Change data vlan

How to change data vlan for PC connected behind ip phone. I've tried with switchport trunk native vlan XXX but it didn't work, here is present config
interface FastEthernet0/12
switchport mode dynamic desirable
switchport voice vlan 10
mls qos trust device cisco-phone
mls qos trust cos
auto qos voip cisco-phone
wrr-queue bandwidth 20 1 80 1
wrr-queue min-reserve 1 5
wrr-queue min-reserve 2 6
wrr-queue min-reserve 3 7
wrr-queue min-reserve 4 8
wrr-queue cos-map 1 0 1 2 4
wrr-queue cos-map 3 3 6 7
wrr-queue cos-map 4 5
priority-queue out
spanning-tree portfast
end

All you need is "switchport accss vlan

Similar Messages

Passing voice and data Vlans on Cisco SG200-08P help

Hello All,
I'm struggling with a configuration issue on the Cisco SG200-08P.
We are using the Cisco SG200-08P on a mobile cart that will go from class room to class room that will have computer and cisco Voip phone plugged into it. The issue is that each of our closets are in differnt VLANS ( 1 voice and 1 data....lets say data vlan 20 and voice vlan 2025 for conversation) and that we route to each closet.
It would be great if I could just create a generic data and voice vlan to dynamically pick up what the upstream switch has however, it seems that I've been unsuccessful in doing so.
So far I can pass the data Vlan no probablem. The upstream switch port is set to access port and a switch port access voice vlan (these are 3750x switches)
If the above is not possible I guess I will take what I can get. Should I just create data vlan 20 and voice vlan2025 on the Cisco SG200-08P and make a trunk port on the Cisco SG200-08P and a trunk on the 3750x? Is there an option on the Cisco SG200-08P to tag voice traffic?
I'm also concerned with VTP and I did not see an area in the Cisco SG200-08P to set that as a client and transparent mode.
Thanks for any help,
Dan

On a Catalyst switch, when a port is defined as a trunk without a vlan specified on the port, all vlan pass through the port. On a small business switch it is nearly the opposite. You must specify the vlans on the links. Additionally, ingress filter discards anything not associated to the port.
802.1q specifies there must be an untagged vlan which is the native vlan (of course you can make exceptions, tagging the default vlan..).
One thing I did in the past with a 2960, I made an LLDP network policy and it basically "provisioned" the downstream switch connecting link and voice vlan. That may be another idea for you.
Here's a link that may be useful-
https://supportforums.cisco.com/message/3811376
Here is the 2960 config I used to feed a SB switch voice info
Switch#show run
Building configuration...
Current configuration : 2206 bytes
! Last configuration change at 00:41:16 UTC Mon Mar 1 1993
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Switch
boot-start-marker
boot-end-marker
no aaa new-model
system mtu routing 1500
vtp mode transparent
network-policy profile 1
voice vlan 100 cos 4
spanning-tree mode pvst
spanning-tree extend system-id
vlan internal allocation policy ascending
vlan 2
name test
vlan 100
lldp run
interface FastEthernet0/1
network-policy 1
spanning-tree portfast
interface FastEthernet0/2
interface FastEthernet0/3
interface FastEthernet0/4
interface FastEthernet0/5
interface FastEthernet0/6
interface FastEthernet0/7
interface FastEthernet0/8
interface FastEthernet0/9
interface FastEthernet0/10
interface FastEthernet0/11
interface FastEthernet0/12
interface FastEthernet0/13
interface FastEthernet0/14
interface FastEthernet0/15
interface FastEthernet0/16
interface FastEthernet0/17
interface FastEthernet0/18
interface FastEthernet0/19
interface FastEthernet0/20
interface FastEthernet0/21
interface FastEthernet0/22
interface FastEthernet0/23
interface FastEthernet0/24
interface FastEthernet0/25
interface FastEthernet0/26
interface FastEthernet0/27
interface FastEthernet0/28
interface FastEthernet0/29
interface FastEthernet0/30
interface FastEthernet0/31
interface FastEthernet0/32
interface FastEthernet0/33
interface FastEthernet0/34
interface FastEthernet0/35
interface FastEthernet0/36
interface FastEthernet0/37
interface FastEthernet0/38
interface FastEthernet0/39
interface FastEthernet0/40
interface FastEthernet0/41
interface FastEthernet0/42
interface FastEthernet0/43
interface FastEthernet0/44
interface FastEthernet0/45
interface FastEthernet0/46
interface FastEthernet0/47
interface FastEthernet0/48
interface GigabitEthernet0/1
switchport mode trunk
interface GigabitEthernet0/2
interface Vlan1
no ip address
interface Vlan100
no ip address
ip http server
ip http secure-server
logging esm config
line con 0
line vty 5 15
end
Switch#
-Tom
Please mark answered for helpful posts

Voice & Data VLAN Implementation

Hello,
We have recently purchased an asterisk based IP PBX, it is hosted in-house which uses Grandstream IP GXP1405 Phones. We have configured and installed. we are able to receive calls and dial out. Unfortunately our infrastructure was not up to par with the PBX. We purchased an SG300 20 port switch, with two RV320 VPN Dual Wan Routers. We have a total of 4 offices. this is the current setup:
HQ 1 - Asterisk Based IP PBX, RV320 VPN router, & SG300
HQ2 - RV320 VPN Router
Office 1 - Simple Linksys Router
Office 2 - Simple Linksys Router
We have established connectivity using the Tunnels incorporated onto the RV320 Routers, so we are able to connect to the HQ locations.
However since the RV320 has dual WAN setup's, we have now have 2 Internet Connections independent from each other. Our goal is to perform the following:
WAN 1 = to be used for Data Traffic
WAN 2 = to be used for Voice Traffic
We would like to do this by separating the VLAN's and directing the traffic from one VLAN to a specific WAN using the equipment above.
We are having issues establishing the voice VLAN and redirecting the traffic once created.
Any help would be appreciated it.
Thanks,

Hi Soiser,
My name is Mehdi from Cisco Technical Support,
For the Voice & Data VLAN Implementation we can manage to do it with different way :
First example hard coding the voice vlan
1. we can have the switch Layer 2
2. Configure on the switch Vlan Data and Vlan voice (in this example will have Vlan 1 Data and 100 is Voice vlan) --> under Vlan management --> Create Vlan
3. Configure the port from where the switch is connected to the Router and change it to Trunk port and add vlan voice (until here we made the data traffic as untagged traffic and voice traffic as tagged) by going under Vlan managemnent --> Port Vlan Membership --> select port 20 --> click on join vlan --> by default you have 1UP in the right so now select vlan 100 and select Tagged and move it to the right
4. And the same trunk port with both vlan for all the port on the switch where you have voice and data
5. here we done with the switch
Second Using Auto-voice Vlan implementation
1. We Can have the switch also layer 2
2. we need to configure the AUTO-Voice Vlan under vlan management--Voice Vlan --> Properties by changing the voice vlan 100 and we have two option to choose
Dynamic Voice VLAN: Enable Auto Voice VLAN OR Enable Telephony OUI : the difference is when you have Cisco Phone enable auto-voice vlan and the phone will take all the informations like (Vlan ,..) via CDP protocol
if you have 3rd part Phone select Enable Telephony OUI and configure the first 3 bits of the MAC address of the phones by going under voice vlan -->Telephony OUI --> add 3 bits of the MAC address of the phone but not for all the phones is by model remember first 3 bits of mac
address is the model of the device!
Auto Voice VLAN Activation: select "Immediate"
3. and enable telephony OUI interface
-------> We didn't configure voice vlan the switch will assign voice vlan to the phones when they connect to the switch by CDP or Telephony OUI
Now going to the router :
- By default RV320 Has Vlan ID 100 with subnet 192.168.3.1 so we can change only the ip address of vlan interface or if you deleted by some reason we will need to create a voice vlan by going to Setup-->Network--> multiple Subnet Table --> Create the Vlan interface in my example i will put 10.10.10.1 and mask 255.255.255.0
- Just to check if you going to port management --> Vlan Membership you will see vlan 1 is untagged and vlan voice is tagged this also in our switch !! you can connect the switch from any port of the router since all of them are the same
- if you wantr to change and coding only port 4 for example as trunk and remove other port the voice vlan you can
---> Now should work the voice vlan and data vlan
But we have two WAN and you want to bind the WAN 1 to Data and Wan 2 to Voice
we need to configure Protocol Binding
under System management --> Dual WAN --> Protocol Binding
there we can choose all traffic , source IP (voice network 10.10.10.1 - 10.10.10.254) , destination 1.0.0.1 to 223.255.255.254, and select WAN 2
and another rule but the source will be the data network and select WAN 1
This is it just example and how the Voice vlan work and how to use Protocol binding if you have two WAN
Please if you have the switch on L3 by some reason and you have SVI configured in the switch , please call the Cisco Technical Support Center we will be happy to help you to accomplish your need with layer 3 switch is almost the same few change and we need more information's from your topology that's why by phone is better !! :)
Please rate the post or mark as answered to help other Cisco Customers
Have a nice day
Regards
Mehdi

Change default VLAN on a catalyst express 500 series.

Hi. On one of our networks we have a CE 500 series 24 port switch (the one with just 4POE ports). As it hasnt got a proper console interface, is there a way of changing the default data vlan from 1 to 2 without having ro reset it?
I've logged into the web page on it but I cant change my default data vlan ID because its greyed out.. Does the default data VLAN ID need to be specified on installation?
Thanks

You may porbably get help from the below link:
http://www.cisco.com/en/US/products/ps6545/products_configuration_example09186a00806da6c9.shtml#vlans

How to get changed data in ALV in Web Dynpro for ABAP

METHOD on_data_check .
DATA:
    node_spfli                          TYPE REF TO if_wd_context_node,
    node_sflight                        TYPE REF TO if_wd_context_node,
    itab_sflight2                        TYPE if_display_view=>elements_sflight.
node_spfli = wd_context->get_child_node( name = if_display_view=>wdctx_spfli ).
node_sflight = node_spfli->get_child_node( name = if_display_view=>wdctx_sflight ).
CALL METHOD node_sflight->get_static_attributes_table
    IMPORTING
      table = itab_sflight2.
this code is ..get all data(changed and not changed)
but i want get changed data only, not all data.
how to get changed data?
Edited by: Ki-Joon Seo on Dec 27, 2007 6:04 AM

Hi,
To get only the changed data in the ALV grid of a WD, you need to capture the "ON_DATA_CHECK" of the ALV grid.
To this please do the following in the ALV initialization of the ALV table settings :
    lr_table_settings->set_data_check(
            IF_SALV_WD_C_TABLE_SETTINGS=>DATA_CHECK_ON_CELL_EVENT ).
You may also do this:
    lr_table_settings->set_data_check(            IF_SALV_WD_C_TABLE_SETTINGS=>DATA_CHECK_ON_CHECK_EVENT)
The above two ways would depend on when do you need to check for the changed data. If you want to check the data as soon as it is entered, then use the first method. Else, use the second method.
You need to register an EVENT HANDLER for this event.(You may do this in your VIEW or Component Controller).
In this Event handler, you would find an importing parameter R_PARAM which is a ref type of      IF_SALV_WD_TABLE_DATA_CHECK.
The attribute T_MODIFIED_CELLS of this interface IF_SALV_WD_TABLE_DATA_CHECK will contain the modified cells of the ALV with the old & new values.

Can not change data in Input Ready Query

All,
I have created an input ready query on an aggreagation level which has one transactional cube underlying it however, after run the query I am unable to change data in the cells even though I get a warning message saying query is ready for input
Note:
1. The underlying realtime cube is in "Planning Mode:Loading not allowed" state in rsa1
2. I tried including all characteristics so that the record can be uniquely identified at that aggregation level).
3. I am not using any characteristic restrictions
4. I have not set any data slices
5. I have set the property for Planning "Start query in Change Mode"
6. I have set the 'Key Figure' Planning Properties to "Can be changed Manually or via Planning Functions" for the key figures
7. I do not have currency/unit in row/column.
8. There are any locks occurring
Any pointers welcome.
Thanks,
Milind

Hi Milind,
Was wondering how was your problem solved. I get the same message when I run the query in web from query designer and in bex analyzer the cells are not updated with the changes that I make.
I am hitting my head against the wall to figure what could be the problem as my plan query is simply based on aggregation level created directlty upon the real time info cube.
Have cross checked all the points that you mentioned in this post but I cells do not change.
There should be some way around to solve this problem.
Thanks

Can we change data in string object.

Can we change data in string object.

Saw this hack to access the char[]'s in a String in another thread. Beware that the effects of doing this is possible errors, like incorrect hashCode etc.
import java.lang.reflect.*;
public class SharedString {
        public static Constructor stringWrap = null;
        public static String wrap(char[] value, int offset, int length) {
                try {
                        if (stringWrap == null) {
                                stringWrap = String.class.getDeclaredConstructor(new Class[] { Integer.TYPE, Integer.TYPE, char[].class });
                                stringWrap.setAccessible(true);
                        return (String)stringWrap.newInstance(new Object[] { new Integer(offset), new Integer(length), value });
                catch (java.lang.NoSuchMethodException e) {
                        System.err.println ("NoMethod exception caught: " + e);
                catch (java.lang.IllegalAccessException e) {
                        System.err.println ("Access exception caught: " + e);
                catch (java.lang.InstantiationException e) {
                        System.err.println ("Instantiation exception caught: " + e);
                catch (java.lang.reflect.InvocationTargetException e) {
                        System.err.println ("Invocation exception caught: " + e);
                return null;
        public static void main(String[] args) {
                char[] chars = new char[] { 'l', 'e', 'v', 'i', '_', 'h' };
                String test = SharedString.wrap(chars, 0, chars.length);
                System.out.println("String test = " + test);
                chars[0] = 'k';
                chars[1] = 'a';
                chars[2] = 'l';
                chars[3] = 'l';
                chars[4] = 'a';
                chars[5] = 'n';
                System.out.println("String test = " + test);
} Gil

Can't view changed data in journal data

Hi,
I have implemented JKM Oracle 10g Consistent Logminer on Oracle 10g with the following option.
- Asynchronous_mode : yes
- Auto_configuration : yes
1. Change Data Capture -> Add to CDC, 2.Subscriber->subscribe (sunopsis),
3. Start Journal
The journal has been started correctly wothout errors. The journalized table has always the symbol "green clock". All is gook working.
And then i inserted 1 record in source table, but i can't view changed data in journal data. I can't understand why journal data was generated.
There are no errors.
Help me !!!

Did your designer was on the good context ?
Look the list box at the top right of the Designer interface.
You must have the same as the one where you define your journalization.

I can not map field after changing data source location

Hi
I have a small problem that I got a report file and database from my customer, after that I setup database, open the file and change data source to my setting. but some filed can not map. The field mapping widonw does not display all field in the table. Of course I have checked the missing fields are existing in the table.
OS:Windows7
DB:Oracle11
CR:XI Release 2
Does anyone have an idea?

hi,
In Map Fields window, there is an option "Match Type".
Please Unchek that option, so that you will be able to see all the fields from that table.
Also, while mapping please verify the datatypes of source and target fields.
Regards,
Vamsee

Can you help me about change data captures in 10.2.0.3

Hi,
I made research about Change Data Capture and I try to implement it between two databases for two small tables in 10g release 2.MY CDC implementation uses archive logs to replicate data.
Change Data Capture Mode Asynchronous autolog archive mode..It works correctly( except for ddl).Now I have some questions about CDC implementation for large tables.
I have one senario to implement but I do not find exactly how can I do it correctly.
I have one table (name test) that consists of 100 000 000 rows , everyday 1 000 000 transections occurs on this table and I archive the old
data more than one year manually.This table is in the source db.I want to replicate this table by using Change Data Capture to other stage database.
There are some questions about my senario in the following.
1.How can I make the first load operations? (test table has 100 000 000 rows in the source db)
2.In CDC, it uses change table (name test_ch) it consists of extra rows related to opearations for stage table.But, I need the orjinal table (name test) for applicaton works in stage database.How can I move the data from change table (test_ch) to orjinal table (name test) in stage database? (I don't prefer to use view for test table)
3.How can I remove some data from change table(name test_ch) in stage db?It cause problem or not?
4.There is a way to replicate ddl operations between two database?
5. How can I find the last applied log on stage db in CDC?How can I find archive gap between source db and stage db?
6.How can I make the maintanence of change tables in stage db?

Asynchronous CDC uses Streams to generate the change records. Basically, it is a pre-packaged DML Handler that converts the changes into inserts into the change table. You indicated that you want the changes to be written to the original table, which is the default behavior of Streams replication. That is why I recommended that you use Streams directly.

Yes, it is possible to capture changes from a production redo/archive log at another database. This capability is called "downstream" capture in the Streams manuals. You can configure this capability using the MAINTAIN_* procedures in DBMS_STREAMS_ADM package (where * is one of TABLES, SCHEMAS, or GLOBAL depending on the granularity of change capture).

A couple of tips for using these procedures for downstream capture:
 1) Don't forget to set up log shipping to the downstream capture database. Log shipping is setup exactly the same way for Streams as for Data Guard. Instructions can be found in the Streams Replication Administrator's Guide. This configuration has probably already been done as part of your initial CDC setup.
 2) Run the command at the database that will perform the downstream capture. This database can also be the destination (or target) database where the changes are to be applied.
 3) Explicitly define the parameters capture_queue_name and apply_queue_name to be the same queue name. Example:
 capture_queue_name=>'STRMADMIN.STREAMS_QUEUE'
 apply_queue_name=>'STRMADMIN.STREAMS_QUEUE'

Unable to change Date Created in Metadata

Please help with my first post...
Unable to change Date Created field in Metadata.
I am a newspaper photographer sending .jpg pics with captions to my office from my iMac. They are viewed at the office on Windows PCs using SCC MediaGrid.
When changing Date Created in Metadata Invalid Format warning appears "Format should be ISO 8601 XML compliant, that is YYYY-MM-DDThh:mm[:ss][tz] (eg 2006-07-11T13:14:30-07:00)"
If 2009-09-26, for example, is entered then exported pictures opened up in Photoshop or shown on SCC MediaGrid do not display the date.
To get dates to show up I first have to open a pic in Photoshop, go to File Info, enter 26/9/09 in Date Created and Save As.
Next I have to Import this into Aperture where the Date Created shows as "20090926".
Using Lift Metadata and Stamp Metadata the date can be transferred to other pics.
Now when I export these pics the date does show up in Photoshop and SCC MediaGrid.
Can Date Created be typed straight into field in Aperture?...Very important when pics go into archive on a server.
Also if I hit Return key in a Metadata Caption, to type on the next line, both lines will appear as one with a small square in-between them when viewed on SCC MediaGrid on a Windows PC.
Thanks in anticipation.

Nick I don't generallt use the IPTC metadata, so I'm not sure I will be too much help.
What version of Aperture are you using? I tried both things and I didn't have any problems with the latest version of Aperture on my Mac.
I was able to enter a date into "Date Created" both with and without the time-zone adjustment. Can you tell us the exact string you tried to enter into the "Date Created" and exactly when you get the error? I tried to enter my time zone (eastern US) as "-5:00", but Aperture wouldn't let me enter the 5 and popped up the error message when I typed that key. I had to use "-05:00".
As for the caption, when I hit return, Aperture ends my edit. I cannot reproduce your described behavior of actually getting a new-line into the field. I suspect your problem (although I don't know how you get to your problem) is one of the following:
1) The IPTC standard doesn't tell if the software should use a Unix-style end-of-line (which is a line-feed), or a DOS/Windows style end-of-line (which is carriage-return followed by line-feed). Aperture may put in the Unix-style and your Windows programs don't know what to do with it.
2) The IPTC standard does indicate the end-of-line style, but either Aperture or your other programs don't follow it.
or
3) IPTC Metadata doesn't actually support end-of-line, so Aperture should not allow you to enter multiple lines, but it has a bug so it does allow you to do that.
Can you tell us where exactly you are editing the caption? I tried it in the inspector pane (on the left) in the "Metadata" tab, and then I hit the "IPTC" button at the bottom of the tab.
nathan

Updated my iphone4 with ios6.1 software. App store is not working. Tried rebooting, restoring, changing date, signing with another apple id etc. but no luck. can someone please help?

Updated my iphone4 with ios6.1 software. App store is not working. Tried rebooting, restoring, changing date, signing with another apple id etc. but no luck. can someone please help?

I guess I will wrap this up. I have abandoned iPhoto and viewing my Photo Streams using it and moved to Adobe products (Bridge + PS). So that's that.

Identifying Changed Dates on Documents in SAP B1

Greetingsu2026I have an unusual request that is somewhat long, very serious, and hope folks can help.
A headquarters customer believes a subsidiary company has u2018made upu2019 dates on invoices for previous billings. They describe the date changes as u2018radicalu2019 but I have not personally seen these invoices as of yet and am waiting a FAX. They requested I go into SAP B1 to see if someone has fabricated or made up or changed invoice dates and who it was. They have some specific large-dollar invoices identified to research. The person under suspect (who is no longer there) was considered an expert in SAP B1, so maybe she knew all of the different ways to change dates around. Being an expert means also she might have used some unusual ways to change dates to the ones she wanted.
Here are some of my ideas to discover this situation, but I hope someone can suggest even more steps because I would like to know every way that this situation can be discovered.
1. Open the AR Invoices and use Data > Change Log and concentrate on dates.
2. Run some SQL to validate document dates and system dates. SELECT T0.DocNum, T0.DocDate, T0.CreateDate, T0.TaxDate, T0.UpdateDate FROM OINV T0 WHERE (T0.DocDate does not equal T0.CreateDate OR T0.TaxDate does not equal T0.CreateDate). The results would show invoices that maybe had their dates changed.
3.Run a Document Journal in the Financial Module. Finance > Financial Reports > Accounting > Document Journal with the u2018Expanded Selectionu2019 of AR Invoices and a date range covering the invoices in question. Then see if the Transaction Numbers are out of sequence.
4. Run a Transaction Journal Report Financials > Financial Reports > Accounting > Transaction Journal Report with AR Invoices. Compare this report to Document Journal.
5. Run the Utilities functions of Utilities > Check Document Numbering to see if there any anomalies there in the document numbers.
6. Run the Administration > System Initialization > Document Numbering function to see if a special series has been set up.
7. Check out the AR Invoice numbering order by running another simple SQL covering a range of the invoices in question. SELECT T0.DocNum, T0.TaxDate, T0.CreateDate, T0.UpdateDate FROM OINV T0 WHERE T0.DocNum > 1583 AND T0.DocNum < 3251 ORDER BY T0.CreateDate. Then see if the AR Invoice Numbering Sequence is not consistent.
8. Check out those documents that are connected to each suspect AR Invoice and their associated dates by using the Target and Base Document icons. For example, if a Deliver Document has dates of January 2007 but the AR Invoice date is September 2006, then someone has played around with dates on at least one of the documents.
9. Get copies of the complete company database before the alleged changes were made and a company database as of today and compare the two contents. Only good if the backups are maintained for a long time.
Here come the questions on the ways I BELIEVE dates can be changed but not sure how to find and need to work on them:
QUESTION 1 u2013 If a person DTWs invoices up into SAP B1, how can I tell that DTW was used to change the dates, the date of the DTW run, and the dates that were changed?
QUESTION 2 u2013 If a person uses SQL to update dates on SAP B1, how can I find out that SQL has been used, the date of the SQL run, and the dates that were changed?
QUESTION 3 u2013 If a person goes out and changes the workstation and/or server Date and Timestamp Properties, how can I find that they did that and the date changes? You can do this on your PC by just changing the month, date, and year in Microsoftu2019s Date and Timestamp Properties.
QUESTION 4 u2013 I know SAP has a policy that no SQL can be used to update databases and/or tables and have been told some customers lost support because they did this. What does SAP do to discover this in their lab?
QUESTION 5 u2013 Are there any notes in the portals to help me find changed dates?
QUESTION 6 u2013 Are there any logs SAP B1 produces that can help identify such changes and how do I find and use them?
QUESTION 7 (and this is big) u2013 Are the other ways dates can be changed on AR Invoices and how would I uncover the way it was done and the needed information of Original Date and Changed Date?
Many, many thanks for any help provided since this is a serious situation. If you can make any suggestions it would be greatly appreciatedu2026
Zal
Edited by: Zal Parchem on Mar 13, 2009 7:31 AM

Hi Zal
If this person was an "Expert" on SAP Business One then the only way they would have changed dates would probably be directly in SQL itself. The best way to determine this would be to hope that they slipped up somewhere and forgot to change a particular date in let's say one specific table.
For invoices, start with the post date, doc date & create date. Then check each of these to the OJDT/JDT1 tables for any discrepancies. Next check the ADOC/ADO1 table for multiple instances on the invoice. If only 1 instance then check the create date, time & user as well as the aforementioned dates between OINV/INV1 & ADOC/ADO1. If multiple instances, check the dates from 1 instance to the next (This will indicate dates being changed in the system).
Next check the same dates against OINM table. If any of the dates do not tally then the SQL was changed directly.
Hope this helps. Let me know if you need further assistance.
Kind regards
Peter Juby

How to update changed data in alv grid.

hi experts,
i have a editable alv report how to update the changed data on the grid to database table when i click save.
can anybody tell me how to do this if possible with example.
thanks in advance.
regards,
venu

The code below isn't a working program, but has most of what you should need. Field-symbol <dyn_table> will always have what is in the grid.
FIELD-SYMBOLS: <dyn_table> TYPE STANDARD TABLE,
 <dyn_wa>.
DATA: pt_fieldcat TYPE lvc_t_fcat,
 ls_fcat TYPE lvc_s_fcat,
 new_table TYPE REF TO data,
 new_line TYPE REF TO data.
CREATE OBJECT g_custom_container
 EXPORTING container_name = g_container.
CREATE OBJECT g_grid EXPORTING i_parent = g_custom_container.
CLEAR ls_fcat.
ls_fcat-fieldname = 'MATERIAL'.
ls_fcat-datatype = 'CHAR'.
ls_fcat-intlen = 18.
ls_fcat-outputlen = 18.
ls_fcat-coltext = 'Material'.
ls_fcat-edit = 1.
APPEND ls_fcat TO pt_fieldcat.
CLEAR ls_fcat.
ls_fcat-fieldname = 'QUANTITY'.
ls_fcat-datatype = 'INT4'.
ls_fcat-intlen = 6.
ls_fcat-outputlen = 6.
ls_fcat-coltext = 'Qty'.
ls_fcat-edit = 1.
APPEND ls_fcat TO pt_fieldcat.
CALL METHOD cl_alv_table_create=>create_dynamic_table
 EXPORTING
 it_fieldcatalog = pt_fieldcat
 IMPORTING
 ep_table = new_table.
* assign ref variable to a field symbol
ASSIGN new_table->* TO <dyn_table>.
* Create dynamic work area and assign to FS
CREATE DATA new_line LIKE LINE OF <dyn_table>.
ASSIGN new_line->* TO <dyn_wa>.
* data_itab is filled with data that you want in grid
LOOP AT data_itab INTO data_wa.
CLEAR <dyn_wa>.
ASSIGN COMPONENT 'MATERIAL' OF STRUCTURE <dyn_wa> TO <fs>.
<fs> = data_wa-material.
ASSIGN COMPONENT 'QUANTITY' OF STRUCTURE <dyn_wa> TO <fs>.
<fs> = data_wa-quantity.
APPEND <dyn_wa> TO <dyn_table>.
ENDLOOP.
CALL METHOD g_grid->set_table_for_first_display
 EXPORTING
 i_structure_name = '<DYN_TABLE>'
 is_variant = gs_variant
 i_save = 'A'
 i_default = 'X'
 is_layout = gs_layout
 it_toolbar_excluding = gt_exclude
 CHANGING
 it_outtab = <dyn_table>
 it_fieldcatalog = pt_fieldcat[]
 it_sort = gt_sort[].

Approaches to transfer changed data from a table to another table

Hello expert,
will you please show me all approaches to automatically detect and transfer changed data from a table to another table ? I don't need detail information, but a little comment for those approaches are more welcome.
Many Thanks,
Edited by: 843178 on 19-Dec-2011 2:04 PM

You will want to review information on replication and similar methods
In a nutshell:
Replication allowed data to exist at more than one site and take the Master / original table data and clone it at a different site
As tranporting all of the table data to a remote / clone site got more and more expensive we developed a method
to identify just the 'diffs' and only send those from the master to the clone which needed only the diffs to become a clone of the master table
This has many methods and options, but looking under key words such as
- distributed transations
- materialized views
- replication
... are a few categories that will get you started

Change data vlan

Similar Messages

Maybe you are looking for