AS2 Adapter Configuration to Customer / no signature certificate

Dear all,
we start a project with an external Customer incl. Certificates.
If we now start message processing we get follow error back:
Message processing goes fail. Reason: javax.resource.ResourceException: Fatal exception: javax.resource.ResourceException: SEEBURGER AS2: AS2 Adapter failure # java.lang.Exception: AS2 message composition failed: com.seeburger.ediint.edi.EDIMessageException: EDI message composing failed: no signature certificate, SEEBURGER AS2: AS2 Adapter failure # java.lang.Exception: AS2 message composition failed:
com.seeburger.ediint.edi.EDIMessageException: EDI message composing failed: no signature certificate
Any idea ?
What is the meaning of "no signature certificate" ?
Because we import the certificate info the Trustcenter form the partner and customized in
AS2 Receiver Configuration -> Encryption Certificate
Thanks
Kind regards
S. Kohler

Hello,
The error states "EDI message composing failed: no signature certificate"
...and for the signature, you are always using your own key and not the certificate that you receive from the partner.
(since you wrote " ... we import the certificate info the Trustcenter form the partner")
So the error message is correct in the way that the referenced entry cannot be used to create the signature.
Greetings
Stefan

Similar Messages

  • AS2 adapter-- Module tab configuration to call seeburger std mappings..!

    Hi Experts,
    Seeburger has been installed and i want to use AS2 adapter to make use the seeburger standard mappings.
    When i opened the module tab, its been found that for
    Sender AS2 adapter:
    Module Name                                     Module Key
    localejbs/Seeburger/solution/as2             solutionid
    localejbs/CallSapAdapter                         exit
    Module configuration
    _Modulekey      ParameterName               ParameterValue_
    Solutionid           Mappingname               SEE_ORDERS_UN_...
    can i use the above steps??  
    Is solutionid is enough to call the seeburger mapping?
    or
    do i need to use the Bic module to call the seeburger std mapping like below?
    Module Name                                    Module Key
    localjbs/CallBicXIRaBean                         bic
    Module configuration
    Modulekey     ParameterName               Parameter Value
    Bic               Mappingname              SEE_ORDERS_UN_...
    Kindly let me know.
    Regards
    Krupa.

    HI,
    For module configuration for As2 refer the below help.
    Sender configuration:
    AS2 identifier is the party identified which will be provided by the WAN network provider.
    Under the party identifiere tab
    Agency will be seeburger
    Scheme=AS2ID
    Name = WAN network no of the partner who is sending the file
    Few changes in the module parameter tab.
    localejbs/CallBicXIRaBean bic
    CallSapAdapter 0
    Module configuration:
    bic= destSourceMsg = MainDocument
    bic= destTargetMsg = MainDocument
    bic= mappingName= See_E2X_EDIFACT_ORDERS_UN_D93A
    Receiver AS2 adapter configuration:
    When the adapter is used in a receiver channel, it obtains a message from the Integration Engine and sends it to a business partner. In this case, the following steps are required:
    1. Define the channel as a Receiver channel on the Parameters tab
    2. The last step ensures the module sequence is complete:
    Make sure the module ModuleProcessorExitBean does exist in the module sequence:
    Module Name=localejbs/ModuleProcessorExitBean
    Type=L
    Module Key=Exit
    • with the following module parameter:
    Module Key=Exit
    Parameter Name=JNDIName
    Parameter Value=deployedAdapters/SeeXIAS2/shareable/SeeXIAS2
    Refer the below thread which has the same discussion.
    Re: Pls.. Help Needed.. Seeburger Mapping Names..!!
    Thanks and Regrds,
    Chirag

  • Seeburger AS2 Adapter Error :AUTHENTICATION_ERROR

    i am doing the scenario for Purchase Order -> XI ->File
    custumer is posting the purchase order
    and XI Receives the PO using AS2 Adapter (Seeburger) and sends the output as File
    i have done all the AS2 Adapter configurations as mentioned below but still i am getting the error in Seeburger Monitoring, the Error is Authentication_Error
    1. Communication chennel
      Adapter Type : AS2
      Direction : Sender
    Transport protocol : HTTP
    Message Protocol : AS2
    AS2 : Authentication Required is Enabled
    Message Subject : Filled which is in Seeburger Monitor
    2. Sender Agreement
    Sender Communicational chennel which is created above
    Security Setting
    AS2 Sender Config :
    Authentication Certificate : Customer public key
    AS2 Receiver Config :
    Decryption Key : Private key
    3. in Party Identifiers
    Party Name
    AS2 ID
    is there any settings missing to rectify the error "AUTHENTICATION_ERROR"

    Hi
    Check with PIAPPLUSER authentication
    With this Check the following content on AS2 may be you get more clue.
    http://www.customware.net/repository/display/WMFAQ/AS2-authenticationfailureinreceivingEDIINT+MDN
    https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/135b0b94-0701-0010-f6a9-86a14057544a
    https://www.sdn.sap.com/irj/sdn/wiki?path=/display/bpxproj/edi%2bwith%2bpi
    Handling EDI interfaces using Seeburger BIC modules
    Thanks
    Gaurav

  • SEEBURGER AS2: AS2 Adapter failure -- CryptoApiException: Access Denied.

    Hi,
    I am trying to send AS2 message to my partner by using Certificates and I am getting the following error at AS2 receiver adapter.Looks like it doesn't have User Credentials to access the certificates.But we provided all the details.We are not sure where it is going wrong.
    2008-08-30 14:49:42 Error Unable to forward message to JCA adapter. Reason: Fatal exception: com.sap.aii.af.ra.cci.XIRecoverableException: SEEBURGER AS2: AS2 Adapter failure # java.lang.Exception: AS2 message composition failed:com.seeburger.ksm.cryptoapi.exception.CryptoApiException: Access Denied., SEEBURGER AS2: AS2 Adapter failure # java.lang.Exception: AS2 message composition failed: com.seeburger.ksm.cryptoapi.exception.CryptoApiException: Access Denied.
    Can anyone please suggest us what is missing and where it is going wrong?
    Regards
    Stephano

    Hi,
    1) First of all create the Seeburger Certificates.
    2) You have to deploy those certiates in your Visual Administrator.
    After that in  Interration Builder -
    > Receiver Agreement -
    > In Security Settings -
    >
                       AS2 Sender Configuration -
    > Signing Key -
    >give the certificate name over there.
                       AS2 Sender Configuration -
    > Encription Certificate & Authenitication Certificate is there
                       u have to give u r certificate names over there.
    Thanks,
    Satya Kumar

  • Seeburger AS2 Adapter

    Hi,
    I need few information how to implement seeburger adapter(Using AS2 or FTP) with XI. I have a requirement to convert the EDI Ansi X12 messages from a EDI system and post it into a R/3 system using XI.
    The client system(EDI system) is in US has VAN  and we have the R/3 in India. So do we need to establish a VAN connectivity or it can directly access the client VAN to take the EDI messages.
    Do clarify whether to go for AS2 or FTP, and what are the advantages of each.
    I went thro few documents from Seeburger which comes up with the package of Generic FTP adapters or we have a Standalone AS/2, or BIS:HUB and spoke.
    Regards,
    Nithiyanandam

    HI,
    Brief about the FTP/VAN adapter:
    The SEEBURGER FTP/VAN Adapter is responsible for transmitting files according to the File Transfer Protocol, with the particular support of various VANs. This protocol was installed as a user gateway protocol by several of the largest VAN providers, such as IBM, GE and Sterling IIB and Sterling Commerce.
    The FTP/VAN adapter must be configured in the configuration part of the Integration Builder. The adapter is based on the Adapter Framework and is executed by the SAP J2EE Adapter Engine as shown in the diagram below.
    The FTP/VAN Adapter supports the following protocols:
    • IBMIE VAN, all report options.
    • GEIS (GeMarkIII) and GeMark3000, all report options, report file is only extracted, if needed.
    • EXITE (ECODEX), EDIFACT file processing, DISPATCHED reports.
    • Sterling Commerce and Sterling IIB.
    • MCI EDI*Net.
    The following FTP options are supported:
    • SSL, both IMPLICIT and AUTH_TLS support, server authentication.
    • All popular FTP proxy types like: USERWL, USERWOL, SITEWL, OPENWOL.
    • Active and Passive connection modes.
    • "KeepAlive" feature.
    • Binary, ASCII and custom transfer types.
    Refer the below thresd which taks about the AS2 adapter configuration inroder to convert the EDI to XML message the similar configuration needs to be done in case of VAN/FTP adapter.
    Re: Pls.. Help Needed.. Seeburger Mapping Names..!!
    Seeburger adapters like FTP,OFTPS,AS2,X400 are used for B2B scenario where the file is coming through WAn network or mailbox. As XI dont have capability to convert the EDIFACT format file to XML the same work will be done by seeburger adapters.
    The SEEBURGER Business Integration Converter (BIC) is an any-to-any format converter, used to translate EDI data and legacy data formats into XML and vice versa. It can also be used for complex, high performance XML-to-XML mappings or to interface to existing JDBC data sources.
    Supported EDI formats include:
    • ANSI
    • EDIFACT
    • INHOUSE
    • IDOC
    • XML Schema
    • XML DTD
    • CSV
    • Delimited Data
    • positional data
    • SWIFT
    • EANCOM
    and many more.
    See for converting the EDI XML to EDI and XML-EDI you need to have a seeburger mapping program at the adapter module which does the conversion. For this module you need a BIC tool of seeburger which provides the different module program for EDI to XML and XML-EDI. This program needs to be deployed on XI and through adapter it has to be called for conversion.
    Seeburger provides the std mapping program which has to be deploy on to XI and we need to give it to module tab in adapter which does the conversion.
    Here are the some of the std mapping program which is provided by seeburger.
    See_E2X_INVOIC_UN_D96A
    See_E2X_INVOIC_UN_D99A
    See_E2X_ORDERS_UN_D96A
    See_E2X_OSTRPT_EAN_D96A.
    We need to take the license from seeburger and we need to deploye the seeburger adapters then only we can see in adapter list on XI.
    Thanks and Regards,
    Chirag Gohil

  • Error in AS2 adapter. Object not found in lookup of as2.. Its urgent..!!

    Hi AS2 experts,
    *When i tried sending an xml to partner system using AS2 adapter.. Mapping is succesfull and message is failing in receiver AS2 adapter.
    1. I used the following parameters in AS2 Module.
    ModuleName                                                       Module Key
    localejbs/Seeburger/solution/as2                              solutionid
    localejbs/ModuleProcessorExitBean                          exit
    ModuleKey    ParameterName         ParameterValue
    exit                JNDIName     deployedAdapters/SeeXIAS2/shareable/SeeXIAS2
    Iam getting the following error.
    Success     MP: Processing local module localejbs/Seeburger/solution/as2
    Error :   MP: Exception caught with cause com.sap.engine.services.jndi.persistent.exceptions.NameNotFoundException: Object not found in lookup of as2.
    Error :  Exception caught by adapter framework: Object not found in lookup of as2.
    Error : Delivery of the message to the application using connection AS2_http://seeburger.com/xi failed, due to: com.sap.aii.af.ra.ms.api.RecoverableException: Object not found in lookup of as2.: com.sap.engine.services.jndi.persistent.exceptions.NameNotFoundException: Object not found in lookup of as2..
    2. When i tried by removing Modulename "localejbs/Seeburger/solution/as2"
    It is showing the below error like AS2ID is missing.. but its there in party configuration.
    Error :
    Unable to forward message to JCA adapter. Reason: Fatal exception: com.sap.aii.af.ra.cci.XIRecoverableException: SEEBURGER AS2: AS2 Adapter failure # Outbound configuration error: Sender configuration incomplete - perhaps AS2ID missing.., SEEBURGER AS2: AS2 Adapter failure # Outbound configuration error: Sender configuration incomplete - perhaps AS2ID missing..       
    Can anyone has idea what might be wrong.
    Kindly suggest me asap.
    Thank You.
    Regards
    Seema.

    Hi,
    Plesae go through below links
    /people/bla.suranyi/blog/2006/06/08/sap-xi-supports-edifact
    EDI Adapter by SeeBurger
    https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/206e2b65-2ca8-2a10-edad-f2d1391644cb
    B2B(EDI) Integration using SAP Netweaver XI and Seeburger AS2 Adapter
    https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/00f9cdf5-d812-2a10-03b4-aff3bbf792bf
    Integrating XI with SeeBurger
    https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/6dc02f5d-0601-0010-cd9d-f4ff9a7e8c33
    and
    Check with below configuration
    Configuration for AS2 or simple file adapter.
    We are using this module configuration for converting EDI D96A format to XML:
    1 localejbs/CallBicXIRaBean Local Enterprise Bean bic
    2 localejbs/CallSapAdapter Local Enterprise Bean 0
    bic destSourceMsg MainDocument
    bic destTargetMsg MainDocument
    bic logAttID ConverterLog
    bic mappingName See_E2X_ORDERS_UN_D96A
    bic saveSourceMsg ORIGINAL_EDI
    can someone please tell me the module configuration for reverse mapping at receiver end,i.e.,XML to EDI D96A
    basically,I need mapping name for this.
    Scheme=AS2ID
    Name = WAN network no of the partner who is sending the file
    Sender AS2 adapter configuration:
    Few changes in the module parameter tab.
    localejbs/CallBicXIRaBean bic
    CallSapAdapter 0
    Module configuration:
    bic= destSourceMsg = MainDocument
    bic= destTargetMsg = MainDocument
    bic= mappingName= See_E2X_EDIFACT_ORDERS_UN_D93A which does the conversion of EDI-XML.
    Receiver AS2 adapter configuration:
    When the adapter is used in a receiver channel, it obtains a message from the Integration Engine and sends it to a business partner. In this case, the following steps are required:
    1. Define the channel as a Receiver channel on the Parameters tab
    2. The last step ensures the module sequence is complete:
    Make sure the module ModuleProcessorExitBean does exist in the module sequence:
    Module Name=localejbs/ModuleProcessorExitBean
    Type=L
    Module Key=Exit
    • with the following module parameter:
    Module Key=Exit
    Parameter Name=JNDIName
    Parameter Value=deployedAdapters/SeeXIAS2/shareable/SeeXIAS2
    File receiver:
    localejbs/CallBicXIRaBean bic
    CallSapAdapter 0
    Module configuration:
    bic= destSourceMsg = MainDocument
    bic= destTargetMsg = MainDocument
    bic= mappingName= See_X2E_EDIFACT_ORDERS_UN_D93A
    ONly the mapping program name changes from E2X to X2E. IN ur case it will be See_X2E_ORDERS_UN_D96A
    Thanks
    Swarup

  • Seeburger AS2 Adapter - Cookie Control

    Hello together,
    on my current project I am facing this kind of problem during AS2 communication:
    Our partner provides us a cookie containing a session ID. Using this cookie we are able to send messages to our partner. This cookie has no expiration date, because we should be able to send messages for an unknown amount of time, and if it had an expiration date, some messages would fail for no logical reason.
    On the partner side, though, the sessionIDs are invalidated after 600 seconds of inactivity. This is done for security reasons, as it is considered that after this amount of inactivity, the connection must end.
    When we tried to connect after 10 minutes, using this cookie with the old sessionID, the response is an invalid SessionID or session expired.
    Our partner suggested to delete the cookie after sending messages. But on the AS2 adapter configuration I see no option for cookie control.
    Any ideas? Keep in mind that our partner would rarely change its setup.
    With kind regards
    Frank Opitz

    Am not sure but do AS2 adapters have a Cookie Option? Or are you talking about Http Keep Alive option?
    Can you try to disable this option in the Receiver As2 adapter and give it a shot?
    Regards
    Bhavesh

  • AS2 Adapter EDI scenario - question

    I am working on a EDI scenario, involving AS2 adapter.
    Could anyone tell me any steps to be done on ABAP engine.
    reg

    Hi Naveen,
    follow the below steps:
    1) First deploye the Std seeburger mapping provided by see burger on XI
    2) If you are using the AS2 adapter then you have to install the AS2 server on XI server.
    3) Once you install the std seeburger on SAP XI server you will see the AS2,X400,OFTPS,VAN adapter on XI ID.
    5) You need to call the std mapping in the adapter module which does the conversion from EDI to XML and XML to EDI.
    steps in IR and ID.
    In IR:
    You need to use the Standard XSD provided by Seeburger for different mesages like EDFACT ORDERS D96A etc in IR and other steps are similar which we do for the normal scenarios.
    In ID:
    This is the scenario for AS2
    Seeburger has provided std mapping which need to be deployed on Xi server and will be used in XI adapter module tab for EDI-XML and XML-EDi conversion.
    Example of mapping:
    See_E2X_INVOIC_UN_D96A
    See_E2X_INVOIC_UN_D99A
    See_E2X_ORDERS_UN_D96A
    See_E2X_OSTRPT_EAN_D96A.
    1) After deploying mapping program.
    We need to give the AS2ID in the party identifier tab,AS2ID that is entered here will be used for identifying the sender and receiver of the document.
    1)The value of the Agency field must be Seeburger.
    2)The value of the Schema field must be AS2ID.
    Every partner is assigned the WAN no which is provided by the WAN service provider. That WAn no we need to configure in the party identifier tab
    Configuration in adapter:
    Under the party identifiere tab
    Agency will be seeburger
    Scheme=AS2ID
    Name = WAN network no of the partner who is sending the file
    Sender AS2 adapter configuration:
    Few changes in the module parameter tab.
    localejbs/CallBicXIRaBean bic
    CallSapAdapter 0
    Module configuration:
    bic= destSourceMsg = MainDocument
    bic= destTargetMsg = MainDocument
    bic= mappingName= See_E2X_EDIFACT_ORDERS_UN_D93A which does the conversion of EDI-XML.
    Receiver AS2 adapter configuration:
    When the adapter is used in a receiver channel, it obtains a message from the Integration Engine and sends it to a business partner. In this case, the following steps are required:
    1. Define the channel as a Receiver channel on the Parameters tab
    2. The last step ensures the module sequence is complete:
    Make sure the module ModuleProcessorExitBean does exist in the module sequence:
    Module Name=localejbs/ModuleProcessorExitBean
    Type=L
    Module Key=Exit
    • with the following module parameter:
    Module Key=Exit
    Parameter Name=JNDIName
    Parameter Value=deployedAdapters/SeeXIAS2/shareable/SeeXIAS2
    You can refer my thread reply:
    Re: Pls.. Help Needed.. Seeburger Mapping Names..!!
    Re: Seeburger AS2 adapter...
    Re: AS2 Module tab.. Mapping Names for modified Standard Msg types ? ? BIC ??
    AS2 adpater-- Configuration details for both SND and RCV.
    AS2 Sender Adapter -- Need few details.
    EDI-SEEberger-XI-IDOc-R/3
    flow of the data from EDi to SAp r/3 using seeburger:
    1) Data will be coming thorugh WAN or mailbox.
    2) If its coming through WAN then every WAN provider will give the partner which is sending the data a partner number for indentification.
    3) In your AS2 channel you need to configure the party and for that party you need to give the WAN number which is proivded for that partner. So it will run that configuration whenever that partner send the data.
    4) In the adapter you have to give the mapping program name which does the conversion of EDI-XML and XML-EDI.
    5) Once you XML is generated then it will be used in MM
    6) At the receiver if its IDOC adapter then IDOC adapter will post the IDOC to R3 system.
    Thnx
    Chirag

  • Seeburger - XI AS2 Adapter Sender service configuration

    Hi,
    I need to know how to configure the seeburger AS2 adapter sender service in XI ( EDI -
    > IDOC).
    I have some pre-requisites that are needed to setup.
    1. SSL certificate
    2. AS2 Certificate (public key)
    Kindly anyone provide me the guidance or if any docs/pdf's. your help is appreciated.
    Thanks,
    lakshmi

    Refer these
    EDI Adapter by SeeBurger
    https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/206e2b65-2ca8-2a10-edad-f2d1391644cb
    B2B(EDI) Integration using SAP Netweaver XI and Seeburger AS2 Adapter
    https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/00f9cdf5-d812-2a10-03b4-aff3bbf792bf
    Integrating XI with SeeBurger
    https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/6dc02f5d-0601-0010-cd9d-f4ff9a7e8c33
    Thanks

  • Error at AS2 adapter level...There is no certificate with such alias

    Hi All,
    Iam sending the 856 message through AS2 adapter to partner and i got the below error at the adapter level.
    Unable to forward message to JCA adapter. Reason: Fatal exception: com.sap.aii.af.ra.cci.XIRecoverableException: SEEBURGER AS2: AS2 Adapter failure # java.lang.Exception: AS2 message composition failed: com.seeburger.ksm.cryptoapi.exception.CryptoApiException: java.security.PrivilegedActionException: com.seeburger.ksm.cryptoapi.exception.CryptoApiException: There is no certificate with such alias, SEEBURGER AS2: AS2 Adapter failure # java.lang.Exception: AS2 message composition failed: com.seeburger.ksm.cryptoapi.exception.CryptoApiException: java.security.PrivilegedActionException: com.seeburger.ksm.cryptoapi.exception.CryptoApiException: Th
    Exception caught by adapter framework: Fatal exception: com.sap.aii.af.ra.cci.XIRecoverableException: SEEBURGER AS2: AS2 Adapter failure # java.lang.Exception: AS2 message composition failed: com.seeburger.ksm.cryptoapi.exception.CryptoApiException: java.security.PrivilegedActionException: com.seeburger.ksm.cryptoapi.exception.CryptoApiException: There is no certificate with such alias, SEEBURGER AS2: AS2 Adapter failure # java.lang.Exception: AS2 message composition failed: com.seeburger.ksm.cryptoapi.exception.CryptoApiException: java.security.PrivilegedActionException: com.seeburger.ksm.cryptoapi.exception.CryptoApiException: Th
    The certificate has already been uploaded and the AS2ID is defined as one of the identifiers of the party.
    Anyone has any idea what might be wrong? Did i miss anything?
    Waiting for your answers.
    Regards
    Lex

    I am having the same issue.  
    I receive the com.seeburger.ksm.cryptoapi.exception.CryptoApiException: java.security.PrivilegedActionException
    message plus the "unable to find alias name TRUSTED\".
    It appears that after the outbound message is transformed to XML iin XI then sent to Seeburger's BIC for EDI format translation, then sent to AS2 for encryption/transmission, the AS2 adapter cannot find the key store that holds the certificates I am using.
    Am I missing some configuration that points the to the keystore I need ?
    Thanks for any and all responses.
    Andy

  • AS2 Sender configuration - Authentication Certificate

    Hello guys,
    We're implementing EDI with a partner with AS2. We have AS2 sender adapter configured. Everything works fine (we're able to receive data from partner and send back MDN) without signing.
    Now we're working on getting data signed. We have uploaded partner cert to keystore (TrustedCAs) and have provided partner with our certificate as well.
    On Sender agreement--> Security Settings --> AS2 Sender Configuration --> Authentication Certificate how do we specify the certificate we're using. Should it be just the fullname like TrustedCAs/PartnerCert ?
    Also How should we specify the Decryption Key and Signing Key under AS2 Receiver Configuration?
    I was expecting to be able to choose from available keystores, but it is a free text field.
    Can anybody please help me on this?
    Thanks
    Karthik

    Hi Karthik,
    >>On Sender agreement--> Security Settings --> AS2 Sender Configuration --> Authentication Certificate how do we specify the certificate we're using. Should it be just the fullname like TrustedCAs/PartnerCert ?
    You need to mention the fullname  as TrstedCAs/PartnerCert.
    >>Also How should we specify the Decryption Key and Signing Key under AS2 Receiver Configuration?
    Yes you need to since you are using signed messages here..
    Regards
    Suraj

  • I created a signature ID and customized the signature; however, when I go to sign it only shows the name layout or graphic image? How do I go back to using the certificate?

    Dear Forum
    I was using Adobe version XI and the signature feature disappeared from the menu. Now I downloaded Acrobat Reader DC. Using the menu and instructions I created a signature ID and customized the signature; however, when I go to sign a document it only shows the name layout or graphic image? How do I go back to using the certificate that I created?
    Any help would be greatly appreciated.
    Regards
    Carlos

    Firefox works fine on Windows 2000 SP4 for me.
    Any chance you have a dial-up connection that uses a web accelerator to speed the loading of content?

  • Receiver AS2 Adapter issue.....Failed to get configuration from DATABASE. S

    Hi,
    Iam doing prototyping for File -AS2 adapter and ended up with below erros.
    Error type: COMPONENT_ERROR >> Error date: 6/17/11 8:04 AM >> Description: AS2 Adapter failure Outbound configuration error: Failed to get configuration from DATABASE. Sender configuration incomplete - perhaps AS2ID missing.. com.seeburger.as2.AS2Plugin.execute(AS2Plugin.java:379) [6/17/11 8:04 AM]
    and
    Message processing failed. Cause: javax.resource.ResourceException: Fatal exception: javax.resource.ResourceException: SEEBURGER AS2: AS2 Adapter failure # Outbound configuration error: Failed to get configuration from DATABASE. Sender configuration incomplete - perhaps AS2ID missing.., SEEBURGER AS2: AS2 Adapter failure # Outbound configuration error: Failed to get configuration from DATABASE. Sender configuration incomplete - perhaps AS2ID missing..
    The setting i have made during configation are :
    1> Reciver Party with Agency,Schema and Name entered.
    2>Identifiers for both Sender and reciver channel fileld with values seeburger and AS2ID.
    3>Used Sender uses Virtual reciver in sender aggremnet.
    4> Reciever CC have modules localejbs/Seeburger/solution/as2 and localejbs/ModuleProcessorExitBean in sequence.
    Please provide solutions to overcome the issue.
    As this is prototyping, i have downloaded Free As2 client and trying to send files to that client from PI.

    Hi Dinesh,
    make sure to also configure a report channel (refer to the sample chapter in the SEEBURGER AS2 documentation) in order to receive AS2 MDNs for your sent message. Additionally report channels are needed if the SEEBURGER specific TransmissionReports are requested.
    Hope that helps
    Greetings
    -Sascha-

  • Can SAP XI AS2 Adapter process flat files? Pl. tell me how to configure it

    I have a requirement to read and write delimited ASCII flat files using the AS2 adapter in SAP XI. The AS2 adapter should be able to read from delimited ASCII Flat files and also write to delimited ASCII flat files. Kindly let me know how to configure the AS2 adapter so that it can read and write delimited flat files. I badly need to know this configuration for a client requirement which requires file processing by the AS2 adapter in XI 7.0. Thanks in advance

    Hi,
    Is the requirement is to just read the flat file and process it ? if so, u can use File Adapter provided , ur source system provides u the data in the file format in the some directory
    following thread discussions may help u -AS2 adapter-
    Seebuger AS2 adapter for XI as sender for multiple messages
    Seeburger AS2 Adapter
    Hope this helps,
    Regards,
    Morthy

  • Idoc to Different Trading partners using AS2 Adapter

    Hello experts,
    I have a requirement where we have to send an Idoc to different trading partners using van.
    On the receiver side AS2 adapters will be used.There are many trading partners here.Can someone guide me through? ..
    The entire scenario will be done in SAP PO 7.4
    Breaking the entire scenario in the following parts---
    1)IDoc on sender side--What will be partner profile type? Will it LS or any other (BP, GP or KU??)
    2)AS2 configuration details---AS2 adapter is available in the dropdown of adapter list.What are the config details for AS2?
    3)Trading partner mechanism-How this can be achieved?..what this essentially achieves ? any step by step guide available? Does it take care of sending the Idoc only to VAN or sending Idoc to different trading partners directly bypassing VAN?
    4)Is using NWDS suggestible?--Is it convenient?
    Any help/step by step blog will be of great help.
    If I miss anything in the entire scenario, please let me know
    Thanks
    Ayan Chaudhuri

    Hi Ajay,
    1)IDoc on sender side--What will be partner profile type? Will it LS or any other (BP, GP or KU??)
    -->>The partner type is depend on your scenario. AS2 adapter is used for B2B communication and usually to vendor and customers.
    This purchase Order should go to the particular vendor as a sales order. Then we use partner type as LI -- Vendor.
    Similarly when we sell some materials to our customers, we create the Sales order to our customer. Then we use Partner type as KU - Customer
    Partner Type GP---Business Partner
    Partner Type KU---Customer
    Partner Type LI---Vendor
    Partner Type LS---Logical system
    Partner Type US--User
    2)AS2 configuration details---AS2 adapter is available in the dropdown of adapter list.What are the config details for AS2?
    -->> to configure as2 connection you need following details from trading partner
    AS2 ID
    server address with URL extension
    TP certificate
    MDN address and type (Sync, asyn and signed or not signed)
    Message communication encryption algorithm
    Compression is required or not and if req. which algorithm to use
    3)Trading partner mechanism-How this can be achieved?..what this essentially achieves ? any step by step guide available? Does it take care of sending the Idoc only to VAN or sending Idoc to different trading partners directly bypassing VAN?
    -->> If you are communicating through VAN then you need to send the message to VAN and VAN will route the message to respective TP.
    4)Is using NWDS suggestible?--Is it convenient?
    -->> NWDS is another option to create scenario, it is depend on developer which one he want to use.
    The belog blog might be useful
    Easy-to-use AS2 software - part IV
    B2B- EDI Inbound -Step by Step Configuration
    regards,
    Harish

Maybe you are looking for