Cisco 2800 series vista problems

One of my customers use Cisco 2800series router and the problem that i have is that i connect a new notebook to the network, cisco is working as dhcp server. he gives me my ip, dns as it should be, my comunnication between pc's in office work normaly but when i try internet it dosent work, cant ping anything outside and diagnose option on vista says my dns is wrong. when i connect it to any other network it works fine

sience my firm is not responsible for that part of maintance i have no accsess to the device but i guess sience its been set up by ppl that are considered to be professionals i would guess its set up correctly.
pc's on xp have no problem connecting to internet via lan or wlan.
also if this might help abit, few weeks back they tried to connect new mac to the same network and mac had identical problem. im not femiliar with mac but i was told it was the newest O.S for mac (dont ask for names Mac's are somewhat of a big minority :)

Similar Messages

Trying to Download a Software Image to Cisco 2800 series router through TFTP Using the tftpdnld ROMmon Command

Trying to Download a Software Image to Cisco 2800 series router through TFTP Using the tftpdnld ROMmon Command
and I am getting an Error , I cant figure out what I am doing wrong. I have also pasted my display down here can someone help me out, thanks in advance, I am still new to this utility.
My questions are How do you direct this utility to point to the desktop or the TFTP folder
does FE_PORT: Fast Ethernet 0 imply or point to Fa0/0 on my router
My router is suppose to have 10.0.0.3 255.0.0.0
Gateway of 10.0.0.1 255.0.0.0
My TFTP Server 10.0.0.2 255.0.0.0
How do I get the MAC address of the Router or the TFTP Server and which one is required?
my Ethernet port is 100Mb/Sec I cant tell whether it is full duplex or not so How do i set this FE_SPEED_MODE: Auto???
=====================================================================================
rommon 10 >
rommon 10 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
?=0
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
TFTP_FILE=
rommon 11 > TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
rommon 12 > TFTP_CHECKSUM=0
rommon 13 > SET
monitor: command "SET" not found
rommon 14 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
?=0
TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
TFTP_CHECKSUM=0
rommon 15 > tftpdnld
          IP_ADDRESS: 10.0.0.3
      IP_SUBNET_MASK: 255.0.0.0
     DEFAULT_GATEWAY: 10.0.0.1
         TFTP_SERVER: 10.0.0.2
           TFTP_FILE: c2800nm-adventerprisek9-mz.124-24.T4
        TFTP_VERBOSE: Progress
    TFTP_RETRY_COUNT: 18
        TFTP_TIMEOUT: 7200
       TFTP_CHECKSUM: No
        TFTP_MACADDR: 30:37:a6:49:35:a8
             FE_PORT: Fast Ethernet 0
       FE_SPEED_MODE: Auto
Invoke this command for disaster recovery only.
WARNING: all existing data in all partitions on flash: will be lost!
Do you wish to continue? y/n: [n]: y
ARP: address resolution for 10.0.0.2 timed out.
ARP failed with failure code 1. TFTP transfer aborted.
TFTP: Operation terminated prematurely.
rommon 16 >       " not found
rommon 17 >FE_SPEED_MODE=2
variable name contains illegal (non-printable) characters
rommon
rommon 18 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
TFTP_CHECKSUM=0
?=0
rommon 19 > tftpdnld [ur]
usage: tftpdnld [-hr]
Use this command for disaster recovery only to recover an image via TFTP.
Monitor variables are used to set up parameters for the transfer.
(Syntax: "VARIABLE_NAME=value" and use "set" to show current variables.)
"ctrl-c" or "break" stops the transfer before flash erase begins.
The following variables are REQUIRED to be set for tftpdnld:
            IP_ADDRESS: The IP address for this unit
        IP_SUBNET_MASK: The subnet mask for this unit
       DEFAULT_GATEWAY: The default gateway for this unit
           TFTP_SERVER: The IP address of the server to fetch from
             TFTP_FILE: The filename to fetch
The following variables are OPTIONAL:
          TFTP_VERBOSE: Print setting. 0=quiet, 1=progress(default), 2=verbose
      TFTP_RETRY_COUNT: Retry count for ARP and TFTP (default=18)
          TFTP_TIMEOUT: Overall timeout of operation in seconds (default=7200)
         TFTP_CHECKSUM: Perform checksum test on image, 0=no, 1=yes (default=1)
          TFTP_MACADDR: The MAC address for this unit
               FE_PORT: 0= (default), 1
         FE_SPEED_MODE: 0=10/hdx, 1=10/fdx, 2=100/hdx, 3=100/fdx,
                        5=Auto (default)
      TFTP_DESTINATION: The flash destination device for the file
                        flash:(default), usbflash0:, usbflash1:
Command line options:
   -h: this help screen
   -r: do not write flash, load to DRAM only and launch image
rommon 20 > tftpdnld
          IP_ADDRESS: 10.0.0.3
      IP_SUBNET_MASK: 255.0.0.0
     DEFAULT_GATEWAY: 10.0.0.1
         TFTP_SERVER: 10.0.0.2
           TFTP_FILE: c2800nm-adventerprisek9-mz.124-24.T4
        TFTP_VERBOSE: Progress
    TFTP_RETRY_COUNT: 18
        TFTP_TIMEOUT: 7200
       TFTP_CHECKSUM: No
        TFTP_MACADDR: 30:37:a6:49:35:a8
             FE_PORT: Fast Ethernet 0
       FE_SPEED_MODE: Auto
Invoke this command for disaster recovery only.
WARNING: all existing data in all partitions on flash: will be lost!
Do you wish to continue? y/n: [n]: y
ARP: address resolution for 10.0.0.2 timed out.
ARP failed with failure code 1. TFTP transfer aborted.
TFTP: Operation terminated prematurely.
rommon 21 >

What I notice in the original post is this error
ARP: address resolution for 10.0.0.2 timed out.
which says that the router is looking for the 10.0.0.2 server but not getting response to its arp request. Can the original poster clarify for us how the device that has the image file is connected to the router that has the problem? Also what kind of device is 10.0.0.2? Is it a PC running TFTP server software or is it something else?
HTH
Rick

Can I use Sandisk Compact 4GB Flash card on Cisco 2800 series Routers

Can I use Sandisk Compact 4GB Flash card on Cisco 2800 series Routers

Yes can confirm the Sandisk Compact 4GB Flash Card works in 2800 series, the exact card above...
Initially I attempted to shrink the partition on the card to a 2GB FAT partition using the steps here http://timescience.wordpress.com/2010/08/09/how-to-downsize-a-4gb-compact-flash-card-to-2gb/
However when I inserted it into the router and tried a directory list it wouldn't have a bar of it...
*Jun 23 14:11:01.391: %FILESYS-5-CF: CompactFlash insertedrtrvoip#dir flash:%Error opening flash:/ (Invalid DOS media or no media in slot)rtrvoip#format flash:
So I ended up running a format flash and voila, 4GB of flash memory no problems...
rtrvoip#format flash:Format operation may take a while. Continue? [confirm]Format operation will destroy all data in "flash:". Continue? [confirm]Writing Monlib sectors....Monlib write completeFormat: All system sectors written. OK...Format: Total sectors in formatted partition: 7812945Format: Total bytes in formatted partition: 4000227840Format: Operation completed successfully.Format of flash: completertrvoip#dir flash:Directory of flash:/No files in directory3999793152 bytes total (3999793152 bytes free)

Please help me in configuring a Cisco 2800 series router!

Hi! I have to configure a new router with a static route. No routing protocol will be used. I just have to set default route on it and NAT. My senior Network Engineer has asked me to configure this router. There's an apartment where our Overseas employees stay, earlier this apartment had a broadband connection which was further divided through the APs(Cisco Wireless Access Points) and made usable to around 20 users. Now, they have bought in their own lease line and I have to configure this router. We just have to connect it with the ISP using Ethernet (not serial link). I would be so so grateful if you can just type in complete configuration for this. Thanks a ton in advance!

Hi There,
Thanks for your great help!
Below is the final template which my NE provided me:
Now I have to configure this router and then further need to connect various workstations with the same network. Please let me know what needs to be done further.
Thanks!
Configuration:::
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
ip domain-name CVT.net
logging buffered 128000 informational
logging console errors
logging monitor notifications
no aaa new-model
clock timezone IST 5 30
ip cef
no ip domain lookup
username aptadmin secret
enable secret
crypto key generate rsa
ip ssh time-out 60
ip ssh authentication-retries 2
ip ssh version 2
service dhcp
ip dhcp pool LAN-POOL
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server 8.8.8.8 4.2.2.2
domain-name CVT.net
lease 1
interface FastEthernet0/0
description *********Spectranet WAN*********
ip address x.x.x.x 255.255.255.252
load-interval 30
duplex full
speed 100
ntp disable
no cdp enable
interface FastEthernet0/1
description Connect to LAN
ip address 192.168.1.0 255.255.255.0
no ip redirects
duplex auto
speed auto
ntp disable
ip forward-protocol nd
no ip http server
no ip https server
control-plane
banner exec $
Network Provided by CVT
This system is restricted to authorized individuals. Unauthorized access is a
criminal violation of the law and is subject to prosecution. Please disconnect
if you are not an authorized individual. Otherwise, you will be prosecuted
to the full extent of State and Federal law.
All connections and changes are logged.
************** Warning - Warning - Warning **************
$
banner login $
Authorized Associates only! Please disconnect your connection if
you are not an authorized Associate. Otherwise, you will be
prosecuted to the full extent of State and Federal law.
All connections and changes are logged.
$
line con 0
exec-timeout 15 0
password 7
login local
line aux 0
exec-timeout 15 0
password 7 C@pt
login local
line vty 0 4
access-class 50 in
exec-timeout 5 0
login local
transport preferred ssh
transport input ssh
line vty 5 15
access-class 50 in
exec-timeout 5 0
login local
transport preferred ssh
transport input ssh
end

Cisco 1700 series startup problem

I have a cisco 1700 .After a blackout this router is not configured. After recounfigured router save running-config in startup-config and works fine until new blackout. Any idea ?
Thanks (sorry for my english)

Does it also do the same when you power cycle the router.
Sounds like your conf register is not set correctly.
Do a "show system" and look for "Configuration register is 0x2102" at the bottom of the output.
If its not set to this then you can change it by issuing:
my_router(config)#config-register 0x2102
HTH
PJD

How Do I Configure A WRT54G to Work With A Cisco 2800 Router

I'm helping my dad set up a new network. He has a Cisco 2800 series router that connects to the internet via two T1 lines. From this connection, he supplies internet service to his customers. The router was installed and configured with help from AT&T who monitors the router and advises my dad if there are problems.
The Cisco 2800 is not my reason for posting.
He wants to connect his home computers to the 2800. He has one desktop and two wireless laptops and wants to use a WRT54G to connect those computers to the 2800 router. How should he configure the WRT54G to connect to the 2800?
Thanks!

That's what I thought. So it is really no different than connecting the WRT to a DSL modem or cable modem as far as the setup goes. Good then.
Now, next question;
Would this network setup be correct?
Connect a 5-port switch to the 2800
Connect the WRT54G to the 5-port switch.
Configure the laptops to connect throught the WRT54G.
Connect the desktop (Ubuntu 9.10) to the 5-port switch via Ethernet cable (bypass the WRT54G).
Would there be IP conflicts or domain problems? I ask this because this is how his LAN is presently setup and he seems to be getting random connectivity problems on his Ubuntu desktop machine. One day it works fine. The next day it won't connect. Sometimes, even after he is connected, it stop works midstream. It also takes 10 minutes or so to boot up. The laptops always work without issue.
The two laptops would be issued IP addresses of 192.168.1.xxx but the desktop would be getting 12.83.xxxx.xx(something similar). The desktop's internet IP would receive its internet IP from the 2800 via DHCP just like the WRT54G is receiving its IP from the 2800. The two would essentially be on different LANs connected to the same router. Do you forsee any issues here?
Thanks!

CSCur03368 for IOS-XE: GNU Bourne Shell "Shellshock" lists affected product as 2800 series ISR

The content of CSCur03368 has a title of IOS-XE: GNU Bourne Shell "Shellshock" Vuln CVE-2014-6271/CVE-2014-7169. The only affected product listed is "Cisco 2800 Series Integrated Services Routers" with a known affected release of 15.2(3.2.39)E, and link to download software for the 2800.
Since 2800 series routers run IOS, not IOS-XE, someone needs to review and correct this info.

Cisco has updated the description since you posted this.

NetConfig issue wrt Cisco 3900 Series Router

Hi Cisco;
I can't able to configure my Cisco 3900 series Router via NetConfig tool. While I am able to Configure all other Routers (7600, & 2800) and Switchs (6500, 3700, 3560). I can accessable 3900 Series Router via Inventory Collection, Sync Archieve, Campus Manager, DFM and etc.
I have Cisco LMS 3.2 with RME 4.3 & using SNMPV3.
Thanks for your support.
Best regards;
Shoaib Ahmed

Hi Clarke;
Please find the requested Screen Shot.
Actully my problem is that, I can't configure my Cisco 3945 Routers (Shows not applicable devices) via NetConfig tool. I can use other tools like Sync archieve and etc is working fine for these 3945 routers.
Best regards;
Shoaib Ahmed

HP Color LaserJet 2800 series 2820

Question
Why is it, that the software delivered by HP them selve, isn't working as it should?
I've installed the DVD on 10.5 and I could scan, but not print.
After an uninstall of the DVD I could print, but not scan.
Now I've upgraded to 10.6.1. As I've read, several drivers are installed when needed. But as the Apple paged shows, no scan support for my printer.
Why doesn't HP make a print/scan driver so my expensive All-in-one printer could FINALY work as it should.
Is there a driver out there for Snow Leopard that does the trick of print/scan functionality?
Are there more people who are experiencing this problem?
Why does HP says it has OSX support for it's printer, if the driver AND installation software are of the minor quality?

Jonathan,
The Color LaserJet 2800 series is NOT support under Snow Leopard for anything other then print. You may try installing the 10.5 software to try and get things running again. It can be obtained [here|http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp? lang=en&cc=us&prodTypeId=18972&prodSeriesId=445194&prodNameId=445195&swEnvOID=21 9&swLang=8&mode=2&taskId=135&swItem=ly-58934-1], no guarantees it will work though.
Just trying to help.
Andrew

Cisco works LMS 3.0.1 cannot archieve configuration for cisco 3000 series vpn concentrator

Hi All,
Our problem is, we have Cisco Works LMS 3.0.1. cannot archieve configuration for cisco 3000 series vpn concentrator.
Any help would be greatly appreciated.
Thanks in advance.
Samir

Make sure you have filled out all of the HTTP/HTTPS credential data in DCR for these devices. RME will only use HTTPS to fetch VPN concentrator configurations.

I can't retrieve usm and vacm tables from router cisco 2800. Help please!!

Hi, I'm doing some tests in a router cisco 2800 using snmp in versions 2c and 3. I configured views and communities for version 2c and user, groups and views for version3; I suppose that the vacm and usm parameters involved in the groups, views are stored internally in usm, vacm tables. I wanted to check if the parameters I configured were inside the tables, but when I tried to retrieve all those values through get table or get next commands, I obtained the answer "end of mib view" in the application I'm using (SNMP J MANAGER) and also in wireshark where the requests are sent but the responses contain the OIDs belonging to the tables but with the value end of mib view.
I know for experience doing the tests, that "end of mib view" is obtained in a response when you try to request a OID that is outside of the view being used by a community. But the last thing I did was create a community related to a view with access to internet included. Later, I used that community (comlectura) in version 2c to retrieve those values of usmtable (1.3.6.1.6.3.15.1.2.2 ) and vacmtable (inside of 1.3.6.1.6.3.16.1) and nothing.
These are some commands I configured in the router:
snmp-server group readonly v3 auth read readview
snmp-server group writeonly v3 auth write writeview
snmp-server view readview internet included
snmp-server view writeview internet included
snmp-server view viewcomlectura mib-2 included
snmp-server view viewcomlectura2 system included
snmp-server community comlectura view readview RO
snmp-server community comlectura2 view viewcomlectura2 RO
snmp-server trap-source FastEthernet0/1
I think the cause of this error perhaps is because these tables don't exist in the CISCO MIB, but I don't thinks cisco devices ONLY have cisco mibs (
1.3.6.1.4.1.9) inside of them, because I can make request with OIDs of mib-2 branches. Anyway, please someone that can guide me in this problem. Thanks in advance.

You cannot use Mavericks. Ask a friend who still runs windows or any Mac OS except Mavericks to bring their laptop and help you out.
Or plug in a USB drive for instance and create a bootable version of any previous version of OSX since 10.5.x -10.8 all of which will work fine.
Or dual boot to windows where the latest airport utility is still 5.6

SNMP information from Cisco 2800 ISRs

I have several 2800 series routers setup as MGCP gateways with T1 PRI connections to the PSTN. Does anyone know what MIBs/OIDs to monitor for individual DS0 and DS1 activity? I opened a TAC case, but it wasn't very fruitful. Basically I just want to know how many active calls per PRI, averages, totals, uptime, etc.

Hi, the MIB would be is this:
ftp://ftp.cisco.com/pub/mibs/v2/ISDN-MIB.my
hope this helps, please rate post if it does!

Cisco 4003 series switch

Hi...All.
In cisco 4003 series switch i m getting error in post test its says , rtc failed, after that supervisorengineer wxx4012 LED status is Red.can any one tell me wt that means and hw to solve that problem.

plz fine the post test script...
003-B-Ground> (enable) 0:00.523556: Please set IPAddr variable
0:00.524147: Please set Netmask variable
0:00.524511: Please set Broadcast variable
0:00.525113: Please set TftpServer variable to do tftp downloads
0:00.525658: Network is not configured
WS-X4012 bootrom version 5.4(1), built on 2000.02.17 18:28:09
H/W Revisions: Meteor: 4 Comet: 8 Board: 2
Supervisor MAC addresses: 00:02:16:d2:5a:00 through 00:02:16:d2:5d:ff (1024 addr
esses)
Installed memory: 64 MB
Testing LEDs.... done!
The system will autoboot in 5 seconds.
Type control-C to prevent autobooting.
rommon 1 >
The system will now begin autobooting.
Autobooting image: "bootflash:cat4000.5-4-2.bin"
CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
CCCCCCCCCCCCCCCCCCCCCCCCCCC#############################
Starting Off-line Diagnostics
Mapping in TempFs
Board type is WS-X4012
DiagBootMode value is "post"
Telling ApkPageMan that we have 12288 pages of memory
Loading diagnostics...
Power-on-self-test for Module 1: WS-X4012
Status: (. = Pass, F = Fail)
processor: . cpu sdram: . rtc: F
eprom: . nvram: . flash: .
temperature sensor: . enet console port: . switch port 0: .
switch port 1: . switch port 2: . switch port 3: .
switch port 4: . switch port 5: . switch port 6: .
switch port 7: . switch port 8: . switch port 9: .
switch port 10: . switch port 11: . switch registers: .
switch sram: .
Module 1 Failed
Power-on-self-test for Module 2: not present
Port status: (. = Pass, F = Fail)
Module 2 Ignored
Power-on-self-test for Module 3: not present
Port status: (. = Pass, F = Fail)
Module 3 Ignored
Exiting Off-line Diagnostics
Failed Module Bringup Process
Use 'show test 1' to see results of tests.
Cisco Systems, Inc. Console

Deleting Cisco 2800/2900 Configuration

I have a Cisco 2800/2900 router that handles sensitive information for the DoD. If I do a "clear config all", will this delete the running config permanently or is there a way that someone can recover the config?

Hi,
When you issue the squeeze command, the router copies all valid files to the beginning of Flash memory and erases all files marked "deleted." At this point, you cannot recover deleted files, and you can now write to the reclaimed Flash memory space.
http://www.cisco.com/c/en/us/td/docs/ios/12_2/configfun/configuration/guide/ffun_c/fcf006.html#wp1001432
Permanently Deleting Files on a Flash Memory Device
When a Flash memory device is full, you may need to rearrange the files so that the space used by the deleted files can be reclaimed. To determine whether a Flash memory device is full, use the dir EXEC command.
To permanently delete files on a Flash memory device, use the following command in privileged EXEC mode:
Command
Purpose
Router# squeeze filesystem:
Permanently deletes all files marked "deleted" on a Flash memory device.
On Cisco 2600 and 3600 series routers,the entire flash file system needs to be erased once before the squeeze command can be used. After being erased once, the squeeze command should operate properly on the flash file system for the rest of the flash file system's history.
To erase an entire flash file system on a Cisco 2600 or 3600 series router, perform the following steps:
Command
Purpose
Router# no partition flash-filesystem:
Removes all partitions on the specified flash file system. Note The reason for removing partitions is to ensure that the entire flash file system is erased. The squeeze command can be used in a flash file system with partitions after the flash file system is erased once.
Router# erase filesystem:
Erases all of the file on the specified flash file system.
When you issue the squeeze command, the router copies all valid files to the beginning of Flash memory and erases all files marked "deleted." At this point, you cannot recover deleted files, and you can now write to the reclaimed Flash memory space.
HTH
Regards,
Akash

Creating VLAN on our Cisco 300 series router

I am wanting to create separate VLANs on our Cisco 300 series switches, but I am struggling to find any decent examples out there.
Our basic infrastructure is
Router with
192.168.1.1 VLAN1
192.168.2.1 VLAN2
The switch is set up on ports 2345 for VLAN2
Port 1 is attached to the router on VLAN1 and VLAN2 assigned.
My problems seem to be that I really not sure what settings I should be using for each the ports to get this to work correctly

Hi,
Hope below link will have the information which you are looking for.
https://supportforums.cisco.com/document/140341/vlan-configuration-articles-sx200300-series-managed-switches
If you are looking for only vlan creation then below link will help.
http://sbkb.cisco.com/CiscoSB/Loginr.aspx?login=1&pid=2&app=search&vw=1&articleid=80
According to your above description you have connected the router to port 1 of switch and you have configured it as vlan 1...Should this port be trunk???
Regards
Najaf

Cisco 2800 series vista problems

Similar Messages

Maybe you are looking for