Can 6682 be damaged by connecting AM signal to PFI0?

The 6682 User Manual, page 4-2 states "Do not connect an AM signal to PFI0 when the PFI line is configured for digital operations.  This could cause damage to the digital circuitry....."
However, Knowledge Base 4E9BT88P, which addresses the issue, makes no mention of damaged circuitry.  It is implied that the worst that can happen is erratic behavior.
My question is this.  Can circuitry actually be damaged by connecting an AM signal to PFI0 when it is configured for digital operations?
Thanks,
Dale

Hello Dale,
It is hard to tell if will definitively damage the digital circuitry of the 6682, however I it is not advisable to test this.
Is there anything specific to your application that leads you to ask this question?
Thank you.
- Christian
Christian A
National Instruments
Applications Engineer

Similar Messages

  • Just brought home my IPad. I have the MIFI on and it is bringing in a signal to my IMAC but I can't get it to connect to my IPad. Any suggestions?

    I just brought my IPad home but can't get it to connect to my MIFI. The MIFI is on and working as it's sending a signal to my IMac. How do I get it to recognize the MIFI so I can go online with my IPad?

    Does your iPad see you network?  If no, are you broadcasting its SSID?

  • Can I set up to connect 2 or 3 airport expresses to have a stronger wifi signal for a larger area?

    can I set up to connect 2 or 3 airport expresses to have a stronger wifi signal for a larger area?

    Theoretically yes. It will really depend on your situation. Please review the following Apple Support article to understand what is possible with the AirPort base stations and post back with any questions or help in setting up your extended network.

  • Palm Pre 2 Unlocked GSM P102UEU some region can not connect 2G signal

    In my country, i have a problem that's my pre 2 can not connect 2G signal although it has 4 bar signal,
    It can connect Edge/GPRS but can not make call, it always drop
    when i change to 3G, it works normaly
    I don't know why, it happen some region in my country.
    i change to another sim card with other provider, it work in 2G normaly.
    what happen with my pre ???
    sorry for my bad english
    Post relates to: Pre 2 p102ueu (Unlocked EU)

    My carrier is MOBIFONE (http://www.mobifone.com.vn/web/en/). I'm in VietNam.
    when i make a call by using 2G, it's dropped but it can connect to GPRS/EDGE for data (i can check mail). it is not happens when i'm in big city (such as Ho Chi Minh City).
    That SIM card is a 3G SIM card. when 3G is actived, it works ok in all region.

  • I'm staying at my house in Peru, South America. From my PC laptop I can see my neighbor's wifi service network, but I also have my mini iPad and I can not figure out why I can't get any wifi connection from my area. Is there a setting I need to do?

    I'm staying at my house in Peru, South America. From my PC laptop I can see my neighbor's wifi service network, but I also have my mini iPad and I can not figure out why I can't get any wifi connection from my area. Is there a setting I need to do?

    Yes, I did try to go on my settings>wifi and was waiting for any wifi signals to pick up, but nothing shows up. But on my PC I get a whole list of networks to choose from. Regarding my neighbor, I already have her password that is why I was able to get it on my PC, the problem is that the mini Ipad is not picking any signal neither can it locate me when I go to maps.

  • Bought a new Ipod touch and the WiFi does not connect.  Tried Reset and total Restore, does not connect to Router on DHCP, tried Static manually and still can not get it to connect even though it registers as connected.

    Bought a new Ipod touch and the WiFi does not connect.  Tried Reset and total Restore, does not connect to Router on DHCP, tried Static IP, Subnet, Router and DNS manually and still can not get it to connect even though it registers as connected.  Using Airport for router, latest firmware, no problems with Iphone 4 or Macbook Pro or any other internet devices.  After total Restore (factory settings) tried again, showed connected to router, but does not display "check" next to router but little rotating icon even though the wifi range signal shows connected at full strength and it says it is connected.  Just can't seem to get it to generate an IP.  Any solutions other than turning it on and off again?  Not a Merry Christmas morning.

    Ok, so, a couple of things:  Denisefromwaleska and I have the exact same size/type/color iPod.  Now wishing I'd bought the black one maybe...
    Second, Airport is an Express and I have a second one that I carry with me when I travel.  Tried to connect my Airport Express to the internet and could not although the iPod did recognize the router and tried to connect to the internet for some time, unlike my previous problem.  Updated firmware on my travel router, still could not connect to the internet.  Going to try to set up a manual Static IP on the travel router here in a few and conect through it although I predict the problem will persist. Back on the Christmas Present Airport Express router, it is back in play and working fine for all devices save the iPod. 
    Thanks again for all your help, hopefully I can get a solution in place soon,

  • When using the migrate tool to migrate from windows to mac, can you use ethernet to connect the computers to each other?

    When using the migrate tool to migrate from windows to mac, can you use ethernet to connect the computers to each other? In the Migration tool, I was only given the option of choosing the computer when it appeared on the same network, and didn't see an option to connect them to each other. Even though they're both connected to the same network with a wired connection, the migration is painfully slow.

    Yes. The following quotation is from About Windows Migration Assistant
    These are the preferred network connections, in order:
    Use a CAT6-certified Ethernet cable that is in good condition to connect the Ethernet port of the PC directly to the Ethernet port of the Mac or Ethernet adaptor (USB or Thunderbolt). You shouldn't use an Ethernet cable that has any kinks in it or is missing connector tabs.
    Use CAT6-certified Ethernet cables that are in good condition to connect the Mac and PC to your home network router/hub/switch. You shouldn't use an Ethernet cable that has any kinks in it or is missing connector tabs.
    For wireless, use the fastest wireless signal possible (802.11n 5Ghz). Try to have the PC, Mac, and the wireless access point all in the same room close to each other.

  • I can't restore damaged hd to destination, i get error 254 what is it?

    I can't restore damaged hd to destination, i get error 254 what is it?

    According to MacErrors.h, an Xcode file,
    midiVConnectErr   = -254, /*pending virtual connection created*/
    if you're trying to restore via Time Machine, see Pondini's TM FAQs, for starters.

  • TS1398 I can't find my wifi name or signal or any other wifi spots and I'm right next to my wifi router box and my iPod isn't detecting my wifi router box I'm my house

    I can't find my wifi name or signal or any other wifi spots and I'm right nepxt to my wifi router box and my iPod isn't detecting my wifi router box I'm my house

    If not:
    iOS: Wi-Fi or Bluetooth settings grayed out or dim
    One user reported that placing the iPod in the freezer fixed the problem.
    If not successful, an appointment at the Genius Bar of an Apple store is usually in order.
    Apple Retail Store - Genius Bar
    Then
    Does the iPod connect to/see other networks? (you were not clear)
    Does the iPod see the network?
    Any error messages?
    Do other devices now connect?
    Did the iPod connect before?
    Try the following to rule out a software problem:                 
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Power off and then back on the router
    - Reset network settings: Settings>General>Reset>Reset Network Settings
    - iOS: Troubleshooting Wi-Fi networks and connections
    - Wi-Fi: Unable to connect to an 802.11n Wi-Fi network
    - iOS: Recommended settings for Wi-Fi routers and access points
    - Restore from backup. See:
    iOS: How to back up
    - Restore to factory settings/new iOS device.
    If still problem make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
    Apple Retail Store - Genius Bar

  • Can an Airport Express convert a wireless signal to Ethernet?

    I'm thinking this probably can't be done, but I figured I'd ask to verify.  I know the manual says the Ethernet port on an Airport Express can only be used to connect to an existing network, but can it also convert the wireless signal to a wired one?
    My Express is set to "Join a wireless network" so it essentially is extending my wireless network.  I have a receiver that has an ethernet port for internet connectivity and I was hoping to use an ethernet cable between it and the Airport Express to join my network.  Didn't appear to work.
    I also have a Netgear WNCE2001 which is a WiFi Internet Adapter used for a different device.  When I plugged that into the receiver, it was able to join the network.  I was hoping to do the same with the Express.  I have a 1st generation and it doesn't work.  Wondering if later generations support that functionality?  Thanks in advance!

    but can it also convert the wireless signal to a wired one?
    Yes, if you have an AirPort Express 802.11n and you configure it using manual setup to "Join a wireless network" and check mark the option to "enable Ethernet clients".
    My Express is set to "Join a wireless network" so it essentially is extending my wireless network.
    The "join" setting does not provide any additional wireless coverage in the area where the Express is located. But, you can connect a printer to the USB port and "enable" the Ethernet port with the 802.11n version of the Express.
    I have a 1st generation and it doesn't work. 
    If by this, you mean that you have an older "b/g" AirPort Express....then it will not do what you want.  Check the Model Number on the side of the device. If you have Model No A 1084 or A 1088, that is the older "b/g" wireless version of the Express.
    The 802.11n version is Model No A 1264.

  • Can i use my iphone connection to run ipod touch

    Can i use my iphone connection to run my ipod touch.  My ipod has more memory and i have had it for a few years.  All good apps and info on it.  Can i use the phone connection to run my ipod.  ext maps/ gps

    GPS information cannot be output from the iPhone to any other device.
    The only way to get Internet access on the iPod Touch is via Wi-Fi.  To get a Wi-Fi signal from the iPhone it must be running iOS4 and be an iPhone4.  This would also require a tethering capable data plan from the carrier.
    A simpler solution would be to upgrade to a larger capacity iPhone like the 32GB model.  Then there is only one device to be carried.

  • Query engine : Can not find DSN in Connection String

    DearSir/Madam,
    Opearating System Windows 7 Professional(32-bit).
    I am using Application, which is developed : Visual basic 6.0(32-bit), Report Writer : Crystal Report 9.2.693(32-bit) and database: Oracle 9.2.0.10(32-bit).
    ODBC Data source : System DSN created and Connection established (Based on Driver : CR ORACLE ODBC Driver 4.10 (cror818.dll))
    In windows 7 environment Data Base connectivity and data fetching also wroking fine.
    My problem is while running reports it display error as "Query engine : Can not find DSN in Connection String"
    I want run time reports.
    For your kind information, at the same time in Windows XP Professional there is no problem found and working fine.
    Kindly help me.
    Thanks and regards,
    Swarup

    Crystal Reports 9.x is not supported on Win 7. See the following wiki:
    http://wiki.sdn.sap.com/wiki/x/b4JiAw
    - Ludek

  • How to restore my ipad?My ipad say on screen CONNECT TO ITUNE.How can i do when i connect with computer.It is need itune new version.Can you sent me.I will be waiting your answer.Please help me sir.

    How to restore my ipad?My ipad say on screen CONNECT TO ITUNE.How can i do when i connect with computer.It is need itune new version.Can you sent me.I will be waiting your answer.Please help me sir.

    Check for Updates.
    http://i1224.photobucket.com/albums/ee374/Diavonex/Album%208/78d42b19fa42e8d83b5 5a65e1333373f_zpsf58bbe10.jpg

  • Hey my brother just got an ipod touch and i can't get it to connect to itunes what to i do he's really excited HELP!! :)

    hey my lil brother just got an ipod touch and its saying connect to itunes and its plugged into my computer and im at the itunes website but i can't get it to connect can anyone HELP ME??!! my mom said that she wants his ipod to be connected so that its on my itunes account so i can see if he buys anything.
                                       PLEASE HELP ME !!!
    ~Maddie

    iOS: Device not recognized in iTunes for Windows
    iPhone, iPad, iPod touch: Device not recognized in iTunes for Mac OS X
    If you  have iTunes 11 turn on the Sidebar.  Go to iTunes>View and click on Show Sidebar. You can also do a Crtl+S to show the sidebar

  • I don't have a wireless printer, and want to print things off of my iPad.  I know that I can use the iPad Camera Connection kit to connect USB devices like keyboards and I am wondering if I could do the same with a USB printer.

    I don't have a wireless printer, and want to print things off of my iPad.  I know that I can use the iPad Camera Connection kit to connect USB devices like keyboards and I am wondering if I could do the same with a USB printer.

    I don't think you can connect a printer since you won't have the printer drivers. I use FingerPrint from collobos.com to print to my non-AirPrint printers.

Maybe you are looking for

  • A method to convert an existing iCloud account to a Child iCloud Account for Family Sharing

    I do not see any method by which to convert an existing iCloud account (we have three set up for our kids, all their birthdays are set later than their actual birthdays so we could grab their actual names before they were all gone years ago) to a new

  • UNKNOWN/APPLICATION_ERROR in SOAP

    HI my interface is proxy--> XI --> soap. I post the payload from runtime. I am able to sucess full messge in SXMB_moni. but in Adapter Engine it was showing below error. MP: Exception caught with cause com.sap.aii.af.ra.ms.api.RecoverableException: S

  • The code build is "succesful" but nothing happens...

    I have a problem with the code, what it is supposed to do is get the grades inputed from the user, calculate an average and then print it. I have one marked error in the code and its the " edp.processStudents();" part. Also, when i run the code nothi

  • Email button with file variables

    I need to have a button at the end of an swf that sends an email and includes variables from the file. Is that possible? I successfully put a button that opens outlook with the To: address as I defined. But I need to add variables from the file to th

  • Lightroom Getting Started guide

    For those of you who only downloaded LR and did not get the Lightroom Getting Started guide By Adobe with the Boxed version, you can now download aas High or Low Res PDF version of it at the Adobe Photoshop Lightroom Design Center. Don Don Ricklin, M