Can DAQmx regeneration cause 200019 error

I am using a 6230 DAQ card to output a continuous analog (AO_0) tone of varying levels. The problem is that I am trying to use the same card (AI_0) to sample the data and keep getting error -200019 (Measurements: ADC conversion attempted before the prior conversion was complete). I have tried to adjust the sample rates and can't resolve the issue. Can the DAQ card sample while outputting a continuous tone with regeneration disabled?
NI DAQmx: Continuously Generate Waveform - Non Regeneration - Rapidly Updating - WEB Link: http://zone.ni.com/devzone/cda/epd/p/id/370
Matthew Fitzsimons
Certified LabVIEW Architect
LabVIEW 6.1 ... 2013, LVOOP, GOOP, TestStand, DAQ, and Vison

Is the AI being hw-clocked at all or is it a software-timed on-demand reading? Can you post a screenshot of the task config and write/read code?
I've used M-series boards for multiple simultaneous tasks before and they have typically behaved fine.
Odd question: any chance that the AO task is producing an uncaught error that ends up causing the AI error? Your setup sounds like one where
*AO* errors would be more likely due to the timing needs of updating the non-regenerating buffer. It's otherwise hard for me to picture how you'd
get the opportunity to attempt a 2nd AI Read before the 1st has finished. You don't have multiple parallel attempts to do on-demand AI Reads, do you?
-Kevin P.

Similar Messages

Photoshop CS4 for Mac What can cause the error: Plug-in failed to load - NO VERSION

With Photoshop CS4 for Mac I install the Kodak Plug-in DIGITAL GEM Airbrush Professional v2.1.0. When Photoshop starts I get an error:
Plug-ins that failed to load:
   DIGITAL GEM Airbrush Professional v2.1.0 NO VERSION - - from the file “DigitalAIRProv2.plugin”Flash:
   Connections
   Kuler
This plug-in works fine on my Mac Pro with Photoshop CS4 and OS 10.6 but fails on a new Macbook Air.
Reinstalling the plug-in did not make any difference. What can cause this error?

Thanks Chris, That was my first thought too but this same plug-in works on another installation of CS4. This is a Mac installation and the plug-in is Universal so it should work. Is there any other possible cause for this error? Would Photoshop refuse to load a plug-in in a low memory situation?
Also, The Flash extensions:Connections and Kuler are working OK, I just copied a little more out of the System Info report than I needed to.

What can be the cause of Web ADI error : Cannot execute SQL statement?

I created a custom integrator in r12.2.3 and while loading I encountered an error, Cannot execute SQL statement.
I checked my setup in Interface attribute , the RUN_ID column has a default type SQL QUERY with a default value SELECT XXCONV_EAM_ASSET_NUM_S.NEXTVAL FROM DUAL.
If I have a right setup here, what can be the cause of this error?

Hi,
The possibilities can be of various reasons, with the sql statements,
xml descriptors, data sources, improper drivers anything. To crack down
the solution, kindly let me know the error messages and what exactly are
you trying to accomplish.
Thanks & Regards
Raj
manimaran t wrote:
what may be the cause of this error java.sql.SQLException: invalid sql
type passed to callable statement in iplanet ussing JNDI
Try our New Web Based Forum at http://softwareforum.sun.com
Includes Access to our Product Knowledge Base!

TS1702 Has any one had trouble getting or giving lives in candy crush...I keep getting a message that says an error has occurred, please try later. This has been going on for two days! Can't move cause I need to be unlocked, can't ask friends because of

Keep getting message"error has occurred, please try again later". When i try to send lives or ask friends for lives. Can't play cause I need to be unlocked. Help!

Simple...
http://www.apple.com/uk/support/mac/app-store/contact/

I can't login caused of an unknown error (-9808)

I can't login caused of an unknown error (-9808) since a few weeks. I know my Apple ID and the right password...
I also can't create a new account, but the connenction to the internet is there and I can also use the itunes store with all functionalities exept the log in...
All the other desciptions of this error (-9808) and sugestions don't work. I've also got the latest version of itunes.

I've seen this before but I'm a bit unsure of these kind of things. Is it really trustworthy? But thanks anyway for the answer, I'll probably try it anyway.

What could cause "Internal error: java.lang.NullPointerException: can't not add null to SWF frame" when using compc?

using flex sdk 4.6, and air sdk 15.0.0.356
we get the following error when using compc in our ant build:
[java] Internal error: java.lang.NullPointerException: can't not add null to SWF frame
[java] at com.adobe.flash.swf.SWFFrame.addTag(SWFFrame.java:77)
[java] at com.adobe.flash.compiler.internal.units.requests.SWFTagsRequestResult.addToFrame(SWFTagsR equestResult.java:114)
[java] at com.adobe.flash.compiler.internal.targets.SWFTarget.addCompilationUnitsAndDependenciesToF rame(SWFTarget.java:398)
[java] at com.adobe.flash.compiler.internal.targets.SWFTarget$FramesInformation.createFrame(SWFTarg et.java:838)
[java] at com.adobe.flash.compiler.internal.targets.SWFTarget$FramesInformation.createFrames(SWFTar get.java:875)
[java] at com.adobe.flash.compiler.internal.targets.SWFTarget.build(SWFTarget.java:243)
[java] at com.adobe.flash.compiler.internal.targets.SWCTarget.buildLibrarySWF(SWCTarget.java:348)
[java] at com.adobe.flash.compiler.internal.targets.SWCTarget.build(SWCTarget.java:128)
[java] at com.adobe.flash.compiler.clients.COMPC.buildArtifact(COMPC.java:144)
[java] at com.adobe.flash.compiler.clients.MXMLC.compile(MXMLC.java:541)
[java] at com.adobe.flash.compiler.clients.MXMLC.mainNoExit(MXMLC.java:230)
[java] at com.adobe.flash.compiler.clients.MXMLC.mainNoExit(MXMLC.java:184)
[java] at com.adobe.flash.compiler.clients.COMPC.staticMainNoExit(COMPC.java:75)
[java] at com.adobe.flash.compiler.clients.COMPC.main(COMPC.java:62)
which seems to be rather vague, and offers no clue as to what caused the problem. so, my question is, what could cause this error?
these are the compiler options we use in the build file:
<java jar="${flex.compc.jar}" dir="." fork="true" failonerror="true">
      <jvmarg value="-Xmx512m" />
      <arg line="@{options} ${_compc.libpath} ${_compc.externspath} ${_compc.includespath}" />
      <arg value="+flexlib=${flex.frameworks.dir}" />
      <arg value="-load-config=@{config}" />
      <arg value="-source-path=@{src.dir}" />
      <arg value="-include-sources=@{src.dir}" />
      <arg value="-output=@{dest}" />
      <arg value="-swf-version=@{swf.version}"/>
      <arg value="-debug=${flash.debug}"/>
      <arg value="-advanced-telemetry"/>
</java>
assume that the properties resolve to correct values, since all projects (except one) call this task and compile successfully. the error must come from this one project that fails, but we don't know why.
any ideas?

You could be running out of memory, try increasing the -Xmx512m value to -Xmx1024m or another value that you prefer

VISA -1073807338 can anyone give me a better definition of what causes this error, other than the description provided in LabVIEW help?

I have been seeing a recurring instance of this error recently, that I am not completely understanding. Can anyone better explain what may be occurring when this type of error occurs.
Feel feel to speculate, but I was hoping maybe a designer might chime in on this.

Well, if I were the designer of the error code, I think I could probably give an idea of what kinds of circumstances might cause this error to occur, regardless of the application.
However, if it helps, here is the problem. I have an ATE program that performs thermal cycling for a UUT using VISA calls to a GPIB controller which communication with 3 different instruments. The test itself runs fine for long periods of time, and then I start to see this error occur. However, the program appears to continue to run after I press 'OK' from the pop-up dialog ackowledging that the error has occurred. There appears to be no evidence of a memory leak that could possibly be contributing to the problem, or at least none that I have detected, and the error description itself is very vague. So basically what I am looking for is a better understanding of what MIGHT be causing this type of error. I would not expect a specific cause for my particular application, because as Bob was so kind to point out, I hadn't offered much information in my original post. What I was really looking for was a better understanding of the error itself, from a 30kft point of view.
Thanks Bob_Schor for pointing out the deficiencies of my original question, it's posts like yours that make this discussion board a wonderful place to have a professional discussion.

Ask your question.Can't render get File error access denied. Whats causing this? FCP 7.0.3

I Can't render get File error access denied. Whats causing this? FCP 7.0.3

Its an was update from an earlier version.
What earlier version?
And you're saying when you using File>Import>File and select a JPEG you get the error message?
You can't or shouldn't import MP3s into FCP.
Have you try creating a new porject and importing into that?

Crystal Server 2013: How to troubleshoot "Can not create temp file---- Error code:-2147215357"

We have a Java7 web app, which generate PDF report by calling Crystal Server 2013 SP4.
The app is being deployed on many different servers. We sometimes got the error below when generating report:
com.crystaldecisions.sdk.occa.report.lib.ReportSDKException: Can not create temp file---- Error code:-2147215357 [CRSDK00000615] Error code name:internal
at com.crystaldecisions.sdk.occa.report.application.PrintOutputController.controllerExportInternal(PrintOutputController.java:280)
at com.crystaldecisions.sdk.occa.report.application.PrintOutputController.export(PrintOutputController.java:152)
at com.crystaldecisions.sdk.occa.report.application.PrintOutputController.export(PrintOutputController.java:130)
at com.crystaldecisions.sdk.occa.report.application.PrintOutputController.export(PrintOutputController.java:113)
Problem is, this seems to be a pretty generic exception. It could be caused by many different reasons.
e.g. network connection problem, wrong DB login, wrong folder path, lack of folder access right, etc.
Each time we could only guess what's wrong.
We are running into it again, and this time everything seems correctly configured so far.
We wonder if there are more info we can get to troubleshoot? For example, any log file of Crystal Server we should look into? Or does Crystal Server has debug mode which prints more details to tell us what goes wrong?

Prithviraj Shekhawat wrote:
Hi Henry,
I believe you are using RAS SDKs to export the reports to PDF.
Apply trace on RAS server and check what you find in RAS logs.
Check whether you can see timeout error is RAS logs. Usually if connection is lost and the RAS server no more have the session to write to the temp directory, we do see these errors.
Also, does the account that runs RAS have permissions to create a file in RAS's default temp directory? Are you getting any out of memory or out of disk space exceptions on App server or RAS, tracing RAS server is the way to move forward.
Thanks,
Prithvi
>>I believe you are using RAS SDKs to export the reports to PDF.
Yes
>>Apply trace on RAS server and check what you find in RAS logs.
>>Check whether you can see timeout error is RAS logs.
How to configure tracing, and where are RAS logs? Is it configured in CMC --> Servers --> Crystal Report Services?
>>Also, does the account that runs RAS have permissions to create
>>a file in RAS's default temp directory?
Pretty sure yes.
>> Are you getting any out of memory or out of disk space exceptions
>>on App server or RAS, tracing RAS server is the way to move forward.
Not on App server.
For RAS, that's the problem, I am not sure where to look.......

I am trying to install current Firefox 3.6, as I am currently running an older Firefox on my Windows ME, but I keep getting this error message: "Setup has caused an error in SETUP.EXE Setup will now close."--Please help?

I have downloaded all IP changer Privacy software I have purchased and am trying to install it, and although it is made to work with WindowsME that I am currently using on my computer, it now says it requires Firefox 3 or above to be able to install the software. Therefore, I am trying to update my Firefox to current 3.6 but once Firefox 3.6 downloads it doesn't install. Instead I just keep getting the same error message: Setup has caused an error in SETUP.EXE. Set up will now close. Several times, I have also tried restarting the computer as the error message also recommended But I just still keep getting the same error message when I try to update/install Firefox 3.5. Please help/advise on how I can fix this problem. Many thanks in advance!

Firefox 2.0.0.20 is the last ever version of Firefox for Win98 / SE / ME.
You can get it from here, but you are better off using K-Meleon (derived from Firefox) or Opera instead an old version of Firefox:
[ftp://ftp.mozilla.org/pub/firefox/releases/2.0.0.20/win32/en-US/]
You can try KernelEx to get Firefox 3+ to work, but it would be very slow with an old PC of less than 750Mhz. 3.5 and later supposedly doesn't work.
http://sourceforge.net/projects/kernelex/

A view, function and TO_DATE causing an error.

I have the following statement which calls a view, VW_DIST_RPT_WORK_LIST which in turn calls a function which returns either 'Null' or a date string e.g. '07 Oct 2003' as a VARCHAR2 (alias PROJECTED_DELIVERY_DATE).
Statement:
SELECT CUSTOMER_NAME, PROTOCOL_REFERENCE, SHIPPING_REFERENCE, CUSTOMER_REFERENCE, COUNTRY, PROJECTED_DELIVERY_DATE, STATUS, NOTES,
TO_DATE(PROJECTED_DELIVERY_DATE)
FROM VW_DIST_RPT_WORK_LIST
WHERE EXPECTED_DESP_DT IS NOT NULL
AND UPPER(PROJECTED_DELIVERY_DATE) NOT LIKE('NULL%')
AND EXPECTED_DESP_DT <= TO_DATE('07/10/2003', 'DD/MM/YYYY')
AND TO_DATE(PROJECTED_DELIVERY_DATE) <= TO_DATE('31/12/2003', 'DD/MM/YYYY') --< Problem here
I need to be able to specify a date filter on the PROJECTED_DELIVERY_DATE field and hence used the TO_DATE(PROJECTED_DELIVERY_DATE) <= TO_DATE('31/12/2003', 'DD/MM/YYYY') but this is generating an ORA-01858: a non-numeric character was found where a numeric character was expected.
I think the problem lies with the fact that this field can contain 'Null' which cannot be converted to a date using TO_DATE. I've tried adding a NOT LIKE ('NULL%') statement to catch any nulls which may be creeping in bu this doesn't solve the problem.
I've added TO_DATE(PROJECTED_DELIVERY_DATE) to the select above to determine if the nulls are being caught and if the TO_DATE in performing the conversion correctly which it is on both counts.
Any ideas anyone ?

The answer provided above by Monika will work for this situation. However, you should seriously think whether you should be using a string for date datatype. Ideally, you should rewrite the function that returns PROJECTED_DELIVERY_DATE and change the return type to DATE. The least you should do is to return NULL (instead of the string 'NULL') from the function. Oracle handles nulls perfectly, there is no reason you should write code to handle nulls;
One more thing. Looking at the type of error you are receiving, it seems that you are using rule based optimizer. Why do I think so? Because, in rule based optimizer, the conditions are evaluated in a specific order (viz, bottoms-up for AND clauses). To show this, look at the following simple demonstration. I did this in Oracle 8.1.6 (also in 9.2.0.4.0 on Windows).
-- Check the database version
select * from v$version;
BANNER
Oracle8i Enterprise Edition Release 8.1.6.1.0 - Production
PL/SQL Release 8.1.6.1.0 - Production
CORE 8.1.6.0.0 Production
TNS for Solaris: Version 8.1.6.0.0 - Production
NLSRTL Version 3.4.0.0.0 - Production
-- Create the test table
create table test (a number(2));
insert into test(a) values (0);
insert into test(a) values (1);
insert into test(a) values (2);
insert into test(a) values (3);
insert into test(a) values (4);
insert into test(a) values (5);
insert into test(a) values (6);
insert into test(a) values (7);
commit;
-- See that I have not analyzed the table. This will make use of RULE based optimizer
select * from test
where a > 0
and 1/a < .25;
and 1/a < .25
ERROR at line 3:
ORA-01476: divisor is equal to zero
-- Look at the query clause. Even though I specifically asked for records where a is positive
-- the evaluation path of rule based optimizer started at the bottom and as it evaluated the
-- first row with a=0, and caused an error.
-- Now look at the query below. I just re-arranged the conditions so that a > 0 is evaluated
-- first. As a result, the row with a=0 is ignored and the query executes without any problem.
select * from test
where 1/a < .25
and a > 0;
A
5
6
7
-- Now I analyze the table to create statistics. This will make the query use the
-- cost based optimizer (since optimizer goal is set to CHOOSE)
analyze table test compute statistics;
Table analyzed.
-- Now I issue the erring query. See it executes without any problem. This indicates that
-- the cost based optimizer was intelligent enough to evaluate the proper path instead of
-- looking only at the syntax.
select * from test
where a > 0
and 1/a < .25;
A
5
6
7
Does the above example seem familiar to your case? Even though you had the AND UPPER(PROJECTED_DELIVERY_DATE) NOT LIKE('NULL%') in your query, a record with PROJECTED_DELIVERY_DATE = 'NULL' was evaluated first and that caused the error.
Summary
1. Use dates for dates and strings for strings
2. Use cost based optimizer
Thanks
Suman

The Context has expired and can no longer be used error

Hello All,
I am getting ‘The context has expired and can no longer be used.’ error.
The last thing that was modified on the farm was Distributed Cache Service.
We stopped it on the application server and only have it run on the two WFE’s servers.
Also the cache size was changed to 2048MB.
Is it possible that this change is causing the error?
We don’t have ‘Default Time Zone’ selected for the web application.
But we never saw this error till now.
Any suggestions?
Thank you,
Zabcia

Hi Zabcia,
Thanks for posting this issue,
following could be the reason of raising this issue
1. Security context of your session might be expired
2. Somebody/you might have change the data time of your server.
you can follow below mentioned steps to fix this issue
Just change/update the Date/Time in the SharePoint server
Increase the Security context in SharePoint central admin. This can be done by following the below steps:
Go to central admin
Go to "Application management section" Go to "Web Application General Settings"
Go to "Web page Security validation" section & increase the timeout field. Or, you can simply disable this option.
I hope this is helpful to you, mark it as Helpful.
If this works, Please mark it as Answered.
Regards,
Dharmendra Singh (MCPD-EA | MCTS)
Blog : http://sharepoint-community.net/profile/DharmendraSingh

Firefox has detected that the server is redirecting the request for this address in a way that will never complete. * This problem can sometimes be caused by disabling or refusing to accept cookies.

Firefox has detected that the server is redirecting the request for this address in a way that will never complete.
* This problem can sometimes be caused by disabling or refusing to accept
cookies.

In my experience this is most of the times a server issue of the website provider.
Does this error occur on all Websites or just one specific Website?
Does this Website load in Internet Explorer (or any other Browser?)?

I frequently get the "Firefox can't find the server" error message.

I frequently get the "Firefox can't find the server" error message. Refreshing the page normally causes the page to load, although sometimes it takes more than one try.
I have checked my connection settings. IPv6 and DNS prefetching are disabled, as recommended by this article: https://support.mozilla.com/en-US/kb/Firefox%20cannot%20load%20websites%20but%20other%20programs%20can?s=Firefox+can%27t+find+the+server+at&r=1&as=s

A possible cause is security software (firewall) that blocks or restricts Firefox or the plugin-container process without informing you, possibly after detecting changes (update) to the Firefox program.
Remove all rules for Firefox from the permissions list in the firewall and let your firewall ask again for permission to get full unrestricted access to internet for Firefox and the plugin-container process and the updater process.
See:
*https://support.mozilla.com/kb/Server+not+found
*https://support.mozilla.com/kb/Firewalls

DESADV01 E1EDP07 segment per line item causes EDIFACT error

When a Sales Order has the PO Number + Date populated, the subsequent outbound Delivery IDoc (DESADV01) contains a parent E1EDP07 segment for every child line item segment (E1EDP09). For a SO without PO Date, the IDoc is created with a single E1EDP07 with multiple child E1EDP09 segments. This is standard SAP - do you need to code around this?
The first scenario causes an error in EDIFACT mapping, as a limit of 9 RFF segments is allowed (E1EDP07 is a level 1 segment). Partner systems reject this.

Hi,
Segment field should be optional, so check the posting keys in OB41, check the GL account which hit this posting and check the FIeld status in OBC4 and make the segment field as optional.
while posting the transactions you can check in more then Profit center and segment details will be updated in the postings.
try out, this might help. check the new ledger document types also.
Regards,
Padma

Can DAQmx regeneration cause 200019 error

Similar Messages

Maybe you are looking for