AnyConnect Trusted Network Access Problem

Hi,
I am running a test deployment of AnyConnect with 100 users. The target is to develop the solution to be 'always on' and to easily transition between trusted and non-trusted networks using NAM and VPN modules with certificate based authentication.
I have the following network groups configured:
TRUSTED-WIRED
UNTRUSTED-WIRED
TRUSTED-WIFI
UNTRUSTED-WIFI
The untrusted groups allowed users to add local networks. The trusted groups are centrally controlled and secured.
I had all this working well, but since I upgraded my ASA HA pair I have issues connecting to the internal trusted network. The VPN and certificate based user authentication is working fine. When I try and use the client on the trusted internal network with basic ICMP tests I get the following error message:
C:\>arp -a
Internet Address      Physical Address      Type
10.192.196.1          00-24-97-48-dd-00     dynamic
224.0.0.22            01-00-5e-00-00-16     static
224.0.0.252           01-00-5e-00-00-fc     static
239.255.255.250       01-00-5e-7f-ff-fa     static
255.255.255.255       ff-ff-ff-ff-ff-ff     static
C:\>ping 10.192.196.1
Pinging 10.192.196.1 with 32 bytes of data:
PING: transmit failed. General failure.
PING: transmit failed. General failure.
PING: transmit failed. General failure.
PING: transmit failed. General failure.
Ping statistics for 10.192.196.1:
    Packets: Sent = 4, Received = 0, Lost = 4 (100% loss),
I am actively researching this problem now. I'm not sure if it is directly related to the upgrade or something I have inadvertently configured/selected during the upgrade. It's a test lab/PoC environment but will be going live early in 2013, so I would obviously like to get passed this little issue.
Any other ideas/thoughts would be most welcome in my hour of need!!
Cheers
Dave

having a similar problem with windows 8, worked once, now it wont work again getting same symptoms as you, i see the arp for default gateway, routing table looks correct, but traceroute to internal routes goes out local internet connection and i get general failure when pinging. Let me know if you find anything.

Similar Messages

E3000 guest network access problems

Hi,
I have the E3000 router and am using an Engenious repeater. I only turn on the repeater when I'm playing PS3 because it boosts the signal dramatically. However, if someone in my house is connected to the boosted network when I'm using the PS3 I get horrible lag on my PS3. Yesterday I tried connecting the laptop to my guest network while my PS3 was connected to the boosted network, and it worked great. Now, however, I'm unable to connect to the guest network on my laptop. It takes 2 minutes to identify the network and then when it connects it says no internet access. I have the Cisco connect software installed on the laptop. When i run the windows 7 network troubleshoot it detects a problem with the network adapter and says it resolved the problem, but really it just connects me to my main wireless signal and not the guest one.
Thanks in advance for any help

Guest network is unsecured wireless network and it works on 2.4 GHz wireless band.
If you are able to connect to the main network then I think there should not be any problem to connect to the guest network.
The main network has the IP address in the range of 192.168.1.xxx whereas guest network works on 192.168.33.xxx IP address. You have installed the Cisco connect software on your laptop. I think your laptop might be trying to connect to the main wireless network automatically.
You can try upgrading the firmware on your router and see if that makes any difference.

Iomega Home Media Network Hard Drive network access problem

Hello all Having trouble accessing Iomega media drive ce,web interface is not responding.Iam able to ping ,map and access shares using win7 and winxp systems.Read and writie to shares.Earlier in 2012-13 experienced similar problem,but reimaging using reimager software, fixed the problem.Reimaging didnt destroy data it just reset the user accounts.(atleast in my case).Few days back the problem reoccured.I noticed from my experience, the web interface becomes unresponsive only after enabling cloud with medium or high security.I tried resetting. Also tried to connect drive to pc directly and ran ARP utility.Drive respond to ping(arp provided ip address).,but web interface is still unresponsive.Also cloud invitation email not working.But device status monitor or reporitng email works. I periodically receive email alerts about new firmware,time synching.Please help me restore my drive. Drive details:Home media network CE(shipped firmware 3.2.3.15290 ).Current firmware:3.2.8.30031.Storage manager ver. 1.4.4.14439Router infoSL-2750u (tried using port forwarding/DHCP and port forwarding/Static ip).TZO remote access status:Expired.FTPisabledCloud :enabledWarranty status:Active.(13/12/2015). Thank u

Hello dhanse_k,
For something like this, there really isn't much that I can help with here.
I'm limited to giving advice and that isn't going to help if you have a verified IP that's not granting access to the UI.
I recommend starting a support ticket here:
https://lenovo-ap-en.custhelp.com/app/answers/detail/a_id/18133/session/L3RpbWUvMTM2NjU5MDgxMS9zaWQvSEtSbjZqb2w%3D#phone
It sounds like your NAS is having issues with Apache and starting a support ticket will enable an agent to assist you with that.

ASA 5505 VPN Network access problem

I have been working on this thing all night and I can't seem to get any where. I have a very straight forward set up, and so far the only issue I'm having is being able to access the network when connected through VPN, I have internet access, but nothing else and it's really strange.
Here is my config, I thought this would be a pretty straight forward set up, and I got everything else up and running with in a few minutes, but not being able to access the network via VPN is frustrating after I have tried all night to get it to work. I have read a lot of stuff online, and I keep on thinking im close but never get anywhere. Any help is appreciated.
Attached is the config.
Thanks

Your NAT config confuses me. Are those "static (inside,inside)" lines for real?
try this:
no global (inside) 1 interface
no nat (T1) 1 access-list outside_nat dns
nat (inside) 0 access-list Local_LAN_Access
And remove those dodgy "static (inside,inside)" NATs!
I recommend staying with tunnelling everything.
You should tighten "access-list T1_access_in" because at the moment all IP is allowed from the internet to those "static (inside,T1)" NATs.
If you put "no sysopt connection permit-vpn" then all VPN traffic is forced through "access-list T1_access_in" - an easy way of filtering it.
I would tighten "access-list inside_access_in" but unapply and remove "access-list inside_access_out".

OS X 10.8.3 AnyConnect 2.5.3054 Network Access Unavailable

I am trying to connect using:
AnyConnect 2.5.3054
on Mac OS X 10.8.3
MacPro
via Wifi AirPort on en2
I have just installed AnyConnect. When I start it up I get the following message in the AnyConnect window: "Network Access: Unavailable - No Networks Detected"
If I try to connect a dropdown window appears saying "Warning: The follwing Certificate received from the Server could not be verified" with some other metadata I cannot share.
It then provides me with a username and password fields. After succesfully entering them, it tries to connect and then a dropdown message window appears stating "AnyConnect was not able to estabmish a connection to the specified secure gateway. Please try connecting again."
I can connect using my MacBook Pro using the OS and version of AnyConnect. The difference seems to be the machine type.
I saw the post about 10.6.8 and not using Back-To-My-Mac on MobileMe. I am using iCloud, but Back-To-My-Mac has never been enabled.
Note: I do have network access on the MacPro. That is I can connect via web and email, etc.

Ari,
10.8 Mac support has been only added in Anyconnect 3.1.
Compare:
http://www.cisco.com/en/US/docs/security/vpn_client/anyconnect/anyconnect31/release/notes/anyconnect31rn.html#wp1067508
to:
http://www.cisco.com/en/US/docs/security/vpn_client/anyconnect/anyconnect30/release/notes/anyconnect30rn.html#wp1578101
and
http://www.cisco.com/en/US/docs/security/vpn_client/anyconnect/anyconnect25/release/notes/anyconnect25rn.html#wp1068230
M.

No shared network access when booted from Firewire

I can't seem to access any volumes on my network when my MacMini is booted from an ext. firewire drive. I've tried to do this from two seperate bootable FW drives and I can't access my NAS or any of the other Macs on my network. This is an issue that I just noticed. I have worked with Macs and PCs across networks for a while but I can't figure this one out for some reason.
I'm running MacMini 1.66 GHz Intel Core Duo and I'm on 10.5.8. Any insight is appreciated. Thanks!

UPDATED/SOLVED---I finally figured this problem out. **Note: This whole process began with the desire to expand my original MacMini's 75GB HD space and to avoid potential disaster. I have recently been going through a spate of HD failures and I really wanted to avoid such a calamity with my main system volume. So the goal was to, in effect, replace the MacMini's drive without having to open it up by simply buying a new 1TB drive and dropping it into a FW enclosure with a huge fan. I had hoped that a simple BounceBack recover would do the trick but I quickly found out that it was not to be.
The problem existed on backup copies that were created by my old version (5.1.4) of BounceBack (that I never updated). For whatever reason, that version excludes necessary components for networking when making bootable volumes. Therefore all my external FW drives that were bootable were not truly complete/useable volumes. Here's how I came to that conclusion and how I ultimately solved the problem.
1. I ended up having to do a reinstall of Leopard. I did this by cloning Leopard install disc to an image file and then restoring that image file to the FW drive. The real purpose of cloning the install disc was to immediately test the veracity of my theory that the problem lay within my BounceBack bootable volumes and not with the FW drives themselves. Sure enough, I found everything to be working perfectly from the newly minted, clean install Leopard FW volume. So then...
2. ...I cloned the MacMini's orginal internal HD. It was the only volume with my most recent system that did NOT have the aforementioned network access problems and it was the volume from which all of the other BounceBack volumes were created.
3. I restored this volume to the FW drive and was rewarded with a brand new, expanded and fully working system volume with all my applications and settings intact.
To be fair, I feel compelled to mention that this is not necessarily an indictment of BounceBack. Again, the copy I was using is several years old and I simply never paid for an update, thinking that the copy I was using was sufficient. I'm willing to bet that the makers of BounceBack solved this problem long ago with one of the many updates since that have been released I first purchased the software. That being said, I'm now using Time Machine for backups of my system volume while utilizing BounceBack for data on other volumes that don't need to be bootable.

Anyconnect Secure Mobility Client, Network Access Module, wired PEAP

Hello there,
I am testing AnyConnect Secure Mobility Client, Network Access Module as supplicant with PEAP authentication for wired network users. With default configuration it is working well. With default configuration it is Trusting any Root CA certificates installed on the OS. Do you know how to configure NAM that it will validate ACS certificate with specific Root CA Certificate ?
In Network Access Module profile editor it has two options about Certificates:
One is Certificate Trusted Authority which has two options by its self first is too trust any Root CA certificate that is installed on OS, and second is to import Root CA certificate in Profile. Potentially Second option can help in my case, I can manually import Root CA certificates in each profile. But I think it will be hard to update Root CA certificates in future in that way.
Second is Certificate Trusted Server Rules, this option have matching capability by certificate Common Name. For what can be used this option ?

Normally the way it works is that you set up your Enterprise Root CA, and then have it issue a certifcate for the AAA server (ie ACS, ISE, etc). You then install this certificate on the AAA server and (in an Active Directory environment) add the Root CA certificate to the client systems local certificate store. What that means is that any certificates (such as the one installed on the AAA server) that are presented to the client that are signed by the root are automatically trusted.
Server validation is an extra step in terms of proving the identity of the AAA server to the authenticating client. As such, when you build the policy in the NAM editor, it would look similar to the image below:
I like to use the CN (Common Name) as the match criteria and build my CA issuance policy to always include the FQDN in the certificate for identity purposes.
Hope this helps!

AnyConnect + Network Access Manager (NAM) + Certificate

Hello,
I want to use Network Access Manager with Anyconnect.
I configured a WiFi network with EAP-TLS authentication.
The certificate used for EAP-TLS has the following EKU:
- clientAuth (1.3.6.1.5.5.7.3.2)
- emailProtection (1.3.6.1.5.5.7.3.4)
- msSmartcardLogin (1.3.6.1.4.1.311.20.2.2)
It works with Microsoft Wireless Zero Configuration.
With NAM, I have this error "No valid certificates available. Please insert a smart card or install a valid certificate"
If I remove msSmartcardLogin EKU, it works with NAM.
I can't remove this EKU because Smart card logon is used.
Why msSmartcardLogin EKU generates this error?
How can I resolve it?
Thanks a lot for your support.
Patrick

Hi,
I am having the same issue, but have noticed that every now and then the NAM will fail to detect the certificate 3 times then suddently in the NAM event log there will be a message that saying "“Enumerating certificate store 'user personal'.” and it would retrieve the local certificate for authentication.
Has anyone else experienced this problem? and knows the fix?
Regards,
JZ
anyconnect fails to detect the local certificate store about 3 time before “Enumerating certificate store 'user personal'.” And retrieves the local user certificate for authentication.

On my new iMac, mail has no sound after waking from sleep. If I select do not wake for network access in general preferences, the problem does not occur. Anyone have an idea on how to fix this?

On my new iMac, mail has no sound after waking from sleep. If I select do not wake for network access in general preferences, the problem does not occur. Anyone have an idea on how to fix this? Thanks --

Same here on an older iMac since Lion. Thanks for the uncheck wake for network access tip though, it doesn't do it either in that case, I will leave it that way.

SCCM 2012 Network Access Account password problem

Hello Everyone,
I got a problem with the Network Access Account on SCCM 2012. I didn't have any problem previously and can deploy OS successfully. The problem started last week when I tried to deploy an OS. It gave me a error on Task Sequence then I searched for the error
and found that its related with the Network Access Account. On SCCM Config Manager I checked the Network Access Account and found that I had the wrong password. But the bigger problem starts here: on configManager Administration/Security/accounts window
I open my NAS properties and on the verify window tried to reach a simple network share and it says the password is wrong, then I change the password and tried to verify one more time and it successfully reaches the share, I simply click apply and
OK as usual but when I open the properties window I always see the old password stays there. I tried to change the password maybe 100 time but I didn't work. My NAS is a normal domain account with Domain Users permissions, I ve already
checked the password, account and password never expires options, they are all rightly configured. I also tried to make a new account to use as a NAS, then I set it on SCCM as a NAS but the result is always the same. Accounts
have wrong password and I cant change and save it. Actually I can change till I close the properties window then its all gone , reset to old wrong password. Please help me with that, I am googling it like 2 days and found that the same thing happened
to 2 other people, but there is no solution...

That workaround seems to work. Only verify when you first type the password and get the success/confirmation message. Once you hit OK to save the password, something happens to it (probably encrypts the password entered). If you open the account
settings again, I assume SCCM takes the password from the database or task sequence in it's encrypted form and presents that in the text boxes. Clicking OK will save the password again, but because it is presented in it's encrypted form, will re-encrypt
this as a new password and effectively change what you originally entered as the password. Again, I'm just assuming this based on what I observed. If it's true, then definately a bug.
I think this is pretty correct. This whole (non?)-issue was a massive red-herring for me. I spent a week trying to understand what was wrong, but eventually discovered the issue was a couple of steps down the line. SCCM errors on the surface level are pretty
consistently confusing. 9 times out of ten, I have been lead astray by them. Crack open your log files, your real problems will be in there.

Just updated my i-Phone 6 from 8.0 to 8.02 (not tried 8.01). Now I have all the problem they describe with 8.01 (lost ID Touch, no cell network access). So the 8.02 did create a problem I did not have. What to do?

just updated my i-Phone 6 from 8.0 to 8.02 (did not try 8.01). Now I have all the problem they describe with 8.01 (lost ID Touch, no cell network access). So the 8.02 did create a problem I did not have. What to do?

Basics have always been, and continue to remain: restart, reset, restore from backup, restore as new device.

Cisco's AnyConnect Network Access Manager (NAM)

Hi dears,
I configurate EAP_FAST in Cisco ISE and want wired users authenticate from ISE. I install Network Access Manager Profile Editor and Cisco Anyconnect Security Mobility Client on PC. I configure Network Access Manager when i want to save as that I did not see the . \newConfigFiles folder. Then I did that: Organize’, ‘Folder and Search Options’, ‘Show hidden files, folders, and drives. but in this case i did see the network access manager folder.
I need a to install Cisco’s AnyConnect Network Access Manager (NAM) on PC. HOW I get this soft? I have a smartnet for ISE.
Which email address(to cisco) i must be write to get this soft?
Thanks.

You can download the Network Access Manager module from CCO. This link should work if you have a CCO account.
http://software.cisco.com/download/release.html?mdfid=283000185&softwareid=282364313&release=3.1.05160&relind=AVAILABLE&rellifecycle=&reltype=latest&i=rs
The file name will be similar to anyconnect-win-3.1.05160-pre-deploy-k9.iso. Just unzip the ISO with 7zip or Winrar and you will see the NAM msi file anyconnect-nam-win-3.1.05149-k9.msi.

Fix many web access problems with IFS 9.0.1 on Solaris (and other OS's)...

When the installation is done according to the documentation,
web access does not work because the scripts that add entries to
the jserv.properties file add duplicate references to
wrapper.env and wrapper.classpath. Look at the jserv.properties
file below and look at the remarked-out (#) lines of the
duplicate references. For example, look at the references to the
wrapper.env=LD_LIBRARY_PATH
Oracle, please note this bug so the web access problems are
minimized when the product is intstalled.
Thank you,
William T.
# Apache JServ Configuration
File #
################################ W A R N I N G
# Unlike normal Java properties, JServ configurations have some
important
# extensions:
# 1) commas are used as token separators
# 2) multiple definitions of the same key are concatenated in
a
# comma separated list.
# Execution parameters
# The Java Virtual Machine interpreter.
# Syntax: wrapper.bin=[filename] (String)
# Note: specify a full path if the interpreter is not visible in
your path.
wrapper.bin=/d3/Apache/jdk/bin/java
# Arguments passed to Java interpreter (optional)
# Syntax: wrapper.bin.parameters=[parameters] (String)
# Default: NONE
wrapper.bin.parameters=-Xms64m
wrapper.bin.parameters=-Xmx128m
# Apache JServ entry point class (should not be changed)
# Syntax: wrapper.class=[classname] (String)
# Default: "org.apache.jserv.JServ"
# Arguments passed to main class after the properties filename
(not used)
# Syntax: wrapper.class.parameters=[parameters] (String)
# Default: NONE
# Note: currently not used
# PATH environment value passed to the JVM
# Syntax: wrapper.path=[path] (String)
# Default: "/bin:/usr/bin:/usr/local/bin" for Unix systems
# "c:\(windows-dir);c:\(windows-system-dir)" for Win32
systems
# Notes: if more than one line is supplied these will be
concatenated using
# ":" or ";" (depending wether Unix or Win32) characters
# Under Win32 (windows-dir) and (windows-system-dir) will
be
# automatically evaluated to match your system
requirements
# CLASSPATH environment value passed to the JVM
# Syntax: wrapper.classpath=[path] (String)
# Default: NONE (Sun's JDK/JRE already have a default classpath)
# Note: if more than one line is supplied these will be
concatenated using
# ":" or ";" (depending wether Unix or Win32) characters.
JVM must be
# able to find JSDK and JServ classes and any utility
classes used by
# your servlets.
# Note: the classes you want to be automatically reloaded upon
modification
# MUST NOT be in this classpath or the classpath of the
shell
# you start the Apache from.
wrapper.classpath=/d3/Apache/jdk/lib/tools.jar
wrapper.classpath=/d3/Apache/Jserv/libexec/ApacheJServ.jar
wrapper.classpath=/d3/Apache/Jsdk/lib/jsdk.jar
# An environment name with value passed to the JVM
# Syntax: wrapper.env=[name]=[value] (String)
# Default: NONE on Unix Systems
# SystemDrive and SystemRoot with appropriate values on
Win32 systems
wrapper.env=PATH=/d3/bin
# An environment name with value copied from caller to Java
Virtual Machine
# Syntax: wrapper.env.copy=[name] (String)
# Default: NONE
# Uncomment the following lines to set the default locale and
NLS_LANG
# setting based on the environment variables.
# wrapper.env.copy=LANG
# wrapper.env.copy=NLS_LANG
# Copies all environment from caller to Java Virtual Machine
# Syntax: wrapper.env.copyall=true (boolean)
# Default: false
# Protocol used for signal handling
# Syntax: wrapper.protocol=[name] (String)
# Default: ajpv12
# General parameters
# Set the default IP address or hostname Apache JServ binds (or
listens) to.
# If you have a machine with multiple IP addresses, this address
# will be the one used. If you set the value to localhost, it
# will be resolved to the IP address configured for the locahost
# on your system (generally this is 127.0.0.1). This feature is
so
# that one can have multiple instances of Apache JServ listening
on
# the same port number, but different IP addresses on the same
machine.
# Use bindaddress=* only if you know exactly what you are doing
here,
# as it could let JServ wide open to the internet.
# You must understand that JServ has to answer only to Apache,
and should not
# be reachable by nobody but mod_jserv. So localhost is usually a
# good option. The second best choice would be an internal
network address
# (protected by a firewall) if JServ is running on another
machine than Apache.
# Ask your network admin.
# "*" may be used on boxes where some of the clients get
connected using
# "localhost"and others using another IP addr.
# Syntax: bindaddress=[ipaddress] or [localhost] or [*]
# Default: localhost
bindaddress=localhost
# Set the port Apache JServ listens to.
# Syntax: port=[1024,65535] (int)
# Default: 8007
port=8007
# Servlet Zones parameters
# List of servlet zones Apache JServ manages
# Syntax: zones=[servlet zone],[servlet zone]... (Comma
separated list of String)
# Default: NONE
zones=root
# Configuration file for each servlet zone (one per servlet zone)
# Syntax: [servlet zone name as on the zones list].properties=
[full path to configFile]
(String)
# Default: NONE
# Note: if the file could not be opened, try using absolute
paths.
root.properties=/d3/Apache/Jserv/etc/zone.properties
# Thread Pool parameters
# Enables or disables the use of the thread pool.
# Syntax: pool=true (boolean)
# Default: false
# WARNING: the pool has not been extensively tested and may
generate
deadlocks.
# For this reason, we advise against using this code in
production environments.
pool=false
# Indicates the number of idle threads that the pool may contain.
# Syntax: pool.capacity=(int)>0
# Default: 10
# NOTE: depending on your system load, this number should be low
for contantly
# loaded servers and should be increased depending on load
bursts.
pool.capacity=10
# Indicates the pool controller that should be used to control
the
# level of the recycled threads.
# Syntax: pool.controller=[full class of controller] (String)
# Default: org.apache.java.recycle.DefaultController
# NOTE: it is safe to leave this unchanged unless special
recycle behavior
# is needed. Look at the "org.apache.java.recycle" package
javadocs for more
# info on other pool controllers and their behavior.
pool.controller=org.apache.java.recycle.DefaultController
# Security parameters
# Enable/disable the execution of org.apache.jserv.JServ as a
servlet.
# This is disabled by default because it may give informations
that should
# be restricted.
# Note that the execution of Apache JServ as a servlet is
filtered by the web
# server modules by default so that both sides should be enabled
to let this
# service work.
# This service is useful for installation and configuration
since it gives
# feedback about the exact configurations Apache JServ is using,
but it should
# be disabled when both installation and configuration processes
are done.
# Syntax: security.selfservlet=true (boolean)
# Default: false
# WARNING: disable this in a production environment since may
give reserved
# information to untrusted users.
security.selfservlet=true
# Set the maximum number of socket connections Apache JServ may
handle
# simultaneously. Make sure your operating environment has
enough file
# descriptors to allow this number.
# Syntax: security.maxConnections=(int)>1
# Default: 50
security.maxConnections=50
# Backlog setting for very fine performance tunning of JServ.
# Unless you are familiar to sockets leave this value commented
out.
# security.backlog=5
# List of IP addresses allowed to connect to Apache JServ. This
is a first
# security filtering to reject possibly unsecure connections and
avoid the
# overhead of connection authentication.
# <warning>
# (please don't use the following one unless you know what you
are doing :
# security.allowedAddresses=DISABLED
# allows connections on JServ'port from entire internet.)
# You do need only to allow YOUR Apache to talk to JServ.
# </warning>
# Default: 127.0.0.1
# Syntax: security.allowedAddresses=[IP address],[IP Address]...
(Comma
separated list of IP addresses)
#security.allowedAddresses=127.0.0.1
# Enable/disable connection authentication.
# NOTE: unauthenticated connections are a little faster since
authentication
# handshake is not performed at connection creation.
# WARNING: authentication is disabled by default because we
believe that
# connection restriction from all IP addresses but localhost
reduces your
# time to get Apache JServ to run. If you allow other addresses
to connect and
# you don't trust it, you should enable authentication to
prevent untrusted
# execution of your servlets. Beware: if authentication is
disabled and the
# IP address is allowed, everyone on that machine can execute
your servlets!
# Syntax: security.authentication=[true,false] (boolean)
# Default: true
security.authentication=false
# Authentication secret key.
# The secret key is passed as a file that must be kept secure
and must
# be exactly the same of those used by clients to authenticate
themselves.
# Syntax: security.secretKey=[secret key path and filename]
(String)
# Default: NONE
# Note: if the file could not be opened, try using absolute
paths.
#security.secretKey=./etc/jserv.secret.key
# Length of the randomly generated challenge string (in bytes)
used to
# authenticate connections. 5 is the lowest possible choice to
force a safe
# level of security and reduce connection creation overhead.
# Syntax: security.challengeSize=(int)>5
# Default: 5
#security.challengeSize=5
# Logging parameters
# Enable/disable Apache JServ logging.
# WARNING: logging is a very expensive operation in terms of
performance. You
# should reduced the generated log to a minumum or even disable
it if fast
# execution is an issue. Note that if all log channels (see
below) are
# enabled, the log may become really big since each servlet
request may
# generate many Kb of log. Some log channels are mainly for
debugging
# purposes and should be disabled in a production environment.
# Syntax: log=[true,false] (boolean)
# Default: true
log=true
# Set the name of the trace/log file. To avoid possible
confusion about
# the location of this file, an absolute pathname is recommended.
# This log file is different than the log file that is in the
# jserv.conf file. This is the log file for the Java portion of
Apache
# JServ.
# On Unix, this file must have write permissions by the owner of
the JVM
# process. In other words, if you are running Apache JServ in
manual mode
# and Apache is running as user nobody, then the file must have
its
# permissions set so that that user can write to it.
# Syntax: log.file=[log path and filename] (String)
# Default: NONE
# Note: if the file could not be opened, try using absolute
paths.
log.file=/d3/Apache/Jserv/logs/jserv.log
# Enable the timestamp before the log message
# Syntax: log.timestamp=[true,false] (boolean)
# Default: true
log.timestamp=true
# Use the given string as a data format
# (see java.text.SimpleDateFormat for the list of options)
# Syntax: log.dateFormat=(String)
# Default: [dd/MM/yyyy HH:mm:ss:SSS zz]
log.dateFormat=[dd/MM/yyyy HH:mm:ss:SSS zz]
# Since all the messages logged are processed by a thread
running with
# minimum priority, it's of vital importance that this thread
gets a chance
# to run once in a while. If it doesn't, the log queue overflow
occurs,
# usually resulting in the OutOfMemoryError.
# To prevent this from happening, two parameters are used:
log.queue.maxage
# and log.queue.maxsize. The former defines the maximum time for
the logged
# message to stay in the queue, the latter defines maximum
number of
# messages in the queue.
# If one of those conditions becomes true (age > maxage || size
maxsize),# the log message stating that fact is generated and the log
queue is
# flushed in the separate thread.
# If you ever see such a message, either your system doesn't
live up to its
# expectations or you have a runaway loop (probably, but not
necessarily,
# generating a lot of log messages).
# WARNING: Default values are lousy, you probably want to tweak
them and
# report the results back to the development team.
# Syntax: log.queue.maxage = [milliseconds]
# Default: 5000
log.queue.maxage = 5000
# Syntax: log.queue.maxsize = [integer]
# Default: 1000
log.queue.maxsize = 1000
# Enable/disable logging the channel name
# Default: false
# log.channel=false
# Enable/disable channels, each logging different actions.
# Syntax: log.channel.[channel name]=[true,false] (boolean)
# Default: false
# Info channel - quite a lot of informational messages
# hopefully you don't need them under normal circumstances
# log.channel.info=true
# Servlets exception, i.e. exception caught during
# servlet.service() processing are monitored here
# you probably want to have this one switched on
log.channel.servletException=true
# JServ exception, caught internally in jserv
# we suggest to leave it on
log.channel.jservException=true
# Warning channel, it catches all the important
# messages that don't cause JServ to stop, leave it on
log.channel.warning=true
# Servlet log
# All messages logged by servlets. Probably you want
# this one to be switched on.
log.channel.servletLog=true
# Critical errors
# Messages produced by critical events causing jserv to stop
log.channel.critical=true
# Debug channel
# Only for internal debugging purposes
# log.channel.debug=true
#wrapper.classpath=/d3/ord/jlib/ordim.zip
#wrapper.classpath=/d3/ord/jlib/ordhttp.zip
# Oracle XSQL Servlet
wrapper.classpath=/d3/lib/oraclexsql.jar
# Oracle JDBC
wrapper.classpath=/d3/jdbc/lib/classes12.zip
# Oracle XML Parser V2 (with XSLT Engine)
wrapper.classpath=/d3/lib/xmlparserv2.jar
# Oracle XML SQL Components for Java
wrapper.classpath=/d3/rdbms/jlib/xsu12.jar
# XSQLConfig.xml File location
wrapper.classpath=/d3/xdk/admin
# Oracle BC4J
wrapper.classpath=/d3/ord/jlib/ordim.zip
wrapper.classpath=/d3/ord/jlib/ordvir.zip
wrapper.classpath=/d3/ord/jlib/ordhttp.zip
wrapper.classpath=/d3/BC4J/lib/jndi.jar
wrapper.classpath=/d3/BC4J/lib/jbomt.zip
wrapper.classpath=/d3/BC4J/lib/javax_ejb.zip
wrapper.classpath=/d3/BC4J/lib/jdev-rt.jar
wrapper.classpath=/d3/BC4J/lib/jbohtml.zip
wrapper.classpath=/d3/BC4J/lib/jboremote.zip
wrapper.classpath=/d3/BC4J/lib/jdev-cm.jar
wrapper.classpath=/d3/BC4J/lib/jbodomorcl.zip
wrapper.classpath=/d3/BC4J/lib/jboimdomains.zip
wrapper.classpath=/d3/BC4J/lib/collections.jar
wrapper.classpath=/d3/Apache/Apache/htdocs/onlineorders_html
#wrapper.classpath=/d3/Apache/Apache/htdocs/OnlineOrders_html/Onl
ineOrders.jar
# The following classpath entries are necessary for EJBs to run
in IAS or DB when
present
wrapper.classpath=/d3/lib/aurora_client.jar
wrapper.classpath=/d3/lib/vbjorb.jar
wrapper.classpath=/d3/lib/vbjapp.jar
# Oracle Servlet
wrapper.classpath=/d3/lib/servlet.jar
# Oracle Java Server Pages
wrapper.classpath=/d3/jsp/lib/ojsp.jar
# Oracle Util
wrapper.classpath=/d3/jsp/lib/ojsputil.jar
# Oracle Java SQL
wrapper.classpath=/d3/sqlj/lib/translator.zip
# Oracle JDBC
#wrapper.classpath=/d3/jdbc/lib/classes12.zip
# SQLJ runtime
wrapper.classpath=/d3/sqlj/lib/runtime12.zip
# Oracle Messaging
wrapper.classpath=/d3/rdbms/jlib/aqapi.jar
wrapper.classpath=/d3/rdbms/jlib/jmscommon.jar
# OJSP environment settings
#wrapper.env=ORACLE_HOME=/d3
# The next line should be modified to reflect the value of the
SID for your
webserver.
#wrapper.env=ORACLE_SID=cmpdb
#wrapper.env=LD_LIBRARY_PATH=/d3/lib
## Enable the flag below if you are using jdk 1.2.2_05a or above
#wrapper.env=JAVA_COMPILER=NONE
# Advanced Queuing - AQXML
wrapper.classpath=/d3/rdbms/jlib/aqxml.jar
#wrapper.classpath=/d3/rdbms/jlib/xsu12.jar
#wrapper.classpath=/d3/lib/xmlparserv2.jar
wrapper.classpath=/d3/lib/xschema.jar
#wrapper.classpath=/d3/jlib/jndi.jar
wrapper.classpath=/d3/jlib/jta.jar
oemreporting.properties=/d3/Apache/Jserv/oemreporting/oemreportin
g.properties
zones = root, oemreporting
wrapper.classpath=/d3/jlib/share-opt-1_1_9.zip
wrapper.classpath=/d3/jlib/caboshare-opt-1_0_3.zip
wrapper.classpath=/d3/jlib/marlin-opt-1_0_7.zip
wrapper.classpath=/d3/jlib/tecate-opt-1_0_4.zip
wrapper.classpath=/d3/jlib/ocelot-opt-1_0_2.zip
wrapper.classpath=/d3/jlib/regexp.jar
wrapper.classpath=/d3/jlib/sax2.jar
#wrapper.classpath=/d3/jlib/servlet.jar
wrapper.bin.parameters= -DORACLE_HOME=/d3
#wrapper.env=LD_LIBRARY_PATH=/d3/lib32
wrapper.env.copy=DISPLAY
wrapper.bin.parameters=-DORACLE_HOME=/d3
#wrapper.classpath=/d3/lib/vbjorb.jar
#wrapper.classpath=/d3/lib/vbjapp.jar
wrapper.classpath=/d3/classes/classesFromIDLVisi
wrapper.classpath=/d3/jlib/swingall-1_1_1.jar
wrapper.classpath=/d3/jlib/ewtcompat3_3_15.jar
wrapper.classpath=/d3/jlib/ewt-3_3_18.jar
wrapper.classpath=/d3/jlib/share-1_1_9.jar
wrapper.classpath=/d3/jlib/help-3_2_9.jar
wrapper.classpath=/d3/jlib/ice-5_06_3.jar
wrapper.classpath=/d3/jdbc/lib/classes111.zip
wrapper.classpath=/d3/classes
wrapper.classpath=/d3/jlib/oembase-9_0_1.jar
wrapper.classpath=/d3/jlib/oemtools-9_0_1.jar
wrapper.classpath=/d3/jlib
wrapper.classpath=/d3/jlib/javax-ssl-1_1.jar
wrapper.classpath=/d3/jlib/jssl-1_1.jar
wrapper.classpath=/d3/jlib/netcfg.jar
wrapper.classpath=/d3/jlib/dbui-2_1_2.jar
#wrapper.classpath=/d3/lib/aurora_client.jar
#wrapper.classpath=/d3/lib/xmlparserv2.jar
wrapper.classpath=/d3/network/jlib/netmgrm.jar
wrapper.classpath=/d3/network/jlib/netmgr.jar
wrapper.classpath=/d3/network/tools
wrapper.classpath=/d3/jlib/kodiak-1_2_1.jar
wrapper.classpath=/d3/sysman/jlib/netchart360.jar
wrapper.classpath=/d3/jlib/pfjbean.jar
wrapper.env=SHLIB_PATH=/d3/lib32
wrapper.env=LIBPATH=/d3/lib32
wrapper.classpath=/d3/ultrasearch/lib/isearch_midtier.jar
wrapper.classpath=/d3/ultrasearch/lib/isearch_query.jar
wrapper.classpath=/d3/ultrasearch/lib/jgl3.1.0.jar
wrapper.classpath=/d3/lib/mail.jar
wrapper.classpath=/d3/lib/activation.jar
wrapper.classpath=/d3/ultrasearch/jsp/admin/config
# Additions for iFS
## DO NOT REMOVE OR ALTER THE FOLLOWING LINE ....
# iFS true
# Uncomment if you want to use the same Jserv as other
applications
wrapper.classpath=/d3/9ifs/custom_classes
wrapper.classpath=/d3/9ifs/settings
wrapper.classpath=/d3/9ifs/lib/adk.jar
wrapper.classpath=/d3/9ifs/lib/email.jar
wrapper.classpath=/d3/9ifs/lib/http.jar
wrapper.classpath=/d3/9ifs/lib/release.jar
wrapper.classpath=/d3/9ifs/lib/repos.jar
wrapper.classpath=/d3/9ifs/lib/utils.jar
wrapper.classpath=/d3/9ifs/lib/webui.jar
wrapper.classpath=/d3/9ifs/lib/provider.jar
wrapper.classpath=/d3/jlib/javax-ssl-1_2.jar
wrapper.classpath=/d3/jlib/jssl-1_2.jar
wrapper.env=ORACLE_HOME=/d3
wrapper.env=ORACLE_SID=cmpdb
wrapper.env=LD_LIBRARY_PATH=/d3/lib:/d3/ctx/lib:/d3/lib32
wrapper.env=NLS_LANG=.US7ASCII
## Additions for the iFS zone
# Uncomment if you want to use the same Jserv as other
applications
zones=ifs
ifs.properties=/d3/Apache/Jserv/etc/ifs.properties
# End iFS section

About your home page; Manually set up Firefox with the window(s) and tab(s)
the way you want them to be. Then;
'''''Firefox Options > General > Homepage'''''.
Press the button labeled ''''Use Current'''.'
=====================================
Open a new window or tab. In the address bar, type '''''about:config'''''.
If a warning screen comes up, press the '''''Be Careful''''' button.
This is where Firefox finds information it needs to run.
At the top of the screen is a search bar. Enter '''''browser.newtab.url'''''
and press enter. '''''browser.newtab.url'''''
tells Firefox what to show when a new tab is opened.
If you want, right click and select '''''Modify'''''. You can change the
setting to; about:home (Firefox default home page), 
about:newtab (shows the sites most visited), 
about:blank (a blank page), 
or you can enter any web page you want. 
The same instructions are used for the new window setting, listed as
'''''browser.startup.homepage'''''.

SCCM 2012 R2 - Distribution Point untrusted domain - Not acknowledging Network Access Account (FYI)

Hello!
Scenario
Built a single primary site server in one domain with multiple distribution points. All site servers are member of this one site.
The distribution points in the primary site servers' domain function as expected. The distribution point deployed to an untrusted domain does not. The primary site server can see all objects in the domain, publishes successfully, and CCM client on the
DP in the untrusted domain knows its part of the site, knows its AD site (according to locationservices.log). The DP role is installed properly, logs are populating, queries are being made for application lists and updates. nfortuantely authentication
errors indicate that this software can'tbe downloaded.
In essence the DP in the untrusted domain can't pull down content from the primary site server. The role uses BITS to download content from IIS on the primary site server, but the requests each throw a 401 error. Unauthorised. This should be an easy fix.
Create a Network Access Account in the primary site server's domain, assign it to the site (Software Distribution setting), wait for the DP to pick up the setting and watch it retrieve its content. The DP in the untrusted domain is configured as a Pull DP,
implying it has to use a Network Access Account to download content. It knows the content is available and makes every effort to download it.
Problem
The DP in the untrusted domain doesn't know a Network Access Account (NAA) has been defined for the site.
The account does exist, created in the primary site server's domain and assigned to the site. Its not a password issue. IIS has not been set for Anonymous access as this isn't needed - the NAA should provide the credentials it requires to pull down content.
A manual check using the URL of the package confirms the package is accessible from the DP when using the NAA's credentials. I've allowed enough time (i think) for the DP to acknowledge the NAA. For fun the DP role was removed, and the CCM agent removed. Both
were reinstalled. A fresh install didn't detect the NAA.
Solution
After some soul searching and a little frustration, it came down to this: A Pull DP always uses the Network Access Account. If the DP can't find a Network Access account it will fail to pull down content. This is undisputed. Found an article that states
the Pull DP always uses the CCM client configuration to do its dirty work. At that point the CCM client was checked. It had the classic problem of only displaying two Actions - Machine Policy Retrieval & Evaluation Cycle, User policy Retrieval & Evaluation
Cycle. Most components were installed but not enabled. This is fairly common. Looked at the console, found the device, added the Approval column. Turns out it wasn't auto-approved. Reason being that the client is in an untrusted domain and clients in untrusted
domains aren't approved automatically (by default).
In this case something as simple as an Approving the client fixed these issues.
The DataTransferService.log highlights the issue:
<![LOG[CDTSJob::JobError: DTS Job ID='{17E0B672-F699-434D-B063-87CC2ACF715C}' BITS Job ID='{38B81ADE-55B5-4BD7-A881-DBFF13943EDE}' ErrorCode=0x80190191]LOG]!><time="18:25:54.264+00" date="02-19-2015" component="DataTransferService"
context="" type="1" thread="3136" file="dtsjob.cpp:3501">
<![LOG[CDTSJob::JobError: DTS Job ID='{17E0B672-F699-434D-B063-87CC2ACF715C}' URL='http://PRIMARYSERVER.A.B.COM:80/SMS_DP_SMSPKG$/5af1680e-4a14-4dc5-8a60-bda7370e6d68'
ProtType=1]LOG]!><time="18:25:54.264+00" date="02-19-2015" component="DataTransferService" context="" type="1" thread="3136" file="dtsjob.cpp:3504">
<![LOG[Authentication required by the proxy, DTS Job ID='{17E0B672-F699-434D-B063-87CC2ACF715C}' BITS Job ID='{38B81ADE-55B5-4BD7-A881-DBFF13943EDE}'.]LOG]!><time="18:25:54.264+00" date="02-19-2015" component="DataTransferService"
context="" type="3" thread="3136" file="dtsjob.cpp:3513">
<![LOG[DTSJob {8814E9A1-3D26-4089-83CF-3C7D17BCEC6E} in state 'Cancelled'.]LOG]!><time="18:25:54.264+00" date="02-19-2015" component="DataTransferService" context="" type="1" thread="3688"
file="dtsjob.h:166">
<![LOG[DTS job {17E0B672-F699-434D-B063-87CC2ACF715C} BITS job
{38B81ADE-55B5-4BD7-A881-DBFF13943EDE} encountered Access Denied error during download. Will retry using Network Access Account.]LOG]!><time="18:25:54.264+00" date="02-19-2015" component="DataTransferService"
context="" type="2" thread="3136" file="dtsjob.cpp:3652">
<![LOG[DTSJob {8814E9A1-3D26-4089-83CF-3C7D17BCEC6E} cancelled by client.]LOG]!><time="18:25:54.280+00" date="02-19-2015" component="DataTransferService" context="" type="1" thread="3688"
file="dtsjob.cpp:3205">
<![LOG[No network access account info found.]LOG]!><time="18:25:54.327+00" date="02-19-2015" component="DataTransferService" context="" type="1"
thread="3136" file="netaccessaccount.cpp:288">
<![LOG[The network access account is not defined.]LOG]!><time="18:25:54.327+00" date="02-19-2015" component="DataTransferService" context=""
type="1" thread="3136" file="netaccessaccount.cpp:858">
<![LOG[DTSJob {17E0B672-F699-434D-B063-87CC2ACF715C} encountered error setting BITS job to use Network Access Account
(0x00000000).]LOG]!><time="18:25:54.327+00" date="02-19-2015" component="DataTransferService" context="" type="3" thread="3136" file="dtsjob.cpp:1885">
The IIS server logs u_ex150219.log captures the request:
2015-02-19 123.11.12.13 GET /SMS_DP_SMSPKG$/5af1680e-4a14-4dc5-8a60-bda7370e6d68/sccm /windows6.1-kb3021917-x64.cab 80 - 9.10.11.12 Microsoft+BITS/7.7 -
401 2 5 1509 2
2015-02-19 123.11.12.13 GET /SMS_DP_SMSPKG$/5af1680e-4a14-4dc5-8a60-bda7370e6d68/sccm /windows6.1-kb3021917-x64.cab 80 - 9.10.11.12 Microsoft+BITS/7.7 -
401 1 3221225581 1509 4
2015-02-19 123.11.12.13 GET /SMS_DP_SMSPKG$/5af1680e-4a14-4dc5-8a60-bda7370e6d68/sccm /windows6.1-kb3021917-x64.cab 80 - 9.10.11.12 Microsoft+BITS/7.7 -
401 1 3221225581 1509 3
2 x Domains: DomainA and DomainX
- Single domain forests
- No trusts between domains/forests
DomainA\PRIMARYSERVER
- Primary Site Server, MP, DP, IIS, all roles
DomainX\DP1
- Distribution Point, IIS, etc
- CCM client installed

Based on the above, you are using a PullDP. If so, have you installed the client agent on this system? The client agent is required on PullDPs in untrusted domains so that they can acquire the NAA.
Jason | http://blog.configmgrftw.com | @jasonsandys

AnyConnect users cannot access internet

When AnyConnect users try to connect to the internet it will not let them out. I've included a copy of my config below. Also, I have a 5505 with base license but the AnyConnect for mobile is disabled. I got what seems to be a demo license from Cisco for 91 days. I thought that the base license came with AnyConnect for 2 devices. Why is the AnyConnect for mobile disabled by default?
ASA Version 8.4(2)
hostname ASA5505
domain-name <removed>
enable password <removed>
passwd <removed>
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 10.10.10.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
banner motd
banner motd +...................................................-+
banner motd | |
banner motd | *** Unauthorized Use or Access Prohibited *** |
banner motd | |
banner motd | For Authorized Official Use Only |
banner motd | You must have explicit permission to access or |
banner motd | configure this device. All activities performed |
banner motd | on this device will be logged, and violations of |
banner motd | this policy may result in disciplinary action, and |
banner motd | may be reported to law enforcement authorities. |
banner motd | |
banner motd | There is no right to privacy on this device. |
banner motd | |
banner motd +...................................................-+
ftp mode passive
clock timezone CST -6
clock summer-time CDT recurring
dns domain-lookup inside
dns domain-lookup outside
dns server-group DefaultDNS
name-server 68.105.28.12
name-server 68.105.29.12
domain-name ok.cox.net
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object network INSIDE-HOSTS
subnet 10.10.10.0 255.255.255.0
object network AnyConnect-INET
subnet 192.168.10.0 255.255.255.0
access-list Internet_IN extended permit icmp any interface outside echo-reply
access-list Internet_IN extended permit icmp any interface outside
pager lines 24
logging enable
logging timestamp
logging buffered informational
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool vpnpool 192.168.10.1-192.168.10.254 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
icmp permit any inside
icmp permit any echo-reply inside
icmp permit any echo-reply outside
icmp permit any outside
no asdm history enable
arp timeout 14400
nat (inside,outside) source dynamic AnyConnect-INET interface
object network INSIDE-HOSTS
nat (inside,outside) dynamic interface
access-group Internet_IN in interface outside
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication http console LOCAL
aaa authentication ssh console LOCAL
http server enable
http 10.10.10.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 70
authentication crack
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 110
authentication rsa-sig
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 10.10.10.0 255.255.255.0 inside
ssh timeout 5
console timeout 0
dhcpd auto_config outside
dhcpd update dns both
dhcpd address 10.10.10.25-10.10.10.50 inside
dhcpd dns 68.105.28.12 68.105.29.12 interface inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
enable outside
anyconnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
anyconnect enable
tunnel-group-list enable
group-policy "Client Group" internal
group-policy "Client Group" attributes
wins-server none
dns-server value <removed>
vpn-tunnel-protocol ikev1 ikev2 ssl-client ssl-clientless
split-tunnel-policy tunnelall
default-domain value <removed>
split-dns value <removed>
webvpn
anyconnect ssl rekey time none
anyconnect ssl rekey method ssl
anyconnect ask none default anyconnect
username <removed> password <removed> privilege 15
username <removed> attributes
webvpn
anyconnect ask none default anyconnect
username <removed> password <removed> privilege 15
tunnel-group TunnelGroup1 type remote-access
tunnel-group TunnelGroup1 general-attributes
address-pool vpnpool
default-group-policy "Client Group"
tunnel-group TunnelGroup1 webvpn-attributes
group-alias ssl_group_users enable
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect ip-options
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:943c1846a54a525f95905e6ebe313048
: end

I found part of my problem. There wasn't nat (outside,outside) dynamic interface applyed to the AnyConnect object network. The other half of my question is still a mystery. How come the AnyConnect for Mobile is off by default on a base license when it's supposed to come with 2 AnyConnect mobile licenses installed?

AnyConnect Trusted Network Access Problem

Similar Messages

Maybe you are looking for