CME\7960 running SIP firmware - How do i setup incoming calls? - Can anyone help please?
Hi Guys,
I have a SIP trunk setup with a 2811 running CME version 7. I can make outbound calls ok but having issues getting the incoming calls working, i have 1 number on my SIP trunk and that is 01133501788 and i want that to ring my Cisco 7960 which is running SIP firmware not SCCP. I have included by config for anyone who can help me, i just want the incoming call to work.
Many Thanks.
Matthew.
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
logging message-counter syslog
no aaa new-model
clock timezone GMT 0
dot11 syslog
ip source-route
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.1.1
ip dhcp excluded-address 10.10.10.1
ip dhcp pool DATA_POOL
network 10.10.10.0 255.255.255.0
default-router 10.10.10.1
dns-server 188.92.232.50 188.92.232.100
ip dhcp pool VOICE_POOL
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server 188.92.232.50 188.92.232.100
option 150 ip 192.168.1.1
ip name-server 188.92.232.50
ip name-server 188.92.232.100
no ipv6 cef
multilink bundle-name authenticated
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
no supplementary-service sip moved-temporarily
no supplementary-service sip refer
sip
bind control source-interface FastEthernet0/1.20
bind media source-interface FastEthernet0/1.20
registrar server
voice class codec 1
codec preference 2 g711ulaw
codec preference 3 g711alaw
voice register global
mode cme
source-address 192.168.1.1 port 5060
max-dn 144
max-pool 42
load 7960-7940 P0S3-8-12-00
authenticate register
tftp-path flash:
create profile sync 0008072514198272
voice register dn 1
number 6999
allow watch
name SIP
label SIP
voice register pool 1
id mac 000F.902B.40E0
type 7960
number 1 dn 1
dtmf-relay sip-notify
username cisco password cisco
codec g711ulaw
voice translation-rule 1
rule 1 /^9\(.*\)/ /\1/
voice translation-rule 2
rule 1 /^6...$/ /4143*002/
voice translation-profile DiscardDigit9
translate calling 2
translate called 1
voice translation-profile IncomingSIP
translate calling 1133501788
voice-card 0
no dspfarm
username matt privilege 15 secret 5 $1$DCD0$SjWqnKgDSGVzzIKRerXh11
archive
log config
hidekeys
interface FastEthernet0/0
ip address 194.12.0.222 255.255.255.252
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
interface FastEthernet0/1
no ip address
ip nat inside
ip virtual-reassembly
duplex auto
speed auto
interface FastEthernet0/1.10
description DATA
encapsulation dot1Q 10
ip address 10.10.10.1 255.255.255.0
ip nat inside
ip virtual-reassembly
interface FastEthernet0/1.20
description VOICE
encapsulation dot1Q 20
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 194.12.0.221
ip http server
ip http authentication local
no ip http secure-server
ip nat inside source list 1 interface FastEthernet0/0 overload
access-list 1 permit 192.168.1.0 0.0.0.255
access-list 1 permit 10.10.10.0 0.0.0.255
tftp-server flash:P003-8-12-00.bin
tftp-server flash:P003-8-12-00.sbn
tftp-server flash:P0S3-8-12-00.loads
tftp-server flash:P0S3-8-12-00.sb2
tftp-server flash:P003-8-12-00
tftp-server flash:P003-8-12-00.loads
tftp-server flash:P003-8-12-00.sb2
tftp-server flash:SIP000F902B40E0.cnf.xml
control-plane
mgcp behavior g729-variants static-pt
dial-peer cor custom
dial-peer voice 2 voip
description Outgoing Geographic
translation-profile outgoing DiscardDigit9
destination-pattern 0[7]........
voice-class codec 1
session protocol sipv2
session target dns:sip.cloudcalling.co.uk
dtmf-relay rtp-nte
no vad
dial-peer voice 1 voip
description IncomingSIP
translation-profile incoming IncomingSIP
voice-class codec 1
session protocol sipv2
session target dns:sip.cloudcalling.co.uk
incoming called-number .T
dtmf-relay sip-notify rtp-nte
no vad
sip-ua
credentials username 4143*002 password 7 password realm sip.cloudcalling.co.uk
authentication username 4143*002 password 7 password
nat symmetric role passive
nat symmetric check-media-src
calling-info sip-to-pstn number set 4143*002
no remote-party-id
retry invite 3
retry register 3
timers connect 100
registrar dns:sip.cloudcalling.co.uk expires 60
sip-server dns:sip.cloudcalling.co.uk
host-registrar
gatekeeper
shutdown
telephony-service
load 7960-7940 P0S3-8-12-00
max-ephones 24
max-dn 30
ip source-address 192.168.1.1 port 2000
max-conferences 8 gain -6
web admin system name Admin secret 5 $1$Fktw$t9GQkdDdHmoYdwptO8.or.
transfer-system full-consult
create cnf-files version-stamp Jan 01 2002 00:00:00
line con 0
line aux 0
line vty 0 4
login
scheduler allocate 20000 1000
ntp server 85.119.80.232
end
Router#
You my friend are a star! worked straight away, many thanks. Just one more thing, when i make an outgoing call, it always appears as "blocked" on my phone, my sip trunk is set to allow CME to alter outgoing CLI's how would i program the outgoing CLI to 01133501788 also?
The new working config is below with your suggestion, which works!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
logging message-counter syslog
no aaa new-model
clock timezone GMT 0
dot11 syslog
ip source-route
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.1.1
ip dhcp excluded-address 10.10.10.1
ip dhcp pool DATA_POOL
network 10.10.10.0 255.255.255.0
default-router 10.10.10.1
dns-server 188.92.232.50 188.92.232.100
ip dhcp pool VOICE_POOL
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server 188.92.232.50 188.92.232.100
option 150 ip 192.168.1.1
ip name-server 188.92.232.50
ip name-server 188.92.232.100
no ipv6 cef
multilink bundle-name authenticated
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
no supplementary-service sip moved-temporarily
no supplementary-service sip refer
sip
registrar server
voice class codec 1
codec preference 2 g711ulaw
codec preference 3 g711alaw
voice register global
mode cme
source-address 192.168.1.1 port 5060
max-dn 144
max-pool 42
load 7960-7940 P0S3-8-12-00
authenticate register
tftp-path flash:
create profile sync 0015244443466064
voice register dn 1
number 6999
allow watch
name SIP
label SIP
voice register pool 1
id mac 000F.902B.40E0
type 7960
number 1 dn 1
dtmf-relay sip-notify
username cisco password cisco
codec g711ulaw
voice translation-rule 1
rule 1 /^6...$/ /4143*002/
voice translation-rule 3
rule 1 /^01133501788$/ /6999/
rule 2 /^1133501788$/ /6999/
voice translation-profile IncomingSIP
translate called 3
voice translation-profile Translatetrunk
translate calling 1
voice-card 0
no dspfarm
username matt privilege 15 secret 5 $1$DCD0$SjWqnKgDSGVzzIKRerXh11
archive
log config
hidekeys
interface FastEthernet0/0
ip address 194.12.0.222 255.255.255.252
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
interface FastEthernet0/1
no ip address
ip nat inside
ip virtual-reassembly
duplex auto
speed auto
interface FastEthernet0/1.10
description DATA
encapsulation dot1Q 10
ip address 10.10.10.1 255.255.255.0
ip nat inside
ip virtual-reassembly
interface FastEthernet0/1.20
description VOICE
encapsulation dot1Q 20
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 194.12.0.221
ip http server
ip http authentication local
no ip http secure-server
ip nat inside source list 1 interface FastEthernet0/0 overload
access-list 1 permit 192.168.1.0 0.0.0.255
access-list 1 permit 10.10.10.0 0.0.0.255
tftp-server flash:P003-8-12-00.bin
tftp-server flash:P003-8-12-00.sbn
tftp-server flash:P0S3-8-12-00.loads
tftp-server flash:P0S3-8-12-00.sb2
tftp-server flash:P003-8-12-00
tftp-server flash:P003-8-12-00.loads
tftp-server flash:P003-8-12-00.sb2
tftp-server flash:SIP000F902B40E0.cnf.xml
control-plane
mgcp behavior g729-variants static-pt
dial-peer cor custom
dial-peer voice 1 voip
description IncomingSIP
translation-profile incoming IncomingSIP
voice-class codec 1
session protocol sipv2
session target sip-server
incoming called-number .T
dtmf-relay sip-notify rtp-nte
no vad
dial-peer voice 2 voip
description Outgoing Geographic
translation-profile outgoing Translatetrunk
destination-pattern 0[7]........
voice-class codec 1
session protocol sipv2
session target dns:sip.cloudcalling.co.uk
dtmf-relay rtp-nte
no vad
sip-ua
credentials username 4143*002 password 7 password realm sip.cloudcalling.co.uk
authentication username 4143*002 password 7 password
nat symmetric role passive
nat symmetric check-media-src
calling-info sip-to-pstn number set 4143*002
no remote-party-id
retry invite 3
retry register 3
timers connect 100
registrar dns:sip.cloudcalling.co.uk expires 60
sip-server dns:sip.cloudcalling.co.uk
host-registrar
gatekeeper
shutdown
telephony-service
load 7960-7940 P0S3-8-12-00
max-ephones 24
max-dn 30
ip source-address 192.168.1.1 port 2000
max-conferences 8 gain -6
web admin system name Admin secret 5 $1$Fktw$t9GQkdDdHmoYdwptO8.or.
transfer-system full-consult
create cnf-files version-stamp 7960 Dec 17 2013 14:35:13
line con 0
line aux 0
line vty 0 4
login
scheduler allocate 20000 1000
ntp server 85.119.80.232
end
Router#
Similar Messages
-
my iphone 1st gen is stuck in recovery mode and every time i try to reinstall firmware i get an error code 1015 can anyone help please?
Make sure you are using current iTunes on your computer. Click the iTunes Tab at the top of this page. Or try to Restore your iPhone with a different computer.
-
My ipad 1 has never been updated and can't run many apps which makes it of not much use, how do I update it ? A simple step by step idiot proof guide would be best ! Can anyone help please ?
You can only update the iPad to iOS 5.1.1and you cannot go any higher. If you never updated that high, you can do so by using iTunes on your computer. You will have to connect the iPad to your computer with the cable and launch iTunes
You can read more here. Make sure that you read the section about using iTunes. The article starts off with using the Settings on the iPad for WiFi updates. That only works with the iPad 2 and higher that is already running iOS 5.
Update your iPhone, iPad, or iPod touch - Support - Apple -
I have a macbook pro and use BT homehub 3. can't work out how to connect my time capsule. can anyone help? thanks
Just need to plug the TC in to the hub in bridge mode.. do not try and bridge the homehub.. it is not possible with the setup BT uses.
To bridge the TC.. plug it directly into a computer by ethernet.. no other connection to the TC or the computer.
Press and hold in reset until the front LED flashes rapidly.. about 10sec.
Release the reset.
Open the airport utility and setup the TC to bridge mode.
The actual method depends on version of the OS and airport utility you use.
This is version 5.
Sorry I cannot post the v6 as I am on a snow leopard computer now. But you go to the network tab, and choose off bridge mode for method of connection. It will be NAT and dhcp by default.
Then setup wireless.. you have a number of choices here.
Either setup with the same SSID Security and password, as the homehub uses.. or a different name, and password..
Each method works fine.. but you sometimes have issues with wireless channels.. for now leave it on auto and see what happens.. if you have issues lock down the radio channels on both devices.. use one out of the following on each, 1, 6, 11 or 13 in UK.. so say 6 on the homehub then 13 onthe TC.
Update the TC.. unplug fromt the computer and plug it into the homehub.
If you have other issues with the setup tell us what OS you run so we can post suitable screenshots. -
How can I edit my website from another computer? and how can I create a new website next to the one, I already have? Can anyone help, please?
Move the domain.sites file from one computer to the other.
The file is located under User/Library/Application Support/iWeb/domain.sites. Move this file to the same location on the other computer and double click and iWeb will open it. Remember, it is your User Library that you want and not your System Library, as you will not find iWeb there.
Just create a new site on the same domain file and it will appear below the other site. If you want them side by side then duplicate your domain file and have one site per a domain file and they can then be side by side. -
Being new to iBook publishing I need to know if stats are available to determine how many times my iBook has been downloaded. Can anyone help please? I need to persuade someone that this really is worthwhile. Mr Ignorant.
The only people who can possibly assist you with this is Apple Customer Relations, call your local Apple contact number and ask for Customer Relations then explain your situation clearly and politely (be firm but don't rant).
You might want to investiage what the local laws are regarding defective goods and 'fit for use' definitions on warranties etc. Consumer Protection can be a useful tool to use or bargain with if needed ... -
I am trying to send an email to a group which I have created in my contacts. I would like to hide the list of email addresses but cannot see how to do this. Can anyone help please?
Thank you for your message.
I can see how you do that when using the 'normal' emailing system from my mailing box, but not when working from the contact application (the 'book' on the bottom icon bar with the @ on it).... -
can anyone help please. how do i get the home button to appear on the touch screen my home button has stopped working?
I have same problem.
However, I am unable to turn on Assistive Touch.
At one time I was able to activate it, but it went away and now I cant reactivate.
What is the solution? -
installed CS6 and all working except Photoshop. Says application will not run on this mac despite my having the necessary system requirement of OSX 10.6.8. Can anyone help please?
Hi - I have opened a second log with the same date and name and am now tracking down the problem.
This seems to be the problem for me: Error "Exit 6" or "Exit 7" | Install log | Read, write, system file errors | CS5, CS5.5 -
How do I change DNS to Business Catalyst servers. I am having problems can anyone help please?
How do I change DNS to Business Catalyst servers. I am having problems can anyone help please?
What problem are you having?
Have you read this KB? - Domain name and DNS: Quick reference -
When I try to update Adobe Flash Player I'm prompted to quit Safari and Dashboard Client. I quit Safari but I don' know how to quit Dashboard Client. Can anyone help with this challenge?
Carolyn,
Thank you. It worked
Angus. -
I have imported a Zip files, mp3 music to my Desktop. How do I move it into iTunes. I have tried d/drop and also Import to Library without success. Can anyone help, please?
Many thanks to Limnos and King Penguin.
I have discovered! I needed software to Unzip and was directed to Stuffit from the App Store. Suddenly it is simple.
Download Zip File to Desktop.
rt> Zip >Open with..... >Stuffit Progress Bar: 'Expanding' follows. Then a blue folder (manilla) returns to Desktop.
Open iTunes >File >Import to Library From drop down select the now expanded contents of Zip file, then >OPEN
iTunes takes over and imports - Job's Done!!
Thanks again -
I forgot my security questions and it says Forgot your answers? : Send reset security info email to n•••••@live.fr, but it is not one of my email adress and I don't know how to changes this, can anyone help please ?
I want to buy an app but I can't without these answersYou need to contact Apple. Click here, phone them, and ask for the Account Security team.
(87765) -
I cannot connect a Sony ILCE6000 camera for wireless downloading. Sony feels I need DLNE? They do not know how to make it work. Can anyone help OS10·9·5
I cannot use the software.. so you need to figure out where the problem is..
But let me suggest.. the Mac is not the issue and likely the info from Sony is also up the creek.. they make PC's after all.
It is far more likely the camera is having issues with the wireless network.
Do you know you have a connection to the home network on the camera.. ?? You have an IP address and some internet or local access at least?
How you will discover those things is by fiddling.. but if you can tell me what wireless AP you are using that will help. -
iMovie imports only about 75% of the lenght of clips from my camcorder, I can`t find out how to import entire clips. can anyone help please?
'''''"... I have about 20 bookmark folders and about 100 bookmarks altogether. " '''''
Firefox doesn't store bookmarks like that, sound like a Windows / IE favorites scheme used for '''''url''''' files and folders which isn't directly compatible with the way Firefox does things. Firefox uses a '''json''' file for bookmark backups, a '''bookmarks.html''' for import and export is bookmarks, and stores the users bookmarks in the '''places.sqlite''' file, along with browsing history.
Put those folders and bookmarks in the '''\user\Favorites\''' folder so they are in IE and export your IE Favorites in HTML format, so you can import them into Firefox.
In IE:
File > Import/Export - Export to HTML file
''then in Firefox:'' <br />
Bookmarks > Show All Bookmarks -> Import & Backup - Import HTML... = From HTML file
Maybe you are looking for
-
How to assign authorization objects to a cube
Hello, My cube includes 0profit_ctr which is marked as authorization relevant. Still in RSSM my cube is not included in the list of infocubes for an authorization object (zprofit) linked to 0profit_ctr. I'm therefore not able to enable that authoriza
-
Hello everyone, I am using the following MDX query on one of my SSRS report. SELECT NON EMPTY { [Measures].[Days Outstanding], [Measures].[Amt] } ON COLUMNS, NON EMPTY { ([Customer].[Customer].[Customer Key].ALLMEMBERS) } HAVING [Measures].[ Days Out
-
Access is denied error when launching HFM based Financial Reports
When attempting to run Financial Reports where the data source is an HFM application, users sometimes get the following error(s): Access is denied <BR>Access is denied Sometimes the error is more detailed: 1001:datasourcename=HOLX;errorMsg=Access is
-
Outbound IDOCs: queue in PI communication channel
Hi, i've got data delivered as IDOCs. I'd like to read the data at a specific moment in our scheduling process but we don't have any influence when they will be send, that means we need the data today exactly at 2:23 a.m. and tomorrow at 2:55 a.m. an
-
How to fix this QtyOnHand FMS query with SO and PO ShipDates.
Hi Forum, I have this query that returns available quantity that takes into account (from PO) on order and on commit (SO) based on dates of order and receive. declare @onhand as float, @openqty_s_order as float, @openqty_p_order as float set @onhand