CISCO ASA WITH FORTIMAIL

Hi
Recently we want to replace the CSC for a Fortimail, my quetion is how I redirect the smtp trafic to the Fortimail Appliance from the ASA because the ASA received the traffic SMTP.

You don't redirect the traffic from the ASA to the Fortimail. That's (to my knowledge) not a possible design. You have probably two ways to deploy the Fortimail in your environment:
Gateway mode
For that you configure your internal mail-server with the Fortimail as a smarthost. On the ASA you change the port-forwarding which is configured to your internal Mailserver to the Fortigate.
Transparent mode
Here you place the FortiMail inline between your Mail-Server and the ASA.
For the rest it is probably better to ask in a Fortinet-support-forum.

Similar Messages

PortChannel in Cisco ASA with subinterface vlan

Dear Cisco Expert,
I have problem with portchannel in cisco ASA with subinterface, My asa create port channel two link with switch :
my asa configuration (PO3 == int gi0/1 & int gi0/0 ASA) :
interface Port-channel3
no nameif
no security-level
no ip address
interface Port-channel3.20
vlan 20
nameif XXXX
security-level 50
ip address 172.27.3.1 255.255.255.224
my switch configuration (PO3 == int gi0/19 & int gi0/20 switch) :
interface Port-channel3
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 20,30,40,50
switchport mode trunk
end
I also tried create int vlan 20 in switch,
interface Vlan20
ip address 172.27.3.2 255.255.255.224
end
but it doesn't work
the etherchannel status is still in waiting :
show etherchannel sum :
3 Po3(SD) LACP Gi0/19(w) Gi0/20(w)
Do you have any clue ?
Thank u guys, ...
Btw, if i create ASA port chanel withoout subinterface it's work.
Best Regards
Rizal Ferdiyan

You ASA cofniguration should look like this. You havnt posted the full config so no comment on that
interface GigabitEthernet0/0
channel-group 10 mode active
speed 1000
duplex full
no nameif
no security-level
no ip address
interface GigabitEthernet0/1
channel-group 10 mode active
speed 1000
duplex full
no nameif
no security-level
no ip address
interface Port-channel3
speed 1000
duplex full
no nameif
no security-level
no ip address
interface Port-channel3.20
vlan 20
nameif XXXX
security-level 50
ip address 172.27.3.1 255.255.255.224
Thanks
Ajay

Error Routing protocol - EIGRP between Cisco ASA with Switch 4506

Dear Cisco Team,
I have problem when I configed EIGRP between cisco ASA 5510 with core switch 4506. This is below error
*Nov 4 05:08:09.898: %DUAL-5-NBRCHANGE: EIGRP-IPv4 100: Neighbor 172.16.10.20 (GigabitEthernet2/42) is up: new adjacency
*Nov 4 05:09:29.409: %DUAL-5-NBRCHANGE: EIGRP-IPv4 100: Neighbor 172.16.10.20 (GigabitEthernet2/42) is down: retry limit exceeded
*Nov 4 05:09:29.499: %DUAL-5-NBRCHANGE: EIGRP-IPv4 100: Neighbor 172.16.10.20 (GigabitEthernet2/42) is up: new adjacency
*Nov 4 05:10:35.609: %DUAL-5-NBRCHANGE: EIGRP-IPv4 100: Neighbor 172.16.10.18 (GigabitEthernet2/42) is down: holding time expired
*Nov 4 05:10:49.009: %DUAL-5-NBRCHANGE: EIGRP-IPv4 100: Neighbor 172.16.10.20 (GigabitEthernet2/42) is down: retry limit exceeded
*Nov 4 05:10:53.230: %DUAL-5-NBRCHANGE: EIGRP-IPv4 100: Neighbor 172.16.10.20 (GigabitEthernet2/42) is up: new adjacency
quang huy2004: *Nov 4 05:08:09.898: %DUAL-5-NBRCHANGE: EIGRP-IPv4 100: Neighbor 172.16.10.20 (GigabitEthernet2/42) is up: new adjacency
*Nov 4 05:09:29.409: %DUAL-5-NBRCHANGE: EIGRP-IPv4 100: Neighbor 172.16.10.20 (GigabitEthernet2/42) is down: retry limit exceeded
*Nov 4 05:09:29.499: %DUAL-5-NBRCHANGE: EIGRP-IPv4 100: Neighbor 172.16.10.20 (GigabitEthernet2/42) is up: new adjacency
*Nov 4 05:10:35.609: %DUAL-5-NBRCHANGE: EIGRP-IPv4 100: Neighbor 172.16.10.18 (GigabitEthernet2/42) is down: holding time expired
*Nov 4 05:10:49.009: %DUAL-5-NBRCHANGE: EIGRP-IPv4 100: Neighbor 172.16.10.20 (GigabitEthernet2/42) is down: retry limit exceeded
*Nov 4 05:10:53.230: %DUAL-5-NBRCHANGE: EIGRP-IPv4 100: Neighbor 172.16.10.20 (GigabitEthernet2/42) is up: new adjacency
the tech Spec
ASA, IOS : 8.0.2
4506, License IP Base; OS: Unisal 15 M.2
I checked between ASA with Router ok; but between ASA with 4506 error
Can you help me ?

Hello,
This logs means that the hold time expired so the hello packets are not being received, usually means multicast packets are missed-224.0.0.10)
I would recommend you to try another cable because this ussualy is a phisical or congestion issue.
Can you try that and let us know the result, also if that does not help can you send us the following outputs:
-Show ip EIGPR neighbors
-Debug EIGRP packet hello
Regards,
Julio

Cisco ASA with IMAP4S proxy

Hi,
we want to access our mail server (Lotus Domino) with an iPhone through a Cisco ASA configured as a IMAP-SSL proxy.
I have no problem accessing the server with Apple Mail, but not with the iPhone!
After the successful SSL handshake and AAA authetification the SSL connection is terminated with "client channel close"
Any ideas?

hello Vinish
recommending you to place this question to Security -> Firewalling forum instead of Small Business Security. Cisco ASA devices are not part of Small Business portfolio and ASA knowledgeable users are probably not checking this Small Business. That's reason why nobody responded yet probably.

Need help - Cisco ASA with FirePOWER

hi
currently we are using asa 5510 without firepower feature. our aim is to publish web servers and microsoft lync with reverse proxy method. control internet traffic , apply particular extensions file not to download , bandwidth management etc.
Is it possible when we add firepower on asa 5510 ..... please guide me.... thanks

Thanks for your detailed reply brother. actually we have deployed lync server 2013 with reverse proxy so it is must. see the comparison . i should go with Sophos UTM Firewall what you advice me...
Feature
Cisco Firepower
Fortinet
Sophos Utm
Firewall
✓
✓
✓
IPS
✓
✓
✓
Antivirus Gateway
✓
✓
AntiMalware*
✓
✓
Antispam
✓
✓
HTTP Proxy
✓
✓
Reverse Proxy
Partially
✓
✓
Web Filtering
✓
✓
✓
Email Protection
✓
✓
Wireless Controller
✓
Bandwidth Control
Expected in Next Year
Limited
✓
Application Visibility and control
✓
✓
✓
Data Loss Prevention
✓
✓
Advance Threat Prevention
✓
✓
✓
On BOX reporting
Limited
✓
External Reporting
✓
✓
✓
Web Reputation defence
✓
✓
✓
Failover
✓
✓
✓

Integrating Microsoft NAP with Cisco ASA

Hello everyone,
I'm quite new to the Cisco world. I wonder if and how it is possible to marry Cisco ASA with Microsoft NAP (in Terms of VPN Enforcement). Does anybody know some helpful documents? Is an ACS Server/Appliance necessary?
Thanks in advance and kind regards

Hello Jatin,
thanks for your reply.
Microsoft states that authentication via PEAP is necessary for NAP to work:
"One security feature of PEAP is the transmission of Statement of Health (SoH) messages."
(see http://blogs.msdn.com/b/openspecification/archive/2009/06/05/peap-phase-2-encapsulation-examples-for-a-client-authenticating-with-ms-chapv2.aspx?Redirected=true)
However, I found this topic which states that PEAP auth. is not possible with the ASA: https://supportforums.cisco.com/thread/2028742
Is that true?

Not Able to Telnet or SSH Cisco ASA

Hi,
I am not able to do the following to Cisco ASA with one IP address 172.19.1.11, below is the configuration in ASA. Earlier it was working, all of a sudden it stopped working.
Please help.
1. Not Able to SSH
2. Solarwinds not able to take information from ASA.
http 172.19.1.11 255.255.255.255 inside
snmp-server host inside 172.19.1.11 community srnemapd
telnet 172.19.1.11 255.255.255.255 inside
ssh 172.19.1.11 255.255.255.255 inside
ntp server 172.19.1.11 source inside prefer

Hi there,
Just add a new IP address for ssh to ASA, this will kick start the demon.
This new IP does not have to be a real one.
Hope this helps.
Thanks
Rizwan Rafeek

Setting up site to site vpn with cisco asa 5505

I have a cisco asa 5505 that needs to be set up for site to site vpn to a cisco asa 5500. The 5505 is the remote office and the 5500 is the main office.
IP of remote office router is 71.37.178.142
IP of the main office firewall is 209.117.141.82
Can someone tell me if my config is correct, this is the first time I am setting this up and it can not be tested until I set it up at the remote office. I would rather know its correct before I go.
ciscoasa# show run
: Saved
ASA Version 7.2(4)
hostname ciscoasa
domain-name default.domain.invalid
enable password TMACBloMlcBsq1kp encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
dns server-group DefaultDNS
domain-name default.domain.invalid
access-list outside_1_cryptomap extended permit ip host 71.37.178.142 host 209.117.141.82
access-list inside_nat0_outbound extended permit ip 192.168.1.0 255.255.255.0 host 209.117.141.82
access-list inside_nat0_outbound extended permit ip host 71.37.178.142 host 209.117.141.82
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-524.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs group5
crypto map outside_map 1 set peer 209.117.141.82
crypto map outside_map 1 set transform-set ESP-AES-256-SHA
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption aes-256
hash sha
group 5
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
vpdn username [email protected] password ********* store-local
dhcpd auto_config outside
dhcpd address 192.168.1.2-192.168.1.129 inside
dhcpd enable inside
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
service-policy global_policy global
prompt hostname context
Cryptochecksum:7e338fb2bf32a9ceb89560b314a5ef6c
: end
ciscoasa#
Thanks!

Hi Mandy,
By using following access list define Peer IP as source and destination
access-list outside_1_cryptomap extended permit ip host 71.37.178.142 host 209.117.141.82
you are not defining the interesting traffic / subnets from both ends.
Make some number ACL 101 as you do not have to write the extended keyword then if you like as follows, or else NAME aCL will also work:
access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
access-list 101 remark CCP_ACL Category=4 access-list 101 remark IPSEC Rule
!.1..source subnet(called local encryption domain) at your end 192.168.200.0
!..2.and destination subnet(called remote encryption domain)at other end 192.168.100.0 !.3..I mean you have to define what subnets you need to communicate between which are behind these firewalls
!..4...Local Subnets behind IP of the main office firewall is 209.117.141.82 say
!...at your end 192.168.200.0
!..5.Remote Subnets behind IP of remote office router is 71.37.178.142 say
!...at other end 192.168.100.0
Please use Baisc Steps as follows:
A. Configuration in your MAIN office having IP = 209.117.141.82 (follow step 1 to 6)
Step 1.
Define Crypto ACL/ mirror ACL for other end (change source to destination and destination to source in other side router or VPN device and thats why they are called mirror ACL/ or also called Proxy ID or also called Proxy ACL, your interesting traffic , that you want to encrypt / trave/enter in the tunnel)
access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
Step 2.
Config ISAKMP Policy with minimum 4 parameters are to be config for
crypto isakmp policy 10
authentication pre-share ---> Ist parameter of setting Authentication type ISAKMP Policy is OK
encryption aes-256   --->2nd parameter of ISAKMP Policy is OK
hash sha   ---> 3rd parameter of ISAKMP Policy is OK
group 5 ---> 4th parameter of ISAKMP Policy is OK
lifetime 86400 ------ > this 5th parameter is optional , and will negotiate for the less value at either end or by default is will be taken 86400
Step 3.
Define Preshared key or PKI which you will use with other side Peer address 71.37.178.142, either key type 0 is Plain text anyone can see it over internet, or use key type 6 for encrypted key , say your password is CISCO123
Here in your case in step 2 Authentication is using PSK, looks you have not defines Password
Use following command:
crypto isakmp key 0 CISCO123 address 71.37.178.142
or , but not both
crypto isakmp key 6 CISCO123 address71.37.178.142
step 4.
Define Transform set , which will be used for phase 2 tunnel parameters, if you use ESP it can have to sets one cor encryption and other for Authentication.
Here is yours one:
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
this is correct but give name somthing easier to remember /distinguish it is a transform set , like TSET1 instead of ESP-AES-256-SHA ,try following (here you are using ESP so for encryption we use first set as esp-des and for authentication we use second set esp-sha-hmac)
crypto ipsec transform-set TSET1 esp-des esp-sha-hmac
or
crypto ipsec transform-set TSET1 esp-aes-256 esp-sha-hmac
Suppose you are using only AH then as AH does not support encryption or confidentiality hence it always use onle one set not 2 sets like ESP(remember the difference) say for example only one set for auth etc but no set for encryption hence AH have no such sets like ah-des or ah-3des or ah-aes, it has only second set for authentication like
ah-sha-hmac or ah-md5-hmac
crypto ipsec transform-set TSET1 ah-sha-hmac
or
crypto ipsec transform-set TSET1 ah-md5-hmac
Step 5.
Now configure Crypto MAP as follows and only one CMPA can be applied to OUTSIDE Interface as VPN tunnel is alsways applied for traffic from inside subnets to outside subnets and only once Cryptomap can be applied to OUTSIDE Interface and hence for several VPN peers from different vendors we use seq no 10, 2 30 for different tunnels in one single CMAP:
crypto map ipsec-isakmp
1. Define peer -- called WHO to set tunnel with
2. Define or call WHICH - Transform Set
3. Define WHAT to call interesting traffic define in your ACL or Proxy ID or Proxy ACL in step 1 using match address
Like in your case it is but ipsec-isakmp keyword missing in the ;ast
crypto map outside_map 10 ipsec-isakmp
1. set peer 209.117.141.82 -----> is correct as this is your other side peer called WHO in my step
2. set transform-set TSET1 -----> is correct as this is WHICH, and only one transform set can be called
!..In you case it is correct
!...set transform-set ESP-AES-256-SHA (also correct)
3. match address outside_1_cryptomap ---->Name of the extended ACL define as WHAT to pass through this tunnel
4. set pfs group5 (this is optional but if config at one end same has to be config at other side peer as well)
Step 6.
Now apply this one crypto MAP to your OUTSIDE interface always
interface outside
crypto map outside_map
Configure the same but just change ACL on other end in step one by reversing source and destination
and also set the peer IP of this router in other end.
So other side config should look as follows:
B. Configuration in oyur Remote PEER IP having IP = 71.37.178.142 (follow step 7 to 12)
Step 7.
Define Crypto ACL/ mirror ACL for other end (change source to destination and destination to source in other side router or VPN device and thats why they are called mirror ACL/ or also called Proxy ID or also called Proxy ACL, your interesting traffic , that you want to encrypt / trave/enter in the tunnel)
access-list outside_1_cryptomap extended ip 192.168.100.0 0.0.0.255 192.168.200.0 0.0.0.255
Step 8.
Config ISAKMP Policy with minimum 4 parameters are to be config for
crypto isakmp policy 10
authentication pre-share ---> Ist parameter of setting Authentication type ISAKMP Policy is OK
encryption aes-256   --->2nd parameter of ISAKMP Policy is OK
hash sha   ---> 3rd parameter of ISAKMP Policy is OK
group 5 ---> 4th parameter of ISAKMP Policy is OK
lifetime 86400 ------ > this 5th parameter is optional , and will negotiate for the less value at either end or by default is will be taken 86400
Step 9.
Define Preshared key or PKI which you will use with other side Peer address key type 0 is Plain text anyone can see it over internet, or use key type 6 for encrypted key , say your password is CISCO123
Here in your case in step 8 Authentication is using PSK, looks you have not defines Password
Use following command:
crypto isakmp key 0 CISCO123 address 209.117.141.82
or , but not both
crypto isakmp key 6 CISCO123 address 209.117.141.82
step 10.
Define Transform set , which will be used for phase 2 tunnel parameters, if you use ESP it can have to sets one cor encryption and other for Authentication.
Here is yours one:
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
this is correct but give name somthing easier to remember /distinguish it is a transform set , like TSET1 instead of ESP-AES-256-SHA ,try following (here you are using ESP so for encryption we use first set as esp-des and for authentication we use second set esp-sha-hmac)
crypto ipsec transform-set TSET1 esp-des esp-sha-hmac
or
crypto ipsec transform-set TSET1 esp-aes-256 esp-sha-hmac
Suppose you are using only AH then as AH does not support encryption or confidentiality hence it always use onle one set not 2 sets like ESP(remember the difference) say for example only one set for auth etc but no set for encryption hence AH have no such sets like ah-des or ah-3des or ah-aes, it has only second set for authentication like
ah-sha-hmac or ah-md5-hmac
crypto ipsec transform-set TSET1 ah-sha-hmac
or
crypto ipsec transform-set TSET1 ah-md5-hmac
Step 11.
Now configure Crypto MAP as follows and only one CMPA can be applied to OUTSIDE Interface as VPN tunnel is alsways applied for traffic from inside subnets to outside subnets and only once Cryptomap can be applied to OUTSIDE Interface and hence for several VPN peers from different vendors we use seq no 10, 2 30 for different tunnels in one single CMAP:
crypto map    ipsec-isakmp
1. Define peer -- called WHO to set tunnel with
2. Define or call WHICH - Transform Set, only one is permissible
3. Define WHAT to call interesting traffic define in your ACL or Proxy ID or Proxy ACL in step 1 using match address
Like in your case it is but ipsec-isakmp keyword missing in the ;ast
crypto map outside_map 10 ipsec-isakmp
1. set peer 209.117.141.82 -----> is correct as this is your other side peer called WHO in my step
2. set transform-set TSET1 -----> is correct as this is WHICH, and only one transform set can be called
!..In you case it is correct
!...set transform-set ESP-AES-256-SHA (also correct)
3. match address outside_1_cryptomap ---->Name of the extended ACL define as WHAT to pass through this tunnel
4. set pfs group5 (this is optional but if config at one end same has to be config at other side peer as well)
Step 12.
Now apply this one crypto MAP to your OUTSIDE interface always
interface outside
crypto map outside_map
Now initite a ping
Here is for your summary:
IPSec: Site to Site - Routers
Configuration Steps
Phase 1
Step 1: Configure Mirrored ACL/Crypto ACL       for Interesting Traffic
Step 2: Configure ISAKMP Policy
Step 3: Configure ISAKMP Key
Phase 2
Step 4: Configure Transform Set
Step 5: Configure Crypto Map
Step 6: Apply Crypto Map to an Interface
To debug for Phase 1 and Phase 2. Store it in buffer without displaying logs on terminal.
Router#debug crpyto isakmp
Router#debug crpyto ipsec
Router(config)# logging buffer 7
Router(config)# logging buffer 99999
Router(config)# logging console 6
Router# clear logging
Configuration
In R1:
(config)# access-list 101 permit ipo host 10.1.1.1 host      10.1.2.1
(config)# crypto isakmp policy 10
(config-policy)# encryption 3des
(config-policy)# authentication pre-share
(config-policy)# group 2
(config-policy)# hash sha1
(config)# crypto isakmp key 0 cisco address 2.2.2.1
(config)# crypto ipsec transform-set TSET esp-3des      sha-aes-hmac
(config)# crypto map CMAP 10 ipsec-isakmp
(config-crypto-map)# set peer 2.2.2.1
(config-crypto-map)# match address 101
(config-crypto-map)# set transform-set TSET
(config)# int f0/0
(config-if)# crypto map CMAP
Similarly in R2
Verification Commands
#show crypto isakmp SA
#show crypto ipsec SA
Change to Transport Mode, add the following command in Step 4:
(config-tranform-set)# mode transport
Even after doing this change, the ipsec negotiation will still be done through tunnel mode if pinged from Loopback to Loopback. To overcome this we make changes to ACL.
Change to Aggressive Mode, replace the Step 3 command with these commands in R1:
(config)# crypto isakmp peer address 2.2.2.1
(config-peer)# set aggressive-mode password cisco
(config-peer)# set aggressive-mode clien-endpoint       ipv4-address 2.2.2.1
Similarly on R2.
The below process is for the negotiation using RSA-SIG (PKI) as authentication type
Debug Process:
After we debug, we can see the negotiation between the two peers. The first packet of the interesting traffic triggers the ISAKMP (Phase1) negotiation. Important messages are marked in BOLD and explanation in RED
R2(config)#do ping 10.1.1.1 so lo0 // Interesting Traffic
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
Packet sent with a source address of 2.2.2.2
Mar 2 16:18:42.939: ISAKMP:(0): SA request profile is (NULL) // Router tried to find any IPSec SA matching the outgoing connection but no valid SA has been found in Security Association Database (SADB)
Mar 2 16:18:42.939: ISAKMP: Created a peer struct for 20.1.1.10, peer port 500
Mar 2 16:18:42.939: ISAKMP: New peer created peer = 0x46519678 peer_handle = 0x8000000D
Mar 2 16:18:42.939: ISAKMP: Locking peer struct 0x46519678, refcount 1 for isakmp_initiator
Mar 2 16:18:42.939: ISAKMP: local port 500, remote port 500
Mar 2 16:18:42.939: ISAKMP: set new node 0 to QM_IDLE
Mar 2 16:18:42.939: ISAKMP:(0):insert sa successfully sa = 4542B818
Mar 2 16:18:42.939: ISAKMP:(0):Can not start Aggressive mode, trying Main mode. // Not an error. By default it is configured for Main Mode
Mar 2 16:18:42.939: ISAKMP:(0):No pre-shared key with 20.1.1.10! // Since we are using RSA Signature, this message. If we use pre-share, this is where it would indicate so!
Mar 2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-rfc3947 ID
Mar 2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-07 ID
Mar 2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-03 ID
Mar 2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-02 ID
Mar 2 16:18:42.939: ISAKMP:(0):Input = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM
Mar 2 16:18:42.939: ISAKMP:(0):Old State = IKE_READY New State = IKE_I_MM1
Mar 2 16:18:42.943: ISAKMP:(0): beginning Main Mode exchange
Mar 2 16:18:42.943: ISAKMP:(0): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_NO_STATE // Sending ISAKMP Policy to peer
Mar 2 16:18:42.943: ISAKMP:(0):Sending an IKE IPv4 Packet.
Mar 2 16:18:42.943: ISAKMP (0): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_NO_STATE // Sending ISAKMP Policy to peer
Mar 2 16:18:42.947: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
Mar 2 16:18:42.947: ISAKMP:(0):Old State = IKE_I_MM1 New State = IKE_I_MM2
Mar 2 16:18:42.947: ISAKMP:(0): processing SA payload. message ID = 0
Mar 2 16:18:42.947: ISAKMP:(0): processing vendor id payload
Mar 2 16:18:42.947: ISAKMP:(0): vendor ID seems Unity/DPD but major 123 mismatch // Do not worry about this! Not an ERROR!
Mar 2 16:18:42.947: ISAKMP:(0): vendor ID is NAT-T v2
Mar 2 16:18:42.947:.!!!!
Success rate is 80 percent (4/5), round-trip min/avg/max = 1/2/4 ms
R2(config)# ISAKMP:(0): processing vendor id payload
Mar 2 16:18:42.947: ISAKMP:(0): processing IKE frag vendor id payload
Mar 2 16:18:42.947: ISAKMP:(0):Support for IKE Fragmentation not enabled
Mar 2 16:18:42.947: ISAKMP : Scanning profiles for xauth ...
Mar 2 16:18:42.947: ISAKMP:(0):Checking ISAKMP transform 1 against priority 10 policy
Mar 2 16:18:42.947: ISAKMP:      encryption 3DES-CBC
Mar 2 16:18:42.947: ISAKMP:      hash SHA
Mar 2 16:18:42.947: ISAKMP:      default group 2
Mar 2 16:18:42.947: ISAKMP:      auth RSA sig
Mar 2 16:18:42.947: ISAKMP:      life type in seconds
Mar 2 16:18:42.947: ISAKMP:      life duration (VPI) of 0x0 0x1 0x51 0x80
Mar 2 16:18:42.947: ISAKMP:(0):atts are acceptable. Next payload is 0
Mar 2 16:18:42.947: ISAKMP:(0):Acceptable atts:actual life: 0
Mar 2 16:18:42.947: ISAKMP:(0):Acceptable atts:life: 0
Mar 2 16:18:42.947: ISAKMP:(0):Fill atts in sa vpi_length:4
Mar 2 16:18:42.947: ISAKMP:(0):Fill atts in sa life_in_seconds:86400
Mar 2 16:18:42.947: ISAKMP:(0):Returning Actual lifetime: 86400
Mar 2 16:18:42.947: ISAKMP:(0)::Started lifetime timer: 86400.
Mar 2 16:18:42.947: ISAKMP:(0): processing vendor id payload
Mar 2 16:18:42.947: ISAKMP:(0): vendor ID seems Unity/DPD but major 123 mismatch
Mar 2 16:18:42.947: ISAKMP:(0): vendor ID is NAT-T v2
Mar 2 16:18:42.947: ISAKMP:(0): processing vendor id payload
Mar 2 16:18:42.951: ISAKMP:(0): processing IKE frag vendor id payload
Mar 2 16:18:42.951: ISAKMP:(0):Support for IKE Fragmentation not enabled
Mar 2 16:18:42.951: ISAKMP:(0):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
Mar 2 16:18:42.951: ISAKMP:(0):Old State = IKE_I_MM2 New State = IKE_I_MM2
Mar 2 16:18:42.951: ISAKMP (0): constructing CERT_REQ for issuer cn=ca_server OU=cisco C=India S=Karnataka L=Bangalore
Mar 2 16:18:42.951: ISAKMP:(0): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_SA_SETUP // Sending Key Exchange Information to peer
Mar 2 16:18:42.951: ISAKMP:(0):Sending an IKE IPv4 Packet.
Mar 2 16:18:42.951: ISAKMP:(0):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
Mar 2 16:18:42.951: ISAKMP:(0):Old State = IKE_I_MM2 New State = IKE_I_MM3
Mar 2 16:18:42.955: ISAKMP (0): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_SA_SETUP // Receive key exchange information from peer
Mar 2 16:18:42.955: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
Mar 2 16:18:42.955: ISAKMP:(0):Old State = IKE_I_MM3 New State = IKE_I_MM4
Mar 2 16:18:42.959: ISAKMP:(0): processing KE payload. message ID = 0
Mar 2 16:18:43.003: ISAKMP:(0): processing NONCE payload. message ID = 0
Mar 2 16:18:43.007: ISAKMP:(1008): processing CERT_REQ payload. message ID = 0
Mar 2 16:18:43.007: ISAKMP:(1008): peer wants a CT_X509_SIGNATURE cert
Mar 2 16:18:43.007: ISAKMP:(1008): peer wants cert issued by cn=ca_server OU=cisco C=India S=Karnataka L=Bangalore
Mar 2 16:18:43.007: Choosing trustpoint CA_Server as issuer
Mar 2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
Mar 2 16:18:43.007: ISAKMP:(1008): vendor ID is Unity
Mar 2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
Mar 2 16:18:43.007: ISAKMP:(1008): vendor ID seems Unity/DPD but major 180 mismatch
Mar 2 16:18:43.007: ISAKMP:(1008): vendor ID is XAUTH
Mar 2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
Mar 2 16:18:43.007: ISAKMP:(1008): speaking to another IOS box!
Mar 2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
Mar 2 16:18:43.007: ISAKMP:(1008):vendor ID seems Unity/DPD but hash mismatch
Mar 2 16:18:43.007: ISAKMP:received payload type 20
Mar 2 16:18:43.007: ISAKMP (1008): His hash no match - this node outside NAT
Mar 2 16:18:43.007: ISAKMP:received payload type 20
Mar 2 16:18:43.007: ISAKMP (1008): No NAT Found for self or peer
Mar 2 16:18:43.007: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
Mar 2 16:18:43.007: ISAKMP:(1008):Old State = IKE_I_MM4 New State = IKE_I_MM4
Mar 2 16:18:43.011: ISAKMP:(1008):Send initial contact
Mar 2 16:18:43.011: ISAKMP:(1008):My ID configured as IPv4 Addr, but Addr not in Cert!
Mar 2 16:18:43.011: ISAKMP:(1008):Using FQDN as My ID
Mar 2 16:18:43.011: ISAKMP:(1008):SA is doing RSA signature authentication using id type ID_FQDN
Mar 2 16:18:43.011: ISAKMP (1008): ID payload
          next-payload : 6
          type         : 2
          FQDN name    : R2
          protocol     : 17
          port         : 500
          length       : 10
Mar 2 16:18:43.011: ISAKMP:(1008):Total payload length: 10
Mar 2 16:18:43.019: ISAKMP (1008): constructing CERT payload for hostname=R2+serialNumber=FHK1502F2H8
Mar 2 16:18:43.019: ISAKMP:(1008): using the CA_Server trustpoint's keypair to sign
Mar 2 16:18:43.035: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_KEY_EXCH
Mar 2 16:18:43.035: ISAKMP:(1008):Sending an IKE IPv4 Packet.
Mar 2 16:18:43.035: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
Mar 2 16:18:43.035: ISAKMP:(1008):Old State = IKE_I_MM4 New State = IKE_I_MM5
Mar 2 16:18:43.047: ISAKMP (1008): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_KEY_EXCH
// "MM_KEY_EXCH" indicates that the peers have exchanged DH Public keys and generated a shared secret!
Mar 2 16:18:43.047: ISAKMP:(1008): processing ID payload. message ID = 0
Mar 2 16:18:43.047: ISAKMP (1008): ID payload
          next-payload : 6
          type         : 2
          FQDN name    : ASA1
          protocol     : 0
          port         : 0
          length       : 12
Mar 2 16:18:43.047: ISAKMP:(0):: peer matches *none* of the profiles // Normal Message! Not an error!
Mar 2 16:18:43.047: ISAKMP:(1008): processing CERT payload. message ID = 0
Mar 2 16:18:43.047: ISAKMP:(1008): processing a CT_X509_SIGNATURE cert
Mar 2 16:18:43.051: ISAKMP:(1008): peer's pubkey isn't cached
Mar 2 16:18:43.059: ISAKMP:(1008): Unable to get DN from certificate!
Mar 2 16:18:43.059: ISAKMP:(1008): Cert presented by peer contains no OU field.
Mar 2 16:18:43.059: ISAKMP:(0):: peer matches *none* of the profiles
Mar 2 16:18:43.063: ISAKMP:(1008): processing SIG payload. message ID = 0
Mar 2 16:18:43.067: ISAKMP:received payload type 17
Mar 2 16:18:43.067: ISAKMP:(1008): processing vendor id payload
Mar 2 16:18:43.067: ISAKMP:(1008): vendor ID is DPD
Mar 2 16:18:43.067: ISAKMP:(1008):SA authentication status:
          authenticated
Mar 2 16:18:43.067: ISAKMP:(1008):SA has been authenticated with 20.1.1.10
Mar 2 16:18:43.067: ISAKMP: Trying to insert a peer 40.1.1.1/20.1.1.10/500/, and inserted successfully 46519678. // SA inserted into SADB
Mar 2 16:18:43.067: ISAKMP:(1008):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
Mar 2 16:18:43.067: ISAKMP:(1008):Old State = IKE_I_MM5 New State = IKE_I_MM6
Mar 2 16:18:43.067: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
Mar 2 16:18:43.067: ISAKMP:(1008):Old State = IKE_I_MM6 New State = IKE_I_MM6
Mar 2 16:18:43.071: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
Mar 2 16:18:43.071: ISAKMP:(1008):Old State = IKE_I_MM6 New State = IKE_P1_COMPLETE
Mar 2 16:18:43.071: ISAKMP:(1008):beginning Quick Mode exchange, M-ID of -1523793378
Mar 2 16:18:43.071: ISAKMP:(1008):QM Initiator gets spi
Mar 2 16:18:43.075: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) QM_IDLE
Mar 2 16:18:43.075: ISAKMP:(1008):Sending an IKE IPv4 Packet.
Mar 2 16:18:43.075: ISAKMP:(1008):Node -1523793378, Input = IKE_MESG_INTERNAL, IKE_INIT_QM
Mar 2 16:18:43.075: ISAKMP:(1008):Old State = IKE_QM_READY New State = IKE_QM_I_QM1
Mar 2 16:18:43.075: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE
Mar 2 16:18:43.075: ISAKMP:(1008):Old State = IKE_P1_COMPLETE New State = IKE_P1_COMPLETE
Mar 2 16:18:43.079: ISAKMP (1008): received packet from 20.1.1.10 dport 500 sport 500 Global (I) QM_IDLE // IPSec Policies
Mar 2 16:18:43.079: ISAKMP:(1008): processing HASH payload. message ID = -1523793378
Mar 2 16:18:43.079: ISAKMP:(1008): processing SA payload. message ID = -1523793378
Mar 2 16:18:43.079: ISAKMP:(1008):Checking IPSec proposal 1
Mar 2 16:18:43.079: ISAKMP: transform 1, ESP_3DES
Mar 2 16:18:43.079: ISAKMP:   attributes in transform:
Mar 2 16:18:43.079: ISAKMP:      SA life type in seconds
Mar 2 16:18:43.079: ISAKMP:      SA life duration (basic) of 3600
Mar 2 16:18:43.079: ISAKMP:      SA life type in kilobytes
Mar 2 16:18:43.079: ISAKMP:      SA life duration (VPI) of 0x0 0x46 0x50 0x0
Mar 2 16:18:43.079: ISAKMP:      encaps is 1 (Tunnel)
Mar 2 16:18:43.079: ISAKMP:      authenticator is HMAC-SHA
Mar 2 16:18:43.079: ISAKMP:(1008):atts are acceptable. // IPSec attributes are acceptable!
Mar 2 16:18:43.079: ISAKMP:(1008): processing NONCE payload. message ID = -1523793378
Mar 2 16:18:43.079: ISAKMP:(1008): processing ID payload. message ID = -1523793378
Mar 2 16:18:43.079: ISAKMP:(1008): processing ID payload. message ID = -1523793378
Mar 2 16:18:43.083: ISAKMP:(1008): Creating IPSec SAs
Mar 2 16:18:43.083:         inbound SA from 20.1.1.10 to 40.1.1.1 (f/i) 0/ 0
          (proxy 1.1.1.1 to 2.2.2.2)
Mar 2 16:18:43.083:         has spi 0xA9A66D46 and conn_id 0
Mar 2 16:18:43.083:         lifetime of 3600 seconds
Mar 2 16:18:43.083:         lifetime of 4608000 kilobytes
Mar 2 16:18:43.083:         outbound SA from 40.1.1.1 to 20.1.1.10 (f/i) 0/0
        (proxy 2.2.2.2 to 1.1.1.1)
Mar 2 16:18:43.083:         has spi 0x2B367FB4 and conn_id 0
Mar 2 16:18:43.083:         lifetime of 3600 seconds
Mar 2 16:18:43.083:         lifetime of 4608000 kilobytes
Mar 2 16:18:43.083: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) QM_IDLE
Mar 2 16:18:43.083: ISAKMP:(1008):Sending an IKE IPv4 Packet.
Mar 2 16:18:43.083: ISAKMP:(1008):deleting node -1523793378 error FALSE reason "No Error"
Mar 2 16:18:43.083: ISAKMP:(1008):Node -1523793378, Input = IKE_MESG_FROM_PEER, IKE_QM_EXCH
Mar 2 16:18:43.083: ISAKMP:(1008):Old State = IKE_QM_I_QM1 New State = IKE_QM_PHASE2_COMPLETE // At this point tunnels are up and ready to pass traffic!
Verification Commands
#show crypto isakmp SA
#show crypto ipsec SA
Kindly rate if you find the explanation useful !!
Best Regards
Sachin Garg

Cisco asa 5505 with Router 881w Configuration Help

Hello all,
I'm having trouble setting up a second vlan to route to the internet. I have a Cisco ASA 5505 connected to my ISP(OUTSIDE) and a Cisco 881w (INSIDE) router in the back of my firewall. My vlan 10 with the network 192.168.5.1 255.255.255.0 works with pat, however vlan 15 that is on my 881w router does not route to the internet at all. I can only ping from 192.168.15.15 network to 192.168.5.1 I would like some advice on how can I make this set up work. Attached with this discussion is a picture of my topology.
Thanks in advance.
here are the show runs:
Cisco ASA 5505 show run:
ASA Version 8.3(1)
names
interface Vlan1
no nameif
no security-level
no ip address
interface Vlan5
mac-address xxxx.xxxx.xxxx
nameif OUTSIDE
security-level 0
ip address dhcp setroute
interface Vlan10
nameif INSIDE
security-level 100
ip address 192.168.5.1 255.255.255.0
interface Ethernet0/0
switchport access vlan 5
interface Ethernet0/1
switchport access vlan 10
interface Ethernet0/2
interface Ethernet0/3
shutdown
interface Ethernet0/4
shutdown
interface Ethernet0/5
shutdown
interface Ethernet0/6
shutdown
interface Ethernet0/7
shutdown
ftp mode passive
clock timezone CST -6
clock summer-time CDT recurring
object network INTERNAL_LAN
subnet 192.168.5.0 255.255.255.0
object network PRIVATE_LAN_192
subnet 192.168.15.0 255.255.255.224
description PRIVATE_LAN_192
access-list INSIDE_access_in extended permit ip any any
access-list INSIDE_access_in extended deny ip any any
access-list OUTSIDE_access_in extended permit ip any any
access-list OUTSIDE_access_in extended deny ip any any
pager lines 24
logging enable
mtu OUTSIDE 1500
mtu INSIDE 1500
ip verify reverse-path interface OUTSIDE
ip verify reverse-path interface INSIDE
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
object network INTERNAL_LAN
nat (INSIDE,OUTSIDE) dynamic interface
object network PRIVATE_LAN_192
nat (INSIDE,OUTSIDE) dynamic interface
access-group OUTSIDE_access_in in interface OUTSIDE
access-group INSIDE_access_in in interface INSIDE
route INSIDE 192.168.15.0 255.255.255.224 192.168.5.2 1
dynamic-access-policy-record DfltAccessPolicy
http server enable
dhcpd dns 8.8.8.8 75.75.76.76
dhcpd address 192.168.5.10-192.168.5.100 INSIDE
dhcpd enable INSIDE
Router 881w show run:
Current configuration : 4912 bytes
version 12.4
no ip source-route
ip dhcp excluded-address 192.168.15.1 192.168.15.10
ip dhcp pool PRIVATE_LAN
network 192.168.15.0 255.255.255.224
interface FastEthernet0
switchport trunk allowed vlan 1,15,1002-1005
switchport mode trunk
interface FastEthernet1
interface FastEthernet2
interface FastEthernet3
interface FastEthernet4
ip address 192.168.5.2 255.255.255.0
duplex auto
speed auto
interface wlan-ap0
description Service module interface to manage the embedded AP
no ip address
arp timeout 0
interface Wlan-GigabitEthernet0
description Internal switch interface connecting to the embedded AP
interface Vlan1
no ip address
interface Vlan15
ip address 192.168.15.1 255.255.255.224
no ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 FastEthernet4
no ip http server
ip http authentication local
ip http secure-server

The cable modem does not have any configuration. I cant add any to it. Its a cisco dpc3008. From vlan 10 i have no problem to get to the internet with the above configuration. My problem is just vlan 15.

VLAN problems with SG200-8P and Cisco ASA 5505 (Sec Plus license)

Hi, I've been pulling my hair out trying to get simple vlan trunking working between these devices.
Basically, no clients on VLAN 99 (guest) will receive DHCP ip addresses when plugged into the SG200. I have the SG200<>ASA VLAN trunk configured correctly, as I know it, and I've tried numerous variations (set trunk as general tag/untagged, etc., set the ap port to general tag/untag, etc). Both AP's work properly when connected to the ASA e0/3 port but either will only pull the "inside" VLAN dhcp address when connected to the SG200 switch
VLAN 1 - inside (has separate dhcp scope assigned by ASA)
VLAN 99 - guest (has separate dhcp scope assigned by ASA)
SG200
purpose
ASA 5505 (Sec Plus license)
purpose
g2
Trunk 1UP,99T
Ubiquiti AP (VLAN 1 works, VLAN 99 does not
g3
Access port 99T
vlan 99 does not work
g8
Trunk 1UP, 99T
< Trunk between switch and ASA >
Int e0/2
switchport trunk allowed vlan 1,99
switchport trunk native vlan 1
switchport mode trunk
Int e0/3
switchport trunk allowed vlan 1,99
switchport trunk native vlan 1
switchport mode trunk
Second ubiquiti AP
Both VLAN 1 and VLAN 99 clients work properly

Frustrated - yes. Confused - maybe not as much, but I could have put some more effort into the overall picture.
There are two VLANs (1 - native) and (99 - guest). There is a trunk port between the SG200 and the ASA configured as 1-untagged 99 - tagged.
No clients connected to the SG200 on VLAN 99 are able to access the ASA VLAN 99 using either a static VLAN IP address or DHCP. The problem occurs whether I configure the SG200 with an access port 99-tagged or Trunk port 1UP, 99T or general port 1U, 99UP or any combination thereof.
Anything connected to the SG200 on the native VLAN works properly.
Anything connected to the ASA VLANs (1 or 99) works properly
I have not yet tried to see what the switch is doing with the VLAN tags but I suspect I have some mismatch with the Linksys/Cisco SG200 way of setting up a VLAN and how traditional Cisco switches work.
I was hoping someone with a working SG200 - Cisco ASA setup could share their port/trunk/VLAN settings or perhaps point me in the right direction.
SG200 g2 - trunk port (1UP, 99T) -- Access Point
SG200 g2 - access port (99U)
SG200 g8 - trunk port (1UP, 99T) connected to ASA5505 e0/3
ASA5505 e0/3 (switchport trunk allowed vlan 1,99, switchport trunk native vlan 1, switchport mode trunk)
Thanks,

Azure multiple site-to-site VPNs (dynamic gateway) with Cisco ASA devices

Hello
I've been experimenting with moving certain on-premise servers to Azure however they would need a site-to-site VPN link to our many branch sites e.g. monitoring of nodes.
The documentation says I need to configure a dynamic gateway to have multiple site-to-site VPNs. This is not a problem for our typical Cisco ISR's. However three of our key sites use Cisco ASA devices which are listed as 'Not Compatible' with dynamic routing.
So I am stuck...
What options are available to me? Is there any sort of tweak-configuration to make a Cisco ASA work with Azure and dynamic routing?
I was hoping Azure's VPN solution would be very flexible.
Thanks

Hello RTF_Admin,
1. Which is the Series of CISCO ASA device you are using?
Thank you for your interest in Windows Azure. The Dynamic routing is not supported for the Cisco ASA family of devices.
Unfortunately, a dynamic routing VPN gateway is required for Multi-Site VPN, VNet to VNet, and Point-to-Site.
However, you should be able to setup a site-to-site VPN with Cisco ASA 5505 series security appliance as demonstrated in this blog:
Step-By-Step: Create a Site-to-Site VPN between your network and Azure
http://blogs.technet.com/b/canitpro/archive/2013/10/09/step-by-step-create-a-site-to-site-vpn-between-your-network-and-azure.aspx
You can refer to this article for Cisco ASA templates for Static routing:
http://msdn.microsoft.com/en-us/library/azure/dn133793.aspx
If your requirement is only for Multi-Site VPN then there is no option but to upgrade the device as Multisite VPN requires dyanmic routing and unfortunately there is no tweak or workaround due to hardware compatibility issue.
I hope that this information is helpful
Thanks,
Syed Irfan Hussain

Azure Site to Site VPN with Cisco ASA 5505

I have got Cisco ASA 5505 device (version 9.0(2)). And i cannot connect S2S with azure (azure network alway in "connecting" state). In my cisco log:
IP = 104.40.182.93, Keep-alives configured on but peer does not support keep-alives (type = None)
Group = 104.40.182.93, IP = 104.40.182.93, QM FSM error (P2 struct &0xcaaa2a38, mess id 0x1)!
Group = 104.40.182.93, IP = 104.40.182.93, Removing peer from correlator table failed, no match!
Group = 104.40.182.93, IP = 104.40.182.93,Overriding Initiator's IPSec rekeying duration from 102400000 to 4608000 Kbs
Group = 104.40.182.93, IP = 104.40.182.93, PHASE 1 COMPLETED
I have done all cisco s2s congiguration over standard wizard cos seems your script for 8.x version of asa only?
(Does azure support 9.x version of asa?)
How can i fix it?

Hi,
As of now, we do not have any scripts for Cisco ASA 9x series.
Thank you for your interest in Windows Azure. The Dynamic routing is not supported for the Cisco ASA family of devices.
Unfortunately, a dynamic routing VPN gateway is required for Multi-Site VPN, VNet to VNet, and Point-to-Site.
However, you should be able to setup a site-to-site VPN with Cisco ASA 5505 series security appliance as
demonstrated in this blog:
Step-By-Step: Create a Site-to-Site VPN between your network and Azure
http://blogs.technet.com/b/canitpro/archive/2013/10/09/step-by-step-create-a-site-to-site-vpn-between-your-network-and-azure.aspx
You can refer to this article for Cisco ASA templates for Static routing:
http://msdn.microsoft.com/en-us/library/azure/dn133793.aspx
Did you download the VPN configuration file from the dashboard and copy the content of the configuration
file to the Command Line Interface of the Cisco ASDM application? It seems that there is no specified IP address in the access list part and maybe that is why the states message appeared.
According to the
Cisco ASA template, it should be similar to this:
access-list <RP_AccessList>
extended permit ip object-group
<RP_OnPremiseNetwork> object-group <RP_AzureNetwork>
nat (inside,outside) source static <RP_OnPremiseNetwork>
<RP_OnPremiseNetwork> destination static <RP_AzureNetwork>
<RP_AzureNetwork>
Based on my experience, to establish
IPSEC tunnel, you need to allow the ESP protocol and UDP Port 500. Please make sure that the
VPN device cannot be located behind a NAT. Besides, since Cisco ASA templates are not
compatible for dynamic routing, please make sure that you chose the static routing.
Since you configure the VPN device yourself, it's important that you would be familiar with the device and its configuration settings.
Hope this helps you.
Girish Prajwal

Cisco ASA 5510 Site to Site VPN with Sonicwall

I am trying to setup a VPN tunnel between a Cisco ASA 5510 (Version 8.2(2)) and Sonicwall TZ200. I got tunnel up and going and I am able to ping the Cisco ASA internal IP from the Sonicwall LAN but nothing else works. When I try to ping a host behind the Cisco ASA from the Sonicwall LAN I get the following message "Asymmetric NAT rules matched for forward and reverse flows; Connection for tcp src outside:10.20.10.x/xxxx dst inside:10.20.2.x/xxxx denied due to NAT reverse path failures" on the ASA
Googling the above error shows issues with version 8.3 and later which looked like the nat commands were changed but the ASA I am working on is still on 8.2 and the other common issue is not adding a NAT exemption. I have double-triple checked that I did add a NAT exception rule from the hosts on the cisco network to the hosts on the Sonicwall network. Seems like I have hit a road block so any help would be appreciated. Thanks
Here are some excertps from the config file (10.20.2.0 behind the cisco and 10.20.10.0 behind the sonicwall)
nat (inside) 0 access-list nonat
access-list nonat extended permit ip 10.20.2.0 255.255.255.0 10.20.10.0 255.255.255.0
access-list outside_1_cryptomap extended permit ip 10.20.2.0 255.255.255.0 10.20.10.0 255.255.255.0
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set peer x.x.x.x
crypto map outside_map 1 set transform-set ESP-3DES-SHA
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 5
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 28800
group-policy SiteToSitePolicy internal
group-policy SiteToSitePolicy attributes
vpn-idle-timeout none
vpn-tunnel-protocol IPSec
split-tunnel-network-list none
tunnel-group x.x.x.x type ipsec-l2l
tunnel-group x.x.x.x general-attributes
default-group-policy SiteToSitePolicy
tunnel-group x.x.x.x ipsec-attributes
pre-shared-key *****
Added few excerpts from config file

Yes inspect icmp is enabled in global_policy
The ping requests time out (The only ping that works is when I ping from the remote side to the ASA internal IP address, no other pings from either side work)
#show crypto isakmp sa
1   IKE Peer: x.x.x.x
    Type    : L2L             Role    : responder
    Rekey   : no              State   : MM_ACTIVE
#show crypto ipsec sa
interface: outside
    Crypto map tag: outside_map, seq num: 1, local addr: x.x.x.x
      access-list outside_2_cryptomap extended permit ip 10.20.2.0 255.255.255.0 10.20.10.0 255.255.255.0
      local ident (addr/mask/prot/port): (10.20.2.0/255.255.255.0/0/0)
      remote ident (addr/mask/prot/port): (10.20.10.0/255.255.255.0/0/0)
      current_peer: y.y.y.y
      #pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
      #pkts decaps: 39543, #pkts decrypt: 39543, #pkts verify: 39543
      #pkts compressed: 0, #pkts decompressed: 0
      #pkts not compressed: 0, #pkts comp failed: 0, #pkts decomp failed: 0
      #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
      #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
      #send errors: 0, #recv errors: 0
      local crypto endpt.: x.x.x.x, remote crypto endpt.: y.y.y.y
      path mtu 1500, ipsec overhead 58, media mtu 1500
      current outbound spi: 0ED0F897
      current inbound spi : 596CCE6F
    inbound esp sas:
      spi: 0x596CCE6F (1500302959)
         transform: esp-3des esp-sha-hmac no compression
         in use settings ={L2L, Tunnel, PFS Group 2, }
         slot: 0, conn_id: 50327552, crypto-map: outside_map
         sa timing: remaining key lifetime (sec): 7440
         IV size: 8 bytes
         replay detection support: Y
         Anti replay bitmap:
          0xFFFFFFFF 0xFFFFFFFF
    outbound esp sas:
      spi: 0x0ED0F897 (248576151)
         transform: esp-3des esp-sha-hmac no compression
         in use settings ={L2L, Tunnel, PFS Group 2, }
         slot: 0, conn_id: 50327552, crypto-map: outside_map
         sa timing: remaining key lifetime (sec): 7440
         IV size: 8 bytes
         replay detection support: Y
         Anti replay bitmap:
          0x00000000 0x00000001

Cisco ASA 5505 Reset-I Problem with TCP State Bypass

Hello,
I have a Cisco ASA 5505 that functions as my primary firewall and a Mitel 5000 controller behind it. I have two external phone users that have been connecting through the firewall with no issues for six months until about two weeks ago. I am now seeing the following log entry on the phone trying to connect to the Mitel Controller.
6
May 16 2014
14:52:52
302014
72.135.115.37
6915
192.168.20.2
6801
Teardown TCP connection 1203584 for outside:72.135.115.37/6915 to inside:192.168.20.2/6801 duration 0:00:00 bytes 0 TCP Reset-I
My phones are designed to work with the Mitel 5000 and Mitel 3300 phone controllers. The 5000 will only use port 6800 for call control, while the 3300 will use 6801 (Secured Minet), 6802 (Minet SSH), and if those fail, port 6800 (Minet Unsecured). When the phones initiate a connection, they try 6801 first. If 6801 is unavailable, the phone controller adds the RST flag to the ACK packet. When the phone sees the RST flag, it is supposed to reset and use the next port (6802). The same process happens again for port 6802, then the phone knows to try 6800. The problem is that the ASA sees the RST flag now and terminates the connection at the firewall. Therefore, the phones never see the RST flag, and continue to try the connection with port 6801.
I have tried to use the TCP State Bypass feature to correct the situation, but the log shows that the connection is still being terminated immediately by the firewall. I am a novice when it comes to configuring the ASA. Any help would be greatly appreciated, as the company that I bought the phone system from is out of troubleshooting options. I do not think that I have made any changes to the firewall around this time. I have packet captures and logs from my ASA and I have wireshark data on the inside of my network. I need to figure out how to configure the ASA so that it ignores the RST flag and sends the packet back to the source.
Any help would be greatly appreciated!

Thanks Rizwan,
Still no luck. I can't even ping the otherside (office).. I am not sure if i'm running the debug rightway. Here are my results...
homeasa(config)# ping inside 10.10.5.254............. (Office CIsco ASA5505 IP on local side. I also tried pinging the server on other side (office) whic is @10.10.5.10 and got the same result)
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.10.5.254, timeout is 2 seconds:
Success rate is 0
homeasa(config)# debug crypto isakmp 7
homeasa(config)# debug crypto ipsec 7
homeasa(config)# sho crypto isakmp 7
^
ERROR: % Invalid input detected at '^' marker.
homeasa(config)# sho crypto isakmp
There are no isakmp sas
Global IKE Statistics
Active Tunnels: 0
Previous Tunnels: 0
In Octets: 0
In Packets: 0
In Drop Packets: 0
In Notifys: 0
In P2 Exchanges: 0
In P2 Exchange Invalids: 0
In P2 Exchange Rejects: 0
In P2 Sa Delete Requests: 0
Out Octets: 0
Out Packets: 0
Out Drop Packets: 0
Out Notifys: 0
Out P2 Exchanges: 0
Out P2 Exchange Invalids: 0
Out P2 Exchange Rejects: 0
Out P2 Sa Delete Requests: 0
Initiator Tunnels: 0
Initiator Fails: 0
Responder Fails: 0
System Capacity Fails: 0
Auth Fails: 0
Decrypt Fails: 0
Hash Valid Fails: 0
No Sa Fails: 0
Global IPSec over TCP Statistics
Embryonic connections: 0
Active connections: 0
Previous connections: 0
Inbound packets: 0
Inbound dropped packets: 0
Outbound packets: 0
Outbound dropped packets: 0
RST packets: 0
Recevied ACK heart-beat packets: 0
Bad headers: 0
Bad trailers: 0
Timer failures: 0
Checksum errors: 0
Internal errors: 0
hjnavasa(config)# sh crypto ipsec sa peer 96.xxx.xxx.118
There are no ipsec sas
homeasa(config)#

Configuring Cisco ASA for site to site VPN ( Issue with setting up local network)

OK, so our primary firewall is a checkpoint gateway. Behind that we have a cisco ASA for vpn users. I have a project at the moment where we need to connect to another company using site to site VPN through the cisco ASA, as the checkpoint gateway is unable to establish a permanent tunnel with the other companies Cisco ASA.
What would be the best practise for setting up the local network on my side? Create the network on the ASA and then use a L2 vlan to connect to the Core switch?
Setup a L3 interface on the core switch and point it towards the checkpoint gateway which would then point to the ASA?
When you have to select your local network through the site to site wizard do you have to put the inside network address of the ASA?
Our network is setup like this: Access layer switch > Core 6500 Switch > Checkpoint-Firewall > Internet
The ASA is connected to a checkpoint sub interface
Any help would be beneficial as im new to cisco ASAs
Thanks
Mark

Mark
If we understood more about your environment we might be able to give you better answers. My initial reaction was similar to the suggestion from Michael to use a L2 vlan. But as I think a bit more my attention is drawn to something that you mention in the original post. The ASA is there for VPN users. If the VPN users need to access your internal network then you probably already have something configured on the ASA that allows access to the internal network. Perhaps that same thing might provide access for your site to site VPN?
HTH
Rick

CISCO ASA WITH FORTIMAIL

Similar Messages

Maybe you are looking for