2.4ghz Macbook pro battery issues
3 days ago my battery began acting strange. I did not 'upgrade' to Snow Leopard, but at 100 cycles, I'm getting 'Check Battery' status, and a Full charge capacity that will range from 2800-3880,( at one point, for about an hour it read 4800 with a "Good" status). Is this just a defective battery?
Today:
Battery Information:
Charge remaining (mAh): 3367
Fully charged: No
Charging: Yes
Full charge capacity (mAh): 3880
Health Information:
Cycle count: 106
Condition: Check Battery
Battery Installed: Yes
Amperage (mA): 1180
Voltage (mV): 12540
12.21.09 8:55pm
Battery Information:
Charge remaining (mAh): 4766
Fully charged: Yes
Charging: No
Full charge capacity (mAh): 4899
Health Information:
Cycle count: 105
Condition: Good
Battery Installed: Yes
Amperage (mA): -81
Voltage (mV): 12273
and earlier on the 21st (I didn't save it) it read 2800 full charge, with "check battery"
Message was edited by: musiciscool
Similar Messages
-
Macbook Pro battery issues - from fully charged to 8% in under 60 mins?
Hi, I wonder if someone could point me in the right direction. Last night after fully charging my macbook pro battery in under 60 minutes it had less than 8% less. I bought this on the 1st Dec 2007 and haven't changed the battery.
I really don't know what any of the below means, but here goes:
Please help as I am no tecky.
Thank you
Catherine.
Battery Information:
Model Information:
Serial Number: Sony-ASMB012-372d-276e
Manufacturer: Sony
Device name: ASMB012
Pack Lot Code: 0003
PCB Lot Code: 0000
Firmware Version: 102a
Hardware Revision: 0500
Cell Revision: 0303
Charge Information:
Charge remaining (mAh): 2509
Fully charged: Yes
Charging: No
Full charge capacity (mAh): 2512
Health Information:
Cycle count: 154
Condition: Check Battery
Battery Installed: Yes
Amperage (mA): -447
Voltage (mV): 12389
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 10
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 5
Automatic Restart On Power Loss: No
Wake On AC Change: No
Wake On Clamshell Open: Yes
Wake On LAN: Yes
Display Sleep Uses Dim: Yes
Battery Power:
System Sleep Timer (Minutes): 5
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 1
Wake On AC Change: No
Wake On Clamshell Open: Yes
Display Sleep Uses Dim: Yes
Reduce Brightness: YesAs you are aware, batteries (no matter what manufacturer) are consumable devices and is only covered for one year (barring any type of abuse). With your purchase date being in 2007, this would not be covered under your AppleCare extended service plan.
Suggest you make an appointment for your local Apple Genius Bar and they can perform a Battery & Adapter test. You can always start the process by contacting AppleCare (1.800.APL.CARE) and log down your case number after you have completed your discussions with them, so when you get to the Genius Bar, it will save you time. At that point they will be able to determine if the battery is defective and commence the replacement process. Include your case number in the notes section of your Genius Bar appointment form. This tests will check your MagSafe adapter and battery at the same time and takes about a couple of minutes if that. Hope this helps guide you through the process.
Cheers,
Pete -
Hello,
I am one of the many consumers suffering from the bloating battery issue found in the 17inch MacBook Pro. I have found tons of info on this and people are reporting even the second or third battery having the same issue. That being said, is the issue really with the battery or with the computer? I know they put out a software update that was supposed to fix the problem, does that point to a problem with the computer?
A few apple representive said the battery breaking out of the casing was a safety feature, is there any way harmful chemicals are released when the seal on the component is damaged leaving the battery exposed?Well I would call back and tell them there are numerous instances where the battery replacement has been honored as part of the exchange/replacement program, especially since it is safety issue. Get a case number, next time you speak to someone. And if you don't get a satisfactory result, call back and escalate the call to customer relations. Until then turn off the computer and don't use it.
-
17 inch latest macbook pro battery issue
17 inch Macbook pro 4 days old. i7 2.4 Ghz 4 GB RAM 750 GB HDD. (Bluetooth and wifi is off) Using ethernet port and 1 USB port.
I just recently bought macbook pro. I love this machine coming from pc user line. I was having fan going loud issue called apple support she walk me through SMC reset procedure and its been better since. But i was told by support tech it should last more then 2 hours on battery life.
I do basic computing and some movies once in while. I also told support tech i like full brightness as i have problem seeing on dim display. He said doesnt matter it should still last 4 to 5 hours battery life. So I fully charged the battery after SMC reset and noticed this time it lasted approximate 3 hours. Anyone has same issue? Is this normal or not? Please help. Should I take back to apple store?
So far i have installed
VLC player
Vuze
setup one email account.
Thanks
CrabmanModel Information:
Serial Number: DP-**-60d5
Manufacturer: DP
Device name: bq20z951
Pack Lot Code: 0000
PCB Lot Code: 0000
Firmware Version: 0042
Hardware Revision: 0001
Cell Revision: 0119
Charge Information:
Charge remaining (mAh): 12873
Fully charged: Yes
Charging: No
Full charge capacity (mAh): 12873
Health Information:
Cycle count: 155
Condition: Good
Battery Installed: Yes
Amperage (mA): 374
Voltage (mV): 8372
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 10
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 10
Automatic Restart On Power Loss: No
Wake On AC Change: No
Wake On Clamshell Open: Yes
Wake On LAN: No
Display Sleep Uses Dim: No
GPUSwitch: 2
Battery Power:
System Sleep Timer (Minutes): 10
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 10
Wake On AC Change: No
Wake On Clamshell Open: Yes
Display Sleep Uses Dim: Yes
GPUSwitch: 2
Reduce Brightness: Yes
Hardware Configuration:
UPS Installed: No
AC Charger Information:
Connected: Yes
Charging: No -
I have a Macboon PRO1 5 inch and sometimes the battery shows a cross sign and the fan doesn't stop running. I sent in thrice to Apple for repair. Everytime it comes back with a new problem. Now my battery doesn't charge at all and discahrges very rapidly.Appple has changed everything they can think of, the power adapter,logic board, battery ,the battery connector, but that just seem to fix the problem. Did anyone else have a similar issue? Cause everytime I call Apple they just ask me to send it back in.
Well I did ask for a senior level advisor and even he said he can't do anything and that I need to send in for repair again. The whole experience with Apple has been so frustrating. I was hoping that if someone had similar issues like I did with the battery ,maybe I can simply ask again for a new power adapter or something(based on what others experience) without having to send it in again.
-
MacBook and MacBook Pro Battery Update
http://www.apple.com/support/macbook_macbookpro/batteryupdate/
Apple has recently discovered that some batteries used in its MacBook and MacBook Pro notebooks may have battery performance issues. Apple is offering a software update that is designed to improve battery performance.
The battery update is available immediately via Software Update or downloadable here.
Note: The factors causing the performance issues do not present a safety risk. You may continue to use your current battery.
This battery update should be run on all MacBook and MacBook Pro computers and extra batteries that were purchased between February 2006 and April 2007.
If, after you have installed the battery update, your battery has any of the symptoms listed below, please make a reservation to bring your computer with its battery to your local Apple Retail Store, or contact an Apple Authorized Service Provider (AASP), or call your local Apple Support Contact Center. If Apple or an AASP determines that your battery is eligible for replacement, you will receive a new battery, free of charge, even if your MacBook or MacBook Pro is out of warranty.
For MacBook and MacBook Pro systems with Intel Core Duo processors, this program extends repair coverage on the battery for up to two years from the date of purchase of the computer.
Identifying an affected battery
Affected batteries will have one or more of the following symptoms:
Battery is not recognized causing an “X” to appear in the battery icon in the Finder menu bar.
Battery will not charge when computer is plugged into AC power.
Battery exhibits low charge capacity/runtime when using a fully charged battery with a battery cycle count (as shown in System Profiler) of less than 300.
Battery pack is visibly deformed.
Note: If your MacBook or MacBook Pro battery does not have any of the symptoms noted above, your battery does not need to be replaced.
Next Steps
To participate in this worldwide program, your MacBook or MacBook Pro battery must show the symptoms noted above. If it does, please make a reservation to bring your computer and battery to your local Apple Retail Store, or contact an Apple Authorized Service Provider (AASP), or call your local Apple Support Contact Center. The U.S. support number is 1-800-275-2273. If you are located outside the U.S., please see Apple's international contact list for your local Apple Technical Support phone number. An Apple technical support representative or an Apple Authorized Service Provider (AASP) will determine if the battery is eligible for replacement, free of charge. Customers are responsible for transportation costs to eligible AASPs and retail stores.
If a replacement battery is sent to you via airmail, it is important that you return the older battery to Apple so that it can be properly recycled.
This program extends repair coverage on the battery for up to two years from the date of purchase of the computer for Intel Core Duo-based MacBook and MacBook Pro computers. Apple will continue to evaluate the battery update program and will provide further extensions as needed. Apple also reserves the right to modify the program if other solutions that address the battery performance issues become available.For MacBook and MacBook Pro systems with Intel Core Duo processors, this program extends repair coverage on the battery for up to two years from the date of purchase of the computer.
Pretty nice change for those C2D's -
Dota 2 and Macbook pro battery
My early 2011 15 inch macbook pro battery drains while connected with 85w charger when i am playing dota 2. Dota 2 runs faily well with very little lag in almost high setting. Shouldn't 85w charger provide adequte power for gaming. Dota 2 is not even a very demanding game. I have only played few small 2d games in my pro and this may be the first time i am playing a 3d game. And also sometimes it doesnt drain even when i play 2-3 matches but most of the other times it drains in single match. I have yet to see it drain down 90% but still. What options do i have to fix this? I am graphic designer so i sometimes do video editing in my macbook pro and i m quite sure some of those renderings are more system hungry than dota 2 and no drain while doing that. Thanks in advance.
What do you mean it didn't work? Are you having a battery issue that the update did not fix? Need some more info. If you look at the webpage that I linked to, it advises to have affected batteries replaced.
Identifying an affected battery
Affected batteries will have one or more of the following symptoms:
Battery is not recognized causing an “X” to appear in the battery icon in the Finder menu bar.
Battery will not charge when computer is plugged into AC power.
Battery exhibits low charge capacity/runtime when using a fully charged battery with a battery cycle count (as shown in System Profiler) of less than 300.
Battery pack is visibly deformed.
Note: If your MacBook or MacBook Pro battery does not have any of the symptoms noted above, your battery does not need to be replaced.
If you're replacing batteries every 3 months I would take a look at how you are maintaining your battery. Are you calibrating it when it arrives and then every 6 to 8 weeks afterword? Are you running graphically intensive programs? Do you have a lot of background process in your activity monitor that are taxing the system? Most folks I have seen post here find their battery issues resolved after a replacement, not recurring every 3 months. -
I bought in december of 2008 a 2.4ghz macbook pro and I think the gpu is starting to fail. Can I still be covered for a change because of the faulty nvidia gpu?
If your computer qualifies - MacBook Pro: Distorted video or no video issues
If it does, call Apple Customer Relations or print out a copy of the article and bring it in to the repair shop. -
2008 early macbook pro battery normal and charging but stays at 0% Won't charge.
I have reset the SMC and PRAM
The charge light is orange on the magsafe charge cord.
Do I need new battery or is it a hardware issue?
Model Information:
Serial Number: ˇ
Manufacturer: SMP
Device Name: ASMB012
Pack Lot Code: 4
PCB Lot Code: 0
Firmware Version: 0dc0
Hardware Revision: 0
Cell Revision: 0
Charge Information:
Charge Remaining (mAh): 0
Fully Charged: No
Charging: Yes
Full Charge Capacity (mAh): 4008
Health Information:
Cycle Count: 125
Condition: Normal
Battery Installed: Yes
Amperage (mA): 0
Voltage (mV): 8459
Message was edited by: mcj2112Reset the SMC > http://support.apple.com/kb/HT3964
It's clear that the battery has got enough capacity to work correctly, so something happens with the MagSafe port or its charger. If you have another charger, try it, and if not, take the MacBook and the charger to an Apple Store or reseller. It's better to do this as we don't know if the problem is in the charger or in the MacBook Pro -
I incorrectly posted this in the wrong thread this morning.
I'm hopeful you might be able to help me diagnose a problem I'm having. I'll provide as much detail as possible.
I have a first generation MacBook Pro. As of this morning I was running 10.5.6 and up until this week was using a linksys router and a comcast cable modem.
I used to have a great wifi signal throughout the house (always full strength), and around 12-18 months ago noticed the signal would weaken. The best I would get would be minus the top bar on the signal, and usually only if I was directly above or next to the room with the router. There were no new phones or devices added that might adjust the signal. On the other side of the house, I would have no signal at all.
My wife has a nine year old ibook and has no issues connecting through wifi.
When I bring my laptop to her parents' house or to the Apple store, where they use Belkin on N or Airport Extreme, I get a full signal.
I've recently suffered a hard drive failure and had a replacement drive installed. The problem persists despite the software update.
Not knowing if it was a router issue or an airport card issue or a combination thereof, I went to the Genius Bar. The genius recommended I upgrade my router to Airport Extreme, and if that doesn't work to return it and he'd focus on the airport card or antenna. I could get the flat rate repair (no AppleCare at this point) for $320+ to repair the problem if Extreme didn't work.
I installed the Airport Extreme router and got a full signal in the basement, far side of the house, upstairs - everywhere. Until around 10pm. The signal died from the basement. If I walked into the room with the Airport Extreme router, I'd get a full signal. If I left the room, I'd get a partial signal. If I walked any distance (10-12 feet), the signal would die. I restarted both the modem and router with no change. I reinstalled the linksys router and got a depreciated connection. I restarted the Airport Extreme again and got a full signal throughout the night, morning, through restarts, and when I returned home from work.
Last evening after using youtube extensively it died again. Linksys would barely work if I switched back, and no matter how many times I restarted I couldn't get the signal to last outside of the area of the router. I left it in the basement overnight shut down, restarted this morning, and had a full signal.
I'm looking for any potential guesses as to what may be causing the problem. I don't want to replace the card if it's the antenna or sink too much cash into a machine if it's a heat related issue linked to Generation 1 syndrome.
During all of this the ten year old ibook works fine. I know a lot of macbook pros have issues with their wireless and don't want to sink in the cash if it's more complex than that. Any advice is much appreciated!Hi nashie1002,
If you are having issues connecting to your WPA2 WiFi network after a recent update, you may find the troubleshooting steps and settings in the following articles helpful:
Wi-Fi: How to troubleshoot Wi-Fi connectivity
http://support.apple.com/kb/HT4628
Apple Support: About Wireless Diagnostics
http://support.apple.com/kb/HT5606
iOS and OS X: Recommended settings for Wi-Fi routers and access points
http://support.apple.com/kb/ht4199
It may also be worth doing a search for the specific model number of your router to see if anyone has noted any issues with Mavericks.
Regards,
- Brenden -
MacBook Pro battery had accumulated more than a 1000 charges, and stopped functioning unexpectedly. Went and got the battery replaced. Just saw that SMC Firmware 1.6 update deals with this. Possible to get my money back?
The firmware update corrects an error that may occur, however the techs would have checked the condition of the battery prior to installing a new one. If the battery was questionable, the firmware update was really not too important.
You can check the battery condition by going to the apple, left side of the menu bar, About This Mac, More Info, System Report, Hardware, Power and see what it says about Cycle Count, Condition, Capacity: Condition anything but Normal needs to be checked and may need to be replaced.
The cycle count of 1,000 charge cycles is the typical life of a Lithium-Ion battery, the point at which the capacity drops to 80% of the as built capacity. -
Can't install windondows 8.1 on my macbook pro - format issue
Can't install windondows 8.1 on my macbook pro - format issue
Running latest version of Mavericks.
Followed the exact bootcamp proceduce.
Have official window 8.1 version on cd.
All goes well until I have to format the 65Gb partition. Disk=0 and partition=4
Can't get over it. Altough I formatted it via a hint found on the internet with "dislpart" in NTFS. Wich also went weel and give the labelname "BOOTCAMP". But still no luck.
I have two questions:
1/ How to start my mac again in normal mavericks mode?
2/ How can I overcome the windows installation issue?
Tried already a lot of hints found on the internet.First, make a time machine backup. You will need to erase ands reformat your hard drive. I had the same issue. The issue is that you can't install Windows using bootcamp without having the hard drive formatted as Mac OS Extended (Journaled). Do this from disk utility or recovery mode (hold down command and r at startup). Then you have to restore the backup to the hard drive. Then make a usb installer drive with bootcamp and then partition and install. Here's a tip: after you install bootcamp and are in the Windows desktop, go into the installer drive and then go into the bootcamp or support folder, then find a installer that contains the Apple bootcamp drivers. Also, you will need to convert the disk to an iso file. TO MAKE THE USB DRIVE FROM A DISC, USE THIS LINK
Boot Camp: Creating an ISO image from a Windows installation DVD - Apple Support -
2.4ghz MacBook Pro/30" Cinema Display Compatibility
I have a 15" 2.4ghz MacBook Pro (Intel Core 2 Duo) ...can hook it up to a 30" Cinema Display at the full resolution? If so, what adapter do I need?
Thanks!can hook it up to a 30" Cinema Display at the full resolution?
Yes.
what adapter do I need?
A dual-link DVI cable or a Mini DisplayPort to dual-link DVI adapter depending on the computer's ports.
(55596) -
HT204347 Do you connect the charger in the MacBook Pro battery damage if using device ?
Do you connect the charger in the MacBook Pro battery damage if using device ?
i am sorry i not good speak englishProvided you are using the correct charger for your Mac (13" have a 65 watt charger, 15" and 17", an 85 watt charger), it has enough capacity to power the computer for normal tasks, and the leftover power can charge the battery at the same time. If you are doing something very intensive, there may not be leftover power, but the Mac will take power from the battery if needed. Once the battery is fully charged, the pilot light in the charger plug will change from orange to green and no further charge will be applied to the battery.
You can use your Mac plugged to the charger with no damage to the battery or the computer. -
Macbook pro shutdown issue when I push the power button it immediately goes into sleep mode
Hello Marrio22,
Thank you for the question. With OS X Mavericks, the power button has new functionality:
OS X Mavericks updates the power button behavior on Mac computers.
Using the Power Button to Sleep & Wake
Tap the power button in Mavericks to put your Mac to sleep or to wake it up:
Tap the power button once to put your Mac to sleep.
Tap the power button again to wake your Mac.
Press the power button for less than a half a second to sleep or wake your Mac. This duration is similar to pressing the Space bar or Return key to wake your Mac. The power button works this way across all Macs using OS X Mavericks, including both notebook and desktop computers.
Accessing the Shut Down Dialog
Press and hold the power button for 1.5 seconds, to bring up additional options:
Forcing the Mac to Turn Off
Hold down the power button for 5 seconds to force the computer to turn off. Important: You may lose unsaved documents if you force the computer to turn off this way. Use this method of turning off your Mac only if it has become unresponsive for an extended period of time. Normally you should shut down the computer by selecting Shut Down from the Apple menu, or from the shut down dialog pictured above.
OS X Mavericks: Using the power button
http://support.apple.com/kb/HT5869
Thank you for using Apple Support Communities.
Best,
Sheila M.
Maybe you are looking for
-
DBMS_Session.List_Context() for GLOBALLY ACCESSED Context
I created CREATE CONTEXT myContext USING PACKAGE myPackage ACCESSED GLOBALLY ; CREATE OR REPLACE PACKAGE myPackage PROCEDURE Set_My_Context( piId IN INTEGER, piValue IN INTEGER) ; END myPackage ; CREATE OR REPLACE PACKAGE BODY myPackage PROCEDURE Set
-
By default wage type is defaulting in Payslip
Dear Mates, I've created one custom PCR for one day salary deduction & working fine but getting problem like even I haven't maintained relevant data for one day salary deduction still the wage type is being appeared in Payslip. I'm unable to understa
-
Safari is constantly not responding
Safari is constantly not responding, especially when loading java, uploading videos etc. Can I do anything about it? Can I somehow restore the safari (I have tried to rest it, but nothing was improved). thanks
-
same strut darker skin www.bleed3d.com/walk%202.htm
-
I am trying to use Migration Assistant but it tells me that there is an error when using it - but it doesn't tell me what and I only have teh option to quit!