Cannot make any changes to SF-302-08MP
This is the third series 300 switch I've configured, but have not run across this issue before. Hoping someone out there can help. I've attached to the switch via the console port and even tried with the web interface but get the same results. Upon booting the switch asks for the default user ID and password, then it prompts to change the password. I do this and then go to configure the device with the new IP address, add a new user ID and password and VLAN. All changes seem to save as I get no errors. However, when the device is rebooted, all changes are lost. I've even went so far as to delete the startup-config file but still no luck. Version information is as follows:
SW Version: 1.0.0.27 (Date: 28-Apr-2010, Time: 13:33:55)
Boot Version: 1.0.0.4 (Date: 08-Apr-2010, Time: 16:37:57)
HW Version: V01
Any ideas would be appreciated.
Cheryl
Cheryl,
First use the console to upgrade firmware to 1.1.1.8 .After the upgrade change the active image to your second image and upgrade again. Once both images are upgraded, log back into switch console or web gui and configured.(You will need TFTP program)
If you're configuring via CLI (copy run start-command) will save your running-config to startup-config.
If able to log into web gui - when making changes save button will glow/light up at the top of browser. Click on save this will take you to location to save running config to startup config.
If you need support please call SBSC @ 1-866-606-1866 and open a support case.
Thanks,
Jasbryan
Similar Messages
-
My Bridge CC opens in a locked mode - I cannot make any changes (dump cache) - it says "other instances of Adobe Application Manager are running, which must be closed." I have to force quit Bridge to get out of it. I tried to uninstall Bridge and re-install it but it did the same thing. Any ideas where to go next?
The fact that I uninstalled Bridge and reloaded it has me concerned as to what to do next.?You need to force quit all other (real or fake) instances of the Application Manager. Instructions differ between Mac or Win.
A lot more information about your hardware and software is needed.
BOILERPLATE TEXT:
If you give complete and detailed information about your setup and the issue at hand,
such as your platform (Mac or Win),
exact versions of your OS, of Photoshop (not just "CC", but something like CC2014.v.2.2) and of Bridge,
your settings in Photoshop > Preference > Performance
the type of file you were working on,
machine specs, such as total installed RAM, scratch file HDs, total available HD space, video card specs, including total VRAM installed,
what troubleshooting steps you have taken so far,
what error message(s) you receive,
if having issues opening raw files also the exact camera make and model that generated them,
if you're having printing issues, indicate the exact make and model of your printer, paper size, image dimensions in pixels (so many pixels wide by so many pixels high). if going through a RIP, specify that too.
a screen shot of your settings or of the image could be very helpful too,
etc.,
someone may be able to help you (not necessarily this poster, who is not a Windows user).
Please read this FAQ for advice on how to ask your questions correctly for quicker and better answers:
http://forums.adobe.com/thread/419981?tstart=0
Thanks! -
In iTunes under my device, under the apps tab, Why are all the options shaded out? I cannot make any changes, select any apps or do anything with the apps. I was able to load a few apps and sync but cannot sync anymore to my phone.
Hi,
( I search for iChat questions when I have finished in the iChat Forum)
So the menu bar reads iChat, File, Edit, View, Buddies, Video, Window and Help
There is no Buddy List open.
There is no other window for iChat open.
In the iChat Menu you only have access to Status.
Is an item ticked in the list ?
Is this a green (Available item) or Red ( an Away one) ?
Can you access the Accounts option ? (Sitll in the iChat Menu)
Is anything in here ticked ?
In the Window menu any Logged in account should appear in the list (Between the Next Chat and File Transfer items)
It would be useful to know which version of iChat this is.
If no account is ticked (iChat Menu > Accounts) or not showing in the Window Menu, plus you cannot determine the Status and you cannot access the Preferences then you need to access your Home Folder/Library/Preferences
As the Library in the Home Holder is Invisible in Lion you will need the Finder's Go Menu > Go to Folder option (you can use it in earlier OS versions if you want)
Type in:-
~/Library/Preferences
Find the file called com.apple.ichat.plist
Drag it to the Trash and Restart iChat.
This will lose all the settings in iChat that you have changed from Defaults but there is no way around this.
9:23 PM Saturday; August 27, 2011
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
G4/1GhzDual MDD (Leopard 10.5.8)
MacBookPro 2Gb( 10.6.8)
Mac OS X (10.6.8),
"Limit the Logs to the Bits above Binary Images." No, Seriously -
Hi, Since updating to 10.7.2 I cannot make any changes to my web site. I just keep getting the same stupid message asking if I have an account even though I am already logged in. Any thoughts. Thanks
Go and log out of your MobileMe account and then try logging back in again with a dummy username and password. This can help clear it and then just log back in again with your normal username and password.
Note though that iWeb does not require a password or username to use it - this is MobileMe.
Also, start thinking about MobileMe alternatives before you are forced to in June. -
When syncing Apps on my iPhone 5 through iTunes, they are all greyed over and I cannot make any changes. How can I fix this. It never happened with my iPhone 4
Connect your device to iTunes and in the the window were all the apps are greyed out make sure the 'Sync Apps' checkbox (top left corner) is selected.
-
The kerning tool appears to be stuck? Cannot make any changes to text boxes in new or existing files
When I try to adjust the kerning in any text box, whether it be in a new or existing file, the change will not take place. It will just automatically return to either the default. Please help!
Thanks, perhaps this might help. as you can see the kerning is set at 300 which should make the T/E very far apart they aren't. The "after" shows the kerning set at (0), even though I made the change to 300. The cursor is in the correct place, even though it doesn't appear on the screenshots.
-
I can´t edit in my Google calendar. I access the site, but cannot make any change.
Recently begun this bug. I can enter the site but I caný do anything more.
Clear the cache and the cookies from sites that cause problems.
"Clear the Cache":
*Tools > Options > Advanced > Network > Cached Web Content: "Clear Now"
"Remove Cookies" from sites causing problems:
*Tools > Options > Privacy > Cookies: "Show Cookies"
Start Firefox in <u>[[Safe Mode|Safe Mode]]</u> to check if one of the extensions (Firefox/Tools > Add-ons > Extensions) or if hardware acceleration is causing the problem (switch to the DEFAULT theme: Firefox/Tools > Add-ons > Appearance).
*Do not click the Reset button on the Safe mode start window or otherwise make changes.
*https://support.mozilla.org/kb/Safe+Mode
*https://support.mozilla.org/kb/Troubleshooting+extensions+and+themes -
I deleted my administrator account and cannot make any changes in preferences.
I deleted my administrator account and log my users & groups is locked. I cannot open it, with name and old password. I cannot restore as Lion was downloaded from app store and needs login to re download.
HelpLaunch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ If you’re running OS X 10.7 or later, open LaunchPad. Click Utilities, then Terminal in the page that opens.
Drag or copy — do not type — the following line into the Terminal window, then press return:
dscl . -read /groups/admin GroupMembership
You should get the following output below what you entered:
GroupMembership: root admin1 admin2 ...
where admin1, admin2, ... are the names of the admin users. -
When I go to options I cannot access "content" so I cannot make any changes to popups
I've been getting a lot of popups and want to check if I have block popups clicked but I cannot access the "content" tab under options. I can click on all the other tabs but the "content" tab just shows the last tab I clicked on...
One reason for lots of pop-ups is a bad add-on. I suggest starting your cleanup here:
(1) Open the Windows '''Control Panel''', Uninstall a Program. After the list loads, click the "Installed on" column heading to group the infections, I mean, additions, by date. This can help in smoking out undisclosed bundle items that snuck in with some software you agreed to install. Take out as much trash as possible here.
(2) Open Firefox's '''Add-ons page''' using either:
* Ctrl+Shift+a
* "3-bar" menu button (or Tools menu) > Add-ons
In the left column, click '''Plugins'''. Set nonessential and unrecognized plugins to "Never Activate".
In the left column, click '''Extensions'''. Then, if in doubt, disable (or Remove, if possible) unrecognized and unwanted extensions.
Often a link will appear above at least one disabled extension to restart Firefox. You can complete your work on the tab and click one of the links as the last step.
Any improvement?
(3) You can search for remaining issues with the '''scanning/cleaning tools''' listed in our support article: [[Troubleshoot Firefox issues caused by malware]]. These on-demand scanners are free and take considerable time to run. If they finish quickly and especially if they require payment, you may have a serious infection. I suggest the specialized forums listed in the article in that case. -
I wish to use Spread Sheets developed on my Imac (OSX 10.6.8 with Numbers 08) on my new Ipad Mini. Currently they will open but I cannot make entries.
Is there some software I need to download to my Ipad ?
If I update my Imac Numbers 08 will it still work with existing spread sheets ?
If I upgrade my OSX 10.6.8 will it impact my files originated under my old OSX and will all my programs work?
Is there a work aropund that will allow me to use those Spread Sheets on my Ipad ?
As informative as Apple is with their products, I see little that addresses compatability issues. Art they non existant ?
I hate to make any changes unless I know I am not going to be causig a lot of grief!
Any assistance would be appreciated.On looking at the secure.log on the iMac with OSX10.6.8, I see these entries at each attempt to scp into the iMac:
Dec 29 11:06:20 molika sshd[7248]: in pam_sm_authenticate(): Failed to determine Kerberos principal name.
Dec 29 11:06:26 molika sshd[7246]: Accepted keyboard-interactive/pam for prowat from 137.110.243.132 port 35571 ssh2
Dec 29 11:06:26 molika com.apple.SecurityServer[26]: Session 0x236a14 created
Dec 29 11:06:26 molika com.apple.SecurityServer[26]: Session 0x236a14 attributes 0x20
Dec 29 11:06:27 molika com.apple.SecurityServer[26]: Session 0x236a14 dead
Dec 29 11:06:27 molika com.apple.SecurityServer[26]: Killing auth hosts
Dec 29 11:06:27 molika com.apple.SecurityServer[26]: Session 0x236a14 destroyed
I don't know what to make of this.
Peter R -
Record about my phone (bought in Verizon store and connected to Verizon for 4 years) has been corrupted and now I can not make any changes to my data plan. Several sessions with the technical support and management have not resolved this issue. Each time technical people and top managers promised that this issue will be resolve tomorrow and they will cal me. Nothing happend!! I can not even cancel my service not just to upgrade it. Completely locked.
Any advice?
Thanks.
Alex.Cannot figure out what your talking about since it makes no sense.
If you are the account owner you can go to the My Verizon web portal http://www.verizonwireless.com
You must log in with your cell number and your my Verizon portal password. Not the account pin.
Once there you can change your plan and services. However repeated incorrect login attempts will lock you out of the site. It a fraud prevention measure.
1-800-922-0204 call support with your cell number and or account number and account pin and they can assist you.
If you don't have the information then there is nothing they can do.
If you can verify who you are they may be able to reset your account access. But only if you are the account owner.
Good Luck -
i forgot my icloud password and my email address for icould is no longer effective. i cant make any change to my iphone now, what should i do?
Contact Apple for assistance by going to https://expresslane.apple.com, then click More Products and Services>Apple ID>Other Apple ID Topics>Lost or forgotten Apple ID password.
-
I recently switched from my iphone to a samsung Galaxy S4, trading in my iphone. I now can not send/receive text messages from any iphones to my galaxy S4. Since I traded the iphone in, I can't access it to make any changes. Any ideas?
http://support.apple.com/kb/TS5185
-
Hello, I have Windows 7, and I have now to install Windows 8 on my Computer, and since, I cannot make any more of update of Apple of itune in Windows 8. Nor to download the software recent of itune... That have to I make???
Hello,
The Reset Firefox feature can fix many issues by restoring Firefox to its factory default state while saving your essential information. <br>
'''Note''': ''This will cause you to lose any Extensions and some Preferences.''
*Open websites will not be saved in Firefox versions lower than 25.
To Reset Firefox do the following:
#Go to Firefox > Help > Troubleshooting Information.
#Click the "Reset Firefox" button.
#Firefox will close and reset. After Firefox is done, it will show a window with the information that is imported. Click Finish.
#Firefox will open with all factory defaults applied.
Further information can be found in the [[Reset Firefox – easily fix most problems]] article.
Did this fix your problems? Please report back to us!
Thank you. -
Hello All,
I am getting this error while I am connecting my access database website for the change
"This database was connected to a Microsoft Access Services site that is not compatible with this version of Microsof Access. You cannot make design changes or modify data in database."
I am using SharePoint 2010 and Microsoft Office 2010.
I have created one Contact Database Site and now I am trying to modify the layout of the form in Access. and I am getting the error that I have mentioned.
Please provide help on it.
Thanks in Advance....Hello All,
I got the answer, we have to enable the port 80 or where the access service is deployed and we have to change Trust setting and also, enable the macro from Access.
Hope this will help to other....
Maybe you are looking for
-
My ipod has not been able to back up for a while now. When I plug it in it syncs then it gives me a back up error message -20. If anyone knows how to fix this problem i would appreciate it.
-
This evening, as I updated my iPod, I got the following message: "Songs on the iPod cannot be updated because all of the playlists selected for updating no long exist." This seems not to be true, as I have my iTunes completely intact. Nothing has cha
-
Hi, I have a queer problem with batch inserts in oracle, loaded on a sun solaris m/c. I'm trying to do a batch insert using the executeBatch() api of java. I am able to do batch insertions from my workstation i.e win2k properly . But i'm unable to do
-
Here i want to retrive columns names in table inside my database . I used Access , but i have error : Server= null !!! why this ?!! import java.sql.Connection; import java.sql.DriverManager; import java.sql.ResultSet; import java.sql.ResultSetMetaDat
-
Reader install failing but installer says it completed successfully
I am trying install Acrobat Reader 9 on a Windows XP Pro machine. The download manager starts, says it is downloading and installing installing the reader, it completes the download, then it says installation was successful, and the download and inst