Change tabs position from right side to left side

Any one has any idea if the above is possible ?
thanks
Orna

Sure, this is probably specified within the page template or in the corresponding css file.
Denes Kubicek
http://deneskubicek.blogspot.com/
http://www.opal-consulting.de/training
http://apex.oracle.com/pls/otn/f?p=31517:1
http://www.amazon.de/Oracle-APEX-XE-Praxis/dp/3826655494
-------------------------------------------------------------------

Similar Messages

How to set Decimal Point position from right to left Serial Read Evaluate Number within Range over RS-232

I am new to Labview, I am communicating with a TQ8800 Torque meter via RS-232. The 16 digit data stream is as follows:
D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
Each digit indicate the following status :
D0 End Word
D1 & D8 Display reading, D1 = LSD, D8 = MSD
For example :
If the display reading
is 1234, then D8 to D1 is :00001234
D9 Decimal Point(DP), position from right to the left
0 = No DP, 1= 1 DP, 2 = 2 DP, 3 = 3 DP
D10 Polarity
0 = Positive 1 = Negative
D11 & D12 Annunciator for Display
Kg cm = 81 LB inch = 82 N cm = 83
D13 1
D14 4
D15 Start Word
I am using a modified version of the basic_serial_write_read.vi. I am attempting to parse the 16 digit data stream extracting out the number and whether it is positive or negative. I am having trouble with the decimal point placement. Is there an example that could help me with this? After the number is parsed I am then comparing it to see if it is within +/- 9.2 N cm. If it is then the test passes. I am outputing the data to a file. I have included the vi. Also how can I check for different units of the annunciator. Any help would be appreciated. Thank you.
Attachments:
basic_serial_read.vi ‏100 KB

What is the definition of the End Word? You will likely need to figure this out experimentally (the manual doesn't seem to define it). Whatever it is, you should set that as the termination character and enable the termination character. That will help you in keeping your messages in sync. Just tell the VISA Reads to read more than a message should be, something like 30 should work nicely.
The error you are seeing is a buffer overload. This means that the instrument is sending data to you faster than you can process it. So you need to figure out how to perform the read faster. File IO is slow. So you should put that into a seperate loop so that your loop does nothing but read the data from the port as quickly as the data comes in. Use a queue to send the data from the reading loop to the logging loop. This is known as a Producer/Consumer.
And here is a cleaned up version of your code. No need for your express VI or the formula node. Some other general cleaning up also done to make it easier to read.
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines
Attachments:
serial read.png ‏80 KB

Unable to change Axis y location from right side to left

Hi All,
I am working with OBIEE 11.1.1.1.7.
I am tring to change the location of AXIS Y (in chart) from right side to left.
please help :-)

Hi Tyson,
I did exactly what you have mentioned and it worked fine.
But when I am putting the same thing in my custom.css file as mentioned below, IT's NOT WORKING.
uploaded custom.css at
Application XXX>Shared Components>Cascading Style Sheets
custom.css
.TabHolder,.TabHolderC {text-align:left;}calling custom.css in the Page Template (one level tab)
<head>
<title>#TITLE#</title>
<link rel="stylesheet" href="#IMAGE_PREFIX#themes/theme_16/theme_3_1.css" type="text/css" />


<link rel="stylesheet" href="#WORKSPACE_IMAGES#custom.css" type="text/css"/>
#HEAD#
</head>Any idea why it is not picking up???...
Thanks,
Deepak

Hi from few days onwards i found one abnormality in my iphone4s .That is if i observe my phone settings screen from right side of the device top navigation appearing rightside height is more than the left side. In reverse manner from the left side.

Hi from few days onwards i found one abnormality in my iphone4s .That is if i observe my phone settings screen from right side of the device top navigation bar appearing rightside height is more than the left side. In reverse manner from the left side. I dnt know whether it is default feature of iphone or not but i am really disappointed due to this. So please anyone help me in this issue and let me clear my doubt and make me happy. Thanks in advance.

I believe what you are seeing is an optical illusion when viewing the screen from the side. Try to align one of the one of the options in Settings, like General, with the navigation bar you'll see it does the same thing.
Hope that helps

Move dynpro field text from right side on yhe left.

Hi experts. I have a DDic field (char1 as chebox) on screen. I need to move the DDic text for this field from right side to the left side of the checkbox. How can I do it? Is it neccesary to split this one object into two? To create a new text field and handle it in program?
Thanks for your answer.

hi Mark,
in the Graphical Screen Painter you have to right click on the field and you'll have some helpful options...
ec

ABAP Substring function from right side

Hi,
I want a substring function in ABAP, which starts from right instead of left to display some character out of a complete string.
Suppose there is a variable zdatavar -
zdatavar = 'MyNameIsBush'.
zdatavar = zdatavar+4(2).
The above will start from the left.
I want some function which start from the right.
Your help will be greately appreciated.
Regards,
SC

Hi,
Please check if this is working.
REPORT Z0804.
DATA str TYPE STRING.
DATA str2 TYPE STRING.
str = 'MyNameIsBush'.
WRITE: / str.
PERFORM rsubstring
    USING
        str
        2
    CHANGING
        str2
WRITE: / str2.
FORM rsubstring
    USING
        str TYPE STRING
        len
    CHANGING
        out TYPE STRING
    DATA:
        strln TYPE i,
        l_offset TYPE i,
        l_len TYPE i
    strln = STRLEN( str ).
    if strln GE len.
    l_offset = strln - len.
    l_len = len.
    out = str+l_offset(l_len).
    endif.
ENDFORM.
result:
MyNameIsBush
sh
regards,
Xiang Li

I would like to convert former purchases to DRM free. Where did the tab on the right side of iTunes Store go. What's it labeled? Can I still do these upgrades?

I would like to convert former purchases to DRM free. Where did the tab on the right side of iTunes Store go. What's it labeled? Can I still do these upgrades? I've done some in the past and would like to do some more and can't figure out how anymore.

I would like to convert former purchases to DRM free. Where did the tab on the right side of iTunes Store go. What's it labeled? Can I still do these upgrades? I've done some in the past and would like to do some more and can't figure out how anymore.

Two noise from right side when open the mbp

Every time when I open the laptop, there are two sound like zi zi from right side of it, before the opening music, it sounds like reading the disc, is there something wrong with the computer?

No. The OS, when the MBP is started does a diagnostics check, testing the optical drive as a part of same. That is the sound and it is normal.
Ciao.

Remove zeros from right side

Hi all,
I want to remove zeros from right side.
like : if value is '0.055500000000E+04'.
then the output should be '0.0555'.
How can i get such output.
Plz help me....

Hi,
the problem here is u are dealing with a datatype of format F (i.e floating point ) and the output u desire is in packed format .
You cannot delete the zeros of such data typesas type F instead u can move them to the packed datatype and get the result.
do one thing declare a variable of type p and move the value of type f which u have right now to the variable u have declared as type p.
data : v_val type p decimals 4.
v_val = " <------ assign the type f to type p over here .
hope this helps .
regards,
vijay.

Shifting -ve sign from right side of a value to left side in an alv report

HI GURUS,
i'm doing an alv report which displays grand totals of numeric fields as well.
tab-othercost = itab-netwr - itab-wavwr - itab-kzwi2 - itab-kzwi5.
when othercost value is -ve, the -ve sign is cuming right to the value.
i'm using fm 'CLOI_PUT_SIGN_IN_FRONT' and shifting the -ve sign frm right to left of value.
L_FIELDCAT-FIELDNAME = 'OTHERCOST'.
L_FIELDCAT-TABNAME = 'TAB'.
L_FIELDCAT-SELTEXT_M = 'OTHER COST'.
L_FIELDCAT-COL_POS = 9.
L_FIELDCAT-DO_SUM = 'X'.
L_FIELDCAT-DATATYPE = 'CURR'.
APPEND L_FIELDCAT TO L_FIELDCAT.
CLEAR L_FIELDCAT.
but in the grandtotal value i'm getting -ve sign in the right side of value.
plz let me wht to do to change the sign in grnadtotal value as well...

Hi,
do all the calculations in a currency variable...and then finally move it to the character variable..
Also try commenting this line.
*L_FIELDCAT-DATATYPE = 'CURR'. "Commented
Ex..
DATA: v_netwr TYPE netwr.
DATA: v_netwr_c TYPE char20.
v_netwr = 100 - 200.
WRITE: v_netwr TO v_netwr_c CURRENCY 'USD'.
CALL FUNCTION 'CLOI_PUT_SIGN_IN_FRONT'
CHANGING
value = v_netwr_c.
WRITE: / v_netwr_c.
Thanks
Naren

Indent here with left indent changes tab position

I have a sheet set up with a left indent and then a bunch of tabs.
e.g.: Course #, Course description, then a set of eight tabs with dates
The course descriptions are twice as long this year and so I was using indent-to-here (because there are rules below, and shift-return pushes the rule below under the second line only). But the tabs don't line up. They are "looking" at the left indent and making an adjustment - if I increase the left indent then the tabs associated with the indent-to-here line move left (the bigger the left indent the further left they are from the tab position)
Why?
Why would anyone want that to be the default behavior?
I can fix it with a second para style, but it breaks the association between the two lines of the description and now requires manual updating in the future, instead of a simple indent-to-here substitution.
I'm just wondering why this happens, seems completely counter intuitive - tabs should always align!

Will: As you can see by the screenshot it's easily "solved" with a second style, my reason for writing is why is this happening? - is this a bug that needs to be reported to Adobe? I don't understand why an Indent Here (given a left Indent), would change the primary attributes of tabs (i.e. lining-up!)
Peter: Prefs trashed; happens on any/all docs; CS6 (8.0.2). [You are setting a left indent, and then using the Indent Here (Cmd\)??]
Anyone else able to recreate?
Appreciate the replies.
Em

How to change IM text box from right side to botto...

During a video call with most of my contacts, the IM text box is below the video box and at the bottom of the screen. However, when my son calls (on new Samsung S5) the IM text box is to the right of the video box and on the right side of my screen.
I prefer to have it at the bottom and would like to know how to change it.

I have seen both layouts posted here in screen shots. I think that this may be one of those things that changes magically according to window width. Try dragging the window to a wider or narrower aspect ratio.
This kind of thing should be an option, with an "auto" setting to preserve the current width-sensitive behavior for those who like it.
Sean Ellis - uses Skype chat for serious work
Click here to read my blog post on Skype 7 and basic principles of GUI design

Hi...I can't get a new window to come up when I click on the + sign at the little tab on the right side of the existing browser window. I also can not get a new window to come up when I click on "Control + T". Any suggestions? Thanks!

I would like to be able to open a new window by clicking on the little plus sign at the right side of the existing open browser window. I used to be able to do that and something unknown happened that has taken that ability away. Thanks!

You need to access the router and change the wifi network name from the default which right now is the router name (linksys, netgear ect).
You want to use WPA2 encryption and you want a password that for now is 1,2,3,4,5,6,7,8. (no , in there). Put the same on the guest network.
Don't setup the "N" network yet, just use the b,g,,n for now just to get it working.
Save those settings on the left pane on the router page on the bottom.
Go find the wireless with the name you put in, whatever you used.
Settings, wifi
Under choose a network the wifi you have just setup should be listed.
If its not there do this
Settings, cellular data.....is this an tion, is it on? Turn cellular data off if it's on. Then go back to settings, wifi and try that again.

Removing border / browser fill from right side of screen

I'm currently creating my very first website with Adobe Muse, the parallax scrolling effects work perfectly but i'm having the following issue:
When i'm previewing my website in the browser i can scroll to the right side and there is a 5cm/10cm grey border, i would like to get rid of it. "Horizontal scrolling must be disabled".
I think it has something to do with the rectangles/frames (1920x1080) i'm using for the images, but that is just speculation.
Any help would be greatly appreciated : )
Here are some screenshots:
Full website:
The Grey Border/Area:
My Page Properties:

Welcome to the forum!
I don't believe that there's a cheap fix for an expensive machine such as T43p. Do you have any warranty left?
Have you run PC-Doctor on all video aspects of the system?
Good luck and let us know.
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

Tactic 3D Sigma - No audio from right side using USB?

Just got my new Creative Sound Blaster Tactic 3D Sigma (phew, that's a mouthful) headset in the mail today. When I connect it to my laptop using the USB adapter, there is no audio from the right side, only the left. When I connect using analog, though, the headset works fine.
I'm on Windows 7 Professional 64-bit, and I have the latest Creative software and headset drivers installed.

Hmmm... sounds like something is wrong with the USB adapter. Did you purchase the headset direct through Creative Online Store or from your local electronics store? If you bought the headset from your local electronics store, please get in touch with them right away, these stores usually have a 30 day exchange policy.
If you purchased this through the Creative Online Store, please write to our Customer Support and ask for an RMA (Return Merchandise Authorization).

Change tabs position from right side to left side

Similar Messages

Maybe you are looking for