Cisco ASA 5505 and DHCP Client Problems
Hi, i have a problem. I've connected my ASA appliance to an ADSL modem, and i dont get an DHCP address on the outside interface (e0/0). I use the asa-722-19.bin firmware.
I turned on the debugging for the DHCP client and could see that the ASA device was sending out broadcasts but a reply never came. Instead I connected the device to my internal network where the ASA got an address instantly.
I read somewhere that if I was to use ?ip address dhcp client-id fastethernet 0″, then I got an address from the ISP.
I tried looking for a similar command on the ASA5505 but I couldn?t find anything. I did however find a page on the Cisco site confirming my suspicions. It said some ISP?s require the client-id field of the DHCPDISCOVER request to be filled.
I've also read that this issue has beed fixed since a few weeks, now they have released version 7.2(2).22 where you can define ?dhcp-client client-id interface outside? in global configuration mode. Im running 7.2(2).19 and i cannot find any command like that in my appaiance. How do i fix my problem ? Or how do i get about recieving the 7.2(2).22 firmware update.
Regards !
Leif
Hi again! I thought I should share the solution that worked for me. I use software version 7.2(2) on this device. ASDM 5.2(2). In ASDM open configuration / Interfaces. Click in outside (my case 0/0) and press Edit. Then open the tab Advanced and set the correct Active Mac address. Fore some reason its empty by default and the ISP/modem don't like that. You will find the correct MAC address under the help menu / "About ASA". Im sure there is some another way to do this but this is a simple "how-to" that works with Swedens biggest ISP and their standard DSL modem.
When I used a Linksys DSL modem in bridge mode without the MAC address set I got an inside IP adress (192.168.x.x) from the modem to the ASA. After setting the MAC address I just had to do a renew and got the outside address right away. /Bjorn
(future users searchwords: no ip from isp, ASA 5505 and cable modem).
Similar Messages
-
Firewall Cisco ASA 5505 new interface license problem
Hi
I have one ASA 5505 with a Base License
The problem is when i want to use a new named interface the system says "With current License maximum number of named interfaces allowed is 3. Name cannot be set for this interface"
And the question is if with this base license the interface cannot be used or only cannot be named?
here the output of my firewall:
Cisco Adaptive Security Appliance Software Version 8.2(5)
Device Manager Version 6.4(5)
Hardware: ASA5505, 512 MB RAM, CPU Geode 500 MHz
Internal ATA Compact Flash, 128MB
BIOS Flash Firmware Hub @ 0xffe00000, 1024KB
Encryption hardware device : Cisco ASA-5505 on-board accelerator (revision 0x0)
Boot microcode : CN1000-MC-BOOT-2.00
SSL/IKE microcode: CNLite-MC-SSLm-PLUS-2.03
IPSec microcode : CNlite-MC-IPSECm-MAIN-2.05
0: Int: Internal-Data0/0 : address is e02f.6de6.7843, irq 11
1: Ext: Ethernet0/0 : address is e02f.6de6.783b, irq 255
2: Ext: Ethernet0/1 : address is e02f.6de6.783c, irq 255
3: Ext: Ethernet0/2 : address is e02f.6de6.783d, irq 255
4: Ext: Ethernet0/3 : address is e02f.6de6.783e, irq 255
5: Ext: Ethernet0/4 : address is e02f.6de6.783f, irq 255
6: Ext: Ethernet0/5 : address is e02f.6de6.7840, irq 255
7: Ext: Ethernet0/6 : address is e02f.6de6.7841, irq 255
8: Ext: Ethernet0/7 : address is e02f.6de6.7842, irq 255
9: Int: Internal-Data0/1 : address is 0000.0003.0002, irq 255
10: Int: Not used : irq 255
11: Int: Not used : irq 255
Licensed features for this platform:
Maximum Physical Interfaces : 8
VLANs : 3, DMZ Restricted
Inside Hosts : Unlimited
Failover : Disabled
VPN-DES : Enabled
VPN-3DES-AES : Enabled
SSL VPN Peers : 2
Total VPN Peers : 10
Dual ISPs : Disabled
VLAN Trunk Ports : 0
Shared License : Disabled
AnyConnect for Mobile : Disabled
AnyConnect for Cisco VPN Phone : Disabled
AnyConnect Essentials : Disabled
Advanced Endpoint Assessment : Disabled
UC Phone Proxy Sessions : 2
Total UC Proxy Sessions : 2
Botnet Traffic Filter : DisabledHi,
The ASA5505 has with Base License the limitation of 3 Vlan interface of which 1 is also limited in access (shown by the above output mentioning DMZ Restricted)
For an interface on the ASA to operate it must have a name with the command "nameif"
If you already have 3 Vlan interfaces in use then with this license you wont be able to configure 4th Vlan interface without getting a license that supports more interfaces. I guess that would be the Security Plus license.
I know that this has come as a surprise to several users that have posted here on the forums. I too think that its a needles "feature" in the ASA to limit the use of the device in such a way.
- Jouni -
Cisco ASA 5505 and comodo SSL certificate
Hey All,
I am having an issue with setting up the SSL certificate piece of the Cisco AnyConnect VPN. I purchased the certificate and installed it via the ASDM under Configuration > Remote Access VPN > Certificate Management > Identity Certificates. I also placed the CA 2 piece under the CA Certificates. I have http redirect to https and under my browser it is green.
Once the AnyConnect client installs and automatically connects i get no errors or anything. The minute I disconnect and try to reconnect again, I get the "Untrusted VPN Server Certificate!" which isn't true because the connection information is https://vpn.mydomain.com and the SSL Cert is setup as vpn.mydomain.com.
On that note it lists the IP address instead of the vpn.mydomain.com as the untrusted piece of this. Now obviously I don't have the IP address as part of the SSL cert, just the web address. On the web side I have an A record setup to go from vpn.mydomain.com to the IP address of the Cisco ASA.
What am I missing here? I can post config if anyone needs it.
(My Version of ASA Software is 9.0 (2) and ASDM Version 7.1 (2))It's AnyConnect version 3.0. I don't know about the EKU piece. I didn't know that was required. I will attach my config.
ASA Version 9.0(2)
hostname MyDomain-firewall-1
domain-name MyDomain.com
enable password omitted
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
passwd omitted
names
name 10.0.0.13.1 MyDomain-Inside description MyDomain Inside
name 10.200.0.0 MyDomain_New_IP description MyDomain_New
name 10.100.0.0 MyDomain-Old description Inside_Old
name XXX.XXX.XX.XX Provider description Provider_Wireless
name 10.0.13.2 Cisco_ASA_5505 description Cisco ASA 5505
name 192.168.204.0 Outside_Wireless description Outside Wireless for Guests
ip local pool MyDomain-Employee-Pool 192.168.208.1-192.168.208.254 mask 255.255.255.0
ip local pool MyDomain-Vendor-Pool 192.168.209.1-192.168.209.254 mask 255.255.255.0
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address Cisco_ASA_5505 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address Provider 255.255.255.252
boot system disk0:/asa902-k8.bin
ftp mode passive
clock timezone PST -8
clock summer-time PDT recurring
dns domain-lookup inside
dns server-group DefaultDNS
name-server 10.0.3.21
domain-name MyDomain.com
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network MyDomain-Employee
subnet 192.168.208.0 255.255.255.0
description MyDomain-Employee
object-group network Inside-all
description All Networks
network-object MyDomain-Old 255.255.254.0
network-object MyDomain_New_IP 255.255.192.0
network-object host MyDomain-Inside
access-list inside_access_in extended permit ip any4 any4
access-list split-tunnel standard permit host 10.0.13.1
pager lines 24
logging enable
logging buffered errors
logging asdm informational
mtu inside 1500
mtu outside 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-712.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (inside,outside) source static Inside-all Inside-all destination static RVP-Employee RVP-Employee no-proxy-arp route-lookup
object network obj_any
nat (inside,outside) dynamic interface
access-group inside_access_in in interface inside
route outside 0.0.0.0 0.0.0.0 XXX.XXX.XX.XX 1
route inside MyDomain-Old 255.255.254.0 MyDomain-Inside 1
route inside MyDomain_New_IP 255.255.192.0 MyDomain-Inside 1
route inside Outside_Wireless 255.255.255.0 MyDomain-Inside 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
action terminate
dynamic-access-policy-record "Network Access Policy Allow VPN"
description "Must have the Network Access Policy Enabled to get VPN access"
aaa-server LDAP_Group protocol ldap
aaa-server LDAP_Group (inside) host 10.0.3.21
ldap-base-dn ou=MyDomain,dc=MyDomainnet,dc=local
ldap-group-base-dn ou=MyDomain,dc=MyDomainnet,dc=local
ldap-scope subtree
ldap-naming-attribute sAMAccountName
ldap-login-password *****
ldap-login-dn cn=Cisco VPN,ou=Special User Accounts,ou=MyDomain,dc=MyDomainNET,dc=local
server-type microsoft
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
http server enable
http MyDomain_New_IP 255.255.192.0 inside
http redirect outside 80
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto ipsec security-association pmtu-aging infinite
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ca trustpoint LOCAL-CA-SERVER
keypair LOCAL-CA-SERVER
no validation-usage
no accept-subordinates
no id-cert-issuer
crl configure
crypto ca trustpoint VPN
enrollment terminal
fqdn vpn.mydomain.com
subject-name CN=vpn.mydomain.com,OU=IT
keypair vpn.mydomain.com
crl configure
crypto ca trustpoint ASDM_TrustPoint1
enrollment terminal
crl configure
crypto ca trustpool policy
crypto ca server
shutdown
crypto ca certificate chain LOCAL-CA-SERVER
certificate ca 01
omitted
quit
crypto ca certificate chain VPN
certificate
omitted
quit
crypto ca certificate chain ASDM_TrustPoint1
certificate ca
omitted
quit
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable outside client-services port 443
crypto ikev2 remote-access trustpoint VPN
telnet timeout 5
ssh MyDomain_New_IP 255.255.192.0 inside
ssh timeout 5
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
dynamic-filter updater-client enable
dynamic-filter use-database
dynamic-filter enable
ssl encryption rc4-sha1 aes128-sha1 aes256-sha1 3des-sha1 rc4-md5 des-sha1
ssl trust-point VPN outside
webvpn
enable outside
anyconnect-essentials
anyconnect image disk0:/anyconnect-macosx-i386-2.4.1012-k9.pkg 3
anyconnect image disk0:/anyconnect-linux-2.4.1012-k9.pkg 4
anyconnect image disk0:/anyconnect-win-3.1.01065-k9.pkg 5
anyconnect profiles MyDomain-employee disk0:/MyDomain-employee.xml
anyconnect enable
tunnel-group-list enable
group-policy DfltGrpPolicy attributes
dns-server value 10.0.3.21
vpn-tunnel-protocol ikev1 ikev2 l2tp-ipsec ssl-client
default-domain value MyDomain.com
group-policy MyDomain-Employee internal
group-policy MyDomain-Employee attributes
wins-server none
dns-server value 10.0.3.21
vpn-tunnel-protocol ssl-client
split-tunnel-policy tunnelspecified
split-tunnel-network-list value split-tunnel
default-domain value MyDomain.com
webvpn
anyconnect profiles value MyDomain-employee type user
username MyDomainadmin password omitted encrypted privilege 15
tunnel-group MyDomain-Employee type remote-access
tunnel-group MyDomain-Employee general-attributes
address-pool MyDomain-Employee-Pool
authentication-server-group LDAP_Group LOCAL
default-group-policy MyDomain-Employee
tunnel-group MyDomain-Employee webvpn-attributes
group-alias MyDomain-Employee enable
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:1c7e3d7ff324e4fd7567aa21a96a8b22
: end
asdm image disk0:/asdm-712.bin
asdm location MyDomain_New_IP 255.255.192.0 inside
asdm location MyDomain-Inside 255.255.255.255 inside
asdm location MyDomain-Old 255.255.254.0 inside
no asdm history enable -
So I have a weird problem that I'm hoping someone has a point in the right direction I can follow... At home I have a Cisco ASA 5505 - not very complex network some BCP configs and it's providing a NAT (PAT). I have a static IP and using a few RFC 1918 segments - like I said nothing earth shattering. I have a linksys E1200 802.11N WPA2 PSK - again pretty standard. I connect laptops, iPads, iPhones, Kindles, Androids no problem. Until recently my 60" Vizio had no issues using the network (wired or wireless). Now network is failing on the TV. I see it get to the FW and I can ping trace etc... to the TV. The FW logs show resets (log is below).
Now here is the real interesting part - if I turn the tether feature on my iPhone on and connect the TV to it - it works - what's even more interesting is if I then go back to the home network it all works again no problem until I reboot the TV... HELP!
Apr 19 15:34:09 192.168.10.254 %ASA-6-305011: Built dynamic TCP translation from inside:10.10.10.139/60657 to outside:68.162.222.142/57003
Apr 19 15:34:09 192.168.10.254 %ASA-6-302013: Built outbound TCP connection 61988 for outside:98.137.204.251/443 (98.137.204.251/443) to inside:10.10.10.139/60657 (68.162.222.142/57003)
Apr 19 15:34:09 192.168.10.254 %ASA-6-302014: Teardown TCP connection 61988 for outside:98.137.204.251/443 to inside:10.10.10.139/60657 duration 0:00:00 bytes 3689 TCP Reset-I
Apr 19 15:34:12 192.168.10.254 %ASA-6-305011: Built dynamic TCP translation from inside:10.10.10.139/60658 to outside:68.162.222.142/53332
Apr 19 15:34:12 192.168.10.254 %ASA-6-302013: Built outbound TCP connection 61989 for outside:98.137.204.251/443 (98.137.204.251/443) to inside:10.10.10.139/60658 (68.162.222.142/53332)
Apr 19 15:34:12 192.168.10.254 %ASA-6-305011: Built dynamic TCP translation from inside:10.10.10.139/37006 to outside:68.162.222.142/40015
Apr 19 15:34:12 192.168.10.254 %ASA-6-302013: Built outbound TCP connection 61990 for outside:98.136.10.32/443 (98.136.10.32/443) to inside:10.10.10.139/37006 (68.162.222.142/40015)
Apr 19 15:34:12 192.168.10.254 %ASA-6-302014: Teardown TCP connection 61989 for outside:98.137.204.251/443 to inside:10.10.10.139/60658 duration 0:00:00 bytes 3689 TCP Reset-I
Apr 19 15:34:12 192.168.10.254 %ASA-6-302014: Teardown TCP connection 61990 for outside:98.136.10.32/443 to inside:10.10.10.139/37006 duration 0:00:00 bytes 3689 TCP FINs
AHello ras,
As you mentioned the TV is sending a reset packet to the remote address. I will recommend you to create a capture of the traffic and review the traffic at the packet level to see a posible reason for the drop.
Here is how. Then you can download it to pcap format and uploaded to the forum for further analysis.
http://www.cisco.com/c/en/us/support/docs/security/asa-5500-x-series-next-generation-firewalls/110117-asa-capture-asdm-config.html
http://www.cisco.com/c/en/us/td/docs/security/asa/syslog-guide/syslogs/logmsgs.html#pgfId-6941209
Hope this information is helpful. -
Hello all thanks for looking,
I need to know how to setup my cisco asa 5505 as a vpn client to services like HMA or privateinternet and other paid VPN services. If someone else has already written a guide to this then that would be great. What I want to do is route all my secure traffice through the asa and have it go across the internet as encrypted VPN stuff and have my other stuff that does not need to be encrypted just go through to my other router.
Thanks in advance,If your remote end of the services in question support IPsec IKEv1 as the VPN type then, yes - the 5505 can be a client for that service. At that point it looks like a regular LAN-LAN VPN which is documented in many Cisco and 3rd party how-to documents.
-
Cisco ASA 5505 and Airport Extreme
We have an office that uses an Airport Extreme as part of the network. The Airport Extreme uses a Cisco ASA 5505 as its gateway. The Cisco provides site to site VPN capabilities with other remote offices. We just got this configuration partially working and it works great for outbound connections.
But I have been unable to get an inbound connection to machines that are behind the Airport Extreme.
The goal is to access machines behind the Airport Extreme by way of RDP and also for use as drive and printer shares.
What do I need to do on the Airport to achieve this goal?
Thank you,
LebbyLebby,
I suspect it's not the AX that's the problem but the Cisco router, no doubt you have NAT enabled on that so that any inbound connection not initiated from inside just get's blocked.
You'll need to configure NAT on the Cisco first.
Regards,
Shawn -
Cisco Asa 5505 and Layer 3 Switch With Remote VPN Access
i got today a new CISCO LAYER 3 Switch .. so here is my scenrio
Cisco Asa 5505
I
Outside == 155.155.155.x
Inside = 192.168.7.1
VPN POOL Address = 10.10.10.1 - 10.10.10.20
Layer 3 Switch Config
Vlan 2
interface ip address = 192.168.1.1
Vlan 2
interface ip address = 192.168.2.1
Vlan 2
interface ip address = 192.168.3.1
Vlan 2
interface ip address = 192.168.4.1
Vlan 2
interface ip address = 192.168.5.1
ip Routing
So i want My Remote Access VPN clients to access all this Networks. So Please can you give me a helpfull trick or Link to configure the rest of my routing
Thank You allWhen My Remote VPN is Connected , it reaches 192.168.7.2 of the Layer 3 VLan that's Connected to The ASA 5505 ,
But i can't reach the rest of the VLAN - example
192.168.1.1
192.168.1.2
192.168.1.3
192.168.1.4
192.168.1.5
But i can reach the Connected Interface Vlan to My ASA ..
So here i think iam miss configuration to my Route
Any Help Please this is urgent -
CIsco ASA 5505 and VPN licenses
Hi,
Cisco ASA 5505 comes with 10 VPN licenses in a standard configuration.
How those licenses are counted? Will I need a license per one IPSec SA?
If I have two site connected with LAN-to-LAN VPN with 10 subnets at one site, how many licenses will be taken? 10 - one per IPSec SA or just 1 - one per point-to-point VPN?
Thank you.
Regards,
AlexAlex,
In an ASA 5505, it should say something like this...when you do sh ver.
VPN Peers : 25
It means that you can have so many peers connecting to the ASA. Its not per IPSec SA.
Its a per tunnel license.
Rate this, if it helps!
Gilbert -
VPN Between Cisco ASA 5505 and Cisco Router 881
Hi All,
I want to interconnect two office to each other but i have trouble: Please see below my configuration: What is missing to finalize the configuration properly?
Cisco ASA 5505.
Version 8.4(3)
HQ-ASA5505(config)# crypto ikev1 policy 888
HQ-ASA5505(config-ikev1-policy)# authentication pre-share
HQ-ASA5505(config-ikev1-policy)# encryption 3des
HQ-ASA5505(config-ikev1-policy)# hash md5
HQ-ASA5505(config-ikev1-policy)# lifetime 86400
HQ-ASA5505(config-ikev1-policy)# group 2
HQ-ASA5505(config)# tunnel-group 1.1.1.1 type ipsec-l2l
HQ-ASA5505(config)# tunnel-group 1.1.1.1 ipsec-attributes
HQ-ASA5505(config-tunnel-ipsec)# ikev1 pre-shared-key test
HQ-ASA5505(config)#object network HQ-Users
HQ-ASA5505(config-network-object)#subnet 10.48.0.0 255.255.255.0
HQ-ASA5505(config)# object-group network HQ.grp
HQ-ASA5505(config-network-object-group)# network-object object HQ-Users
HQ-ASA5505(config)#object network FSP_DATA
HQ-ASA5505(config-network-object)#subnet 10.48.12.0 255.255.255.0
HQ-ASA5505(config)#object-group network FSP.grp
HQ-ASA5505(config-network-object-group)#network-object object FSP_DATA
HQ-ASA5505(config)#access-list VPN_to_FSP extended permit ip object-group HQ.grp object-group FSP.grp
HQ-ASA5505(config)# crypto ipsec ikev1 transform-set TS esp-3des esp-md5-hmac
HQ-ASA5505(config)# crypto map ouside_map 888 set ikev1 transform-set TS
HQ-ASA5505(config)# crypto map ouside_map 888 match address VPN_to_FSP
HQ-ASA5505(config)# crypto map ouside_map 888 set peer 1.1.1.1
HQ-ASA5505(config)# crypto map ouside_map 888 set pfs group2
HQ-ASA5505(config)# crypto ikev1 enable outside
HQ-ASA5505(config)# crypto map ouside_map interface outside
Router 881
Version 12.4
License Information for 'c880-data'
License Level: advipservices Type: Permanent
Next reboot license Level: advipservices
LAB_ROuter(config)#object-group network HQ
LAB_ROuter(config-network-group)#10.48.0.0 255.255.255.0
LAB_ROuter(config)#object-group network FSP
LAB_ROuter(config-network-group)#10.48.12.0 255.255.255.0
ip access-list extended FSP_VPN
permit ip object-group FSP object-group HQ
LAB_ROuter(config)#crypto isakmp policy 888
LAB_ROuter(config-isakmp)#encryption 3des
LAB_ROuter(config-isakmp)#authentication pre-share
LAB_ROuter(config-isakmp)#hash md5
LAB_ROuter(config-isakmp)#group 2
LAB_ROuter(config-isakmp)#lifetime 86400
LAB_ROuter(config)#crypto isakmp key test address 2.2.2.2
LAB_ROuter(config)#crypto ipsec transform-set TS esp-3des esp-md5-hmac
crypto map outside_map 888 ipsec-isakmp
set peer 2.2.2.2
set transform-set TS
match address FSP_VPN
interface fast4 --> Outside Interface (where public IP address is assigned)
crypto map outside_map
Thank you in advance for your prompt advice!If you do a show crypto map in the router you will see the VPN traffic to be "any to any".
This is due a known bug on Cisco routers. The router does not support object-groups network for the VPN traffic. Use a regular ACL instead. -
Hi all,
I need some help from someone who has experience with configuring VPN on ASA over 2Wire router setup as dmzplus.
Topology:
ASA 5505 ---- 2Wire (dmzplus) -------------- ( cloud ) -------------- 2Wire (dmzplus) ---- ASA 5505
BT is the ISP on both ends. Static IPs are currently forwarded to the firewalls on both ends (outside interface is DHCP client).
All other services are working as expected (static NAT for few ports and so on).
I have found on some other forums the solution is to setup router in full bridge mode and then configure PPPoE on ASA, but I am trying to avoid this (for few other reasons).
The weird thing is when I am trying to initiate tunnel traffic from site A I can see IKE peer responder from site B, but not the opposite.
IKE state is MM_WAIT_MSG2 so it’s not passing the phase one. What I also notice in the arp table despite only one IP is assigned per site, the BT router has IP one less than the public one.
So my questions are:
1. Do I missing something in the config?
2. Is it possible to setup VPN on ASA over dmzplus?
3. Does the BT PPPoA service will become PPPoE after changing 2Wire to bridge mode?
4. Is there any different workaround or alternative solution?
CONFIG (crypto policies and all different settings are mirrored on the other end so it doesn’t make sense to post both):
: Saved
ASA Version 8.2(5)
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.0.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
ftp mode passive
access-list outside_in extended permit object-group PRS_PORTS any host 1.1.1.10
access-list outside_in extended permit object-group CCTV_PORTS any host 1.1.1.10
access-list VPN_traffic extended permit ip 192.168.0.0 255.255.255.0 192.168.1.0 255.255.255.0
access-list no-nat extended permit ip 192.168.0.0 255.255.255.0 192.168.1.0 255.255.255.0
pager lines 24
logging enable
logging buffered debugging
logging asdm informational
mtu inside 1500
mtu outside 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list no-nat
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) tcp interface <omitted>
static (inside,outside) tcp interface <omitted>
static (inside,outside) tcp interface <omitted>
static (inside,outside) tcp interface <omitted>
static (inside,outside) tcp interface <omitted>
static (inside,outside) tcp interface <omitted>
static (inside,outside) tcp interface <omitted>
static (inside,outside) tcp interface <omitted>
static (inside,outside) tcp interface <omitted>
static (inside,outside) tcp interface <omitted>
static (inside,outside) tcp interface <omitted>
access-group outside_in in interface outside
route outside 0.0.0.0 0.0.0.0 1.1.1.9 1 (points
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication enable console LOCAL
aaa authentication ssh console LOCAL
aaa authentication http console LOCAL
http server enable
http 192.168.1.0 255.255.255.0 inside
http 192.168.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set L2LVPN esp-3des esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map L2LCRYPTO 10 match address VPN_traffic
crypto map L2LCRYPTO 10 set peer 2.2.2.10
crypto map L2LCRYPTO 10 set transform-set L2LVPN
crypto map L2LCRYPTO interface outside
crypto ca trustpoint ASDM_TrustPoint0
enrollment self
subject-name CN=ciscoasa
crl configure
crypto ca certificate chain ASDM_TrustPoint0
certificate 569bb150
<omitted>
quit
crypto isakmp identity address
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
telnet timeout 5
ssh <omitted>
ssh timeout 15
console timeout 0
management-access inside
dhcpd dns 194.72.0.98 194.74.65.68
dhcpd auto_config outside
dhcpd address 192.168.0.2-192.168.0.33 inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ntp server 84.45.87.84 source outside prefer
webvpn
tunnel-group <2.2.2.10> type ipsec-l2l
tunnel-group <2.2.2.10> ipsec-attributes
pre-shared-key *****
isakmp keepalive threshold 100 retry 2
ISAKMP debug:
Feb 19 03:25:25 [IKEv1 DEBUG]: IP = <dest_ip>, IKE SA MM:8021bed6 terminating: flags 0x01000022, refcnt 0, tuncnt 0
Feb 19 03:25:25 [IKEv1 DEBUG]: IP = <dest_ip>, sending delete/delete with reason message
Feb 19 03:25:28 [IKEv1]: IP = <dest_ip>, IKE_DECODE RESENDING Message (msgid=0) with payloads : HDR + SA (1) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 128
Feb 19 03:25:33 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
Feb 19 03:25:33 [IKEv1]: IP = <dest_ip>, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.
Feb 19 03:25:33 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
Feb 19 03:25:33 [IKEv1]: IP = <dest_ip>, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.
Feb 19 03:25:36 [IKEv1]: IP = <dest_ip>, IKE_DECODE RESENDING Message (msgid=0) with payloads : HDR + SA (1) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 128
Feb 19 03:25:44 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
Feb 19 03:25:44 [IKEv1]: IP = <dest_ip>, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.
Feb 19 03:25:44 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
Feb 19 03:25:44 [IKEv1]: IP = <dest_ip>, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.
Feb 19 03:25:44 [IKEv1]: IP = <dest_ip>, IKE_DECODE RESENDING Message (msgid=0) with payloads : HDR + SA (1) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 128
Feb 19 03:25:52 [IKEv1 DEBUG]: IP = <dest_ip>, IKE MM Responder FSM error history (struct &0xc6dc3588) <state>, <event>: MM_DONE, EV_ERROR-->MM_WAIT_MSG3, EV_TIMEOUT-->MM_WAIT_MSG3, NullEvent-->MM_SND_MSG2, EV_SND_MSG-->MM_SND_MSG2, EV_START_TMR-->MM_SND_MSG2, EV_RESEND_MSG-->MM_WAIT_MSG3, EV_TIMEOUT-->MM_WAIT_MSG3, NullEvent
Feb 19 03:25:52 [IKEv1 DEBUG]: IP = <dest_ip>, IKE SA MM:a22d74b8 terminating: flags 0x01000002, refcnt 0, tuncnt 0
Feb 19 03:25:52 [IKEv1 DEBUG]: IP = <dest_ip>, sending delete/delete with reason message
Feb 19 03:25:54 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
Feb 19 03:25:54 [IKEv1]: IP = <dest_ip>, IKE Initiator: New Phase 1, Intf inside, IKE Peer <dest_ip> local Proxy Address 192.168.0.0, remote Proxy Address 192.168.1.0, Crypto map (L2LCRYPTO)
Feb 19 03:25:54 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
Feb 19 03:25:54 [IKEv1]: IP = <dest_ip>, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.
Feb 19 03:25:54 [IKEv1 DEBUG]: IP = <dest_ip>, constructing ISAKMP SA payload
Feb 19 03:25:54 [IKEv1 DEBUG]: IP = <dest_ip>, constructing NAT-Traversal VID ver 02 payload
Feb 19 03:25:54 [IKEv1 DEBUG]: IP = <dest_ip>, constructing NAT-Traversal VID ver 03 payload
Feb 19 03:25:54 [IKEv1 DEBUG]: IP = <dest_ip>, constructing NAT-Traversal VID ver RFC payload
Feb 19 03:25:54 [IKEv1 DEBUG]: IP = <dest_ip>, constructing Fragmentation VID + extended capabilities payload
Feb 19 03:25:54 [IKEv1]: IP = <dest_ip>, IKE_DECODE SENDING Message (msgid=0) with payloads : HDR + SA (1) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 168
Feb 19 03:25:57 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
Feb 19 03:25:57 [IKEv1]: IP = <dest_ip>, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.
Feb 19 03:26:02 [IKEv1]: IP = <dest_ip>, IKE_DECODE RESENDING Message (msgid=0) with payloads : HDR + SA (1) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 168
Feb 19 03:26:07 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
Feb 19 03:26:07 [IKEv1]: IP = <dest_ip>, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.
Feb 19 03:26:10 [IKEv1]: IP = <dest_ip>, IKE_DECODE RESENDING Message (msgid=0) with payloads : HDR + SA (1) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 168
Feb 19 03:26:17 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
Feb 19 03:26:17 [IKEv1]: IP = <dest_ip>, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.
Feb 19 03:26:18 [IKEv1]: IP = <dest_ip>, IKE_DECODE RESENDING Message (msgid=0) with payloads : HDR + SA (1) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 168
Feb 19 03:26:26 [IKEv1 DEBUG]: IP = <dest_ip>, IKE MM Initiator FSM error history (struct &0xc6aa7940) <state>, <event>: MM_DONE, EV_ERROR-->MM_WAIT_MSG2, EV_RETRY-->MM_WAIT_MSG2, EV_TIMEOUT-->MM_WAIT_MSG2, NullEvent-->MM_SND_MSG1, EV_SND_MSG-->MM_SND_MSG1, EV_START_TMR-->MM_SND_MSG1, EV_RESEND_MSG-->MM_WAIT_MSG2, EV_RETRY
Feb 19 03:26:26 [IKEv1 DEBUG]: IP = <dest_ip>, IKE SA MM:2e549563 terminating: flags 0x01000022, refcnt 0, tuncnt 0
Feb 19 03:26:26 [IKEv1 DEBUG]: IP = <dest_ip>, sending delete/delete with reason message
Feb 19 03:26:32 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
Feb 19 03:26:32 [IKEv1]: IP = <dest_ip>, IKE Initiator: New Phase 1, Intf inside, IKE Peer <dest_ip> local Proxy Address 192.168.0.0, remote Proxy Address 192.168.1.0, Crypto map (L2LCRYPTO)
Feb 19 03:26:32 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
Feb 19 03:26:32 [IKEv1]: IP = <dest_ip>, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.
Feb 19 03:26:32 [IKEv1 DEBUG]: IP = <dest_ip>, constructing ISAKMP SA payload
Feb 19 03:26:32 [IKEv1 DEBUG]: IP = <dest_ip>, constructing NAT-Traversal VID ver 02 payload
Feb 19 03:26:32 [IKEv1 DEBUG]: IP = <dest_ip>, constructing NAT-Traversal VID ver 03 payload
Feb 19 03:26:32 [IKEv1 DEBUG]: IP = <dest_ip>, constructing NAT-Traversal VID ver RFC payload
Feb 19 03:26:32 [IKEv1 DEBUG]: IP = <dest_ip>, constructing Fragmentation VID + extended capabilities payload
Feb 19 03:26:32 [IKEv1]: IP = <dest_ip>, IKE_DECODE SENDING Message (msgid=0) with payloads : HDR + SA (1) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 168
Feb 19 03:26:40 [IKEv1]: IP = <dest_ip>, IKE_DECODE RESENDING Message (msgid=0) with payloads : HDR + SA (1) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 168
Feb 19 03:26:43 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
Feb 19 03:26:43 [IKEv1]: IP = <dest_ip>, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.
Feb 19 03:26:43 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
Feb 19 03:26:43 [IKEv1]: IP = <dest_ip>, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.
no debug crypto isakmp 127 Feb 19 03:26:48 [IKEv1]: IP = <dest_ip>, IKE_DECODE RESENDING Message (msgid=0) with payloads : HDR + SA (1) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + NONE (0) totano debug crypto isakmp 127 Feb 19 03:26:53 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
Feb 19 03:26:53 [IKEv1]: IP = <dest_ip>, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.
Feb 19 03:26:53 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
Feb 19 03:26:53 [IKEv1]: IP = <dest_ip>, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.
Kind regards
MariuszHi all,
The latest update
I've finally managed to get the VPN to work! As soon as I've reconfigure the router and the firewall it took 1 second to establish the tunnel. So the answer for the most important question number 2. Is it possible to setup VPN on ASA over dmzplus? is no. I think the issue is related to routing which doesn't look normal with the dmzplus (can't properly traceroute to IPs etc)
So my solution was :
- changed 2Wire settings (Bridged LLC, ATM PVC disabled, Connection type: direct IP, save and uncheck Routing mode)
- changed ASA external interface settings to pppoe with automatic routing and IP
Regards
Mariusz -
Cisco ASA 5505 AnyConnect SSL VPN problem
Hi!
I have a small network, wiht ASA 5505, 8.4:
Inside network: 192.168.2.0/24
Outside: Static IP
I would like to deploy a SSL AnyConnect setup.
The state:
-I give the correct IP from my predefined VPN pool (10.10.10.0/24).
But, could not reach any resource, could not ping too. My host has given 10.10.10.1 IP, and I had a GW: 10.10.10.2. Where is this GW from?
Could you help me?
Here is my config (I omitted my PUBLIC IP, and GW):
Result of the command: "show running-config"
: Saved
ASA Version 8.4(4)1
hostname valamiASA
domain-name valami.local
enable password OeyyCrIqfUEmzen8 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
switchport access vlan 12
interface Vlan1
description LAN
no forward interface Vlan12
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
description WAN
nameif outside
security-level 0
ip address MY_STATIC_IP 255.255.255.248
interface Vlan12
description Vendegeknek a valamiHotSpot WiFi-hez
nameif guest
security-level 100
ip address 192.168.4.1 255.255.255.0
management-only
ftp mode passive
clock timezone GMT 0
dns domain-lookup inside
dns domain-lookup outside
dns domain-lookup guest
dns server-group DefaultDNS
name-server 62.112.192.4
name-server 195.70.35.66
domain-name valami.local
same-security-traffic permit intra-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network inside-net
subnet 192.168.2.0 255.255.255.0
object network guest-net
subnet 192.168.3.0 255.255.255.0
object network NETWORK_OBJ_192.168.2.128_25
subnet 192.168.2.128 255.255.255.128
object-group protocol DM_INLINE_PROTOCOL_3
protocol-object ip
protocol-object icmp
object-group protocol DM_INLINE_PROTOCOL_1
protocol-object ip
protocol-object icmp
object-group protocol DM_INLINE_PROTOCOL_2
protocol-object ip
protocol-object icmp
access-list global_access extended permit object-group DM_INLINE_PROTOCOL_3 any any
access-list AnyConnect_Client_Local_Print extended deny ip any any
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq lpd
access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 631
access-list AnyConnect_Client_Local_Print remark Windows' printing port
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 9100
access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.251 eq 5353
access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.252 eq 5355
access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 137
access-list AnyConnect_Client_Local_Print extended permit udp any any eq netbios-ns
access-list inside_access_in extended permit object-group DM_INLINE_PROTOCOL_2 any any
access-list outside_access_in extended permit object-group DM_INLINE_PROTOCOL_1 any any
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu guest 1500
ip local pool valami_vpn_pool 10.10.10.1-10.10.10.10 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
icmp permit any inside
no asdm history enable
arp timeout 14400
object network inside-net
nat (inside,outside) dynamic interface
object network guest-net
nat (guest,outside) dynamic interface
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
access-group global_access global
route outside 0.0.0.0 0.0.0.0 MY_STATIC_GW 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa local authentication attempts max-fail 16
http server enable
http 192.168.2.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
telnet timeout 5
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics host
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
enable inside
enable outside
anyconnect-essentials
anyconnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
anyconnect enable
tunnel-group-list enable
group-policy GroupPolicy_valami_VPN internal
group-policy GroupPolicy_valami_VPN attributes
wins-server value 192.168.2.2
dns-server value 192.168.2.2
vpn-tunnel-protocol ssl-client
split-tunnel-policy tunnelall
default-domain value valami.local
webvpn
anyconnect ssl rekey time 30
anyconnect ssl rekey method ssl
anyconnect ask enable default anyconnect timeout 30
customization none
deny-message value Login was successful, but because certain criteria have not been met or due to some specific group policy, you do not have permission to use any of the VPN features. Contact your IT administrator for more information.
username test password P4ttSyrm33SV8TYp encrypted
tunnel-group valami_VPN type remote-access
tunnel-group valami_VPN general-attributes
address-pool valami_vpn_pool
default-group-policy GroupPolicy_valami_VPN
tunnel-group valami_VPN webvpn-attributes
group-alias valami_VPN enable
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:d54de340bb6794d90a9ee52c69044753
: endFirst of all thanks your link.
I know your notes, but i don't understand 1 thing:
if i check nat exemption in the anyconnect wizad, why should i make nat exemption rule?
A tried creating a roule, but it is wrong.
My steps (on ASDM):
1: create network object (10.10.10.0/24), named VPN
2: create nat rule: source any, destination VPN, protocol any
Here is my config:
Result of the command: "show running-config"
: Saved
ASA Version 8.4(4)1
hostname companyASA
domain-name company.local
enable password OeyyCrIqfUEmzen8 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
switchport access vlan 12
interface Vlan1
description LAN
no forward interface Vlan12
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
description WAN
nameif outside
security-level 0
ip address 77.111.103.106 255.255.255.248
interface Vlan12
description Vendegeknek a companyHotSpot WiFi-hez
nameif guest
security-level 100
ip address 192.168.4.1 255.255.255.0
ftp mode passive
clock timezone CEST 1
clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00
dns domain-lookup inside
dns domain-lookup outside
dns domain-lookup guest
dns server-group DefaultDNS
name-server 62.112.192.4
name-server 195.70.35.66
domain-name company.local
same-security-traffic permit intra-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network inside-net
subnet 192.168.2.0 255.255.255.0
object network guest-net
subnet 192.168.3.0 255.255.255.0
object network NETWORK_OBJ_192.168.2.128_25
subnet 192.168.2.128 255.255.255.128
object network WEBSHOP
host 192.168.2.2
object network INSIDE_HOST
host 10.100.130.5
object network VOIP_management
host 192.168.2.215
object network Dev_1
host 192.168.2.2
object network Dev_2
host 192.168.2.2
object network RDP
host 192.168.2.2
object network Mediasa
host 192.168.2.17
object network VOIP_ePhone
host 192.168.2.215
object network NETWORK_OBJ_192.168.4.0_28
subnet 192.168.4.0 255.255.255.240
object network NETWORK_OBJ_10.10.10.8_29
subnet 10.10.10.8 255.255.255.248
object network VPN
subnet 10.10.10.0 255.255.255.0
object network VPN-internet
subnet 10.10.10.0 255.255.255.0
object-group protocol DM_INLINE_PROTOCOL_3
protocol-object ip
protocol-object icmp
object-group protocol DM_INLINE_PROTOCOL_1
protocol-object ip
protocol-object icmp
object-group protocol DM_INLINE_PROTOCOL_2
protocol-object ip
protocol-object icmp
access-list global_access extended permit object-group DM_INLINE_PROTOCOL_3 any any
access-list AnyConnect_Client_Local_Print extended deny ip any any
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq lpd
access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 631
access-list AnyConnect_Client_Local_Print remark Windows' printing port
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 9100
access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.251 eq 5353
access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.252 eq 5355
access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 137
access-list AnyConnect_Client_Local_Print extended permit udp any any eq netbios-ns
access-list inside_access_in extended permit object-group DM_INLINE_PROTOCOL_2 any any
access-list outside_access_in extended permit object-group DM_INLINE_PROTOCOL_1 any any
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu guest 1500
ip local pool company_vpn_pool 10.10.10.10-10.10.10.15 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
icmp permit any inside
no asdm history enable
arp timeout 14400
nat (any,any) source static any any destination static VPN VPN
nat (inside,outside) source static inside-net inside-net destination static VPN VPN
object network inside-net
nat (inside,outside) dynamic interface
object network guest-net
nat (guest,outside) dynamic interface
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
access-group global_access global
route outside 0.0.0.0 0.0.0.0 77.111.103.105 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa local authentication attempts max-fail 16
http server enable
http 192.168.2.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
telnet timeout 5
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics host
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
enable inside
enable outside
anyconnect-essentials
anyconnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
anyconnect enable
tunnel-group-list enable
group-policy GroupPolicy_company_VPN internal
group-policy GroupPolicy_company_VPN attributes
wins-server value 192.168.2.2
dns-server value 192.168.2.2
vpn-tunnel-protocol l2tp-ipsec
split-tunnel-policy tunnelall
default-domain value company.local
webvpn
anyconnect ssl rekey time 30
anyconnect ssl rekey method ssl
anyconnect ask enable default anyconnect timeout 30
customization none
deny-message value Login was successful, but because certain criteria have not been met or due to some specific group policy, you do not have permission to use any of the VPN features. Contact your IT administrator for more information.
group-policy GroupPolicy_VPN internal
group-policy GroupPolicy_VPN attributes
wins-server none
dns-server value 62.112.192.4 195.70.35.66
vpn-tunnel-protocol ssl-client
default-domain value company.local
username test password P4ttSyrm33SV8TYp encrypted
tunnel-group company_VPN type remote-access
tunnel-group company_VPN general-attributes
address-pool company_vpn_pool
default-group-policy GroupPolicy_company_VPN
tunnel-group company_VPN webvpn-attributes
group-alias company_VPN enable
tunnel-group VPN type remote-access
tunnel-group VPN general-attributes
address-pool company_vpn_pool
default-group-policy GroupPolicy_VPN
tunnel-group VPN webvpn-attributes
group-alias VPN enable
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
inspect icmp error
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:33ee37a3722f228f9be9b84ef43f731e
: end
Could you give me a CLI-code?
(or ASDM steps). -
S2S between Cisco ASA 5505 and Sonicwall TZ-170 but not able to ping across
Hi,
I am helping out a friend of mine with his Site-to-Site VPN between his companies Cisco ASA another company's SonicWall TZ-170. I have checked the screenshots proivded by the other end and tried to match with ours. The Tunnel shows but we are not able to Ping resources on the other end. The other side insists that the problem is on our end but I am not sure where the issue resides. Please take a look at our config and let me know if there is anything that I have missed. I am pretty sure I didn't but extra eyes may be of need here.
Our LAN is 10.200.x.x /16 and theirs is 192.168.9.0 /24
ASA Version 8.2(2)
terminal width 300
hostname company-asa
domain-name Company.com
no names
name 10.1.0.0 sacramento-network
name 10.3.0.0 irvine-network
name 10.2.0.0 portland-network
name x.x.x.x MailLive
name 192.168.9.0 revit-vpn-remote-subnet
dns-guard
interface Ethernet0/0
nameif outside
security-level 0
ip address x.x.x.x 255.255.255.128
interface Ethernet0/1
nameif inside
security-level 100
ip address 10.200.200.1 255.255.0.0
interface Ethernet0/2
nameif dmz
security-level 50
ip address 172.22.22.1 255.255.255.0
interface Ethernet0/3
description Internal Wireless
shutdown
nameif Wireless
security-level 100
ip address 10.201.201.1 255.255.255.0
interface Management0/0
shutdown
nameif management
security-level 100
no ip address
management-only
boot system disk0:/asa822-k8.bin
ftp mode passive
clock timezone PST -8
clock summer-time PDT recurring
dns domain-lookup outside
dns server-group DefaultDNS
domain-name company.com
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object-group network local_net_group
network-object 10.1.0.0 255.255.0.0
network-object 10.2.0.0 255.255.0.0
network-object 10.200.0.0 255.255.0.0
network-object 10.3.0.0 255.255.0.0
network-object 10.4.0.0 255.255.0.0
network-object 10.5.0.0 255.255.0.0
network-object 10.6.0.0 255.255.0.0
network-object 10.7.0.0 255.255.0.0
network-object 192.168.200.0 255.255.255.0
object-group network NACIO123
network-object 1.1.1.1 255.255.255.224
object-group service MAIL_HTTPS_BORDERWARE tcp
port-object eq smtp
port-object eq https
port-object eq 10101
object-group service SYSLOG_SNMP_NETFLOW udp
port-object eq syslog
port-object eq snmp
port-object eq 2055
object-group service HTTP_HTTPS tcp
port-object eq www
port-object eq https
object-group network OUTSIDECO_SERVERS
network-object host x.x.x.34
network-object host x.x.x.201
network-object host x.x.x.63
object-group network NO-LOG
network-object host 10.200.200.13
network-object host 10.200.200.25
network-object host 10.200.200.32
object-group service iPhoneSync-Services-TCP tcp
port-object eq 993
port-object eq 990
port-object eq 998
port-object eq 5678
port-object eq 5721
port-object eq 26675
object-group service termserv tcp
description terminal services
port-object eq 3389
object-group protocol TCPUDP
protocol-object udp
protocol-object tcp
object-group service DTI tcp
description DCS CONTROL PROTOCOL
port-object eq 3333
object-group service H.245 tcp
description h.245 signaling
port-object range 1024 4999
object-group service RAS udp
port-object eq 1719
port-object range 1718 1720
object-group service XML tcp
port-object range 3336 3341
object-group service mpi tcp
port-object eq 2010
object-group service mvp_control tcp
port-object eq 2946
object-group service rpc tcp-udp
port-object eq 1809
object-group service tcp8080 tcp
port-object eq 8080
object-group service tcp8011 tcp
port-object eq 8011
object-group service rtp_rtcp_udp udp
port-object range 1024 65535
object-group service ecs_xml tcp-udp
port-object eq 3271
object-group service rtp20000 udp
description 10000-65535
port-object range 20000 25000
port-object range 10000 65535
object-group service tcp5222 tcp
port-object range 5222 5269
object-group service tcp7070 tcp
port-object eq 7070
object-group network videoco
network-object host x.x.x.144
network-object host x.x.x.145
object-group service video tcp
port-object range 1718 h323
object-group service XML2 tcp-udp
port-object range 3336 3345
object-group service tcp_tls tcp
port-object eq 5061
object-group service Autodesk tcp
port-object eq 2080
port-object range 27000 27009
access-list outside_policy remark ====== Begin Mail From Postini Network ======
access-list outside_policy extended permit tcp x.x.x.x 255.255.240.0 host x.x.x.x eq smtp
access-list outside_policy extended permit tcp x.x.x.x 255.255.255.240 host x.x.x.x eq smtp
access-list outside_policy extended permit tcp x.x.x.0 255.255.240.0 host x.x.x.x eq smtp
access-list outside_policy remark ****** End Mail From Postini Network ******
access-list outside_policy remark ====== Begin Inbound Web Mail Access ======
access-list outside_policy extended permit tcp any host x.x.x.x object-group HTTP_HTTPS
access-list outside_policy remark ****** End Inbound Web Mail Access ******
access-list outside_policy remark ====== Begin iPhone Sync Rules to Mail Server ======
access-list outside_policy extended permit tcp any host x.x.x.x object-group iPhoneSync-Services-TCP
access-list outside_policy remark ****** End iPhone Sync Rules to Mail Server ******
access-list outside_policy remark ====== Begin MARS Monitoring ======
access-list outside_policy extended permit udp x.x.x.x 255.255.255.128 host x.x.x.x object-group SYSLOG_SNMP_NETFLOW
access-list outside_policy extended permit icmp x.x.x.x 255.255.255.128 host x.x.x.x
access-list outside_policy remark ****** End MARS Monitoring ******
access-list outside_policy extended permit tcp object-group NACIO123 host x.x.x.141 eq ssh
access-list outside_policy extended permit tcp any host x.x.x.x eq www
access-list outside_policy extended permit tcp any host x.x.x.x eq https
access-list outside_policy extended permit tcp any host x.x.x.x eq h323
access-list outside_policy extended permit tcp any host x.x.x.x range 60000 60001
access-list outside_policy extended permit udp any host x.x.x.x range 60000 60007
access-list outside_policy remark radvision 5110 port 80 both
access-list outside_policy extended permit object-group TCPUDP any object-group videoco eq www
access-list outside_policy remark radvision
access-list outside_policy extended permit tcp any object-group videoco object-group termserv
access-list outside_policy remark radvision 5110 port21 out
access-list outside_policy extended permit tcp any object-group videoco eq ftp
access-list outside_policy remark rad5110 port22 both
access-list outside_policy extended permit tcp any object-group videoco eq ssh
access-list outside_policy remark rad 5110 port161 udp both
access-list outside_policy extended permit udp any object-group videoco eq snmp
access-list outside_policy remark rad5110 port443 both
access-list outside_policy extended permit tcp any object-group videoco eq https
access-list outside_policy remark rad5110 port 1024-4999 both
access-list outside_policy extended permit tcp any object-group videoco object-group H.245
access-list outside_policy remark rad5110 port 1719 udp both
access-list outside_policy extended permit udp any object-group videoco object-group RAS
access-list outside_policy remark rad5110 port 1720 both
access-list outside_policy extended permit tcp any any eq h323
access-list outside_policy remark RAD 5110 port 3333 tcp both
access-list outside_policy extended permit tcp any object-group videoco object-group DTI
access-list outside_policy remark rad5110 port 3336-3341 both
access-list outside_policy extended permit object-group TCPUDP any object-group videoco object-group XML2
access-list outside_policy remark port 5060 tcp/udp
access-list outside_policy extended permit object-group TCPUDP any object-group videoco eq sip
access-list outside_policy remark rad 5110port 1809 rpc both
access-list outside_policy extended permit object-group TCPUDP any object-group videoco object-group rpc
access-list outside_policy remark rad 5110 port 2010 both
access-list outside_policy extended permit tcp any object-group videoco object-group mpi
access-list outside_policy remark rad 5110 port 2946 both
access-list outside_policy extended permit tcp any object-group videoco object-group mvp_control
access-list outside_policy extended permit tcp any object-group videoco object-group tcp8080
access-list outside_policy extended permit tcp any object-group videoco object-group tcp8011
access-list outside_policy remark 1024-65535
access-list outside_policy extended permit udp any object-group videoco object-group rtp_rtcp_udp
access-list outside_policy extended permit object-group TCPUDP any object-group videoco object-group ecs_xml
access-list outside_policy extended permit udp any object-group videoco object-group rtp20000
access-list outside_policy extended permit tcp any object-group videoco eq telnet
access-list outside_policy remark port 53 dns
access-list outside_policy extended permit object-group TCPUDP any object-group videoco eq domain
access-list outside_policy remark 7070
access-list outside_policy extended permit tcp any object-group videoco object-group tcp7070
access-list outside_policy remark 5222-5269 tcp
access-list outside_policy extended permit tcp any object-group videoco range 5222 5269
access-list outside_policy extended permit tcp any object-group videoco object-group video
access-list outside_policy extended permit tcp any object-group videoco object-group tcp_tls
access-list outside_policy remark ====== Begin Autodesk Activation access ======
access-list outside_policy extended permit tcp any any object-group Autodesk
access-list outside_policy remark ****** End Autodesk Activation access ******
access-list outside_policy extended permit tcp x.x.x.x 255.255.255.248 host x.x.x.x eq smtp
access-list outside_policy remark ****** End Autodesk Activation access ******
access-list inside_policy extended deny tcp host 10.200.200.25 10.1.0.0 255.255.0.0 eq 2967 log disable
access-list inside_policy extended deny tcp host 10.200.200.25 10.3.0.0 255.255.0.0 eq 2967 log disable
access-list inside_policy extended deny tcp host 10.200.200.25 10.2.0.0 255.255.0.0 eq 2967 log disable
access-list inside_policy extended deny tcp host 10.200.200.25 10.4.0.0 255.255.0.0 eq 2967 log disable
access-list inside_policy extended deny tcp host 10.200.200.25 10.5.0.0 255.255.0.0 eq 2967 log disable
access-list inside_policy extended deny udp object-group NO-LOG any eq 2967 log disable
access-list inside_policy extended deny tcp object-group NO-LOG any eq 2967 log disable
access-list inside_policy remark ====== Begin Outbound Mail Server Rules ======
access-list inside_policy extended permit udp host 10.200.200.222 any eq 5679
access-list inside_policy extended permit tcp host 10.200.200.222 any eq smtp
access-list inside_policy remark ****** End Outbound Mail Server Rules ******
access-list inside_policy extended permit ip object-group local_net_group any
access-list inside_policy extended permit icmp object-group local_net_group any
access-list OUTSIDECO_VPN extended permit ip host x.x.x.x object-group OUTSIDECO_SERVERS
access-list company-split-tunnel standard permit 10.1.0.0 255.255.0.0
access-list company-split-tunnel standard permit 10.2.0.0 255.255.0.0
access-list company-split-tunnel standard permit 10.3.0.0 255.255.0.0
access-list company-split-tunnel standard permit 10.4.0.0 255.255.0.0
access-list company-split-tunnel standard permit 10.200.0.0 255.255.0.0
access-list company-split-tunnel standard permit 10.5.0.0 255.255.0.0
access-list company-split-tunnel standard permit 10.6.0.0 255.255.0.0
access-list company-split-tunnel standard permit 10.7.0.0 255.255.0.0
access-list company-split-tunnel standard permit 172.22.22.0 255.255.255.0
access-list company-split-tunnel remark Video
access-list company-split-tunnel standard permit 192.168.0.0 255.255.0.0
access-list SSL_SPLIT standard permit 10.1.0.0 255.255.0.0
access-list SSL_SPLIT standard permit 10.2.0.0 255.255.0.0
access-list SSL_SPLIT standard permit 10.3.0.0 255.255.0.0
access-list SSL_SPLIT standard permit 10.200.0.0 255.255.0.0
access-list SSL_SPLIT standard permit 10.4.0.0 255.255.0.0
access-list SSL_SPLIT standard permit 10.5.0.0 255.255.0.0
access-list SSL_SPLIT standard permit 10.6.0.0 255.255.0.0
access-list SSL_SPLIT standard permit 10.7.0.0 255.255.0.0
access-list SSL_SPLIT standard permit 172.22.22.0 255.255.255.0
access-list SSL_SPLIT remark Video
access-list SSL_SPLIT standard permit 192.168.0.0 255.255.0.0
access-list NONAT_SSL extended permit ip object-group local_net_group 172.20.20.0 255.255.255.0
access-list NONAT_SSL extended permit ip 10.200.0.0 255.255.0.0 192.168.9.0 255.255.255.0
access-list tom extended permit tcp host x.x.x.x any eq smtp
access-list tom extended permit tcp host 10.200.200.222 any eq smtp
access-list tom extended permit tcp any host x.x.x.x
access-list aaron extended permit tcp any any eq 2967
access-list capauth extended permit ip host 10.200.200.1 host 10.200.200.220
access-list capauth extended permit ip host 10.200.200.220 host 10.200.200.1
access-list DMZ extended permit icmp any any
access-list dmz_access_in extended permit tcp any eq 51024 any eq 3336
access-list dmz_access_in extended permit icmp any any
access-list dmz_access_in extended permit tcp any any eq ftp
access-list dmz_access_in extended permit tcp any any eq https
access-list dmz_access_in remark rad5110 port 162 out
access-list dmz_access_in extended permit udp any any eq snmptrap
access-list dmz_access_in remark port 23 out
access-list dmz_access_in extended permit tcp any any eq telnet
access-list dmz_access_in remark port 53 dns out
access-list dmz_access_in extended permit object-group TCPUDP any any eq domain
access-list dmz_access_in extended permit object-group TCPUDP any any eq www
access-list dmz_access_in extended permit tcp any any eq h323
access-list dmz_access_in extended permit tcp any any object-group XML
access-list dmz_access_in extended permit udp any any object-group RAS
access-list dmz_access_in extended permit tcp any any range 1718 h323
access-list dmz_access_in extended permit tcp any any object-group H.245
access-list dmz_access_in extended permit object-group TCPUDP any any eq sip
access-list dmz_access_in extended permit udp any any object-group rtp_rtcp_udp
access-list dmz_access_in extended permit object-group TCPUDP any any object-group XML2
access-list dmz_access_in extended permit ip object-group local_net_group any
access-list dmz_access_in remark port 5061
access-list dmz_access_in extended permit tcp any any object-group tcp_tls
access-list outside_cryptomap extended permit ip 10.200.0.0 255.255.0.0 192.168.9.0 255.255.255.0
pager lines 24
logging enable
logging buffered warnings
logging trap informational
logging history informational
logging asdm warnings
logging host outside x.x.x.x
mtu outside 1500
mtu inside 1500
mtu dmz 1500
mtu Wireless 1500
mtu management 1500
ip local pool SSL_VPN_POOL 172.20.20.1-172.20.20.75 mask 255.255.255.0
ip verify reverse-path interface outside
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-631.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list NONAT_SSL
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) x.x.x.12 10.200.200.15 netmask 255.255.255.255
static (inside,outside) x.x.x.15 10.5.0.11 netmask 255.255.255.255
static (inside,outside) x.x.x.13 10.200.200.240 netmask 255.255.255.255
static (inside,outside) x.x.x.16 10.200.200.222 netmask 255.255.255.255
static (inside,outside) x.x.x.14 10.200.200.155 netmask 255.255.255.255
static (inside,dmz) 10.200.200.0 10.200.200.0 netmask 255.255.255.0
static (inside,dmz) 10.4.0.0 10.4.0.0 netmask 255.255.0.0
static (dmz,outside) x.x.x.18 172.22.22.15 netmask 255.255.255.255
static (dmz,outside) x.x.x.19 172.22.22.16 netmask 255.255.255.255
static (inside,dmz) 10.3.0.0 10.3.0.0 netmask 255.255.0.0
static (inside,dmz) 10.2.0.0 10.2.0.0 netmask 255.255.0.0
static (inside,dmz) 10.1.0.0 10.1.0.0 netmask 255.255.0.0
static (inside,dmz) 10.6.0.0 10.6.0.0 netmask 255.255.0.0
static (inside,dmz) 10.7.0.0 10.7.0.0 netmask 255.255.0.0
static (inside,dmz) 10.5.0.0 10.5.0.0 netmask 255.255.0.0
access-group outside_policy in interface outside
access-group inside_policy in interface inside
access-group dmz_access_in in interface dmz
route outside 0.0.0.0 0.0.0.0 x.x.x.12 1
route inside 10.1.0.0 255.255.0.0 10.200.200.254 1
route inside 10.2.0.0 255.255.0.0 10.200.200.254 1
route inside 10.3.0.0 255.255.0.0 10.200.200.254 1
route inside 10.4.0.0 255.255.0.0 10.200.200.254 1
route inside 10.5.0.0 255.255.0.0 10.200.200.254 1
route inside 10.6.0.0 255.255.0.0 10.200.200.254 1
route inside 10.7.0.0 255.255.0.0 10.200.200.150 1
route inside x.x.x.0 255.255.255.0 10.200.200.2 1
route inside x.x.x.0 255.255.255.0 10.200.200.2 1
route inside 192.168.1.0 255.255.255.0 10.200.200.254 1
route inside 192.168.2.0 255.255.255.0 10.200.200.254 1
route inside 192.168.3.0 255.255.255.0 10.200.200.254 1
route inside 192.168.4.0 255.255.255.0 10.200.200.254 1
route inside 192.168.5.0 255.255.255.0 10.200.200.254 1
route inside 192.168.6.0 255.255.255.0 10.200.200.254 1
route inside 192.168.7.0 255.255.255.0 10.200.200.254 1
route inside 192.168.200.0 255.255.255.0 10.200.200.254 1
route inside 192.168.201.0 255.255.255.0 10.200.200.254 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 2:00:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
aaa-server COMPANY-NT-AUTH protocol nt
aaa-server COMPANY-NT-AUTH (inside) host 10.200.200.220
nt-auth-domain-controller DC
aaa authentication ssh console LOCAL
aaa authorization command LOCAL
http server enable
http 10.200.200.0 255.255.255.0 inside
http 10.200.0.0 255.255.0.0 inside
http 10.3.0.0 255.255.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server community *****
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set AES256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set asa2transform esp-3des esp-sha-hmac
crypto ipsec transform-set 3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map outside_dyn_map 20 set transform-set 3DES-SHA
crypto dynamic-map outside_dyn_map 20 set security-association lifetime seconds 28800
crypto dynamic-map outside_dyn_map 20 set security-association lifetime kilobytes 4608000
crypto map OUTSIDE_MAP 5 match address outside_cryptomap
crypto map OUTSIDE_MAP 5 set pfs
crypto map OUTSIDE_MAP 5 set peer x.x.x.53
crypto map OUTSIDE_MAP 5 set transform-set 3DES-SHA
crypto map OUTSIDE_MAP 5 set security-association lifetime seconds 28800
crypto map OUTSIDE_MAP 10 match address OUTSIDECO_VPN
crypto map OUTSIDE_MAP 10 set peer x.x.x.25
crypto map OUTSIDE_MAP 10 set transform-set AES256-SHA
crypto map OUTSIDE_MAP 10 set security-association lifetime seconds 28800
crypto map OUTSIDE_MAP 10 set security-association lifetime kilobytes 4608000
crypto map OUTSIDE_MAP 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map OUTSIDE_MAP interface outside
crypto isakmp identity address
crypto isakmp enable outside
crypto isakmp policy 5
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 28800
crypto isakmp policy 10
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 outside
ssh 0.0.0.0 0.0.0.0 inside
ssh timeout 20
console timeout 0
dhcpd dns 10.200.200.220 10.200.200.225
dhcpd wins 10.200.200.220 10.200.200.225
dhcpd lease 18000
dhcpd domain company.com
dhcpd dns 10.200.200.220 10.200.200.225 interface Wireless
dhcpd wins 10.200.200.220 10.200.200.225 interface Wireless
dhcpd lease 18000 interface Wireless
dhcpd domain company.com interface Wireless
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ntp server 192.5.41.40 source outside prefer
ssl trust-point vpn.company.com outside
webvpn
enable outside
anyconnect-essentials
svc image disk0:/anyconnect-win-2.5.0217-k9.pkg 1
svc image disk0:/anyconnect-macosx-i386-2.5.2017-k9.pkg 2
svc enable
tunnel-group-list enable
group-policy SSL_Client_Policy internal
group-policy SSL_Client_Policy attributes
wins-server value 10.200.200.220
dns-server value 10.200.200.220
vpn-tunnel-protocol IPSec svc webvpn
split-tunnel-policy tunnelspecified
split-tunnel-network-list value SSL_SPLIT
default-domain value company.com
webvpn
sso-server none
auto-signon allow uri * auth-type all
group-policy no-split-test internal
group-policy no-split-test attributes
banner value Welcome to company and Associates
banner value Welcome to company and Associates
dns-server value 10.200.200.220
vpn-tunnel-protocol IPSec
ipsec-udp enable
split-tunnel-policy tunnelall
default-domain value company.com
group-policy DfltGrpPolicy attributes
dns-server value 10.200.200.220
default-domain value company.com
group-policy company internal
group-policy company attributes
banner value Welcome to company and Associates
banner value Welcome to company and Associates
dns-server value 10.200.200.220
vpn-tunnel-protocol IPSec
ipsec-udp enable
split-tunnel-policy tunnelspecified
split-tunnel-network-list value SSL_SPLIT
default-domain value company.com
username ciscoadmin password xxxxxxxxxxx encrypted privilege 15
tunnel-group DefaultWEBVPNGroup general-attributes
address-pool SSL_VPN_POOL
authentication-server-group COMPANY-NT-AUTH
default-group-policy SSL_Client_Policy
tunnel-group DefaultWEBVPNGroup webvpn-attributes
group-alias company_SSL_VPN enable
tunnel-group company_group type remote-access
tunnel-group company_group general-attributes
address-pool SSL_VPN_POOL
authentication-server-group COMPANY-NT-AUTH LOCAL
default-group-policy company
tunnel-group company_group ipsec-attributes
pre-shared-key *****
tunnel-group x.x.x.53 type ipsec-l2l
tunnel-group x.x.x.53 ipsec-attributes
pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map global_policy
class inspection_default
inspect tftp
inspect esmtp
inspect ftp
inspect icmp
inspect ip-options
inspect netbios
inspect rsh
inspect skinny
inspect sqlnet
inspect sunrpc
inspect xdmcp
inspect mgcp
inspect h323 h225
inspect h323 ras
inspect sip
service-policy global_policy global
privilege cmd level 5 mode exec command ping
privilege cmd level 6 mode exec command write
privilege show level 5 mode exec command running-config
privilege show level 5 mode exec command version
privilege show level 5 mode exec command conn
privilege show level 5 mode exec command memory
privilege show level 5 mode exec command cpu
privilege show level 5 mode exec command xlate
privilege show level 5 mode exec command traffic
privilege show level 5 mode exec command interface
privilege show level 5 mode exec command clock
privilege show level 5 mode exec command ip
privilege show level 5 mode exec command failover
privilege show level 5 mode exec command arp
privilege show level 5 mode exec command route
privilege show level 5 mode exec command blocks
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:a0689b4c837c79a51e7a0cfed591dec9
: end
COMPANY-asa#Hi Sian,
Yes on their end the PFS is enabled for DH Group 2.
Here is the information that you requested:
company-asa# sh crypto isakmp sa
Active SA: 3
Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 3
1 IKE Peer: x.x.x.87
Type : user Role : responder
Rekey : no State : AM_ACTIVE
2 IKE Peer: x.x.x.53
Type : L2L Role : initiator
Rekey : no State : MM_ACTIVE
3 IKE Peer: x.x.x.25
Type : user Role : initiator
Rekey : no State : MM_WAIT_MSG4
company-asa# sh crypto ipsec sa
interface: outside
Crypto map tag: OUTSIDE_MAP, seq num: 5, local addr: x.x.x.13
access-list outside_cryptomap extended permit ip 10.200.0.0 255.255.0.0 192.168.9.0 255.255.255.0
local ident (addr/mask/prot/port): (10.200.0.0/255.255.0.0/0/0)
remote ident (addr/mask/prot/port): (192.168.9.0/255.255.255.0/0/0)
current_peer: x.x.x.53
#pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
#pkts decaps: 10744, #pkts decrypt: 10744, #pkts verify: 10744
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 0, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
#send errors: 0, #recv errors: 0
local crypto endpt.: x.x.x.13, remote crypto endpt.: x.x.x.53
path mtu 1500, ipsec overhead 58, media mtu 1500
current outbound spi: 500EC8BF
current inbound spi : 8DAE3436
inbound esp sas:
spi: 0x8DAE3436 (2377004086)
transform: esp-3des esp-sha-hmac no compression
in use settings ={L2L, Tunnel, PFS Group 2, }
slot: 0, conn_id: 32768, crypto-map: OUTSIDE_MAP
sa timing: remaining key lifetime (kB/sec): (3914946/24388)
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0xFFFFFFFF 0xFFFFFFFF
outbound esp sas:
spi: 0x500EC8BF (1343146175)
transform: esp-3des esp-sha-hmac no compression
in use settings ={L2L, Tunnel, PFS Group 2, }
slot: 0, conn_id: 32768, crypto-map: OUTSIDE_MAP
sa timing: remaining key lifetime (kB/sec): (3915000/24388)
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000001
Crypto map tag: outside_dyn_map, seq num: 20, local addr: x.x.x.13
local ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0)
remote ident (addr/mask/prot/port): (172.20.20.8/255.255.255.255/0/0)
current_peer: x.x.x.87, username: ewebb
dynamic allocated peer ip: 172.20.20.8
#pkts encaps: 16434, #pkts encrypt: 16464, #pkts digest: 16464
#pkts decaps: 19889, #pkts decrypt: 19889, #pkts verify: 19889
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 16434, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 30, #pre-frag failures: 0, #fragments created: 60
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 60
#send errors: 0, #recv errors: 0
local crypto endpt.: x.x.x.13/4500, remote crypto endpt.: x.x.x.87/2252
path mtu 1500, ipsec overhead 66, media mtu 1500
current outbound spi: 2D712C9F
current inbound spi : 0EDB79C8
inbound esp sas:
spi: 0x0EDB79C8 (249264584)
transform: esp-3des esp-sha-hmac no compression
in use settings ={RA, Tunnel, NAT-T-Encaps, }
slot: 0, conn_id: 65536, crypto-map: outside_dyn_map
sa timing: remaining key lifetime (sec): 18262
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0xFFFFFFFF 0xFFFFFFFF
outbound esp sas:
spi: 0x2D712C9F (762391711)
transform: esp-3des esp-sha-hmac no compression
in use settings ={RA, Tunnel, NAT-T-Encaps, }
slot: 0, conn_id: 65536, crypto-map: outside_dyn_map
sa timing: remaining key lifetime (sec): 18261
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000001 -
Cisco ASA 5505 VPN Remote Acces Problem
Hello Guys .. i have cisco 5505 Asa security Adaptive , and i have two local networks 192.168.1.0 /24 and 192.168.2.0/24 , and i have my ISP public connection,,,,,what i want to do is i want to connect Remote VPN connection and access my Private Network of 192. my public ip is like 155.155.155.0 /24 ...
i put my ISP connection in the EO/0 and my private networks into E0/1 and E0/2.
so i created a remote vpn connection ,, and then i connected to the VPN ..
My problem i can't reach and access my private networks .. this probem frustrated me a lot .. so cisco guys please help me
and iam using ASDM cisco graphic interfaceHi Timothy,
Could you please try disabling UAC in Win 7. Also try to connect from a machine where you have admin privileges (in case you are trying connection from a restricted machine.
Also, add the site under trusted sites in IE. i.e if you are connecting to https://1.1.1.1 or https://vpn.abc.com then please add it under the trusted sites:
Let me know if this helps.
Thanks,
Vishnu Sharma -
Two Cisco ASA 5505, IPSec Multiple Subnets, Problem with Phase2, DSL
Hi all.
we have following IPSec configuration:
ASA Site 1:
Cisco Adaptive Security Appliance Software Version 9.1(1)
crypto ipsec ikev1 transform-set TSAES esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set TSMD5 esp-3des esp-md5-hmac
crypto ipsec ikev2 ipsec-proposal PropAES256
access-list SITE_2 extended permit ip 172.27.0.0 255.255.0.0 172.27.97.0 255.255.255.0
access-list SITE_2 extended permit ip 172.28.60.0 255.255.254.0 172.27.97.0 255.255.255.0
access-list SITE_2 extended permit ip 172.22.0.0 255.255.0.0 172.27.97.0 255.255.255.0
access-list SITE_2 extended permit ip 172.27.0.0 255.255.0.0 172.27.99.0 255.255.255.0
access-list SITE_2 extended permit ip 172.22.0.0 255.255.0.0 172.27.99.0 255.255.255.0
crypto map CMVPN 5 match address SITE_2
crypto map CMVPN 5 set peer IP_SITE2
crypto map CMVPN 5 set ikev2 ipsec-proposal PropAES256
crypto map CMVPN interface OUTSIDE
route OUTSIDE 172.27.97.0 255.255.255.0 citic-internet-gw 255
route OUTSIDE 172.27.99.0 255.255.255.0 citic-internet-gw 255
tunnel-group IP_SITE2 type ipsec-l2l
tunnel-group IP_SITE2 general-attributes
default-group-policy VPN_S2S_WAN
tunnel-group IP_SITE2 ipsec-attributes
ikev2 remote-authentication pre-shared-key *****
ikev2 local-authentication pre-shared-key *****
ASA Site 2:
Cisco Adaptive Security Appliance Software Version 9.1(4)
access-list SITE_1 extended permit ip 172.27.97.0 255.255.255.0 172.28.60.0 255.255.254.0
access-list SITE_1 extended permit ip 172.27.97.0 255.255.255.0 172.27.0.0 255.255.0.0
access-list SITE_1 extended permit ip 172.27.97.0 255.255.255.0 172.22.0.0 255.255.0.0
access-list SITE_1 extended permit ip 172.27.99.0 255.255.255.0 172.27.0.0 255.255.0.0
access-list SITE_1 extended permit ip 172.27.99.0 255.255.255.0 172.22.0.0 255.255.0.0
crypto map CMVPN 10 match address SITE_1
crypto map CMVPN 10 match address SITE_1
crypto map CMVPN 10 set peer IP_SITE1
crypto map CMVPN 10 set ikev2 ipsec-proposal IKEV2AES
crypto map CMVPN 10 set reverse-route
crypto map CMVPN interface OUTSIDE
tunnel-group IP_SITE1 type ipsec-l2l
tunnel-group IP_SITE1 general-attributes
default-group-policy VPN_S2S_WAN
tunnel-group IP_SITE1 ipsec-attributes
ikev2 remote-authentication pre-shared-key *****
ikev2 local-authentication pre-shared-key *****
We are not able to reach from 172.22.20.x ips 172.27.99.x.
It seems so that the phase2 for this subnet is missing…...... as long as we try to reach from 172.27.99.x any ip in 172.22.20.x.
We are using similar configuration on many sites and it works correctly expect sites with DSL line.
We can exclude problem with NAT,ACL or routing. The connection is working fine as long as “we open all phase 2 manually” . After re-open (idle timeout) the tunnel the problem comes back.
Thanks in advance for your help.
Regards.
Jan
ASA Site 1# sh vpn-sessiondb detail l2l filter ipaddress ASA Site 2
Session Type: LAN-to-LAN Detailed
Connection : IP ASA Site 2
Index : 3058 IP Addr : IP ASA Site 2
Protocol : IKEv2 IPsec
Encryption : IKEv2: (1)AES256 IPsec: (3)AES256
Hashing : IKEv2: (1)SHA512 IPsec: (3)SHA1
Bytes Tx : 423634 Bytes Rx : 450526
Login Time : 19:59:35 HKT Tue Apr 29 2014
Duration : 1h:50m:45s
IKEv2 Tunnels: 1
IPsec Tunnels: 3
IKEv2:
Tunnel ID : 3058.1
UDP Src Port : 500 UDP Dst Port : 500
Rem Auth Mode: preSharedKeys
Loc Auth Mode: preSharedKeys
Encryption : AES256 Hashing : SHA512
Rekey Int (T): 86400 Seconds Rekey Left(T): 79756 Seconds
PRF : SHA512 D/H Group : 5
Filter Name :
IPv6 Filter :
IPsec:
Tunnel ID : 3058.2
Local Addr : 172.22.0.0/255.255.0.0/0/0
Remote Addr : 172.27.97.0/255.255.255.0/0/0
Encryption : AES256 Hashing : SHA1
Encapsulation: Tunnel
Rekey Int (T): 28800 Seconds Rekey Left(T): 22156 Seconds
Rekey Int (D): 4608000 K-Bytes Rekey Left(D): 4607648 K-Bytes
Idle Time Out: 25 Minutes Idle TO Left : 24 Minutes
Bytes Tx : 312546 Bytes Rx : 361444
Pkts Tx : 3745 Pkts Rx : 3785
IPsec:
Tunnel ID : 3058.3
Local Addr : 172.27.0.0/255.255.0.0/0/0
Remote Addr : 172.27.97.0/255.255.255.0/0/0
Encryption : AES256 Hashing : SHA1
Encapsulation: Tunnel
Rekey Int (T): 28800 Seconds Rekey Left(T): 22165 Seconds
Rekey Int (D): 4608000 K-Bytes Rekey Left(D): 4607952 K-Bytes
Idle Time Out: 25 Minutes Idle TO Left : 24 Minutes
Bytes Tx : 50014 Bytes Rx : 44621
Pkts Tx : 496 Pkts Rx : 503
IPsec:
Tunnel ID : 3058.4
Local Addr : 172.27.0.0/255.255.0.0/0/0
Remote Addr : 172.27.99.0/255.255.255.0/0/0
Encryption : AES256 Hashing : SHA1
Encapsulation: Tunnel
Rekey Int (T): 28800 Seconds Rekey Left(T): 22324 Seconds
Rekey Int (D): 4608000 K-Bytes Rekey Left(D): 4607941 K-Bytes
Idle Time Out: 25 Minutes Idle TO Left : 24 Minutes
Bytes Tx : 61074 Bytes Rx : 44461
Pkts Tx : 402 Pkts Rx : 437
NAC:
Reval Int (T): 0 Seconds Reval Left(T): 0 Seconds
SQ Int (T) : 0 Seconds EoU Age(T) : 6648 Seconds
Hold Left (T): 0 Seconds Posture Token:
Redirect URL :
.... after ping from 172.27.99.x any ip in 172.22.20.x.
ASA Site 1# sh vpn-sessiondb detail l2l filter ipaddress ASA Site 2
Session Type: LAN-to-LAN Detailed
Connection : IP ASA Site 2
Index : 3058 IP Addr : IP ASA Site 2
Protocol : IKEv2 IPsec
Encryption : IKEv2: (1)AES256 IPsec: (4)AES256
Hashing : IKEv2: (1)SHA512 IPsec: (4)SHA1
Bytes Tx : 784455 Bytes Rx : 1808965
Login Time : 19:59:35 HKT Tue Apr 29 2014
Duration : 2h:10m:48s
IKEv2 Tunnels: 1
IPsec Tunnels: 4
IKEv2:
Tunnel ID : 3058.1
UDP Src Port : 500 UDP Dst Port : 500
Rem Auth Mode: preSharedKeys
Loc Auth Mode: preSharedKeys
Encryption : AES256 Hashing : SHA512
Rekey Int (T): 86400 Seconds Rekey Left(T): 78553 Seconds
PRF : SHA512 D/H Group : 5
Filter Name :
IPv6 Filter :
IPsec:
Tunnel ID : 3058.2
Local Addr : 172.22.0.0/255.255.0.0/0/0
Remote Addr : 172.27.97.0/255.255.255.0/0/0
Encryption : AES256 Hashing : SHA1
Encapsulation: Tunnel
Rekey Int (T): 28800 Seconds Rekey Left(T): 20953 Seconds
Rekey Int (D): 4608000 K-Bytes Rekey Left(D): 4606335 K-Bytes
Idle Time Out: 25 Minutes Idle TO Left : 24 Minutes
Bytes Tx : 652492 Bytes Rx : 1705136
Pkts Tx : 7419 Pkts Rx : 7611
IPsec:
Tunnel ID : 3058.3
Local Addr : 172.27.0.0/255.255.0.0/0/0
Remote Addr : 172.27.97.0/255.255.255.0/0/0
Encryption : AES256 Hashing : SHA1
Encapsulation: Tunnel
Rekey Int (T): 28800 Seconds Rekey Left(T): 20962 Seconds
Rekey Int (D): 4608000 K-Bytes Rekey Left(D): 4607942 K-Bytes
Idle Time Out: 25 Minutes Idle TO Left : 24 Minutes
Bytes Tx : 60128 Bytes Rx : 52359
Pkts Tx : 587 Pkts Rx : 594
IPsec:
Tunnel ID : 3058.4
Local Addr : 172.27.0.0/255.255.0.0/0/0
Remote Addr : 172.27.99.0/255.255.255.0/0/0
Encryption : AES256 Hashing : SHA1
Encapsulation: Tunnel
Rekey Int (T): 28800 Seconds Rekey Left(T): 21121 Seconds
Rekey Int (D): 4608000 K-Bytes Rekey Left(D): 4607931 K-Bytes
Idle Time Out: 25 Minutes Idle TO Left : 24 Minutes
Bytes Tx : 70949 Bytes Rx : 50684
Pkts Tx : 475 Pkts Rx : 514
IPsec:
Tunnel ID : 3058.5
Local Addr : 172.22.0.0/255.255.0.0/0/0
Remote Addr : 172.27.99.0/255.255.255.0/0/0
Encryption : AES256 Hashing : SHA1
Encapsulation: Tunnel
Rekey Int (T): 28800 Seconds Rekey Left(T): 28767 Seconds
Rekey Int (D): 4608000 K-Bytes Rekey Left(D): 4608000 K-Bytes
Idle Time Out: 25 Minutes Idle TO Left : 24 Minutes
Bytes Tx : 961 Bytes Rx : 871
Pkts Tx : 17 Pkts Rx : 14
NAC:
Reval Int (T): 0 Seconds Reval Left(T): 0 Seconds
SQ Int (T) : 0 Seconds EoU Age(T) : 7852 Seconds
Hold Left (T): 0 Seconds Posture Token:
Redirect URL :Hi,
on 212 is see
tunnel-group 195.xxx.xxx.xxx type ipsec-l2l
tunnel-group 195.xxx.xxx.xxx ipsec-attributes
pre-shared-key
When you define the peer with static tunnel-group entry ASA is looking for peer configuration in static crypto map. If the peer is behind static NAT configure a proper static crypto map with matching acl and proposals.
If the peer is behind dynamic nat refer this example :http://www.cisco.com/c/en/us/support/docs/security/pix-500-series-security-appliances/81883-ipsec-iosrtr-dyn-pix-nat.html
Regards,
Abaji. -
I am running version asa922.8-k8.I have tried via CLI to setup my rules and my access rules are not showing up in ASDM. Here are the rules that I had entered;
firewall>enable
firewall#configure terminal
firewall(config)#object network xbox
firewall(config-network-object)#host 192.168.1.100
firewall(config-network-object)#exit
firewall(config)#
firewall(config)#object network xbox-nat-tcp3074
firewall(config-network-object)#host 192.168.1.100
firewall(config-network-object)#exit
firewall(config)#object network xbox-nat-udp3074
firewall(config-network-object)#host 192.168.1.100
firewall(config-network-object)#exit
firewall(config)#object network xbox-nat-udp88
firewall(config-network-object)#host 192.168.1.100
firewall(config-network-object)#exit
firewall(config)#
firewall(config)#object network xbox-nat-tcp3074
firewall(config-network-object)#host 192.168.1.100
firewall(config-network-object)#exit
firewall(config)#object network xbox-nat-udp3074
firewall(config-network-object)#host 192.168.1.100
firewall(config-network-object)#exit
firewall(config)#object network xbox-nat-udp88
firewall(config-network-object)#host 192.168.1.100
firewall(config-network-object)#exit
firewall(config)#
firewall(config)#object-group service xbox-live-3074 tcp-udp
firewall(config-service-object-group)#port-object eq 3074
firewall(config-service-object-group)#exit
firewall(config)#object service xbox-live-88
firewall(config-service-object)#service udp destination eq 88
firewall(config-service-object)#exit
firewall(config)#
firewall(config)#object network xbox-nat-tcp3074
firewall(config-network-object)#nat (inside,outside) static interface service tcp 3074 3074
firewall(config-network-object)#exit
firewall(config)#object network xbox-nat-udp3074
firewall(config-network-object)#nat (inside,outside) static interface service udp 3074 3074
firewall(config-network-object)#exit
firewall(config)#object network xbox-nat-udp88
firewall(config-network-object)#nat (inside,outside) static interface service udp 88 88
firewall(config-network-object)#exit
firewall(config)#
firewall(config)#access-list outside_access_in line 1 extended permit tcp any object xbox object-group xbox-live-3074
firewall(config)#access-list outside_access_in line 2 extended permit udp any object xbox object-group xbox-live-3074
firewall(config)#access-list outside_access_in line 3 extended permit object xbox-live-88 any object xbox
how do i do the access list via ASDM? Running the latest version of asdm.The question is: What doesn't show up?
If you only configured the lines above, then the ACL is not yet applied to an interface. It won't show up under "Access-Control", but it should show up under "ACL Manager". Same for the objects. They also should be visible in ASDM.
If thats the case, then just apply the ACL to the interface:
access-list outside_access_in in interface outside
Maybe you are looking for
-
How do I tell what the latest software versions is...
Hi There, I have a Nokia Sapphire Arte and was wondering what the latest rev of code is available for it? I am awaiting a new USB cable in the mail, so, I can't hook it up to Nokia Updater right now to determine this. Thanks! Lumia 920/N9 Previous Li
-
How to represent XML inline tags in a Java class
Dear all, I am currently dealing with the issue of how to transform an XML document into a Java representation. As far as the strucural elements are concerned, I'd represent them each one of them as a Java class. However, the XML structure also allow
-
Which airport card to install on g4 imac (17")
i just bought a new imac and want to put my g4 imac in another room. i'd like to install an airport card so i can access the internet through the time machine (which is connected to the new imac). i'm having trouble figuring out which card to get--ai
-
Acrobat 8 hangs when selecting "Help" menu...
I'm running the latest (all updates as of today) version of Acrobat Pro and the latest version of OS X 10.5.4 on a Mac Pro. Whenever I move my mouse of the Help menu, Acrobat stall I first get the old wristwatch, then the beachball spins. It takes b
-
Is it possible to make a cartoon animation video with Premiere Elements ?
Is it possible to insert 16 different images every seconds in a video ? I will like to make an cartoon animation. Is it possible with Premiere Elements ? It look like it is only possible to change a picture/image every 1 seconds. What software is goo