2012 R2 Cluster - Issues creating cluster

New Dell VRTX server with 2 server blades. Installed Server 2012 R2 on both blades and all working ok.
Ran the 'Validate Configuration' wizard and all ok apart from Storage Spaces, which we won't need as we have hardware RAID.
Then ran create cluster wizard and works ok until it goes to create and then fails:-
Adding special permissions to the computer object failed.
Trying to add 'Full-Access' permissions for security principal
S-1-5-21-1054053922-559824688-2072063007-68696 to computer object
CN=UKWOR-CLUSTER01,OU=Cluster,OU=SERVER,OU=HAR,OU=UK,OU=AVL,DC=xxxx,DC=xxxx,DC=lan
failed. Verify that the user running create cluster has permissions to update
the computer object in Active Directory Domain Services. The parameter is
incorrect.
"CreateClusterNameCOIfNotExists (6888): Configuring Computer Object UKWOR-CLUSTER01 to act as the CNO on DC \\ xxx.lan"
"CreateClusterNameCOIfNotExists (6916): Configuring Cluster CNO resource."
"CreateClusterNameCOIfNotExists (6942): Cannot provide user special permissions to the object.
Error <87> (Step ErrorPutSD)."
"PhaseManager::EndPhase (235): Phase 109
"CreateNetworkName (4618): Failed to create Computer Object for NetName Cluster Name on DC \\ xxx.lan. Error 87."
I've tried this also by pre-creating the computer object (in the right OU and following guides online for setting the permissions, disabling it etc. I do not have Domain Admin rights as we are a large multi-national company. But I can create computer accounts
in my OU and I have given the administrator account that's logged into the servers the same rights on the relevant OU.
Any suggestions or ideas as to what I can do to progress with this as I've run out of ideas :(

Thanks for the info PMThomas,
@Lerun: For us it was permissions as well in the end. A quick fix I found to get arround it until you find the offending AD permissions is to create the new Cluster Computer Object in AD. Disable the account. Then go into security for the
Computer Object and disable inheritance, make sure you choose remove when promted. For us this must have removed the offending AD permissions as we could then create the cluster.
I've not managed to work out which permission it was yet. I guess I could test by removing each of the inheritted permissions one by one until the cluster wizard is successfull.
Heres a link to my post on our troubleshooting process if you fancy a LONG read!!
http://social.technet.microsoft.com/Forums/en-US/8d1c504b-c3fd-4eaf-8309-ef4e9fdbd82f/unable-to-create-a-new-cluster-on-our-domain?forum=winserverClustering

Similar Messages

Issues creating cluster on WLS 6.0

          I am new to weblogic domain , so plz bear if some questions are too obvious.
          Just a breif description of what i am trying to do:
          To start wiith I want to just cluster two servers that host a Stateless Session EJB
          and configure round-robin load-balancing .
          I also want to test that when one of the servers is unavailable the client request
          is still served by the other server in the cluster.
          I have 2 weblogic 6.0 running on m/cs xyz032 and xyz019 , both on port 7001
          I am jotting down the issues/insight that i have/need :
          1. I use the server on my m/c xyz032 (port 7001) as the admin server (mydomain>Servers>myserver).
          First question (Can a admin participate in the cluster ??)
          2. To make the server on m/c xyz019 as a part of the cluster , As far as i understand
          i have to create a server first from the admin server so that it shows up
          in the list of available servers. So that when you create a Cluster you can choose
          from the list of available servers. (FYI I am using the GUI Admin to configure this)
          But when i try to create a server , it only takes a name and port number. How do
          i create a new server that points to the server running on xyz019 (ip say xxx.x.xx.xxx).
          I also tried creating a new machine but that too does not take an ip address for
          the remote m/c.
          3. When i create a cluster from the admin GUI , it asks for a name(fine) and cluster
          address .
          I read the documentation that states it can be an ip address (not sure which ) .
          Do i need to give the comma separated ip addresses of both the servers taking part
          in the cluster ???
          4. Is it mandatory that servers to be clustered be running on the same port ?
          5. The document says that the object (EJB)to be clustered should be deployed to both
          the servers ( I agree, no doubt about it)
          But the deployment option on the GUI also lets me deploy to the cluster . Does that
          mean if i choose the deployment target to be cluster then the admin will deploy the
          bean to all the servers taking part in the cluster.
          I feel your experience with this will help me in a head start .
          Thanks
          Ashok Shamnani


          Thanks Kumar.
          Also like to add here ,
          when i start a managed server passing the arguments as the ip of the admin server
          , the managed server(the remote server) shows up in the admin server. Once it shows
          up then i can assign it to a cluster or do whatever deployments i want to.
          Kumar Allamraju <[email protected]> wrote:
          >
          >
          >Ashok Shamnani wrote:
          >
          >> I am new to weblogic domain , so plz bear if some questions are too obvious.
          >>
          >> Just a breif description of what i am trying to do:
          >>
          >> To start wiith I want to just cluster two servers that host a Stateless
          >Session EJB
          >> and configure round-robin load-balancing .
          >> I also want to test that when one of the servers is unavailable the client
          >request
          >> is still served by the other server in the cluster.
          >> I have 2 weblogic 6.0 running on m/cs xyz032 and xyz019 , both on port
          >7001
          >>
          >> I am jotting down the issues/insight that i have/need :
          >>
          >> 1. I use the server on my m/c xyz032 (port 7001) as the admin server (mydomain>Servers>myserver).
          >> First question (Can a admin participate in the cluster ??)
          >>
          >
          >Yes.
          >Just assign myserver to to mycluster from console (assuming mycluster is
          >your cluster name)
          >But i would recommend this. I would always use admin server for administrative
          >tasks.
          >
          >
          >>
          >> 2. To make the server on m/c xyz019 as a part of the cluster , As far
          >as i understand
          >> i have to create a server first from the admin server so that it shows
          >up
          >> in the list of available servers. So that when you create a Cluster you
          >can choose
          >> from the list of available servers. (FYI I am using the GUI Admin to configure
          >this)
          >> But when i try to create a server , it only takes a name and port number.
          >How do
          >> i create a new server that points to the server running on xyz019 (ip
          >say xxx.x.xx.xxx).
          >>
          >
          >You can specify the IP address under server-instance --> configuration-->General
          >tab, look for
          >Listen Address
          >
          >>
          >> I also tried creating a new machine but that too does not take an ip
          >address for
          >> the remote m/c.
          >>
          >> 3. When i create a cluster from the admin GUI , it asks for a name(fine)
          >and cluster
          >> address .
          >> I read the documentation that states it can be an ip address (not sure
          >which ) .
          >> Do i need to give the comma separated ip addresses of both the servers
          >taking part
          >> in the cluster ???
          >>
          >
          >You can simply ignore it, or use the cluster address given by your Admin.
          >e..g when i do ping cyclut, it resolves to a different IP every time.
          >
          >>
          >> 4. Is it mandatory that servers to be clustered be running on the same
          >port ?
          >>
          >
          >Yes.
          >
          >>
          >> 5. The document says that the object (EJB)to be clustered should be deployed
          >to both
          >> the servers ( I agree, no doubt about it)
          >> But the deployment option on the GUI also lets me deploy to the cluster
          >. Does that
          >> mean if i choose the deployment target to be cluster then the admin will
          >deploy the
          >> bean to all the servers taking part in the cluster.
          >>
          >
          >Yes.
          >Either you can deploy the bean in a cluster or per-server instance.
          >
          >--
          >Kumar
          >
          >
          >>
          >> I feel your experience with this will help me in a head start .
          >>
          >> Thanks
          >>
          >> Ashok Shamnani
          >

Create Cluster Wizard in SCVMM 2012 doesn't have IP Address page

i installed the SCVMM 2012 version 3.0.6019.0.
When i use the Create Hyper-V Cluster under Fabric page to create a Cluster.
the Create Cluster Wizard doesn't have the IP Address page to let me input the IP for the Cluster.
after i answer all the wizard, the Install Cluster job shown Error 25325
The cluster creation failed because of error At least one IP address needs to be configured..
so, how to solve it?
thanks alot.

Old thread..
But I got the same problem creating a cluster on SCVMM 2012 R2. To get around it I instead created the cluster using powershell and it worked great:
$HostName1 = "HOST01"
$HostName2 = "HOST02"
$Clustername = "CLUSTER01"
$ClusterIP = "192.168.1.50"
$VMMRunAsAccount = "VMM_AdminAccount"
$credential = Get-SCRunAsAccount -Name $VMMRunAsAccount
$hostsList = @()
$hostsList += Get-SCVMHost -Computername $HostName1
$hostsList += Get-SCVMHost -Computername $HostName2
Install-SCVMHostCluster -ClusterName $Clustername -VMHost $hostsList -RunAsynchronously -Credential $credential -ClusterIPAddress $ClusterIP
_____________________________________ /Michael R

Unable to create cluster, hangs on forming cluster

Hi all,
I am trying to create a 2 node cluster on two x64 Windows Server 2008 Enterprise edition servers. I am running the setup from the failover cluster MMC and it seems to run ok right up to the point where the snap-in says creating cluster. Then it seems to hang on "forming cluster" and a message pops up saying "The operation is taking longer than expected". A counter comes up and when it hits 2 minutes the wizard cancels and another message comes up "Unable to sucessfully cleanup".
The validation runs successfully before I start trying to create the cluster. The hardware involved is a HP EVA 6000, two Dell 2950's
I have included the report generated by the create cluster wizard below and the error from the event log on one of the machines (the error is the same on both machines).
Is there anything I can do to give me a better indication of what is happening, so I can resolve this issue or does anyone have any suggestions for me?
Thanks in advance.
Anthony
Create Cluster Log
==================
Beginning to configure the cluster <cluster>.
Initializing Cluster <cluster>.
Validating cluster state on node <Node1>
Searching the domain for computer object 'cluster'.
Creating a new computer object for 'cluster' in the domain.
Configuring computer object 'cluster' as cluster name object.
Validating installation of the Network FT Driver on node <Node1>
Validating installation of the Cluster Disk Driver on node <Node1>
Configuring Cluster Service on node <Node1>
Validating installation of the Network FT Driver on node <Node2>
Validating installation of the Cluster Disk Driver on node <Node2>
Configuring Cluster Service on node <Node2>
Waiting for notification that Cluster service on node <Node2>
Forming cluster '<cluster>'.
Unable to successfully cleanup.
To troubleshoot cluster creation problems, run the Validate a Configuration wizard on the servers you want to cluster.
Event Log
=========
Log Name:      System
Source:        Microsoft-Windows-FailoverClustering
Date:          29/08/2008 19:43:14
Event ID:      1570
Task Category: None
Level:         Critical
Keywords:
User:          SYSTEM
Computer:      <NODE 2>
Description:
Node 'NODE2' failed to establish a communication session while joining the cluster. This was due to an authentication failure. Please verify that the nodes are running compatible versions of the cluster service software.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
    <Provider Name="Microsoft-Windows-FailoverClustering" Guid="{baf908ea-3421-4ca9-9b84-6689b8c6f85f}" />
    <EventID>1570</EventID>
    <Version>0</Version>
    <Level>1</Level>
    <Task>0</Task>
    <Opcode>0</Opcode>
    <Keywords>0x8000000000000000</Keywords>
    <TimeCreated SystemTime="2008-08-29T18:43:14.294Z" />
    <EventRecordID>4481</EventRecordID>
    <Correlation />
    <Execution ProcessID="2412" ThreadID="3416" />
    <Channel>System</Channel>
    <Computer>NODE2</Computer>
    <Security UserID="S-1-5-18" />
</System>
<EventData>
    <Data Name="NodeName">node2</Data>
</EventData>
</Event>
====
I have also since tried creating the cluster with the firewall and no success.
I have tried creating the node from the other cluster and this did not work either
I tried creating a cluster with just a single node and this did create a cluster. I could not join the other node and the network name resource did not come online either. The below is from the event logs.
Log Name:      System
Source:        Microsoft-Windows-FailoverClustering
Date:          01/09/2008 12:42:44
Event ID:      1207
Task Category: Network Name Resource
Level:         Error
Keywords:
User:          SYSTEM
Computer:      Node1.Domain
Description:
Cluster network name resource 'Cluster Name' cannot be brought online. The computer object associated with the resource could not be updated in domain 'Domain' for the following reason:
Unable to obtain the Primary Cluster Name Identity token.
The text for the associated error code is: An attempt has been made to operate on an impersonation token by a thread that is not currently impersonating a client.
The cluster identity 'CLUSTER$' may lack permissions required to update the object. Please work with your domain administrator to ensure that the cluster identity can update computer objects in the domain.

I am having the exact same issue... but these are on freshly created virtual machines... no group policy or anything...
I am 100% unable to create a Virtual Windows server 2012 failover cluster using two virtual fiber channel adapters to connect to the shared storage.
I've tried using GUI and powershell, I've tried adding all available storage, or not adding it, I've tried renaming the server and changing all the IP addresses....
To reproduce:
1. Create two identical Server 2012 virtual machines
(My Config: 4 CPU's, 4gb-8gb dynamic memory, 40gb HDD, two network cards (one for private, one for mgmt), two fiber cards to connect one to each vsan.)
2. Update both VM's to current windows updates
3. Add Failover Clustering role, Reboot, and try to create cluster.
Cluster passed all validation tests perfectly, but then it gets to "forming cluster" and times out =/
Any assistance would be greatly appreciate.

IP conflict detacted by the OS after a cluster is created.

I am creating a Cluster in Windows with 3 nodes using Windows 2008R2 64bits in preparation of creating a AlwaysOn Group for SQL 2012 Server after that.
I got a little problem with the IPs (conflicting) after I have created a cluster and wonder if someone could suggest what is the best practice to do that.
I've followed 'Create a New Faiover Cluster'
http://technet.microsoft.com/en-us/library/cc755129.aspx
using the Faiover Cluster Manager to create a cluster. I loved this tool. But unfortunately, after the 3 nodes successfully added and a new cluster is created, I got a Window's message saying that there is an IP conflict with the other computer.
After working our network adminstration, it turns out that in the network setting on each node,
the IP number generated after the Cluster is not the one that is assigned within the range by the DNCP server. The IP in Ethernet adapter Local Area Connection section is ok, unchanged.
It is the one under the 'Ethernet adaptor Local Area Connection* 10' of Microsoft Failover Cluster Virtual Adapter showing a dummy '169....'.
From what our network administrator told me, it is possible that we ran out of/use up the range assigned. So, I am now given three brand new IP numbers to use for this clustering.
But I am not sure how to use it to incorporate when I run the wizard in Failover Cluster Manager again, because it does not ask. So, my question is, what is the best approach to tell the cluster manager to use these new IP numbers. I have document
link http://technet.microsoft.com/en-us/library/ms190460.aspx to show me to change the IP number after the cluster is created. I wonder if this is the best practice or right way to
do that.
Thank you.
Note: All 3 three has its IP 'reserverd', so they don't get changed or expired on each computer before the clustering set up. When all goes well, I will get new hardware with static IPs and if my assumption is correct, I hope it will eliminate the
issue I am experiencing.
Martin
Martin Ng

Hi,
Please rerun the validation test then post the error or warning part, that report will quickly locate the issue. Please try to disable all your AV soft and firewall then try
again.
If you want to add some node to the current failover cluster, please refer the following KB first.
Add a Server to a Failover Cluster
http://technet.microsoft.com/en-us/library/cc730998.aspx
Hope this helps.
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

2012 R2 Standard File Server Cluster Confusion

Hi All:
I have 2 VMware 5.5 VMs running 2012 R2 Standard that have the Failover Cluster Manager role installed. I was having trouble validating the cluster before creating it & received this error:
Failed to find or allocate arbitration sectors for physical disk {fbf0422f-6844-4a3d-9ad9-542e8eebfec1} from node <SERVER>. These sectors are used to test reads
and writes to the disk. On a GPT disk, these sectors are located within the Cluster Metadata Partition, and this partition may need to be created from the Microsoft Reserved Partition so that the storage will validate. Please ensure that all GPT disks have
a Microsoft Reserved Partition (MSR) present. Error: 0x80070022.
I've been working w/Dell's VMware & SAN Support Teams & they sent me a link
https://social.technet.microsoft.com/Forums/windowsserver/en-US/d1524238-a891-4c7d-84ae-e885a9f59861/server-2012-clustering that says "you need to create an MSR partition on the drives", which I did on both my RDMs (1 for quorum; 1 for shared
storage). I ran the command after I selected the disk and now the disks look completely blank in Disk Management (I'd have to send a screenshot).
After that, cluster validation has no issues & I create the cluster. Now I cannot add either of the disks b/c:
Error Code: 0x8007174c
The disk is not configured in a way to be used with CSV. CSV disks must have a t least one partition that is formatted with NTFS or REFS.
So what did I do incorrectly? I had to use MSR to format the RDMs to validate the cluster, but now it wants another format. If anyone can find an actual MS document that goes into detail on where I went wrong, please include it,
as I've found nothing.
Thanks.

Just as the error say - you need to format the disks.
There are two steps to preparing a raw disk for use in a cluster. The first is to initialize it. That is what you did to get the cluster to actually see there were disks there to be used. The second is to put a file system on it by formatting
it. I recommend you use NFTS. Perform the format on just one of the nodes of the cluster.
Once you have an NTFS file system on the disk, you should be good to go.
. : | : . : | : . tim

Cluster Installation - SQL 2005 / 2003 - Creating cluster group

Hi All,
I am working on the cluster Installation in our environment and facing some issues at the time of installing first node MSCS Installation. let me summarize the activities done so far
Environment Details
Physical Disk :
G: (Physical Disk - SAN )
I : (Physical Disk - SAN )
C: Local disk
Q: (Physical Disk Quorum - SAN )
F: (Database and logs)
-- > SCS installed locally in the server in G drive
Virtual Hostname and IP : SeparateIP & cluster1
Node 1: Hostname and separate IP
Node 2 : hostname and Separate IP
Installed MSCS service and tested the same - its working fine
Installed SQL 2005 database in cluster mode and its working fine
Started installing SAP
Step 1: Installation of SCS instance in node A (Used F drive) - Successfull Installed
Step 2: Installation of First node MSCS in node A
Here I am facing an issue, in the end phase of the installation it will ask for creating cluster group -- > There I need to define the Global disk as F (Which is defined at the time of installing SCS instance) - But i dont see that disk is available in the drop down box .
Is there any other workaround to bring the Global disk while creating the cluster group (First node MSCS installation)
Looking forward for your suggestions
Thanks and Regards
Vijay

Regret for the late update
112266 solved my problem and In my case, I have bisected the disk as two but in the cluster environment that should not be the case. Ensure the the same in disk management
Regards
Vijay

Having issue with start weblogic cluster with tangosol cluster

Hi,
Oracle Coherence Version 3.3.1/389p1
Grid Edition: Development mode
We are using Weblogic 8.1.5 with Tangosol 3.3.1 on Linux servers.
And we added the initializing logic in the servlet's init() method to get all NamedCaches and put into the ServletContext.
When we start weblogic cluster, the first weblogic member will startup successfully with following messages :
<Nov 7, 2007 10:12:30 AM EST> <Info> <HTTP> <BEA-101047> <[2007-11-07 10ServletContext(id=259640596,name=clusterqa,context-path=)] initObjects: init>:12:31.565 Oracle Coherence 3.3.1/389p1 <Info> (thread=Main Thread, member=n/a): Loaded operational configuration from resource "zip:/home/server/clusterqa/wls81/DOCVIEW/docqa1/.wlnotdelete/extract/docqa1_DOC_clusterqa/jarfiles/WEB-INF/lib/coherence.jar!/tangosol-coherence.xml"
2007-11-07 10:12:31.598 Oracle Coherence 3.3.1/389p1 <Info> (thread=Main Thread, member=n/a): Loaded operational overrides from file "/home/www/WEB-INF/lib/tangosol-coherence-override.xml"
Oracle Coherence Version 3.3.1/389p1
Grid Edition: Development mode
Copyright (c) 2000-2007 Oracle. All rights reserved.
2007-11-07 10:12:31.938 Oracle Coherence GE 3.3.1/389p1 <Info> (thread=Main Thread, member=n/a): Loaded cache configuration from file "/home/www/WEB-INF/lib/pub-search-cache-config.xml"
2007-11-07 10:12:31.983 Oracle Coherence GE 3.3.1/389p1 <Info> (thread=Main Thread, member=n/a): sun.misc.AtomicLong is not supported on this JVM; using a synchronized counter. Though safe to ignore, you may upgrade to BEA's 1.5 JVM to fix this issue.
2007-11-07 10:12:33.267 Oracle Coherence GE 3.3.1/389p1 <Warning> (thread=Main Thread, member=n/a): UnicastUdpSocket failed to set receive buffer size to 1428 packets (2096304 bytes); actual size is 89 packets (131071 bytes). Consult your OS documentation regarding increasing the maximum socket buffer size. Proceeding with the actual value may cause sub-optimal performance.
2007-11-07 10:12:34.118 Oracle Coherence GE 3.3.1/389p1 <D5> (thread=Cluster, member=n/a): Service Cluster joined the cluster with senior service member n/a
2007-11-07 10:12:37.508 Oracle Coherence GE 3.3.1/389p1 <Info> (thread=Cluster, member=n/a): Created a new cluster with Member(Id=1, Timestamp=2007-11-07 10:12:33.323, Address=10.5.176.86:8088, MachineId=48982, Edition=Grid Edition, Mode=Development, CpuCount=4, SocketCount=2) UID=0x0A05B056000001161AAB782BBF561F98
2007-11-07 10:12:37.736 Oracle Coherence GE 3.3.1/389p1 <D5> (thread=Invocation:Management, member=1): Service Management joined the cluster with senior service member 1
2007-11-07 10:12:38.168 Oracle Coherence GE 3.3.1/389p1 <D5> (thread=DistributedCache, member=1): Service DistributedCache joined the cluster with senior service member 1
<Nov 7, 2007 10:12:38 AM EST> <Info> <HTTP> <BEA-101047> <[ServletContext(id=259640596,name=clusterqa,context-path=)] xslProcessor: init>
But trying to start the second weblogic member server, the startup process is stucked after tangosol cache initialization and the second weblogic member server never up running. Please see following messages :
<Nov 7, 2007 9:49:38 AM EST> <Info> <HTTP> <BEA-101047> <[ServletContext(id=153019550,name=clusterqa,context-path=)] initDSNames: init>
<Nov 7, 2007 9:49:42 AM EST> <Info> <HTTP> <BEA-101047> <[ServletContext(id=153019550,name=clusterqa,context-path=)] initObjects: init>
2007-11-07 09:49:43.156 Oracle Coherence 3.3.1/389p1 <Info> (thread=Main Thread, member=n/a): Loaded operational configuration from resource "zip:/home/server/clusterqa/wls81/DOCVIEW/docqa2/.wlnotdelete/extract/docqa2_DOC_clusterqa/jarfiles/WEB-INF/lib/coherence.jar!/tangosol-coherence.xml"
2007-11-07 09:49:43.188 Oracle Coherence 3.3.1/389p1 <Info> (thread=Main Thread, member=n/a): Loaded operational overrides from file "/home/www/WEB-INF/lib/tangosol-coherence-override.xml"
Oracle Coherence Version 3.3.1/389p1
Grid Edition: Development mode
Copyright (c) 2000-2007 Oracle. All rights reserved.
2007-11-07 09:49:43.528 Oracle Coherence GE 3.3.1/389p1 <Info> (thread=Main Thread, member=n/a): Loaded cache configuration from file "/home/www/WEB-INF/lib/pub-search-cache-config.xml"
2007-11-07 09:49:43.571 Oracle Coherence GE 3.3.1/389p1 <Info> (thread=Main Thread, member=n/a): sun.misc.AtomicLong is not supported on this JVM; using a synchronized counter. Though safe to ignore, you may upgrade to BEA's 1.5 JVM to fix this issue.
2007-11-07 09:49:44.829 Oracle Coherence GE 3.3.1/389p1 <Warning> (thread=Main Thread, member=n/a): UnicastUdpSocket failed to set receive buffer size to 1428 packets (2096304 bytes); actual size is 89 packets (131071 bytes). Consult your OS documentation regarding increasing the maximum socket buffer size. Proceeding with the actual value may cause sub-optimal performance.
2007-11-07 09:49:45.419 Oracle Coherence GE 3.3.1/389p1 <D5> (thread=Cluster, member=n/a): Service Cluster joined the cluster with senior service member n/a
2007-11-07 09:49:45.555 Oracle Coherence GE 3.3.1/389p1 <Info> (thread=Cluster, member=n/a): Failed to satisfy the variance: allowed=16, actual=47
2007-11-07 09:49:45.555 Oracle Coherence GE 3.3.1/389p1 <Info> (thread=Cluster, member=n/a): Increasing allowable variance to 19
2007-11-07 09:49:46.040 Oracle Coherence GE 3.3.1/389p1 <Info> (thread=Cluster, member=n/a): This Member(Id=2, Timestamp=2007-11-07 09:49:45.69, Address=10.5.176.85:8088, MachineId=48981, Edition=Grid Edition, Mode=Development, CpuCount=4, SocketCount=2) joined cluster with senior Member(Id=1, Timestamp=2007-11-07 09:45:10.205, Address=10.5.176.86:8088, MachineId=48982, Edition=Grid Edition, Mode=Development, CpuCount=4, SocketCount=2)
Could you please explain why it happens, and what should I do to resolve this issues ?
Many Thanks,
Bing

Hi, Gene
Thank you for the response. I will send you our full log files and thread dumps.
I just want to give you more details about our cases :
1. This only happened without starting cache servers (com.tangosol.net.DefaultCacheServer).
2. And our application which are running on weblogic cluster will just call "CacheFactory.getCache("XXX")", and running as the Tangosol DataClient.
3. All weblogic member servers will be up running successfully if our cache servers are up running.
Also I tried to test another case :
Suppose all weblogic instances and cache server instances are up running. Now I trying to restart (kill weblogic instance process and restart) one of the weblogic member, It will up running successfully only if add some sleep times after killing weblogic processes and restarting it. Looks like tangosol cluster need certain time to aware the member has left cluster, then the restart process will be successful.
Questions :
1. Should we start our weblogic cluster only after cache server cluster is up running ?
2. How do we decide how many time we should wait before start new process to join the cache cluster ?
Could you please help to explain this one for me and let us if there anyway we can do to avoid the problem.
Many Thanks !!!
Bing

Creating cluster trying to remove disks.

Hi
I am going through the pain of trying to create a whole cloud environment using scvmm2012r2 so that it can then link in to the whole windows azure pack.
I have created what I think is the whole fabric which has been very very painful.
My question when trying to make all that setup work is the following.
When I try and create a hyperv cluster using scvmm I step through the wizard. First issue I have is:
I have defined a logical switch which has three vnics one for host management 2. Live migration. 3. Cluster workload.
When it comes to giving an ip it is only allowing me to select from the host management pool. I would have thought it should have been the cluster or live migration networks.
2nd question is when it gets to the disks to cluster. The servers are connecting to a fibre channel switch so can see other disks that are attached to other clusters. In the interface I can not untick those I don't want as part of this cluster. What have
I done wrong
in the image I have highlighted the disks that I want to remove but I cannot.
If I do this normally through fail over cluster manager then it is no issue.

Hi.
First thing first: when you create a Hyper-V Cluster, you will also create a Cluster Name Object in Active Directory, this will be the access point of this cluster and this also requires an IP adress. This IP adress is then on the management network - where
clients can access the cluster name object (so that VMM (as a client) can access the cluster - and manage the cluster). this is by design. You would leave cluster network and live migration out of this, as this is for internal cluster communication and live
migration traffic.
second, a cluster should only see the disks it should be using, and not any other disks used by other clusters. You must check your zoning here, as this is not best practice. a CSV can't be shared across several cluster.
I would suggest that you clean that up, and if you don'w want VMM to do this for you, you can create the cluster in failover cluster manager, add the required disks and the update the hosts in VMM so that they reflects the cluster you have created.
-kn
Kristian (Virtualization and some coffee: http://kristiannese.blogspot.com )

How to install sp2 for sql server 2012 , where sql server 2012 instnce is installed in cluster mode

Hi Everyone,
I want to install sp2 for sql server 2012, My sql server 2012 instance is installed in cluster mode.
Please suggest the best practice to install sp2 , what are prerequisite and recommendation.
Please share installation guide for sp2 in cluster instance, if any one have.
Thanks All
Aditya

Did you searched a bit before posting question.
Please read
https://support.microsoft.com/kb/958734?wa=wsignin1.0
http://blogs.msdn.com/b/john_daskalakis/archive/2014/09/05/how-to-install-a-service-pack-at-a-sql-server-2012-failover-instance-best-practices.aspx
http://blogs.msdn.com/b/jason_howell/archive/2012/08/28/how-to-patch-sql-server-2012-setup-with-an-updated-setup-package-using-updatesource-to-get-a-smart-setup.aspx
Please mark this reply as answer if it solved your issue or vote as helpful if it helped so that other forum members can benefit from it
My Technet Wiki Article
MVP

Creating Cluster Fails

When using VMM 2012 R2 to create a cluster we are receiving this error. It goes all the way to step 1.5 Create Cluster and then throws this error. In the past we have created clusters with Failover Clustering and added them back into VMM but
would really like to get VMM to do what it says it can do.
Error (25325)
The cluster creation failed because of the following error: The network name '' is already used in the network..
Recommended Action
Please refer to cluster documentation for resolving cluster problems.
Is VMM trying to write to DNS? We have a DNS name reserved for the cluster address in Infoblox already. What other steps should we try? Our storage is coming from our SAN (IBM V7000) with Fiber and the hosts have the latest SDDDSM installed.
I am stumped currently.

Hi Sir,
>> I changed the DNS IP as for some reason the old IP was responding to ping so will have to track that down.
How are things going now ?
Best Regards,
Elton Ji
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected] .

Error while creating cluster view

Hi all,
Requirement is to create cluster view copying cluster view VC_TABWU01 into custom view.
CV VC_TABWU01 has two data base views V_T093C_10 and V_T093U_01 I copied them both in to ZT093U_01 and ZT093C_10 and created a CV Z_TABWU01. Field dependence is set, when I am activating view I am getting message that screen 300 of ZT093U_01 is modified. I changed all possible options as standard view, kindly help me activating cluster view.
Error: The flow logic of the screen ZT093U_01 0300 is not that of a generated view maintenance list screen. Either the screen has been considerably modified manually, or the view which it is based on has no maintainable key.
Thanks
Krishna.

Need to add events in TMG. Solved with help of standard CV

Pls help in creating cluster view

Pls help in creating cluster view
regards
jindow

Hi,
Please try this and use BSEG as an example.
1. Go to SE12.
2. Enter BSEG
3. Click Display button
4. Go to Delivery and Maintenance' tab.
5. You should be able to see Pool/cluster RFBLG.
6. Double click RFBLG and then click Where-Used list button (CTRLSHIFTF3).
7. Select Table option and click Execute button.
8. System will show all the table that belong to this pool/cluster.
For Pool/Cluster REGUC, it is only used in table REGUP.
Look at the below link
Re: Define view for cluster table?
Regards,
Priyanka.

Problem with APEX 4.0 - "ORA-20001: Error with: GRANT CREATE CLUSTER "

I have a workspace which I've succesfully created with schema A.
However when i try to assign an additional schema to it, schema B, I get the following error message :-
"ORA-20001: Error with: GRANT CREATE CLUSTER TO "BI_SOURCES" ORA-01031: insufficient privileges"
i've tried granting "create cluster with admin option' to users A,B,anonymous AND APEX_040000. FLOWS_030000 already has these privileges.
Anybody any ideas ?
regs
johnnie
Edited by: johnnie d on 31-Aug-2011 10:58

I have experience the similiar problem. The error message: Invalid exist/not exist condition: ORA 2001 Query must begin with Select or With.
I have home page and concept review report page below home page. And Concept review form under the report page. The error is display in all of the three pages. I checked carefully and still not able to find where the error come from. Can you please help? All the report region and form region have the select statement, is it from the LOVs? Home
Concept review report
Concept reveiw Form(for detail info)
Thank you!

Can u create cluster and pooled tables in real time

hi
can u create cluster and pooled tables in real time.can u send data base tables name of above one.

Hai Anil
For creating cluster tables first u have to create table pool ...
create a table and specify the fields and other tecnical settings and
then Goto EXTRAS --> Change Table Category and selct the Pooled table and activate it...
Then Create another table And specify the required fileds and also the settings and then
Goto EXTRAS --> Change Table Category and selct the Cluaster table and in Delivery and
Maintainence Properties mention the Pooled table that u created and activate it...
Regards
Sreeni

2012 R2 Cluster - Issues creating cluster

Similar Messages

Maybe you are looking for