. -
Hello! So I have a iPod 5th generation, and I just had a recent update, it was for iOS 6.1.3, and now for some reason, I can't get the iOS 7 update. Could anyone help me?
Apple's servers are slammed right now with iOS 7 downloads AND activation requests.
Be patient and try again later. -
I have a PowerBook G4 with a non-functioning monitor. It used to work with an external monitor, but I reinstalled the OS, which cleared the display preferences and now when I restart it won't detect the external monitor. This means I can't use the computer anymore. How do I fix? I tried using the Command+F2 keyboard shortcut, but it doesnt' work. It's possible that since I reinstalled the OS, it still needs to be set up, so there's only a welcome screen (but since I can't see it I'm not sure).
There is no limit to the number of times you can re-install Office on the same computer.
You can activate by telephone:
The last paragraph is the relevant bit -
The voice that was on when I first set up my ipad came back on and now I have to double click to get into my apps and can't use my apps because her voice is talking. How do I make the voice stop and my IPAD work again.
If you've turned VoiceOver on then see if triple-clicking the home button turns it off, and then change what Settings > General > Accessibility > Triple-Click Home is set to.
Otherwise, via 'the touch to select double-tap to activate' process you need to go into Settings > General > Accessibility > VoiceOver and turn it off
The manual (http://support.apple.com/manuals/#ipad) also says that you should be able to switch voice-over off by connecting to your computer's iTunes :
Turn VoiceOver on or off in iTunes: Select iPad in the iTunes sidebar. In the Options section of the Summary pane, click Configure Universal Access. Select VoiceOver, then click OK.
So select Configure Universal Access at the bottom of the Summary tab and set Seeing to Neither -
I used utilities to source my 10.6 snow leopard install disc to my main hardrive, and now when I turn on my computer the apple with the spinning wheel stays on the screen and stuck like that. How do I fix it Help please. I already tried all the commands such as Command R, Holding down the Option key, C and holding down shift at the start up but nothing happens.
initialy All I was trying to do was downgrade 10.7 to 10.6 .You have to consider the possibility the hard drive may be dying. If your data isn't backed up, try one of the tools below:
https://discussions.apple.com/docs/DOC-1689
Once you are sure your data is backed up, we can examine other possibilities. In the meantime call AppleCare for your original installation DVDs. You may need them. -
hi, please can you tell me when the ipad mini 2 is coming out? i don't know whether to get the ipad mini, or wait for the 2nd generation
Oh, ok. thanks for the help anyway
-
I upgraded my ipad and now my password changed. how do i get the temp password for entry ???
i upgraded my ipad software and now my password changed. how do i get the temp password for entry ???
The same thing happened to me??????
-
My MacBook Pro fell and now when I turn it on its stuck at the apple logo screen with a loading circle underneath it. What can I do to get passed this?
Sounds like something internal was damaged in the fall, probably the disk drive. Take to Apple and ask them to fix it.
Allan
Maybe you are looking for
-
I have a Mac Pro using Lion, with SSD for system drive. Drive stopped booting, but otherwise appeared healthy. Restored from system backup. Now drive seems to work properly, BUT my logon password no longer works. Password OK for account; can acce
-
How to change the vendor code in intercompany PO
actually PO was created with wrong vendor code. after this MIGO done, all the product sale out MIRO done invoice done. Now at this point *what we 'll have to do to change the vendor code*
-
HTC Trophy Alerts/Notifications
For those that have used the phone, a few questions about various HTC Trophy alerts/notifications--for things like missed calls, voicemails, SMS/MMS messages, emails, etc.: 1. For any of those items mentioned above, is there a way to have an alert/no
-
Tamplate based button in Report Column
Hi there, Is there any way to put tamplate based button into report column. I have a "sliding doors" css button in my theme's CSS file and I would like to use in in the report column. Thanks
-
Hi friends, I am running packing list smartform for output type PL00 and it is generating output in spool. I want to display the output in the screen instead of spool. Can somebody help please. Regards, Chinna