Basic Desktop and X-Over configs

Hello,
I was wondering if anyone could suggest some good links/docs for examples on configs for Desktops and Cross Overs between switches.
We're currently running 2950's in a school/lab environment.
I've seen some of the smartport macro's built in the IOS, but our network is currently a flat network and I'm trying to learn better configurations for new switch deployments.
Our basic config as it stands with only vlan 1
service password-encryption
no spanning-tree vlan 1
no cdp run
no ip http server
switchport mode access on Cross-overs only.
(from what I've read it seems if you have a dedicated workstation in a port that it should get switchport mode access as well, is that correct?)
Any info/hints/tips would be much appreciated.
Thanks.

Hello,
basically, as a rule of thumb, the ports of your switch to which you have servers connected should be set to fixed speed and duplex settings, and the same should be the case for the respective server NICs. User ports, that is, switchports to which your desktop or laptop users connect to, should be left at the default (autonegotiate) speed and duplex settings.
Since you have disabled spanning tree (for your only VLAN, VLAN 1), make sure that there are no loops in your network.
Have a look at the following document:
Configuring Interface Characteristics
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat2950/12122ea5/2950scg/swint.htm
As for the 'switchport mode access' command, you actually might want to configure that on all your ports, not only the ports connecting your switches to each other. Since you are not using any trunks, any DTP (Dynamic Trunking Protocol) packets exchanged have no use anyway.
This document also contains a lot of information on how to best configure switchports and switches in a LAN switching environment, check if that helps you:
Troubleshooting LAN Switching Environments
http://www.cisco.com/en/US/tech/tk389/tk213/technologies_tech_note09186a0080176720.shtml
HTH,
GP

Similar Messages

Apple Remote Desktop and controlling over VPN

Hi All,
I had a question about whether something was possible and if so if someone could point me to instructions/how-to on setting it up.
I have three Macs I am administering. One is an iMac that stays in the office on the network. Two are MBP's. One is always at a remote location, the other comes in and out of the office. I work remotely administering the server and the three systems. I have the latest version of Apple Remote Desktop and obviously can access the server fine. I was wondering though if there is any way besides having the person give me their IP address every time that through the VPN I can see their system, then access it in Remote Desktop just like we are on the network together? Basically they connect to the network via VPN if they are remote and I do the same thing and then access their machine.
I hope that makes sense. I went through different parts of the guide for ARD but didn't come across a method like that described in there.
Anyone with opinions? Thoughts? Chants of I'm an idiot? haha
Thanks

Yeah for some reason I cannot get this to work right. Even if I scan the 5 VPN IP's I have setup I cannot see their machines when I am connected to the VPN. I tested it the other day by connecting one of the systems to an outside internet connection, then logged it into the VPN. I then connected my own to a different source and logged into the VPN, but Remote Desktop just won't find it.
Just not sure why it doesn't work. I can see the computers on our internal network though, just not any connected via VPN.

I am going to buy a Mac desktop and want to know how to transfer all my purchases and uploaded music from my PC. How can I do this to ensure all videos and music transfer over and not just purchases?

I am going to buy a Mac desktop and want to know how to transfer all my purchases and uploaded music from my PC. I originally started using iTunes on my PC so it has everything I have ever purchased or uploaded from my own collection of music.
How can I do this to ensure all videos and music transfer over and not just purchases? Do they do it at the Apple Store or at Best Buy? help!

Move iTunes Library from PC to MAC
http://www.macworld.com/article/146958/2010/03/move_itunes_windows_mac.html
Also, See here if you need to... iTunes to an External Drive
http://support.apple.com/kb/HT1751

I am new to LR and have it set up on a Mac desktop and laptop. On the laptop, the Basic function under Develop simply disappeared. I am lost. Help.

Question: I am new to LR and have it set up on a Mac desktop and laptop. On the laptop, the Basic function under Develop simply disappeared. I am lost. Help.

It's a common issue. The Basic panel is merely hidden.
Hiding/unhiding panels is actually a feature of Lightroom but it is unintuitive - few people know it exists - so most newcomers are thrown when a panel somehow gets hidden.
Right-click anywhere in the right hand side panel area and a context menu will appear.
Click the Basic option to make the Basic panel re-appear.

Desktop appearance problem: For no apparent reason my Mac running OSX 10.4.11 imposed a mesh-like pattern over the folders on my desktop and also across the top of the screen and down the right-hand side where I have the dock. How do I remove it?

For no apparent reason my Mac (2 GHz PowerPC G5) running 10.4.11 has put a mesh-like pattern over the folders on my desktop and also a band of the same pattern across the top of the screen and down the right-hand side over the dock. (See screen grabs below.)
It doesn't affect any operations but makes folder names and drop-down menus difficult to read through the pattern.
I'm not aware of changing any settings so suspect I must have clicked on something without noticing. How do I get rid of the overlaid pattern, please?

Information about my computer is as follows:
Machine Name:          iMac G5
Machine Model:          PowerMac8,2
CPU Type:          PowerPC G5 (3.1)
Number Of CPUs:          1
CPU Speed:          2 GHz
L2 Cache (per CPU):          512 KB
Memory:          1 GB
Bus Speed:          667 MHz
Boot ROM Version:          5.2.5f1
It looks like this at the back:

Firefox has taken over almost all of my desktop and I can't remove it....

Firefox has taken over three quarters of my desktop and I can't remove it. This is irritating and I will remove firefox if this continues,
I have pictures of my daughter as my desktop and do not appreciate this.

On any windows machine use "Alt+SpaceBar" to help you move or resize the window.
Windows 7 (only) users can use WinKey+leftarrow (cursor keys) to reposition window to the left half of the screen and then you can resize or move from there with the normal methods. Works nicely if you for instance lost your window on another monitor or want to switch the window to a different monitor in use. (something to look forward to in the future as you are on Vista)
Please refer to the following article for many more tips, more complete information on how to fix, and if possibly an extension is involved in the problem.
* '''http://kb.mozillazine.org/Resizing_oversize_window'''
It is still possible to resize and move windows with JavaScript for those who lost the ability with Firefox 8.0 and above, but it involves a couple of extra steps covered in the above article.

I bought and legally own PS CS3. Installed on a desktop and the machine died completely. Downloaded a trial of CS3 from Adobe site. Went to activate and said too many activations. Activate over the phone. EXCEPT Adobe does not handle activation issues ove

I bought and legally own PS CS3. Installed on a desktop and the machine died completely. Downloaded a trial of CS3 from Adobe site. Went to activate and said too many activations. Activate over the phone. EXCEPT Adobe does not handle activation issues over the phone. Adobe doesn't care about their older products - they don't care that I spent hundreds of dollars for CS3. This is truly disgusting corporate behavior. Is there anything I can do? We aren't all rich photographers. I paid a great deal of money for this product. Is it now useless?Thank you,
James Scott

HI James please contact the Adobe Chat Team for activation issue
kindly do the mentioned steps as follow in order to get hold of chat rep of adobe
Go to www.adobe.com/getsupport
select the product as adobe creative suite - then select the issue as adobe id and sign in - and then click on still need help contact us then you will be able to find chat option and they will help you with the chat issue

I am getting blocks of black, vertical broken lines to right of cursor, around applications on desktop and over text on internet. I recently updated from OS X Tiger to Leopard on my G5 powermac. Can anyone advise how to get rid of the blocks of lines?

I am getting blocks of black, vertical broken lines to right of cursor, around applications on desktop and over text on internet. I recently updated from OS X Tiger to Leopard on my G5 powermac. Can anyone advise how to get rid of the blocks of lines?

What graphics card is installed?
Have you looked inside to see if the interior is dusty?
Is the graphics card dusty?
If equipped, is the fan on the graphics card turning?
Leopard uses the graphics card harder than Tiger, so weakness in the graphics card is more easily shown.

PLEASE HELP -- iTunes Match - multiple problems, desktop and iOS

I've been going round and around with this issue for the past couple days (yes, I've been dedicating that much time to it) and finally went to the Genius Bar today to get help and even they were stumped. Hoping someone here can shed some light on the situation. Next stop, express lane for support.
Broad Problem:
I paid for iTunes Match around 6 months ago and activated it on my desktop.     Since then, I've had nothing but problems across my desktop and 4 seperate iOS devices (3 iPhone 4's, and an iPad 3). The basic sympton on the desktop is that iTunes itself frequently freezes (Option-Command-Esc reveals "Application Not Responding") and requires a force quit.   As soon as I turn OFF iTunes Match, this symptom goes away. I can leave iTunes open for hours without any problems. As soon as I turn it back ON, then the problem comes back -- sometimes iTunes won't launch at all (crashes before bringing the UI up), and other times it's the same freeze that requires a force-quite. Quite frustrating.
On the iOS side of things, the situation isn't any better.   When I toggle on iTunes Match and then enable "Show All Music" in the Preferences of the iPhone, then I get any one of the two following scenarios:
A) The Music App simply won't load. It tries, goes to white, and crashes back to the home screen of my iPhone.
B) If I'm lucky, the Music app will launch and I can see my entire library in the cloud as intended. The problems start though when I go to actually download/play songs from the cloud. Typically, the songs will start playing but I will eventually get an error message that alerts me that there was "Problem Downloading Track". When I then go into the Download Que of the iTunes Store (again, still on the iPhone), it shows the entire list of songs that I had wanted to download and shows them at various stages of download completion -- even if they have actually completely played on the phone itself.   Sometimes they will time out and display the "problem downloading track/try again" status, and other times the progress bar sits at about 99% with a status of "Processing".
What's particularly strange about scenario B is that I've tried to download a variety of songs to different devices -- my wifes iPhone 4, my iPhone 4, an iPad, and a iPhone 4S that the person at the Genius Bar had me use as a tester.   When I tried the iPhone 4S at the genius bar, I was amazed at how fast it downloaded to the device. This had the genius bar guy wondering if it was a problem with my phone itself or with the iPhone 4 in particular.   Unfortunately he didn't have a spare iPhone 4 to test with so I had to go home and test with my wife's iPhone 4. Again, she had the same problem.   The status bar hangs at about 99% showing a status of "processing", even though I have completely listened to the track within the Music App. The same scenario happens on the iPad as well.
Okay, if you're with me so far: here's where things start to get REALLY strange....
On MY iPhone 4, when I run into problem A or B, the only fixable solution for me has been to go into Preferences and toggle OFF iTunes Match, completely shut down the phone, restart the phone, and then launch the Music App, at which point I can see the music that has loaded to my phone.    The kicker here is that even though I've turned iTunes Match OFF and completely powered down my phone, when I go into the Music app I can ALSO see my ENTIRE iTunes Match library, completely with cloud status icons.   It's as though I never turned off iTunes Match at all. In fact, I had to triple check my own preferences to verify that it was turned OFF, which it sure enough is.   I can even go and attempt to download songs, with various levels of success based on the problems above.
Now, on my WIFE's iPhone 4, when I run into problem A or B, I tried the same process in tandem with the phones side by side as I did the test -- turn iTunes Match OFF in Preferences, power down the phone, power up the phone, and launch the Music app.    However, on her phone, when this happens the Music App shows what is to be expected -- only the music that is on the phone itself.
Okay, there's a lot to digest here, but here's the synopsis: my phone and my wifes phones are behaving differently when displaying iTunes Match, with my phone appearing to completely disregard the status of the On/Off Toggle within Preferences-->Music, and my wifes phone behaving as it should, at least in terms of what it displays.   The download problems are present on each device and the iPad is also behaving like my wifes phone.
Given all of these inconsistencies and irregularities across devices and platforms -- MacBook Pro running Lion, separate iPhone 4's each running iOS 5.1.1, an iPad running iOS 5.1.1. and an iPhone 4S running iOS 5.1.1 - my suspicion is that:
A) I've got a corrupt iTunes library file residing in the cloud
or
B) iTunes Match is having a hard time reconciling my Apple ID across so many devices (possibly complicated by issue A)
The bottom line is that I have paid for iTunes Match and have never been able to use it successfully or with any predictability.
I'm wondering if anyone else has any symptoms that match any of this and/or have come across a corrupted file in the cloud and, if so, how to remedy the situation. Since it's in the cloud, I can't do anything about. I can't even see it. Most troubling.
Note:
When I went to the Genius Bar, they had me do a complete restore of the phone (not from backup) to elminate any corrupt files within the phone itself. Even that didn't solve the problem.   That's when he brought out the 4S phone to test on and we were both so shocked at how blazingly fast the songs downloaded, error-free. That phone was able to download 8 songs completely before one song downloaded to my phone sitting right next to it. Both on the same Apple Store network and both downloading the exact same tracks using my Apple ID and login.   While it's tempting to say that the 4S is faster than the 4, I don't think it's 8 times faster with download speeds over WiFi.   However, even if the speed/completion discrepancy is because the 4S is superior, it doesn't explain the mind-boggling disparity between my wife's phone and my phone -- both iPhone 4's and both running the same iOS.   Throw in the oddity of iTunes on Lion crashing whenever iTunes Match is on and this all seems to point to some corruption in the cloud that perhaps the 4S device is able to bypass...for whatever reason.
Please help. This is nuts.

Exactly same problem - any ideas - I get error message 14

How do i see my desktop and applications after a time machine restore?

What a disaster.   For reasons I won't bore anyone with, I had to end up reformatting my iMac hard drive (internal drive, I7) to get my machine working again. I have had a daily backup going (thank goodness) with my Drobo NAS drive using Time Machine. Yes, I know Apple doesn't technically support network drives with Time Machine, but anyone with a Drobo (and Data Robotics) will tell you it works great.   That's NOT the issue.
I flattened (reformatted) my machine and reinstalled Snow Leopard. I then connected to my Drobo drive with Time Machine, and searched the most recent backups and had it restore THE ENTIRE MACHINE. All applications, all documents, etc. Took about 14 hours.
I also created the same account (I think!) that I used before when I installed Snow Leopard.    However, when I reboot, my desktop looks like a fresh Snow Leopard desktop, and none of my applications or documents show anywhere. Yet, I am sure they are there, because when I went to later restore one file (Photoshop CS5), it said "this file already exists, do you want to copy over it?" I chose not to.
I feel like it must be some permissions or account thing, but for the life of me, i can't figure out where I went wrong.   It would be a HUGE inconvenience for me to truck this huge machine (and my network backup drive) into an Apple store to talk to one of their experts, so I'm hoping I can get this resolved here with your help.
Basically, I'm stumped. Anyone got any ideas?
thanks
dc

From your description, it sounds like you may have more serious issues than a simple permissions problemand that you are now dealing with a dysfunctional "Frankensystem." Nevertheless, it is usually worthwhile trying something relatively fast and simple before going on to more complicated solutions.
You have not indicated what remedies you may have already tried outside of the setup Assistant Tip, so I am assuming you have not yet tried anything.
I have never faced this precise problem before, but in other situations involving permissions issues, I have often had success doing the following:
1) Do a "Get Info" on the folder(s) with which you are experiencing issues. In your case, this is pretty well your entire restored drive, since the Applications folder exists at the root level. So go ahead and do a "Get Info" on your internal hard drive.
2) Click on the padlock icon in the lower right corner of the GI window and enter your admin password when prompted.
3) At the bottom of the window in the Sharing and Permissions section, ensure that your disk is set up this way:
system=Read & Write
admin=Read & Write
everyone=Read only
4) Click on the gear icon and choose "Apply to enclosed items" from the pull-down menu. Allow this to work through, which in the case of a whole drive may take some time.
5) Reboot the machine and log back into your home account. Hopefully, you can now see and access all the files that should be there.
If this doesn't work, your problem may lie in the fact that upon your reinstall of Snow Leopard, you created a home folder with the same name as the one you are trying to restore from your backup, thereby creating a big headache. You might have to repeat the entire reinstall/restore process, but this time creating an account with an entirely different name when you install Snow Leopard, and then deleting it after the restore from backup.
OR
If the total amount of data contained on your Drobo Time Machine backup is not yet prohibitively huge, I would suggest that the easiest and most foolproof solution might be to use a program such as SuperDuper or Carbon Copy Cloner to clone the drive to a partition on a storage device of sufficient size directly attached to your iMac. You could then reformat your internal drive and repeat the complete restore process from the Snow Leopard install disk which should then yield normal results, i.e. a fully functional home account in which everything works as usual upon login.
This will eat up considerable time, but most significantly, it is machine time, not your time!
In my experience, the entire Time Machine process is a finely tuned one that does not take kindly to tinkering under the hood or straying from the blessed path, as you have just discovered.

Replicate desktop and settings

How do I setup laptops so that when I log off my personal computer and then log onto my wifes computer, exactly the same settings, view and desktop is on my wifes computer. Its like I am basically using my other computer - exactly the same.
Thanks

Hello The Closeman,
Thank you for the details of what you’re trying to achieve. It sounds like you would like to have the same setting that are on the user account on your computer appear on your wife’s computer. I have a couple of suggestions that may help with this.
If you are just trying to transfer your settings, desktop picture, and documents over to your wife’s MacBook Pro, you may want to consider using Migration Assistant for this. With Migration Assistant, you can choose to transfer just your user account when selecting information to transfer:
Once you transfer the account, you can log into your own account on your wife’s computer. It is important to note that with this method, any changes you make on your computer or your wife’s computer after the migration will not show up on the other system. Find more information about Migration Assistant in the following links:
OS X: How to migrate data from another Mac using Mavericks
http://support.apple.com/kb/HT5872
OS X: How to migrate data from another Mac using Mountain Lion and earlier
http://support.apple.com/kb/HT4889
Alternatively, if you are using iCloud and running OS X Lion v10.7.5 or later on both computers, you can use Back to My Mac to access your computer from your wife’s computer. The following article has additional information on setting up Back to My Mac:
Set up and use Back to My Mac
http://support.apple.com/kb/HT4907
Thank you for using Apple Support Communities.
Best,
Sheila M.

My ipad will not start. It is 1 year old...I have tried holding the two buttons and nothing..I have it connected to my desktop and it will make a ding noise but nothing comes up on the screen.

My ipad will not start. It is 1 year old...I have tried holding the two buttons and nothing..I have it connected to my desktop and it will make a ding noise but nothing comes up on the screen.

Frozen or unresponsive iPad
Resolve these most common issues:
    •    Display remains black or blank
    •    Touch screen not responding
    •    Application unexpectedly closes or freezes
http://www.apple.com/support/ipad/assistant/ipad/
iPad Frozen, not responding, how to fix
http://appletoolbox.com/2012/07/ipad-frozen-not-responding-how-to-fix/
iPad Frozen? How to Force Quit an App, Reset or Restart Your iPad
http://ipadacademy.com/2010/11/ipad-frozen-how-to-force-quit-an-app-reset-or-res tart-your-ipad
Black or Blank Screen on iPad or iPhone
http://appletoolbox.com/2012/10/black-or-blank-screen-on-ipad-or-iphone/
What to Do When Your iPad Won't Turn On
http://ipad.about.com/od/iPad_Troubleshooting/ss/What-To-Do-When-Your-Ipad-Wo-No t-Turn-On.htm
iOS: Not responding or does not turn on
http://support.apple.com/kb/TS3281
iPad: Basic troubleshooting
http://support.apple.com/kb/TS3274
 Cheers, Tom

Script for Outlook 2007 to move attachments to desktop and rename attachments.

My apologies if this is in the wrong "Discussion area" if so, please let me
know where it needs to go and I will repost it.
Also, Please forgive me as I am NOT a scripter... I do not know coding, but am finding
myself in need of a script... I can copy and paste, and know enough to make adjustments
to wording as necessary, but lack the knowledge of how to write my own code. Please help me.
I currently recieve about 50 emails DAILY with attachments in each of them
within outlook on my network. I need a script that will copy the
attachments from the emails, and then paste them into a special folder
on my desktop. I would like to have the script also rename the attachments
to a date based upon when the email was received. (ex: 18OCTOBER)
To be more specific, this is what I am trying to accomplish:
There are 2 folders on my desktop called "TRUCKS" and "CARS".
Within each of those Folders are other folders named "2011", "2012", "2013", and "2014".
I receive about 20-25 emails daily going to a folder called "INCOMING TRUCKS" in
Outlook. The email always contains an attachment called "AD Form.pdf".
I need to copy this "AD Form.pdf" from my Outlook email and have the
attachment placed in the 2014 Folder of the TRUCKS folder on my desktop,
(and come next year, go to the 2015 folder...that I will create later)
Then I would like to script to Rename the "AD Form.pdf" attachment to
"18 OCTOBER.pdf" (The date I received the email)...
AND
I also receive about 25-30 emails daily going to my "INCOMING CARS" folder from my
Outlook account. The emails contain attachments called "AD Form.pdf".
I need to copy this "AD Form.pdf" attachment from my Outlook email and have the
attachment placed in the 2014 Folder of the CARS folder on my desktop,
(and come next year, go to the 2015 folder...that I will create later)
Then I would like to script to Rename the "AD Form.pdf" attachment to
"18 OCTOBER.pdf" (The date I received the email)...
I would need this script to go through all of the emails within
the INCOMING TRUCKS and INCOMING CARS folder and once complete,
give an "alert" type of message saying "Process complete!" for me
to click on an "OK" button.
I do hope that I explained this well enough to be understood.
Is there a script out there that already does this?
If so, please point me to it, as I have not been able to find it through
Google, or any other sites I have looked into (Been looking for over 3
weeks now).
If not, I am wondering if this can even be done by scripts?
Right now I am manually doing all of this work, and it takes about
20 minutes of my time away from handling other items that need my
attention. I am hoping a script can do this for me in less than 20 seconds.
I understand if for a script to work, I have to be there and open programs or folders to
make it work. If Anyone can assist, it would be greatly appreciated.
My Specifics, if needed...I have a Windows XP-SP3 Desktop PC, and I use Office 2007. This is NETWORK computer at work. The IT guy "doesn't get paid to write scripts." :(
Email me direct to: [email protected]
Thanks again for any assistance.

I am wondering if this can even be done by scripts?
Right now I am manually doing all of this work, and it takes about
20 minutes of my time away from handling other items that need my
attention. I am hoping a script can do this for me in less than 20 seconds.
Yes, this can be done with scripts, e.g. with VBScript. Script execution time should be between one and two wooshes. To save you 20 minutes each day someone will need to invest perhaps half a day to write the script, debug it, fine-tune it and document it.
As Bill Stewart suggests, this is far beyond giving you some hints. You will need to pay a consultant to create this time-saver for you.

When reverting to purchased Adobe Acrobat XI Pro point product, after uninstalling Creative Cloud Desktop (and CC-based Acrobat XI Pro), how do I eliminate request to renew my subscription?

Creative Cloud just wasn't working for me, so after several years of frustration with being abroad and not online when the program decided to require online verification, I'm ditching Creative Cloud and reverting to the purchased Adobe Acrobat XI Pro point product. However, after uninstalling Creative Cloud Desktop (and CC-based Acrobat XI Pro), it still wants to go online and check my CC subscription, disallowing use of the newly installed point product version from a several year-old ESD file (and the more recent AcrobatUpd11010.dmg file).
Anyone have an idea of how to eliminate request to renew my subscription?
If, as a journalist, I've have these issues over the past two years, including this final insult when I'm trying to get away from CC, it can't be a one-off problem. So I'd like to hear details about others who've had a similar issue with reverting from CC back to a point product or to CS.
Thanks,
Tim

Hi Tim ,
Please refer to the following link to cancel your subscription of Creative Cloud .
https://helpx.adobe.com/x-productkb/policy-pricing/cancel-membership-subscription.html
You can get in touch with Adobe Chat Support if that does not help and to get your queries resolved.
https://helpx.adobe.com/adobe-connect/kb/connect-chat-support.html
Regards
Sukrit Dhingra

I saved an application form as a pdf to my desktop and now I can't open it!

Basically, I didn't have access to a printer, so I clicked print and then it presented my application form in a new window (my browser is chrome). Instead of printing (because I couldn't) I saved the file to my desktop and it saved as a pdf. Now if try and open it with adobe it says 'Adobe could not open...because it is either not a supported file type or because the file has been damaged (for example it was sent as an email and wasn't correctly decoded) I read other posts with people having this message but not in this context.
Now I really need to print it and I can't even open it. There's no way of going back in the application process as I can't get hold of the application form online any more.
PLEASE help! This is really important and I might have managed to screw everything up for myself. I tried to open it with chrome instead and that just opens a blank page...
Sincerely, and desperately!
nmlj

Thanks for replying.
<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Draft//EN">
<HTML>
<HEAD>
<TITLE>Error 404--Not Found</TITLE>
<META NAME="GENERATOR" CONTENT="WebLogic Server">
</HEAD>
<BODY bgcolor="white">
<FONT FACE=Helvetica><BR CLEAR=all>
<TABLE border=0 cellspacing=5><TR><TD><BR CLEAR=all>
<FONT FACE="Helvetica" COLOR="black" SIZE="3"><H2>Error 404--Not Found</H2>
</FONT></TD></TR>
</TABLE>
<TABLE border=0 width=100% cellpadding=10><TR><TD VALIGN=top WIDTH=100% BGCOLOR=white><FONT FACE="Courier New"><FONT FACE="Helvetica" SIZE="3"><H3>From RFC 2068 <i>Hypertext Transfer Protocol -- HTTP/1.1</i>:</H3>
</FONT><FONT FACE="Helvetica" SIZE="3"><H4>10.4.5 404 Not Found</H4>
</FONT><P><FONT FACE="Courier New">The server has not found anything matching the Request-URI. No indication is given of whether the condition is temporary or permanent.</p><p>If the server does not wish to make this information available to the client, the status code 403 (Forbidden) can be used instead. The 410 (Gone) status code SHOULD be used if the server knows, through some internally configurable mechanism, that an old resource is permanently unavailable and has no forwarding address.</FONT></P>
</FONT></TD></TR>
</TABLE>
</BODY>
</HTML>
This is what it says - does this mean I'm screwed?

Basic Desktop and X-Over configs

Similar Messages

Maybe you are looking for