Can't get WDS Relay mode to work.

I'm trying to create a wireless network between 2 houses across from one another. Basically, I want to use a SlingBox to access a DirecTV receiver attached to a large satellite dish. I have 3 new Airport Extreme 802.11n base stations and if I could get them linked together this should work really well. One base station in my current house, one in my old house connected to the SlingBox, and one somewhere in between acting as a relay.
I've tested this set-up with the 3 base stations in one room and I just can't get it to work. No matter what, the base station that's set to WDS Relay always has a blinking amber light. The main base station and the remote base station both have green lights. Also, once relay station has a blinking amber light, I can hardly ever access it from the Airport Utility. I usually have to completely reset it and start all over again. When I have been able to access it, the error messages have been either a WDS error saying no peers can be found or an "Ethernet Unplugged" error, even though I have it set to participate in a WDS network.
Has anyone been able to set up a network using an airport base station set to WDS Relay yet? If I can't get this to work, will I get the same results just using an extended Airport network rather than a WDS network, setting the 2 additional base stations to extend the network?
Thanks,
Steve
MBPro Core 2 Duo Mac OS X (10.4.8)

Oh, and how do you like the SlingBox? Are you
running the Mac OS version?
I love my Slingbox, which is running the MAC OS version ......but
It was working fine until I swopped my D-Link wireless router for an Airport Extreme. My Slingbox was reaching my WLAN via the ethernet port of an Airport Express, but since "upgrading" to a X-modem and Airport Extreme set up I have hit trouble.
I can set up the Airport Express to join the Airport Extreme WLAN (e.g. for Air Tunes), but not to extend the network.
If I try to set up the Airport Express from a factory re-boot to extend the network with Air Port Utility, it just seems to crash the Airport Extreme.
Alternatively if I try to change the setting on the Airport Express with Air Port Utility to "participate in a WDS network" I get the error message "WDS requires multiple base stations. Please add at least one WDS peer" and I don't understand what that means.
BTW, my Airport Extreme is set up with "allow this network to be extended" checked.
Airport Express & Airport Extreme don't seem to be altogether compatible.
Any and all assistance will be gratefully received!

Similar Messages

Can't get Target Disk Mode to work with host computer

Here's the problem. My Powerbook G4 went down a week ago (it's 7 years old) and I suspect the problem is either the hard drive or the portion of the logic board controlling the drive. I also have a Power Mac G4 400 that's running OS 10.4 Tiger. I've been trying to extract some files (that I failed to back up) from the Powerbook via Target Disk Mode using the older Power Mac as the host, however the target disk doesn't show up on the host screen. When I boot up the Powerbook holding the T key, it chimes and the FireWire symbol shows up like it's suppose to, but that's as far as goes. I plan on upgrading to a newer Mac, which would probably work better as a host, but money is a bit tight right now. Any suggestions would be appreciated.

If the trouble with the Powerbook is either a failed hard drive or a failed hard drive controller, FireWire Target Disk Mode isn't likely to work with any host computer. What you may want to try is installing data recovery software on the desktop G4 and seeing whether it can see the Powerbook's drive (connected in FWTDM) even though it won't mount. Data recovery software is often able to salvage data from drives that won't mount normally; it may be able to do the same thing via FWTDM.
These three DR utilities are all available in free downloadable demo versions that will show you what the full version would be able to recover before you have to pay for anything:
Data Rescue
FileSalvage
VirtualLab
Good luck.

Can't get Dual Channel mode to work

Hello,
I have a pair of 512MB DDR400 ram sticks (listed in my sig).
The Memory Slots are arranged like this:
1 2 3
[cpu] | | |
I put each stick in slot 1 and 2 and no workie, still Single Channel Mode.
I put a stick in slot#2 and #3, no workie.
I put a stick in slot#1 and slot#3, no workie.
Is there something else that I'm missing or did I just buy the wrong memory for dual channel operation? It was not a matched set, but it is the same no-name brand of memory I bought from newegg.com. They both have the same 3225804T-5 marking on them...
They are supposed to be 2.5CS and that is what my bios is set to. I don't have any special settings in the bios that I know of..
Let me know if you have any ideas or if I need to post more information.
Thank You!

K7N2-V
Not sure about this but is that motherboard based on the Nvidia nForce2 400 chipset?
What does the manual specs say?
If it is then it doesnt have 2 memory controllers and can only do single channel.
Edit: http://www.pcper.com/specs.php?p=MB&id=38
That your mobo?

Can't get my audio clip to work in Keynote except in edit mode. I've followed Help instructions to the letter. Any suggestions?

Can't get my audio clip to work in Keynote except in edit mode. I've followed Help instructions to the letter. Any suggestions?

Hi Gary - thanks so much for your help. I'd already done that, but finally stumbled across the answer for my situation. I'm new to iMac and this is the first time I used Keynote, so maybe this info will help someone else along the way - I still haven't found this in any of the Keynote documentation or forums I've read.
My slides were all set up with at least one text box in which the text was animated. The sound was the last thing I added to each slide, exactly following the info in Keynote Help re: adding audio. The audio would work when I tested it in Inspector mode, and also if I switched to soundtrack instead. But not if sound was added to each individual slide. Hmmm. After I submitted the question above, I was running through the (auto) slide show one final time to check text, animation, etc. when I noticed that on just one single slide the sound effect came through, but at the very tail end of the slide. Hmm again. Why?
Through trial & error, the answer was in the animation section - not very intuitive re: audio. The steps to correct the issue were: 1) click on the sound icon embedded in each slide, 2) click on the animation tab in Inspector. 3) There's a drop-down menu there that allows you to reposition the audio clip to the #1 spot (if it was added after other "animation"). This allows the sound to begin before the text animation begins on each slide. Before doing this, I guess the sound was in there but the slides were transitioning before it had a chance to play.
Since this is the first time I've used Keynote and it's the most recent version, I'm not sure if this is a new feature to allow users to choose where within a slide to play a sound effect, but I'm guessing that might be why was unable to find any info on how to solve it. Hopefully this will help others who get stumped.
Thanks again for jumping in to help! I really appreciate it.

AirPort Time Capsule. Read everything and tried everything. Can't get a guest network to work. Switched from bridge mode and still doesn't work. Anyone able to set up a guest network?

AirPort Time Capsule. Read everything and tried everything. Can't get a guest network to work. Switched from bridge mode and still doesn't work. Anyone able to set up a guest network?

I had a bright house cable modem that also had built-in wi-fi.
Don't mean to be picky here, but if the "modem" had built in Wi-Fi, it was not a modem. It was a modem/router, also known as a gateway type of device.
A device like this combines the functions of a separate modem and separate router in one package. Turning off the wireless on a device like this does not make a it modem.....it is still a modem/router or gateway with the WiFi turned off.
I think that if I have them replace the current "complicated" modem with a "simple" one I should be able to get the guest network up and running.
That would be correct. Hopefully, they offer this type of option for their customers.

After I exported a PDF to a Word doc and downloaded it, I can't get the pointer tool to work.

After I exported a PDF to a Word doc and downloaded it, I can't get the pointer tool to work. When I click on the document text, the only tool is the "move" tool. I can't edit or select text. Please advise.

Version of Adobe: Adobe ExportPDF (not Pro)
Operating system: Windows 8.1
Steps I am taking: When the PDF file is selected and opened, I clicked on Tools menu on right side of the screen; then I clicked on Select PDF file; then under Convert To, I selected Microsoft Word (*.docx); then I hit the box below that; and clicked Convert. I then see the message that says it is Converting to Export PDF Online. Then I see a link below that, that says Download Converted File. This takes me online to Adobe Acrobat .com, where, I see the command, Export PDF, and see a blue box on the same screen that says Select PDF Files to Export. I click on the thumbnail of the file I want to export. This brings up, online, a screen containing the file I wanted to convert to Word. Then, on the same screen, I click on the icon on the right hand of the screen that says Download. then I click on the box on the bottom the screen that contains the Word document I had wanted to convert. This brings up the Word doc. in Compatibility Mode the latest Word version, which I am unfamiliar with and which has a Picture Tools tab that I cannot escape from and I cannot get any selection tool other that the Move pointer, and I cannot find the Select text pointer to select any text on the page. I don't want this Word version and do not know how to return to the old version of Word that I am familiar with.
Can you help me, please?
Theresa Julia Schuer

How to get Motion Tracking Mode to work?

How do I get "Motion Tracking Mode" to work? I click the icon and nothing happens, its like greyed out.

scouterbsa
Here is my check list for you to review regarding using Motion Tracking Mode in Premiere Elements 10 on Windows 7 64 bit.
1. You need a video and with enough motion in the object in it to track it. Color contrast between the object and its background can be important to success.
I created a DV AVI 4:3 in which I have a circle moving, and I have used a butterfly Clip Art from Premiere Elements 10 to track to track the circle as it moves in the video. In this example, you see the object only at 0 time.
2. Select/highlight the clip on the Timeline. And then click on the Motion Tracking Mode icon above the Timeline.
You should next see the following Motion Tracking dialog asking for a Yes or No to the question "Run
Auto-Analyzer to track moving objects?" Click No.
3. At this point, you will see a bounding box on screen. That bounding box should be placed using the mouse cursor on the object
that is going to be tracked, in this case, the circle. Resize and position the bounding box accordingly.
4. Once you have the bounding box on the object and resized, click on Track Object at the top right of the monitor.
The screenshot below shows only the before clicking Track Object at the top right of the monitor.
When that action is finished the bound box edges will be an orange yellow color. I have skipped over a screenshot
for the latter.
5. With the orangel yellow bounding box in place, next drag the Clip Art (in this case, Butterfly 02) from the Clip Art display area toward and into the orange yellow bounding box frame. The orange yellow bounding box frame will turn blue. That is the first sign of success.
Hit the Enter key of the computer main keyboard and watch the results. The Butterfly should track the circle's
movement in the clip. The duration of the clip and the continuity of the object's motion in the clip can be other factors.
If you do not succeed, try again with a different video clip (one with more movement and color contrast.
The above is a best case scenario. If it is speech bubbles that you are having problems with as well, we will deal with them next.
Right now it seems like you are having problems getting started rather than having a problem with a specific Clip Art that you are
using to track the object in your video.
We will be watching for your results.
ATR

How can I get the right click to work in firefox -- it works in internet explorer

how can I get the right click to work in firefox -- it works in interne

Try the Firefox SafeMode to see how it works there. <br />
''A troubleshooting mode, which disables most Add-ons.'' <br />
''(If you're not using it, switch to the Default Theme.)''
* You can open the Firefox 4/5/6/7 SafeMode by holding the '''Shft''' key when you use the Firefox desktop or Start menu shortcut.
* Or use the Help menu item, click on '''Restart with Add-ons Disabled...''' while Firefox is running. <br />
''Don't select anything right now, just use "Continue in SafeMode."''
''To exit the Firefox Safe Mode, just close Firefox and wait a few seconds before using the Firefox shortcut (without the Shft key) to open it again.''
If it is good in the Firefox SafeMode, your problem is probably caused by an extension, and you need to figure out which one. <br />
http://support.mozilla.com/en-US/kb/troubleshooting+extensions+and+themes

How can I get the readability bookmarklet to work

Firefox 3.6.8 in Windows XP Home on a Toshiba netbook. How can I get the "readability" bookmarklet to work? It works just fine in Camino on an Apple mini desktop computer running OS X 10.4.11 (Tiger.) Readability uses javascript, which I do have turned on. The problem (of it not working) doesn't seem to have anything to do with the NoScript add-on either, as I tried allowing everything on the page and it still didn't work. Any ideas of what to try next?
''Duplicate post, continue [https://support.mozilla.com/en-US/questions/746624 here]''

Hi there.
By chance, I too have the readability bookmarklet installed (but I don't use it that much, to be honest), and it works ok for me. It's possible that you are having a problem with some Firefox add-on that is hindering your Firefox's normal behavior. Have you tried disabling all add-ons (just to check), to see if Firefox goes back to normal?
Whenever you have a problem with Firefox, whatever it is, you should make sure it's not caused by one (or more than one) of your installed add-ons, be it an extension, a theme or a plugin. To do that easily and cleanly, run Firefox in [http://support.mozilla.com/en-US/kb/Safe+Mode safe mode] (don't forget to select ''Disable all add-ons'' when you start safe mode). If the problem disappears, you know it's from an add-on. Disable them all in normal mode, and enable them one at a time until you find the source of the problem. See [http://support.mozilla.com/en-US/kb/Troubleshooting+extensions+and+themes this article] for information about troubleshooting extensions and themes and [https://support.mozilla.com/en-US/kb/Troubleshooting+plugins this one] for plugins.
If you need support for one of your add-ons, you'll have to contact its author.
If the problem does not disappear when all add-ons are disabled, please tell me, so we can work from there. Please have no fear of following my instructions to the line, as all can be easily undone.

I have tried to reindex my messages but I still can not get the search function to work in email

I have tried reindecing my messages by rebuilding the library but I still can't get my message function to work in mail. Any proposed solutions much appreciated.

Some of your user files (not system files) have incorrect permissions or are locked. This procedure will unlock all your user files, reset their ownership, and remove their access-control lists. If you've set special values for those attributes, they will be reverted. In that case, either stop here, or be prepared to recreate the settings if necessary. Do so only after verifying that those settings didn't cause the problem. If none of this is meaningful to you, you don't need to worry about it.
Back up all data.
Step 1
If you have more than one user, and the one in question is not an administrator, then go to Step 2.
Enter the following command in the Terminal window in the same way as before (triple-click, copy, and paste):
{ sudo chflags -R nouchg,nouappnd ~ $TMPDIR..; sudo chown -R $UID:staff ~ $_; sudo chmod -R u+rwX ~ $_; chmod -R -N ~ $_; } 2>&-
This time you'll be prompted for your login password, which won't be displayed when you type it. You may get a one-time warning to be careful. If you don’t have a login password, you’ll need to set one before you can run the command. If you see a message that your username "is not in the sudoers file," then you're not logged in as an administrator.
The command may take several minutes to run, depending on how many files you have. Wait for a new line ending in a dollar sign ($) to appear, then quit Terminal.
Step 2 (optional)
Take this step only if you have trouble with Step 1, if you prefer not to take it, or if it doesn't solve the problem.
Start up in Recovery mode. When the OS X Utilities screen appears, select
Utilities ▹ Terminal
from the menu bar. A Terminal window will open. In that window, type this:
res
Press the tab key. The partial command you typed will automatically be completed to this:
resetpassword
Press return. A Reset Password window will open. You’re not going to reset a password.
Select your startup volume ("Macintosh HD," unless you gave it a different name) if not already selected.
Select your username from the menu labeled Select the user account if not already selected.
Under Reset Home Directory Permissions and ACLs, click the Reset button.
Select
 ▹ Restart
from the menu bar.

TS3274 I can not get my video button to work

I can not get my video button to work, it will not response when I try to use it

Try sliding the words up or down to select the various modes.

I have a macbook pro version 10.7.5 and my mailbox will not open at all and comes up with a quit message even though it is not open. how can i get into my account. it works on my iPhone an i have internet and all other functions working on my computer

I have a macbook pro version 10.7.5 and my mailbox will not open at all and comes up with a quit message even though it is not open. how can i get into my account. it works on my iPhone and i have internet and all other functions working on my computer

Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Step 1
Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
View ▹ Show Log List
from the menu bar.
Enter the name of the crashed application or process in the Filter text field. Select the messages from the time of the last crash, if any. Copy them to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
When posting a log extract, be selective. In most cases, a few dozen lines are more than enough.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Important: Some private information, such as your name, may appear in the log. Anonymize before posting.
Step 2
In the Console window, look under User Diagnostic Reports (not "Diagnostic and Usage Messages") for crash reports related to the crashed process. The report name starts with the name of the process, and ends with ".crash". Select the most recent report and post the entire contents—the text, not a screenshot. I know the report is long. Please post all of it anyway.
In the interest of privacy, I suggest that, before posting, you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if it’s present (it may not be.)
Please don’t post other kinds of diagnostic report—they're very long and rarely helpful.

How can I get to DFU mode with a broken power button?

How can I get to DFU mode with a broken power button?

aarons84 wrote:
This is bad, but i tried jailbraking my iphone
You may as well stop there. We can't help you.

How can I get my web cam to work in Adobe Connect ?

This is actually an end user's question that I am having trouble answering to...
We use Adobe Connect to give online language classes, the end user is one of the students.
I cannot find the right Support answer to give him.
Problem:
My camera does not work when I connect to Adobe's rooms but camera works fine with other software.
Even though I suspected my old camera was working fine, yesterday I went ahead and bought a new camera.
I thought perhaps my webcam software may have been a problem, so I bought a different type camera with different software.
Even after removing all the old software, same result:
I surmised the problem might be caused by my firewall and security software, so once I tried changing the permissions for Adobe, and my Webcam, but that didn’t work.
Another time, I restarted my computer right before class and then turned off my firewall completely so there would be no interference but to no avail. I’m totally perplexed.
Isn’t there anyone else experiencing a similar problem?   Has anyone else found a solution?
I run Windows Vista with McAfee Internet Security Software. I always reboot the computer before class and open no other programs other than Google Chrome.
I now have a brand new Microsoft LifeCam Cinema Camera with LifeCam 3.5 Webcam Software.
I test my camera before going online. It always works fine.   Then I shut down the camera program and login into class.
When I “connect webcam” in the room, the light on my camera comes on (suggesting that it is ON), but only a black image is transmitted to the room.

Check to see if you have Google Voice installed. If so, remove it and see
if your problem vanishes. If not Google Voice, check to see if you have
any other communications software which interacts with your cam and
disable it. This was the problem I had with a similar problem on a Mac.
MosesJOI <[email protected]>
10/13/11 12:08 PM
Please respond to
[email protected]
To
jsb152 <[email protected]>
cc
Subject
How can I get my web cam to work in Adobe Connect ?
Re: How can I get my web cam to work in Adobe Connect ?
created by MosesJOI in General Discussion - View the full discussion
Thanks a lot Heyward for the swift reply !
I sent the advice out to the end user, but unfortunately this wasn't the
solution.
His reply is below :-
The default resolution of my new camera is already set at 640x360, but I
went ahead and tried several lower resolutions (e.g. 424x240; 320x240; and
160x120) but none worked in the room - camera still showed up as black
blank screen. Also, as far as I can tell, I don’t have the option of
adjusting the frame rate.
I started playing around with my Internet Security Settings to see if they
might be playing a role. So far, all to no avail.
Hmm...quite a tricky one - webcams always are - maybe if he can find a way
to adjust the frame rate (?).
He's going to fiddle about with the settings a bit more and see if
something does the trick.
If anyone has had a similar problem and found an ingenious solution,
please jot on a note on this thread.
Replies to this message go to everyone subscribed to this thread, not
directly to the person who posted the message. To post a reply, either
reply to this email or visit the message page: [
http://forums.adobe.com/message/3969561#3969561]
To unsubscribe from this thread, please visit the message page at [
http://forums.adobe.com/message/3969561#3969561]. In the Actions box on
the right, click the Stop Email Notifications link.
Start a new discussion in General Discussion by email or at Adobe Forums
For more information about maintaining your forum email notifications
please go to http://forums.adobe.com/message/2936746#2936746.

How can I get iCloud to accept my working Apple ID and password

My Apple ID and password works for iTunes and App Store. I'm trying to set up iCloud on my iPhone and iPad but i keep getting an error message that reads unsupported ID. Apple ID must be in the form of email address (@me.com). I don't have a MobileMe account. How can I get iCloud to accept my working Apple ID and password?

I've also reset my password to my Apple ID. I still get the Unsupported ID and password.

Can't get WDS Relay mode to work.

Similar Messages

Maybe you are looking for