3.75 W AC adapter Rating required (Supplied with Q10)

Could someone assist.
I have two a/c addaptors both applicable for BlackBerry, however the rating is not the same.
I need to know which one I must use with the Q10.
The ratings I have are as follows: [Both have the same input values of 100-240v - 50-60Hz 150mA]
Output: 5V===750mA
Output: 5V===850mA
Tx

Either one will work properly. I have the documentation that came with my Q10 (SQN100-3) and it lists 45 different BlackBerry chargers that are approved for use with the phone. The 850mA will charge it quicker but either one will get the job done.
Cheers.
- If my response has helped you, please click "Options" beside my post and mark it as solved. Clicking the "thumbs up" icon near the bottom of my response would also be appreciated.

Similar Messages

Is Excel Adapter is required to process Excel in Data services in Linux

Hi,
I am trying to read data from Excel and load it to HANA table. But i am not able to do it due to error. Do we require Excel Adapter to process Excel in Linux environment.
OS: SUSE Linux Enterprise server
DS version: DS 4.1 Sp2
Excel file name: TAL711.xls/xlsx
Error: Job Server <> defined for adapter datastore <TAL711> is not found in the repository. Select a valid Job Server in the Datastore
Regards,
Samatha

Hi Samatha Mallarapu,
Excel Adapter is required for Linux Platform .
Hope below link will help you out.
http://help.sap.com/businessobject/product_guides/sboDS41/en/sbo411_ds_designer_en.pdf#page=143&zoom=auto,0,614
Regards,
Akhileshkiran.

Is the power adapter rated 100-240v for the HP Stream 13 Laptop ?

Hi,
I want to buy it. and i want to be shore about the voltage...
.....Is the power adapter rated 100-240v for the HP Stream 13 Laptop ?
Thank You.

I might have tested it myself a few months ago, I cannot remember the results but I believe booting from the SD slot is not supported by the UEFI firmware. It is mentioned here in the comments of this Amazon review for the Stream 11: "I have not been able to boot ANYTHING from the micro-SDXC slot. I can install Ubuntu on it, but I cannot boot from it. I don't know if booting is even possible."

HT1665 I have a World Travel Adapter Kit for use with my iPad. can the plug adapters also be used on the Mac Pro charger to charge up my laptop when travelling or is a special converter needed.M

I have a World Travel Adapter Kit for use with my iPad when traveling abroad. I know this charger can be used on an iPhone, can the plug adapters also be used with the charger of a Mac Book Pro or is a special converter required?

Is there any concern about the type of travel adapter kit? For instance, some instructions indicate they are for heat creating appliances (hairdryers, curling irons, etc.). I bought such a set, but do they present any issues if used with more delicate electronic circuitry (for iPads, iPods, or with camera battery chargers). I am leaving for the UK on Monday and need to get it right - are they too strong for the Apple products if they are not to be used with computers? What other options are out there?

Installing Full Retail Win 8 Pro on a Lenovo System supplied with Win 8 Standard/Core

If you are attempting to install a full retail (or similar) copy of Win 8 Pro on Lenovo system that came with standard Win 8 (also referred to as Win 8 Core) installed from the factory, you will run into an issue at install time.
By MS design default , full Win 8 Pro retail (etc) versions look for a key embedded in the BIOS (often referred to as an OA3 or OA3.0 key). If that key does not match the version of Win 8 you are trying to install, the install will fail without offering the option of entering the retail key that was supplied with your full retail (etc) Win 8 Pro.
Microsoft has issued a "FAST PUBLISH" support article on how to work around this design approach. See
http://support.microsoft.com/kb/2796988
Note that this workaround requires the creating and placing of a PID.txt file by methods which are not entirely described in the support article, so be prepared to do some more digging for all the relevant information.
Cheers,
Bill
I don't work for Lenovo

Hi,
I have a Lenovo H520g essential desktop, which came with Windows 8 SL pre-installed. I bought my Lenovo on August 8 2013 and as of the November 2013 the machine was updated to Windows 8.1 Single Language.
Today, April 14th 2014, I bought Windows 8.1 Pro on a full retail DVD from a local physical Microsoft reseller. I have successfully installed Windows 8.1 Pro on my H520g. The installation run smooothly, no problems at all.
The steps I took were as follows:
1) Checked the UEFI BIOS to see if the DVD drive were included on the boot list and set it as the first boot device.
2) Booted the computer with the Windows 8.1 pro DVD on the optical drive.
3) Entered the Windows 8.1 License Key that came on the retail DVD.
4) Erased all partitions from the HDD were Windows 8.1 SL were installed.
5) Proceeded normally with the installation
Yesterday I made a phone call to the Microsoft support and they assured me that on all computers that come with Windows 8 SL pre-installed, it is possible to install Windows 8.1 Pro. The conditions are: 1) you must install the full retail version of Windows 8.1 Pro, not the OEM version; 2) you must do a clean install of Windows 8.1 Pro, not the install that preserves files and applications.
Cheers,
PauloBR

Supplier with multiple contacts to be assigned to single RFx document

Dear All,
The requirement is for a single RFx document, we need to assign one supplier with multiple contacts .System is not allowing to do so. Please let us know how to do this ie we should be able to assign one supplier with multiple contacts to a single RFx document.
Thanks in advance,
Sai.

Hi
Oracle Projects does not have any functionality regarding the ship to location.
You might want to analyze the reason to maintain two different locations of the same customer on the same project. Do you need to assign the different locations to top tasks,? If If it is important you may use a DFF on the task level for the ship to location.
Dina

I require help with my first website

As you can see from many of my recent posts, I am new to web development, and I have decided that I am going to need some help.
This forum has been a huge help, and I will continue using it, but the reality of the situation is that progress is slow as I am learning as I go, each junction I reach and require help with is holding up progress, which wouldn't be a problem if I had more spare time, but I simply don't.
Is anybody willing to help me? It would be paid work so I would need to discuss how this would work with rates etc... here are some details:
The domain is already setup, and you can see the first page I have been working on here: http://www.elliotnewman.com/index/test7.html
The closet website I can find for your reference is: http://www.jaspaljandu.com/home/
My site will initially not be quite as established as Jaspal's, but in essence the functionality will be similar. The things I know of that I will need help on are:
Setting up the ordering and payment process when a customer wants to order a print, including automated email notifications, and check out forms ( this may also require membership fields or maybe through paypal)
Setting up the interactive framing graphics - ref - http://www.markgray.com.au/gallery/limited-edition-prints/forgotten-island.php
Potentially helping to setup a blog
Work with me on integration - and updates (ie build the all the templates needed so updates and new images can be posted by myself easily)
Automation of the counts of the limited editions
Setting up links to Facebook, twitter, linkedin etc
Reviewing and testing any code that I create
Along with these points I will also need standby help with the code I am directly working on, so file sharing may have to be setup. It is also worth noting that I will supply all the graphics and the design elements for every page, I will also be very specific with briefs as I know exactly what I want to achieve.
If anybody is interested please send me a private message, I would need to see some examples of your experience, details on your availability and your rate - whether thats per day, per hour and a rough estimate on how long you think the work will take.
Also, if anybody knows somebody outside this forum that you think could help me then please also forward this on.
Apologies if this is not the best place to post this.
Elliot.

Hi
In addition to Nancy s comments, reading the following line -
Along with these points I will also need standby help with the code I am
directly working on, so file sharing may have to be setup.
What you are basically after is a tutor, to guide you in what you are doing. In this respect it may be worth your while to read-up on designing web pages,as after a quick glance of the code, (from your previous post regarding the background image ) the main problem you are having is that you are not 'implementing' a consistent design/development procedure.
Try reading the following -
General tutorials on html, css, etc - http://www.w3schools.com/.
Design of web site, general - http://articles.sitepoint.com/article/principles-beautiful-web-design.
PZ
www.pziecina.com

Which wattage adapter should I use with the composite cable with my iPad?

Which wattage adapter should I use with the composite cable when connected to my iPad while watching T. V. .

Ultimately, use the power adapter that came with the iPad. But you should use any USB based power adapter that has a 10 watt/ 2 amp or higher power rating. Look close when buying a thrid party adapter, if it does not specify 10 watts/2 amps it is a lower 5 watt/1 amp charger that will not work.

Is this power adapter (12W) really compatible with iPod shuffle?

Hello,
I'm just wondering if the 12W power adapter is really compatible with the iPod shuffle 4th generation.
(http://store.apple.com/us/product/MD836LL/A/apple-12w-usb-power-adapter?fnode=74)
It says it is compatible, but it doesn't make sense to me. Because iPod shuffle is so tiny, I fear that it would burn out if I plug it into a 12W. I understand that the 5W version is compatible but 12W seems interesting.
What do you think? Do you use 12W for the iPod shuffle, too?

It works fine and will not damage the Shuffle. The Shuffle will draw only the power it requires.

Getting error while creating a new web app saying "The password supplied with the username domainname\username was not correct. Verify that it was entered correctly and try again"

Hi ,
I am trying to create a new web app using Central Administration in Sharepoint 2010 and getting an error "The password supplied with the username was not correct. Verify that it was entered correctly and try again".
I tried running this command also "stsadm -o updatefarmcredentials -userlogin <domain\username> -password <newpassword>" but when it got executed it showed me "Access Denied".
What should i do ??
Thanks in advance.
Regards, Anurag

HI,
right click on command icon and click run as administrator then use above stsadm commend to update credential. If still you face same issue then try with powershell as mention in below link: (make sure that you open sharepoint powershell as run as administrator)
http://smartrider.wordpress.com/2010/07/15/powershell-script-to-create-web-application-and-site-collection-in-sharepoint-2010/
let us know your result
Hemendra: "Yesterday is just a memory,Tomorrow we may never see"
Whenever you see a reply and if you think is helpful, click "Vote As Helpful"! And whenever
you see a reply being an answer to the question of the thread, click "Mark As Answer

Mini DVI to DVI doesn't fit DVI to ADC connector supplied with my machine

The DVI end of the ADC adapter has small pins above and below the blade side of the plug while the DVI end of the mini-DVI to DVI adapter has no openings to accept them. Both of these items were shipped to me by Apple with my 12" PB. Any suggestions?
I suspect someone must have encountered this but I didn't see it anywhere when I did a search.

My apologies. I confused an adapter from another company with an Apple product.

Why my new Mac mini DVI dual link mini display port adapter doesn't work with my 30"display (LG W3000H)?

Hello There
Can any of you advise on the below? Tried to connect Mac mini with a 30" display through a DVI dual link mini display port adapter. For the first try Mac mini go connected to the display, then i've chosen the highest resolution (2560x1600, native) and right at that moment they got disconected. Since then the display stays black. What can be the issue, is it possible DVI dual link mini display port adapter is not compatible with 30"display (LG W3000H)? It works with DVI male-male cable plus DVI HDMI adapter as long as the resolution stays under 1280x800. Any idea is much appreciated.
Thank you, Vera

Hi,
I can report that my Mac Mini Intel Duo connected instantly and without even having to set it up (on the first try) with my 1366x768 native resolution DELL 50" Plasma Display. It's so beautiful that I just want to stand there and fondle my HDTV as I drool haplessly like Homer Simpson with a doughnut in his mouth. Seriously, no problems.... guess I bought the right cable (ebay).
Before you buy a Duo, make sure you're aware of the airport and bluetooth issues that so many (maybe everyone who tries to use them together) are having. It seems that bluetooth interferes with airport, or maybe the other way around. Anyway, it's messed up. Also, Airport reception is generally VERY poor with the new Intel Mac Mini.
Despite these things, I still love mine (I now have 2 base stations and an airport express for my powerhouse wireless needs, and an external DLink bluetooth-2-USB dongle solved the bluetooth/airport issues... in my case).
FWIW,
awk
667-MHz Ti PowerBook G4. Mac OS X (10.3.9)

Sharepoint server issue:: Register Managed Account -Password supplied with username was not correct

when i am creating a managed account from share point server admin it is showing:-
The password supplied with the username fimservice was not correct. Verify that it was entered correctly and try again.
i have put correct password but even though it is showing this error.
i have even tried to enter username with my domain name like indialab1\fimservice but this account is not being
recongnized.
Thanks for your help

Additionally you can follow / refer steps mentioned in
http://blogs.technet.com/b/seanearp/archive/2011/01/25/updating-passwords-on-sharepoint-2010.aspx
Let us know your results
Regards,
Pratik Vyas | SharePoint Consultant |
http://sharepointpratik.blogspot.com
Posting is provided AS IS with no warranties, and confers no rights
Please remember to click Mark As Answer if a post solves your problem or
Vote As Helpful if it was useful.

The document could not be saved. The server said: "The operation failed because an unexpected error occurred. (Result code 0×80020005)" Please ensure you have completed all required properties with the correct information and try again.

I am having problems saving documents back to SharePoint when any of the document properties (metadata columns) are set to be "managed metadata". The check-in/save fails with error:
The document could not be saved. The server said:
“The operation failed because an unexpected error occurred. (Result code 0×80020005)”
Please ensure you have completed all required properties with the correct information and try again.
I have seen similar threads that suggest this is a known issue with this version of Acrobat but I would like conformation from Adobe that this is a known issue and whether it is fixed in a newer version?
Adobe Acrobat version 10.1.13
SharePoint 2010

Hi quodd,,
We are sorry for the issue being faced by you. I need some information from you so that I take further steps:
1. Which Adobe product are you using Acrobat or Adobe reader- what is the complete version?
2. How are you opening and saving the PDF, the exact workflow?
Are you doing it from within Adobe Reader/Acrobat application or opening it from browser, doing changes and saving it using browser itself.
3. Can you try to save a PDF to library with Custom template and managed metadata columns using browser directly.
4. Please verify that columns name do not contain spaces or some other special characters.
Can you try to save PDF to library with Custom template and just a single managed metadata column with a simple name
Thanks,
Nikhil Gupta

An issue using the COM components supplied with SAP GUI 6.2 or 6.4

We are having an issue using the COM components supplied with SAP GUI 6.2 or 6.4. We used to have SAP 4.6c and now we have 5.0. When we were on 4.6c, we used these COM components to logon and execute RFC calls and we had much success. Now that we are on 5.0, we cant seem to instance any SAP functions that have something to do with SAP Workflow. We have experienced this problem when using VB6 or .NET, but our existing code that always worked is in VB 6.0.
SAP Components used:
o     SAP Logon Control
o     SAP Function Control
o     Librfc32.dll
o     Other supporting C DLLs and/or COM object supplied with the SAP GUI installation.
For example, if we want to call the RFC ARCHIV_CONNECTION_INSERT, this code fails in VB6 when the Set objworkflow = objFuncCtrl.Add(strFunction) line of code executes. Instead of returning an instance of the object ARCHIV_CONNECTION_INSERT function, no object is created. In 6.2, SAP raises no errors, but the object we are trying to create is still Nothing. If we use 6.4, SAP raises an error SAP data type not supported via a message box and then the object is still = Nothing. Interestingly enough, the 6.2 GUI COM controls dont display the error dialog. The message box that is shown comes from the SAP Function COM Object "SAP.Functions" (wdtfuncs.ocx).
Now, what is interesting is if we use the same code to call a standard function or custom function that doesnt have anything to do with SAP Workflow, then the code works fine. Again, all of our code used to work just fine on an SAP 4.6 system.
Here is the code that fails:
    'SAP Logon control - object for creating connections to an SAP system
    Dim objSAPLogonCtrl As Object
    'SAP connection object
    Dim objConnection As Object
    'Object that will represent the SAP function called
    Dim objSAP As Object
    'SAP function control object - object factory for creating other SAP function objects
    Dim objFuncCtrl As Object
    'Create instance of an SAP logon conrol
    Set objSAPLogonCtrl = CreateObject("SAP.Logoncontrol.1")
    'Create a connection object
    Set objConnection = objSAPLogonCtrl.NewConnection
    'Define connecion parameters
    objConnection.ApplicationServer = "sapvm"
    objConnection.SystemNumber = "00"
    objConnection.Client = "800"
    objConnection.User = "iissap"
    objConnection.Password = "tstadm"
    objConnection.Language = "E"
    objConnection.TraceLevel = 10
    'call the logon method of the connection object
    If objConnection.Logon(0, True) = False Then
        MsgBox Error
        Exit Sub
    End If
    'Create an instance of the SAP Function control object
    Set objFuncCtrl = CreateObject("SAP.Functions")
    'Set the function control connection object
    Set objFuncCtrl.Connection = objConnection
    'Function name to be generated and called
    Dim strFunction As String
    strFunction = <b>"ARCHIV_PROCESS_RFCINPUT"</b>
    'Create an instance of the function defined in strFunction
    Set objworkflow = objFuncCtrl.Add(strFunction)
    If objworkflow Is Nothing Then
        MsgBox "Could not create object " & strFunction
    Else
        MsgBox strFunction & " object created."
    End If
If anyone has seen anything like this or has any ideas, please help!
Mike and Hameed
<b></b>

Hi,
documentation on the Scripting API is available at ftp://ftp.sap.com/pub/sapgui/win/640/scripting/docs/
This API is a replacement of the existing, obsolete COM interfaces.
Best regards,
Christian

3.75 W AC adapter Rating required (Supplied with Q10)

Similar Messages

Maybe you are looking for