ASA5512-X Setup using Management Interface

I have a brand new ASA5512-X running 8.6.1, and am trying to do an initial setup using the Quick Start Guide that came with it.  However, the Management Interface is not working.  I have a PC connected and set to use DHCP, but the port is not active. 
I connected a console cable and can see in the config that the interface is shutdown.  So I set it to active, and the port is now active, but is not giving out a DHCP address as the guide says it should.
I would like to use the ASDM Startup Wizard to configure this device, so how do I get it to work the way the instructions say it should?
Thanks!

Hello,
Try by console cable to use the commad:
config factory-default
and in case you don't have this:
ssl encryption des-sha1
It should get your ASDM working.
Let me know how this works for you.
Regards

Similar Messages

  • WLC to use Management Interface & Few more getting started Questions

    Hello,
    I'm yet to implement the Wireless LAN in one of our client's corporate office. There 40 x 1130AG LWAPP AP's and 4404 WLC with ACS 4.x for the Authentication of the Wireless Clients who is trying to access the LAN.
    For the WLC to connect to the Dual Core Switch, i need to use only one Management Interface with Distribution System port 1 being the Primary and mapping the DS Port 2 as the Backup port for the Management Interface. Is this Right? or do i have configure Dynamic Interfaces as well. Is management interface for accessing / management and configuration only? Management Interface will communicate with ACS for AAA and AP's who would like to associate with the WLC, is this Right?
    Note: WLC, AP's, Wireless Clients & AP's are in the same IP Subnet.
    Few other question of WLAN's so it helps me during implementation -
    • Can I use the 802.1x Authentication application found in the Windows XP for the Wireless Interface; instead of Cisco Client Application. For this; I have to configure the WLC / Wireless Client to use EAP algorithm; is this Right?
    • With the help of RRM, the channel interference between multiple AP's (3 - 4 AP's) in the same area is controlled by the WLC by changing the Channels used by the AP which is not same on all the AP's. Is this right?
    • How many Client Users will connect per Channels. 802.11 a / g will provide 11 Channels, is this Right?.
    • I'm trying to set in the WLC to limit the Client connections per AP to 25, can this be achieved?
    Please, can anyone help me in calrifying the above points.
    Regards,
    Keshava Raju

    Many Thanks Mr. Dennis for your help & Clarification.
    With ref to your reply point no# 1. I have actually planned to connect one Gig port of the controller to each of the Dual Cisco Core Switch setup. Can i use all 4 Controller Interfaces configured as LAG and Port 1 & 2 connecting to Core Switch 01 and Port 3 & 4 connecting to Core Switch 02?
    I have Final two more questions, Request you to help me calrifying this?
    • I'm willing to configure Multicast communication between the WLC & AP's. For this configuration is it necessary to Connect the WLC in a different VLAN than the VLAN of the AP's. Is it necessary that I have to set the controller to LWAPP Layer 3 mode to support the Multicast communication?
    • Though I do not have implementation experience of the WLAN. My understanding of the Interface settings on the WLC - is I will have to configure one Management Interface for in-band management. Do I have to configure AP-Manager Interface (to support Multicast communication) and to make the WLC to communicate with ACS for Client Authentication. All of the Wireless Devices including the ACS are in one VLAN / IP Subnet, is only one Management Interface is enough for communicating with AP's (with Multicast) and communicating with ACS for forwarding the Authentication messages between the ACS & Wireless Clients?

  • Mobility group only works using management interface?

    Hello,  in order to stablish the control traffic between 2 WLC-5508, it's necessary to use the management interface??
    It's possible using a dynamic interface o service port ?
    I think it only works with management interface,  but I don't understand the meaning of this text in the Configuration Manual:
    "Mobility control packets can use any interface address as the source, based on routing table."
    Thank you,

    No... mobility communication is done only with the management interface.
    Thanks,
    Scott
    *****Help out other by using the rating system and marking answered questions as "Answered"*****

  • PPDS: I have a setup matrix in SAP ECC 6.0, and want to transfer the same to APO using Core Interface.

    PPDS: I have a setup matrix in SAP ECC 6.0, and want to transfer the same to APO using Core Interface. Has anyone done it before?

    Hi Subhash,
    Please open this link to see the details:
    http://help.sap.com/saphelp_scm70/helpdata/EN/89/bd3e42ce98033be10000000a1550b0/frameset.htm
    You perform the data transfer in the following sequence:
    Plant
    Setup groups
    Work centers
    Routings
    You check the setup groups in SAP APO.
    You create the setup matrixes in SAP SCM.
    Thanks, Marius

  • Inventory management snapshot model using Datamart Interface

    Hi,
    We have implemented Inventory management NON-CUMULATIVE scenario.
    Now for reporting needs we are adding snapshot model and trying to use datamart interface to fill up snapshot cube.
    But how to get value of KF say "ZTOTALST" becuase NON-*** cube has only changes stored as "0RECTOTSTCK" and "0ISSTOTSTK". If anyone has implemented or has any ideas on using snapshot model  with datamart interface , please help .
    regards,
    Daljit Boparai

    Try out with this
    http://help.sap.com/bp_biv335/BI_EN/index.htm
    Regards
    Kumar

  • IDOC Interface Setup using ALE

    Hi,
    Can any 1 suggest the best possible configuration steps to setup a idoc interface to two different systems

    Hi Urstruly,
    Please see the links below. They should help you reach your goal.
    File to Multiple IDOC Splitting without BPM - Process Integration - SCN Wiki
    SAP Library - SAP Exchange Infrastructure
    Configuring Multiple Receivers in XI
    Regards,
    Jannus Botha

  • 5508 WLC HA pair - change management interface settings

    Hi,
    We have a pair of 5508 WLC's in a HA configuration that is working well at the moment, however I have noticed that the management interface is configured as untagged. I would like to change this to tagged and change the attached switch to trunk for these devices but if I try and edit the management interface through the GUI the VLAN and IP address section is greyed out and cannot be changed. While I could attempt it through the CLI and am comfortable doing that, the fact that it cannot be changed through the GUI implies that this should not be changed and so I am after further information. I don't have any lab equipment other than the HA pair in production so I cannot try changing it through the CLI at the moment. 
    The WLC's are in LAG mode if that makes any difference. I realise there may be downtime required for making this change but I am trying to work out the steps to get this done without having to drastically reconfigure things. 
    Any assistance would be appreciated. 

    Introduction of New Interfaces for HA Interaction
    Redundancy Management Interface
    The IP address on this interface should be configured in the same subnet as the management interface. This interface will check the health of the Active WLC via network infrastructure once the Active WLC does not respond to Keepalive messages on the Redundant Port. This provides an additional health check of the network and Active WLC, and confirms if switchover should or should not be executed. Also, the Standby WLC uses this interface in order to source ICMP ping packets to check gateway reachability. This interface is also used in order to send notifications from the Active WLC to the Standby WLC in the event of Box failure or Manual Reset. The Standby WLC will use this interface in order to communicate to Syslog, the NTP server, and the TFTP server for any configuration upload.
    Redundancy Port
    This interface has a very important role in the new HA architecture. Bulk configuration during boot up and incremental configuration are synced from the Active WLC to the Standby WLC using the Redundant Port. WLCs in a HA setup will use this port to perform HA role negotiation. The Redundancy Port is also used in order to check peer reachability sending UDP keep-alive messages every 100 msec (default timer) from the Standby WLC to the Active WLC. Also, in the event of a box failure, the Active WLC will send notification to the Standby WLC via the Redundant Port. If the NTP server is not configured, a manual time sync is performed from the Active WLC to the Standby WLC on the Redundant Port. This port in case of standalone controller and redundancy VLAN in case of WISM-2 will be assigned an auto generated IP Address where last 2 octets are picked from the last 2 octets of Redundancy Management Interface (the first 2 octets are always 169.254).

  • PC+AX Error - ....Windows is not setup to manage wireless network....

    I'm attempting to setup AX with Windows XP. I have a 802.11g Dlink router (DI-524) that I typically connect to using my work laptop. The PC has a direct connection to the router. The AX constantly flashes amber. I tried hard reseting the AX. When I run Airport Admin Utility on my PC the AX does not show up. However, I can see it using my laptop in the wireless connections. When I open Airport Setup Assistant I get the following error "This computer has no wireless interface enabled or Windows is not setup to manage wireless networks on this computer. If you have....."
    I'm not sure what do do from here. Appreciate any help.

    I have a Qwest wireless modem (model 2701hg-d) and am trying to set up the Airport Express (AX) to use already existing wireless network wirelessly (ie without the ethernet cable). Is this possible?
    In order to set it up I have the AX plugged into the modem via an ethernet cable. I have reset the AX and then run the Admin Utility. Once it recognizes the AX I then go to the Airport tab and select 'Join an Existing wireless Network (wireless client)' and then enter in the Network Name exactly as it is spelled in my modem configuration. I check the 'Internet' tab and it says connect using: Wireless Network adn the 'Network' tab is grayed out. Then I hit update and the admin utility no longer lists the AX and the AX light is blinking amber. Not sure what is going on. I am using v6.2 of the firmware.
    Do I need to use WDS?
    Also, does anyone know if multiple speaker selection is available for itunes pc like it is in itunes mac? Currently I can only play either my computer speakers OR my kitchen speakers.

  • ASA 5515 management interface

    I started to configure a new ASA 5515 to replace an 5510.  When I attempted to remove the "management-only" command from the Management0/0 interface I was greeted with the following error:
    "ERROR: It is not allowed to make changes to this option for management interface on this platform."
    Does this mean we can't use the managment interface anymore on these newer ASAs?  I was planning on using that port when we bought it.  If this is the case, let this be a warning to whoever is counting the managment port as a 7th interface on the 5515!

    Update: I just found out that you can't use the management interface for failover purposes either.     Argggggg.
    "Management interface cannot be configured for failover on this platform."

  • Sharepoint 2010 question : Error while deploying wsp file in using managment shell (power script)

    When I tried to deploy the wsp's using managment shell (power shell scripts) everything looks good.
    When I go and take a look the "manage farm solutions" thru sharepoint central admin, I see the deployment failed in two servers.
    Error is
    Could not load file or assembly 'c:\windows\Temp\solution-cxxxxxxxxxxxxxx\xxx.xxx.dll" or one of its dependencies. Access is denied.
    Can you please let me know what could be the reason.
    Note : I have two app servers and two web servers setup. The deployment is sucessful in 2 apps servers . but 2 web servers are giving error.
    Thanks
    Pichaimani

    Hi,
    According to your post, my understanding is that you wanted to failed to deploy the wsp's using managment shell.
    You need to make sure that the dll is registered in the GAC.
    Go to %Windows%\assembly. If the dll isn't there , you need to install it to the GAC on the server. Simply drag it into that folder in Windows Explorer, and it should install itself.
    Here is a similar thread for your reference:
    http://stackoverflow.com/questions/1265505/sharepoint-could-not-load-file-or-assembly-the-system-cannot-find-the-file-sp
    Best Regards,
    Linda Li
    Linda Li
    TechNet Community Support

  • Home Hub 3.0B Management interface unresponsive.

    This month (2 weeks ago) I upgraded to Infinity 2 and got a new Home Hub 3.0 Type B.
    I was able to get it all working as I wanted to - home network using 172.16.0.1/23 (because of conflicts with vpning into work which already routes 192.168./16 and 10./8)
    However, often, very often, trying to access the Hub web interface on 172.16.0.1 or via bthomehub.home simply fails to respond. Regardless of the browser, or me using telnet to simulate a HTTP call.
    #host bthomehub.home 172.16.0.1
    Using domain server:
    Name: 172.16.0.1
    Address: 172.16.0.1#53
    Aliases:
    bthomehub.home has address 172.16.0.1
    # telnet 172.16.0.1 80
    Trying 172.16.0.1...
    Connected to 172.16.0.1.
    Escape character is '^]'.
    GET /
    And it just hangs.
    Even though the web management interface is unresponsive, the internet seems to work ok, though wifi is sporadic.
    Rebooting the hub doesn't seem to help.  I read some reports of badly fitted heatsinks on these Type B's - so could mine be over heating and causing this lock up?  If I leave it and try again in a few hours it may work again.  Yesterday the internet connection dropped twice and when I was able to login to the web interface, the Event log showed that the hub had spontaneously rebooted itself.
    Do I have a bad home hub?

    Hi pgregg,
    Have you tried a full reset of the hub yet? Not just a reboot?
    Chris
    BT Mod Team.
    If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
    If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

  • How to Setup Batch Management Level (Material vs Client)

    Hi Experts,
    I had a question about the level at which I should be setting up Batch Management. The requirements that we have are:
    - We want uniqueness in the batch being created.
    - We have split valuation active at the Batch Level.
    Hence, we have nailed down to the following 2 options: 1. Client level or 2. Material level. (I know that I will not be using Plant level because we do a lot of STO's and we do not want to lose the characteristics in the Batch at the plant level. So the plant level is out of scope.)
    Client Level: Although the client level gives us the uniqueness and supports most of our requirements, my fear with going at the client level is that it is too rigid and MAY cause problems in the future. Is that true? What would be issues/ concerns that you have faced when you have had Batch Management activated at the client level.
    Material Level: If I setup the system at this level, I would like to be able to create a Batch number for a material across the entire client only once. E.g. MAT1 can have BATCH 123 only once across the whole client. MAT 2 can have BATCH 123 but the Material# and the Batch # uniqueness should be maintained thoroughly.
    I would like to try out this level but my problem is I am unable to understand and setup this level completely. I have gone through some pretty good discussion on this topic but still am unable to understand it thoroughly. The link to this discussion is (http://www.sapfans.com/forums/viewtopic.php?f=27&t=80407). If you refer to this link, it says u2013 Client/ Material Level. What does client/material level mean? Can you please help me understand it. Also, if I setup Batch management at this level, I would like the system to auto-generate numbers for me exactly as I have mentioned above. Is there a way to do so? I was trying to setup the BATCH_MAT number range object with the batch level at Material level but the system seems to always default to the BATCH_CLT level and give us numbers. Is there a way to fix the system to check the BATCH_MAT number range object and give the batch numbering per my requirements. What happens if I use the Material Level Batch management with BATCH_CLT number range object?
    Your help is highly appreciated.
    Edited by: TV_SINR on Jul 16, 2010 8:52 PM

    Check following customizing:
    Logistics General --> Batch Management --> Specify Batch Level and Activate Status Management
    If you want to change the batch level, you have to start conversion to activate the change.
    Note that you cannot reset conversion from plant level to a higher level, read the documentation for customizing of
    "Specify Batch Level and Activate Status Management".
    If you want to work with same batches for different materials, you should use "Batch unique at material level".
    Logistics General --> Batch Management --> Batch Number Assignment
    Here you can define how the system should create batch numbers.
    Best Regards, Dirk

  • Standard Asynchronous ES for Quality Management interface

    Hi,
    Synchronous standard ES is available for Quality Management interfaces under ES bundle. 
    Could you please suggest if there is any standard Asynchronous ES available for above QM interfaces like Inspection plan, Inspection results and Usage Decision.
    Br,
    Madan

    Dear Hummel
    This link required SAP ID and use less for those who do not have S User ID's.
    further more.... could you please differentiate Stand SAP QM process compare to QM process in  RDS?

  • Setting management interface WLC 7.4.121.0

    Hello.
    I have a problem setting Management interface IP in new controller 5508. I get the error "Error in setting management interface IP".I can not place a management controller IP.
    Starting IPv6 Services: ok
    Starting Config Sync Manager : ok
    Starting Hotspot Services: ok
    Starting PMIP Services: ok
    Starting Portal Server Services: ok
    Starting mDNS Services: ok
    Starting Management Services: 
       Web Server:    CLI: ok
       Secure Web: Web Authentication Certificate not found (error). If you cannot access management interface via HTTPS please reconfigure Virtual Interface.
       License Agent: ok
    (Cisco Controller) 
    Welcome to the Cisco Wizard Configuration Tool
    Use the '-' character to backup
    Would you like to terminate autoinstall? [yes]: -
    Invalid response
    Would you like to terminate autoinstall? [yes]: no
    System Name [Cisco_bf:dd:c4] (31 characters max): 
    AUTO-INSTALL: process terminated -- no configuration loaded
    Enter Administrative User Name (24 characters max): admin
    Enter Administrative Password (3 to 24 characters): ********
    Re-enter Administrative Password                 : ********
    Service Interface IP Address Configuration [static][DHCP]: none
    Service Interface IP Address: 1.1.1.1
    Service Interface Netmask: 255.255.255.0
    Enable Link Aggregation (LAG) [yes][NO]: no
    Management Interface IP Address: 192.168.10.1
    Management Interface Netmask: 255.255.255.0
    Management Interface Default Router: 192.168.10.10
    Error in setting management interface IP 
    Management Interface IP Address: 10.10.10.1
    Management Interface Netmask: 255.255.255.0
    Management Interface Default Router: 10.10.10.100
    Error in setting management interface IP 
    Management Interface IP Address: 
    Does anyone faced this issue?
    Thanks. 

    Hi,
    Try these:
    1. With the WLC, Please set flow control(in SecureCRT or hperterminal) to none. Once the changes are made, CLI will start working as usual.
     2. Another  common reason can be related to the virtual interface configuration of the controller. In order to resolve this problem, remove the virtual interface and then re-generate it with this command:
    WLC>config interface address virtual 1.1.1.1
    Then, reboot the controller. After the controller is rebooted, re-generate the webauth certificate locally on the controller with this command:
    WLC>config certificate generate webauth
    In the output of this command, you should see this message: Web Authentication certificate has been generated.
    Now, you should be able to access the secure web mode of the controller upon reboot.
    3. Try to use some diff IP address for service interface don't use 1.1.1.1.
    Regards
    Dont forget to rate helpful posts

  • WLC 5508 - Ignoring Primary discovery request received on non-management interface (2) from AP

    Hello,
    Im receving this error on my syslog server:
    capwap_ac_sm.c:1443 Ignoring Primary discovery request received on non-management interface (2) from AP
    already checked the configuration and everything seems ok. They are registered and with clients associated.
    What could be the cause?
    Thanks in advance,
    Chris

    Thanks Scott for your fast response.
    No, I'm not using LAG.
    What do you mean with separate AP Managers?
    I have one AP Manager on vlan 100 (10.100.0.25) and the Management interface on the same Vlan (10.100.0.26)
    And users use vlan 150 (10.150.0.x).
    The switch port where the AP is plugged is configured with:
    interface GigabitEthernet2/0/20
    switchport access vlan 100
    switchport mode access
    spanning-tree portfast
    On WLC I can also check the AP history:
    Last Error Occurred Reason            Layer 3 discovery request not received on management interface

Maybe you are looking for

  • Opening a meeting from the popup reminder

    In Netscape Calendar, from the popup reminder there was an [undocumented?] keystroke to open the meeting details. If I remember correctly, this was Ctrl+O. This does not work in Oracle Calendar. Nor do any other logical key strokes that I can think o

  • OC4J and Oracle forms causes ie or firefox to not respond when running form

    When I run a form in Oracle Forms 10g, I have OC4J running, and have the following displayed: E:\Windows\system32>E:\DevSuiteHome_5\jdk\bin\java -Doracle.security.jazn.confi g=E:\DevSuiteHome_5\j2ee\DevSuite\config\jazn.xml -Doracle.home=E:\DevSuiteH

  • Help me in ironport

    hello all i have cisco router 2900 this internet router and after router conected directry by asa 5540 and conetecd by ciso switch and have tmg 2010 and exchanger 2010 i plan to install ironport c170 ip for router is 192.168.1.1/24 and ip for asa out

  • Does moving average price work with multiple valuations?

    Dear All, I have activated multiple valuations: Legal, group and profit center. I have activated ML/Actual costing for this multiple valuations too. Now I have 3 price fields in material master. Could I use moving average price for some materials typ

  • VA01 userexit for PO duplication check

    Hi Experts, I have an urgent requirement regarding PO duplication check and I need to know if there is a userexit for VA01 where I can perform PO duplication check. This PO duplication check will consists of fields VBAK-KUNNR, VBAK-BSTKD and VBAK-BNA