3310 configuration, please give me some help.
Hi all, I'm having some trouble making a specific configuration for the storedge 3310, I'm making a script using sccli utility, for my configuration I have to remove all the configuration that storedge comes with by default, but I must do so using sccli. When I remove both host luns I can't acess the storedge device, I already posted this question to portuguese assistant of sun, but it has been more then 3 weeks without a reply.
So tryed using another method, I first remove all the spares that come with the raid 5 default configuration, and I then remove one off the host luns, atfer that I remove the logical drive that was in it, and I was going to do the new configuration, but I stoped on the folowing problem, how can I create a raid0 drive on channel2 using all six disks and then create another raid0 using the remaining 6 disks on channel0, and after that make a mirror of one in to the other?
For the configuration of the raid0 it's easy but the to raid1+0 is what's troubling me:
echo "create logical-drive raid0 2.0-5 primary"|sccli -o -w 10.1.0.100
after that I would create a new lun map using the map command, and then remove all the configuration on channel0 and then create the new configuration
echo "create logical-drive raid0 0.0-5 primary"|sccli -o -w 10.1.0.100
my question is how can I now mirror one to the other?
I really would like to know, I've been thinking about this for some time, but I still haven't found a solution, if someone could please point me what I'm doing wrong, I would really apreciate-it.
Orlando
P.S. Sorry for my bad english
I would like to thank everybody that has even think about my question, I found part of the answer (or so I think I did) in the Best Practise Guide:
http://docs.sun.com/source/816-7293-12/bestpractices.html
"Assign two drives as global spares, four drives to the RAID 1 logical drive (it automatically becomes RAID 0+1) and the remaining drives to the RAID 5 logical drive. Scale storage capacity by adding disks to the RAID 5 logical drive."
So I can assume that if I do the following configuration:
echo "create logical-drive raid1 0.0-5,2.0-5 primary"|sccli -o -w 10.1.0.100 this would create a huge Raid1 logical-drive that would do raid (1+0) it would do stripping among all the drives, although this might be highly expensive this would carry an throughput advantage (writting/reads) my problem is how can I do this from a command line, if I in order to operate the storedge using the sccli I need to have a lun active, but if I clear all the luns, then I can't acess the device, but in order to delete the default settings and delete the logical drives that come preconfigured I need to delete the host lun first, you probably can see my dilema now, one big loop :(
any help, or sugestion will be appreciated
Thanks in advance
Orlando Reis
Similar Messages
-
I'm using version 10.7.5 OSX. I can't play or use the normal AVI recently. Some problem with (codecs version incompatible with OSX) Please give me some help. I'm in Vietnam and to have a real place to have stuffs from Apple is ****…
I would recommend that you download and install the excellent and Free "VLCPlayer for Mac", which reads many more types of files for video than Quicktime Player:
http://vlc-media-player.en.softonic.com/mac -
HP Please give us some help with the Firebird!!
HP,
PLEASE give some info on the Firebird.
There has been no updated drivers for this machine in nearly 2 years!
Why can't I get an official driver update?EvilHenchman wrote:
HP,
PLEASE give some info on the Firebird.
There has been no updated drivers for this machine in nearly 2 years!
Why can't I get an official driver update?
It would certainly help if you would identify your FireBird with its product name/number.
Best regards,
erico
****Please click on Accept As Solution if a suggestion solves your problem. That will help another person facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer -
SOMEONE please give me some HELP
I am EXtREMELY Frustrated right now. I have a HP 6515 that DOES NOT PRINT BLACK INK...I see where things are posted regarding this problem numerous times here. HOWEVER, there is no SOLUTION made public. Everythings is going to PRIVATE MESSAGE. What is the secret.....? Would it be.....YOU NEED TO GET A NEW PRINTER??????...If so, this is the bigest bunch of crap. I have had this printer for about 2.5 years, no reason for it to take a crap. Only used HP ink.....SOMEONE PLEASE HELP ME.....Just bout $120 worth of ink for it......thats more than ya pay for the printer....come on....
Hello lisbell563,
Thank for the reply. Are you using Windows-based computers or Mac OS?
If you are on windows OS, I would like to suggest you to download and try "HP Print and Scan Doctor" which can help to assist you with troubleshooting and problem solving to resolve many common problems experienced with HP print and scan products connected to Windows-based computers.
If you are on Mac OS, you may not able to use HP Print and Scan Doctor. However, since one of the error you are facing is "fails to align" and I would like to refer you to this "Alignment Failed" web page for further troubleshooting.
-Bryan-
*I am an HP employee*
** Please click "Accept as Solution" if it solved your problem, so others can find it **
***Give Kudos to say "Thanks" by clicking on the thumbs up button under my name*** -
WEB SMS receiving problem. Please, give me some help.
Hi, i´m having a problem with web sms receiving. I receive sms from another cellphones but i cant receive the web sms. Is there a fix for this?
I have a lot of services that send me web sms, like internet banking and others, so i cant use my services because my iphone cant receive this sms from web.The code is too complex, so I can put all code at here. sorry.
The logic is:
a frame has a JDialog object,and show the JDialog object if need,all controls were added to the JDialog in the function jbInit() when the JDialog object was created.
The point that I want to know is what reasons may cause the problem.
thank so very much.
masstensor
//--------------->> some code fragment
class MyDialog extens JDialog {
JPanel myPanel = new JPanel();
JButton myButton = new JButton();
public MyDialog() {
super(frame, title, false);
try {
jbInit();
pack();
catch(Exception ex) {
ex.printStackTrace();
void jbInit() throws Exception {
myPanel.setLayout(null);
getContentPane().add(myPanel);
myPanel.add(myButton, null);
} -
Urgent!!! please give me some advice
i quite new in J2ME programming. i encountered a problem that my MIDlet cannot pass parameter to servlet. i had tried to not using os.flush(), but it's still not working. please give me some suggestion!
MIDlet
* Login.java
import javax.microedition.midlet.*;
import javax.microedition.lcdui.*;
import javax.microedition.io.Connector;
import javax.microedition.io.HttpConnection;
import javax.microedition.io.StreamConnection;
import java.io.DataOutputStream;
import java.io.DataInputStream;
import java.io.InputStream;
import java.io.OutputStream;
import java.io.IOException;
import java.util.*;
public class Login extends MIDlet implements CommandListener {
Display display;
boolean commandAvailable;
// String idPassword;
CommandThread commandThread;
Form inputForm;
Form outputForm;
TextField userid;
TextField password;
StringItem response;
Command cmdExit;
Command cmdOK;
public void startApp() {
display = Display.getDisplay(this);
inputForm = new Form("Authorization");
userid = new TextField("User",null,25, TextField.ANY);
inputForm.append(userid);
password = new TextField("Password",null, 15, TextField.PASSWORD);
inputForm.append(password);
cmdOK = new Command("OK",Command.SCREEN,1);
cmdExit = new Command("Exit",Command.EXIT,1);
inputForm.addCommand(cmdOK);
inputForm.addCommand(cmdExit);
inputForm.setCommandListener(this);
outputForm = new Form("Student Option");
response = new StringItem(null,null);
outputForm.append(response);
outputForm.addCommand(cmdExit);
outputForm.setCommandListener(this);
commandAvailable = false;
commandThread = new CommandThread(this);
commandThread.start();
display.setCurrent(inputForm);
public void pauseApp() {
public void destroyApp(boolean unconditional) {
public void commandAction(Command cmd, Displayable d) {
if (cmd == cmdExit) {
destroyApp(false);
notifyDestroyed();
else if (cmd == cmdOK)
synchronized (this) {
commandAvailable = true;
notify();
class CommandThread extends Thread {
MIDlet parent;
boolean exit = false;
public CommandThread(MIDlet parent) {
this.parent = parent;
public void run() {
while (true) {
synchronized(parent) {
while(!commandAvailable) {
try {
parent.wait();
catch (InterruptedException e) {
commandAvailable = false;
performLogin();
public void performLogin() {
HttpConnection conn = null;
InputStream is = null;
OutputStream os = null;
byte[] receivedData = null;
try {
String url = getAppProperty("Login.URL");
conn = (HttpConnection)Connector.open(url);
byte[] postData = createPostData();
conn.setRequestMethod(HttpConnection.POST);
conn.setRequestProperty("User-Agent", "Profile/MIDP-1.0 Configuration/CLDC-1.0");
conn.setRequestProperty("Content-Type","application/x-www-form-urlencoded");
conn.setRequestProperty ( "Content-Length", Integer.toString (postData.length));
// conn.setRequestProperty("Accept", "application/octet-stream" );
conn.setRequestProperty("Connection", "close" );
// byte[] postData = createPostData();
System.out.println("postData="+postData);
conn.setRequestProperty("Content-length",Integer.toString(postData.length));
os = conn.openOutputStream();
os.write(postData);
for (int i=0;i<postData.length;i++)
os.write(postData);
// os.flush();
os.close();
is = conn.openInputStream();
String contentType = conn.getType();
int len = (int)conn.getLength();
if (len > 0) {
receivedData = new byte[len];
int nb = is.read(receivedData);
else {
receivedData = new byte[1024];
int ch;
len = 0;
while ((ch = is.read()) != -1) {
receivedData[len++] = (byte)ch;
response.setText(new String(receivedData,0,len));
display.setCurrent(outputForm);
catch (IOException e) {
System.out.println(e.getMessage());
e.printStackTrace();
finally {
try {
if (is != null) {
is.close();
if (os != null) {
os.close();
if (conn != null) {
conn.close();
catch (IOException e) {
public byte[] createPostData() {
StringBuffer sb = new StringBuffer();
sb.append("userid=");
sb.append(userid.getString());
sb.append("&password=");
sb.append(password.getString());
System.out.println("sb = <" + sb.toString() + ">");
return sb.toString().getBytes();
servlet
import java.io.*;
import java.text.*;
import java.util.*;
import javax.servlet.*;
import javax.servlet.http.*;
import java.sql.*;
public class LoginServlet extends HttpServlet {
static final String dbURL = "jdbc:mysql://localhost/projectdb?" + "user=wongyuenmei&password=wongyuenmei";
public void doPost(HttpServletRequest request,HttpServletResponse response) throws IOException, ServletException {
Connection conn = null;
String nextJSP = null;
try {
Class.forName("org.gjt.mm.mysql.Driver");
catch (ClassNotFoundException e) {
throw new ServletException("Unable to load JDBC driver");
try {
String id = request.getParameter("userid").trim();
String pass = request.getParameter("password").trim();
if (id==null)
String tempid=id;
String temppass=pass;
conn = DriverManager.getConnection(dbURL);
Statement stmt = conn.createStatement();
String query = "SELECT cno, idno " + "FROM student " + "WHERE idno = '" + id + "'AND password ='" + pass + "'";
ResultSet rs = stmt.executeQuery(query);
if (rs.next()) {
StringBuffer fullName = new StringBuffer();
fullName.append(rs.getString(1));
fullName.append(" ");
fullName.append(rs.getString(2));
request.setAttribute ("fullName", fullName.toString());
nextJSP = "/LoginOK.jsp";
else {
StringBuffer temptest = new StringBuffer();
temptest.append(tempid);
temptest.append(&temppass);
request.setAttribute("temptest", temptest.toString());
nextJSP = "/LoginFailed.jsp";
conn.close();
ServletConfig config = getServletConfig();
ServletContext context = config.getServletContext();
RequestDispatcher rd = context.getRequestDispatcher(nextJSP);
rd.forward(request, response);
catch (SQLException e) {
throw new ServletException("SQL call failed");
catch (Exception e) {
throw new ServletException(e.getMessage());
finally {
if (conn != null) {
try {
conn.close();
catch (SQLException e) {
throw new ServletException("connection close failed");
public void doGet(HttpServletRequest request, HttpServletResponse response) throws IOException, ServletException {
doPost(request, response);
ur help is very appreciated!Still the same problem. All the parameter get by server are null.
Using GET, and add parameter to url, everything is fine.
encodedPostData = "E2EE_PAM_ID"+"="+E2EE_PAM_ID+"&"+"E2EE_USER_ID"+"=" E2EE_USER_ID"&"+"E2EE_USER_SEGUID"+"="+E2EE_USER_SEGUID+"&"+"E2EE_RPIN"+"="+E2EE_RPIN
+"&LoginBtn=Login";
c = (HttpConnection)Connector.open(request);
c.setRequestMethod(HttpConnection.POST);
c.setRequestProperty("User-Agent","Profile/MIDP-1.0 Configuration/CLDC-1.0");
c.setRequestProperty("Content-Type:","application/x-www-form-urlencoded");
os = c.openOutputStream();
os.write(encodedPostData.getBytes());
//os.flush();
System.out.println(encodedPostData);
rc = c.getResponseCode();
if (rc != HttpConnection.HTTP_OK) {
throw new IOException("HTTP response code: " + rc);
is = c.openInputStream();
.......... -
Regarding how to use index , please give me some example if possible
Hello everybody:
Thank you all for your help in advance .
would you please tell me how to use index, please give me some example if possible. couldn't thank you more!
best regards .
FrankIndex is used for faster access of data base tables.
An index helps to speed up selection from the database. An index is a sorted copy of selected database table fields.
The primary index is always automatically created in an ABAP-based SAP system. It consists of the primary key fields of the database table. This means, for each combination of the index fields exists a maximum of one record in the table. This kind of index is called a UNIQUE index.
If the primary index cannot be used to determine selection result, (for example, the WHERE condition does not contain any primary index fields), the system searches the whole table. To prevent this, and determine the selection result by searching through a restricted number of database records, you can create a secondary index.
However, you should not define an index for all possible fields in the WHERE condition.
Check this thread..u have more details.
In which situation we can use the reading of index -
Ipjone6, silver, 64GB
I lost my password and i could get into my phone, i tried but it said connect to itune. i did, but i did not get any result. please give me some advises how do i get my password back or reset with a new one?how to reset password:
https://iforgot.apple.com/password/verify/appleid -
I'm trying to downgrade my storage on my ipod but when I chose my new storage i'm not able to complete the choice because the 'done' button doesn't do anything. can someone please give me some advice?
Are you choosing a different plan before tapping Done?
To downgrade, you should be doing the following:
Go to Settings > iCloud > Storage & Backup.
Tap Change Storage Plan.
Tap Downgrade Options and enter your Apple ID password.
Choose a different plan to use when your current storage plan expires.
Tap Done. -
Received apple tv as gift, my tv/home theater situation has no HDMI input capabilities. My only option is an optical connection, please give me some inexpensive optical cable suggestions???
Welcome to the Apple Community.
HDMI is required to connect the Apple TV to a TV or through a receiver. The optical connection is for audio only. -
I have a related but different problem... I prefer that the photos/events on my iPhone and iPad be in "date created" order. Does anyone know if this is possible? Apple...please give us some options!!!
This response is a little late as I just read about your problem. I have a 2012 Dodge Charger and a 2012 Chrysler Town and Country and both worked flawlessly with the iPhone 5s my wife and I had. However, we just upgraded to the iPhone 6 and Uconnect will receive calls but you cannot answer them. You can callout successfully, however. the annoyance being the inability to answer incoming calls in the HandsFree mode.
-
Please give me some sample program releated BOM
please give me some sample program releated BOM
Hi,
*& Module : PP |
*& Application : The program loads the Bill of Material |
*& |
*| Modification Log |
*| -
|
*| Programmer |
*| Change |
*| -
|
REPORT zpp0120 NO STANDARD PAGE HEADING
MESSAGE-ID z0
LINE-SIZE 132
LINE-COUNT 65(2).
Internal Tables *
*Internal table for the BOM file.
DATA: BEGIN OF i_bom OCCURS 0,
matnr(18),
werks(4),
stlan(1),
stlal(2),
stktx(40),
bmeng(16),
menge(16),
posnr(4),
postp(1),
meins(3),
datuv(10),
fmeng(1),
idnrk(18),
potx1(40),
ausch(7),
END OF i_bom.
Extracting Document and Doc type for POSTP = D.
DATA : BEGIN OF i_stpo OCCURS 1,
doknr(25),
dokar(3),
posnr(4),
stlnr LIKE mast-stlnr,
END OF i_stpo.
Local work area
DATA: g_my_rec_in LIKE i_bom.
Declare internal table for Call Transaction and BDC Session
DATA: i_bdc_table LIKE bdcdata OCCURS 0 WITH HEADER LINE.
Global Variables *
DATA: g_counter(2) TYPE n,
g_field_name(18) TYPE c,
zc_yes TYPE syftype VALUE 'X'.
Selection Screen *
SELECTION-SCREEN BEGIN OF BLOCK a WITH FRAME TITLE text-001.
PARAMETERS: p_fname1 TYPE localfile .
SELECTION-SCREEN SKIP 1.
SELECTION-SCREEN BEGIN OF BLOCK b WITH FRAME TITLE text-002.
PARAMETERS: p_rloc1 AS CHECKBOX DEFAULT 'X'.
SELECTION-SCREEN BEGIN OF BLOCK c WITH FRAME TITLE text-005.
PARAMETERS p_group(12) OBLIGATORY DEFAULT 'ZBOM'.
SELECTION-SCREEN END OF BLOCK c.
SELECTION-SCREEN END OF BLOCK b.
SELECTION-SCREEN END OF BLOCK a.
**WRITE the report header
TOP-OF-PAGE.
INCLUDE zheading.
Start of selection *
START-OF-SELECTION.
Load Input file
PERFORM f_load_input_file.
Create BDC records.
PERFORM create_bdc_records .
*& Form Create_BDC_records
text:* perform the BDC for the records in the internal table
--> p1 text
<-- p2 text
FORM create_bdc_records .
DATA: v_stlnr LIKE mast-stlnr.
DATA: v_postp(1) VALUE 'D'.
IF NOT i_bom[] IS INITIAL.
Open BDC session
PERFORM open_bdc_session.
SORT i_bom BY matnr werks posnr.
SELECT SINGLE stlnr INTO v_stlnr
FROM mast
WHERE matnr = i_bom-matnr
AND werks = i_bom-werks.
SELECT doknr dokar posnr stlnr
INTO TABLE i_stpo
FROM stpo
FOR ALL ENTRIES IN i_bom
WHERE postp = v_postp
AND posnr = i_bom-posnr
AND stlnr = v_stlnr.
SORT i_stpo BY posnr stlnr.
LOOP AT i_bom.
g_my_rec_in = i_bom.
READ TABLE i_stpo WITH KEY posnr = i_bom-posnr
stlnr = v_stlnr
BINARY SEARCH.
AT NEW matnr.
CLEAR i_bdc_table[].
PERFORM insert_screen_header.
ENDAT.
Setting up counter for 20 line items
IF g_counter = 20.
g_counter = 1.
ENDIF.
PERFORM bdc_field USING 'BDC_OKCODE'
'/00'.
*next screen
PERFORM bdc_dynpro USING 'SAPLCSDI' '0140'.
PERFORM bdc_field USING 'BDC_CURSOR' 'RC29P-FMENG(01)'.
PERFORM bdc_field USING 'BDC_OKCODE' '/00'.
CONCATENATE 'RC29P-POSNR(' g_counter ')' INTO g_field_name.
PERFORM bdc_field USING g_field_name i_bom-posnr.
CONCATENATE 'RC29P-IDNRK(' g_counter ')' INTO g_field_name.
PERFORM bdc_field USING g_field_name i_bom-idnrk.
CONCATENATE 'RC29P-MENGE(' g_counter ')' INTO g_field_name.
PERFORM bdc_field USING g_field_name i_bom-menge.
CONCATENATE 'RC29P-MEINS(' g_counter ')' INTO g_field_name.
PERFORM bdc_field USING g_field_name i_bom-meins.
CONCATENATE 'RC29P-POSTP(' g_counter ')' INTO g_field_name.
PERFORM bdc_field USING g_field_name i_bom-postp.
CONCATENATE 'RC29P-FMENG(' g_counter ')' INTO g_field_name.
PERFORM bdc_field USING g_field_name i_bom-fmeng.
*next screen
PERFORM bdc_dynpro USING 'SAPLCSDI' '0130'.
PERFORM bdc_field USING 'BDC_OKCODE' '/00'.
Check the Item category to direct the screen flow accordingly.
CASE i_bom-postp.
WHEN 'B'.
PERFORM item_text_insert.
WHEN 'Z'.
PERFORM item_text_insert.
WHEN 'T'.
PERFORM item_text_insert.
WHEN 'N'.
PERFORM bdc_field USING 'BDC_CURSOR' 'RC29P-AUSCH'.
PERFORM bdc_field USING 'RC29P-AUSCH' i_bom-ausch.
next screen
PERFORM item_text_insert.
*next screen
PERFORM bdc_dynpro USING 'SAPLCSDI' '0133'.
PERFORM bdc_field USING 'BDC_OKCODE' '/00'.
PERFORM bdc_field USING 'RC29P-EKORG' ' '.
WHEN 'D'.
PERFORM bdc_field USING 'RC29P-DOKNR' i_stpo-doknr.
PERFORM bdc_field USING 'RC29P-DOKAR' i_stpo-dokar.
next screen
PERFORM item_text_insert.
When POSTP = X, L.
WHEN OTHERS.
PERFORM bdc_field USING 'BDC_CURSOR' 'RC29P-AUSCH'.
PERFORM bdc_field USING 'RC29P-AUSCH' i_bom-ausch.
next screen
PERFORM item_text_insert.
ENDCASE.
g_counter = g_counter + 1.
next screen
PERFORM bdc_dynpro USING 'SAPLCSDI' '0140'.
PERFORM bdc_field USING 'BDC_CURSOR' 'RC29P-POSNR(01)'.
PERFORM bdc_field USING 'BDC_OKCODE' '=FCBU'.
AT END OF matnr.
PERFORM insert_bdc_new.
ENDAT.
ENDLOOP.
CLEAR i_bom[].
PERFORM close_bdc_session.
Release the BDC sessions created
PERFORM release_bdc.
ENDIF.
ENDFORM. " open_group
*& Form bdc_dynpro_start
Initialize the screen
-->P_G_PROGRAM_1
-->P_G_SCREEN
FORM bdc_dynpro USING p_g_program_1
p_g_screen.
CLEAR i_bdc_table.
i_bdc_table-program = p_g_program_1.
i_bdc_table-dynpro = p_g_screen.
i_bdc_table-dynbegin = 'X'.
APPEND i_bdc_table.
ENDFORM. " bdc_dynpro_start
*& Form bdc_field
Insert field *
FORM bdc_field USING f_name f_value.
CLEAR i_bdc_table.
i_bdc_table-fnam = f_name.
i_bdc_table-fval = f_value.
APPEND i_bdc_table.
ENDFORM. "bdc_insert_field
*& Form open_bdc_session
Open the BDC session
FORM open_bdc_session .
Open BDC session and creat and update condition records
CALL FUNCTION 'BDC_OPEN_GROUP'
EXPORTING
client = sy-mandt
DEST = FILLER8
group = p_group
HOLDDATE = FILLER8
keep = 'X'
user = sy-uname
RECORD = FILLER1
PROG = SY-CPROG
IMPORTING
QID =
EXCEPTIONS
client_invalid = 1
destination_invalid = 2
group_invalid = 3
group_is_locked = 4
holddate_invalid = 5
internal_error = 6
queue_error = 7
running = 8
system_lock_error = 9
user_invalid = 10
OTHERS = 11
IF sy-subrc <> 0.
MESSAGE ID sy-msgid TYPE sy-msgty NUMBER sy-msgno
WITH sy-msgv1 sy-msgv2 sy-msgv3 sy-msgv4.
ENDIF.
ENDFORM. " create_bdc_session
*& Form insert_screen_header
Insert the Header data into the screens
FORM insert_screen_header .
g_counter = 1.
PERFORM bdc_dynpro USING 'SAPLCSDI' '0100'.
PERFORM bdc_field USING 'BDC_CURSOR' 'RC29N-STLAL'.
PERFORM bdc_field USING 'BDC_OKCODE' '/00'.
PERFORM bdc_field USING 'RC29N-MATNR' g_my_rec_in-matnr.
PERFORM bdc_field USING 'RC29N-WERKS' g_my_rec_in-werks.
PERFORM bdc_field USING 'RC29N-STLAN' g_my_rec_in-stlan.
PERFORM bdc_field USING 'RC29N-STLAL' g_my_rec_in-stlal.
PERFORM bdc_field USING 'RC29N-DATUV' g_my_rec_in-datuv.
next screen
PERFORM bdc_dynpro USING 'SAPLCSDI' '0110'.
PERFORM bdc_field USING 'BDC_CURSOR' 'RC29K-BMENG'.
PERFORM bdc_field USING 'BDC_OKCODE' '/00'.
PERFORM bdc_field USING 'RC29K-STKTX' g_my_rec_in-stktx.
PERFORM bdc_field USING 'RC29K-BMENG' g_my_rec_in-bmeng.
*next screen
PERFORM bdc_dynpro USING 'SAPLCSDI' '0111'.
PERFORM bdc_field USING 'BDC_CURSOR' 'RC29K-LABOR'.
ENDFORM. " insert_screen_header
*& Form insert_bdc
Insert the BDC session
FORM insert_bdc_new .
CALL FUNCTION 'BDC_INSERT'
EXPORTING
tcode = 'CS01'
POST_LOCAL = NOVBLOCAL
PRINTING = NOPRINT
SIMUBATCH = ' '
CTUPARAMS = ' '
TABLES
dynprotab = i_bdc_table
EXCEPTIONS
internal_error = 1
not_open = 2
queue_error = 3
tcode_invalid = 4
printing_invalid = 5
posting_invalid = 6
OTHERS = 7
IF sy-subrc <> 0.
MESSAGE ID sy-msgid TYPE sy-msgty NUMBER sy-msgno
WITH sy-msgv1 sy-msgv2 sy-msgv3 sy-msgv4.
ENDIF.
CLEAR i_bdc_table[].
ENDFORM. " insert_bdc
*& Form close_bdc_session
Close the BDC session
FORM close_bdc_session .
CALL FUNCTION 'BDC_CLOSE_GROUP'
EXCEPTIONS
not_open = 1
queue_error = 2
OTHERS = 3.
IF sy-subrc <> 0.
MESSAGE ID sy-msgid TYPE sy-msgty NUMBER sy-msgno
WITH sy-msgv1 sy-msgv2 sy-msgv3 sy-msgv4.
ENDIF.
ENDFORM. " close_bdc_session
*& Form f_load_input_file
Load the file into the Internal table
FORM f_load_input_file.
IF p_rloc1 = zc_yes.
CALL FUNCTION 'WS_UPLOAD'
EXPORTING
filename = p_fname1
filetype = 'DAT'
TABLES
data_tab = i_bom
EXCEPTIONS
conversion_error = 1
file_open_error = 2
file_read_error = 3
invalid_type = 4
no_batch = 5
unknown_error = 6
invalid_table_width = 7
gui_refuse_filetransfer = 8
customer_error = 9
OTHERS = 10.
IF sy-subrc <> 0.
MESSAGE ID sy-msgid TYPE sy-msgty NUMBER sy-msgno
WITH sy-msgv1 sy-msgv2 sy-msgv3 sy-msgv4.
STOP.
ENDIF.
ENDIF.
ENDFORM. " f_load_input_file
*& Form release_bdc
Release BDC session
FORM release_bdc.
SUBMIT rsbdcsub WITH mappe EQ p_group
WITH von EQ sy-datum
WITH bis EQ sy-datum
WITH fehler EQ '.'
EXPORTING LIST TO MEMORY
AND RETURN.
ENDFORM. " release_bdc
*& Form item_text_insert
Repetitive code in the screen flow
FORM item_text_insert.
PERFORM bdc_dynpro USING 'SAPLCSDI' '0131'.
PERFORM bdc_field USING 'BDC_OKCODE' '/00'.
PERFORM bdc_field USING 'BDC_CURSOR' 'RC29P-POTX1'.
PERFORM bdc_field USING 'RC29P-POTX1' i_bom-potx1.
ENDFORM. " item_text_insert -
when i call someone who already connected with another call it doesn't show any wating notification. why? it is very important. all other mobiles have this option. Please give me some solution.
Your iPhone can take multiple calls. If you answer your phone from one person or call someone and another call comes into you, you will hear a beep and if you pull your phone away from your ear, you will see that you can hang up the call with the 1st person or answer the 2nd call and then swap between the two.
I have no idea what you mean by you calling someone who is already talking to someone. I've never been able to see on my iPhone that someone I'm calling is already talking to someone else. -
Please give me some material about Oracle forms..!
HI All
This is Narendra ,I did Oracle Certification,now i want to learn Oracle forms also.
Please give me some material if you have it,which test book is good for starting and what all to learn.Please send me if you have any PDF's
Best Regards
Narendra YarapathineniHi You can go through this url : http://www.oracle.com/pls/db102/portal.portal_db?selected=5
And also
http://www.oracle.com/technology/products/forms/htdocs/d2q60.htm
Message was edited by:
user539670 -
Whenever i download any application, i got this message-" the application not installed on the iPhone because an unknown error occurred (0xE800000C)"...Please give me some solutions to resolve this issue..
Read here:
http://support.apple.com/kb/TS3221
Maybe you are looking for
-
Persistant troubles, before and after reinstall and formatting
Hi, I have a 2ghz Macbook Pro with 1gb of Ram. Up until recently it was running the most recent version of 10.4, but one day recently a number of files were corrupted (not sure how many or how) leading to frequent startup troubles. I would start up a
-
I have reset my ipad 2,now it is showing connect to itunes
i have reset my ipad 2,now it is showing connect to itunes. how to fix this problem?
-
Folks, I have deleted the queues as I was not able to restart, Now the inbound side of XI is not receiving anything, Please tell me what is the issue . Manish
-
I have noticed that Safari does not support some HTML commands on this operating platform. Can anybody throw any light on this issue please?
-
Keeps telling me to agree to terms but saying unable to connect to server
Since I updated the software it wont let me turn on icloud until I agree to the new terms. When I try it says "Unable to connect to server" I have tried turning my phone on wi-fi, with out wi=fi, restarting it etc nothing works!