Anchoring multiple Guest SSIDs to the same WLC
Hi All,
I've currently got a typical 'anchored' Guest WLAN solution where several WLCs tunnel guest traffic back to an isolated WLC for WebAuth - this all works fine using a mix of 5508 / 4400, all on v7.0.98.0 code.
The question is, can I add a second Guest SSID to the estate and anchor it back to the same Guest Anchor WLC that I'm already using?
I can't find anything to say it won't work and have found this that says it should, but none of this is very concrete... Does anybody know of any better references and/or have you done this in the wild?
https://supportforums.cisco.com/message/1276785
Cheers,
Richard
Hi,
yes it's totally ok.
On the foreign, just create a second WLAN and anchor it to the other WLC. On the anchor, create the same second WLAN that you anchor to itself ...
Nothing speciali in order to configure it.
Nicolas
===
Don't forget to rate answers that you find useful
Similar Messages
-
I have a Problem with Romming Between SSIDs withing the same WLC but with deferent VLAN .
HI All,
I have a Problem with Romming Between SSIDs withing the same WLC but with deferent VLAN . the WLC are providing the HQ and one of the Branches the Wireless services .
Am using all the available 9 SSIDs at the HQ , and am using only 4 of it at the Brnche.
The problem that i have are happening only at the Branch office as i cant room between the SSIDs within Diferent VLANs but i can do it with the one that pointing to the same VLAN. Once the client ( Laptop/Phone ) connected to one of the SSIDs. it imposiible to have him connected to the other ones with Different VLAN. meanwhile, It says its connected to the other SSID but its not getting IP from that pool.
here is the Show Run-Config from my WLC .. and the Problem happening between the SSID AMOBILE and ASTAFF. i have the Debug while am switching between the SSIDs if needed .
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.11.04 10:20:47 =~=~=~=~=~=~=~=~=~=~=~=
show run-config
Press Enter to continue...
System Inventory
NAME: "Chassis" , DESCR: "Cisco 5500 Series Wireless LAN Controller"
PID: AIR-CT5508-K9, VID: V01, SN: FCW1535L01G
Burned-in MAC Address............................ 30:E4:DB:1B:99:80
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 12
Press Enter to continue or <ctrl-z> to abort
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.0.235.0
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console 1.27
Build Type....................................... DATA + WPS
System Name...................................... WLAN Controller 5508
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 10.125.18.15
Last Reset....................................... Software reset
System Up Time................................... 41 days 5 hrs 14 mins 42 secs
System Timezone Location......................... (GMT -5:00) Eastern Time (US and Canada)
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... US - United States
--More or (q)uit current module or <ctrl-z> to abort
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +36 C
External Temperature............................. +20 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 10
Number of Active Clients......................... 61
Burned-in MAC Address............................ 30:E4:DB:1B:99:80
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 12
Press Enter to continue or <ctrl-z> to abort
AP Bundle Information
Primary AP Image Size
ap3g1 5804
ap801 5192
ap802 5232
c1100 3096
c1130 4972
c1140 4992
c1200 3364
c1240 4812
c1250 5512
c1310 3136
c1520 6412
c3201 4324
c602i 3716
Secondary AP Image Size
ap801 4964
c1100 3036
--More or (q)uit current module or <ctrl-z> to abort
c1130 4884
c1140 4492
c1200 3316
c1240 4712
c1250 5064
c1310 3084
c1520 5244
c3201 4264
Press Enter to continue or <ctrl-z> to abort
Switch Configuration
802.3x Flow Control Mode......................... Disable
FIPS prerequisite features....................... Disabled
secret obfuscation............................... Enabled
Strong Password Check Features:
case-check ...........Enabled
consecutive-check ....Enabled
default-check .......Enabled
username-check ......Enabled
Press Enter to continue or <ctrl-z> to abort
Network Information
RF-Network Name............................. OGR
Web Mode.................................... Disable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Enable
OCSP........................................ Disabled
OCSP responder URL..........................
Secure Shell (ssh).......................... Enable
Telnet...................................... Disable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
AP Multicast/Broadcast Mode................. Unicast
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
IGMP Query Interval......................... 20 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Enabled
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Disable
Mgmt Via Dynamic Interface.................. Disable
--More or (q)uit current module or <ctrl-z> to abort
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
AP Fallback ................................ Enable
Web Auth Redirect Ports .................... 80
Web Auth Proxy Redirect ................... Disable
Fast SSID Change ........................... Enabled
AP Discovery - NAT IP Only ................. Enabled
IP/MAC Addr Binding Check .................. Enabled
Press Enter to continue or <ctrl-z> to abort
Port Summary
STP Admin Physical Physical Link Link
Pr Type Stat Mode Mode Status Status Trap POE SFPType
1 Normal Forw Enable Auto 1000 Full Up Enable N/A 1000BaseTX
2 Normal Disa Enable Auto Auto Down Enable N/A Not Present
3 Normal Disa Enable Auto Auto Down Enable N/A Not Present
4 Normal Disa Enable Auto Auto Down Enable N/A Not Present
5 Normal Disa Enable Auto Auto Down Enable N/A Not Present
6 Normal Disa Enable Auto Auto Down Enable N/A Not Present
7 Normal Disa Enable Auto Auto Down Enable N/A Not Present
8 Normal Disa Enable Auto Auto Down Enable N/A Not Present
Press Enter to continue or <ctrl-z> to abort
AP Summary
Number of APs.................................... 8
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
KNOWLOGY_DC01 2 AIR-LAP1131AG-A-K9 00:1d:45:86:ed:4e KNOWLOGY_DC_Serv 1 US 1
KNOWLOGY_DC02 2 AIR-LAP1131AG-A-K9 00:21:d8:36:c5:c4 KNOWLOGY_DC_Serv 1 US 1
KN1252_AP01 2 AIR-LAP1252AG-A-K9 00:21:d8:ef:06:50 Knowlogy Confere 1 US 1
KN1252_AP02 2 AIR-LAP1252AG-A-K9 00:22:55:8e:2e:d4 Server Room Side 1 US 1
Anham_AP03 2 AIR-LAP1142N-A-K9 70:81:05:88:15:b5 default location 1 US 1
ANHAM_AP01 2 AIR-LAP1142N-A-K9 70:81:05:b0:e4:62 Small Conference 1 US 1
ANHAM_AP04 2 AIR-LAP1131AG-A-K9 00:1d:45:86:e1:b8 Conference room 1 US 1
ANHAM_AP02 2 AIR-LAP1142N-A-K9 70:81:05:96:7a:49 Copy Room 1 US 1
AP Tcp-Mss-Adjust Info
AP Name TCP State MSS Size
KNOWLOGY_DC01 disabled -
KNOWLOGY_DC02 disabled -
--More or (q)uit current module or <ctrl-z> to abort
KN1252_AP01 disabled -
KN1252_AP02 disabled -
Anham_AP03 disabled -
ANHAM_AP01 disabled -
ANHAM_AP04 disabled -
ANHAM_AP02 disabled -
Press Enter to continue or <ctrl-z> to abort
AP Location
Total Number of AP Groups........................ 3
Site Name........................................ ANHAM8075
Site Description................................. ANHAM 8075 Location
WLAN ID Interface Network Admission Control Radio Policy
1 knowlogy_ogr Disabled None
6 knowlogy_ogr Disabled None
9 knowlogy_ogr Disabled None
7 knowlogy_ogr Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
Anham_AP03 2 AIR-LAP1142N-A-K9 70:81:05:88:15:b5 default location 1 US 1
ANHAM_AP01 2 AIR-LAP1142N-A-K9 70:81:05:b0:e4:62 Small Conference 1 US 1
ANHAM_AP04 2 AIR-LAP1131AG-A-K9 00:1d:45:86:e1:b8 Conference room 1 US 1
ANHAM_AP02 2 AIR-LAP1142N-A-K9 70:81:05:96:7a:49 Copy Room 1 US 1
Site Name........................................ Knowlogy_DC
--More or (q)uit current module or <ctrl-z> to abort
Site Description................................. DC Center Access points
WLAN ID Interface Network Admission Control Radio Policy
2 knowlogy_ogr Disabled None
4 knowlogy_ogr Disabled None
3 knowlogy_ogr Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
KNOWLOGY_DC01 2 AIR-LAP1131AG-A-K9 00:1d:45:86:ed:4e KNOWLOGY_DC_Serv 1 US 1
KNOWLOGY_DC02 2 AIR-LAP1131AG-A-K9 00:21:d8:36:c5:c4 KNOWLOGY_DC_Serv 1 US 1
Site Name........................................ OGR
Site Description................................. 1934 OGR Office
WLAN ID Interface Network Admission Control Radio Policy
1 knowlogy_ogr Disabled None
2 knowlogy_ogr Disabled None
4 knowlogy_ogr Disabled None
6 knowlogy_ogr Disabled None
--More or (q)uit current module or <ctrl-z> to abort
7 knowlogy_ogr Disabled None
9 knowlogy_ogr Disabled None
8 knowlogy_ogr Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
KN1252_AP01 2 AIR-LAP1252AG-A-K9 00:21:d8:ef:06:50 Knowlogy Confere 1 US 1
KN1252_AP02 2 AIR-LAP1252AG-A-K9 00:22:55:8e:2e:d4 Server Room Side 1 US 1
Site Name........................................ default-group
Site Description................................. <none>
WLAN ID Interface Network Admission Control Radio Policy
1 knowlogy_ogr Disabled None
2 knowlogy_ogr Disabled None
3 knowlogy_ogr Disabled None
4 knowlogy_ogr Disabled None
5 knowlogy_ogr Disabled None
6 knowlogy_ogr Disabled None
7 knowlogy_ogr Disabled None
8 knowlogy_ogr Disabled None
--More or (q)uit current module or <ctrl-z> to abort
9 knowlogy_ogr Disabled None
10 management Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
Press Enter to continue or <ctrl-z> to abort
AP Config
Cisco AP Identifier.............................. 6
Cisco AP Name.................................... KNOWLOGY_DC01
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:86:ed:4e
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.100
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................ wireless.knowlogy.com
Primary Cisco Switch IP Address.................. 10.125.18.15
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
--More or (q)uit current module or <ctrl-z> to abortIP Address.................. 10.125.18.15
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
--More or (q)uit current module or <ctrl-z> to abort
Reset Button..................................... Enabled
AP Serial Number................................. FTX1134T0QG
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 48 days, 20 h 19 m 18 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:33 2013
Join Taken Time.................................. 0 days, 00 h 10 m 47 s
--More or (q)uit current module or <ctrl-z> to abort
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211b
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:71:09:8f:90
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
--More or (q)uit current module or <ctrl-z> to abort
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
--More or (q)uit current module or <ctrl-z> to abort
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy DSSS parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 11
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
Current CCA Mode .......................... 0
ED Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
--More or (q)uit current module or <ctrl-z> to abort
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Cisco AP Identifier.............................. 6
Cisco AP Name.................................... KNOWLOGY_DC01
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:86:ed:4e
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.100
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
--More or (q)uit current module or <ctrl-z> to abort
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................ wireless.knowlogy.com
Primary Cisco Switch Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
--More or (q)uit current module or <ctrl-z> to abort
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
Reset Button..................................... Enabled
AP Serial Number................................. FTX1134T0QG
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
--More or (q)uit current module or <ctrl-z> to abort
AP Up Time....................................... 48 days, 20 h 19 m 18 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:33 2013
Join Taken Time.................................. 0 days, 00 h 10 m 47 s
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Radio Subband................................ RADIO_SUBBAND_ALL
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:71:09:8f:90
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
--More or (q)uit current module or <ctrl-z> to abort
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... MANDATORY
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 20
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
--More or (q)uit current module or <ctrl-z> to abort
Tx Power
Num Of Supported Power Levels ............. 7
Tx Power Level 1 .......................... 15 dBm
Tx Power Level 2 .......................... 14 dBm
Tx Power Level 3 .......................... 11 dBm
Tx Power Level 4 .......................... 8 dBm
Tx Power Level 5 .......................... 5 dBm
Tx Power Level 6 .......................... 2 dBm
Tx Power Level 7 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 44
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
......................................... 104,108,112,116,132,136,140,
......................................... 149,153,157,161
TI Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
--More or (q)uit current module or <ctrl-z> to abort
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Press Enter to continue or <ctrl-z> to abort
Cisco AP Identifier.............................. 3
Cisco AP Name.................................... KNOWLOGY_DC02
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:21:d8:36:c5:c4
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.101
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
--More or (q)uit current module or <ctrl-z> to abort
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Enabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
Reset Button..................................... Enabled
--More or (q)uit current module or <ctrl-z> to abort
AP Serial Number................................. FTX1230T24F
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 48 days, 20 h 24 m 41 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:35 2013
Join Taken Time.................................. 0 days, 00 h 10 m 48 s
--More or (q)uit current module or <ctrl-z> to abort
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211b
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:22:55:a5:0c:30
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
--More or (q)uit current module or <ctrl-z> to abort
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
--More or (q)uit current module or <ctrl-z> to abort
Current Tx Power Level .................... 1
Phy DSSS parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 1
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
Current CCA Mode .......................... 0
ED Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
--More or (q)uit current module or <ctrl-z> to abort
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Cisco AP Identifier.............................. 3
Cisco AP Name.................................... KNOWLOGY_DC02
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:21:d8:36:c5:c4
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.101
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
--More or (q)uit current module or <ctrl-z> to abort
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Enabled
PoE Power Injector MAC Addr...................... Disabled
--More or (q)uit current module or <ctrl-z> to abort
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
Reset Button..................................... Enabled
AP Serial Number................................. FTX1230T24F
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
--More or (q)uit current module or <ctrl-z> to abort
AP Up Time....................................... 48 days, 20 h 24 m 41 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:35 2013
Join Taken Time.................................. 0 days, 00 h 10 m 48 s
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Radio Subband................................ RADIO_SUBBAND_ALL
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:22:55:a5:0c:30
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
--More or (q)uit current module or <ctrl-z> to abort
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... MANDATORY
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 20
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
--More or (q)uit current module or <ctrl-z> to abort
Tx Power
Num Of Supported Power Levels ............. 7
Tx Power Level 1 .......................... 15 dBm
Tx Power Level 2 .......................... 14 dBm
Tx Power Level 3 .......................... 11 dBm
Tx Power Level 4 .......................... 8 dBm
Tx Power Level 5 .......................... 5 dBm
Tx Power Level 6 .......................... 2 dBm
Tx Power Level 7 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 36
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
......................................... 104,108,112,116,132,136,140,
......................................... 149,153,157,161
TI Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
--More or (q)uit current module or <ctrl-z> to abort
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Press Enter to continue or <ctrl-z> to abort
Cisco AP Identifier.............................. 5
Cisco AP Name.................................... KN1252_AP01
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:21:d8:ef:06:50
IP Address Configuration......................... DHCP
IP Address....................................... 10.125.18.101
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 10.125.18.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Enabled
Ssh State........................................ Disabled
Cisco AP Location................................ Knowlogy Conference Rooms Side
Cisco AP Group Name.............................. OGR
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
--More or (q)uit current module or <ctrl-z> to abort
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.4.10.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. PoE/Medium Power (15.4 W)
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1252AG-A-K9
AP Image......................................... C1250-K9W8-M
IOS Version...................................... 12.4(23c)JA5
--More or (q)uit current module or <ctrl-z> to abort
Reset Button..................................... Enabled
AP Serial Number................................. FTX122990L5
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 118
WLAN 1 :........................................ 111
WLAN 2 :........................................ 111
WLAN 4 :........................................ 112
WLAN 6 :........................................ 112
WLAN 7 :........................................ 111
WLAN 9 :........................................ 112
WLAN 8 :........................................ 112
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 26 days, 00 h 24 m 39 s
--More or (q)uit current module or <ctrl-z> to abort
AP LWAPP Up Time................................. 26 days, 00 h 23 m 48 s
Join Date and Time............................... Wed Oct 9 10:59:07 2013
Join Taken Time.................................. 0 days, 00 h 00 m 50 s
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211n-2.4
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 7
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:22:55:df:a5:90
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
--More or (q)uit current module or <ctrl-z> to abort
11000 Kilo Bits.......................... MANDATORY
MCS Set
MCS 0.................................... SUPPORTED
MCS 1.................................... SUPPORTED
MCS 2.................................... SUPPORTED
MCS 3.................................... SUPPORTED
MCS 4.................................... SUPPORTED
MCS 5.................................... SUPPORTED
MCS 6.................................... SUPPORTED
MCS 7.................................... SUPPORTED
MCS 8.................................... SUPPORTED
MCS 9.................................... SUPPORTED
MCS 10................................... SUPPORTED
MCS 11................................... SUPPORTED
MCS 12................................... SUPPORTED
MCS 13................................... SUPPORTED
MCS 14................................... SUPPORTED
MCS 15................................... SUPPORTED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
--More or (q)uit current module or <ctrl-z> to abort
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 ..........Well you need to understand the behavior of h-reap or what it's called now, FlexConnect. In this mode, the clients are still remembers on the WLC until the session timer/idle timer expires. So switching between SSID's in h-reap will not be the same when switching when the AP's are in local mode.
Take a look at the client when connected in FlexConnect in the WLC GUI monitor tab. Thus will show you what ssid and vlan the client is on. Now switch to a different ssid and compare this. It's probably the same because the client has not timed out. Now go back to the other ssid and look again. Now on the WLC, remove or delete the client and then switch to the other ssid at the same time. Or switch SSID's and then remove the client. The client will join the new ssid and in the monitor tab, you should see the info.
There is no need to have clients have multiple SSID's unless your testing. Devices should only have one ssid profile configured to eliminate any connectivity issues from the device wanting to switch SSID's.
Sent from Cisco Technical Support iPhone App -
3850 WLC - 5760 Anchor: Multiple Guest SSIDs issue
Hi,
I have configured a 3850 Foreign WLC and a 5760 as anchor WLC in a DMZ behind an ASA FW. The Anchor Controller is configured to advertise 3 GUEST Wireless:
(INSIDE) ---- ASA FW (guest in interface) -------------------------- (Te1/0/1) 5760 ANCHOR (Te1/0/2) -------------------- L3 Link-------------------- (guest out interface) ASA FW ---- (OUTSIDE)
GUEST1: 10.9.65.0/24 – VLAN 11
GUEST2: 10.9.66.0/24 – VLAN 12
GUEST3: 10.9.67.0/24 – VLAN 13
Management VLAN 1: 10.8.252.1 (Anchor Management VLAN – Mobility)
The link between the WLC and the Guest OUT Interface on the ASA Firewall is a L3 Link, NOT a Trunk.
The 5760 WLC is also a DHCP server for the three client VLANs above. I have also configured 3 SVIs as default gateways for these VLANs:
Interface vlan 11 – 10.9.65.1
Interface vlan 12 – 10.9.66.1
Interface vlan 13 – 10.9.67.1
wgh-anchorwlc5760-primary#show ip interface brief
Interface IP-Address OK? Method Status Protocol
Vlan1 10.8.252.1 YES NVRAM up up
Vlan11 10.9.65.1 YES manual up up
Vlan12 10.9.66.1 YES manual up up
Vlan13 10.9.67.1 YES manual up up
GigabitEthernet0/0 10.8.252.85 YES NVRAM down down
Te1/0/1 unassigned YES unset up up
Te1/0/2 10.8.253.1 YES NVRAM up up
Capwap0 unassigned YES unset up up
If a client connects to GUEST1 SSID it gets an IP address in VLAN 11 and its default gateway is 10.9.65.1.
If a client connects to GUEST2 SSID it gets an IP address in VLAN 12 and its default gateway is 10.9.66.1.
If a client connects to GUEST3 SSID it gets an IP address in VLAN 13 and its default gateway is 10.9.67.1.
Mobility is UP and I can see clients connected to the Anchor WLC either in IPLEARN or WEBAUTH_PEND state. DHCP is working fine, clients get an IP and the right default gateway and DNS servers when connect, for example, to GUEST1.
anchorwlc5760-primary#show wireless client summary
Number of Local Clients : 3
MAC Address AP Name WLAN State Protocol
04f7.e482.b21c N/A 2 IPLEARN Mobile
bc3e.6d32.17f6 N/A 2 IPLEARN Mobile
a826.d5b3.5ae8 N/A 2 WEBAUTH_PEND Mobile
However, they are not able to ping the default gateway – SVI VLAN 11: 10.9.65.1, so I can not see any traffic leaving the Anchor WLC to continue with the Web Authentication Process (cwa) using ISE. I can see that the authorization policy (“unkown” and the URL to ISE) has been pushed to the clients but I am not redirected to ISE Web Authentication Portal when I open my web browser. I have done some captures on the FW interfaces but I cannot see any traffic coming from the clients.
I know that usually there is a Trunk (that allows client VLANs) between a WLC and L3 Switch when you configure multiples SSIDs and then configure the SVIs on the L3 Switch. However, I think this design with a L3 Link should work too because 5760 is a WLC+L3Switch.
My question is: Why clients are not able to ping their default gateway?
I hope it makes sense.
I appreciate any thoughts and help. Thanks in advance.
Joana.Hi,
I couldn't get it working (I doubt if it is really possible). I had to add a switch between the 5760 Anchor Controller and the ASA Firewall:
(INSIDE) ---- ASA FW (guest in interface) -------------------------- (Te1/0/1) 5760 ANCHOR (Te1/0/2) -------------------- SWITCH-------------------- (guest out interface) ASA FW ---- (OUTSIDE)
The link between the 5760 and the Switch is configured as a Trunk and it allows the 3 Guest SSIDs (VLANs). The link between the Switch and the ASA FW is configured as a Layer 3 link. I also set up the default gateways for the 3 GUEST VLANs in the Switch (3 vlan interfaces) and the 5760 as DHCP Server.
I hope it helps.
Joana. -
NAC Guest Server and Multiple Guest SSID's/Splashpages
Hi All,
If I have multiple guest SSID's on a single controller and I use NGS as the Radius. How do I configure NGS to "send" the clients to differnet login pages corresponding to the SSID they came from.
I can configure different splash pages in HotSpots section but how do I map the different SSID's from the controller to the different splash pages. Then I guess that raises the question when I generate guest users on NGS is it possile to only allow them associate to a specific SSID.
TIA,
Eoin.Hi Nicolas,
Thanks for the reply. I can see that config on the WLC and have used it before where there is only a single guest SSID. What I dont know is if the NAC Guest server sees radius requests coming from different guest SSID's on the same WLC. How does the NAC Guest server apply the correct guest policy to that user. And when sponsors genereate guest accounts how do they specific which policy is to be applied to that guest so it can only get access to a specfic guest network/SSID I'm not sure where the "mapping" of accounts/splash pages/policies takes place on the NAC guest server. I've only ever set up NAC Guest when there has been a single guest SSID.
Regards,
Eoin. -
RE: multiple named objects with the same name andinterface
David,
First I will start by saying that this can be done by using named anchored
objects and registering them yourself in the name service. There is
documentation on how to do this. And by default you will get most of the
behavior you desire. When you do a lookup in the name service (BindObject
method) it will first look in the local partition and see if there is a
local copy and give you that copy. By anchoring the object and manually
registering it in the name service you are programmatically creating your
own SO without defining it as such in the development environment. BTW in
response to your item number 1. This should be the case there as well. If
your "mobile" object is in the same partition where the service object he is
calling resides, you should get a handle to the local instance of the
service object.
Here is the catch, if you make a bind object call and there is no local copy
you will get a handle to a remote copy but you can not be sure which one!
It end ups as more or less a random selection. Off the top of my head and
without going to the doc, I am pretty sure that when you register an
anchored object you can not limit it's visibility to "User".
Sean
-----Original Message-----
From: [email protected]
[<a href="mailto:[email protected]">mailto:[email protected]]On</a> Behalf Of David Foote
Sent: Monday, June 22, 1998 4:51 PM
To: [email protected]
Subject: multiple named objects with the same name and interface
All,
More than once, I have wished that Forte allowed you to place named
objects with the same name in more than one partition. There are two
situations in which this seems desirable:
1) Objects that are not distributed, but are mobile (passed by value to
remote objects), cannot safely reference a Service Object unless it has
environment visibility, but this forces the overhead of a remote method
call when it might not otherwise be necessary. If it were possible to
place a copy of the same Service Object (with user visibility) in each
partition, the overhead of a remote method call could be avoided. This
would only be useful for a service object whose state could be safely
replicated.
2) My second scenario also involves mobile objects referencing a Service
Object, but this time I would like the behavior of the called Service
Object to differ with the partition from which it is called.
This could be accomplished by placing Service Objects with the same name
and the same interface in each partition, but varying the implementation
with the partition.
Does anyone have any thoughts about why this would be a good thing or a
bad thing?
David N. Foote
Consultant
Get Your Private, Free Email at <a href=
"http://www.hotmail.com">http://www.hotmail.com</a>
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive <URL:<a href=
"http://pinehurst.sageit.com/listarchive/">http://pinehurst.sageit.com/listarchive/</a>>
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive <URL:<a href=
"http://pinehurst.sageit.com/listarchive/">http://pinehurst.sageit.com/listarchive/</a>>David,
First I will start by saying that this can be done by using named anchored
objects and registering them yourself in the name service. There is
documentation on how to do this. And by default you will get most of the
behavior you desire. When you do a lookup in the name service (BindObject
method) it will first look in the local partition and see if there is a
local copy and give you that copy. By anchoring the object and manually
registering it in the name service you are programmatically creating your
own SO without defining it as such in the development environment. BTW in
response to your item number 1. This should be the case there as well. If
your "mobile" object is in the same partition where the service object he is
calling resides, you should get a handle to the local instance of the
service object.
Here is the catch, if you make a bind object call and there is no local copy
you will get a handle to a remote copy but you can not be sure which one!
It end ups as more or less a random selection. Off the top of my head and
without going to the doc, I am pretty sure that when you register an
anchored object you can not limit it's visibility to "User".
Sean
-----Original Message-----
From: [email protected]
[<a href="mailto:[email protected]">mailto:[email protected]]On</a> Behalf Of David Foote
Sent: Monday, June 22, 1998 4:51 PM
To: [email protected]
Subject: multiple named objects with the same name and interface
All,
More than once, I have wished that Forte allowed you to place named
objects with the same name in more than one partition. There are two
situations in which this seems desirable:
1) Objects that are not distributed, but are mobile (passed by value to
remote objects), cannot safely reference a Service Object unless it has
environment visibility, but this forces the overhead of a remote method
call when it might not otherwise be necessary. If it were possible to
place a copy of the same Service Object (with user visibility) in each
partition, the overhead of a remote method call could be avoided. This
would only be useful for a service object whose state could be safely
replicated.
2) My second scenario also involves mobile objects referencing a Service
Object, but this time I would like the behavior of the called Service
Object to differ with the partition from which it is called.
This could be accomplished by placing Service Objects with the same name
and the same interface in each partition, but varying the implementation
with the partition.
Does anyone have any thoughts about why this would be a good thing or a
bad thing?
David N. Foote
Consultant
Get Your Private, Free Email at <a href=
"http://www.hotmail.com">http://www.hotmail.com</a>
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive <URL:<a href=
"http://pinehurst.sageit.com/listarchive/">http://pinehurst.sageit.com/listarchive/</a>>
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive <URL:<a href=
"http://pinehurst.sageit.com/listarchive/">http://pinehurst.sageit.com/listarchive/</a>> -
Hi all -
Newbie question. When I am setting up wireless, will I be able to use 2 different SSIDs on the same vlan?
Example:
dot11 ssid Example1
vlan 2
authentication open eap eap_methods
authentication network-eap eap_methods
dot11 ssid Example2
vlan 2
authentication open eap_methods
authentication network-eap eap_methodsHi James,
Hopefully the attached docs will answer your question:
Cisco Aironet 1100 Series
Using VLANs with Cisco Aironet Wireless Equipment
Deprecated versions of Cisco Aironet software permit binding multiple SSIDs to one VLAN. Current versions do not.
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_example09186a00801d0815.shtml#
Cisco IOS Software Configuration Guide for Cisco Aironet Access Points, 12.2(15)JA
Configuring Multiple SSIDs
vlan vlan-id
(Optional) Assign the SSID to a VLAN on your network. Client devices that associate using the SSID are grouped into this VLAN. You can assign only one SSID to a VLAN.
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_guide_chapter09186a00802085c4.html
Hope this helps!
Rob
Please remember to rate helpful posts....... -
What happens on iCloud (ex. contacts) when multiple family members use the same Apple ID?
What happens on iCloud when multiple family members use the same Apple ID? For example if we all choose to use iCloud for contacts, are they all merged together? We use the same Apple ID so we can use find my iPhone to keep track of the whole family.
Of course if you are both connected to the same iCloud account you have the same contacts - what did you expect?. The contacts live on the server and are read from there by the devices; so as you've both managed to sync your contacts up to iCloud they are now inextricably mixed. You can only delete your contacts by deleting individual ones, and doing that will delete them from your phone as well.
You can only unravel this by
1. In the iCloud contacts page at http://icloud.com, select all the contacts, click on the cogwheel icon at bottom left and choose 'Export vCard'.
2. Sign out of System Preferences>iCloud
3. Create a new Apple ID and open a new iCloud account with it for your own use.
4. Import the vCard back into the iCloud contacts page.
5. Go to http://icloud.com and sign in with the original ID. This is now his ID. Work through the contacts individually deleting the ones you don't want him to have. When done sign out and advise him to change his password.
6. Go to the new iCloud account and delete his contacts individually.
Of course if you have also been syncing calendars and using the same email address there are problems with doing this. -
How do I use multiple local workspaces for the same website in VS2013?
For quite some time I've been using VS2010 with multiple workspaces mapped from the same TFS branch to test different variants of a website in parallel. The internal web server (Cassini) seems quite happy to run multiple versions and simply maps a new port
number for the second and subsequent instances that start up.
We are now looking to move to VS2013, so have to use IISExpress since the 'internal' web server is no longer provided.
How do I configure things so that if I open a single workspace, IISExpress runs against that workspace using the default port number (specified in the solution), but if I open a second instance in a different workspace it correctly uses a new port number
and working folder. Do I need to invoke IISExpress using the command line (presumably from each workspace) and specify the relevant defaults or is there some way to enter this in the local config file for IISExpress?
My initial attempt at editing to config file resulted in the 2nd and subsequent instance using the same physicalfolder as the first instance, presumably because the speficied site name and port number are the same!Hello,
Thank you for your post.
I am afraid that the issue is out of support range of VS General Question forum which mainly discusses
the usage of Visual Studio IDE such as WPF & SL designer, Visual Studio Guidance Automation Toolkit, Developer Documentation and Help System
and Visual Studio Editor.
Based on your description, I suggest that you can consult your issue on ASP.NET forum:
http://forums.asp.net/
or IIS forums: http://forums.iis.net/ for better solution and support.
Best regards,
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey. -
How to load multiple HTML5 canvas on the same page (the proper method)
Hi,
I've been struggling to load multiple canvas animations on the same page. At the beggining I thought that exporting the movies with different namespaces and reloading the libraries in a sequential flow might work, but it doesn't. It always loads just the last animation loaded. More info here: Coding challenge: what am I doing wrong?
Here is a sample of what I'm doing:
1st: Publish two flash movies with custom namespaces for "lib" set in the "publish settings": "libFirst" and "libSecond".
2nd: Edit the canvas tags in the HTML page. One called "firstCanvas" and the other one called "secondCanvas"
3rd: Edit the javascript like this:
<script>
// change the default namespace for the CreateJS libraries:
var createjsFirst = createjsFirst||{};
var createjs = createjsFirst;
</script>
<script src="//code.createjs.com/easeljs-0.7.1.min.js"></script>
<script src="//code.createjs.com/tweenjs-0.5.1.min.js"></script>
<script src="//code.createjs.com/movieclip-0.7.1.min.js"></script>
<script src="{{assets}}/js/first.js"></script>
<script>
function initFirstAnimation() {
var canvas, stage, exportRoot;
canvas = document.getElementById("firstCanvas");
exportRoot = new libFirst.first();
stage = new createjsFirst.Stage(canvas);
stage.addChild(exportRoot);
stage.update();
createjsFirst.Ticker.setFPS(libFirst.properties.fps);
createjsFirst.Ticker.addEventListener("tick", stage);
</script>
<script>
// change the default namespace for the CreateJS libraries:
var createjsSecond = createjsSecond||{};
var createjs = createjsSecond;
</script>
<script src="//code.createjs.com/easeljs-0.7.1.min.js"></script>
<script src="//code.createjs.com/tweenjs-0.5.1.min.js"></script>
<script src="//code.createjs.com/movieclip-0.7.1.min.js"></script>
<script src="{{assets}}/js/second.js"></script>
<script>
function initSecondAnimation() {
var canvas, stage, exportRoot;
canvas = document.getElementById("secondCanvas");
exportRoot = new libSecond.second();
stage = new createjsSecond.Stage(canvas);
stage.addChild(exportRoot);
stage.update();
createjsSecond.Ticker.setFPS(libSecond.properties.fps);
createjsSecond.Ticker.addEventListener("tick", stage);
</script>
<body onload="initFirstAnimation(); initSecondAnimation();">
Could someone please reply with the best practice on how to do this? If possible, without the need to reload all the libraries...
If I only need to show one flash movie at a time, would it be more efficient to cut & paste the canvas tag using jQuery in the DOM and reloading a different lib on it?
Many thanks!
#flash #rebornI was able to fix it. At the end, it was easier than I thought. Just have to publish using a different "lib" namespace for each movie, load all the scripts at the end of the <body> and then add the following to the onload or ready events:
$(document).ready(function () {
var canvas, stage, exportRoot;
// First movie
canvas = document.getElementById("firstCanvas");
exportRoot = new libFirst.first();
stage = new createjs.Stage(canvas);
stage.addChild(exportRoot);
stage.update();
createjs.Ticker.setFPS(libFirst.properties.fps);
createjs.Ticker.addEventListener("tick", stage);
// Second movie
canvas = document.getElementById("secondCanvas");
exportRoot = new libSecond.second();
stage = new createjs.Stage(canvas);
stage.addChild(exportRoot);
stage.update();
createjs.Ticker.setFPS(libSecond.properties.fps);
createjs.Ticker.addEventListener("tick", stage);
// Third movie
canvas = dument.getElementById("thirdCanvas");
exportRoot = new libThird.third();
stage = new createjs.Stage(canvas);
stage.addChild(exportRoot);
stage.update();
createjs.Ticker.setFPS(libThird.properties.fps);
createjs.Ticker.addEventListener("tick", stage); -
Can multiple people post on the same shared photo stream?
Is there a way to have multiple people post on the same shared photo stream?
My cousin would like to have a single shared photo stream where we can both post photos on it and comment, instead of having two separate shared photo streams.
We think that there should be an option for the album creator to give access to anyone he/she shares it with to enable them to also post pics on the same stream.The only link I have is to manage your team account http://forums.adobe.com/thread/1460939?tstart=0
The only Adobe program/process for team work that I know of is Adobe Anywhere, but that requires a very different process
Adobe Anywhere http://www.adobe.com/products/adobeanywhere.html
http://www.creativeimpatience.com/adobe-anywhere-enterprise-solution/ -
Can multiple APEX application use the same parsing schema?
Hi,
I have 4.2 APEX thru pl/sql Gatewat, 11gr2 DB and using theme 24.
Due to the APEX limitation for version control I would be splitting 1 big ERP applications into 24 different APEX applications and each application would be considered as 1 unit for version control.
I have about 800 tables and I would assume that all of these would need to be stored in 1 schema since a lot of these table are linked thru FK.
Can I have multiple APEX APPS using the same parsing schema? or is there a better way to do this?
Thanks in advance!Hi,
Multiple applications can have same (one) parsing schema.
You can test that on e.g. apex.oracle.com, where normally you have only one schema and you create multiple applications and all use that same schema.
Regards,
Jari
My Blog: http://dbswh.webhop.net/htmldb/f?p=BLOG:HOME:0
Twitter: http://www.twitter.com/jariolai
Edited by: jarola on Jan 28, 2013 7:15 PM -
Multiple profiles/users on the same device
Hi there,
I know that iOS is a single user environment.
But, I am currently working in an enterprise environment and I was wondering if it was possible to have several profiles on the same device, maybe using certificates or so?
Thanks for your help
Cheers,
Pierre.It would seem that unlike previous iOS devices the iPad and possibly AppleTV call for the ability to enable multiple profiles/users on the same device.
I would suggest that if this capability is not on the roadmap for iOS by now then there is a least one place where alternatives to the iPad will have a major advantage.
The thought they I would have to buy multiple iPads one for myself, my wife and my child because of a software constraint is untenable from a ecological standpoint (all these devices end up as landfill) let alone the economic one.
Also as I use the iPad I see it's potential to become as important computing platform to me as my laptop eventually surpassing it. In this light I can't see how it could remain just a personal device. -
Multiple disconnected users on the same laptop
Has any open come across the following requirement? I have a customer that is interested in 'sharing' laptops with multiple offline users with the ability to sync. Can we have multiple disconnected users on the same laptop? If so what would be the options? The challenge is how to manage multiple extracts on one MWC installation. I suspect that 'OOTB', we only support one extract per machine/installation of the MWC. We may be able to support multiples, but it would take some config/customization.
Please don't post the same question in different forums
Siebel Remote - Can multiple disconnected users be on the same laptop?
multiple disconnected users on the same laptop
Siebel Remote - Can multiple disconnected users be on the same laptop? -
How can i create multiple accounts but use the same itunes?
how can i create multiple accounts but use the same itunes?
Hi iCloud is Making Me Go Crazy,
You will need to create a new Apple ID for your GameCenter and iCloud services. You can continue to use the current Apple ID you share with your Mom for access to iTunes Store purchases if you wish.
Using your Apple ID for Apple services
http://support.apple.com/kb/HT4895
Frequently asked questions about Apple ID
http://support.apple.com/kb/HT5622
Cheers,
- Judy -
Multiple iTunes Accounts on the Same Computer
iTunes states that you can have multiple iTunes accounts on the same computer. But when I attempt to put in a new user account (for my wife so she can have her own music library) my own iTunes account pops up when I go to load iTunes while in her user account. And if I create any account that is NOT an 'Admistrator' account iTunes refuses to install itself as the "user does not have the privileges - consult your Administrator". So I am lost as to what I need to do to create separate iTunes accounts where each person has their own iTunes library and thus their own music. Perplexed...
RobertiTunes states that you can have multiple iTunes accounts on the same computer. But when I attempt to put in a new user account (for my wife so she can have her own music library) my own iTunes account pops up when I go to load iTunes while in her user account. And if I create any account that is NOT an 'Admistrator' account iTunes refuses to install itself as the "user does not have the privileges - consult your Administrator". So I am lost as to what I need to do to create separate iTunes accounts where each person has their own iTunes library and thus their own music. Perplexed...
Robert
Maybe you are looking for
-
Report on changed Purchase order
Dear group Members Warm greetings I am not finding a standard report where i can view list of all changed purchase orders help me to find this report, i will be very thankful to you regards shamul heq
-
TOC and Glossary on PDF export
Is it correct to say that when we export our work to PDF file, we cannot include the auto-generated TOC and Glossary in the PDF output?
-
That pesky Full Screen alert dialog in recent versions of Reader
When I set the preferences within Acrobat to disable that horrible, pesky Full Screen alert dialog, it still appears on the end-user's Reader software, even though I turned it OFF from within Acrobat [slaps forehead]. Is there any way, by hook or by
-
Hi, Version :10.2.0.1 and 11.2.0.1 Os :Aix 5/6 We often getting swap issues.It reached 95%.we have 120GB real memory and 45 GB swap space.The db size is 2.5TB.Some time the db went to hang state and we restarted the db. DB level Is it possible to fin
-
Configuration Validation error when booking an Sales Order.
Hi, Getting an error when booking an sales order ie; "Configuration Validation error". We are upgrading from 11.5.8 to 12.1.1 and this issue is critical. Please provide your valuable suggestion and advice. Thanks in advance, Asif