AnyConnect SSL VPN Vista split-tunneling
I recently setup an ASA5510 with 8.0fw with the AnyConnect SSL VPN Client.
Connecting to the SSL VPN works perfectly from all the XP computers that I have tested from. No problems there. However when on Vista, split-tunneling does not seem to function properly. Everything connects and works fine, and I can get to the defined secured remote nets, however I can't access anything out my default gateway(un-secured traffic). It seems like it might be a problem with Vista security features. When I try to ping out to any outside host, I get:
PING: transmit failed, error code 1231.
I can actually ping my default gateway, but nothing gets routed past it without the above error. I've also confirmed this several Vista installations, with Administrator + UAC disabled. Anyone else?
I have done the same testing, and on both Vista 32bit and 64Bit the split tunneling does not seem to work. Also I found that this is a "known" bug
From the Release Notes::
AnyConnect Split-tunneling Does Not Work on Windows Vista - AnyConnect split-tunneling works correctly with Windows XP and Windows 2000 (CSCsi82315)
I am happy that 64Bit works but will hold off on roll out until split-tunneling is fixed.
Cassidy
Similar Messages
-
Cisco AnyConnect SSL VPN no split tunnel and no hairpinning internet access
Greetings,
I am looking to configure a Cisco ASA 5515X for Cisco AnyConnect Essentials SSL VPN where ALL SSL-VPN traffic is tunneled, no split tunneling or hairpinning on the outside interface. However users require internet access. I need to route traffic out the "trusted" or "inside" interface to another device that performs content-filtering and inspection which then egresses out to the internet from there. Typically this could be done using a route-map (which ASA's do not support) or with a VRF (again, not an option on the ASA). The default route points to the outside interface toward the internet.
Is there no other method to force all my SSL-VPN traffic out the inside interface toward LAN subnets as needed and have another default route point toward the filtering device?
OR
Am I forced to put the ASA behind the filtering device somehow?Hi Jim,
You can use tunnel default route for vpn traffic:
ASA(config)# route inside 0.0.0.0 0.0.0.0 <inside hop> tunneled
configure mode commands/options:
<1-255> Distance metric for this route, default is 1
track Install route depending on tracked item
tunneled Enable the default tunnel gateway option, metric is set to 255
This route is applicable for only vpn traffic.
HTH,
Shetty -
IP Phone SSL VPN and Split tunneling
Hi Team,
I went throught the following document which is very useful:
https://supportforums.cisco.com/docs/DOC-9124
The only things i'm not sure about split-tunneling point:
Group-policy must not be configured with split tunnel or split exclude. Only tunnel all is the supported tunneling policy
I could see many implementation when they used split-tunneling, like one of my customer:
group-policy GroupPolicy1 internal
group-policy GroupPolicy1 attributes
banner value This system is only for Authorized users.
dns-server value 10.64.10.13 10.64.10.14
vpn-tunnel-protocol ssl-client
split-tunnel-policy tunnelspecified
split-tunnel-network-list value split-tunnel
default-domain value prod.mobily.lan
address-pools value SSLClientPool
webvpn
anyconnect keep-installer installed
anyconnect ssl rekey time 30
anyconnect ssl rekey method ssl
anyconnect ask none default anyconnect
username manager-max password XTEsn4mfYvPwC5af encrypted privilege 15
username manager-max attributes
vpn-group-policy GroupPolicy1
tunnel-group PhoneVPN type remote-access
tunnel-group PhoneVPN general-attributes
address-pool SSLClientPool
authentication-server-group AD
default-group-policy GroupPolicy1
tunnel-group PhoneVPN webvpn-attributes
group-url https://84.23.107.10 enable
ip local pool SSLClientPool 10.200.18.1-10.200.18.254 mask 255.255.254.0
access-list split-tunnel remark split-tunnel network list
access-list split-tunnel standard permit 10.0.0.0 255.0.0.0
It is working for them w/o any issue.
My question would be
- is the limitation about split-tunneling still valid? If yes, why it is not recommended?
Thanks!
EvaHi,
If you're not using certificates in client authentication then the SSL handshake will complete before the user is requested to authenticate with username/password. If this authentication request fails you will see the SSL session terminated immediately following this failure (as in the logs you provided). Notice the 5 seconds between the SSL session establishment and termination, this is most likely when the user is being authenticated against the aaa server. If the phone is failing authentication against an external aaa-server you'll want to investigate the logs on that server to determine the root cause of the failure. The ASA can also provide confirmation of the authentication request/reject with the command 'show aaa-server'. If you want to see what's going on at an authentication protocol level you can enable several debugs including "debug aaa authentication|common|internal' and protocol specific debugs such as 'debug radius user|session|all' or 'debug ldap'.
Did this answer your question? If so, please mark it Answered! -
ASA5520 AnyConnect SSL VPN Connected but unable to ping my inside LAN
Hi there, please forgive if I have missed any forum protocols as this is my first post.
I am trying to configure Anyconnect SSL VPN. I am able to connect to the VPN on a laptop, witch is able to download the anyconnect client from the ASA. I am unable to ping any of my IP's that are on the inside of my ASA. Before posting here I have spent many hours on forums and watching videos on anyconnect SSL VPN creation and I am following it to the T but still no ping. Any help would be very much appreciated.
Inside 192.168.1.254/24
Outside dhcp
VPN Pool 192.168.250.1-50/24
Inside LAN 192.168.1.0/24
: Saved
ASA Version 8.4(4)1
interface GigabitEthernet0/0
nameif outside
security-level 0
ip address dhcp setroute
interface GigabitEthernet0/1
nameif inside
security-level 99
ip address 192.168.1.254 255.255.255.0
interface GigabitEthernet0/2
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
nameif management
security-level 99
ip address 192.168.100.1 255.255.255.0
ftp mode passive
dns server-group DefaultDNS
domain-name dock.local
same-security-traffic permit inter-interface
object network inside-network-object
subnet 192.168.1.0 255.255.255.0
object network management-network-object
subnet 192.168.100.0 255.255.255.0
object network NETWORK_OBJ_192.168.250.0_25
subnet 192.168.250.0 255.255.255.128
object-group network AllInside-networks
network-object object inside-network-object
network-object object management-network-object
access-list inside_access_in extended permit ip any any
access-list outside_access_in extended permit icmp any any echo-reply
access-list split_tunnel standard permit 192.168.1.0 255.255.255.0
access-list split_tunnel standard permit 192.168.100.0 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu outside 1500
mtu inside 1500
mtu management 1500
ip local pool vpn_pool 192.168.250.1-192.168.250.100 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-647.bin
no asdm history enable
arp timeout 14400
nat (inside,outside) source dynamic AllInside-networks interface
nat (inside,any) source static any any destination static NETWORK_OBJ_192.168.250.0_25 NETWORK_OBJ_192.168.250.0_25 no-proxy-arp route-lookup
access-group outside_access_in in interface outside
access-group inside_access_in in interface inside
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable 4433
http 192.168.100.0 255.255.255.0 management
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh 192.168.100.0 255.255.255.0 management
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ssl encryption rc4-sha1 aes128-sha1 aes256-sha1 3des-sha1
webvpn
enable outside
anyconnect image disk0:/anyconnect-win-3.1.03103-k9.pkg 1
anyconnect enable
tunnel-group-list enable
group-policy GroupPolicy_anyconnect internal
group-policy GroupPolicy_anyconnect attributes
wins-server none
dns-server value 8.8.8.8
vpn-tunnel-protocol ssl-client ssl-clientless
split-tunnel-policy tunnelall
split-tunnel-network-list value split_tunnel
default-domain value dock.local
username test password JAasdf434ey521ZCT encrypted privilege 15
tunnel-group anyconnect type remote-access
tunnel-group anyconnect general-attributes
address-pool vpn_pool
default-group-policy GroupPolicy_anyconnect
tunnel-group anyconnect webvpn-attributes
group-alias anyconnect enable
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http
https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email
[email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:24bcba3c4124ab371297d52260135924
: end :: Saved
ASA Version 8.4(4)1
interface GigabitEthernet0/0
nameif outside
security-level 0
ip address dhcp setroute
interface GigabitEthernet0/1
nameif inside
security-level 99
ip address 192.168.1.254 255.255.255.0
interface GigabitEthernet0/2
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
nameif management
security-level 99
ip address 192.168.100.1 255.255.255.0
ftp mode passive
dns server-group DefaultDNS
domain-name dock.local
same-security-traffic permit inter-interface
object network inside-network-object
subnet 192.168.1.0 255.255.255.0
object network management-network-object
subnet 192.168.100.0 255.255.255.0
object network NETWORK_OBJ_192.168.250.0_25
subnet 192.168.250.0 255.255.255.0
object-group network AllInside-networks
network-object object inside-network-object
network-object object management-network-object
access-list inside_access_in extended permit ip any any
access-list outside_access_in extended permit icmp any any echo-reply
access-list split_tunnel standard permit 192.168.1.0 255.255.255.0
access-list split_tunnel standard permit 192.168.100.0 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu outside 1500
mtu inside 1500
mtu management 1500
ip local pool Anyconnect-pool 192.168.250.1-192.168.250.100 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-647.bin
no asdm history enable
arp timeout 14400
nat (inside,outside) source dynamic AllInside-networks interface
nat (inside,outside) source static inside-network-object inside-network-object destination static NETWORK_OBJ_192.168.250.0_25 NETWORK_OBJ_192.168.250.0_25
nat (inside,outside) source static management-network-object management-network-object destination static NETWORK_OBJ_192.168.250.0_25 NETWORK_OBJ_192.168.250.0_25
access-group outside_access_in in interface outside
access-group inside_access_in in interface inside
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 192.168.100.2 255.255.255.255 management
http 192.168.100.0 255.255.255.0 management
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh 192.168.100.0 255.255.255.0 management
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
management-access inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ssl encryption rc4-sha1 aes128-sha1 aes256-sha1 3des-sha1
webvpn
enable outside
anyconnect image disk0:/anyconnect-win-3.1.03103-k9.pkg 1
anyconnect enable
tunnel-group-list enable
group-policy GroupPolicy_Anyconnect_VPN internal
group-policy GroupPolicy_Anyconnect_VPN attributes
wins-server none
dns-server value 8.8.8.8
vpn-tunnel-protocol ssl-client
split-tunnel-policy tunnelall
split-tunnel-network-list value split_tunnel
default-domain value dock.local
username sander password f/J.5nLef/EqyPfy encrypted
username aveha password JA8X3IiqPvFFsZCT encrypted privilege 15
tunnel-group Anyconnect_VPN type remote-access
tunnel-group Anyconnect_VPN general-attributes
address-pool Anyconnect-pool
default-group-policy GroupPolicy_Anyconnect_VPN
tunnel-group Anyconnect_VPN webvpn-attributes
group-alias Anyconnect_VPN enable
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http
https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email
[email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:4636fa566ffc11b0f7858b760d974dee
: end: -
Remote Access VPN, no split tunneling, internet access. NAT translation problem
Hi everyone, I'm new to the forum. I have a Cisco ASA 5505 with a confusing (to me) NAT issue.
Single external IP address (outside interface) with multiple static object NAT translations to allow port forwarding to various internal devices. The configuration has been working without issues for the last couple years.
I recently configured a remote access VPN without split tunneling and access to the internet and noticed yesterday that my port forwarding had stopped working.
I reviewed the new NAT rules for the VPN and found the culprit.
I have been reviewing the rules over and over and from everything I can think of, and interpret, I'm not sure how this rule is affecting the port forwarding on the device or how to correct it.
Here are the NAT rules I have in place: (The "inactive" rule is the culprit. As soon as I enable this rule, the port forwarding hits a wall)
nat (inside,outside) source static any any destination static VPN_Subnet VPN_Subnet no-proxy-arp route-lookup
nat (outside,outside) source static VPN_Subnet VPN_Subnet destination static VPN_Subnet VPN_Subnet no-proxy-arp route-lookup
nat (outside,outside) source dynamic VPN_Subnet interface inactive
object network obj_any
nat (inside,outside) dynamic interface
object network XXX_HTTP
nat (inside,outside) static interface service tcp www www
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xxx 1
Any help would be appreciated.Try by changing the nat rule to nat (outside,outside) after-auto source dynamic VPN_Subnet interface
With Regards,
Safwan -
Help with Easy VPN client split tunneling.
Can someone please help me with my config for Easy VPN Client split tunneling. At the moment when the VPN is up I have NO access to the Internet from any host.
Here's what I am attempting to do. I want only certain host to route all there traffic thou the tunnel and the remaining host to use the default route.
I created an object-group and access list with the hosts I want to route thou the VPN :-
object-group network VNPCLIENTS
description HOSTS ALLOWED ACCESS TO THE VPN
host 192.168.3.204
host 192.168.3.42
host 192.168.3.44
host 192.168.3.202
host 192.168.3.43
access-list 1 remark Internet access list
access-list 1 permit 192.168.3.0 0.0.0.255
access-list 101 remark Hosts allowed access to VPN
access-list 101 permit ip object-group VNPCLIENTS any
access-list 111 permit udp any any eq 3074
access-list 111 permit tcp any any eq 3074
access-list 111 permit udp any any eq 88
I Then applied the access list to the Virtual interface of the VPN in both directions:-
interface Virtual-Template1 type tunnel
no ip address
ip access-group 101 in
ip access-group 101 out
tunnel mode ipsec ipv4
Now when I connect to the VPN I have no access from any host to the Internet either thought the tunnel or not.
I must be doing something very wrong. Much appreciate any help.
Thanks
GordonCan someone please help me with my config for Easy VPN Client split tunneling. At the moment when the VPN is up I have NO access to the Internet from any host.
Here's what I am attempting to do. I want only certain host to route all there traffic thou the tunnel and the remaining host to use the default route.
I created an object-group and access list with the hosts I want to route thou the VPN :-
object-group network VNPCLIENTS
description HOSTS ALLOWED ACCESS TO THE VPN
host 192.168.3.204
host 192.168.3.42
host 192.168.3.44
host 192.168.3.202
host 192.168.3.43
access-list 1 remark Internet access list
access-list 1 permit 192.168.3.0 0.0.0.255
access-list 101 remark Hosts allowed access to VPN
access-list 101 permit ip object-group VNPCLIENTS any
access-list 111 permit udp any any eq 3074
access-list 111 permit tcp any any eq 3074
access-list 111 permit udp any any eq 88
I Then applied the access list to the Virtual interface of the VPN in both directions:-
interface Virtual-Template1 type tunnel
no ip address
ip access-group 101 in
ip access-group 101 out
tunnel mode ipsec ipv4
Now when I connect to the VPN I have no access from any host to the Internet either thought the tunnel or not.
I must be doing something very wrong. Much appreciate any help.
Thanks
Gordon -
Anyconnect SSL-VPN - DNS Lookups (external) doesn't work
Hello,
I have issues with my SSL AnyConnect VPN setup on my ASA 5512-x. The VPN , split tunneling and NAT exempt is working fine and i can connect to internal hosts.
However, external or internal DNS requests doesn't work on the clients (Windows, Anyconnect). I want full split tunneling, ie DNS requests should not go through the VPN.
The DNS requests works through NSLOOKUP but not in ping and in any browser.
(The config, request more if i've omitted something important).
ASA Version 8.6(1)2
access-list vlan42-splittunneling standard permit 192.168.42.0 255.255.255.0
ip local pool vlan42test 192.168.199.50-192.168.199.55 mask 255.255.255.0
address-pools value vlan42test
nat (any,any) source static any any destination static VPN-pool-range VPN-pool-range
object network VPN-pool-range
range 192.168.199.10 192.168.199.254
webvpn
enable Outside
anyconnect image disk0:/anyconnect-win-3.1.04072-k9.pkg 1
anyconnect enable
group-policy vlan42-clientvpn-policy internal
group-policy vlan42-clientvpn-policy attributes
wins-server none
vpn-tunnel-protocol ssl-client
split-tunnel-policy tunnelspecified
split-tunnel-network-list value vlan42-splittunneling
default-domain value doesntmatter.local
split-dns value doesntmatter.local
vlan none
address-pools value vlan42test
vpn-group-policy vlan42-clientvpn-policy
vpn-simultaneous-logins 20
service-type remote-access
tunnel-group vlan42-con-profile type remote-access
tunnel-group vlan42-con-profile general-attributes
authentication-server-group ah
default-group-policy vlan42-clientvpn-policy
tunnel-group vlan42-con-profile webvpn-attributes
group-alias privatecloud42 enable
group-url https://vpn.**.com/privatecloud42 enable
I gladly appreciate your help. Thank you.I don't have experience with the ssl client and vista, but I do use the new Anyconnect SSL client with vista. All you need to do is upgrade the ASA to version 8. Hope that helps.
-
Cisco ASA 5505 AnyConnect SSL VPN problem
Hi!
I have a small network, wiht ASA 5505, 8.4:
Inside network: 192.168.2.0/24
Outside: Static IP
I would like to deploy a SSL AnyConnect setup.
The state:
-I give the correct IP from my predefined VPN pool (10.10.10.0/24).
But, could not reach any resource, could not ping too. My host has given 10.10.10.1 IP, and I had a GW: 10.10.10.2. Where is this GW from?
Could you help me?
Here is my config (I omitted my PUBLIC IP, and GW):
Result of the command: "show running-config"
: Saved
ASA Version 8.4(4)1
hostname valamiASA
domain-name valami.local
enable password OeyyCrIqfUEmzen8 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
switchport access vlan 12
interface Vlan1
description LAN
no forward interface Vlan12
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
description WAN
nameif outside
security-level 0
ip address MY_STATIC_IP 255.255.255.248
interface Vlan12
description Vendegeknek a valamiHotSpot WiFi-hez
nameif guest
security-level 100
ip address 192.168.4.1 255.255.255.0
management-only
ftp mode passive
clock timezone GMT 0
dns domain-lookup inside
dns domain-lookup outside
dns domain-lookup guest
dns server-group DefaultDNS
name-server 62.112.192.4
name-server 195.70.35.66
domain-name valami.local
same-security-traffic permit intra-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network inside-net
subnet 192.168.2.0 255.255.255.0
object network guest-net
subnet 192.168.3.0 255.255.255.0
object network NETWORK_OBJ_192.168.2.128_25
subnet 192.168.2.128 255.255.255.128
object-group protocol DM_INLINE_PROTOCOL_3
protocol-object ip
protocol-object icmp
object-group protocol DM_INLINE_PROTOCOL_1
protocol-object ip
protocol-object icmp
object-group protocol DM_INLINE_PROTOCOL_2
protocol-object ip
protocol-object icmp
access-list global_access extended permit object-group DM_INLINE_PROTOCOL_3 any any
access-list AnyConnect_Client_Local_Print extended deny ip any any
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq lpd
access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 631
access-list AnyConnect_Client_Local_Print remark Windows' printing port
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 9100
access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.251 eq 5353
access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.252 eq 5355
access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 137
access-list AnyConnect_Client_Local_Print extended permit udp any any eq netbios-ns
access-list inside_access_in extended permit object-group DM_INLINE_PROTOCOL_2 any any
access-list outside_access_in extended permit object-group DM_INLINE_PROTOCOL_1 any any
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu guest 1500
ip local pool valami_vpn_pool 10.10.10.1-10.10.10.10 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
icmp permit any inside
no asdm history enable
arp timeout 14400
object network inside-net
nat (inside,outside) dynamic interface
object network guest-net
nat (guest,outside) dynamic interface
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
access-group global_access global
route outside 0.0.0.0 0.0.0.0 MY_STATIC_GW 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa local authentication attempts max-fail 16
http server enable
http 192.168.2.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
telnet timeout 5
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics host
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
enable inside
enable outside
anyconnect-essentials
anyconnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
anyconnect enable
tunnel-group-list enable
group-policy GroupPolicy_valami_VPN internal
group-policy GroupPolicy_valami_VPN attributes
wins-server value 192.168.2.2
dns-server value 192.168.2.2
vpn-tunnel-protocol ssl-client
split-tunnel-policy tunnelall
default-domain value valami.local
webvpn
anyconnect ssl rekey time 30
anyconnect ssl rekey method ssl
anyconnect ask enable default anyconnect timeout 30
customization none
deny-message value Login was successful, but because certain criteria have not been met or due to some specific group policy, you do not have permission to use any of the VPN features. Contact your IT administrator for more information.
username test password P4ttSyrm33SV8TYp encrypted
tunnel-group valami_VPN type remote-access
tunnel-group valami_VPN general-attributes
address-pool valami_vpn_pool
default-group-policy GroupPolicy_valami_VPN
tunnel-group valami_VPN webvpn-attributes
group-alias valami_VPN enable
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:d54de340bb6794d90a9ee52c69044753
: endFirst of all thanks your link.
I know your notes, but i don't understand 1 thing:
if i check nat exemption in the anyconnect wizad, why should i make nat exemption rule?
A tried creating a roule, but it is wrong.
My steps (on ASDM):
1: create network object (10.10.10.0/24), named VPN
2: create nat rule: source any, destination VPN, protocol any
Here is my config:
Result of the command: "show running-config"
: Saved
ASA Version 8.4(4)1
hostname companyASA
domain-name company.local
enable password OeyyCrIqfUEmzen8 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
switchport access vlan 12
interface Vlan1
description LAN
no forward interface Vlan12
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
description WAN
nameif outside
security-level 0
ip address 77.111.103.106 255.255.255.248
interface Vlan12
description Vendegeknek a companyHotSpot WiFi-hez
nameif guest
security-level 100
ip address 192.168.4.1 255.255.255.0
ftp mode passive
clock timezone CEST 1
clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00
dns domain-lookup inside
dns domain-lookup outside
dns domain-lookup guest
dns server-group DefaultDNS
name-server 62.112.192.4
name-server 195.70.35.66
domain-name company.local
same-security-traffic permit intra-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network inside-net
subnet 192.168.2.0 255.255.255.0
object network guest-net
subnet 192.168.3.0 255.255.255.0
object network NETWORK_OBJ_192.168.2.128_25
subnet 192.168.2.128 255.255.255.128
object network WEBSHOP
host 192.168.2.2
object network INSIDE_HOST
host 10.100.130.5
object network VOIP_management
host 192.168.2.215
object network Dev_1
host 192.168.2.2
object network Dev_2
host 192.168.2.2
object network RDP
host 192.168.2.2
object network Mediasa
host 192.168.2.17
object network VOIP_ePhone
host 192.168.2.215
object network NETWORK_OBJ_192.168.4.0_28
subnet 192.168.4.0 255.255.255.240
object network NETWORK_OBJ_10.10.10.8_29
subnet 10.10.10.8 255.255.255.248
object network VPN
subnet 10.10.10.0 255.255.255.0
object network VPN-internet
subnet 10.10.10.0 255.255.255.0
object-group protocol DM_INLINE_PROTOCOL_3
protocol-object ip
protocol-object icmp
object-group protocol DM_INLINE_PROTOCOL_1
protocol-object ip
protocol-object icmp
object-group protocol DM_INLINE_PROTOCOL_2
protocol-object ip
protocol-object icmp
access-list global_access extended permit object-group DM_INLINE_PROTOCOL_3 any any
access-list AnyConnect_Client_Local_Print extended deny ip any any
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq lpd
access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 631
access-list AnyConnect_Client_Local_Print remark Windows' printing port
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 9100
access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.251 eq 5353
access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.252 eq 5355
access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 137
access-list AnyConnect_Client_Local_Print extended permit udp any any eq netbios-ns
access-list inside_access_in extended permit object-group DM_INLINE_PROTOCOL_2 any any
access-list outside_access_in extended permit object-group DM_INLINE_PROTOCOL_1 any any
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu guest 1500
ip local pool company_vpn_pool 10.10.10.10-10.10.10.15 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
icmp permit any inside
no asdm history enable
arp timeout 14400
nat (any,any) source static any any destination static VPN VPN
nat (inside,outside) source static inside-net inside-net destination static VPN VPN
object network inside-net
nat (inside,outside) dynamic interface
object network guest-net
nat (guest,outside) dynamic interface
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
access-group global_access global
route outside 0.0.0.0 0.0.0.0 77.111.103.105 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa local authentication attempts max-fail 16
http server enable
http 192.168.2.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
telnet timeout 5
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics host
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
enable inside
enable outside
anyconnect-essentials
anyconnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
anyconnect enable
tunnel-group-list enable
group-policy GroupPolicy_company_VPN internal
group-policy GroupPolicy_company_VPN attributes
wins-server value 192.168.2.2
dns-server value 192.168.2.2
vpn-tunnel-protocol l2tp-ipsec
split-tunnel-policy tunnelall
default-domain value company.local
webvpn
anyconnect ssl rekey time 30
anyconnect ssl rekey method ssl
anyconnect ask enable default anyconnect timeout 30
customization none
deny-message value Login was successful, but because certain criteria have not been met or due to some specific group policy, you do not have permission to use any of the VPN features. Contact your IT administrator for more information.
group-policy GroupPolicy_VPN internal
group-policy GroupPolicy_VPN attributes
wins-server none
dns-server value 62.112.192.4 195.70.35.66
vpn-tunnel-protocol ssl-client
default-domain value company.local
username test password P4ttSyrm33SV8TYp encrypted
tunnel-group company_VPN type remote-access
tunnel-group company_VPN general-attributes
address-pool company_vpn_pool
default-group-policy GroupPolicy_company_VPN
tunnel-group company_VPN webvpn-attributes
group-alias company_VPN enable
tunnel-group VPN type remote-access
tunnel-group VPN general-attributes
address-pool company_vpn_pool
default-group-policy GroupPolicy_VPN
tunnel-group VPN webvpn-attributes
group-alias VPN enable
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
inspect icmp error
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:33ee37a3722f228f9be9b84ef43f731e
: end
Could you give me a CLI-code?
(or ASDM steps). -
VM with remote access VPN without split tunneling
Hello experts,
I have customers who require to use VM in their laptop. These users also require to VPN to Corporate network to do their job. However when they do remote VPN to corporate Network (ASA VPN concentrator) from their VM host machine, they loose their access to their VM guest machines. This problem was not happening when they used cisco VPN client which has gone end of life and support as of end of July 31, 2012. In Cisco VPN client (IKEV1) if we set the protocol to udp they had no problem to keep their connectivity to VM machines while connected to corporate with remote access VPN. However this feature does not work in new Cisco VPN client which is called AnyConnect. ( NOTE: I am using IPSEC IKEV2. NO SSL at this time).
My Question to Experts:
1. Was the ability to maintain connection to VM guest machines, while connected to VPN without enabling split tunneling a security flaw in the old cisco VPN client?
2. Is there a way to maintain connectivy to VM machines installed in a computer and still connect to remote access VPN concentrator through host machine? (My question is about AnyConnect client only using IPSEC IKEV2 and I do not want to enable split tunneling)
Thanks for your help,
RaziDid you figure this out?
-
Anyconnect SSL VPN States Contacting...
I had my ssl vpn working and now the anyconnect client that I downloaded just says Contacting... It will not give me an error at all. If I use the Anyconnect App on my droid phone it says "Anyconnect cannot confirm it is connected to your secure gateway. The local network may not be trustworthy. Please try another network." I previously had the droid app work as well and I have made no changes to the VPN configuration. Here is my config and version numbers:
anyconnect-win-2.5.2014-k9.pkg
c2800nm-adventerprisek9-mz.151-4.M5.bin
webvpn gateway gateway_1
ip interface Dialer1 port 443
ssl trustpoint SSL-VPN
inservice
webvpn install svc flash:/webvpn/anyconnect-win-2.5.2014-k9.pkg sequence 1
webvpn context SSL-VPN
secondary-color white
title-color #CCCC66
text-color black
ssl authenticate verify all
policy group policy_1
functions svc-enabled
svc address-pool "SSL-VPN" netmask 255.255.255.0
svc default-domain "<DOMAIN>"
svc keep-client-installed
svc split include 192.168.0.0 255.255.0.0
svc dns-server primary <IP>
default-group-policy policy_1
gateway gateway_1
inservice
Any suggestions would be greatly appriciated.I had my ssl vpn working and now the anyconnect client that I downloaded just says Contacting... It will not give me an error at all. If I use the Anyconnect App on my droid phone it says "Anyconnect cannot confirm it is connected to your secure gateway. The local network may not be trustworthy. Please try another network." I previously had the droid app work as well and I have made no changes to the VPN configuration. Here is my config and version numbers:
anyconnect-win-2.5.2014-k9.pkg
c2800nm-adventerprisek9-mz.151-4.M5.bin
webvpn gateway gateway_1
ip interface Dialer1 port 443
ssl trustpoint SSL-VPN
inservice
webvpn install svc flash:/webvpn/anyconnect-win-2.5.2014-k9.pkg sequence 1
webvpn context SSL-VPN
secondary-color white
title-color #CCCC66
text-color black
ssl authenticate verify all
policy group policy_1
functions svc-enabled
svc address-pool "SSL-VPN" netmask 255.255.255.0
svc default-domain "<DOMAIN>"
svc keep-client-installed
svc split include 192.168.0.0 255.255.0.0
svc dns-server primary <IP>
default-group-policy policy_1
gateway gateway_1
inservice
Any suggestions would be greatly appriciated. -
Anyconnect SSL VPN Authentication Feilure
Dear All,
I have configured an Asa 5510 as SSL vpn gataway ver 8.2(4) Anyconnect Essential. The clients are authenticated via Radius and OTP password.
All work well since yesterday. When I have did same configuration changes. My objective was has that the clients accept the self signed certificate issued by the Asa whitout give the warning about the private cert.
So I have try to generaste a new certificate with FQDN equal to myasa.mydomain.com and also a CN=myasa
Then I have change the provile XML file of my anyconnect in this way:
<HostEntry>
<HostName>myasa</HostName>
<HostAddress>xxx.xxx.xxx.xxx</HostAddress>
<PrimaryProtocol>SSL</PrimaryProtocol>
Then I installed the certificate on my Win7 Pc in the Trusted Root Certification Authority.
The result of all my changes is that now the login fail! Someone could help me pls?
webvpn_allocate_auth_struct: net_handle = DA0C3608
webvpn_portal.c:ewaFormSubmit_webvpn_login[3203]
webvpn_portal.c:webvpn_login_validate_net_handle[2234]
webvpn_portal.c:webvpn_login_allocate_auth_struct[2254]
webvpn_portal.c:webvpn_login_assign_app_next[2272]
webvpn_portal.c:webvpn_login_cookie_check[2289]
webvpn_portal.c:webvpn_login_set_tg_buffer_from_form[2325]
webvpn_portal.c:webvpn_login_transcend_cert_auth_cookie[2359]
webvpn_login_transcend_cert_auth_cookie: tg_cookie = NULL, tg_name = VPNSSL
webvpn_portal.c:webvpn_login_set_tg_cookie_form[2421]
webvpn_portal.c:webvpn_login_set_tg_cookie_querry_string[2473]
webvpn_portal.c:webvpn_login_resolve_tunnel_group[2546]
webvpn_login_resolve_tunnel_group: tgCookie = NULL
webvpn_login_resolve_tunnel_group: tunnel group name from group list
webvpn_login_resolve_tunnel_group: TG_BUFFER = VPNSSL
webvpn_portal.c:webvpn_login_negotiate_client_cert[2636]
webvpn_portal.c:webvpn_login_check_cert_status[2733]
webvpn_portal.c:webvpn_login_cert_only[2774]
webvpn_portal.c:webvpn_login_primary_username[2796]
webvpn_portal.c:webvpn_login_primary_password[2878]
webvpn_portal.c:webvpn_login_secondary_username[2910]
webvpn_portal.c:webvpn_login_secondary_password[2988]
webvpn_portal.c:webvpn_login_extra_password[3021]
webvpn_portal.c:webvpn_login_set_cookie_flag[3040]
webvpn_portal.c:webvpn_login_set_auth_group_type[3063]
webvpn_login_set_auth_group_type: WEBVPN_AUTH_GROUP_TYPE = 1
webvpn_portal.c:webvpn_login_aaa_not_resuming[3137]
webvpn_portal.c:http_webvpn_kill_cookie[790]
webvpn_auth.c:http_webvpn_pre_authentication[2321]
WebVPN: calling AAA with ewsContext (-636397680) and nh (-636733944)!
webvpn_add_auth_handle: auth_handle = 95
WebVPN: started user authentication...
webvpn_auth.c:webvpn_aaa_callback[5163]
WebVPN: AAA status = (ACCEPT)
webvpn_portal.c:ewaFormSubmit_webvpn_login[3203]
webvpn_portal.c:webvpn_login_validate_net_handle[2234]
webvpn_portal.c:webvpn_login_allocate_auth_struct[2254]
webvpn_portal.c:webvpn_login_assign_app_next[2272]
webvpn_portal.c:webvpn_login_cookie_check[2289]
webvpn_portal.c:webvpn_login_set_tg_buffer_from_form[2325]
webvpn_portal.c:webvpn_login_transcend_cert_auth_cookie[2359]
webvpn_login_transcend_cert_auth_cookie: tg_cookie = NULL, tg_name = VPNSSL
webvpn_portal.c:webvpn_login_set_tg_cookie_form[2421]
webvpn_portal.c:webvpn_login_set_tg_cookie_querry_string[2473]
webvpn_portal.c:webvpn_login_resolve_tunnel_group[2546]
webvpn_portal.c:webvpn_login_negotiate_client_cert[2636]
webvpn_portal.c:webvpn_login_check_cert_status[2733]
webvpn_portal.c:webvpn_login_cert_only[2774]
webvpn_portal.c:webvpn_login_primary_username[2796]
webvpn_portal.c:webvpn_login_primary_password[2878]
webvpn_portal.c:webvpn_login_secondary_username[2910]
webvpn_portal.c:webvpn_login_secondary_password[2988]
webvpn_portal.c:webvpn_login_extra_password[3021]
webvpn_portal.c:webvpn_login_set_cookie_flag[3040]
webvpn_portal.c:webvpn_login_set_auth_group_type[3063]
webvpn_login_set_auth_group_type: WEBVPN_AUTH_GROUP_TYPE = 1
webvpn_portal.c:webvpn_login_aaa_resuming[3093]
webvpn_auth.c:http_webvpn_post_authentication[1485]
WebVPN: user: ([email protected]) authenticated.
webvpn_auth.c:http_webvpn_auth_accept[2939]
WARNING: CSD is disabled by AnyConnect Essentials license.
webvpn_session.c:http_webvpn_create_session[184]
webvpn_session.c:http_webvpn_find_session[159]
WebVPN session created!
webvpn_session.c:http_webvpn_find_session[159]
webvpn_session.c:http_webvpn_destroy_session[1386]
webvpn_remove_auth_handle: auth_handle = 95
WARNING: CSD is disabled by AnyConnect Essentials license.
WARNING: CSD is disabled by AnyConnect Essentials license.
webvpn_portal.c:webvpn_determine_primary_username[5689]
webvpn_portal.c:webvpn_determine_secondary_username[5758]
webvpn_portal.c:ewaFormServe_webvpn_login[1974]
webvpn_portal.c:http_webvpn_kill_cookie[790]
APP_BUFFER: <option value="VPNSSL" noaaa="0" >dntsbewvpn</option>
webvpn_free_auth_struct: net_handle = DA0C3608
webvpn_allocate_auth_struct: net_handle = DA0C3608
webvpn_free_auth_struct: net_handle = DA0C3608Dear All,
I have found why the authentication was stop to work.
I have lost in the config the command:
svc image disk0:/anyconnect-win-xxxxxk9.pkg 1
Now it works.
Best regards,
Igor. -
AnyConnecy VPN and Split-tunnel ACL - Strange...
Hi,
I have ACL as follows and applied on AnyConnect VPN group as split-tunel value ACL.
access-list SPLIT-ACL extended permit tcp host 192.168.200.63 172.16.1.0 255.255.255.0 eq www
access-list SPLIT-ACL extended permit tcp host 192.168.200.63 172.16.1.0 255.255.255.0 eq https
When I connected with AnyConnect client, I can ping to 192.168.200.63 and also telnet to port 80. However I can not telnet to port 443. Strange thing is I do not see any hits on above ACL, morever I'm wondering how cam the ICMP is working and why it does not stop on this ACL..?
Phase: 4
Type: ACCESS-LIST
Subtype:
Result: DROP
Config:
Implicit Rule
Additional Information:
Forward Flow based lookup yields rule:
in id=0x78e03140, priority=11, domain=permit, deny=true
hits=113713, user_data=0x5, cs_id=0x0, use_real_addr, flags=0x0, protocol=0
src ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=0
dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=0 dscp=0x0
input_ifc=outside, output_ifc=any
When I did the packet-tracer both ICMP and http it just drop on Phase 4..as bellow, I just want to know what this ACL and where its been applied to..?
What is the correct syntax for packet-tracer command when troubleshooting AnyConnect VPN to check access inside/dmz server..?
I have used as follows:
packet-tracer input outside icmp 172.16.1.1 0 8 192.168.200.63 details
Appreciate if someone can help me out on this..
thanksTo start with it is not ideal to configure a port based split tunnel. It is not support and will give you weird results like one you are experiencing. You should use standard access-list for the split tunnel and to restrict the users to the following port use vpn filter.
As far as packet tracer is concerned for the VPN client if you use the outside interface as source it will never work the reason is the connection between the ASA and the client is of real IP address (Public) and the traffic that you are testing with is a VPN encrypted traffic your ASA's outside interface doesn't know what is 172.16.1.1, he will check it against the outside access-list and will drop it.
So in your case i would strongly recommed that use standard access-list for the split tunnel and to restrict the user to specific port use vpn filter. Following are the links to configure the same:
Allow Split Tunnel for Anyconnect:
http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a0080975e83.shtml
Configure VPN filter (Its for site to site and remote access but it works the same for Anyconnect):
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a00808c9a87.shtml
Thanks
Jeet Kumar -
Hi Everyone,
I was testing few things at my home lab.
PC---running ssl vpn------------sw------router------------ISP--------------ASA(ssl anyconnect)
anyconnect ssl is working fine and i am also able to access internet.
I am using full tunnel
i have acl on outside interface of ASA
1
True
any
any
ip
Deny
0
Default
i know that ACL is used for traffic passing via ASA.
I need to understand the traffic flow for access to internet via ssl vpn.?
Regards
MAheshAs you say correctly, the interface-ACL is not important for that as the VPN-traffic is not inspected by that ACL. At least not by default.
You can control the traffic with a different ACL that gets applied to the group-policy with the "vpn-filter" command. And of course you need a NAT-rule that translates your traffic when flowing to the internet. That rule has to work on the interface-pair (outside,outside). -
Nokia mobile VPN Client - split tunneling
Hi
I'm trying to get Nokia mobile CPN Client working with split tunneling on a Cisco firewall.
I have full access to all on my internal lan's when I make the VPN tunnel, so tunnel is up and working.
But I do not have access to anything in the internet, it tries to route internet requests through the VPN. I have set split tunneling on the Cisco firewall and it is working as intended on all other devices.
Any ideas of what I have missed?
My policy is based on the bundled Cisco_ASA_pskxauth.pol from the Nokia mobile VPN Client Policy Tool.
tsftsHi vgta2k:
Nokia 5530 XpressMusic is S60 5th edition phone.
http://www.forum.nokia.com/Devices/Device_specifications/5530_XpressMusic/
It runs different version of Nokia Mobile VPN client than Symbian^3. You can find the correct version at the download page:
http://europe.nokia.com/support/download-software/nokia-mobile-vpn/compatibility-and-download
Just use the device selector and pick your phone.
You can also find Nokia Mobile VPN Client nowadays at Ovi Store.
Thanks,
Ismo -
Cisco 3745, VPN and Split Tunneling
I tried following the model here: http://www.cisco.com/en/US/netsol/ns340/ns394/ns171/ns27/networking_solutions_white_paper09186a008018914d.shtml
but after doing so, the situation was actually reversed. While connected to the vpn client you were able to browse the internet but not able to access vpn resources. I undid and redid the configuration several times to rule out keying in problems.
Can one help with this problem... If needed Ill post necessary configs from my router.. Thanks
(btw: do these froms have a search?)I am having the same problems with pix 501. With split tunnel, I get web but no lan access. Without split tunnel, full lan access, no web. My acl for the splitTunnel is:
permit ip host 192.168.1.0 any
Is this wrong?
Maybe you are looking for
-
How to access different Agent from differnt schema in ODI?
Hi, I am new in ODI and doing some practical assignment related to ODI agent. here on one system i.e. 198.168.100.22 my colleague install ODI and another system 198.168.100.21 I also have installed ODI this is my system with different schema of each
-
Has anyone ever reported an issue in maps and had it fixed?
My companies address, telephone number and map marker is still wrong and has been for nearly a year now. I've reported it numerous times.
-
Checking status of a dial up connection
I'm trying to develop a program that checks whether a dial up connection has been established. I'm using a thread to attempt to open a URLConnection every 5 seconds. If opening the connection succeeds the connection status is set to true. If an excep
-
New Authorization Objects after system upgrade
Hi All , I require the list of all new Authorization Objects that have been added to the system after System Update. Regards Anthony D'souza
-
Photoshop Elements 9 Organizer hat ein Problem festgestellt und muss beendet werden.
Mit dieser Popup Meldung verabschiedet sich mein neu installiertes Pse9. Eine Neuinstallation half nicht weiter. Weitere Informationen zum Fehler: AppName: photoshopelementsorganizer.exe AppVer: 9.0.3.0 ModName: pclempegbox.ax ModVer: 4.0.8.0 Offset: