AP Ex access works for one device connection, 2nd device gets booted off

I have a brand new 1 TB Time Capsule AirPort Extreme set up with PPPoe, and an AT&T Motorola 2210-02 modem set up PPP ("Private IP for LAN device").
screen shot:
http://courses.wccnet.edu/~klund/ss/sstimecapsulesettings.png
(This was the only way I could get it to work after trying several other configurations.) My MacBook Pro AirPort is able to connect; however we have an LG Blu-ray player with wireless access and when I turn that on it kicks the laptop off.
screen shot:
http://courses.wccnet.edu/~klund/ss/ss_kickedoff.png
In addition, I'm not able to connect with my iPod touch after the password is accepted.
I had this exact problem with the older AirPort (UFO looking one) and was told by several store people that it probably just crapped out. (It had been working fine with more than one device at our previous residence - when we moved the only new variable was the Motorola modem.)
I couldn't find other posts like this, I hope this isn't redundant.

a2kirsten wrote:
I reset the modem and the TC and tried several configurations, i.e. modem in bridge/TC PPPoE; modem with PPP/TC in bridge; I also tried the TC with "Share a Public IP address" and got the error "+The DHCP range you have entered conflicts with the WAN IP address of your AirPort wireless device+".
When I did the TC in Bridge mode (+ modem PPP) I got a Double NAT error and as soon as the setup was finished I got the kickoff message again.
http://courses.wccnet.edu/~klund/ss/ss_modemPPP-TCbridge.png
That screen shot shows why you're seeing those messages about "another device on the network ..." The Time Capsule is using that same IP address.
The interface for the modem only gives me the 3 choices for bridge mode vs. PPP etc, there aren't any manual configuration options that I can locate.
I'd try all three options. For the option "PPP is on the modem" I would have thought that putting the Time Capsule into bridge mode would work, but evidently it did not. For either of the other options ("PPP is on the computer" and "Bridged Mode") I'd configure the Time Capsule to connect using PPPoE.
The Time Capsule Manual says this, to my further confusion:
+The Time Capsule has three hardware addresses printed on the bottom of the case:+
+-AirPort ID: The two addresses used to identify the Time Capsule on a wireless+
network.
+-Ethernet ID: You may need to provide this address to your ISP to connect your+
+Time Capsule to the Internet.+
Those three "hardware addresses" are MAC ("Media Access Control") addresses. Those are assigned by the manufacturer and are completely different from IP addresses.

Similar Messages

Time Capsule only works for one device at a time, how to make it capable to be used for multiple devices at times

Time Capsule only works for one device at a time, how to make it capable to be used for multiple devices at times.
Please help to set it up, thanks in advance

You need to give more info..
Firstly only works for what.. networking.. backup.. wireless. You need more nouns.. more adjectives... describe what you want and what fails.. then we can figure out why.
Most likely you have bridged it when it should be in router mode..
Most likely you are using Lion or ML which has the airport utility bridge the TC by default.
Change it to working as a router. That might help.
If you press reset button it will default back to router btw.
If you are on Lion.. use a real utility. http://support.apple.com/kb/DL1547

Synaptics touchpad on HP Mini 110 Windows 7 32 Bit - not working for one user - working for another

Hi,
I recently have an issue with Synaptics touchpad on HP Mini 110 Windows 7 32 Bit - NOT working for one user - working for another.
Windows 7 updates recently installed ???
By checking the device properties on the user that works - "Synaptics PS/2 Port Touchpad 13/10/2011 Version 15.3.29.0"
When the other user logs on, the touchpad works for a few seconds, then a displays a black square with a red diagonal line through it, then the touchpad won't respond. Trying to use the keypad to navigate to system diagnosics or anything to find further info is useless....

Hey eagle_no11,
Thank you for joining the HP Support Community!
I will do my best in assisting to hopefully get the TouchPad to work on the second user profile.
What I would like to start off with, is to restore the original Synaptics drivers onto the profile that is not working correctly. I have included the document Using Recovery Manager to Restore Software and Drivers (Windows 7).
Once you have installed the original drivers, you will need to complete all updates from both HP, as well as Windows. For these updates, if you open the HP Support Assistant, and select Maintain, you should see an option for updating.
Please let me know how these steps do work out for you.
Have a great day!
I worked on behalf of HP

Flash only works for one user

Using IE7. I have three users on my computer. All
have Administrator level access. Flash only works for one of them.
When attempting to play a video on YouTube for example it says "You
either have JavaScrip turned off or an old version of Adobe Flash
Player."
JS is turned on and the current version of Flash Player is
installed.
So does anyone know what is going on here?
Thanks

I was able to fix my problem of Flash only working on user
account. I did the following two steps to correct the problem:
1. First uninstall the Adobe Flash Player plug-in and ActiveX
control by following the instructions stated in
tn_14157.
2. Second Download SubInACL from Microsoft to fix permission
issues that prevent the Flash Player installation by following the
instructions stated in
fb1634cb.
Following the above two steps, fixed my problem of only
having Flash run on only one user account. Now it runs on all four
user accounts.
As a side note: The Flash Player plug-in and ActiveX control
would not run in user accounts with Limited access. But when I set
the permission of the user account to administrative, then Flash
would work.
Regards,
Bob

Incoming Email not working for one web app, but IS working for others in same farm.

I have enabled incoming email in a large multi-web application farm running SharePoint 2013 SP1 and the Feb 2015/March 2015 CUs that were pushed down in Windows Updates. It works just fine for two web applications, but it will not work for one particular
web application. I see the email land in the /drop folder. If I remove the email address from the library in http://nonworkingapp web
application and use it on a library in a http://working web application, then the email is processed successfully. Conversely,
if I take an address from a library in http://working and move it to a library inhttp://nonworkingapp it
does not work. I've tried multiple site collections on http://nonworkingapp. This rules out any SMTP issues, etc. and means
the issue is bound to this web application. Permissions are the same between the "non-working" and "working" locations: domain users are members on the site, and the library inherits permissions from the site. The App Pool and Timer
Service accounts have rights to the folder and to the library.
The error in the ULS log is the typical error processing message, but it gives no additional information even though I have enabled Verbose logging.
The Incoming E-Mail service has completed a batch. The elapsed time was 00:00: 00.0156294. The service processed 2 message(s) in total. Errors occurred processing 2 message(s): Message ID: Message
ID:
Typically, you see "alias not found" or some permissions or quota issue here, but this issue is NOT the same as those. In this case NO additional information is provided in ULS.
Edit: running stsadm.exe -o refreshdms -url http://one/failing/site fixed some similar issues where "Unknown alias" was
reported even though the list did have an alias (see here:http://blogs.technet.com/b/vinitt/archive/2009/07/15/e-mail-enabled-list-alias-information-is-not-synchronized-between-configuration-database-and-content-database.aspx).
This did not fix the issue for the case mentioned above.
What could possibly be the issue preventing incoming email from working on this one web application?

Thanks for your reply. Incoming E-Mail was running on all 3 WFE, however I do not think this was the cause. As noted, _other_ emails send to http://workingapp are working just fine. I can send two emails - one to a library on http://workingapp
and another on http://notworkingapp. The email to http://notworkingapp will sit in the drop folder, while the one to http://workingapp will be processed correctly. In addition, the ULS log on WFE1 indicates an attempt to process the file fails.
So clearly, the timer job on WFE1 is running and attempting to process the file. For kicks, I disabled the service on WFE2 and WFE3, but with no change in the behavior.
WRT to #1, I have done this already (as noted in the original post). I can remove an alias from http://workingapp and place it on http://nonworkingapp and it is not processed. If I return it to http://workingapp it is processed. In other
words, I go into Library Settings -> Incoming Email for a working library, and copy the alias, then disable incoming email for that library. I then go to Library Settings -> Incoming Email for a non-working library, enable incoming email, and paste
the alias. Once done, emails sent to the alias are not processed. I then do the reverse, and it works again.
On #2, I have already tried multiple libraries on http://nonworkingapp (also as noted in the original post).
In my environment, incoming email does not work for any library on http://nonworkingapp, but does work for any library on http://workingapp. Troubleshooting listed above has ruled out any problem with basic mail server configuration or library settings
- the problem is bound to http://nonworkingapp
I'm not sure what you mean by "steps to reproduce the issue". If I knew that, I would probably be able to solve the issue. The best I could come up with to describe the situation would be:
Set up SP 2010 in a three-node configuration with multiple web apps
Enable incoming email and confirm it works
Migrate to a SP2013 SP1 farm in a three node configuration.
Enable a new email alias for a library
Observe that it doesn't work for one web application.
Obviously, it's pretty unlikely that attempting that in a lab would actually have the same result.

Auto To working for one material and not working for other material

Hi,
Hope everybody is doing fine.
I have configured the auto TO. Its working fine for one material and not working for the other material. I checked the material master and wm 1,2 views have the same fileds / values. What could be wrong?
I didn't setup the back ground processing job. Is that is affecting it?
thanks for any help.
regrads,
KHAN

Thnaks,
You are right but then what could be wrong? Its working for one material and not working for otehr material? Any clue?
Appreciate your time charlie

Imessage is not working for one person

My imessage is not working for one person.
Its been like this for about 2 days
I have an iphone 5
imessage is on
both phones reset network settings,deleted and remade contact, etc.

Does the other person have iMessage on, too? Is the specific phone number/address you are trying to reach them at show up for them in Settings > Messages > Send & Receive?

Airplay works for one user but not for another on the same machine

I have the problem where airplay works for one user but not for another and both users are on the same machine. For the user where it does not work, everything appears normal, it's just that there is no sound being transmitted. I have tried restarting the Airport express, restarting iTunes, repairing disk permissions. Any ideas about what can be done to resolve this?

my /etc/group:
root::0:root
bin::1:root,bin,daemon
daemon::2:root,bin,daemon
sys::3:root,bin
adm::4:root,daemon
tty::5:
disk::6:root
lp::7:daemon
mem::8:
kmem::9:
wheel::10:root,hans,ibm,gast
ftp::11:
mail::12:
uucp:x:14:
log::19:root
locate:x:21:
smmsp::25:
http::33:
games::50:
network:x:90:
video:x:91:
audio::92:ibm,gast
optical::93:hal
floppy:x:94:hal
storage:x:95:hal
scanner:x:96:
power:x:98:
nobody::99:
users::100:gast
dbus:x:81:
hans:x:1001:
vboxusers:x:108:hans
policykit:x:1002:
hal:x:82:
kvm:x:78:
nx:x:85:nx
avahi:x:84:
camera:x:97:
gdm:x:1003:
gast:x:1004:

Monitor works for one second, then blank

I have been reading many of the post people have put down about monitors and mac mini's, however can't find anyone with my problem.
I bought a mac mini and a cheap monitor from PC world, a Xerox 17" TFT, thinking that it would work fine. However when I connected them up using the DVI cable, at start up the monitor works for a second then blank. Turning it off and back on again brings the image back but again for just a second. This is annoying in that the mac mini is still in its welcome first run making it difficult to get beyond it to mess around with the monitor settings given a window of a second each time.
There was an adaptor that came with the monitor, but to use that I would have to plug that adaptor into the macs DVI adaptor as well, something I tryed but no luck, in fact no image at all.
Has anyone else had this problem?

I've had this problem too, resetting the PMU and PRAM usually helps:
http://docs.info.apple.com/article.html?artnum=300574
http://docs.info.apple.com/article.html?artnum=2238
Mario
Mac Mini Mac OS X (10.4.6) Core Duo / 2GB

ICloud shared photo stream stopped working for one subscriber

A shared photostream stopped working for one subscriber. Tried resending the invite several times but after the person clicks on the link, it says "stream no longer shared". Have tried alternate emails and no avail. Anyone else have this issue? I tried resending the invite to myself and to a phone number but also having the same issue. No issues uploading to the photostream or any issues for anyone else.

Reassigned email address in contacts from "home" to "iCloud" and that did the trick!

IMovie less than an hour. share to iDVD failed. read to share to media browser. worked for one movie. tried on different one and iDVD hung up and had to use force quit to get out of it. tried several times -- same result. suggestions?

iMovie less than an hour in length. share to iDVD failed. read in support to share to media browser. then made DVD through iDVD. worked for one movie. tried on different one and iDVD hung up and had to use force quit to get out of it. tried several times -- same result. suggestions?

Why start a new and very similar thread to your other one which you have not responded to (have you read the replies?)
I suggest that no response is made to this duplicate thread.

Classic - text ringtones work for one contact but not for others

Just got the new Blackberry classic. I'm having trouble with the ringtones for the text messages. The custom ringtone works for one contact but not for the others. I have taken the same custom ringtone that works for contact A and used it for contact B but it only works for A. B sounds the default ringtone from the default profile instead of the custom ringtone.
I have deleted all contacts and done a re-sync thinking something was corrupt. That didn't work.
None of the contacts have a link.
I have changed the notification profile and it still doesn't work.
I have deleted a contact and recreated it manually. It still doesn't work.
I finally deleted my dad's contact and from the phone app created a new contact. I set a custom ringtone for him and it worked. I of course had to recreate all his other information manually. Please tell me there is some other way to fix this than recreating manually all 147 contacts in my contact list.
I read that if the phone number has the hypen or space it won't work, but my dad's contact info that I created from the phone app has the hypen and it rings with the custom ringtone. Also contact A has no hypen in the phone number and it rings the custom ringtone. So that didn't seem to matter.
I have spent hours on Google and see that lots of people have had this problem (but not everyone) but have not yet found a solution.
Surely someone has found a fix for this issue.

Make sure that the contact has "Mobile" as the field for her number and not "iPhone".
Note that the iPad cannot send SMS messages.

So I have an iPad 2 for two years. Has never been dropped or in water or damaged in any way....now the volume is distorted and I get booted off the web all the time. Plus it shows and no service in top left corner. Any one have these issues?

So I got is iPad as a gift and the same issues I had with my iPhone 4S is also happening with my iPad. Will Apple cover the problem as it lies within there updates or something. All I know I have taken perfect care of both products and volume is distorted. Can't listen to music, I get booted off the web all the time, I can't even chat with Apple icare it won't work and no service shows on top left corner. What is wrong with Apple products? I'm thinking it's time to switch! I've had to change my iPhone twice now......first time for mic not working and then camera shutter kept sticking. Same on my iPad........ I don't want to pay to get this fixed as it's not my fault this is happening...... It's software apparently?

This really is starting to feel like a hardware issue than a software one.
Especially if hearing noises when you connecting up your iPad for charging.
Something happened to your iPad that has nothing to do with a software update.
This is why I recommend that
I can't help you any farther.
It sounds as if you really need to take this iPad in for a repair.
Since you are reluctant to do this, there is nothing more I can suggest to you.
Good Luck on whatever you decide to do.

Although I have not set up a voice mail password, my phone keeps asking for one. How do I turn that off?

Just bought an iPhone 5. Although I did not set up a voicemail password, it keeps asking for one. How do I turn that off?

I believe once you set and input the password on your iPhone it will NEVER ask you for it again, unless you restore your phone as a new device.
So, set a password, input it, then you shouldn't see that popup anymore.

Why is it when I go to open a file in Photoshop cc I get a "Could not complete your request because of a program error". I have uninstalled and re-installed software, It works for a short time then I get that error again when i go to open a file. Thank

@Why is it when I go to open a file in Photoshop cc I get a "Could not complete your request because of a program error". I have uninstalled and re-installed software, It works for a short time then I get that error again when i go to open a file. Thank you!

Without proper system information and other details like what files you work with nobody can tell you much. From corrupted prefs to issues with your PS swap file to actual problems with the fiel storage this could be anything.
Mylenium

AP Ex access works for one device connection, 2nd device gets booted off

Similar Messages

Maybe you are looking for