Can I use Airport Express to extend signal from my Airport Extreme and then run Ethernet from Express to my TV which requires ethernet to access internet?
As stated in title. I want to access Netflix but my TV requires ethernet connection. I would like to use Express to repeat Exreme sigal and then to TV via Ethernet. I only have one access point in house for cable modem so I'm using Extreme to broadcast though house. Will need to be able to input network key for Extreme secure network. Thank you.
Mike
Are both your AirPort Extreme and AirPort Express 802.11"n" devices?
If yes, you can configure the Express to "extend a wireless network" and it will provide more wireless coverage and the Etherent port will be enabled so that you can connect an Ethernet device.
This assumes that the Express is located where it can receive a strong signal from the AirPort Extreme.
Similar Messages
-
Partitioned iMac 27, Sept. 2010. Verify disc on HD2 says "corrupted, needs repair," unspecified. "Use install disc to repair." HD2 is isolated from Internet since birth. HD 10.6.8, but HD2 is still 10.6.3. Can I use the original 10.6.3 install disc to start, and then go to the side needing repair, without a problem?
Part 2: After 4 years, suddenly when HD2 is revived from sleep, it makes an Internet connection, all settings are the same, Network shows Ethernet is unplugged, but the indicator from modem shows connection. Maybe connected to first part of my question, but maybe not.
Thank you.Graham Giles wrote:
Have you seen this type of problem before? I think it could be a serious issue for anyone in a similar position.
No; but then, I've not had occasion to use TDM. I've been using firerwire drives for over 10 years, both FW400 and FW800, with no issues except a bit of instability using a B&W G3 machine.
TDM should be safe. Using cautious, manual copying of files from the Target machine to the Host machine should not result in unexpected loss of files or damage to the Target drive's directories. It should behave exactly the same as if it were an external (to the Host) firewire drive.
• I don't suppose there is anything I can do to 'put back' lost items from a separate Time Machine drive which has an up to date backup on it.
There is probably a way to do that - seems to me that's one of the reasons for a Time Machine volume.
On the other hand, if the Time Machine volume is rigidly linked to the now-absent OS on the original drive, there may be no way to effectively access the files in the TM archive.
I know that using a cloned drive would work well in this instance.
I have no experience with Time Machine, so perhaps someone who has will chime in with suggestions.
With the machine in TDM with the other machine, have you tried running Disk Utility to see if you can effect repairs to the drive? -
Can I download a file in different sessions or should it be in a single session? In other words can I pause the download of a file, shutdown/restart my system and then resume download from where I left off? Or will it start from the very beginning?
If a server supports resuming downloads then the download should continue where it left off.<br />
You can test that by simple starting a large download and wait a minute or so before pausing it.<br />
Then you can close and restart Firefox and see if resuming works.
You can set the pref browser.download.manager.quitBehavior to 2 on the about:config page.<br />
That will make Firefox ask for confirmation if you want to cancel the download if you close Firefox.
See:
* http://kb.mozillazine.org/browser.download.manager.quitBehavior -
I'm with the O2 network, which allows me access to the Cloud wifi service as part of my contract. My laptop cannot connect to this network without paying a fee.
I'd like to connect my laptop to the iPhone and allow it to share the Internet access provided to the iPhone.
Is it possible?Called Personal Hotspot:
http://support.apple.com/kb/HT4517 -
I want to extend the range of my Time Capsule, can I use Universal WiFi Range Extender, 4-port WiFi Adapter WN2000RPT?
A universal may work but reliability tends to be poor..
You are much better using another airport .. extreme or express.. even a second hand older one.
Or do not use wireless bridge or repeater.. simply run ethernet or use EOP adapters to a second WAP run independently of the main router.. it is far more reliable and far faster solution .. wireless bridge/repeater will halve your wireless speed. -
I am using garage band for the first time. I dragged and dropped a song from itunes into the program and I want to extend the length of the song by repeating the first 28 measures. I can't figure it out. Please help. I have spent several hours trying to figure it out on my own but have not been successful. It seems like an easy task. Can anyone help?
dewin1or wrote:
I want to extend the length of the song by repeating the first 28 measures.
split the region at the 28th measure
http://www.bulletsandbones.com/GB/GBFAQ.html#split
(Let the page FULLY load. The link to your answer is at the top of your screen)
then select only the first region and option-drag it to the end of the song -
Can I use the same hard drive to back up my photos and also do Time Machine backups?
I bought a 1T external hard drive today for my MacBookPro with the intentions of backing up my iPhoto library, and then deleting it to make more space on my hard drive.
I also tried and failed to install Time Capsule because my Verizon modem won't let Time Capsule run with it unless I use Time Capsule as my wireless.
That said, I want to back up my computer, and even though I copied my iPhoto library already, I have plenty of space to do a Time Machine backup as well.
Is this something I can do? Please let me know. After two hours on the phone with Apple only to learn Time Capsule was a waste of money, I'm hoping I don't need to buy another external HD yet…If you want to use the drive for both TimeMachine and storage, attach the drive and then open Finder > Applications > Utilities > Disk Utility. Choose the new hard drive from the left sidebar, and then in the main panel choose Partition.
Choose the number of partitions to be two. Click the first partition and change the size if you do not want the default half of the drive. Name the partition (such as Backups), then accept the default format Mac OS X Extended (Journaled) and the partition table as GUID. Click Apply and confirm you want to erase the drive.
Then do the same for the second partition, but of course, give it a different name.
When finished Quit Disk Utility.
Turn ON TimeMachine in System Preferences and direct it to your backup partition. -
Do I connect my airport express to my modem via the WAN port and then connect from airport express to my imac with ethernet cable? Is that how you "hard wire" the connection? Because when I do that, I still can't get online. Thanks.
What is the make & model of your modem?
You pretty much stated the correct wiring. There should be an Ethernet cable connected between the modem and the WAN (circle of dots) port on the AirPort Express base station.
Anytime you change networking hardware it is always a good idea to perform a complete power recycle of that hardware. Check out the following AirPort User Tip for details. Please post back your results. -
My system
PXI 1052 chassis
PXI 8196 RT controller
Flexmotion 7356 motion controller
Flexmotion 7354 motion controller
6259 M series DAQ
1520 SCXI
1520 SCXI
1314 SCXI frount mounting terminal block
DSM strain gage load cells
Exlar SR Brushless PM motors
Kollmorgen servo star CD series 5 drives
My objective:
I want to measure the force on the load cells with the 1520 SCXI (i.e. excite the load cell then amplify and condition its output) then I want to use this analog (force) signal as the primary feedback for my motion control system (7356 and 7354 motion controller connected to my drives and motors).
The problem:
The motion controller boards (7356 and 7354) can be configured for force feedback control via analog feedback from a load cell. However the boards implicitly expect the load cell signal to be amplified and conditioned with and external signal conditioner rather then using an NI SCXI module. Currently I’m am reading the SCXI signals via the 6259 M seriers DAQ and consequentially have no way to route the signal into the 735X boards for force feedback control. I can use softmotion to control the motors but then I loose the fast PID update rates possible with the 735X boards.
The question:
Is it possible to condition a load cell signal with a 1520 SCXI and then use it as the primary analog feedback for a 735X motion control board?
Thanks
Patrick Aubin
Ph.D Candidate
University of Washington &
VA MedicalCenter of Excellence for
Limb Loss Prevention and Prosthetic EngineeringHi GG,
Thank you for your feedback.
>create your own external circuitry to amplify the signal.>
True a few op-amps could amplify and filter the signal externally but the performance of such an amateur built system will never match the accuracy and functionality of the 1520 SCXI. That’s why we spent the $2500 for the professional version.
>One thing that you could do is to use a UMI with your motion controller and then wire your signal from your SCXI to the UMI.>
As I understand it the UMI is basically a break out connectivity interface for third party drives. After conditioning and amplifying the analog force signal with the SCXI module the analog signal isn’t available to wire into a UMI. To my knowledge the conditioned signal of the SCXI resides only in the PXI backplane (i.e. there is no physical access to the conditioned analog signal). Can you explain how the UMI could be help here.
Again thanks for your input GG.
Patrick -
I have a limited storage in iPhone so i bought 20g iCloud. how can i use this iCloud storage in my device to store music and photos?
Welcome to the Apple Community.
You could sign up for iTunes match and use iCloud photo library with optimisation enabled. The later will keep optimised photos on your device and iTunes match will let you access your whole collection and make room for newer content by removing older unplayed items. -
My daughter used her friends apple account to login on her ipad and then the mother of her friend thought it was being hacked and consequently tracked the ipad and my daughter lost all her photos. Can we get these back?
Your iOS device backup only includes data and settings stored on your device. It doesn’t include data already stored in iCloud, for example contacts, calendars, bookmarks, mail messages, notes, shared photo albums, iCloud Photo Library beta, My Photo Stream, and documents you save in iCloud using iOS apps and Mac apps.
-
On a Mac OS X version 10.4.11 and itunes 9.1.1. Can't update to itunes 10.6, Mac too old. Trying to get a previously purchased song. Can't use the purchased option under quick link - nothing shows up and won't let me purchase an already purchased song. What can I do?
If possible you need to upgrade OS X. However, what you can upgrade to is dependent on what your Mac hardware and configuration is which you have not provided in your profile.
-
I can not use CanaScan N670U with my Macbook Pro. I download Canoscan toolbox 4.1 from Cannon websit. It still keep saying "The scanner plug-in was not found". Please help
There is a solution (I'm running Snow Leopard on a Core2Duo iMac, but this problem arose when I was running Leopard on a G4 PowerBook too).
Problem:
You download the OS X driver for the scanner from Canon's site. I already had the CanoScan Toolbox (4.1) stored on an external drive.
You unzip the driver and run the VISE installer. After a search it finds your copy of Photoshop (and maybe even the CanoScan Toolbox), and you click to install on that/those location(s).
You get a couple of error messages, which you click through.
You restart your computer and try to run the scanner but you get an error that the driver is wrong or missing and the process will abort.
Solution:
BEFORE you restart, and with the installer package still open -
1. Copy the Into_CFMSupport_Login & Into_CMPrefs folders to
Applications : Canon Utilities
Applications : Canoscan Toolbox
and remove the prefix Into_ from each folder
2. Check whether the installer placed N067U_Library.shlb into the top level (not User level)
Library : CFMSupport
and if it didn't, move it there yourself
THEN restart, and try again. It worked for me (via Photoshop), but whether it will work for everyone, I don't know. -
Can I use iphone in BMW via usb interface for phone call and ipod functions
Can I use iphone in BMW via usb interface for phone call and ipod functions
Why don't you check the manual for your car or ask your dealer?
-
Can I use DVD+R disks with my MacBookPro, OS10.7.5, and iMovie 6 and IDVD 7.1.2
Can I use DVD+R disks with my MacBookPro, OS10.7.5, and iMovie 6 and iDVD 7.1.2 ???? I have always used DVD-R. I made a mistake in ordering and got 100 DVD+R . Would it be advisable to return them?
Yes, you can use them. As I recall the only concern is that they may not work in DVD players manufactured before 2002.
Maybe you are looking for
-
Re: Mifi and Charging - does this work for charging the iPad?
I found the following post on here - but it is too old for me to reply directly to it - however, this was a very good post and it worked for me and I would really like to get in touch with mikebob to see if the same thing would work for charging the
-
ICal no longer syncing with Google.
I am using Snow Leopard. Everything was fine and then poof. Error message reads: The calendar (https://google.com/calendar/etc. etc.) was not found on the server. Make sure the URL is correct." The URL is correct. I am given the options to Go Off
-
Problems installing Adobe Creative Suite 5 Design Premium
I had Adobe Creative Suite 5 Design Premium on a computer that no longer works, and now I am unable to install on the new computer. Please help
-
GWHA - argh! Can't get it to work!
I swear, if gwha had a neck I'd choke it. I'm so frustrated that I can't get this service to function. I'm pretty sure everything's configured correctly, but if I stop an agent it never gets restarted by gwha. Server: OES2, fully patched. GroupWise 7
-
ITunes 10.3.3 keeps asking my iPhone OS 5.0.1 to be restored by old back up
After the update of iTunes 10.3.3, I have been un-able to sync my iPhone 4 without iTunes asking me to restore my iPhone using an old back-up that I have on an external hard drive. Once I went ahead and restored it, but then when I went to sync them