AX To Extend Airport Extreme To Ethernet Hub & Distribute IP's?

Hi Folks,
I haven't been able to find a definitive answer about what I'm intending to do, so I thought I'd ask the experts. Here is my setup:
I have an Airport Extreme 802.11n with firmware rev 7.4.2. It's configured to support 802.11b/g compatibility out of necessity due to a few older wireless clients in the house. I've locked it down with MAC address access control, WPA2 Personal encryption and have it as a closed network to keep it out of the eyes of neighbors that might be casually browsing local wireless networks. My DSL modem has multiple ethernet ports and the Airport Extreme is configured to use it using a manually configured internal LAN IP. DHCP is running off my Airport Extreme rather than from my DSL router, but everything but the Wii has hardcoded IP's in my house. I run my iPhone, an older MacBook Pro, my wife's MacBook and a Wii off of it without any issue. My PowerMac G5 is also on it, but is dual-homed to a wired ethernet connection since the DSL router is in my office along with the base station and my PowerMac.
Now, what I would like to be able to do is set up an Airport Express in my media room, run the Airtunes optical port out to my A/V receiver's optical port and then run the ethernet port on the Airport Express to an ethernet Mini-Hub that would then distribute IP's to my A/V receiver, PS3 and Dish receiver (and eventually a Mac-Mini but that's another story for another time. ).
What I am having trouble finding any kind of real confirmation on is whether the Airport Express will allow porting out to a mini-hub and distributing IP addresses to my components in my media room so that they have internal LAN and internet access. I know the Extreme will do this, but solid info on the Express has been hard to come by. So...I'm hoping someone here will have some helpful insight.
Many, many thanks in advance for all your help and use of your brains!

+What I am having trouble finding any kind of real confirmation on is whether the Airport Express will allow porting out to a mini-hub and distributing IP addresses to my components in my media room so that they have internal LAN and internet access. I know the Extreme will do this, but solid info on the Express has been hard to come by.+
You have two options if you use an AirPort Express 802.11n
1) You can configure the device to "join" your current wireless network and tick the box in AirPort Utility setup to "enable ethernet clients". This will activate the ethernet port. The Express will act as a "bridge". Control of DHCP and NAT will be at the AirPort Extreme. In effect, the Express becomes another LAN port of the AirPort Extreme.
2) If you need a bit more wireless coverage in the area where the Express will be located, you can configure it to "extend a wireless network". It will broaden your "main" wireless network and the ethernet is automatically enabled in this setting. It is also a "bridge" in this configuration, so like above, it functions as an extended LAN port of the AirPort Extreme.

Similar Messages

Can this be done? Airport extreme connected wireless in extend mode to connect a wireless Mac Pro with an ethernet cable from the extended airport extreme..

Can this be done? Airport extreme connected wireless in extend mode to connect a wireless Mac Pro with an ethernet cable from the extended airport extreme.

This will work.....IF....you also have an Apple AirPort router configured to provide your wireless network.
In other words, you need to have two Apple AirPort routers to extend a wireless network.
When the AirPort Extreme is configured to "extend" the wireless of the "main" AirPort, it will provide more wireless coverage and the Ethernet ports are enabled, so you could connect your Mac Pro to any of the Ethernet ports and use that as a network and Internet connection.

Airport extreme (gigabit ethernet) b/g not working

I have an airport extreme (gigabit ethernet) that I use as my base in an extended network. I Have always had it in Wireless N mode with b/g compatability. the other day my speeds went from being super fast and happy to less than 1mbps. I went and plugged directly in to the airport via ethernet and got blazing fast speeds again.. I switched my radio mode to n only and wireless speeds were fast again.. switched back to b/g compatible and they are in the toilet.. is it possible for the b/g compatible antenna to just crap out? if so this is very disoncerting as I have several wireless devices in my home that operate on b/g and don't want them to be left out in the cold.
Any input is greatly appreciated.

what I did with the b/g testing was I changed the name of the base station to another name so none of the b/g devices that were connecting to it could.. and so it was only the laptop I was using to run the tests.. and still the speeds were terrible.. of course then when I changed it to "n" only mode they were fast again. so I know that my laptop was the only client connected wirelessly or otherwise to the base station when running both tests.
I am extending the network with an airport extreme base station dual band. The solution I have in place currently is to basically swap them. I Have the Dual band running as the main base station in N mode with b/g compatability, and I have the Gigabit ethernet AEBS running as the extender... so far my speeds haven't suffered at all and hopefully it will hold that way. but I still can't understand why the AEBSn would suddenly just stop providing any kind of speed when running as the base in b/g compatibility mode.

Airport Express not properly extending Airport Extreme.

I have recently bought an Airport Express (2nd Generation) to extened the coverage of my Airport Extreme. However, whenever i set the Express wifi settings to extend the network it will knock off my Extremes network. What i mean by this is the Extreme will still be on with a green light, however the wifi drops out and the only solution I have come up with after several attempts is to unplug and restart. I have tried configuring the settings, inacse of any network interference, even restoring to factory settings. I have checked for updates on both devices, i even brought in my Airport Express (1st generation) and it connects and extends the network perfectly. I have a pretty good understanding of networks and how to configure them and this is my last try at this.

So my end result is to have my Extreme Covering my house, the 2nd generation express covering my patio area, then have my 1st generation express cover my garage. This network would extend in a straight line away from my house.
Unfortunately, this will not work if you are trying to use wireless to "extend".
The reason is that Apple's "extend a wireless network" settings will only allow a device to extend the network one time. The wireless signal cannot be extended twice.
To help you visualize the way Apple's "extend" setup works, thing of the hub and spokes of a wheel. The AirPort Extreme is the "hub". Each extending device resides at the end of a separate "spoke", since it must communicate directly to the "hub"......not to another device at the end of another "spoke".
You can have multiple devices extending the network, but each one must communicate directly to the "hub".
So, the "hub"....your AirPort Extreme needs to be centrally located in the home and each AirPort Express needs to be at the end of a "spoke". It is very important that each Express is located closer to the "hub" than another Express.
My only confusion in the matter is will my 1st generation express try to extend my 2nd generation express? or try to extend the weak signal from my extreme.
Unfortunately, what will happen is that the 1st Gen Express will "join" the wireless network by picking up the stronger signal from the 2nd Gen Express. But, when it "joins", it does not "extend".....so there will be no benefit to doing this.....unless you want to connect a remote printer to the USB port on the Express or use it for AirPlay.

Airport Extreme (Fast Ethernet) + Airport Express (WDS) = disconnects

I have an Airport Express configured as a WDS, bridging a wired device (a small PC running Linux) to an Airport Extreme (Fast Ethernet). Security is enabled (WPA).
Frequently, the Airport Express disconnects from the wireless network and I have to reboot the thing by unplugging it. I have it set up to log to the PC, but I'm not sure what I should be looking for in the log.
Any guidance? I'd like to hold on to the Express, but I can't if it's acting flakey like this.

More than likely you are experiencing RF interference from other devices operating at 2.4 GHz. You can use a tool like iStumbler to see what other networks are visible in your area. Then you can configure your 2 base stations to use a channel which is as far as possible from the channels used by other networks.

Connecting 2 Airport Extremes via ethernet if my intent is to improve wireless signal in a different area of my home

Connect the second Airport Extreme via ethernet, all is good. However, question is; do I use the same Wireless name as main Airport Extreme or do I need to name is differently? And if differently, how do devices connect to the strongest signal?

Aribia wrote:
Connect the second Airport Extreme via ethernet, all is good. However, question is; do I use the same Wireless name as main Airport Extreme
Yes. If you want your wireless devices to "see" only one wireless network, specify the exact same wireless network name, security and password for the second Extreme.
And if differently, how do devices connect to the strongest signal?
If you choose to specify different names, and your Network Preferences are configured to not "ask to join new networks" your Mac will automatically switch from one to the other, but it does not do this just because one becomes stronger than the other as you move your MacBook Pro away from one and toward the other. It will switch networks when the wireless signal falls below a threshold that is not user-selectable. It will do that whether or not you specify different wireless network names.

Have new Airport Extreme via ethernet cable from HughesNet Gen4 modem. Using NetGear WN3500RP extender. NetGear asks for different names for the 2.4 and 5 GHz bands. Most of what I have read indicats extender shoul have same name as main network?

Have new Airport Extreme conneted via ethernet cable from HughesNet Gen4 modem. Using NetGear WN3500RP extender. NetGear asks for different names for the 2.4 and 5 GHz bands. Most of what I have read indicates extender should have same name as main network? How is it best to configure with the Airport Extreme router 802.11ac?

Different names for the 2.4 and 5 GHz networks are optional, but can be convenient for you to distinguish one from another. It's up to you.

Extend Airport Extreme Network via Ethernet to Airport Express

I am trying to extend a gen 4 Airport Extreme by hardwiring ethernet to a 2nd gen Airport Express and will add a second Airport Express if I can get the first one to work. I have a large network with a 24 port switch and aiport utility 6.3.2 (most recent as of this date)
First question:
When expanding my network using the hardwired Airport Express can I name the new network anything I want or should it be exactly the same as the Extreme Network. I would prefer to name it differently so I can keep track of which network my devices are acturally joining but I will be happy simply to get this to work either way.
Second question:
After repeated attempts to configure my hardwired Aiport Extreme, I get the following yellow status error:
Yellow Internet Connetion
Yellow No DNS Servers
Yellow Conflicting DHCP Range
Observation:
Many of the suggestions here and the link posted in a previous post are not based upon the most recent Airport Untility software so that may contribute to my lack of success so far. I am using the most recent version.

Even though the express was hardwired to the extreme during the set up process it was choosing to "extend" the 5 ghz network which I have activated on my extreme. I assume this is okay. It seems to be. It offered me no other option during the set up.
Both 2.4 GHz and 5 GHz bands will be extended if the extending device supports dual bands.
I configured the express by plugging it directly into the LAN port of the Extreme. Once configure, I plugged the express into my 24 port switch. It worked.
That's a good way to do things. If the Express works when connected directly to the Extreme, and doesn't when you connect it elsewhere on the network, then you know that you have a wiring or switch issue somewhere.
I choose to keep the express network name and base station name the same as those on the extreme. They worked. Since I really want to keep track of which network I am logged into, I later changed both the network name and the base station name for the express and it seems to all work under the new names.
Either will work, as long as you don't mind logging on and off of networks to switch. Most users prefer to have one "big" network. Then, they can walk a laptop from one area to another, stay on the same network and the Mac will automatically switch to pick up the strongest signal from the closest access point.
I activated the 5 ghz on the newly configured and newly named express. It seems to work.
As it should.
While configuing the express I got the error message metioned above a couple times. I kept trying the same procdure with out changeing anything and eventually it worked.
I can't duplicate that issue, but glad that things worked after a few tries.
Since my AppleTV on the second floor has difficulties connecting with the extreme, I am thinking of plugging it in to the express directly. How do you feel about this? WOuld I be better off running another separate ethernet wire off the switch?
Always the best plan to connect any network devices using Ethernet if you can. The best networks are the ones with an Ethernet "backbone". You can connect the Apple TV to the Express or the switch, whichever is easier. Personally, I prefer to connect devices to a switch if possible just to keep things simpler and make any troubleshooting easier.
This whole system with an extreme, 3 expresses, 3 appletvs, 12-14 cameras, a 24 port switch and up to 50 devices on the network at one time (computers, phones, ipads, etc, etc) works reasonably well considering the demands I put on it.
That's quite a home network. Glad that things are working. I am sure that you notice better wireless performance now with the two AirPort Express devices wired into the Ethernet backbone.
If we could get more users to set up their networks this way, most of the complaints that we get about slow wireless, intermittent connections, etc would go away.
It's not easy to run the Ethernet cable for some users, but I have yet to hear from the first user who ever regretted doing it.

Extend airport extreme network via ethernet to airport express (special case)

This question has been asked many times on the forum, and answered many times, but I have a special case and would like to know if it can be made to work.
As you can see, the issue is that the LAN port of the Extreme is not connected back to the switch, I've only connected the WAN port of the Extreme to the switch. Therefore the express doesn't get an IP over the CAT5e cable coming from the switch, and will only extend wirelessly. The reason I don't make that connection is because the switch/modem is in the basement, the Extreme is on the second floor, the express is on the far side of the first floor, and I don't want to run another cable through the house.
First question is, can the given topology be made to work?
If the answer is no, then would it work to put an additional switch on the second floor like the following?
Thanks!

That is exactly what I am saying.
Remember, the modem has only one Internet IP address that it can deliver to a router. It is the router that assigns "local" IP addresses your other devices to "share" the Internet connection.
If you connect the Modem to the Switch, then it will be matter of chance as to which device......the AirPort Extreme or AirPort Express will get the valid IP address. The "other" AirPort will not be able to connect to the network.
Bottom line.....if you have a simple modem, as you have pictured, then it must connect directly to the WAN port on the "main" AirPort router. Something like this, for example:

ATV ethernet port used to extend Airport extreme network?

Recently bought a new 52 inch Sharp AQUOS internet ready LCD HDTV. Wondering if I can use the ethernet connection off of the ATV to connect to the HDTV, and then wireless network from there to my Airport Extreme/Cable modem. Can't determine from the ATV specs that this is possible.

Thanks. Would have been nice though.

Extended AirPort Extreme Network Unable to Connect

I have two AirPort Extremes. One was set up in the basement directly to my network and is working fine. The other AirPort Extreme was set up upstairs, plugged into the same hub as the downstairs Extreme, and I followed the default setup procedure on my MacBook Pro to extend the downstairs wireless network via ethernet. You can connect to the downstairs Extreme via wireless devices no problem, but when you move upstairs into the range of the Extreme on that level, you are unable to attach to the wireless network. I can see the network, but when attempting to attach via the MacBook, the wireless indicator works for a while, then displays a "!" with no other message. On an iPhone, you are not able to connect at all.
The setup procedure in Mac OS X is very straightforward, and I accepted all defaults in the AirPort Utility to extend the existing AirPort Extreme (downstairs) network. There are no other wireless networks that may interfere.
The router in this home is a Luxul XBR-2300. The AirPort Extremes are plugged into a switch that the router is also plugged in to. Both AirPort Extremes have access to the network/internet-- if you plug a device directly to the AirPort Extreme it can get to the internet via the hardwired connection.
I've been working on this problem for two days, have returned one of the AirPort Extremes thinking it was defective, but I have the same problem.
I did the same type of setup in another home with two AirPorts and it was 'plug and play'.

Tesserax, thank you for the reply. I have commented next to each suggestion.
If both AirPort Extreme base stations are interconnected by Ethernet they should be configured for a "roaming" network. They are interconnected by Ethernet and are configured for a "roaming" network.
Setup both AirPort Extreme base stations as bridges. Network tab > Router Mode: Off (Bridge Mode). This is how they are both set up.
For each base station:
Connect to the same subnet of the Ethernet network. They are on the same switch. They are on the same subnet.
Provide a unique Base Station Name. They have unique names.
The Network Name (SSID) should be identical. They have the same SSID, exactly.
If using security, use the same security type (WEP, WPA, etc.) and password. Note: It is highly recommended that you use WPA2 Personal for best bandwidth performance. They are both using WPA2.
Make sure that the channel is set at least three channels apart from the next base station to prevent Wi-Fi interference. Initially the Apple AirPort Utility set both up under "Wireless" settings to "Automatic". Based upon this suggestion, I set the Basement Extreme manually to the first channel choices for 2.4hz and 5.0hz networks. I set the Upstairs Extreme manually to channels at least 3 channels away. NO CHANGE to the problem.
The following are the basic setup steps: I have done the following in an attempt to fix the problem, after changing the wireless channels on both units manually:
Power all the base stations down. Done.
Perform a "factory default" reset on each of the base stations. Note: You may have to perform this more than once to make sure they "stick." Done. Confirmed with rapidly flashing light on both.
Connect one Ethernet cable between the Ethernet switch to the (circle of dots) port on the basement Extreme. Connect a second Ethernet cable between the switch and the WAN port of the upstairs Extreme.
Basement Extreme: Modem-->Router-->Switch-->Basement Extreme WAN Port
Upstairs Extreme: Basement Extreme LAN Port-->Upstairs Extreme WAN Port (Prior to this change they were both plugged in to the switch via the WAN port)
Power up just the basement Extreme. Done.
Set Network Mode option to: Create a wireless network. Done. Set the Router Mode to: Off (Bridge Mode). Done. Verify that you can get Internet connectivity with network clients either by wireless or by wire connections to the basement Extreme. Verified-- can connect with no problems. NOTE: I set this up using the iPhone AirPort Utility using default settings to create a network. I then verified these settings on the MacBook Pro in the AirPort Utility. I manually set channels based upon your recommendation to set them to insure no interference, restarted, and verified that I can connect.
Power up the upstairs Extreme. Use the AirPort Utility to select it. Done. Verify that this unit has not been plugged in after reset until now. NOTE: It now shows in the AirPort Utility Network Diagram that the Basement AirPort Extreme is connected to the Internet, and the Upstairs Extreme is plugged into the Basement Extreme. Before, both were shown connecting to the Internet.
Configure the upstairs Extreme with the Network Mode option set to: Create a wireless network. (Note: Do NOT set it to "Extend a wireless network." Verified. Was set up correctly by default.
Set the Wireless Network Name, Wireless Security, & Wireless Password options to be exactly the same as that used for the basement Extreme. Verified.
Set the Router Mode to: Off (Bridge Mode). Verified. Was set up correctly by default.
Select Update and allow the upstairs Extreme to restart. Extra Step: Manually set the channel to be 3 away from Downstairs Extreme based on initial recommendation, above. Restarted the Upstairs Extreme.
Once restarted verify that you can roam with a wireless laptop or iOS device between base stations and still gain Internet access. Problem not solved.
I followed everything above exactly. Neither my MacBook Pro nor my iPhone can connect to the "Apple Network" out of range of the Basement Extreme. The network line connecting the Extremes is verified and is a good line.
Again, thank you for the very detailed response. I had pretty much tried all of the above other than plugging the Upstairs Extreme WAN directly to the Basement Extreme LAN Port and manually setting channels on both. Did I screw anything up based upon what you wrote? Any other suggestions?
Thanks,
Ken

Extending Airport Extreme 802.11ac using Edimax BR-6675

I have a brand new Airport Extreme 802.11ac which I am now using as my network hub.
I would like to extend the network, ideally using my old Edimax BR-6675nD 450Mbps 2.4GHz/5GHz .
I have configured the Edimax as a universal repeater (on 2.4GHz only, the 5GHz signal does not reach the repeater).
I seem to be able to decide whether to create a new name for the extended network or to use the same SSID as the hub uses.
When I created a new SSID for the extension I could connect to it on mobile devices, but could not get any internet access.
I have had more success by keeping the SSID for the extended network the same as on the hub, however sometimes my devices complain that there are two networks with the same name and refuse to connect. In that case re-scanning and re-connecting usually fixes the issue.
This would make me believe that the extension is not working at all, however contradicting that I find that once I can connect I am definitely receiving much better signal strength and throughput than before I added the extender.
Connecting the Edimax by ethernet and using a roaming network is not possible.
I have seen a few articles on here warning against extending networks by combining apple with non-apple products. If that really is my core issue (i.e. that this will never work reliably and I should simply bin my old router and buy another Airport) then is there any benefit of buying a second Airport Extreme over an Express for the extension ? I do not have any 802.11ac clients yet, but likely will do within the hopeful lifespan of the routers and thus would rather buy another Extreme now if it meant extending the best signal strength.
Thanks in advance

Universal repeater can be unreliable.. security is a big bugbear.. setting at the highest level with dissimilar wireless chipsets will often not work.. but it is lucky draw..
Your edimax is Ralink.. the Apple is Broadcom.. bad combo.
Try setting security down to wpa + wpa2 but that can have bad effects on the N wireless in the AE.
If you cannot wire them.. sometimes people can use EOP (homeplug) adapters and they work very well.
I do not have any 802.11ac clients yet, but likely will do within the hopeful lifespan of the routers and thus would rather buy another Extreme now if it meant extending the best signal strength.
I have not tested AC extend wireless on the Apple but I have done it on another identical pair of routers.. the results were disappointing. With range so poor on full AC speed.. the very thing you want to extend will also likely make it extend at poor speed. So the end result is ... you may as well employ a cabler and get a piece of ethernet put in properly.
BTW a second hand extreme will be a lot better than an express.. A gen5 extreme is still an excellent unit and may well have better range than the AC model. You can pick them up in refurbished store in some places or really cheap on ebay if you buy carefully.. The express is really for airplay.. if you don't need airplay you are paying more than the second hand extreme for 10/100 ethernet which will give you slow wireless.

Airport Express disconnects wired internet connection when attempting to extend Airport Extreme WiFi network

I just purchased and airport express to extend my wifi network. My base station is an airport extreme, I have one wired connection and a wifi network. When I go through the recommended steps to set up the express and "extend the network", the airport extreme will no longer connect to the internet via ethernet. I have tried various settings and can't seem to resolve the problem. Any assistance would be much appreciated.

Ok so we now have a solution to the problem. A friend of mine came round to work this out with me last night and we were able to get it working, but it is not as easy as I had hoped. Fisrtly we plugged the airport express into my router using the ethernet cable (for this I am using an Airport Express Base Station") and in airport utilities selected the airport express. In edit, we then gave the airport express a new range of IP address which did not conflict with any of the other applications that I have already assigned. We also named the Airport Express with a distinguishable name. We then waited for the changes to be registered then unplugged the Airport Express from the router. I then plugged my AppleTV via HDMI into a tv to test it and selected the new wifi network with the new Airport Express distinguishable name. I was able to watch a video that I have on my ipad directly on my tv without being connected to the internet, and was able to play Airplay presentations.
No the easiest solution, and certainly not something that anyone at Apple has talked me through in my lengthy conversations with them at Applecare.
Hope this helps.

Can't configure Airport Express to Extend Airport Extreme Wireless

I have a working Airport Extreme wireless setup running 128-bit WEP. I now have a computer in a remote part of the house that doesn't have wireless, but has a wired Ethernet port. So I was told by a knowledgeable guy at the Apple store that I can have the AExpress pick up the wireless signal, then provide through it's Ethernet port a wired connection for my computer that doesn't have wireless.
First, is this true? If not, I'll return it.
Second, this has been a nightmare, hours and hours, and I'm pretty good with understanding networks. The book included with the AExpress is a joke, it basically just says "and let the software walk you through what you want to do."
The symptom is that I configure the device and update it with all the WEP 128 key info, but the light just stays blinking amber. I've updated the AE firmware.
What are the steps for setting up what I need? I'm using an up-to-date Mini to configure ... should the Mini be connected to the Airport Extreme base via wireless? Via wired? To the Extreme? Wireless?
This is clearly a sophisticated device with lots of promise and such, but the documentation and the number of posts to this board reflect that clearly there may just be too much complexity here for most people to handle.

So I was told by a knowledgeable guy at the Apple store that I can have the AExpress pick up the wireless signal, then provide through it's Ethernet port a wired connection for my computer that doesn't have wireless.
First, is this true? If not, I'll return it.
Yes, this is true. You can extend the network wirelessly using the WDS feature of AirPort Base Stations. In turn, you can connect wireless or wired clients to the Remote Base Stations.
What are the steps for setting up what I need?
This Apple article should help explain the steps of setting up a WDS between two AirPort Base Stations: http://docs.info.apple.com/article.html?artnum=107454

Extended Airport Extreme 802.11ac - Slow Wi-Fi

Hi All..
I have a rather frustrating scenerio here and could do with a few pointers as things arn't going my way
I recently purchased two new AP 802.11ac for my home network, setup as follows: -
Sky Modem 20Mbps
IP 192.168.0.1
DHCP
Ethernet
Airport Extreme 802.11ac (Downstairs) Version 7.7.1
Static IP 192.168.0.20 - Reserved at Modem
DNS 192.168.0.1 - Not sure if this should point to modem, advice here if possible
DNS 8.8.8.8
Wirless on, secured by WPA2, also guest network
Ethernet
Airport Extreme 2010 (Downstairs) Version 7.6.4
Static IP 192.168.0.40 - Reserved at Modem
DNS 192.168.0.1 - Not sure if this should point to modem, advice here if possible
DNS 8.8.8.8
Wireless
Airport Extreme 802.11ac (Upstairs) Version 7.7.1
Static IP 192.168.0.30 - Reserved at Modem
DNS 192.168.0.1 - Not sure if this should point to modem, advice here if possible
DNS 8.8.8.8
Wirless set Extending the above network, secured by WPA2, also guest network
Ethernet
iMac 27" 2011 (Upstairs)
Static IP 192.168.0.31 - Reserved at Modem
DNS 192.168.0.1 - Not sure if this should point to modem, advice here if possible
DNS 8.8.8.8
Running OSX Server 2.2.1 (169)
So.. I understand there are many many factors here but my issues are that the iMac (Server) downloads at the expeteced rate of 19Mbps, however anything on wirless pulls around 4Mbps at best and file transfer between the iMac and Macbook Pro (Wireless) not really happening.. This is also the case for all other clients connected to the Wireless networks (5GHz, 2.5GHz and Guest).. In fact, guest network has no connection at all...
I don't think that any of my devices has the AC ability if that matters..
Further details from 'Option + Wi-Fi Icon' on Macbook Pro :-
PHY Mode 802.11m
Channel 100 (DFS, 5 GHz)
Security: WPA2 Personal
RSSI -70
Transmit Rate: 108
MCS Index: 11
I appreciate this is probably an odd setup, but any help would be appreciated..

Ok... netspeed just resolved itself across the wirless back up ro 19Mbps..
However, file transfer between the iMac and Wireless Macbook is around 5Mbps only, any ideas?
Any feedback on the dns would also be appreciated though!

AX To Extend Airport Extreme To Ethernet Hub & Distribute IP's?

Similar Messages

Maybe you are looking for