Client won't disconnect!

Hello all!
Platform: cisco 887 ios 15.0(1)M4
Client: iphone4s
Easy vpn server problem connection
When iphone goes standby disconnects from vpn server. When I try to reconnect, it disconnects immediately and won't reconnect . Here’s the debug output (debug crypto isakmp error):
000336: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access5, changed state to down
000337: At ISAKMP:(2056):Could not get address from pool!
000338: ISAKMP:(2056):deleting SA reason "Fail to allocate ip address" state (R) CONF_ADDR     (peer x.x.x.x)
000339: ISAKMP:FSM error - Message from AAA grp/user.
000340: ISAKMP:(0):Can't decrement IKE Call Admission Control stat incoming_active since it's already 0.
000341: ISAKMP:(2056):deleting SA reason "Fail to allocate ip address" state (R) MM_NO_STATE (peer x.x.x.x)
000342: ISAKMP:(0):Can't decrement IKE Call Admission Control stat incoming_negotiating since it's already 0.
With this configuration:
aaa new-model
aaa authentication login default local
aaa authentication login ATH local
aaa authorization exec default local
aaa authorization network GRP local
aaa session-id common
crypto isakmp policy 10
encr aes 256
authentication pre-share
group 2
crypto isakmp client configuration group VPN
key x
pool VCL
save-password
crypto isakmp profile IKE
   match identity group VPN
   client authentication list ATH
   isakmp authorization list GRP
   client configuration address respond
   keepalive 10 retry 3
   virtual-template 1
crypto ipsec transform-set TRS esp-aes 256 esp-sha-hmac
crypto ipsec profile SEC
set security-association idle-time 28800
set transform-set TRS
set isakmp-profile IKE
interface Virtual-Template1 type tunnel
ip unnumbered Dialer0
tunnel mode ipsec ipv4
tunnel protection ipsec profile SEC
ip local pool VCL 192.168.10.1
Which one should I smash? Iphone or cisco? This kept me busy now over 2 weeks. Clear commands won’t do anything. I have to reset dialer 0 interface to make work. Is there any command to clear interface as soon as client disconnects from vpn? Please help
Regards
Alex
edit:
client seems to stuck when it disconnects aggressively. When i remove local pool and apply it again with the same name the address is STILL in use!!!
The address is still in use even though client have disconnected hours ago:
#show ip local pool VCL
Pool                     Begin           End             Free In use   Blocked
VCL               192.168.10.1    192.168.10.1       0       1       0
Available addresses:
     None
Inuse addresses:
   192.168.10.1       IKE Addr IDB
Held addresses:    Time Remaining
     None
Pool                     Begin           End             Free In use   Blocked
VCL              192.168.10.1    192.168.10.1       0       1       0
Available addresses:
     None
Inuse addresses:
   192.168.10.1       IKE Addr IDB
Held addresses:    Time Remaining
     None
any help is much appreciated

Hello Herbert
Yes, i use only one client (iphone) for this profile to connect on my vpn. On a later post i wrote, i used this command "crypto ipsec security-association idle-time" and set it for 2 minutes. I thought that this solved the issue i had until yesterday! The same exact thing happend again!! This time i logged off from easy vpn server normaly and when i tried again i saw the same error message on the debug output!
I noticed from the command "show crypto eli" that my router allows 100 ipsec-sessions. So what i did was to log-in log off 100 times to see if that was the problem. Pathetic i know, took me over 10 mins but i wanted to see why? even though i logged off normaly why i couldn't access vpn server. Thankfully this was not the problem.
So far i don't have a clue! This is very frustrating thus i've spent many hours with no solution. Last night when this happend locked me out from my network over 10 hours until i got back home and reload the router (vpn led was off). There's no other way to get over it.
I have many issues with easy vpn client from iphone but this is the most critical for me so far. Now i've issued the command "crypto ipsec security-association idle-time 120 default" and hopefully it does something.
Finally i don't think giving more space would solve this. IPs get somehow stuck and never released no matter address space i give.
Thanx for your time

Similar Messages

IPod mini won't disconnect

After going through h--- with this ipod and getting it back up and running.....NOW it won't disconnect!! It did disconnect once, because I checked to make sure it was actually working. But, now it keeps saying that it cannot disconnect because some of it's files are being used by another application. I have no idea what this other application could be....any ideas or advice will be greatly (understatement!) appreciated! Thank you!

Easy way. Reset the iPod, then disconnect when you see the Apple logo.
Another way. Hold ctr-alt-del to bring up the Windows Task Manager. Go to the Processes tab and look for iTunesHelper.exe and iPodService.exe. Select them and hit the End Process button. Close the Windows Task Manager Window and try ejecting the iPod via the safely remove hardware method.
  If you are still having problems you can try one more thing. Right click on the My Computer icon and select Manage from the list of actions. Go to the Services and Applications item and from there the services item. Double click on the services item to bring up the list of services currently installed on your computer. Look for the iPod Service and double click on it. From the new window select Stop. Now try again to eject using the safely remove hardware option.
McAfee ActiveScan security software also can cause a problem, and if you have this you might want to try turning it off and see if the iPod then ejects correctly.
  If all else fails shut down the computer and disconnect the iPod.

What do I do with failed restore and an iPod that won't disconnect?

It's in disk mode and won't disconnect from the computer after a failure to restore...
help?

If you put your computer on standby, wait about 5 minutes and then start the computer back up - does that work?

Won't disconnect after syncing

iPod won't disconnect after sync. Says it's in use by another program. How do I find out what program is using it and why?

A background anti-virus scanner is one possible culprit as are other programs that might scan the drive when it connects such as Google/Windows desktop search tools. You should also make sure all Explorer windows/dialog boxes are closed, e.g a folder view of the iPod or a dialog saying something like. "This disk contains different types of items, what would you like Windows to do...?" Use ALT-Tab to cycle between windows as you may not even spot this one is there... it can open up behind iTunes without any other sign on screen, particularly in Vista. You may even need to quit iTunes before you can eject the disk if it has not closed files properly. Your milage may vary, but I often have to wait up to a minute after closing iTunes for it to announce that it is saving it's library and it may not be until this point that it properly closes all of it's open files.
tt2

Old clients won't switch from Self-Signed Certs to PKI.

Greetings.
I am wondering if anyone can give me advise on problem I am having with some of my sccm clients.
When I originally deployed SCCM i used self signed certs on clients.
We needed to add MAC and Linux support and MAC clients won't work without PKI, so I following this http://technet.microsoft.com/en-us/library/gg682023.aspx to configure Certificate Authority.
It all seemed work well, I can now join MAC client with auto-enroll and all machines are requesting client certificates and I had couple of machine with new push on windows site installed with PKI.
So right now I have about 250 windows clients, only 22 of them use PKI and the rest keeps using self-signed certs.
I foolishly switched main site settings, MP settings and DP point settings to use https only.
As a result I lost all self-signed clients and have full log for mpcontrol saying that it's rejecting clients cause they certificate cannot be validated.
I logged in to couple of those machines and MMC i can see that it did enroll machine with valid Client Cert but Configuration Manager client itself still saying that it's using self signed one.
Am I missing a step that I need to do to make sure that all those clients switch to PKI?

It is. but how can i redeploy them?
I was under impression auto push won't reinstall them. If i do deployment - that seem to reuse existing configuration and still use self signed on old machines.
How can i verify that it does push clients to machine that already have it correctly and start using new config and not reuse old one.
I even tried removing clients from couple of machines and see if it gets pushed again on them with proper config and those machines don't seem to get client but used to get it fine before. I keep getting new machines being added to domain and they get client
pushed to them, but anything that had client with self signed doesn't seem to be happy.

Intel wireless chipset clients random Citrix disconnects

Currently using intel 5100 & 6200 client cards on multiple driver versions. WiSM is 7.0.116. APs are 1250 and 1260 series. Citrix is setup to send server-side keepalives for session reliability. Randomly, several times a day the client will get disconnected from the Citrix application session but maintain connectivity to the AP and other applications continue to work. Traces show the server-side keepalive reach the controller but are delayed from controller to client by 5-6 seconds. Just enough time for the Citrix server to timeout and tear down to session. Additional testing shows the delay most likely occurs somewhere from controller to AP. It occurs on multiple controllers on multiple campuses.
We have Dell/Broadcom clients that don't experience the problem. The only commonality seems to be the Intel cards. Any ideas? CCX? I know Intel has a special relationship with Cisco regarding CCX and have developed features not available on other cards. Tried disabling power save and other CCX features but hasn't solved the issue. Any ideas are appreciated on this very strange problem.
Thanks!
Sent from Cisco Technical Support iPhone App

Update to this issue. I've found the 5 second delay actually is occurring on the AP. Packets traverse normally through the entire network but randomly delayed at the AP. TAC is looking at it but no cause found yet. Also verified this seems to occur only with Intel wireless chipsets. Others (Broadcom etc.) don't experience the problem.
Sent from Cisco Technical Support iPhone App

Fax modem won't disconnect

After sending faxes, the modem occassionally won't disconnect the phone line, keeping the line engaged until the computer is restarted. Even the "reset printing system" function doesn't correct this problem.
Has anyone else had this happen with the Mac mini and Panther, and how did you resolve it?
Thank you!

This is happening on my G4 Powerbook Aluminium) with Tiger. Extremely disappointing, seeing as the last time Apple had any decent faxing software was with ExpressFax that came with the PowerBook Duo Express Modem (circa 1994!!).
It would seem that whenever a fax is sent and the recipient doesn't answer, the modem doesn't hang up. When the modem is forced to hang up (ie by deleting the fax job or resetting the fax queue), it will not allow connections from either the fax queue or internet connect.
The only way I've been able to solve it is with a full, cold restart. Surely this is a bug - and surely it's high time Apple solved the whole faxing mess (cronically bad execution, bad ergonomics and low reliability) for good!

Lync 2010 Client won't start

The Lync 2010 client won't start.
Frequently the Lync 2010 client won't start. If you open up task manager you will see a back log of the Lync 2010 client, but the client won't open.

Agree with Georg.
I had the same problem.
End all Lync application tasks.
Then start Lync 2010 just for once.
Lisa Zheng
TechNet Community Support

DirectAccess Windows 8 Client Won't Connect - Last Error Code: 0x2af9

Hi All
Well I've had 2012 DirectAccess up and running now for about 2/3 weeks (using Win8 client only), it's been "ok" (most problems are client based - like Services not restarting upon resuming from sleep).
Yesterday I spent many hours connected to DirectAccess from my Windows 8 Laptop. When it's working, I love it.
Today, it's a completely different story.
Windows 8 won't damn well connect. At first I started getting prompted to enter proxy credentials (I have no idea why, have never been prompted for this before and the internal TMG proxy shouldn't even be in the loop, given my DA server has it's own
public IP address). The DA server has a completely separate public IP to the proxy's public IP address and the DA is setup with 2x NICs.
The error I'm getting is:
Interface IPHTTPSInterface (Group Policy) Parameters
Role                       : client
URL                        :
https://da.fqdn:443/IPHTTPS
Last Error Code            : 0x2af9
Interface Status           : failed to connect to the IPHTTPS server. Waiting to reconnect
Where do I find out what 0x2af9 error code means?

Hi,
The information for your errorcode seems to be related to not beeing able to lookup the host (the information from MSDN is pasted below.)
Can you verify that your client can resolve "da.fqdn" to the correct IPv4 address?
http://msdn.microsoft.com/en-us/library/windows/desktop/ms681391.aspx
WSAHOST_NOT_FOUND
11001 (0x2AF9)
No such host is known.
Jonas Blom | Relevo AB |
http://blog.nrpt.se
Hi Jonas
Thanks for your input. I think you might be right.
I suspected IE wasn't resetting my connection settings (even though I had un-ticked 'use a proxy server' - I don't think it had 'applied').
So, I did a reset of IE10, noticed all of the connection settings were gone and DA connected.
There definitely seems to be a gap in the DirectAccess solution in that it refers to the IE proxy/connection settings rather than just goes out to the Internet like Outlook does. When on the Domain, obviously you'll receive GPOs which in most organisations
that use things like Proxies (e.g. TMG) these GPOs will apply the proxy settings, but then when you disconnect from the Domain and you want to roam, those proxy settings need to be disabled - at least until DA has connected, then you're free to apply
the proxy as the gateway again.
It's a bit annoying.

Clients getting frequently disconnected - Interference issue !!!!!

Hi,
We have a 2504 WLC, recently past few weeks all the WiFi clients are facing frequent WiFi disconnectivity issue.
version: 7.6.130.14
Sample output of 1 AP out of total 5 (AIR-LAP1041N-E-K9).
>show ap auto-rf 802.11b APName
Interference Information
Interference Profile......................... FAILED
Channel 1.................................... -128 dBm @ 0 % busy
Channel 2.................................... -128 dBm @ 0 % busy
Channel 3.................................... -74 dBm @ 1 % busy
Channel 4.................................... -80 dBm @ 3 % busy
Channel 5.................................... -70 dBm @ 1 % busy
Channel 6.................................... -68 dBm @ 13 % busy
Channel 7.................................... -71 dBm @ 1 % busy
Channel 8.................................... -128 dBm @ 0 % busy
Channel 9.................................... -69 dBm @ 6 % busy
Channel 10................................... -65 dBm @ 4 % busy
Channel 11................................... -66 dBm @ 22 % busy
Channel 12................................... -72 dBm @ 8 % busy
Channel 13................................... -73 dBm @ 4 % busy
Can anybody recommend some workaround for this.
Will reducing the power level of AP help to resolve this issue.
>under TPC setting of 802.11b/g/n,
Maximum Power Level Assignment (-10 to 30 dBm) : its set to 30dbm
Power Level Assignment Method : Fixed : 3
DCA setting is Automatic and Channels are 1,6,11.
Regards

We have a 2504 WLC, recently past few weeks all the WiFi clients are facing frequent WiFi disconnectivity issue.
I think you're "barking at the wrong tree". Co-channel interference won't cause widespread clients disconnection issues.
What kind of clients are getting this issue? Computers? Smartphones? Tablets?
What's your encryption/authentication settings?
Have you tried running a debug on the clients during disconnection and reconnection?

Native VPN PPTP client won't stay connected

Folks,
I have setup my VPN using the Mac OSX native PPTP VPN client to connect to my client's work network. However, it appears that it won't stay connected. I have been searching the net for answers. I can't find a definitely one. Does anyone have the same issue where you can share your solution with me please?
To be more specific, I have a Windows XP laptop and a Mac. I connect to the same VPN on both machines. The Windows XP laptop will stay connected while the mac will drop the connection randomly. This is particularly true when my Mac went to sleep and then wake up.
In my PPTP VPN setup, I have already uncheck the option "Disconnect when user logs out" option in the Advance setting.
Also, this appears to be Mac OSX issue because I have another client where I can use the Cisco AnyWhere VPN client to connect and the connection stays connected all the time including the time when my Mac went into sleep mode.
My mac is the new MacBook Pro with Retina display running Mountain Lion (The original OS is Lion and then upgraded to Mountain Lion) and I am using the Thunderbolt to Ethernet adapter to connect to my wire network. It doesn't make much difference even if I switch over to a Wireless connection. In both cases, the VPN just won't stay connected.
Can someone point me to the right direction as to where I can trouble shoot this please? Thanks.

Thanks sberman. In the article, it mentions something about VPN on Demand, where in the setup do you see this setup? I am in the Network setup area and I am not finding this. Also, if I turn on the "Use verbose loggin", where is the log file? Is it still the /var/log/ppp.log file
Also, one more thing, my main ethernet connection setting does not include a proxy setting. But my VPN setup includes a proxy setting. Do you think that I may need to update the main ethernet setting to add the proxy setup to it as well? But I don't want to keep updating the main ethernet connection network setting to switch between proxy or not. Any suggestion will be welcome.
Thanks.

Switching WSUS server and Windows 8.1/Server2008/Server2012 clients won't connect, Windows 7/Server2003 is fine

I need to split the load of my WSUS on to another site because the amount of computers is straining the internet connection in the amount of uploads performed.
However I'm having an issue at the second WSUS where only Windows 7 and Server 2003 clients will update...
Windows 8.1 and Server 2008 and Server2012 won't update giving the following error codes: 8024400A and 80072EE2
The WSUS is a Server 2012 with Local Update Publisher 1.1 installed. It works fine locally at the site but not across our WAN.
The clients appear in the WSUS console but fail to check for updates.
I've tried it with the firewall turned off...
Both WSUS servers are using Microsoft SCEP 2012.
Has anyone out there experienced this? Or have any suggestions to fix?
Cheers.

Hi there,
I spoke too soon, I think I got one Windows 8 client to update yesterday by fluke. Now today it won't.
There's not much different between the W7 and W8 systems they both use the same antivirus. Same software but updated on W8.
Here is the windows update.log:
2014-06-05 10:44:14:561
976 954
Misc =========== Logging initialized (build: 7.9.9600.17093, tz: +1000) ===========
2014-06-05 10:44:14:639
976 954
Misc = Process: C:\Windows\system32\svchost.exe
2014-06-05 10:44:14:639
976 954
Misc = Module: c:\windows\system32\wuaueng.dll
2014-06-05 10:44:14:561
976 954
Service *************
2014-06-05 10:44:14:639
976 954
Service ** START ** Service: Service startup
2014-06-05 10:44:14:639
976 954
Service *********
2014-06-05 10:44:15:311
976 954
IdleTmr Non-AoAc machine. Aoac operations will be ignored.
2014-06-05 10:44:15:311
976 954
Agent * WU client version 7.9.9600.17093
2014-06-05 10:44:15:326
976 954
Agent WARNING: SleepStudyTracker: Machine is non-AOAC. Sleep study tracker disabled.
2014-06-05 10:44:15:326
976 954
Agent * Base directory: C:\Windows\SoftwareDistribution
2014-06-05 10:44:15:326
976 954
Agent * Access type: No proxy
2014-06-05 10:44:15:326
976 954
Service UpdateNetworkState Ipv6, cNetworkInterfaces = 1.
2014-06-05 10:44:15:326
976 954
Service UpdateNetworkState Ipv4, cNetworkInterfaces = 1.
2014-06-05 10:44:15:326
976 954
Agent * Network state: Connected
2014-06-05 10:44:15:326
976 954
Service UpdateNetworkState Ipv6, cNetworkInterfaces = 1.
2014-06-05 10:44:15:326
976 954
Service UpdateNetworkState Ipv4, cNetworkInterfaces = 1.
2014-06-05 10:44:16:123
976 954
Agent *********** Agent: Initializing global settings cache ***********
2014-06-05 10:44:16:123
976 954
Agent * Endpoint Provider: 00000000-0000-0000-0000-000000000000
2014-06-05 10:44:16:123
976 954
Agent * WSUS server: http://10.155.194.59:8530
2014-06-05 10:44:16:123
976 954
Agent * WSUS status server: http://10.155.194.59:8530
2014-06-05 10:44:16:123
976 954
Agent * Target group: Test Group
2014-06-05 10:44:16:123
976 954
Agent * Windows Update access disabled: No
2014-06-05 10:44:16:170
976 954
WuTask WuTaskManager delay initialize completed successfully..
2014-06-05 10:44:16:170
976 954
AU Timer: 31DA7559-FE27-4810-8FF6-987195B1FD98, Expires 2014-06-05 00:24:13, not idle-only, not network-only
2014-06-05 10:44:16:170
976 954
AU Timer: CF1ABEC6-7887-4964-BB93-B2E21B31CEC1, Expires 2014-06-05 05:36:25, not idle-only, not network-only
2014-06-05 10:44:16:170
976 954
AU Timer: 29A863E7-8609-4D1E-B7CD-5668F857F1DB, Expires 2014-06-05 05:36:25, not idle-only, not network-only
2014-06-05 10:44:16:170
976 954
Report CWERReporter::Init succeeded
2014-06-05 10:44:16:170
976 954
Agent *********** Agent: Initializing Windows Update Agent ***********
2014-06-05 10:44:16:170
976 954
DnldMgr Download manager restoring 0 downloads
2014-06-05 10:44:16:170
976 954
AU ########### AU: Initializing Automatic Updates ###########
2014-06-05 10:44:16:170
976 954
AU Additional Service {117CAB2D-82B1-4B5A-A08C-4D62DBEE7782} with Approval type {Scheduled} added to AU services list
2014-06-05 10:44:16:170
976 954
AU AIR Mode is disabled
2014-06-05 10:44:16:170
976 954
AU # Policy Driven Provider: http://10.155.194.59:8530
2014-06-05 10:44:16:170
976 954
AU # Detection frequency: 22
2014-06-05 10:44:16:170
976 954
AU # Target group: Test Group
2014-06-05 10:44:16:170
976 954
AU # Approval type: Scheduled (Policy)
2014-06-05 10:44:16:170
976 954
AU # Auto-install minor updates: Yes (Policy)
2014-06-05 10:44:16:170
976 954
AU # ServiceTypeDefault: Service 117CAB2D-82B1-4B5A-A08C-4D62DBEE7782 Approval type: (Scheduled)
2014-06-05 10:44:16:170
976 954
AU # Will interact with non-admins (Non-admins are elevated (Policy))
2014-06-05 10:44:16:186
976 954
AU WARNING: Failed to get Wu Exemption info from NLM, assuming not exempt, error = 0x80070032
2014-06-05 10:44:16:186
976 954
AU AU finished delayed initialization
2014-06-05 10:44:16:202
976 954
AU Adding timer:
2014-06-05 10:44:16:202
976 954
AU Timer: 31DA7559-FE27-4810-8FF6-987195B1FD98, Expires 2014-06-05 03:47:12, not idle-only, not network-only
2014-06-05 10:44:16:217
976 99c
DnldMgr Asking handlers to reconcile their sandboxes
2014-06-05 10:45:17:562
976 954
AU ReAttemptDownloadsAsUserIfNecessary, No calls in download progress.
2014-06-05 10:45:31:453
976 778
IdleTmr Incremented idle timer priority operation counter to 1
2014-06-05 10:45:34:562
976 778
AU Triggering AU detection through DetectNow API
2014-06-05 10:45:34:562
976 778
AU Additional Service {117CAB2D-82B1-4B5A-A08C-4D62DBEE7782} with Approval type {Scheduled} added to AU services list
2014-06-05 10:45:34:562
976 778
AU Triggering Online detection (interactive)
2014-06-05 10:45:34:562
976 778
AU Adding timer:
2014-06-05 10:45:34:562
976 778
AU Timer: 31DA7559-FE27-4810-8FF6-987195B1FD98, Expires 2014-06-05 00:45:34, not idle-only, not network-only
2014-06-05 10:45:34:609
976 954
AU #############
2014-06-05 10:45:34:609
976 954
AU ## START ## AU: Search for updates
2014-06-05 10:45:34:609
976 954
AU #########
2014-06-05 10:45:34:609
976 954
AU Additional Service {117CAB2D-82B1-4B5A-A08C-4D62DBEE7782} with Approval type {Scheduled} added to AU services list
2014-06-05 10:45:34:609
976 954
IdleTmr WU operation (CSearchCall::Init ID 1) started; operation # 15; does use network; is not at background priority
2014-06-05 10:45:34:609
976 954
IdleTmr Incremented idle timer priority operation counter to 2
2014-06-05 10:45:34:797
976 954
Report *********** Report: Initializing static reporting data ***********
2014-06-05 10:45:34:797
976 954
Report * OS Version = 6.3.9600.0.0.65792
2014-06-05 10:45:34:797
976 954
Report * OS Product Type = 0x00000004
2014-06-05 10:45:34:813
976 954
Report * Computer Brand = Microsoft Corporation
2014-06-05 10:45:34:813
976 954
Report * Computer Model = Virtual Machine
2014-06-05 10:45:34:813
976 954
Report * Platform Role = 1
2014-06-05 10:45:34:813
976 954
Report * AlwaysOn/AlwaysConnected (AOAC) = 0
2014-06-05 10:45:34:813
976 954
Report * Bios Revision = 090004
2014-06-05 10:45:34:813
976 954
Report * Bios Name = BIOS Date: 03/19/09 22:51:32 Ver: 09.00.04
2014-06-05 10:45:34:813
976 954
Report * Bios Release Date = 2009-03-19T00:00:00
2014-06-05 10:45:34:813
976 954
Report * Bios Sku Number unavailable.
2014-06-05 10:45:34:813
976 954
Report * Bios Vendor = American Megatrends Inc.
2014-06-05 10:45:34:813
976 954
Report * Bios Family unavailable.
2014-06-05 10:45:34:828
976 954
Report * Bios Major Release unavailable.
2014-06-05 10:45:34:828
976 954
Report * Bios Minor Release unavailable.
2014-06-05 10:45:34:828
976 954
Report * Locale ID = 3081
2014-06-05 10:45:35:578
976 954
Agent *** START *** Queueing Finding updates [CallerId = AutomaticUpdatesWuApp Id = 1]
2014-06-05 10:45:35:609
976 954
AU <<## SUBMITTED ## AU: Search for updates [CallId = {CDA6DEA2-9874-4DB5-AAA7-9A05D933C012} ServiceId = {3DA21691-E39D-4DA6-8A4B-B43877BCB1B7}]
2014-06-05 10:45:35:609
976 fc4
Agent *** END *** Queueing Finding updates [CallerId = AutomaticUpdatesWuApp Id = 1]
2014-06-05 10:45:35:609
976 fc4
Agent *************
2014-06-05 10:45:35:609
976 fc4
Agent ** START ** Agent: Finding updates [CallerId = AutomaticUpdatesWuApp Id = 1]
2014-06-05 10:45:35:609
976 fc4
Agent *********
2014-06-05 10:45:35:609
976 fc4
Agent * Online = Yes; Ignore download priority = No
2014-06-05 10:45:35:609
976 fc4
Agent * Criteria = "IsInstalled=0 and DeploymentAction='Installation' or IsPresent=1 and DeploymentAction='Uninstallation' or IsInstalled=1 and DeploymentAction='Installation' and RebootRequired=1 or IsInstalled=0
and DeploymentAction='Uninstallation' and RebootRequired=1"
2014-06-05 10:45:35:609
976 fc4
Agent * ServiceID = {3DA21691-E39D-4DA6-8A4B-B43877BCB1B7} Managed
2014-06-05 10:45:35:609
976 fc4
Agent * Search Scope = {Machine & All Users}
2014-06-05 10:45:35:609
976 fc4
Agent * Caller SID for Applicability: S-1-5-21-1323361640-3159480285-1943353560-1532
2014-06-05 10:45:35:609
976 fc4
Agent * RegisterService is set
2014-06-05 10:45:35:625
976 fc4
EP Got WSUS Client/Server URL: "http://10.155.194.59:8530/ClientWebService/client.asmx"
2014-06-05 10:45:35:641
976 fc4
Setup Checking for agent SelfUpdate
2014-06-05 10:45:35:641
976 fc4
Setup Client version: Core: 7.9.9600.17093 Aux: 7.9.9600.17093
2014-06-05 10:45:35:641
976 fc4
EP Got WSUS SelfUpdate URL: "http://10.155.194.59:8530/selfupdate"
2014-06-05 10:45:35:672
976 fc4
Misc Validating signature for C:\Windows\SoftwareDistribution\SelfUpdate\wuident.cab with dwProvFlags 0x00000080:
2014-06-05 10:45:35:734
976 fc4
Misc Microsoft signed: NA
2014-06-05 10:45:35:734
976 fc4
Misc Infrastructure signed: Yes
2014-06-05 10:45:35:734
976 fc4
Misc WARNING: Cab does not contain correct inner CAB file.
2014-06-05 10:45:35:734
976 fc4
Misc Validating signature for C:\Windows\SoftwareDistribution\SelfUpdate\wuident.cab with dwProvFlags 0x00000080:
2014-06-05 10:45:35:734
976 fc4
Misc Microsoft signed: NA
2014-06-05 10:45:35:750
976 fc4
Misc Infrastructure signed: Yes
2014-06-05 10:45:35:766
976 fc4
Setup Skipping SelfUpdate check based on the /SKIP directive in wuident
2014-06-05 10:45:35:766
976 fc4
Setup SelfUpdate check completed. SelfUpdate is NOT required.
2014-06-05 10:45:35:907
976 fc4
PT +++++++++++ PT: Synchronizing server updates +++++++++++
--continued--

Proxy client won't work in this case?

I have not made my client side work for a single device yet but I want to make sure I'm spending time on the right track:
My code will be running on the application server side, there will be hundreds of devices each has its own IP address, but runs exactly the same web services, and my code will need to talk to each of the selected ones using its IP address. I see that some generated proxy class contain the particular IP of the device where the web service is running on? If so, then it won't be possible for me to use a client proxy class to talk to all the devices.
I'm currently trying something like this:
URL url = new URL("http://172.21.159.52:80/cmi?wsdl");
QName serviceName = new QName("urn:Genus", "genusService");
Service service = Service.create(url, serviceName);
//These are for testing purpose
System.out.println ("List of QNames of service endpoints:");
Iterator it = service.getPorts();
*while (it.hasNext ()) {*
System.out.println (" " + it.next());
I can see the single service named 'genusPortType' in the output, however when the following code is reached:
QName portName = new QName("urn:Genus", "genusPortType");
Dispatch<SOAPMessage> dispatch = service.createDispatch(portName, SOAPMessage.class,Service.Mode.MESSAGE);
I got an error 'javax.xml.ws.WebServiceException: Illegal argument combination [type=javax.xml.soap.SOAPMessage,mode=MESSAGE]'. I'm confused because I see the same usage in lots of sample codes. Is it because the 'portName' part decides that these two parameters are not fit based upon the definition of 'genusPortType'? If the operation is defined like this in the wsdl file, wht values should I use?
*<wsdl:binding name="genusBinding" type="cmi:genusPortType">*
*     <wsdlsoap:binding style="rpc" transport="http://schemas.xmlsoap.org/soap/http" />*
*     *
*     <wsdl:operation name="login" >*
*          <wsdlsoap:operation soapAction="com.controlmod.terminal.services.web.services.Login#Login" />*
*          <wsdl:input name="loginRequest" >*
*          <wsdlsoap:body encodingStyle="http://schemas.xmlsoap.org/soap/encoding/" use="encoded" />*
*          </wsdl:input>*
*          <wsdl:output name="loginResponse" >*
*          <wsdlsoap:body encodingStyle="http://schemas.xmlsoap.org/soap/encoding/" use="encoded" />*
*          </wsdl:output>*
*     </wsdl:operation>*
*.............*

Sorry for really slow response on this - are you still here/still
having the issue?
Fillattr runs two migrations - one for access rules, and another for
proxy settings. I've seen cases where one works and the other fails.
But eventually you can get it going if you find the hangup.
Craig Johnson
Novell Knowledge Partner
*** For a current patch list, tips, handy files and books on
BorderManager, go to http://www.craigjconsulting.com ***

Email client won't working

Hi..
I have a problem till yesterday with iphone 4 email client..it won't show me my new emails..I just see 1 new message like notification and when I go to see inbox it is not there .
Pleas help me to fix this problem.
All the best
Dusica.

Well I know recently Google has started locking accounts (well where they can check from) when they are checked on too often or from too many different places.
My wife couldn't check her email anymore from new locations) until it got unlocked.
https://www.google.com/accounts/DisplayUnlockCaptcha to unlock an account.
For me I check from work computer, home computer, and my iPhone (thus AT&T ip assigned while in this home area). Never had an issue until I went on travel to another state and thus AT&T gave another IP and presto, kept getting bad user name or password messages when trying to check mail. Once doing the unlock I could check again.
Not sure if Yahoo is doing the same.

10.5 clients won't login/mount home directory

Hello all,
I am having some issues with 10.5.8 clients logging in network users. At our school, we have a "magic triangle" setup -- Mac and PC clients, an Active Directory for user authentication (a Win 2k3 server DC I believe), and an Open Directory server (running 10.7.5 OS X Server) for Workgroup Managment and software updates. Along with this, there is a Linux NAS box that acts as the file server hosting the user's home directories.
I have a few test student accounts that I have set up exactly the same way that normal student accounts are added to AD. Users have complained that these 10.5.8 clients will not let any students log on, as I have verified with my test student accounts. When logging in, an error comes up that says "Logging into the account failed because an error occurred". In secure.log I get a "smb_mount: syserror = Broken pipe" line along with
ERROR | -[HomeDirMounter mountNetworkHomeWithURL:attributes:dirPath:username:] | PremountHomeDirectoryWithAuthentication( url=smb://fileserver.domain.org/username, homedir=/Network/Servers/fileserver.domain.org/username, name=username ) returned 32
When I turn off "Create Mobile Account at Login", the user can log in just fine, which obviously leads me to believe that there is an issue with mounting the samba share for the user's home directory during the HomeSync.
I know the client can resolve the file server's hostname by nslookup, so I don't think DNS is the issue. But I'm all out of ideas after looking everywhere online, and am hoping someone can assist me with this. I'm just a computer technician and not a network sys admin by any means, but I know a good enough amount to try to troubleshoot this. Even my network manager is stumped, and his answer is to upgrade the client to 10.6, resolving that the issue is with 10.5. I want to try to solve this issue rather than having to re-image all the 10.5 machines.
Obviously school is out for the weekend, so I won't be back for a couple days to work on the issue if anyone does respond in the next couple days.
Thanks in advance!
-Brandon

Hi Brandon, certainly no expert at this, but let me trow this out at you...
Found a work-around. This command adds a delay, in this case 45 seconds, before displaying the Login Window.
defaults write /Library/Preferences/com.apple.loginwindow StartupDelay -int 45
If the Login Window UI detects that the network servers are available when it starts, it will skip the delay, also if network servers become available before the delay expires, the Login Window UI cancels the delay and displays.
Kent

Client won't disconnect!

Similar Messages

Maybe you are looking for