Cisco VPN client & Microsoft ISA firewall client.

Hi all,
could someone give me advice how to set
up Cisco VPN client to route traffic
to our proxy ISA 2004. We have installed
Microsoft firewall client on PCs but we dont know how to set up routing of IPSEC
to Proxy.
I know that this is maybe problem of Microsoft but maybe it is possible to do this directly in Cisco VPN client.
Any suggestions?
BR
jl

Be sure that the Department or organizational unit (OU) corresponds to the Cisco VPN Client group name, as configured in the PIX vpngroup name. Select the correct Certificate Service Provider (CSP) appropriate for your setup
http://cisco.com/en/US/tech/tk583/tk372/technologies_configuration_example09186a0080094e69.shtml

Similar Messages

Replacing MS ISA proxy with IronPort WSA proxy - ISA firewall client?

Replacing MS ISA proxy with IronPort WSA proxy - what about the ISA firewall client?
Does Cisco have an equivalent of the Microsoft ISA Firewall Client?
How does WSA handle complex protocols (such as ftp) through the proxy server?

We are replacing MS ISA proxy servers with IronPort WSA S370 proxy servers.
We have several apps that make use the MS firewall client.
The MS firewall client enables HTTP-tunneling of TCP & UDP through the ISA proxy servers instead of going through firewalls.
These apps use various ports - and there are rules setup on the ISAs specifially for these apps and their ports.
Also we have serveral uses of RPD, telnet, and SSH using the firewall client to HTTP-tunnel through the proxy servers -- and these have specific ISA rules setup for them too.
I can find HTTP-tunneling software - commercial and freeware - but can't find any that I think will work through the IronPort WSA S370 proxy servers.
Would like to find someone who has implemented HTTP-tunneling using IronPort WSA 370 proxy servers.
Thanks again for your input.

Windows 7 isa firewall client problem

Hi,
I have a problem with isa 2006 firewall client on windows 7 joined to domain , I can browse websites with webproxy but I cannot connect to any pop3 and smtp mailservers when using pop3 dns name on outlook, so if I add the full name of mail.something.com,
it does not work with (name cannot be resolved), it works when adding ip address, also if I try to access ftp servers on internet it does not work.
This only happens with windows 7 computers windows xp works correctly with firewall client.
If secure nat client is used on windows 7 they work (but I need to authenticate users by name).
I have searched many forums but cannot find a solution.
I have rule in isa server that allows http,https,ftp,ping,smtp,pop, even the rule that applies to me which have all outbound ports open had the same problem.
Thanks in advance.

Hello everyone,
I'm having the exact same issue at my workplace. i have a 2008R2 server running TMG 2010 and i have a pool of mixed client PCs (windows 7 and XP).
I use forefront firewall client for authentication and access.
I'm having the same trouble with name resolution in Outlook and another application but everything else works fine.
There is no issue when using SecureNat (setting up gateway) though, everything is resolved and works well ... it's so strange and it's driving me crazy.
It would be much appreciated to have a more reasonable solution other than shortcuts like setting a fake gateway.
Thank you in advance.
Best Regards,
N

Cisco VPN and Microsoft Virtual PC (xp mode under Windows 7)

I've installed XP under my users Windows 7 64 bit Enterprise. Unfortunately I set up networking for DHCP so that the host and guest (too much vmware :) ) get two different IP's.
So with Cisco anyconnect, I can't get the guest (i.e. the Win xp vm) to connect correctly. I want to change networking back to bridged and try that, but for the life of me I can't find where the settings are. I'm thinking that bridged (where
I don't have to try the Cisco client in the vm might work better)
But I"m in the US
My users in Australia
and right now I can't get remote tools to work on the host and talking this guy through it on the phone is not pleasant.
Are there instructions somewhere, and where is the full downloadable documentation for this product. I can find online, can't find a full downloadable copy

On Thu, 2 Sep 2010 14:34:57 +0000, Jim_St wrote:
I've installed XP under my users Windows 7 64 bit Enterprise.=A0=20
Unfortunately I set up networking for DHCP so that the host and guest=20
(too much vmware :) )=A0 get two different IP's.
So with Cisco anyconnect, I can't get the guest (i.e. the Win xp vm) to=20
connect correctly.=A0 I want to change networking back to bridged and =
try=20
that, but for the life of me I can't find where the settings are.=A0 I'm=
=20
thinking that bridged (where I don't have to try the Cisco client in=20
the vm might work better)
But I"m in the US
My users in Australia
and right now I can't get remote tools to work on the host and talking=20
this guy through it on the phone is not pleasant.
Are there instructions somewhere, and where is the full downloadable=20
documentation for this product. I can find online, can't find a full=20
downloadable copy
Bridged networking is what VMWare calls it and it works basically the
same as the way you don't like here. The guest will interact with the
NIC on the host and from the outsie it will present a second channel
with a different MAC address. This channel will acquire an IP address
of its own from the DHCP server.
But no matter what you do, the host and guest will NEVER EVER get the
same IP address!
Additionally, Cisco VPN by design will shut down ALL other network
interfaces when it connects the tunnel so the computer running Cisco
VPN will be effectively disconnected from the local network and
INSTEAD connected to the remote network. You cannot share this VPN
tunnel to another local computer and this includes the host.
Bo Berglund

OCS and Microsoft ISA Firewall

I am having problems accessing OCS externally through an MS ISA 2000 firewall. OCS is running on RH 2.1 AS.
Problems seem to occur around authentication. We are able to login as a user but can't access anything from there.
Would appreciate any assistance.

where able to get this resolved. I am having a similar issue with OCS 10G and ISA server 2004. I have configured the server rules but when I try to access the OCS page I get error 10051 ICMP network unreachable

Connecting through ISA firewall

I am tring to connect Contribute 3.11 through our company ISA
authentication (firewall). The network provider tells me that ports
20 and 21 are open for FTP but about halfway through the connection
process, I get prompted for authentication username and password. 3
tries and I'm out
. I have also tried full domainname\username with
password and that bombs too. Has anybody else seen this or know how
to get around it?
I can connect just fine on my home PC so I know my
destination settings and permissions are OK. Any help is greatly
appreciated.

1. You can specify proxy settings in Contribute by going to
Edit > Preferences > FTP Proxy.
2. try disabling any antivirus software or firewall running
on your system.
3. make sure you install the ISA Firewall Client in your
System:
http://www.isaserver.org/tutorials/Manually_installing_the_ISA_firewall_client.html
4. to verify if FTP is indeed enabled, try to type this in
IE: ftp://ftp.irs.gov
see if you can access the folders; if not, your system admin
is lying; ftp is not enabled
5. go to control panel > internet options > advanced;
make sure that user http 1.1 through proxy connections is checked

Cisco VPN Client and Quick VPN interaction?

I have both a Cisco VPN client for connecting to my company LAN and a QuickVPN client for connecting to my home LAN installed on my W2K laptop. Both start and run correctly, and both connect just as they should. My home LAN uses a WRV54G router to provide VPN connection. I can alternate back and forth between the two clients and connect to each LAN with no obvious issues, but not at the same time, of course.
Here's the question. When I connect to the home LAN, I can log on with no problem and I can remotely administer the WRV54G with no problem. I can ping all of the wired and wireless W2K computers on my home LAN with no problem. However, I cannot "see", browse or map any of the shared resources on my home LAN. I have created user accounts on the home LAN computers for my laptop and router logins and I have given these accounts permissions to my shared resources, but I still cannot get to them. Linksys tech support has been absolutely no help whatsoever, even after repeated attempts.
While trying to troubleshoot this myself, I've noticed that when the Cisco VPN client is running and I'm connected to my company LAN, the IP address and subnet of my computer is changed to ones assigned by the DHCP server at my company. This seems to happen because the Cisco client activates the "Local Area Connection Number 2" on my laptop and assigns IP addresses using it. However, when I'm using the QuickVPN client to connect to my home, the IP address and subnet of my laptop continues to be those assigned by whatever local network I'm connected to (e.g. hotel, etc).
I'm wondering if the QuickVPN is supposed to be assigning an IP address and subnet to my laptop from the WRV54G's DHCP server when I connect to my home LAN. If so, could the Cisco VPN client installed on my laptop be preventing that from happening?
Sorry for the long post, but I'm at my wit's end on this one and Linksys is just no help at all.

1. The Cisco VPN client creates a virtual interface on your computer. This allows you to route traffic to the tunnel. The QuickVPN client is simpler. It only encrypts the traffic to the other end. It does not use a virtual interface. That's why you don't have another IP address when connected with QuickVPN. QuickVPN only encrypts IP packets with IPSec from your computer to 192.168.1.* (or whatever you may use on your WRV LAN) and sends them to the WRV's public IP address.
2. Microsoft Windows file sharing and LAN network browsing depends on network broadcasts. Those only work inside a LAN. If you connect from the outside to a LAN, broadcasts won't go through the VPN tunnel. This means you cannot use standard name windows workgroup name resolution to access shares. Those are propagated with broadcasts which will never go through the VPN tunnel. This means you are not able to use workgroup browsing. All you can to do access your shares is to use the IP address of the other computer.
In short:
\\mycomputer\share won't work
\\192.168.1.50\share works
(assuming the general sharing setup is O.K., i.e. you can use sharing correctly inside your LAN).
Of course, firewalls on the server end may cause problems. Access comes in from a public IP address. This may be blocked. Check the firewall logs on the server to find out if this is the case or not.
Moreover, establishing the VPN connection from a private LAN to a private LAN may not work. This is due to the double network address translation which breaks IPSec and thus the connection. If the hotel uses private IP addresses, this may be the case. But in that case you won't get ping responses from your WRV LAN.
What definitively won't work is in case when the hotel uses the same IP address subnet as you. If the hotel uses 192.168.1.* addresses and your WRV uses 192.168.1.* addresses you cannot connect. QuickVPN does only IPSec tunneling. There is no address translation in QuickVPN. Therefore connecting the identical private IP address subnet through QuickVPN will never work because all addresses exists twice, once on either side.

Windows 8 Cisco VPN Client Issue

I connect to several of my customers with the Cisco VPN Client Version 5.0.07.0290 and all has been working fine. In the last week, virtually every Windows 8 machine has stopped working. The client connects fine, shows it's connected, but if I go to Status -> Statistics it just shows 0 in the Bytes Received and Sent. The Bypassed and Discarded increases, but I am unable to reach any system. Does anyone know what causes this or how to resolve it? This is a HUGE problem for me as all of the work we do for our customers is via their VPNs. Every non-Windows 8 PC still works fine. And these Windows 8 PCs have been working fine until just the last week. Browsing through, I've seen posts with this same issue, but none related to Windows 8 recently. They are all Windows 7, and my Windows 7 machines are working flawlessly.
Someone help!
Thanks,
Brian

Hi Brian,
IPSEC client on Windows 8 machine is not supported.
Cisco VPN Client 5.0.07 supports the following Microsoft OSs:
•Windows 7 on x64 (64-bit)
•Windows 7 on x86 (32-bit) only
•Windows Vista on both x86 (32-bit) and x64
•Windows XP on x86
VPN Client does not support the Tablet PC 2004/2005; and Windows 2000, NT, 98, and ME.
VPN Client supports smart card authentication on Windows 7, Vista, and XP. However, VPN Client does not support the ST Microelectronics smart card Model ST23YL80, and smart cards from the same family.
VPN Client supports up to one Ethernet adapter and one PPP adapter. It does not support the establishment of a VPN connection over a tethered link.
VPN Client 5.0.x is incompatible with the combination of Cisco Unified Video Advantage 2.1.2 and McAfee HIPS Patch 4 Build 688. To avoid system failures, uninstall either of these two applications, upgrade McAfee to the latest version, or use VPN Client 4.6.x.
To install the VPN Client, you need
•Pentium®-class processor or greater
•Microsoft TCP/IP installed. (Confirm via Start > Settings > Control Panel > Network > Protocols or Configuration.)
•50 MB hard disk space.
•128 MB RAM
(256 MB recommended)
•Administrator privileges
The VPN Client supports the following Cisco VPN devices:
•Cisco Series 5500 Adaptive Security Appliance, Version 7.0 or later.
•Cisco VPN 3000 Series Concentrator, Version 3.0 or later.
•Cisco PIX Firewall, Version 6.2.2(122) or Version 6.3(1).
•Cisco IOS Routers, Version 12.2(8)T or later.
you can get more information from following link:-
http://www.cisco.com/en/US/docs/security/vpn_client/cisco_vpn_client/vpn_client5007/release/notes/vpnclient5007.html#wp63537
Regards,
Naresh

Cisco VPN Client connects, but doesn't....

Have an issue where the workstation connects to the remote router using Cisco VPN Client successfully, but cannot receive traffic, but can...... I can see the connection with sh cry isa sa, and can see the packets encrypt/decrypt via sh cry ipse sa, as well as see the encrypt/decrypt in the VPN Client status, these numbers match up with the number of pings that are sent across the tunne. I can also see the ougoing and incoming packets with wireshark on the Cisco adapter on the workstation that is connected over the tunnel, icmp to:x.x.x.37 from:x.x.x.100, icmp from:x.x.x.100 to:x.x.x.37. Even with wireshark seeing the traffic, the requests time out. Any ideas?

Matthew,
If you are seeing packets encrypted/decrypted on both sites, but not getting an actual response, it sounds like tough one.
Have you tried disabling the client's firewall?
Also, you to discard a possible problem with the VPN virtual adapter have you tried to uninstall/reinstall the VPN Client?
Sorry, the suggetions I'm giving you are very basic but it definetely sounds kind of a weird problem...
Let me know how it goes.
Raga

Cisco VPN Client is not opening on windows 7 64bits

Hello,
My problem : i instaled Cisco VPN client 5.0.07.0440-k9 on Windows 7 64 bits, the installation ends successfully. But when i restard the computer, when i click it doesnt open.
Notice : when i restard the computer, it takes an infinite time the first rebooting , in the final stage of boot ( The black window with the Microsoft logo and message Windows Is Starting ...) '' it takes an infinite time so i force the reboot.
started the same thread here but no answer yet.
Thank you

check your event viewer/System log. You may see some entries stating that
"The Cisco Systems Inc. IPSec Driver failed to start due to the following error: Windows cannot verify the digital signature for this file."
disable digital signatures (NOT recommended) and cisco works fine
I guess Cisco has already killed this program if they aren't even getting it certified.

Strange issue with 3.6.3 VPN Client and IOS firewall

I'm able to establish a VPN connection from the VPN Client to the e0/0 interface of the IOS FW/VPN router and pass encrypted traffic.
Whenever I initiate a connection to something on the "Internet" from the LAN (e0/1) of the router, a temporary ACL entry is added to ACL 103 as it should be and I'm able to get out on the Internet from the internal LAN; however, I immediately lose my VPN connection from my PC Client when IOS FW adds those temporary "return entries".
Router is running 12.2(13)T.
Anyone else having issues like that? I've looked everywhere on cisco.com and elsewhere but I don't see anyone having a similar issue.
You Cisco gurus have any thoughts?
Thanks,
Jamey
Config below:
jamey#wr t
Building configuration...
Current configuration : 3947 bytes
! Last configuration change at 16:27:03 GMT Wed Jan 22 2003 by jdepp
! NVRAM config last updated at 00:14:38 GMT Wed Jan 22 2003 by jdepp
version 12.2
service timestamps debug datetime msec
service timestamps log datetime msec localtime show-timezone
service password-encryption
hostname "jamey"
no logging buffered
no logging console
username XXXX password 7 XXXXX
clock timezone GMT 0
aaa new-model
aaa authentication login tac local
aaa session-id common
ip subnet-zero
no ip domain lookup
ip inspect name myfw ftp
ip inspect name myfw realaudio
ip inspect name myfw smtp
ip inspect name myfw streamworks
ip inspect name myfw vdolive
ip inspect name myfw tftp
ip inspect name myfw rcmd
ip inspect name myfw tcp
ip inspect name myfw udp
ip inspect name firewall http java-list 3
ip audit notify log
ip audit po max-events 100
crypto isakmp policy 3
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp nat keepalive 20
crypto isakmp client configuration group XXXX
key XXXXXXX
dns x.x.x.x
domain xxx.com
pool ipsec-pool
acl 191
crypto ipsec security-association lifetime kilobytes 536870911
crypto ipsec security-association lifetime seconds 86400
crypto ipsec transform-set foxset esp-3des esp-md5-hmac
crypto dynamic-map dynmap 10
set transform-set foxset
crypto map clientmap client authentication list tac
crypto map clientmap isakmp authorization list XXXXX
crypto map clientmap client configuration address respond
crypto map clientmap 10 ipsec-isakmp dynamic dynmap
interface Loopback10
description just for test purposes
ip address 172.16.45.1 255.255.255.0
interface Ethernet0/0
description "Internet"
ip address x.x.x.x 255.255.255.224
ip access-group 103 in
ip inspect myfw out
no ip route-cache
no ip mroute-cache
half-duplex
crypto map clientmap
interface Ethernet0/1
description "LAN"
ip address 192.168.45.89 255.255.255.0
no ip route-cache
no ip mroute-cache
half-duplex
ip local pool ipsec-pool 192.168.100.1 192.168.100.254
ip classless
ip route 0.0.0.0 0.0.0.0 Ethernet0/0
no logging trap
access-list 3 permit any
access-list 103 permit ip 192.168.100.0 0.0.0.255 any log
access-list 103 permit icmp any any log
access-list 103 permit udp any eq isakmp any log
access-list 103 permit esp any any log
access-list 103 permit ahp any any log
access-list 103 permit udp any any eq non500-isakmp log
access-list 103 permit tcp any any eq 1723 log
access-list 103 permit udp any any eq 1723 log
access-list 103 deny tcp any any log
access-list 103 deny udp any any log
access-list 191 permit ip 192.168.45.0 0.0.0.255 192.168.100.0 0.0.0.255
access-list 191 permit ip 172.16.45.0 0.0.0.255 192.168.100.0 0.0.0.255
radius-server authorization permit missing Service-Type
call rsvp-sync
line con 0
line aux 0
line vty 0 4
exec-timeout 0 0
password XXXXXX
line vty 5 15
end
Some debugging info:
At this point, my VPN PC is successfully connected to the e0/0 VPN router and assigned IP of 192.168.100.2. It is running constant pings to 192.168.45.67 and 172.16.45.1 (172.16.45.1 is a loopback on the router for testing), 192.168.45.67 is a host on the internal network.
.Jan 22 01:27:38.284: ICMP type=8, code=0
.Jan 22 01:27:38.288: IP: s=192.168.45.67 (Ethernet0/1), d=192.168.100.2 (Ethern
et0/0), g=192.168.100.2, len 60, forward
.Jan 22 01:27:38.288: ICMP type=0, code=0
.Jan 22 01:27:38.637: IP: s=192.168.45.145 (Ethernet0/0), d=255.255.255.255, len
40, access denied
.Jan 22 01:27:38.637: UDP src=2301, dst=2301
.Jan 22 01:27:38.641: IP: s=192.168.45.145 (Ethernet0/1), d=255.255.255.255, len
40, rcvd 2
.Jan 22 01:27:38.641: UDP src=2301, dst=2301
.Jan 22 01:27:38.761: IP: s=<VPN PC CLIENT> (Ethernet0/0), d=<VPN ROUTER E0/0 INTERFACE> (Ethern
et0/0), len 112, rcvd 3, proto=50
.Jan 22 01:27:38.765: IP: s=192.168.100.2 (Ethernet0/0), d=172.16.45.1, len 60,
rcvd 4
.Jan 22 01:27:38.765: ICMP type=8, code=0
.Jan 22 01:27:38.765: IP: s=172.16.45.1 (local), d=192.168.100.2 (Ethernet0/0),
len 60, sending
.Jan 22 01:27:38.765: ICMP type=0, code=0
.Jan 22 01:27:39.282: IP: s=<VPN PC CLIENT> (Ethernet0/0), d=<VPN ROUTER E0/0 INTERFACE> (Ethern
et0/0), len 112, rcvd 3, proto=50
.Jan 22 01:27:39.286: IP: s=192.168.100.2 (Ethernet0/0), d=192.168.45.67 (Ethern
et0/1), g=192.168.45.67, len 60, forward
.Jan 22 01:27:39.286: ICMP type=8, code=0
.Jan 22 01:27:39.286: IP: s=192.168.45.67 (Ethernet0/1), d=192.168.100.2 (Ethern
et0/0), g=192.168.100.2, len 60, forward
.Jan 22 01:27:39.290: ICMP type=0, code=0
.Jan 22 01:27:39.763: IP: s=<VPN PC CLIENT> (Ethernet0/0), d=<VPN ROUTER E0/0 INTERFACE> (Ethern
et0/0), len 112, rcvd 3, proto=50
.Jan 22 01:27:39.767: IP: s=192.168.100.2 (Ethernet0/0), d=172.16.45.1, len 60,
rcvd 4
.Jan 22 01:27:39.767: ICMP type=8, code=0
.Jan 22 01:27:39.767: IP: s=172.16.45.1 (local), d=192.168.100.2 (Ethernet0/0),
len 60, sending
.Jan 22 01:27:39.767: ICMP type=0, code=0
.Jan 22 01:27:40.283: IP: s=<VPN PC CLIENT> (Ethernet0/0), d=<VPN ROUTER E0/0 INTERFACE> (Ethern
et0/0), len 112, rcvd 3, proto=50
.Jan 22 01:27:40.287: IP: s=192.168.100.2 (Ethernet0/0), d=192.168.45.67 (Ethern
et0/1), g=192.168.45.67, len 60, forward
.Jan 22 01:27:40.287: ICMP type=8, code=0
.Jan 22 01:27:40.287: IP: s=192.168.45.67 (Ethernet0/1), d=192.168.100.2 (Ethern
et0/0), g=192.168.100.2, len 60, forward
.Jan 22 01:27:40.291: ICMP type=0, code=0
.Jan 22 01:27:40.596 GMT: %SEC-6-IPACCESSLOGNP: list 103 permitted 50 216.16.193
.52 -> <VPN ROUTER E0/0 INTERFACE>, 222 packets
.Jan 22 01:27:40.596 GMT: %SEC-6-IPACCESSLOGP: list 103 permitted udp 216.16.193
.52(500) -> <VPN ROUTER E0/0 INTERFACE>(500), 16 packets
here is where I initiate a telnet connection to a host 2.2.2.2 (a dummy host on the "Internet")
from a host on the internal side (LAN) (192.168.45.1)
.Jan 22 01:27:40.600: IP: s=192.168.45.1 (Ethernet0/1), d=2.2.2.2 (Ethernet0/0),
g=2.2.2.2, len 44, forward
.Jan 22 01:27:40.600: TCP src=38471, dst=23, seq=953962328, ack=0, win=4128
SYN
.Jan 22 01:27:40.764: IP: s=<VPN PC CLIENT> (Ethernet0/0), d=<VPN ROUTER E0/0 INTERFACE> (Ethern
et0/0), len 112, rcvd 3, proto=50
here is where by VPN connection breaks
.Jan 22 01:27:40.768: IPSEC(epa_des_crypt): decrypted packet failed SA identity
check
.Jan 22 01:27:41.285: IP: s=<VPN PC CLIENT> (Ethernet0/0), d=<VPN ROUTER E0/0 INTERFACE> (Ethern
et0/0), len 112, rcvd 3, proto=50
.Jan 22 01:27:41.285: IPSEC(epa_des_crypt): decrypted packet failed SA identity
check
.Jan 22 01:27:45.773: IP: s=<VPN PC CLIENT> (Ethernet0/0), d=<VPN ROUTER E0/0 INTERFACE> (Ethern
et0/0), len 112, rcvd 3, proto=50
.Jan 22 01:27:45.777: IPSEC(epa_des_crypt): decrypted packet failed SA identity
check
.Jan 22 01:27:46.774: IP: s=<VPN PC CLIENT> (Ethernet0/0), d=<VPN ROUTER E0/0 INTERFACE> (Ethern
et0/0), len 112, rcvd 3, proto=50
.Jan 22 01:27:46.774: IPSEC(epa_des_crypt): decrypted packet failed SA identity
check

Ok..I found the bug ID for this:
CSCdz46552
the workaround says to configure an ACL on the dynamic ACL.
I don't understand what that means.
I found this link:
http://www.cisco.com/en/US/products/sw/secursw/ps2138/products_maintenance_guide_chapter09186a008007da4d.html#96393
and they talk about it, but I'm having a hard time decoding what this means:
"To specify an extended access list for a crypto map entry, enter the match address crypto map configuration command. This access list determines which traffic should be protected by IPSec and which traffic should not be protected by IPSec. If this is configured, the data flow identity proposed by the IPSec peer must fall within a permit statement for this crypto access list. If this is not configured, the router will accept any data flow identity proposed by the IPSec peer. However, if this is configured but the specified access list does not exist or is empty, the router will drop all packets."

Mac Lion and Cisco VPN client problems

I just installed Lion 10.7 on my iMac and can no longer use the downloaded Cisco VPN client to connect to Microsoft Remote Desktop and access the PC in my company's office. When I try to launch the VPN client I get Error 51. I used to be able to enter a command in the Terminal as a workaround to use the VPN client when that happened, but that no longer works. I have tried booting into 32-bit mode; doesn't work. I tried to use the Cisco client built into Lion using settings provided by my company. When I try to connect I get the following message: "The negotiation with the VPN server failed. Verify the server address and try reconnecting."
I have searched the web looking for a solution. My company's tech department is stumped; the Apple Geniuses haven't been able to help. Does anyone have any ideas how I can use either the downloaded Cisco VPN client or the client built into Lion?
Sent from Cisco Technical Support iPad App

Here is the link which you can use to configure the inbuilt VPN client in MAC Lion.
http://glazenbakje.wordpress.com/2011/07/28/how-to-create-a-cisco-vpn-connection-in-apple-mac-os-x-lion/
Make sure you configure the attributes correctly.
Secondly the inbuilt VPN client code of Lion is made in collaboration with Cisco so there will not be any issues of compatibility.
Cheers,
Rohan

IOS VPN will not respond to Cisco VPN Client connections.

Hi all,
I am about to set my routers on fire here.
I have two 2921 ISRs both with Security licenses on separate leased lines. I have configured one to accept VPN connections from our Cisco VPN Client remote workers.
I have followed the set up process I used on another site with an 1841/Sec router and the same clients and I have also checked against the config given in the latest IOS15 EasyVPN guide.
With all debugs active, all I see is
038062: Dec 8 14:03:04.519: ISAKMP (0): received packet from x.y.z.z dport 500 sport 60225 Global (N) NEW SA
038063: Dec 8 14:03:04.519: ISAKMP: Created a peer struct for x.y.z.z, peer port 60225
038064: Dec 8 14:03:04.519: ISAKMP: New peer created peer = 0x3972090C peer_handle = 0x8001D881
038065: Dec 8 14:03:04.523: ISAKMP: Locking peer struct 0x3972090C, refcount 1 for crypto_isakmp_process_block
038066: Dec 8 14:03:04.523: ISAKMP:(0):Setting client config settings 3E156D70
038067: Dec 8 14:03:10.027: ISAKMP (0): received packet from x.y.z.z dport 500 sport 60225 Global (R) MM_NO_STATE
Below is the abridged config.
System image file is "flash0:c2900-universalk9-mz.SPA.154-1.T1.bin"
aaa new-model
aaa authentication login default local
aaa authentication login VPNAUTH local
aaa authorization exec default local
aaa authorization network VPN local
aaa session-id common
crypto isakmp policy 10
encr aes
authentication pre-share
group 14
crypto isakmp client configuration group VPN
key ****-****-****-****
dns 192.168.177.207 192.168.177.3
domain xxx.local
pool VPNADDRESSES
acl REVERSEROUTE
crypto ipsec transform-set HASH esp-aes esp-sha-hmac
mode tunnel
crypto ipsec profile IPSECPROFILE
set transform-set HASH
crypto dynamic-map VPN 1
set transform-set HASH
reverse-route
crypto map VPN client authentication list VPNAUTH
crypto map VPN isakmp authorization list VPN
crypto map VPN client configuration address respond
crypto map VPN 65535 ipsec-isakmp dynamic VPN
ip local pool VPNADDRESSES 172.16.198.16 172.16.198.31
ip access-list extended REVERSEROUTE
permit ip 192.168.0.0 0.0.255.255 any
permit ip 10.0.0.0 0.0.0.255 any
ip access-list extended FIREWALL
2 permit udp any host a.b.c.d eq non500-isakmp
3 permit udp any host a.b.c.d eq isakmp
4 permit ahp any host a.b.c.d
5 permit esp any host a.b.c.d
If anyone can see anything wrong, I would be so pleased and it would save the destruction of an ostensibly innocent router.
Thanks,
Paul

> I actually love you. Thank you so much.
Sorry, I'm married ... ;-)
> Im not using a virtual template. Can I get away without the Crypto Map if I use one...? All my tunnels are VTIs
oh yes, I could have seen that ...
crypto isakmp profile VPN-RA
match identity group VPN
client authentication list VPNAUTH
isakmp authorization list VPN
client configuration address respond
virtual-template 1
interface Virtual-Template1 type tunnel
description Tunnel fuer Cisco VPN-Client
ip unnumbered GigabitEthernet0/0
ip virtual-reassembly in
tunnel mode ipsec ipv4
tunnel protection ipsec profile IPSECPROFILE
Your isakmp-config and ipsec profile stays the same.

I cannot install Cisco VPN Client 64-bit in windows 8

Hi
I bought new laptop which is preinstalled with widows 8 EM OS.. But for my usage i need to install cisco vpn client (64-bit version) software in my windows 8 EM OS.. which i cannot proceed actually because of the following error :
Error 28000 : Before installing the cisco systems vpn client 5.0.7.0290, you must uninstall the previous version of cisco systems vpn client 5.0.7.0290, using the Add/Remove program files option in the control panel, then restart your system
Following the above popup again a popup prompts displaying :
I have tried to uninstall the program from control panel but i could not find vpn client installed in my system at all... Please give me suggestion how to uninstall and install the new one..
Could you please advise how i can resolve the above issue and setup Cisco vpn client in my windows 8 OS? your reply is more worthy to carry on my work...

Hello,
The TechNet Wiki Forum is a place for the TechNet Wiki Community to engage, question, organize, debate, help, influence and foster the TechNet Wiki content, platform and Community.
Please note that this forum exists to discuss TechNet Wiki as a technology/application. If you have a question about another technology (such as Windows), you can ask in another forum. If you're unsure which forum, a Bing search often works the fastest or ask
here: http://social.microsoft.com/Forums/en-US/whatforum/threads
However, I'd ask in the
Windows 8 forum on Microsoft Community.
Karl
When you see answers and helpful posts, please click Vote As Helpful, Propose As Answer, and/or Mark As Answer.
My Blog: Unlock PowerShell
My Book: Windows PowerShell 2.0 Bible
My E-mail: -join ('6F6C646B61726C40686F746D61696C2E636F6D'-split'(?<=\G.{2})'|%{if($_){[char][int]"0x$_"}})

Unable to install Cisco VPN Client on Windows 7

Hello,
After a successfull uninstallation of Cisco VPN version 4. I try to install Cisco VPN Client version 5.0.07.0290.
But after launching vpnclient_setup.msi, the wizard is starting. When I click on Next button, I have the following message: "installation ended prematurely because of an error".
In attachment, I add the details of the error find in the windows logs (logError.txt) and the logs generated from MSI installer in verbose mode (log2.txt).
My computer is a lenovo W500 with Windows 7 64 bits and 4 GB of memory (compliant with the Cisco VPN Client requirements).
I have administrator privileges on this computer.
Please help me !
I need to use it to connect to my company network.
Thanks in advance.
BR
Jerome

You should be able to install the 64 bit version of the Cisco VPN software
Latest version is vpnclient-winx64-msi-5.0.07.0440-k9.exe
Using Shrew VPN is a workaround more than a solution / answer to this issue.
You should download and run MCPR.exe first, to clean out any traces of McAfee products that conflict with Cisco VPN.
http://download.mcafee.com/products/licensed/cust_support_patches/MCPR.exe
If there is a problem with vbscript registration on the system - there is a fixit tool from Microsoft for that:
MicrosoftFixit50842.msi

Cisco VPN client & Microsoft ISA firewall client.

Similar Messages

Maybe you are looking for