Change VDC type on n7k sup1
Hi.
I have a pair of Nexus 7010 with sup1 running 6.2(8)
There is default VDC only:
# sh vdc detail
Switchwide mode is m1 f1 m1xl f2 m2xl f2e f3
vdc id: 1
vdc name: nex7010-12
vdc state: active
vdc mac address: 40:55:39:23:1e:c1
vdc ha policy: RELOAD
vdc dual-sup ha policy: SWITCHOVER
vdc boot Order: 1
vdc create time: Tue Dec 20 11:23:37 2011
vdc reload count: 0
vdc uptime: 989 day(s), 22 hour(s), 10 minute(s), 34 second(s)
vdc restart count: 0
vdc type: Ethernet
vdc supported linecards: m1 f1 m1xl m2xl
I want to add N7K-F248XP-25E line card. So as I understand I should enter
(config)# vdc nex7010-11 id 1
(config-vdc)# limit-resource module-type m1 f1 m1xl m2xl f2e
And then insert line card. Is this right?
So my questions. Is this operation disruptive to traffic forwarding? Do I lost allocated interface and/or limit-resources after change VDC type and need to retype them again?
Hi insharie,
thanks for fast answer :)
My config:
Model
N7K-M148GT-11
N7K-M148GT-11
N7K-M148GT-11
N7K-M148GT-11
N7K-SUP1
N7K-SUP1
N7K-M108X2-12L
N7K-M108X2-12L
N7K-F132XP-15
So there is no F2 line cards.
I want to add F2e - N7K-F248XP-25E line card.
In "Cisco Nexus 7000 Series NX-OS VDC Configuration Guide":
"Beginning with Cisco NX-OS Release 6.2(2), F2e module type can exist with M1, M1XL, and M2XL module types in the same VDC."
And as I understand F2e will be working in Proxy Mode
"When you enter the limit-resource module-type command and it changes the F2e mode between the old VDC type and the new VDC type, you are prompted to enter the rebind interface command"
From the table "Table 7 VDC Types Impacted By F2e Proxy Mode" I do not see my case
Old VDC: M1,F1 --> New VDC: M1,F1,F2e
And can not figure out the impact.
Similar Messages
-
When i am changing the material type i am getting this msg. In Po items were deleted.
Change Material Type
The material type cannot be changed.
The reasons for this are:
Valuated stock exists (see valuation areas below).
However, account determination for the two material types differs.
(different account category reference or no valuation data defined)
Valuation area
1030
No open purchase order are there.hi
plz check mmbe for the stock
check for the open PR and PO in ME5A and me2m
then try Change material type
Material Type can be changed using transaction MMAM
Menu: - Logistics > Material Management > Material Master > Material > Change Material Type
u can also use MMZ2 to change material type and ind sec
Refer following link for the same;
http://www.sap123.com/showthread.php?t=21
regards
kunal -
Is there a way to change the type of hash for passwords in active direcroty?
I would like to know what type of hash used for active directory passwords and if there is a way to change the type of hash.
Hi,
Windows generates and stores user account passwords by using two different password representations, generally known as "hashes." When you set or change the password for a user account to a password that contains fewer than 15 characters, Windows generates
both a LAN Manager hash (LM hash) and a Windows NT hash (NT hash) of the password.
You can configure the type to only store the stronger NT hash of your password.
How to prevent Windows from storing a LAN manager hash of your password in Active Directory and local SAM databases
http://support.microsoft.com/kb/299656/en-us
Regards,
Mandy
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place. -
How can I change the type of column in matrix
I want to change the type of column in matrix to it_LINKED_BUTTON, so it can show the orange arrow
I added the column throw marketing documents (rows)
It's seems the default column type is it_Edit
is there a way of changing the column type
i tried the below code, but it did not work because the type property in a matrix column is readonly
mtx.Columns.Item(0).Type = SAPbouiCOM.BoFormItemTypes.it_LINKED_BUTTON
sincerely yours
Riade Aslehi don't want to add a new column
i want to change the column type of existing column in matrix, becuase it's bind to a field
beside that, i can not add column , if the matrix has rows in it
sincerely yours
Riade Asleh -
Itunes 10.6.1.7 problem: when I change the file "media type" from 'Music' to 'Podcast' the file disapears from ITUNES. I do this via (1) right click, (2) select 'Get Info', (3) select 'options' tab, and (4) change media type. What is the problem?
Hi Memalyn
Essentially, the bare issue is that you have a 500GB hard drive with only 10GB free. That is not sufficient to run the system properly. The two options you have are to move/remove files to another location, or to install a larger hard drive (eg 2TB). Drive space has nothing to do with SMC firmware, and usually large media files are to blame.
My first recommendation is this: download and run the free OmniDiskSweeper. This will identify the exact size of all your folders - you can drill down into the subfolders and figure out where your largest culprits are. For example, you might find that your Pictures folder contains both an iPhoto Library and copies that you've brought in from a camera but are outside the iPhoto Library structure. Or perhaps you have a lot of purchased video content in iTunes.
If you find files that you KNOW you do not need, you can delete them. Don't delete them just because you have a backup, since if the backup fails, you will lose all your copies.
Don't worry about "cleaners" for now - they don't save much space and can actually cause problems. Deal with the large file situation first and see how you get on.
Let us know what you find out, and if you manage to get your space back.
Matt -
Badi for changing Stock type in MIGO transaction
Hello ALL,
IS there any BADI or EXIT for changing stock type in MIGO when we are doing GR against PO then we need to change the Stock type to Unrestricted stock.
Please let me know.Awarded if useful.
Regardshi,
Look into the BADI MB_MIGO_BADI.
or
Exits:
MBCF0009 Filling the storage location field
MBCF0005 Material document item for goods receipt/issue slip
MBCF0006 Customer function for WBS element
MBCF0007 Customer function exit: Updating a reservation
MBCF0010 Customer exit: Create reservation BAPI_RESERVATION_CREATE1
MB_CF001 Customer Function Exit in the Case of Updating a Mat. Doc.
MBCF0002 Customer function exit: Segment text in material doc. item
MBCF0011 Read from RESB and RKPF for print list in MB26
Sirish -
Changing data types of fields in structures
Hello,
Currently we are working for upgrade to ECC 6.0 .
In some transactions we are using BAPI_MATERIAL_SAVEDATA to create material.
We have some additional fields in MARA and MARC table , which we fill using BAPI_TE_MARA and BAPI_TE_MARC structures.
In these structures we have different data types for fields earlier in 4.6C
Now this function module is only working if we change data types of fields in these structures only to char type. It is going for dump , if we maintain any other data type.
Could any body tell me why should we change for char data type ?
Regards,
SATYAHi,
Check enhancement category (Extras --> Enhancement Category) for structures before enhancement. For example, for BAPI_TE_MARA structure, enhancement category is given as character type or numeric type. That means you can add the fields of data type only C and N. No other data types are allowed. If you select as not classified then you can add any data type. This option plays important role while enhancement.
Regards,
Prasanth -
How to change material type and industrial sector of the exsisting material
Hi,
There is an issue where user wants to change material type and industrial sector of the exsisting material .Is it posible to do so??
IF not ,how can we delete that material from material master so that another material with same number and required material type and industrial sector can be created.
Points will be definitely rewarded.
Thanks
RohitHi Rohit,
You can change the material type in MMAM trxn code if the material dosenot conatain any open purchase requisitions, open reservations & open purchase orders. Also material stock should be zero.
Remember the new material type should have same attributes same as old material type.
OLD Material New Material
1) Standard Price 1) Standard Price
2) Manufacture part 2) Manufacture part
profile actvated profile actvated
3) Quantity & Value 3) Quantity & Value
Updation in all areas Updation in all areas
4) should have same GL 4) Should have same GL acs
acs
It is not possible to change Industry sector once created.
If you want to delete the Material, you can flag it in MM06 trxn code.
Reg,
Ashok
Dont forget to Assign points if useful. -
How to change set type attribute of a product
Hi ;
I created additional fields for products by using "COMM_ATTRSET". It created a table and functions but I dont know how to change this additional attributes.I cant use these attribute set functions because i dont know fragment_id yet. I think there must be a function encapsulates them.
Is there any BAPI to change set type attributes?
PS: In forums , I found an FM "COM_PRODUCT_MAINTAIN_MULT_API" but I think it hasnt been used anymore in CRM7.0
ThanksThanks for your reply ;
but FM 'COM_PRODUCT_UI_MAINTAIN' doesnt have any generic import parameters to send my data to it in form of newly created attribute set type table "ZPRODUCT".
I want to set some fields of ZPRODUCT and i need to send them in this structure, this table has column FRG_ID , if you set an additional parameter for the first time , it generates new GUID..I think 'COM_PRODUCT_UI_MAINTAIN' generates this GUID but i dont know how to use it.
Can you give an example about using this FM? -
Error value = 73, How to change the type of password?
I want to use the famous wiki integrated in leopard, so I had to configure open directory and DNS.
Well my problem come from that I can't configure open Directory, just after creating a new admin, I have no possiblity to change the type of password, there is just the type shadow, and I know that we had to choose open directory's type.
Obviously, I'm authenticated in the workgroup manager
Which services I had to turn on to use open directory's type?
Or which mac I have to hit.
THXHi
So I had to configure open directory and DNS
What did you do or not do exactly?
My problem come from that I can't configure open Directory
You won't be able to configure Open Directory to allow different password types unless you either bind your Server to an existing KDC or make your Server the KDC. For the Server to be a KDC (Kerberos Distribution Center) it has to be an Open Directory Master. Successful promotion to an Open Directory Master Role absolutely depends on a correctly configured and running DNS Service - either on the server itself or on another server on the same network.
There are plenty of posts in these forums outlining how to configure your Server in terms of DNS as well as how to promote to Open Directory Master. Apple themselves make available Admin Manuals that should assist:
http://images.apple.com/server/macosx/docs/OpenDirectory_Adminv10.5.pdf
http://images.apple.com/server/macosx/docs/NetworkServices_Adminv10.5.pdf
Failing this these forums (as already mentioned) as well as:
http://www.afp548.com
Hope this helps, Tony -
How to change data type of content type column.
Hi all,
I am having one content type. I have 10 columns in it. There are two rich text columns in my content type. I have attached this content type to pages library. I want to change the data type of this rich text column to "Full
HTML content with formatting and constraints for publishing".
Please assist me with this issue.
amolHi,
From your description, my understanding is that you want to change the data type for rich text column in content type.
The field type of Full HTML content with formatting and constraints for publishing is "Invalid", you could refer to this article:https://msdn.microsoft.com/en-us/library/microsoft.sharepoint.spfieldtype.aspx.
You also could test it by create a Full HTML content with formatting and constraints for publishing column and get the its type with C# code below:
//change the URL to your SharePoint site
using (SPSite site = new SPSite("http://sp/sites/sharepoint2013"))
using (SPWeb web = site.OpenWeb())
SPFieldType type = web.Fields["Column name"].Type;
I have tested it with the PowerShell, it cannot hange the rich text column to “Full HTML content with formatting and constraints for publishing” column. If you want to edit the rich text column, you could not change the type of the column as the screenshot
below:
As a workaround, you could follow these steps to accomplish your requirement:
Create a “Full HTML content with formatting and constraints for publishing” type column in the content type.
Enter your site columns by clicking gear icon -> Site Settings -> Site columns under Web Designer Galleries under section.
Find and delete the rich text column you want to change.
Find the column you have created in step 1, and change the column’s name to the name of the text column you have deleted in step 3.
But you will lose the data of the rich text column in pages library with this method.
Best Regards,
Vincent Han
TechNet Community Support
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact
[email protected] -
How to change your type of ipod in itunes
How can you change your type of ipod in itunes. We purchased a new Ipod touch and the computer/itunes will not reconize it.
Try:
iPhone, iPad, or iPod touch: Device not recognized in iTunes for Windows
Make sure you have iTunes version 10.5 -
How to change data type of attribute in caf
hi.
this is my problem.
i been added a attribute in an entity service called emloyee. named "Birthday", use the data type "com.sap.caf.core.date".
when i tried modify the entity service, i hit exception about "DST Daylight Saving Time".
because of DST, the date will add an hour such like "1957/04/01 00:00:00.0" to "1957/04/01 01:00:00.0", and com.sap.caf.core.date will throw an exception.
is anyone had same problem like me?
how to fixed it(if passable)?
and, how to change data type?
thanks.Hi Sruthi,
all you need to do on this is open the report go to the parameters, select the parameter that you wish to change and click "Edit". This will allow you to change thefield to a date rather than a date time.
Regards,
Noel -
How to change content-type in receiver mail adapter
Hi,
I have receiver mail adapter for sending XML file as attachment in the mail. My partner expects to receive mail with content-type: text/xml, but XI sends Content-Type: application/xml. Please advise how I can change content-type to text/xml.
Thank you
Levhi,
try MessageTransformBean
Transform.ContentType
http://help.sap.com/saphelp_nw04/helpdata/en/57/0b2c4142aef623e10000000a155106/content.htm
also shown in my blog:
/people/michal.krawczyk2/blog/2005/11/23/xi-html-e-mails-from-the-receiver-mail-adapter
Regards,
michal
<a href="/people/michal.krawczyk2/blog/2005/06/28/xipi-faq-frequently-asked-questions"><b>XI / PI FAQ - Frequently Asked Questions</b></a> -
I'm running Mac OS X Version 10.7.4 on my iMac and am suddenly unable to simply move files to the trash.
Instead, I get the following message: 'Finder wants to make changes. Type your password to allow this.'
When I do enter my password, the file does not enter the Trash but seems to disappear.
I tried to find ways to revert to previous settings that allowed me to move files to the trash, but had trouble doing so.
How can I get my iMac to run normally?
Cheers!
Maybe you are looking for
-
I just bought a new computer with windows 8. I have 2 other computers (windows 7) authorized for itunes. When I go to manage your account the only choice I am give is to deauthorize all computers. There is no place from which to authorize this new co
-
Aperture unable to play slideshows since updating to Yosemite and 3.6
Hi, I updated yesterday to Yosemite and to Aperture 3.6 accordingly, and Aperture has been unable to play slideshows since then. It crashes abruptly whenever trying to play a slideshow from a project (though NOT from an album - weird). Same happens o
-
Regarding issues connecting to EJB 2 from OSB
Hi, I am trying to connect from OSB 11g to EJB 2 which is deployed on weblogic 7.1. I am getting this error. <soapenv:Envelope xmlns:soapenv="http://schemas.xmlsoap.org/soap/envelope/"> <soapenv:Body> <soapenv:Fault> <faultcode>soapenv:Server</faultc
-
Resource consumption for increasing column size
Hello, DB: 11.2.0.1.0 We need to increase the size of a column in the huge table (~ 400 Gb) from NUMBER(9) to NUMBER(18). Could you tell me what's the internals of the command alter table foo modify (bar NUMBER (18))Will it change the dictionary only
-
Trigger an error from EXIT_SAPLMLSR_001
I've been tasked with detecting whether or not the reference number is being repeated for a given vendor in any previous Entry Sheet during sheet creation in ML81N. If the reference number duplication is discovered the SAVE is supposed to be stoppe