2800 Multilink Problem

Hello,
We 've got a dial problem with a 2811 branch router (ISDN2) and a 7206 central router (2*ISDN30)
Wehn the 2800 dials in no problem.
When threshold comes up no problem.
But when the second B-channel closed the 2800 doesn't route trafic any more.
Routing protocols still work.
Extended ping from the routers FE interface to de central location form.
But a device connected to the FE interface cannot ping the remote site.
When i use IOS
c2800nm-advsecurityk9-mz.124-10.bin : FAILTY
c2800nm-advsecurityk9-mz.124-12.bin : FAILTY
c2800nm-advsecurityk9-mz.124-5.bin : OKE
c2800nm-advsecurityk9-mz.124-8a.bin : OKE
Branch router:
interface BRI0/2/0
no ip address
encapsulation ppp
dialer pool-member 1
isdn switch-type basic-net3
isdn tei-negotiation first-call
isdn point-to-point-setup
ppp authentication chap
end
interface Dialer10
ip address 1.1.1.1 255.255.255.252
ip pim sparse-dense-mode
encapsulation ppp
dialer pool 1
dialer string 0123456789
dialer load-threshold 75 either
dialer max-call 2
dialer-group 1
no cdp enable
ppp authentication chap callin
ppp chap hostname somerouter
ppp chap password <REMOVED>
ppp multilink
end
Central router:
interface Dialer1
description ISDN:
bandwidth 128
ip address 1.1.1.2 255.255.255.252
ip pim sparse-dense-mode
encapsulation ppp
ip summary-address eigrp 1 0.0.0.0 0.0.0.0 180
dialer pool 1
dialer remote-name someroute
dialer idle-timeout 180
dialer-group 1
no fair-queue
no cdp enable
ppp authentication chap
ppp multilink
end

Hi
Have you checked up the routes for the remote destinations when the second channel is down ?
Can you check whether you are getting any routes available through the live BRI Channel available when the other one goes down ?
Also can you verify whether the channel is stil active using show isdn active command ?
regds

Similar Messages

Ppp multilink problem

Hi
I am having a problem configuring ip rtp with interleaving on two 1721's prioritizing voice traffic between two ip voice devices over a 128k point to point link. This is my config...
interface Multilink1
ip address 192.168.24.2 255.255.255.0
no cdp enable
ppp multilink
ppp multilink fragment delay 20
ppp multilink interleave
ppp multilink group 1
ip rtp header-compression iphc-format
ip tcp header-compression iphc-format
ip rtp priority 8100 100 40
interface Serial0
bandwidth 128
no ip redirects
no ip unreachables
no ip proxy-arp
encapsulation ppp
ppp multilink
no cdp enable
Everytime I add the 'ppp multilink' to the serial, I get the virtual-access interface bouncing up and down with no traffic flowing.
any ideas?

Cannnnnnnnt see much wrong, try adding "ppp multilink group 1" to int S0 config.

Multilink problem with MPLS

we are having two multilink on a router and we are using ldt between those.but we are having drops in the multilink.can anyone guide me.
shivlu

Add the folllowing Configuration on Router-1 and Router-3 Respectively:
R1 Configuration:
router bgp 1
no synchronization
bgp log-neighbor-changes
neighbor 3.3.3.3 remote-as 1
neighbor 3.3.3.3 update-source Loopback1
neigbor 33.33.33.33 remote-as 1
neighbor 33.33.33.33 update-source loopback11
no auto-summary
address-family vpnv4
neighbor 3.3.3.3 activate
neighbor 3.3.3.3 send-community extended
neigbor 33.33.33.33 activate
neigbor 33.33.33.33 send-community extended
exit-address-family
address-family ipv4 vrf os
redistribute connected
redistribute static
no auto-summary
no synchronization
exit-address-family
|
|
ip vrf os
rd 1:1
route-target export 1:1
route-target import 1:1
bgp next-hop 33.33.33.33
R3 Configuration:
router bgp 1
no synchronization
bgp log-neighbor-changes
neighbor 1.1.1.1 remote-as 1
neighbor 1.1.1.1 update-source Loopback3
neighbor 11.11.11.11 remote-as 1
neighbor 11.11.11.11 update-source Loopback33
no auto-summary
address-family vpnv4
neighbor 1.1.1.1 activate
neighbor 1.1.1.1 send-community extended
neigbor 11.11.11.11 activate
neighbor 11.11.11.11 send-community extended
exit-address-family
address-family ipv4 vrf os
redistribute connected
redistribute static
no auto-summary
no synchronization
exit-address-family
ip vrf os
rd 1:1
route-target export 1:1
route-target import 1:1
bgp next-hop 11.11.11.11
This Way, all your VPN Traffic Sourced from R5 Will transit the path of the TE tunnel to reach R4.
Regards,
Mohamed

Acer 2800 Imaging Problem

when trying to type the IMG command at the bash promt i recieved command
not found, also after the Linux kernal loads it displays a message
stating that the Network card is not supported.
I am using ZENworks for Desktop 4, maybe it doesn't have linux drivers.
Any help???
Amer

> I am using ZENworks for Desktop 4, maybe it doesn't have linux drivers.
The latest and greatest? Sp1 + ir7? What type of NIC? Note that there is
a special forum 4x and 3x imaging for imaging issues.
- Anders Gustafsson, Engineer, CNE6, ASE
NSC Volunteer Sysop
Pedago, The Aaland Islands (N60 E20)
Novell does not monitor these forums officially.
Enhancement requests for all Novell products may be made at
http://support.novell.com/enhancement
Using VA 5.51 build 315 on Windows 2000 build 2195

Mobile newcastle(2800+, 35W) problems w/ k8n np

Got my system all set up yesterday and here is the current state of affairs, at least until MSI releases a new bios. The bios wont boot any higher than at a Vcore of .90V. According to clockgen, the max vcore is 1.25V. Using Clockgen along with a VCore of 1.25 the max cpu multiplier is 6.5, other wise a blue screen shows up saying that windows is shutting down to prevent damage, this is probably due to the board's messed up temperature monitoring system. Anybody have any thoughts, other than MSI really needs to get a new bios out pronto.

Importing from Eudora problems - html messages being displayed in plain text and problems with attachments

Hello,
I hope you can help me. I've imported all my emails from Eudora into Outlook 2010 but I have a couple of problems.
All emails that I've imported which had attachments with them have a notice on them saying the attachment has been blocked. I can always browse to the folder whereb my old attachments are stored, but this is still inconvenient.
Secondly, all my messages that I've sent in the past (html) are being displayed in plain text, which is making them difficult to read because of all the html tags being displayed.
Also with emails that I've sent in the past- there is no record of any attachments being sent with messages which I know had attachments with them.
Any ideas? I've trawled google and had no luck except finding programs that cost $70 that can import everything properly.
David

David:
I know this is a very old thread, but did you every figure out a way to fix the formatting of imported Eudora mail?
I just "upgraded" from Eudora to Outlook 2010 ...
and have 10 years worth of HTML formatted e-mail that now shows up as plain text with embedded html formatting ...
apparently it is a long-running problem that has roots in the way Eudora formats messages ...
Outlook and other e-mail clients all seems to have issues with importing and do not properly recognize HTML-formatted messages from Eudora ... very sad that I can no longer really "read" my old e-mail at this point ... :-(
See closing paragraphs here: http://its.uiowa.edu/support/article/2800
Same problem over at Mozilla going back 10+ years ... not sure if they fixed it..........
https://bugzilla.mozilla.org/show_bug.cgi?id=3157

K7N2G-ILSR need serious help!!

OK, Ive had my K7N2G-ILSR running perfect for nearly a year. It came out of my gaming rig to do duty in my server a few months ago and always ran perfect. 6 weeks ago, I started changing my configuration, I went from a Gainward FX5900 NU to a Radeon 9800 Pro to an MSI FX5900Ultra, and added a Winfast TV2000XP expert, and swapped in a 2800+. It seems as if after I swapped in the 2800+ the problems began. Constant BSOD under use and Memtest86 would lock, never give me errors, just locked. I RMAd the board and got my replacement this weekend. I installed it and almost the exact same problems. In the interim, while the K7N2G was away at RMA camp, I picked up a KT6 Delta LSR and used it in its stead. Same processor, PSU, DDR, HSF, Video card, Tunercard, case and cables. It ran absolutley flawless. I was watching TV on the tuner while browing the web and unRARing a 4.5GB movie file without the slightest hint of trouble.
Now, With the replacment K7N2G in, some days I can Memtest86 for 2 hours without a problem, and sometimes it will not go past the "moving 64K block" section. There is no rhyme or reason as to when it will or wont lock. I got into my original windowsXP installation, and tried to run Prime95. Error, BSOD and another BSOD. Then one day, it ran for 1-1/2hours Prime95 perfect. ?!?!? I have tried the following, and have not found a stable setup yet. I dotn want to go back to the KT6 LSR, because I need my Soundstorm and I like dual channel Nforce. Heres everything I have tried.
Downclocked to 133FSB - stable sometimes.
Switched to Single Channel and relaxed timings - no difference.
Removed video card and tuner card - no difference.
Ran single stick of DDR - no difference.
Tested HDD twice - no errors.
Tested HDD on KT6 Delta LSR - ran PERFECT.
Tested DDR on NF7-S and KT6 Delta LSR - ran PERFECT.
Tested 2800+ on same 2 boards - ran PERFECT.
Tested FX5900U on same 2 boards - ran PERFECT.
Disabled FW and AGP8X- no difference.
Tried Onboard Vid - no difference.
Tried MSI FX5200 64MB - no difference.
Upped core and DDR voltage - no difference.
BIOS Safe defaults - no difference.
Cleared CMOS and ran at defaults - no difference.
Checked and rechecked mounting (though the first ran perfect in same case for 8 months)
The only thing left would be the PSU, but it seems hightly unlikely that it would be the culprit, it is only 6 months old. it is a 430W Thermaltake Silent Purepower. I built a system for a friend, nearly identical except his has an 80GB HDD and 9600XT. I recently swapped a 3 year old PP303X Antec 300Watt PSU without P4 connector into his because his cheap Raidmax 400 blew out, and the Antec runs his system rock solid. The temps in my system are right on, 45C CPU Loaded, 32C Case loaded. CPU is cooled by a Vantec Aeroflow w TMD. What the hell is going on here? My level of expertise is high. this is the first system ihave not been able to troubleshoot. I dont want to get stuck with an Nforce2 board sitting on my shelf in its box, and I cant afford to replace it. HELP!!!!

Basically yes, I took everything apart when i installed the KT6 Delta, and when I got my K7N2G back from RMA, I cemoved everything, cleaned the case and reinstalled it all.
When the K7N2G was running rock solid, I was running a 2500+ barton. When I swapped my 2600+ in, after I had the instability with the 2800+, the system seemed more stable, but still had trouble. I wish I had my 2500+ back to test it out, but its long gone. I am using the latest BIOS, 1.8 or 1.9, I forget which, and the one I got back from RMA has the latest BIOS on it as well.
I am really beginning to beleive that my PSU is flaky, and I'm waiting for a friend to borrow me his 350W Antec so I can test the PSU theory. Im still open to suggestions!!

Satellite 2800-400 sound card driver problem with XP-SP2

I have upgraded my Satellite 2800-400 to XP-SP2 and my sound card driver does aperently not work with SP2. I have downloaded the latest driver that I can find and that is 5.12.1.5245 from 2002, but this driver does not work together with the program Skype. I get a massage that the sound card driver does not suport SP2.
How can I solve this problem without deleting the SP2 upgrade.
Message was edited by: felixnorway

I have tried both drivers and the same problem ocurs.
After ecessive testing I have found out that everything/skype now works well for 1-2 hours. Then sudenly my compter does something (I do not now what, and I can not se that the computer does anything) and then sudenly Skype starts beeing blocked by SP2. At the same time (same minute) that Skype after 1-2 hours of perfec running sudenly is beeing blocked, my computer somehow have loaded a file named kernel32.dll for the second time. How i found out this is just a coinsidence, no errors indicates this file beeing involved and this is maybe normal. The file is located at C/Windows/system32/kernel32.dll. Do you know what my comuter does after this amount of time and why it loads this file for a second time. When I turn on my comuter the file is loaded and that is logical, but after 1-2 hours what is the logic for the computer to load it again. Is this something I can shutt off?
My computer runs perfect and smoth for 1-2 hours, then I beliwe the whole system32 is loaded again and this causes some kind of problen and makes the SP 2 kick in.
Any advice?

KT6V and sempron 2800 problem

I have updated the bios to the latest version, but if i set the fsb to 166 the conputer fails as it starts to load windows, it doesnt display the correct information in post.
if i set it to 133 and run it as a 2300 (i think) it runs fine, but at 62c on idle!!!!!
any idea what may be going wrong here. i am going to do some more trouble shooting using my hardware which is kinda simliar, but i would rather not have to go through that hassle.
david.

yeah it was on back to front, i am hating myself for that, it is down to the low 50s. still high but its really hot where i live.
i still cant put the fsb up to 166 to run it as a 2800. but ill work on it more when i can swap bits with my hardware.
anyone else had the problem.
thanks.

Multilink PPP problem

Hi Guys,
i got a situation here and hope someone will be able to help me out. Recently i configured a PPP multilink and am facing some issues after that.
Issue 1:
There seems to be lot of input error on multilink interface (150 errors in 40 mins)
Issue 2:
when any of the multilink member interface goes down (all other links are active), am getting packrt drops and request timed out when i ping my other end multi link interface atleast for some 30 sec , after which my response is ok.
About my network
I have connectivity between site A and Site B which consists of five 64 kbps Leased lines bundled together with Multilink PPP
My configuration is shown below
End A
interface multilink 1
ip address x.x.x.x x.x.x.x
ppp multilink fragment-delay 20
ppp multilink interleave
ppp multilink
multilink-group 1
int Ser 2/0
bandwidth 64
no ip address
no ip redirects
no ip proxy-arp
encapsulation ppp
no ip route-cache
no ip mroute-cache
no fair-queue
ppp multilink
multilink-group 1
int Ser 2/1
bandwidth 64
no ip address
no ip redirects
no ip proxy-arp
encapsulation ppp
no ip route-cache
no ip mroute-cache
no fair-queue
ppp multilink
multilink-group 1
int Ser 2/2
bandwidth 64
no ip address
no ip redirects
no ip proxy-arp
encapsulation ppp
no ip route-cache
no ip mroute-cache
no fair-queue
ppp multilink
multilink-group 1
int Ser 2/3
bandwidth 64
no ip address
no ip redirects
no ip proxy-arp
encapsulation ppp
no ip route-cache
no ip mroute-cache
no fair-queue
ppp multilink
multilink-group 1
int Ser 2/4
bandwidth 64
no ip address
no ip redirects
no ip proxy-arp
encapsulation ppp
no ip route-cache
no ip mroute-cache
no fair-queue
ppp multilink
multilink-group 1
End B
interface multilink 1
ip address ip address x.x.x.x x.x.x.x
ppp multilink fragment-delay 20
ppp multilink interleave
ppp multilink
multilink-group 1
interface S 2/0:1
bandwidth 64
no ip address
no ip redirects
no ip proxy-arp
encapsulation ppp
no ip route-cache
no ip mroute-cache
no fair-queue
ppp multilink
multilink-group 1
interface S 2/0:11
bandwidth 64
no ip address
no ip redirects
no ip proxy-arp
encapsulation ppp
no ip route-cache
no ip mroute-cache
no fair-queue
ppp multilink
multilink-group 1
interface S 2/0:25
bandwidth 64
no ip address
no ip redirects
no ip proxy-arp
encapsulation ppp
no ip route-cache
no ip mroute-cache
no fair-queue
ppp multilink
multilink-group 1
interface S 2/0:4
bandwidth 64
no ip address
no ip redirects
no ip proxy-arp
encapsulation ppp
no ip route-cache
no ip mroute-cache
no fair-queue
ppp multilink
multilink-group 1
interface S 2/0:6
bandwidth 64
no ip address
no ip redirects
no ip proxy-arp
encapsulation ppp
no ip route-cache
no ip mroute-cache
no fair-queue
ppp multilink
multilink-group 1

pls find the output of show command
END A #sh int multilink 5
Multilink5 is up, line protocol is up
Hardware is multilink group interface
Description: ***Multilink to End B ***
Internet address is 192.26.0.162/30
MTU 1500 bytes, BW 320 Kbit, DLY 100000 usec,
reliability 255/255, txload 2/255, rxload 1/255
Encapsulation PPP, loopback not set
Keepalive set (10 sec)
DTR is pulsed for 2 seconds on reset
LCP Open, multilink Open
Open: IPCP, CDPCP
Last input 00:00:00, output never, output hang never
Last clearing of "show interface" counters 19:55:13
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 2000 bits/sec, 4 packets/sec
5 minute output rate 3000 bits/sec, 4 packets/sec
309478 packets input, 58763590 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
1492 input errors, 0 CRC, 1492 frame, 0 overrun, 0 ignored, 0 abort
290606 packets output, 32728691 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
END A #sh ppp multilink
Multilink5, bundle name is End B
Bundle up for 22:06:31
493 lost fragments, 162050 reordered, 0 unassigned
999 discarded, 0 lost received, 3/255 load
0xAE5E6 received sequence, 0x69F6B sent sequence
Member links: 5 active, 0 inactive (max not set, min not set)
Se2/0, since 20:07:34, last rcvd seq 0AE5E1, 160 weight, 152 frag size
Se2/2, since 20:04:45, last rcvd seq 0AE5E2, 160 weight, 152 frag size
Se2/3, since 20:04:07, last rcvd seq 0AE5E3, 160 weight, 152 frag size
Se2/5, since 20:03:24, last rcvd seq 0AE5E4, 160 weight, 152 frag size
Se2/1, since 19:57:12, last rcvd seq 0AE5E5, 160 weight, 152 frag size
Am getting 1400 input errors in last 19 hours on multilink interface, also less than 100 input errors on member serial interfacs.Also am not loosing any link member.

I have asr 1000 with asr1000rp2-adventerprisek have problem when I gave PPP Multilink to the interface Dialer

Hello,
please Urgent Help
I have ASR 1000 with asr1000rp2-adventerprisek Version, when I give PPP Multilink to the dialer interface it show following error :
FMFP-3-OBJ_DWNLD_TO_CPP_FAILED: F0: fman_fp_image:
MLP bundle , link download to CPP failed
please urgent help

this error comes with the command PPP multilink, it is a lot of letters and numbers and then this last line comes this message
FMFP-3-OBJ_DWNLD_TO_CPP_FAILED: F0: fman_fp_image:
MLP bundle 181, link 178 download to CPP failed
the configuration still not installed but I configured just the following lines
interface Virtual-Template
ip unnumbered Loopback2
ip mtu 1440
ip load-sharing per-packet
ip tcp adjust-mss 1400
no logging event link-status
peer default ip address pool
ipv6 unnumbered Loopback2
ipv6 enable
no ipv6 nd suppress-ra
ppp authentication pap chap callin
ppp multilink
ppp multilink fragment delay 100
ppp multilink mrru local 1546
that were the lines used to configure this Dialer, the image must be asr1000rp2-adventerprisek and not Ipbase but I dont tried to use IPbase.
what do think ?

KT3V Problem with CPU Sempron 2800+

Need help to configure my new CPU Sempron 2800+ in my motherboard KT3V. I have upgrade Bios but work 1900. i set Mhz to 166 and now work 2400+. Any body help plzzzzz

Make sure you have the latest bios update so it will recognize the sempron.
Windows may still try to read it as an old Thoroughbread even though it is not.
Just use CPU-z to make sure your getting Sempron clock speeds (2800+ Sempron is 2.0ghz i beleive) and that it recognizes all of the 256 L2 cache.

Cisco 2800 series vista problems

One of my customers use Cisco 2800series router and the problem that i have is that i connect a new notebook to the network, cisco is working as dhcp server. he gives me my ip, dns as it should be, my comunnication between pc's in office work normaly but when i try internet it dosent work, cant ping anything outside and diagnose option on vista says my dns is wrong. when i connect it to any other network it works fine

sience my firm is not responsible for that part of maintance i have no accsess to the device but i guess sience its been set up by ppl that are considered to be professionals i would guess its set up correctly.
pc's on xp have no problem connecting to internet via lan or wlan.
also if this might help abit, few weeks back they tried to connect new mac to the same network and mac had identical problem. im not femiliar with mac but i was told it was the newest O.S for mac (dont ask for names Mac's are somewhat of a big minority :)

[VIA] Problem with kt3 ultra 2 and 2800+ Barton

Please help. I've a 2800+ barton on my motherboard 6380E with bios 5.7 But my processor is recignized as a 2500+.
In the bios, my Fsb is 166 and all the rest is on auto. I've 1,5 GB memory pc2700 333 mhz.
I'm trying to force 12.5/13 in bios but it stay as 11.5 (saw with cpuz). What can i do to have the 2800+ recognized with this motherboard ? Help !!! I've change the FSB to 180, but with cpu-z, the processor is still a 2500+

You could try WCPUID, which can also determine the cpu that you have.
http://hp.vector.co.jp/authors/VA002374/src/download.html
Failing that as Wonkanoby said check the codes on the cpu itself.
Perhaps as an alternative just try raising the FSB from 166 to 167. Upon boot instead of the bios detecting the cpu, it will give you the clock speed albeit at 167. Since you have the multiplier you can then work out the clock speed at 166, if you see what I mean and determine (or have a better idea) of the cpu that you have.
Good Luck

Problem with K7N2Delta2 LSR and Sempron 2800+

Well.., yesterday at friends house, i decieded to push more my overclock (Stable was 200x11, 1.75v vCore), so i started playing around..., got the vCore to 1.8, the PC to 225x11 with rams running at aprox 110mhz (cant remember 100%, since they wouldnt run at 225), so... it booted up, i was on windows happy, transfering some files over lan, and decieded to burn a dvd..., now when that dvd was at about a 52% pc got stuck..., brrp..., i reseted it assuming it just wasnt stable..., but after that reset it wouldnt EVEN show the Bios windows (not the bios setup, but when its detecting ide, it shows your ram, procesor etc), i said [content edited]!!!, of course i proceded to Clear CMOS, but nothing happened..., as far as i know this mobo got a very strange way to reset the FSB, and its starting the pc while you pressing the key "Insert", it worked a few times when the FSB was at 210, 215, 220, (with rams @ 1:1), and it reseted just fine..., but this time it wont...
After some hours, and over my house, i started playing around trying to make it boot, and it booted once..., but i reseted to plug all back in (Ide, Sata, etc), and it wouldnt boot up again ><..., i removed Sata, Ide, and everything i plugged in and nothing..., last night i removed the jumper, the battery and disconnected the pc from the Energy source, and nothing this morning...., im really out of ideas, some people think its a Corrupt Bios, other thinks Procesor is gone, but i dunno what to think..., im thinking on flashing the bios on a friends house (who got same mobo), but i wanna be 100% sure of what the [content edited] i can be...
Sempron 2800+
MSI K7N2 Delta2 LSR
2x256 Kingston Valueram PC3200
Generic 350W PSU
Waiting for some ansewrs...
Greets.
Dom?

"...On 12v i got 12.3, on 5v i got 5.2, and i don't know the other..." You were asked about the AMPS that P.Su. gives to 3.3v. 5v. and 12v. rails, not about the voltage, that is almost the same in every P.Su. You'll find it printed on P.Su. side. And please, read carefully what the people trying to help, is asking you, so you can answer what is asked, and not other things.
"...the PC to 225x11 with rams running at aprox 110mhz..." Do you consider this runing 1:1 ?
"...but im pretty sure that one night without battery and connected to no PSU would discharge it no? No. The power that remains on the system could be enough to give power to Bios during a night.

2800 Multilink Problem

Similar Messages

Maybe you are looking for