Cisco 3945E ISR G2 as a wholesale VOIP gateway
we have unused 2 ISRG2 3945E router. we want to utilize this 2 router in our wholesale VoIP business.
i'm little bit confised. that how much concurent calls support each of this two router.
1Gbps backbone between the switch and router? Where can I find the information?
Go HERE.
The interface communication between router-to-module may be 1 Gbps but you won't be able to push 1 Gbps.
Similar Messages
-
Cisco Call Manager 5.1 and Cisco VoIP Gateways
Hi,
I have Cisco Call Manager 5.1 with Cisco 2800 series routers as a ISDN gateways and Cisco VG224/ATA 186 as POTS gateways. While Cisco Call Manager collects call statistics from 7900 series SCCP handsets managed by the Call Manager (number of VoIP packets, dropped frames etc.), it shows only one side of the call as it does not collect statistics from the Cisco routers (configured as H.323 gateways), the Cisco VG224 (with ports configured as H.323 gateways and as a SCCP devices) and Cisco ATA 186 (configured for SCCP).
Is the collection of these statistics possible? What needs to be done?
Thanks,
PaulUpdate: Logging of QoS/Call Management Records (CMR) to Call Manager CDR database is not possible with H.323 gateways; only MGCP gateways:
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_qanda_item09186a008020650a.shtml#qa4
Anyone know how to get the Cisco router gateway to log these statistics anyway using standard router logging mechanisms (e.g. syslog)?
Anyone know about calls to SCCP ports on Cisco VG224 or ATA 186?
Thanks,
Paul -
Cisco BRAS 7206 VXR + voip gateways Micronet (part 2)
I'm sorry, I've closed previouse discussion - https://supportforums.cisco.com/message/3075308#3075308
The problem is actual yet.
Micronet voip gateway (SP5002) cant' up pppoe connection to CIsco 7206 vxr, after cisco uptime > 20 days.
I have attached wireshark dump.
IOS: c7200-advipservicesk9-mz.122-33.SRD4.bin
Config:
Current configuration : 12976 bytes
! Last configuration change at 16:14:26 KGST Tue May 18 2010 by tuxper
! NVRAM config last updated at 16:25:21 KGST Tue May 18 2010 by tuxper
version 12.2
service timestamps debug uptime
service timestamps log datetime msec localtime
service password-encryption
service counters max age 5
hostname Router_PPPoE
boot-start-marker
boot system disk2:c7200-advipservicesk9-mz.122-33.SRD4.bin
boot-end-marker
logging buffered 64000
no logging console
enable password 7 071D294A4D101F1F1E140C061C382D74716B
aaa new-model
aaa group server radius PPPOE-RADIUS-SERVER
server-private xxx.x.x.x auth-port 3812 acct-port 3813 key 7 yyyyyyyyy
aaa group server radius ISG-RADIUS-SERVER
server-private xx.x.x.x auth-port 4812 acct-port 4813 key 7 yyyyyyyyyy
aaa group server radius CISCO-AAA-SERVER
server-private xxx.x.x.x auth-port 2812 acct-port 2813 key 7 yyyyyyyyyyyyyy
aaa group server tacacs+ ACCT-TACACS-SERVER
server-private xx.x.x.x key 7 yyyyyyyyyyyyyyyyy
aaa authentication login default local group CISCO-AAA-SERVER
aaa authentication enable default group CISCO-AAA-SERVER enable
aaa authentication ppp PPPoE group PPPOE-RADIUS-SERVER
aaa authorization network PPPoE group PPPOE-RADIUS-SERVER
aaa authorization subscriber-service default local group ISG-RADIUS-SERVER
aaa accounting update periodic 1440
aaa accounting exec default start-stop group CISCO-AAA-SERVER
aaa accounting commands 1 default stop-only group ACCT-TACACS-SERVER
aaa accounting commands 15 default stop-only group ACCT-TACACS-SERVER
aaa accounting network PPPoE start-stop group PPPOE-RADIUS-SERVER
aaa accounting network ISG start-stop group ISG-RADIUS-SERVER
aaa server radius dynamic-author
client xxx.x.x.x server-key 7 yyyyyyyyyyyyy
auth-type all
ignore session-key
ignore server-key
aaa session-id common
clock timezone KGST 6
ip subnet-zero
ip source-route
ip cef
ip name-server xxxxxxxxx
ip name-server xxxxxxxxx
subscriber service password 7 xxxxxxxxxxxxxxxx
redirect server-group REDIR-SERVER
server ip xxx.xxx.xxx.xxx port 9999
multilink bundle-name authenticated
archive
log config
logging enable
notify syslog contenttype plaintext
hidekeys
path ftp://[email protected]/bras7206-//[email protected]/bras7206-
write-memory
time-period 10080
username tuxper password 7 yyyyyyyyyyyy
username evrey password 7 yyyyyyyyyyyyy
bba-group pppoe global
virtual-template 1
sessions max limit 8000
sessions per-vlan limit 4000
interface Loopback0
ip address xx.xxx.xx.xx 255.255.255.255
interface GigabitEthernet0/1
description 7600_Uplink
ip address yy.yy.yy.yy 255.255.255.252
ip ospf network point-to-point
media-type rj45
speed 1000
duplex full
no negotiation auto
no cdp enable
interface GigabitEthernet0/2
description 7600_Uplink_pppoe_vlan
mtu 9000
no ip address
media-type rj45
speed auto
duplex auto
no negotiation auto
vlan-range dot1q 25 26
pppoe enable group global
exit-vlan-config
vlan-range dot1q 300 399
pppoe enable group global
exit-vlan-config
vlan-range dot1q 401 461
pppoe enable group global
exit-vlan-config
vlan-range dot1q 600 620
pppoe enable group global
exit-vlan-config
vlan-id dot1q 20
pppoe enable group global
exit-vlan-config
interface GigabitEthernet0/3
no ip address
shutdown
media-type rj45
speed auto
duplex auto
no negotiation auto
interface Virtual-Template1
description PPPoE
mtu 1492
ip unnumbered Loopback0
ppp authentication chap pap PPPoE
ppp authorization PPPoE
ppp accounting PPPoE
ppp eap refuse
ppp ms-chap refuse
ppp ms-chap-v2 refuse
ppp ipcp dns zzz.zzz.zzz.zzz zzz.zzz.zzz.zzz
router ospf 1
router-id yyy.yy.yy.yy
log-adjacency-changes
summary-address ii.iii.ii.0 255.255.254.0
summary-address ttt.ttt.ttt.0 255.255.255.0
summary-address ttt.ttt.ttt.0 255.255.255.0
summary-address ttt.ttt.ttt.0 255.255.255.0
summary-address ttt.ttt.ttt.0 255.255.254.0
redistribute connected subnets
redistribute static subnets
network uuu.uuu.uuu.uuu 0.0.0.3 area 0
default-information originate
ip classless
no ip http server
no ip http secure-server
!line con 0
stopbits 1
line aux 0
stopbits 1
line vty 0 4
session-timeout 30
exec-timeout 60 0
length 0
international
line vty 5 15
ntp clock-period 17179974
ntp peer vvv.vvv.vvv.vvv
ntp peer vvv.vvvv.vvv.vvv
end
P.S. I'm ready to provide any needed information.I made config like this:
interface Virtual-Template1
description PPPoE
mtu 1492
ip unnumbered Loopback0
ppp authentication chap pap ms-chap ms-chap-v2 PPPoE
ppp authorization PPPoE
ppp accounting PPPoE
ppp eap refuse
ppp ipcp dns xxx.xx.xx.xx tt.tt.tt.tt
But the problem is actual.
I installed new IOS: c7200-advipservicesk9-mz.122-33.SRE1.bin
But 21 days is over, and I have the same problem.
I don't understand anything. -
Hello NetProf!
I'm repeating my request for help, mabey clearing a few things out.
1. We have a cisco 1760 router running CCME
2. Some connected to it cisco 79xx ip-phones
3. A third party gatekeeper - MikroTik router
4. Every device is logged in the gatekeeper, and every call i settled with the use of it.
5. We have a third party VoIP gateway - MultiTechs MultiVoIP - also registered in the gatekeeper.
6. Now the connections history:
a) when phoning from the gateway to cisco - everything works fine.
b) when phoning fromn cisco to the gateway - the connection failes - it looks like CISCO ISN'T FORWARDING ANY INDENTITY DATA - NO IP ADDRESS, AND H323-ID - GETS TO THE GATEWAY!!!!!
Please help!!
Michal PodoskiCheck if there are some known issues documented here:
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122relnt/1700/rn1700yj.htm -
Cisco Prime Infrastructure deployment through Cisco 3945 ISR
Dears,
I have Cisco 3945 ISR include module for the Cisco prime infrastructure.
I need to deploy the prime but when I connected monitor on the module I saw that it is looking for DHCP only.
Please can anyone support me with procedure to install the prime?
Should I install the ESXi on this module by make it boot from external device (USB, or CD drive)?
Your support is highly appreciated,
Regards,Duplicate post.
Go HERE. -
Cisco 881 ISR IPSec VPN Tunnel does not pass traffic from the vlan.
I have a cisco 881 ISR Router with a site-to-site IPsec vpn tunnel to a mikrotik device on the other end (I inherited this from my client). The tunnel is constructed properly and is up, however traffic does not pass or get routed to the FA4 interface. I see in my packet captures that it hits the vlan1 interface (vlans are required on the L2 ports) and does not pass to the tunnel.
This is my configuration:
141Kerioth#sh config
Using 3763 out of 262136 bytes
! Last configuration change at 01:02:41 UTC Mon May 26 2014 by admin
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname 141Kerioth
boot-start-marker
boot-end-marker
logging buffered 51200 warnings
aaa new-model
141Kerioth#do wr mem
^
% Invalid input detected at '^' marker.
141Kerioth#wr mem
Building configuration...
[OK]
141Kerioth#sh run
Building configuration...
Current configuration : 5053 bytes
! Last configuration change at 01:38:06 UTC Mon May 26 2014 by admin
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname 141Kerioth
boot-start-marker
boot-end-marker
logging buffered 51200 warnings
aaa new-model
aaa authentication login default local
aaa authentication ppp default local
aaa session-id common
memory-size iomem 10
crypto pki trustpoint TP-self-signed-580381394
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-580381394
revocation-check none
rsakeypair TP-self-signed-580381394
crypto pki certificate chain TP-self-signed-580381394
certificate self-signed 01
30820229 30820192 A0030201 02020101 300D0609 2A864886 F70D0101 05050030
30312E30 2C060355 04031325 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 35383033 38313339 34301E17 0D313430 35323231 38323333
365A170D 32303031 30313030 30303030 5A303031 2E302C06 03550403 1325494F
532D5365 6C662D53 69676E65 642D4365 72746966 69636174 652D3538 30333831
33393430 819F300D 06092A86 4886F70D 01010105 0003818D 00308189 02818100
B001A012 2CA6970C 0648798B 2A786704 84F2D989 83974B19 9B4287F2 4503D2C9
173F23C4 FF34D160 202A7565 4A1CE08B 60B3ADAE 6E19EE6E 9CD39E72 71F9650E
930F22FE C4441F9C 2D7DD420 71F75DFC 3CCAC94E BA304685 E0E62658 A3E8D01C
D01D7D6A 5AF0B0E6 3CF6AF3A B7E51F83 9BF6D38E 65254E1F 71369718 ADADD691
02030100 01A35330 51300F06 03551D13 0101FF04 05300301 01FF301F 0603551D
23041830 168014D6 24878F12 1FFADF2F 537A438E 6DD7FB6B D79E4130 1D060355
1D0E0416 0414D624 878F121F FADF2F53 7A438E6D D7FB6BD7 9E41300D 06092A86
4886F70D 01010505 00038181 00771667 FCA66002 8AB9E5FB F210012F C50B586F
9A9640BB 45B4CEFD 030A38C0 E610AAC8 B41EF3C4 E55810F9 B2C727CF C1DEFCF1
0846E7BC 1D95420E 5DADB5F8 EFE7EB37 B5433B80 4FF787D4 B1F2A527 06F065A4
00522E97 A9D2335C E83C4AE1 E68D7A41 9D0046A7 ADCC282B 7527F84D E71CC567
14EF37EA 15E57AD0 3C5D01F3 EF
quit
ip dhcp excluded-address 10.0.16.1
ip dhcp pool ccp-pool
import all
network 10.0.16.0 255.255.255.0
default-router 10.0.16.1
dns-server 8.8.8.8
lease 0 2
ip domain name kerioth.com
ip host hostname.domain z.z.z.z
ip name-server 8.8.8.8
ip name-server 4.2.2.2
ip cef
no ipv6 cef
license udi pid CISCO881-K9 sn FTX180483DD
username admin privilege 15 secret 4 CmmfIy.RPySmo4Q2gEIZ2jlr3J.bTBAszoe5Bry0z4c
username meadowbrook privilege 0 password 0 $8UBr#Ux
username meadowbrook autocommand exit
policy-map type inspect outbound-policy
crypto isakmp policy 1
encr 3des
authentication pre-share
group 5
crypto isakmp key 141Township address z.z.z.z
crypto isakmp keepalive 10
crypto ipsec transform-set TS esp-3des esp-sha-hmac
mode tunnel
crypto map mymap 10 ipsec-isakmp
set peer z.z.z.z
set transform-set TS
match address 115
interface Loopback0
no ip address
interface Tunnel1
no ip address
interface FastEthernet0
no ip address
interface FastEthernet1
no ip address
interface FastEthernet2
no ip address
interface FastEthernet3
no ip address
interface FastEthernet4
description $FW_OUTSIDE_WAN$
ip address 50.y.y.y 255.255.255.240
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
crypto map mymap
interface Vlan1
description $ETH_LAN$
ip address 10.0.16.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
ip tcp adjust-mss 1452
ip forward-protocol nd
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip nat inside source list 115 interface Vlan1 overload
ip nat inside source list 199 interface FastEthernet4 overload
ip nat inside source route-map nonat interface FastEthernet4 overload
ip route 0.0.0.0 0.0.0.0 50.x.x.x
access-list 110 deny ip 10.0.16.0 0.0.0.255 10.0.1.0 0.0.0.255
access-list 110 permit ip 10.0.16.0 0.0.0.255 any
access-list 115 permit ip 10.0.16.0 0.0.0.255 10.0.1.0 0.0.0.255
access-list 144 permit icmp host c.c.c.c host 10.0.1.50
access-list 144 permit icmp host p.p.p.p host 10.0.16.105
access-list 199 permit ip a.a.a.a 0.0.0.255 any
no cdp run
route-map nonat permit 10
match ip address 100
line con 0
no modem enable
line aux 0
line vty 0 4
access-class 1 in
exec-timeout 30 0
privilege level 15
transport preferred ssh
transport input ssh
line vty 5 15
access-class 23 in
privilege level 15
transport input telnet ssh
cns trusted-server all-agents x.x.x.x
cns trusted-server all-agents hostname
cns trusted-server all-agents hostname.domain
cns id hardware-serial
cns id hardware-serial event
cns id hardware-serial image
cns event hostname.domain 11011
cns config initial hostname.domain 80
cns config partial hostname.domain 80
cns exec 80
endWhy do you have following command on the PIX?
crypto map outside_map 40 set transform-set 165.228.x.x
Also you have this transform set on the PIX:
crypto ipsec transform-set 10.112.60.0 esp-aes-256 esp-sha-hmac
This does not match the transfor set on the router:
crypto ipsec transform-set tritest esp-3des esp-md5-hmac
Where are you using the access-list/route-map
101 ? -
MPLS CE support on Cisco 2800 ISR router
Hi all, could I ask you for some hints about MPLS CE support on Cisco 2800 ISR router today? I`m finding restrictions and recommendations for feature implementation. Do you have any cisco web site about them?
Thank you for your advice and/or hints.
PeterThanks for an answer. I need to use multi-VPN model on CE router, but with QoS on one physical CE-PE connection (e.g. Frame-Relay DLCI).However, all VPNs on CE router must be secured for each one. The solution is Multi-VRF service feature, but, however, with multi-DLCI model on Frame-Relay and QoS per DLCI. Now, I`m finding a scenario to provide multi-VPN model on CE router with single-DLCI model and single QoS per one DLCI for all VPNs. And that, MPLS CE feature on C2800 could be used, if possible.
So, I don`t know more about MPLS CE on C2800 and I don`t know make a result to propsed solution... -
Hi everyone,
I would like to inquire on how to deploy Cisco 2911 ISR routers to act as Firewall to protect segments of my network. We have more than 10 units of the said router on our branch and i would like to ask on how i can make it a Firewall, it is running on IOS with sec/k9 license.
Hope that anyone can help me with my problem.
Thank you very much in advance
Best Regards,
Jayson CruzHi Julio,
A good day its me again. My apologies to bother you again. May i ask for your advice regarding the set-up of my IOS Zone-Based Firewall via 2911 routers.
I have 2 2911 beanch routers with bgp peering on a WAN links to reach the branch. On the LAN interface of the said Branch Routers are the LAN segments configured via subinterface command and running HSRP with the other branch router.
How would i implement Zone-Based Firewall with HA without having drops because of asymetric routing. Im sorry since the configuration guide that you have sent me as so many options and configurations that i tend to be confusing on which one is another option and which one is prt of the previous procedure. I hope you could help me with this one as i need to implement it within this week.
Thanks you very much and I'm sorry for bothering you.
Thank you very much!
Jayson
Sent from Cisco Technical Support Android App -
Cisco 1760 and E1 to VoIP Gateway
Hello!
Recently we've developed a test VoIP network combined out of a verry differently branched devices. It's working quite well, excluding one part.
The problem occures when trying to call from a CCME Cisco IP phone registered in a gatekeeper to a MultiTechs Multivoip E1/VoIP gateway (which is connected to our PBX). In MvOIPs logs - I can focus Cisco Phone trying to connect using the correct codec, matching gateway prefix - BUT LEAVING NO IP ADDRESS OR H.323 ID. Mabey some ideas???
Network is H.323 based.
Thanks in advance.
MichaelHi Micheal,
Can your PBX see the digits being passed to it?
Thanks,
Erik -
Hello,
I'm trying to configure a CISCO 2901 Integrated Services Router with a Module VWIC3-1MFT-T1/E1 as a VoIP gateway.
I'd like to know if is it possible, and if there is a especific document in CISCO documentation explaining it.
I have the following escenary:
Inbound calls:
PSTN (ISDN) --> CISCO 2901 --> Asterisk (SIP PBX)
Outbound calls
Asterisk(SIP PBX) --> CISCO 2901 --> PSTN (ISDN)
I have found some documents which explains how to configure a SIP Trunk with registration
http://www.cisco.com/en/US/docs/ios-xml/ios/voice/cube_sipsip/configuration/xe-3s/asr1000/voi-sip-trunk-reg.html
And how to configure the VWIC3 module
http://www.cisco.com/en/US/docs/routers/access/interfaces/software/feature/guide/vd-t1e1_vwic3.html
I'm very new with CISCO and I don't know how to route calls from the module to the Ethernet interface, and if I need to do anything else.
Thanks in advance!
David Pinedo
Presence TechnologyFor ISDN you need to configure your T1/E1, plenty of material and also references/examples on CSC, a quick search will provide some basic config
http://www.cisco.com/en/US/partner/docs/voice_ip_comm/cucme/admin/configuration/guide/cmebasic.html
Search pri-group timeslots to get more examples.
Then you'll need to configure dial-peers for in/out calls, search cisco.com for dial-peer configuration and you'll get all the info you need on how to configure them.
HTH
java
if this helps, please rate
www.cisco.com/go/pdihelpdesk -
Can I add VOIP Gateway SPA2100-SU to the DMZ of Router BEFSR41 Ver 4 ?
I am having multiple problems with dropped calls; need to reboot my LinkSys VOIP Gateway and so on, and my VOIP provider has suggested the following: "Add your Gateway (the physical device I guess) to the DMZ of your router." We are trying to tell the Router to give this VOIP Gateway, which gets its IP address via DHCP from the router, to essentially give this Gateway carte blanche to any port or destination it wants. I have NO idea how to do this on the BEFSR41, which is a CA model with Version 4 appended to its model number ? Can anyone send me how to advice ? - Mike BRYAN Ottawa Canada PM me for my email.
(Edited post for guideline compliance. Thanks!)
Message Edited by JOHNDOE_06 on 01-22-2008 02:54 PMFirst thing is to assign a static IP on the WAN / Internet side of your SPA-2100 so that you can set that IP to the DMZ of the BEFSR41. If you are not sure how to assign a static IP address on the spa2100 or how to open the web interface of the spa2100 and befsr41, then you better refer to the KB articles from www.linksys.com/kb. Just type in something like spa2100 or befsr41.
By the way, you may also enable NAT mapping and NAT Keep alive in your spa2100 aside from opening / forwarding ports in the befsr41 (check out Answer ID 5242). Lastly, enabling Send Resp To Src Port in the spa2100 is another option to try (this is under Voice > SIP > NAT Support Parameters).
It really requires much reading for us beginners to fully understand these devices. I am happy that I learned how to use the KBase site of Linksys since it gives me useful info about their products. -
Supply Engaged tone to calls over Max Connection, with out VoIP Gateway
Hi
I am tring to provide an engaged tone to calls that have exceeded the Max connections on a dial-peer statement, back to the PBX, without running VoIP Gateway.
Any suggestions?
Thanks.That should be the way it works:
http://www.ciscotaccc.com/voice/showcase?case=K20699757
If it's a PRI connection run debug isdn q931 to see what's being sent to the PBX. Not sure what you mean by 'without running voip gateway' -
Hi,
Could you please any give me more information about VoIP gateway, and how to connect it with PBX and how to buy it and what is the price?
Thanks,
Mohamed ElDiebHello ToshibaJoe,
If your PBX doesn’t support SIP check with your manufacturer to see whether a SIP gateway, module or upgrade is available for your existing PBX, that would enable you to use Skype Connect/SIP.
Also, it is highly recommended that a Skype Connect certified device is used, to gaurantee all features and functions work. Following is a link to that lists all Skype Connect certified products:
http://www.tekvizionlabs.com/3rdpartyprograms/skype/skype_verified_products.php
Please let us know if you have further questions.
Thank you,
MariaA
Skype Enterprise Support -
Cisco 3945E Maximum Throughput Potential
Hi,
Am looking at purchasing a router that is capable of serving a WAN bearer at up to 1Gbps. The 3945E has had good reviews as a high throughput router but the datasheets suggests performance of 350Mbps. It also states that additional performance can be ensured by adding SPE modules. Does anyone know whether the 3945E could achieve up to 1Gbps with SPE modules?
If the 3945E can't achieve such performance, I would appreciate alternative model suggestions. The key features I am after are:
IPV4 and IPV6 support
L2tpV3 support
BGP
IP SLA
1Gb Copper Connections on-board with capability of at least 4 Ports
Regards
MikeHave you looked at the new 4451-X ISR?
Supposedly the same pricing as the 3945E, but with 1-2gpbs+ performance.
Also with very low impact when turning on features in comparision with the older ISR routers.
I saw a presentation about it on Cisco Live Virtual.
Edit: Sigh.. replying to a necro thread. :( -
Hi
Does my router 892 support Voip?
I wanted to create a ccna voice lab. Any advice would be great as regarding router 892 supporting Voip with CME
I have found 1 doc it states 892 router supports CME
http://ptgmedia.pearsoncmg.com/images/9781587132995/samplepages/1587132990.pdf
892 doesn't support DSP but then how it will support CME ?
Any advice will be great
Regards
Aateek Singh
Network engineer
Spooster IT ServicesHi.
That comes from my experience.
I have a 887VA (non Cube) which originally mounts 256 MB of ram.
I purchased a 512MB module and loaded an 880-voice image and now i have a fully operative CUCME .
This is my Router
Cisco 887VA (MPC8300) processor (revision 1.0) with 708608K/77824K bytes of memory.
Processor board ID FCZ1618C5KG
1 DSL controller
1 Ethernet interface
4 FastEthernet interfaces
1 ATM interface
1 Virtual Private Network (VPN) Module
256K bytes of non-volatile configuration memory.
125496K bytes of ATA CompactFlash (Read/Write)
System image file is "flash:c880voice-universalk9-mz.154-3.M1.bin"
HTH
Regards
Carlo
Maybe you are looking for
-
How do I clear out the measure data in a 10g cube?
Does anyone know of an OLAP feature that I could call to zero out the measures stored in the cube before I refresh from the source data? I'm new to Oracle OLAP, but I have some experience with Essbase and I have quite a bit of experience with Oracle
-
so I have everything setup, I basically published everything and created 3 ADR's in SCCM and I'm waiting for the sync to sccm, so far the sync keeps timing out, I'm guessing that might be normal at this point?? Sync failed: The operation has timed ou
-
My sister has an HP PSC 1315 connected to an older Dell. She noticed a problem while doing online banking; she downloads and prints the statement which is in pdf format. The banks logo will print but instead of printing the rest of the text it only
-
Logical multiply instead of pause trigger
Hello all! Can some one help me with gating counter with another one, i want to produce modulated timebase, first counter generate pulses in continuous mode, and another one does the same, but with lower frequency, for example f1 = 20Hz, f2 = 0,1 Hz.
-
URGENT: Strange behaviour! Help!
Hi All. When I run the enclosed program I am getting some strange behaviour. For instance, when I click on the EDIT button nothing happens, but when I click on the DELETE button everything is fine! And I can also not run the code in edit() directly a