Can MSI's Dust Removal Tech disabled?

Hi
I am new to the forum and new to the MSI family, well almost. I am getting 2X MSI GTX 670 Power Editions (OC) for SLI setup. I am soooo excited. Feel like a kiddy again!
I am fully aware of MSI's Dust Removal Tech and how it works, though could someone kindly advise if this can be disabled or not? When I say "disabled" I mean that the cards start normally without spinning at high RPM and/or in reverse?
Thanks for the info.
CTV

Quote from: Lavius on 06-October-12, 23:34:13
hello i have MSI N660 Ti PE 2GD5/OC. how can i make card more silent with dust removal thing..cuz its like jet loud when it's cleaning?
S/N of the card? also save current vbios with nvflash: http://www.techpowerup.com/downloads/2133/NVFlash_5.118_for_Windows.html
nvflash -b myrom.rom [ENTER]
then upload myrom.rom somewhere and give a link to it
Quote from: tech2198 on 08-October-12, 15:22:35
Will a more silent dust removal fan speed vbios ever be available?
I own a 7850 power edition and it sounds like a jet engine every boot up until windows loads drivers.
open new own topic

Similar Messages

MSI 670 Power Edition -- need to disable the Dust Removal

I just bought a 670 PE and I wish to disable the dust removal because, having a filtered case that's quite free of dust, it is of no benefit to me and only an annoyance (my system is very quiet, having the fan spin that loud is ridiculous).
It sounds like in the past there was a BIOS on the German website that did this, but I no longer see it there (I tried the one that is listed in the BIOS section there and it does nothing different).
Does anyone happen to have that particular BIOS? Very surprised that MSI does not officially provide this.
Also while I'm at it, has anyone solved the issue with these cards throttling when overclocked? Changing the power limit seems to do nothing. I'm pretty sure it's a BIOS issue.

Quote from: rydek on 14-July-14, 02:34:20
I run a MSI Z68 GD80 G3 mobo with i7 2600K. 16GB of Corsair Vengeance memory.
Then i read that it could be because i have a sandy bridge and it doesn't utilize PCI.E 3 correctly.
As flobelix stated before, you are limited to PCI-E 2.0 because of your Sandy CPU.
Talking about bandwidth, SLI with PCI-E 2.0 x8-x8 is the equivalent of PCI-E 3.0 x4-x4.
Not very good, but not very bad either.
Quote from: rydek
unigine valley sli - 2349
unigine valley single original card - 1718
Tomb Raider Tress FX off everything Ultra average FPS 62.7 - SLI
Tomb Raider Tress FX off everything Ultra average FPS 36.3 - Single GPU original
Your scores are ok.
With a better CPU (i7 3770K), the scores are around 2200 (single) and 3000 (SLI).
Those with higher scores have overclocked GPUs (and CPUs).
Tomb Raider is one of those few games with great SLI scaling (most of the games are not).
As you can see, you get a 70-75% boost in this game.

How can I remove a Disabled Extension not compatible with Firefox 4.0.1? I just want to remove it... I don't want to wait for a compatible update. Why can't I remove it?

When I upgraded from 3.XX to 4.0.1, it informed me that 2 extensions were not compatible and it never gave me the option to remove them. Firefox 4.0.1 disabled them and now I'm not able to remove them.
Also they were added by Acrobat Pro X (Adobe Acrobat - Create PDF 1.0) and Nokia Ovi Suite (Firefox Synchronisation Extension 7.3.4.51).
These extensions won't probably be updated unless they update the software that installed them. With this said, How can I remove the disabled extensions? Why it doesn't give me a button to remove them to start with?

I think it's not the problem of compatibility. Extensions installed into Windows registry won't have a remove button ( or it's greyed out ). For these extensions, you can have a look into these keys:
HKEY_CURRENT_USER\Software\Mozilla\Firefox\Extensions\
HKEY_LOCAL_MACHINE\Software\Mozilla\Firefox\Extensions\
If you are under a 64bit OS as I am, you may also try this key:
HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\Mozilla\Firefox\Extensions\
And you may find the registry entries corresponding to the extensions you want to remove. Just export them to a backup.reg, then delete these entries. Firefox will do the rest, but it seems that fx still leaves extensions.rdf untouched. You can also delete the RDF entries corresponding to those extensions inside extensions.rdf
cf: http://kb.mozillazine.org/Uninstalling_add-ons#Windows_Registry_extension
BUT the Wow6432Node key wasn't mentioned in the above article
I had to search the registry to find out the entry corresponding to a Fiddler2 extension, then I found the Wow6432Node key. I also saw the Nokia Ovi Suite entry beside the Fiddler2 entry.
Hope it helps.

I can't download files or videos, I get the response "The object is blocked" As far as I know I have removed or disabled all security programs

I am unable to play streaming video, and can't download anything. I have removed or disabled all of my security programs.
== This happened ==
Every time Firefox opened
== About 2 weeks ago, downloaded most recent Windows service pack

HI Phillip,
On the other I am wholly unable to download the file from either Safari or Firefox
Let's try one browser at a time. Open a Finder window. Select your Home folder in the Sidebar on the left. Then open the Library folder then the Safari folder. Move the Downloads.plist file from the Safari folder to the Trash. Relaunch Safari.
If that didn't help, from your Safari menu bar click Safari / Reset Safari. Select the top 7 buttons, click Reset.
Now launch Firefox. From the Firefox menu bar click Firefox / Preferences then select the
Advanced tab then the Network tab. Click: Clear Now.
Relaunch Firefox.
If nothing above has helped either browser, login to your Mac to another user account. Try Safari there. If you can't download files from Safari there, then it's a system wide problem. Boot from your install disc. Run Disk Utility to verify and if necessary, repair any errors on the startup disk.
Help here for Disk Utility: The Repair functions of Disk Utility: what's it all about?
Carolyn

How i can delete a add ons are disabled and have not remove botom ?

how i can delete a add ons are disabled and have not remove botom
http://dl.dropbox.com/u/10490895/screenshot-73.jpg
[http://example.com http://dl.dropbox.com/u/10490895/screenshot-73.jpg]

'''Ctrl+Shift+A''' should also open the Addons Manager.

I have an iMac on OSX 10.7.5 with Safari 6.1.6. Opening Safari produces a popup that cannot be removed, thus disabling everything else. How can I eliminate this?

I have an iMac on OSX 10.7.5 with Safari 6.1.6. Opening Safari produces a popup that cannot be removed, thus disabling everything else. How can I eliminate this?

Launch Safari with the Shift key held down. If that doesn't work, temporarily disconnect the computer from the Internet.
(124400)

My ipod is disabled what can I do to remove that?

My daughters ipod got disbaled what can i do to remove that

Disabled how? Cannot remember her passcode? See:
Locked Out, Forgot Lock or Restrictions Passcode, or Need to Restore Your Device
1. iTunes 10 for Mac- Update and restore software on iPod, iPhone, or iPad
2. iPhone, iPad, iPod touch: Wrong passcode results in red disabled screen
3. iOS- Understanding passcodes
4. What to Do If You've Forgotten Your iPhone's Passcode
5. How to Recover Forgotten iPhone Restrictions Passcode | The iPhone and iPad
6. Restoring iPod touch after forgotten passcode
Forgotten Restrictions Passcode Help
1. How to Recover Forgotten iPhone, iPad Restrictions Passcode

Dust Removal Technology - how to disable?

Hi,
I'm owning MSI N670 PE 2GD5/OC.
I'm happy with it, but after every restart the fans speed up to 100% and it's very annoying.
I know it's caused by Dust Removal Technology.
Aren't exist or does MSI planning to release BIOS without Dust Removal Technology fans speed up?
Maybe the best solution would be release some utility or integrate it to some utility to manually activate this feature.
It's great future, but I think it's activated very often...

I obtained a BIOS from German MSI site you've mentioned which reduce backward fan speed only to 30% in DOS.
The BIOS is dated on June 2012.
But newer BIOS was realesed from November 2012 when is stated:
"This bios is used to solve motherboard compatible issue. If your card is Hybrid bios and face this issue, please update your BIOS."
I have ASUS P8Z77-V LE PLUS motherboard.
Do you think I will not have any issues with my motherboard or in the future with Windows 8 and beyond with this German BIOS from June?
I'm not owning the card yet, so this is very important for me.
Thanks.

A10: remove or disable 3g-card

Hello.
We are preparing a roll-out of Tecra A10 at several sites.
At some sites, we like to remove or disable the build-in 3g-card (Modell F3507g).
For disabling the fingerprint-sensor we are using a very old version of tsuruwin.exe, but I do no see how to disable the 3g-card. Queries for a newer or better version were not answered by our toshiba-sales-guy but its only 4 months so I just have to wait a little longer.
If the sales-guy does not respond, what are the options here?
How can it be physically removed (and reinserted 3 years later when the lease is up?)
Or is there a software solution? Not installing the driver is not an option because of our environment, for example we are allowing and supporting toshiba-unsupported operating systems, but some scripts do not behave well with a second "wired" local area connection (as windows calls them).. The scripts do work with one wired and unlimited "wireless" (as windows calls them).
Yes, because of the pre-existing scripts I can "fail" the A10, that may cause some red faces but at least my backside is covered by papertrail.
Thank you & bye.

Totty1973, you stated that not disable the driver allowed as an option. Appears since you have a commerical sales order, best to consult with Toshiba tech support direct so as not to void the warranty naturally, and gain their workaround to meet business needs basedon server and software configurations. Best for your paper trail and less stressful for your position.

GTX 670 PE OC - need BIOS with reduced dust removal fan speed

Hi,
I'm looking for someone who will be pleased to reduce or stop dust removal fan speed after restart.
Would like to modify latest BIOS with UEFI support.
There was a BIOS which was removed from German MSI site.
I can provide it if necessary.
I'm willing to give some reward for the effort.
Thanks.

Quote from: Svet on 08-October-12, 20:02:39
Oki, reflash to attached VBIOS.
[boot from bootable USB key to perform the flash]
Flashed and now much quieter at boot.
Many thanks for your help Svet, you guys are amazing.

Can no longer add / remove to bookmarks / reading list since ios 6 upgrade

Hi all,
I upgraded my ipod touch to ios 6 last night, and since the upgrade I can no longer add / remove bookmarks or add / remove items to the reading list in safari.
Whenever I try I get the 'Bookmarks are being synced. Please edit the bookmarks once syncing has completed.' message.
So far I've tried;
A hard reset
Turning off Safari in the icloud settings
I still can't do anything with the bookmarks / reading list, I just don't get the 'Bookmarks are being synced' message
Ensuring that push notifications are enabled for icloud
I'm not sure what to try next.....
When I disable Safari in the icloud settings, it asks me if I want to keep a copy of previously synched bookmarks on my ipod - So far I have as I don't want to lose them.
I'm guessing the next step is to not keep a copy and hope ios wipes them - If I do this will the bookmarks still be available in icloud when I turn safari data back on?
Cheers
Macca

I actually managed to fix it! But unfortunately I don't know what I was that I did that helped.
Anyways, this is kind of what I did.
1. I tried to reset form bakup via iTunes, no change.
2. I tried to reset as a new iPhone, problem still there and reading list also as bookmarks!? (several hundred)
3. Noticed that I could delete a bookmark, once in a while, the other times I got the 'Bookmarks are being synced. Please edit the bookmarks once syncing has completed.' message.
4. Because I figured that it was a memory problem, I thought it made sense to delete as many as possible, witch I did.
5. Noticed that it was more likely that I coould delete a bookmark if I restarted Safari.
6. Notice that it was even more likely that I could delete a bookmark if I turned the Safari sync with iCould off (with option detete information on iPhone) and then back on again.
7. When I was about half way through deleting the bookmark list I suddenly discovered that all but one of the items in my reading list was 'waiting' and one was downloading. I kind of was 'unstuck' now.
8. I started to delete items in my reading list, but every other time I got the 'Bookmarks are being synced. Please edit the bookmarks once syncing has completed.' message.
9. It took a while to delete all bookmarks and items in the reading list.
Hope you guys could use the info here to fix your problems too!

How can I erase (or remove) the hard drive from a dead Time Capsule?

How can I erase (or remove) the hard drive from a dead Time Capsule?

I found this having had the same problem...
http://forums.macrumors.com/showthread.php?t=553818
Having removed the hard drive I'm finding I can't reformat it. I manage to mount the HD but Disk Utility crashes when trying to format (HD attached to Mac via Newer Tech. SATA cables to USB) and causes what I think is a kernal panic on my Mac which hard crashes. I see 3 partitions when attempting to mount one of which is AFP. Anyone got any ideas about how to do this? I've dug around but the only progress I've made is to note others have had to work around ACL's when replacing the logic board of the TC. Not sure if this even relates to the problem. However the tool for doing this seems to have been removed from SL. (Forum references to this procedure all relate to 10.5).

Lenovo Energy Management - Where is my Dust Removal button?

Hello. After installation my Windows 8.1 which i downloaded from Microsoft DreamSpark i installed all drivers from a CD which came with my laptop in a box.
I installed Lenovo Energy Management and I had button to remove dust. After updating my system via WindowsUpdate this button dissapeared. It's gone.
My laptop is Lenovo G500s (without touchable screen).
Anyone had same problem like me?
I want to emphasize that after fresh installation of Win 8.1 without any uptates (Windows 8.1 Pro - Build 9600) i had that "remove dust" button.
Sorry for my bad english spelling but I'm from europe. Hope you forgive me.

hi lyczewskiand,
Welcome to Lenovo Community Forums!
If this is the Dust removal that you are saying.
If your system is Windows 8.1
Open Control Panel / Uninstall a program and uninstall the Lenovo Energy Management that is currently installed.
Now try and install this version
Lenovo Power Management
Check if this can be found on this version
If not can you post a screenshot of what showing up on your end.
Thanks,
Regards
Solid Cruver

Remove GrantSendOnBehalfTo disabled user accounts - A novice at scripting

Hello. Can anyone help please
In our exchange 2010 environment we have users who are granted send on behalf to access. Obviously some users leave and I m finding that there are ghosts left behind which are causing issues with our team who add users into the grantsendonbehalfto
option using the EMC. Using the log view we coy out the command and then remove the disabled user from the command and then paste this into an Exchange Powershell command line. This wrks because it is doing what Exchange EMC does which is rewrites
the -GrantSendOnBehalfTo option in it new entirety.
The problem occurs because I need to remove these en-mass from approx 700 plus accounts.
I have tried to modify one user in order to get the script to work but it doesn't.
This is the error message that happens when I run the script below against a known account with at least 2 disabled users in:-
Couldn't find object "xxxxxxxx.xx.xxxxxxx.xxx.xx/DisabledUsers/2013-08/Gaynor Collins-Punter". Please make sure that i
was spelled correctly or specify a different object. Reason: The recipient xxxxxxxx.xx.xxxxxxx.xxx.xx/DisabledUsers/2
13-08/Gaynor Collins-Punter isn't the expected type.
+ CategoryInfo : NotSpecified: (:) [], ManagementObjectNotFoundException
+ FullyQualifiedErrorId : F6498844
+ PSComputerName : ex02-0029.xx.xxxxxxx.xxx.xx
Am running the script from my local PC
This is the script I have used.
# Gather info use get-mailbox -resultsize unlimited$mailboxes = Get-Mailbox zplew1
Foreach($mailbox in $mailboxes)
for($i = ($mailbox.GrantSendOnBehalfTo.count)-1; $i -ge 0; $i--)
$address=$mailbox.GrantSendOnBehalfTo[$i]
$addressString=$address.addressString
If($addressString -like "*disabled*")
$mailbox.GrantSendOnBehalfTo.removeat($i)
$info >> "C:\Scripts\grantsendonbehalfto.csv"
$mailbox |set-mailbox -GrantSendOnBehalfTo $mailbox.grantsendonbehalfto
}If you requiere any more info please let me know.

#1 - I recommend posting in xchange forum fo rhow to do this
#2 - Wen an account is disabled most on the information in the object is hidden. YOu would need to undelete to use the object.
#3 - Get list as text and validaye al values are not deleted accounts. Remove deleted and save back.
¯\_(ツ)_/¯

Is there a way to remove or disable the "Clear List" button from the downloads list?

Is there a way to remove or disable the "Clear List" button in the downloads list? I like to _keep_ my list populated with what I've downloaded but occasionally end up with it getting clicked on accident and lose the whole thing. Given that "Tools > Clear Recent History" dialog can accomplish the same thing I find Clear List to be irritating. So can I get rid of it in any way?
== This happened ==
Just once or twice
== my brain lapsed on me ==
== User Agent ==
Mozilla/5.0 (Windows; U; Windows NT 5.1; en-US) AppleWebKit/533.4 (KHTML, like Gecko) Chrome/5.0.375.70 Safari/533.4

Hello Chris.
# go into ''Help > Troubleshooting Information...''
# click ''Open Containing Folder''
# in the folder that appears (new windo in windows explorer), go into the folder ''chrome''
# open the file ''userChrome.css'' with a text editor
# at the end of the file, in a new line, add the following code:
<code>
button#clearListButton
</code>
I haven't tested this, but it should work flawlessly. You can always erase this line if you want the button back. This will only work on your Firefox profile. If you want these changes to span across all Firefox users on your computer, please tell me.

Can MSI's Dust Removal Tech disabled?

Similar Messages

Maybe you are looking for